Craftsman 486240383 User Manual 38 LAWN SWEEPER Manuals And Guides L0910181

CRAFTSMAN Lawn Sweeper Manual L0910181 CRAFTSMAN Lawn Sweeper Owner's Manual, CRAFTSMAN Lawn Sweeper installation guides

User Manual: Craftsman 486240383 486240383 CRAFTSMAN 38 LAWN SWEEPER - Manuals and Guides View the owners manual for your CRAFTSMAN 38 LAWN SWEEPER #486240383. Home:Lawn & Garden Parts:Craftsman Parts:Craftsman 38 LAWN SWEEPER Manual

Open the PDF directly: View PDF .
Page Count: 16

Download
Open PDF In Browser	View PDF

owners
monuol

Model No.
486.240383

38" HiGH PERFORMANCE
CRAFTSMAN LAWNSWEEPER
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully

• Assembly
= Operation
° Customer Responsibilities
• Repair Parts
Sears, Roebuck and Coo, Hoffman Estates,

IL. 60179 U.SA.
PRINTED

IN

U.S,A,

RULES FOR SAFE OPERATION
The following safety precautions are suggested. This
lawn sweeper' is designed, engineered and tested to
offer
reasonably
safe and effective
service,
provided it is operated in strict accordance with these
instructions_ Failure to do so may result in personal
injury. Always observe the rules for safe operation.
1,

Do not allow anyone to operate
without proper' instructions°

2.

Do not permit

3.

Do not push or tow sweeper too close to a fire,
because the hopper and brush wilt burn°

4,

Do not
wrapped

children

to operate

Operate sweeper at reduced speed on rough
terrain, in ditches, and on hillsides to prevent
tipping and loss of control. Stay alert for holes
or' other hidden hazards,

6_

This sweeper is not meant for street or highway
use. Watch for traffic
when sweeping
near
roadways,
Keep all nuts, bolts and screws tight to be sure
equipment
is in safe working condition.
Vehicle and attachments
should be stopped and
inspected for damage after striking a foreign
object and damage should be repaired before
restarting and operating the equipment.
Follow maintenance
instructions
as outlined in
this manual,

7.

the sweeper

8o

sweeper.

9.

attempt
to remove wire or string
around brush while brush is rotating.

Your lawnsweeper
carton and inner pack parts
carton contains parts as shown in the figure below.
The hardware
package contains two separate
packages, see figures 1 and 2 on page 3. Identify
all parts and layout as shown in the figure b'elow and
figures 1 and 2.

8,
9.
10,
11_
12,

Upper Hopper
Lower Hopper
Lower Hopper
Hopper Bag
Wind Screen

Tube, Left Hand
Tube, Right Hand
Tube, Left Hand

PARTS IN INNER PACK CARTON:

CARTON CONTENTS
Loose Parts in Carton
1.
Sweeper Housing Assembly
2.
Brace Rod
3.
Bag Retainer strap
4
Bag Frame Strap
5,
Bag Pivot Rod (1) 3/8" Dia
6
Bag Support Rods (2) 3/16" Dia
7
Upper Hopper Tube, Right Hand
CARTON

5,

13
14
t5
16
17
18
19

Rope
Height Adjustment
Strap
Hitch Bar
Hitch Bracket
Hitch Pin Bracket
Hopper Mount Arms (2)
Hardware Package (Not Shown)

