Crane Payment Innovations ONETRACK RFID system User Manual FLST0310 F
MEI RFID system FLST0310 F
User Manual
2015 Crane Payment Innovations Part No# UG-FLST0310_F 06/15
Functional Grounding
Chassis Grounding
5. General Specifications:
5.1. Electrical Specifications:
Operating Voltage Continuous
Current Maximum
Current
12 V DC/ 24 V DC 1.0 A 3 A
Use only current limiting CSA or UL recognized CLASS 2 Power
Supply.
5.2. Operating Temperature: 0° ~ 50 ° C (32° ~ 122 °F)
5.3. Total Weight: Less than 3.5 Kg (7.72 lb)
5.4. Features: Multi Width 62~85 mm Validator Head
Short Slide Housing
Multi I/O
Dual Operating Voltage
Contactless Reader for Cassette
FLS Cassette with RFID Tag
5.5. Enclosed: Onetrack Enabled Housing Assembly
Validating Head (Part # FLSV-0003)
Mounting Kit ((Part# OPT-MKFLS-HS)
FLS Cassette with RFID Tag (Part# FLSCT0002)
User's Guide
5.6. Applicable Patents:
6229317, 6163034, 7104383, 6057683
CPI | Crane Payment Innovations
2720 Steeles Ave. West, Units 2-3
Concord, ON, Canada, L4K 4S3
Phone: +1 905 303-8874
Toll Free: +1 800 584-2633
Fax: +1 905 303-8875
Website: www.cranepi.com
http://support.cashcode.com
FrontLoad Bill Validator (Onetrack™ Enabled)
FLST0310
User’s Guide
Note:
1) During shipment, switch# 2.3 set to On (Onecheck mode), unless
specified by customer.
2) If Harness not supplied, 4 cables from housing requires to be
installed on 24 Pin.
3) Default Machine No and Location No to be set to “000000”.
2015 Crane Payment Innovations
1. Interface Connector Pin out:
View from the back of the validator
Mating connector CashCode P/N:
o 24 Pin socket: 0100455
o Terminal M1189-2 (JAE P/N DR-SC24-1-7000)
TERMINAL SIGNAL FUNCTION
1 GROUND GROUND BUS
2 RxD-EXT RECEIVE DATA (RS232)
3 TxD-EXT TRANSMIT DATA (RS232)
4 VCC POWER
5 GND GROUND
6 RXD-EXT1 RECEIVE DATA
7 GND-EXT/EXT1 INTERFACE GROUND (RS232)
8 TXD-EXT1 TRANSMIT DATA
9 RS485-A RS485 BUS
10 RS485-B RS485 BUS
11 INP-RXD INPUT SIGNAL
12 INP-TTL1 INPUT SIGNAL
13 POWER- POWER 0V
14 INP-TTL2 INPUT SIGNAL
15 OC-TXD OUTPUT SIGNAL (OPEN-COLLECTOR )
16 OC-OUT1 OUTPUT SIGNAL (OPEN-COLLECTOR )
17 C-LED-BDP /
OC-OUT2 LED CATHODE/ OUTPUT SIGNAL
(OPEN-COLLECTOR )
18 A-LED-BDP LED ANODE
19 POWER+ POWER 12V/24V
20 TXD-BDP TRANSMIT DATA (OPTO)
21 RXD-BDP RECEIVE DATA (OPTO)
22 RST-BDP MASTER RESET (OPTO)
23 GND-BDP INTERFACE GND (OPTO)
24 +12V BDP INTERFACE POWER (OPTO)
We recommend to ground line 1 on the main frame. Also,
Interface ground line must be separate from Power (0 V) ground
2. Typical DIP Switches Setting, Currency and Protocol
Information: Please refer to Software Description.
3. Diagnostics:
This diagnostics chart is for reference only.
Please refer to Software Description for details.
NO OF STATUS LIGHT
FLASHES ERROR DESCRIPTION
HARDWARE
1 RED ON BLACK CASSETTE IS REMOVED FROM BILL VALIDATOR
2 RED ON BLACK AN ERROR OCCURRED DURING CPU EXCHANGE WITH MAGNETIC
BOARD
3 RED ON BLACK CASSETTE IS FULL
4 RED ON BLACK MECHANICAL JAM IN THE CASSETTE OR STACKER MOTOR FAILURE
5 RED ON BLACK FAILURE OF DIELECTRIC SENSORS
6 RED ON BLACK FAILURE OF OPTICAL SENSORS
7 RED ON BLACK FAILURE OF INDUCTIVE SENSORS
8 RED ON BLACK FAILURE OF TRANSPORTING MOTOR
9 RED ON BLACK SPEED OF TRANSPORTING MOTOR IS TOO FAST
10 RED ON BLACK FAILURE IN ALIGNMENT MECHANISM
11 RED ON BLACK BILL PATHWAY IS NOT EMPTY
12 RED ON BLACK BILL JAMMED IN ENTRY SLOT OF THE CASSETTE. NO CREDIT GIVEN
13 RED ON BLACK OVERLOAD OF TRANSPORT MOTOR
14 RED ON BLACK SYSTEM ERROR
SOFTWARE
1 GREEN ON RED UNABLE TO WRITE PROGRAM MEMORY
2 GREEN ON RED FIRMWARE INTEGRITY ERROR
3 GREEN ON RED WRONG MEMORY CARD
4 GREEN ON RED SECURITY ERROR
Onetrack
FLICKER X 1 CASH BOX IS HOT OR MACHINE# IS MISMATCH
FLICKER X 2 ONETRACK CASH BOX / ANTENNA BOARD MODULE ERROR
4. FCC and IC Information:
FCC ID # QP8ONETRACK.
IC # 1297A-ONETRACK.
Changes or modifications not approved by the manufacturer could void the user’s authority
to operate the equipment.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference.
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage.
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference.
(2) this device must accept any interference received, including interference that
may cause undesired operation.
7
16
12
13 18
19 24