CONTENTS
7

9

6

3

1t
18

15
17

NOTE
DO NOT mix contents

of hardware

packages.
CONTENTS OF HARDWARE PACK: (Figure 1).
Sweeper Housing Assembly
A
(1) Hitch Pin
B
(2) Spacers 1" Diao x 3/4" Long
C
(1) Cotter Pin t/8" x 3/4" Long
D
(1) Hex Bolt 3/8-16 x 1-1/2" Long
E
(1) Fiat Washer 17/32" x 1-1/2" x 1/8"
F
(9) Hex Lock Nuts 3/8-16 Thread
G
(3) Hex Bolts 3/8-16 x 1" Long
H
(2) Hex Bolts 3/8-16 x 3/4" Long
I
(2) Hex Bolts 3/8-16 x 1-I/4" Long
J
(4) Flat Washers 3/8" Std.
K
(1) Hitch Pin Spring
Hand Knob
L
(I)
M
(2) Carriage Bolt 5/t6-18 x 314" Long
N
(1) Spacer 13/32" I.Do x 5/8" OrD. X 3116"
O
(1) Hex Nut 5/16-18 Thread
P
(1) Grip
Q
(1) Lock Washer 5t16" ID
R
(1) Carriage Bolt 3/8"-16 x 1" Long
S
(2) Flat Washers 5/16" Std

L

CONTENTS OF HARDWARE PACK: (Figure 2)
Hopper Bag Assembly
AA (6) Truss Slotted Head Screws
#t0-32 x 5/8"
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
AM

FIGURE 2

(4)
(6)
(2)
(4)
(4)
(4)
(2)
(2)
(2)
(2)
(2)

114'" x t-1t4"

Hopper Mounting
Clamps
Hex Lock Nut #i0-32 Thread
Curved Head Bolts 1/4+20 x 1" Long
Hex Lock Nuts 1/4+20 Thread
Hex Bolts 5/16-t8 x 3/4" Long
Hex Lock Nuts 5/16-18 Thread
Hex Bolts 1/4-20 x lq/4"
Long
Bag Retainer Clevises
Cotter Pins 1/8 x 3/4" Long
Hex Bolts 3/8-16 x 3/4" Long
Hex Lock Nuts 3/8-16 Thread

#10 x 5f8

+--'G

CARRIAGE

318" x 314-

318"

1_

x t"

_
5116" x 3f4"'

c_(o

318- x 1318"' x 1-114"

_

x 314"

5/16"'
5f16"' STD,

HEX
LOCK
NUT

5/16"

P

5116"" LOCK
318'° STD,

FULL SIZE HARDWARE

17132"

x 1..1/2"

REFERENCE CHART

3

#10-32

114"' x 1"
CURVED

51t6" LOCK

ASSEMBLY INSTRUCTIONS
FOR SWEEPER HOUSING

TOP VIEW

TOOLS REQUIRED
(1) Adjustable Wrench
(1) 3/8" Open End or Box Wrench
(1) 7/16" Open End or Box Wrench
(1) 1/2" Open End or Box Wrench
(1) 9/16" Open End or Box Wrench
(1) Standard Screwdriver
(1) Pair of Pliers

3/8" x 1-1/2"
HEX BOLT
(BACK HOLE}
HITCH BRACKET
POSITION SEE
GROUP "B '°
PAGE 10

3/8" x 1"
HEX BOLT
FRONT HOLE)

NOTE
HITCH BRACKET
Right Hand (RHo) and left hand (L.H.)
are determined
from
operator's
position while seated on tractor.

;23._-----,/_
_

Refer to carton contents figure on page 2 and figure
1 on page 3 for parts and hardware needed to
assemble sweeper housing,
1o

2.

FIGURE 4
BOTTOM VIEW

Assemble
the hitch bar too the sweeper
housing;
place
hitch
bar under
sweeper
housing as shown in figure 3,
Secure hitch bar with two 3/8" x 1" hex bolts
and 3/8" lock nuts, See figure 3. Do not tighten
at this time.
3/8"

HEX LOCK NUT

\,

POSITION SEE
GROUPS "A"
PAGE 10

HITCH

HITCH
LARGE FLAT
WASHER

3/8"'
LOCK NUTS

\

BRACE ROD

\,

,

3/8"

\

x 1" HEX BOLTS
FIGURE 5

BAR

._

',
,\\

SWEEPER HOUSING
NOTE
Cut, the plastic tie down
height adjustment lever.

FIGURE 3
NOTE
Before assembling the hitch bracket
or hitch pin bracket to the hitch bar
refer to figures 4, 7 and page 10 to
determine which position is required
for your Sears riding mower or tractor.
3

Assemble the hitch bracket to hitch bar with one
3/8" x 1" hex bolt (in the front hole) and 3/8"
hex lock nut. Do not tighten at this time. See
figure 4,

4.

Assemble the hitch bracket with one 3/8" x
1-1/2" hex bolt (in the back hole), large ftat
washer and 3/8" hex lock nut. (Do not tighten
at this time). See figures 4 and 5.

5_,

4

holding

Assemble the two bag mount arms and top
ends of brace rod. See figure 6, Assemble the
top hole in arms to sweeper housing using two
3/8" x 3/4" hex bolts and 3/8" lock nut& The
notched side of mount arms face upward and
mount on the inside of housing. See figure 6,
Assemble the brace rod under hitch bar and
large washer in back hole of hitch bracket, then
assemble brace rod ends to bottom holes in
arms and sweeper housing, using two 3/8" x
1-1/4" bolts, 3/8" flat washers and 3/8" hex
lock nuts, See figures 5 and 6 Do not tighten
as this time.

Assemble the height adjustment strap (hole end)
to the sweeper housing. See figure 8. Place
5/16" x 3/4" carriage bolt through the square
hole in right hand side of sweeper housing, Next
place 3/8" flat washer next to housing, then
spacer into large hole on strap and over end of
carriage bolt. Secure with 5/16" flat washer,
5/16" lock washer and 5/16" hex nut. See figure
8.

9_

NOTCH
BAGMOUNT

3/8" x 3/4"
HEX BOLT

318" HEXLOCKNU1
3f8" FLAT
3/8" HEXLOCK

'3/8" x 1-1!4"
HEX BOI_T

5_16" x 314"
BOLT "

LARGE HOLE IN STRAP

111111
SWEEPER HOUSING

NLJT

5/16"

LOCK WASHER

BRACE
ROD END
5/t6"
FIGURE 6

_'_3!B"

6,

Pull brace rod up tight under large flat washer
and hold while tightening the two bottom bag
mount arm bolts assembled in step 5. NOW
TIGHTEN ALL BOLTS ASSEMBLED IN STEPS 2,
3, 4 and 5o

7.

Assemble
the hitch pin, spring and 3/8"
flatwasher
to the hitch pin bracket with one
1/8" x 3/4" cotter pin, See figure 7,

8,

FLAT WASHER

-\
5/16"' FLAT WASHER

FIGURE 8
10

Assemble other end of height adjustment
strap
to height adjustment handle., See figure 9_ Place
slot on strap in line with square hole in height
adjustment
handle,, Secure strap with 5/16" x
3/4" carriage bolt, 5/16" flat washer and hand
knob° See figure 9o NOTE: Lightly coat slot with
grease for ease of adjustment,

Assemble the hitch pin bracket and two 1" dia
x 3/4" long spacers to hitch bar with one 3/8"
x 1" carriage bolt and 3/8" hex lock nut,, See
figure 7, See page t0 for adjustment before connecting
lawnsweeper
to your Sears riding
mower or tractor_
I"'

HEX NUT.

(2) SPACER
DIA, x 3t4"

HEIGHT ADJUSTMENT

STRAP

1t8" x 3t4"
PIN

\

_RIP

HEIGHT
ADJUSTMENT
HANDLE

\

5/16" x 314"
CARRIAGE BOLT

5/16"

FLAT WASHER

HAND KNOB

FIGURE 9

11.
FIGURE 7

5

Assemble the grip, with finger knobs as shown,
to the height adjustment handle. See figure 9.

ASSEMBLY INSTRUCTIONS
FOR HOPPER BAG

Secure the. upper tubes
with
1/4"
x 1"
curved head bolt and hex lock nut. See figure
12,

3_

Refer to carton contents figure on page 2 and figure
2 on page 3 for hardware needed to assemble
hopper bag. See page 2 to identify both upper and
lower hopper tubes°
1.

Insert the left hand upper hopper tube through
the hopper bag stitched flaps, starting at the
center cut out in the top of the hopper bag, See
figures 10, 1t and 12. Repeat for the right hand
upper hopper tube.

114" x 1" CURVED HEAD BOLT
(OUTSIDE)

/
-,,,,o

114" HEX LOCK NUT
(INSIDE)

UPPER HOPPER TUBE
(LEFT HAND SHOWN)
BAG FLAP
CENTER CUT OUT
START

FIGURE 12

FIGURE 10

2_

Stide the two upper hopper tubes together, as
shown in figure 11, Line up the center holes.
.

Assemb)e
the two lower hopper tubes
as
shown in figure t3, Secure with 1/4" x 1"
curved head bolt and 1/4" hex lock nut, See
figure

13,

UPPER HOPPER TUBES
1/4" x 1"
CURVED HEAD BOLT

/
LowER
HOPPER
TUBES

1t4" HEX LOCK NUT

FIGURE 11

FIGURE 13

5_

Place assembled
bottom of hopper

lower hopper
tubes
into
bag as shown in figure 14.

8,

Assemble the upper and lower hopper tube
ends together with two 3/8" x 3/4" hex bolts,
(inside) and 3/8" hex lock nuts (outside). See
figure 14, Do not overtighten to allow for pivot.

8.

Assemble the frame strap to the lower hopper
frame° Secure with !/4" x 1-1/4" hex bolts and
1/4" lock nuts, See figure 16o

LOWER HOPPER TUBE

UPPER
=ER
TUBE
!8" HEX LOCK NUT
(OUTSIDE)
1f4"
FRAME

x 1-1/4" HEX BOLT
(OUTSIDE)

STRAP

FIGURE 16

t
- ---_
LOWER HOPPER TUBE

3f8" x 3/4" HEX BOLT
_J_
(INSIDE)

HOPPER BAG
BOTTOM

FIGURE 14

9,

7_

Secure the bag corners over lower hopper tube
by snapping the flap to bag bottom on both
sides, See figure 17,

Assemble the bag frame strap (bottom) and bag
retainer (top) to the front edge of bag bottom.
Place the bag retainer on top and frame strap
on bottom Secure with six #t0 x 5/8" slotted
screws, and #10-32 hex lock nuts. See figure t5.

FRONT EDGE OF BAG
,SNAP
FRAME_S]:RAP ./
#10 x 5/8"

SCREW

FIGURE 15

FIGURE 17
7

I2_ Slide pivot

_od through hole in side of upper
hopper tube that you just pierced in step 11_
Slide one mounting
clamp, two bag retainer
clevises, and one more mounting clamp onto rod
before rod is pushed into other hole on opposite
side of bag, See figure 20,

NOTE
RODS ARE SPRING STEEL AND
REQUIRE BENDING OR BOWING AS
SHOWN BELOW IN FIGURE 18. DO
NOT OVER BEND AND LOSE BAG
SUPPORT TENSION.

MOUNTING CLAMP

10. Assemble
the two hopper support
rods as
shown in figure 18. Place top end of rod into
hole in upper tube and bend rod outwards_and
snap bottom end of rod into hole in bottom tube

PIVOT ROD

MOUNTING

CLAMP

FIGURE 20

13

Secure the bag retainer clevis on each side of
bag with 1/8" x ,3/4" cotter pins, See figure 21.
Wrap cotter pin around pivot rod as shown in
figure 21

FIGURE 18
11, Locate hole along side of upper hopper tubes
and pierce a hole through the bag aligned with
the hole in the tube, See figure 19.

I

_NOTE
Bag retainers must

pivot freely

UPPER HOPPER TUBE

/
I

BAG RETAINER C

ROD
'_"= _.__..=

FIGURE

FIGURE 21

19
R

CROSS-SECTION
_'OF
PIVOT ROD

16. Assemble

14, Assemble the two remaining hopper mounting
clamps to the outside of bag frame ,with 5/16"
x 3/4" hex bolts and 5/16" hex lock nuts. See
figure 22_ Tighten securely.

the wind screen over the top of
hopper bag frame by simply hooking the top
corner loops and pull the bottom loops down
over the ends of the pivot rod, See figure 24°

WIND SCREEN
MOUNTING

TOP CORNER LOOP

CLAMP

5/16" x 3/4"
HEX BOLTS

51t6"

HEX LOCK NuTs
OF PIVOT
ROD

FIGURE 22
FIGURE 24

17, To assemble the hopper bag frame to the
sweeper, simply hook the pivot rod into the
notches in mounting arms. Bag retainers must
pivot freely to lock in position,. See figure 25,.
18.

15.

Secure the rope to the top center of hopper
bag frame as shown in figure 23_

To remove the hopper bag frame from
sweeper, simply lift up on the bag retainers
lift off hopper bag. See figure 25

the
and

BAG RETAINER
HOPPER BAG FRAME

-"

PIVOT ROD

I

HOPPER MOUNT ARM

FIGURE 23

FIGURE 25
9

BRUSH HEIGHT ADJUSTMENT
APPROXIMATELY CENTERED

IMPORTANT
TO AssURE

BEST PERFORMANCE

oF

YOUR

NEW SWEEPER, THE FOLLOWING
INSTRUCTIONS MUST BE READ CAREFULLY. SEE FIGURE
26. YOU MUST
SET UP SWEEPER TO THE
TOWING VEHICLE, SO BOTTOM OF BAG FRAME
IS APPROXIMATELY
LEVEL ON FLAT SURFACE,
SUCH AS DRIVE OR WALK. THIS SHOULD KEEP
BAG OFF THE GROUND APPROXIMATELY 5" TO
LEVEL
SURFACE

LAWN TRACTORS IN TODAYS MARKET VARY IN
HEIGHT FROM GROUND TO HITCH APPROX_
IMATELY 8" TO 13" TO OBTAIN THE CORRECT
SWEEPER BAG LEVEL, SEE FIGURE 26. THERE
ARE EIGHT DIFFERENT
SPACER POSITIONS
AVAILABLE. SEE GROUPS A AND B.

APPROXIMATELY LEVEL
(5" to 7" FROM SURFACE)

FIGURE 26

GROUP "A'" - For vehicles with
8" to 10" ground clearance to
hitch.
HITCH

GROUP "B"
- For vehicles
with
10" to 13" ground
clearance to hitch.

BAR

WITH HITCH BRACKET MOUNTED
BELOW HITCH BAR

\

WITH HITCH BRACKET MOUNTED
BELOW HITCH BAR

HITCH BAR

BLACK LINE IS TRACTOR HITCH

TWO

_

SPACERS

ABOVE

BLACK LINE IS TRACTOR HITCH

TRACTOR

ONE SPACER ABOVE
AND BELOW TRACTOR

PA;% ER ABOVE AND BELOW

_, HITCH
, o

R HITCH

TWO SPACERS BELOW TRACTOR
HITCH

TWO SPACERS BELOW TRACTOR
HITCH

10

OPERATION

g_

Your sweeper is a precision piece of equipment.
Engineering
skill
and experience
have
been
) combined
to provide
reasonable
safety
and
efficiency. However, as with any type of mechanical
equipment,
carelessness or error on the part of the
operator can result in damage to your equipment,
Therefore,
exercise care at all times and do not
subject your lawnsweeper
to misuse.
SWEEPING SPEED
Try sweeping at different speeds to find the one most
suited to your conditions for maximum hopper bag
fill

Do Not drive or dump
the
sweeper too close to a fire as the
brushes
and
bag
can
be
destroyed
by excessive heat or
flame,

BRUSH HEIGHT ADJUSTMENT
To adjust your sweeper brushes to the best operating
height, loosen the adjustment knob and push down
on height adjustment
lever to raise the brush, See
figure 27, Best adjustment
is when brush setting is
1/2" down into grass. Always mow the grass to an
even height before sweeping,
FIGURE 28
TO LOWER BRUSH
(Pull Back)

STORAGE
HEIGHT
]STMENT
LEVER

The bag may be collapsed for storage,
two support rods and fold bag down

Remove

CUSTOMER ' RESPONS0BIMTIES
The bearings in the sweeper have been prelubricated
at the factory; however, it is recommended
that a
few drops of light oil should be added to the brush
shaft bearings twice a year Also. the wheels should
be removed every two years to clean sprockets, chain
and gears After cleaning apply an even coat of light
grease, See figures 29 through 31. NOTE: Do not
overtighten wheel bolt and nut upon reassembly to
sweeper housing Wheel must be free to move in slot
with height adjustment°
See figure 29 and 30,

TO RAISE BRUSH
(Push Down)

FIGURE 27
DUMPING OF SWEEPER
"Your sweeper can be dumped easily without getting
off of the rider or tractor_ Simply pull rope forward
to dump, See figure 28, SEE CAUTION NOTE A AND
Bo
Always dump hopper after each use, Damp or wet
grass and leaves will cause damage to hopper if
stored for along period of time..
HUB

FIGURE 29
_CAUTION
A,

the

-NOTE

Do Not fasten rope to pulling
vehicle where it might become
entangled with driving wheels or
rotating parts.

To remove wheel just pop off hub cap
with a screw driver and remove hex
bolt, nut and two flatwasherso See
figures 29 and 30.
1t

HEIGHT
ADJUSTMENT
•
COVER
OIL BEARINGS

AND
GREASE

HEX BOLT
FIGURE 30

FIGURE 32

WHEEL GEARS/PAWL SERVICE
1.

2,

3.

4.

BRUSH REPLACEMENT

To service wheel gears, Do Not Remove both
wheels at the same time. Remove one wheel
at a time to prevent use of left hand parts on
right hand.sideo When removing gears/sprockets
and chain make notes on position of all washers
and snap rings.
Cover
must
be
removed
to
service
chain, sprockets and pawL (It is not necessary
to remove cover if you are only cleaning and
oiling the chain).. See figures 31 and 32
Removal and reassembly of chain requires that
gear and sprockets
be held in position with
chain and slipped over both shafts, See figure
31.
The pawl, inside ratchet sprocket, has a curved
end (side) and a flat end (side). See figure 31.
When re-assembling ratchet sprocket and pawl,
fill the inside with grease, Re-assemble
the
wheel and turn wheel, if the brushes drive
(rotate) in both directions, the pawl is assembled
incorrectly, remove and flip pawl over° If the
brushes drive (rotate) in one direction the pawl
is assembled correctly,

1,
2,
3,

4

5.

Remove the hopper bag from tawnsweeper,
Brush replacement should be done one brush
at a time_
Tip the sweeper back on housing for ease of
brush replacement,
Do not remove hex bolts
from double brush retainers through
brush
shaft,
Loosen hex bolts and hex lock nuts from single
brush retainers, See figure 33. Slide brush out
of retainers, making note of over-lap bristles
position.
Install new brush, making sure overJap bristles
are positioned the same as before and as shown
in figure 33 (end view of brush)_

RIGHT END VIEW OF
BRUSH

BRUSH
JK-'WROTATION
I
DOUBLE
BRUSH

GEAR!SPROCKE T'

OVERLAP
BRISTLES

COVER_

BRISTLES

BRUSH
ROTATION t
FIGURE 33

FIGURE 31

12

BRUSH
RETAINER

NOTES

13

REPAIR PARTS FOR MODEL 486.240383

OPTIONAL: HITCH SHIELD
MODEL NOr: 486.62718

38"" LAWNSWEEPER

KIT

34

6
/2
58
8O

7

10

1o
_7
19
44

14

REPAIR PARTS FOR MODEL
ER
I0.

t

I

DESCRIPTION

PART NO.
l

23387
23349
23014
23595
2360t
23352
62792

1
1
2
2
2
2
1
4
8
2
2
1
1
1
2
t
1
1

19
20
21
23
24
25
26
27
28

62490
23573
t67!-1
43904
43673
C-9M5732
43655
1650-21
44007

2
2
2
4
t
8
2
4
6

29
3t
32
33

43182
014!-000
43070
1038

4
2
6
2

34

43013

t4

35
36
37

2674-32
43661
43012

2
4
8

38
39

43894
44004

2
4

40
41

44542
43932

2
2

42

43890

1

43

43889

t

44
45
4€
47
4_

44137
43958
43966
43967
43936

4
t
1
t
1

2
3

4
5
6
7
8
9
10
11
12
13
14
15
16
17
18

486.240383

62500
62801
62489
43081
1652-13
1629-56
23574
23580
2_343

_

Sweeper Housing Ass'y.
Adjustment
Rod Ass'y.
Brush Bushing Ass'y.
Washer, 5/t6"
St&
Ball Bearing ,5916 I.D.
Bearing Retainer
Brush Shaft--38"
Brush Retainer-- Double
Brush Retainer-- Single
Wheel Ass'y, Complete
Skirt & Bag Retainer-38"
Height Adjustment
Strap
Hitch Bar
Hitch Bracket
Hopper Mount Arm
Hopper Bag Pivot Rod
Baq Frame Strap--38"
Housing Wheel Drive.
Ass'y, (R_H)
Gear Sprocket Sub, Ass'y,
Dust Cover
Pawl
Sweeper Brush
Skirt
Pop Rivet
Retaining Ring-- 3/4"
Retaining Ring-594"
I.D.
Shim Wash, 596 x 1125
x 025
Hex Bolt 5/t6 x 3/4" Lg*
FI.-Washer .38x 1,25xo06
Washer, 3/8" Std,
Hex bck Nut 3/8-24,
Thd,
Hex Lock Nut I/4-20
Thd_
Hub Cap
Hex Bolt 1/4-20x!,,0"
Lg,*
Hex Bolt 1/4-20 x 3t4"
Lg.* (Gr, 5)
Retaining Ring-- I/2"
Pan Hd,, Screw,#tO-32
x

1" Lg

*Common

hardware

Roller Chain 318 x 112-34
Hex Bolt 3/8-24 x 3-1/4"
Lg. (Gr. 5)
Ratcher Sprocket RoH.11 T. (Not Shown)
Ratcher Sprocket L.H11 1".
'Washer .51 x .990 x .02
Brace Rod
Upper Hopper Tube-R.H
Upper Hopper Tube-LH
Hopper Bag

may be purchased

{ER
_i0.

38"

LAWNSWEEPER

PART NO.

_Y.

DESCRIPTION

49
5O
51
52

43937
43968
43969
43938

t
i
1
2

Wind Screen
Lower Hopper Tube-RoHo
Lower Hopper Tube--L.H.
Hopper Support Rod 34"

55
56
57
58
59

43737
43086
1540-31
1540-107
43001

1
5
2
2
3

60
61
62

43062
43082
R19172410

t
11
1

63
64
65
66

43182
43064
44008
43407

4
4
2
4

67
68
69

1509-90
45088
43346

2
2
6

70
7t
72
73

44230
43662
0142-000
43080

1
12
3
1

74
75
76

23684
44231
43080

1
1

77

62791

't

78
79
80
81
86

43083
43720
43087
1534-8
43978

t
1
2
4
2

Hopper Rope
Spring Lock Washer 5/16"
FL-Washer .78x1_25 x .062
Ft,-Washer .78x1.25 x .031
Hex Bolt 3/8-16 x 1" Lg,
(Gr.5)
Hex Bolt 3/8-16xl-1/2"Lg.*
Hex Lock Nut 3/8-t6 Thd.
Fl.-Washer 17-32 x 1-1/2 x
10 Ga_
Hex Bolt 5/16 x 3/4" Lg.*
Hex Lock Nut 5/16-18 Thd.
FL-Washer ,78 I.D.
Hex Bolt 3/8-16 x 3/4" Lgo
(Gr.5)
Hex Bolt 1/4-20x1-1/4"Lg*
Wheel Bearing
Slotted Trus Hd. Scr.
#10-32 x 5/8" Lg.*
Hitch Pin Spring
Hex Lock Nut#10-32 Thd*
Cotter Pin 1/8"x3/4"
Lg,"
Carriage Bolt 5/16-18 x
3t4" Lg.*
Hitch Pin Bracket
Hitch Pin
Carriage Bolt 5/16_18 x
3f4" Lg_*
Housing Wheel Drive
Ass'y, (LH)
Hex Nut 5/t6-18 Thd.*
Knob, Wing 5/16-18 Thd.
Hex Bolt 3/8-16 x 1-1/4"
Hex Locknut #t0-32 Th&*
Curved Head Boft 1/4-20 x

88
89
90
91
92
93

43943
23368
23400
23331
23354
1095

t
2
I
4
2
6

94

43013

2

95

4335O

1

Grip
Hitch Adjustment
Tube
Spacer t3/32 x 5/8 x 3/16
Hopper Mounting Clamps
Bag Retainer Clevis
Slotted Truss Hd Scn
#10-32 x 1/2" Lg.*
Nut, Lock Hex 1/4-20
Th&*
Carriage Bolt 3/8"-16
x 1"

1

Owner's Manual
Kit, Shield Ass'y.

Lg.

l"Lg

Lg,_

44623
62718

locally.

15

1

38"' HIGH PERFORMANCE
CRAFTSMAN LAWNSWEEPER
Always mention the Model Number' when
or repair parts for your' Lawnsweeper.

requesting

service

All parts listed herein may be ordered from any Sears Service
Center and most Sears stores.

owners
manual

WHEN
ORDERING
REPAIR
FOLLOWING INFORMATION:
OTHE
O THE
eTHE
OTHE

Model No.
486.240383

PARTS,

ALWAYS

GIVE

THE

PART NUMBER
PART DESCRIPTION
MODEL NUMBER
NAME OF MERCHANDISE

If the parts you need are not stocked locally, your order will
be electronically
transmitted
to a Sears Repair Parts Distribution Center for handling.

How to Order
Repair
Parts

LIMITED TWO YEAR WARRANTY
ON CRAFTSMAN LAWR
For two years from date of purchase,
when this Lawnsweeper
is
maintained and lubricated according to the operating and maintenance
instructions in the owner's manual, Seers will repair free of charge any
defect in material or workmanship.
This warranty
-

-

does not cover:

repairs necessary because of operator abuse or negligence,
including the failure to maintain the equipment
according to
instructions
contained
in the owner, s manual;
and
Lawnsweeper used for commercial or rental purposes,

WARRANTY SERVICE tS AVAILABLE BY RETURNING IT TO THENEAREST
SEARS SERVICE CENTER/DEPARTMENT
IN THE UNITED STATES.
This warranty applies only while this product is in use in the United
States.,
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
Sears, Roebuck and Co.. Di817WA, Hoffman Estates, IL 60179

Sears, Roebuck and Co., Hoffman Estates,
FORM NO. 44623

(Rev.

5;93)

IL. 60179 U.S_A.,
PRINTED

IN USA,



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 16
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 4, 0, 0, 13
Create Date                     : Thu Oct 29 04:11:43 2009
Author                          : 
Title                           : 
Subject                         : 

EXIF Metadata provided by EXIF.tools