Crane Payment Innovations ONETRACK RFID system User Manual FLST0310 F
MEI RFID system FLST0310 F
User Manual
5. General Specifications: 5.1. Electrical Specifications: Operating Voltage 12 V DC/ 24 V DC Continuous Current 1.0 A Maximum Current 3A Use only current limiting CSA or UL recognized CLASS 2 Power Supply. 5.2. Operating Temperature: 0° ~ 50 ° C (32° ~ 122 °F) 5.3. Total Weight: Less than 3.5 Kg (7.72 lb) FrontLoad Bill Validator (Onetrack™ Enabled) FLST0310 User’s Guide Chassis Grounding Functional Grounding 5.4. Features: Multi Width 62~85 mm Validator Head Short Slide Housing Multi I/O Dual Operating Voltage Contactless Reader for Cassette FLS Cassette with RFID Tag 5.5. Enclosed: Onetrack Enabled Housing Assembly Validating Head (Part # FLSV-0003) Mounting Kit ((Part# OPT-MKFLS-HS) FLS Cassette with RFID Tag (Part# FLSCT0002) User's Guide 5.6. Applicable Patents: 6229317, 6163034, 7104383, 6057683 CPI | Crane Payment Innovations 2720 Steeles Ave. West, Units 2-3 Concord, ON, Canada, L4K 4S3 Phone: +1 905 303-8874 Toll Free: +1 800 584-2633 Fax: +1 905 303-8875 Website: www.cranepi.com http://support.cashcode.com 2015 Crane Payment Innovations Note: 1) During shipment, switch# 2.3 set to On (Onecheck mode), unless specified by customer. 2) If Harness not supplied, 4 cables from housing requires to be installed on 24 Pin. 3) Default Machine No and Location No to be set to “000000”. Part No# UG-FLST0310_F 06/15 12 18 View from the back of the validator Mating connector CashCode P/N: 24 19 o 24 Pin socket: 0100455 o Terminal M1189-2 (JAE P/N DR-SC24-1-7000) TERMINAL SIGNAL FUNCTION GROUND GROUND BUS RxD-EXT RECEIVE DATA (RS232) TxD-EXT TRANSMIT DATA (RS232) VCC POWER GND GROUND RXD-EXT1 RECEIVE DATA GND-EXT/EXT1 INTERFACE GROUND (RS232) TXD-EXT1 TRANSMIT DATA RS485-A RS485 BUS 10 RS485-B RS485 BUS 11 INP-RXD INPUT SIGNAL 12 INP-TTL1 INPUT SIGNAL 13 POWER- POWER 0V 14 INP-TTL2 INPUT SIGNAL 15 OC-TXD OUTPUT SIGNAL (OPEN-COLLECTOR ) 16 OC-OUT1 C-LED-BDP / OC-OUT2 A-LED-BDP OUTPUT SIGNAL (OPEN-COLLECTOR ) LED CATHODE/ OUTPUT SIGNAL (OPEN-COLLECTOR ) LED ANODE 17 18 19 POWER+ POWER 12V/24V 20 TXD-BDP TRANSMIT DATA (OPTO) 21 RXD-BDP RECEIVE DATA (OPTO) 22 RST-BDP MASTER RESET (OPTO) 23 GND-BDP INTERFACE GND (OPTO) 24 +12V BDP INTERFACE POWER (OPTO) We recommend to ground line 1 on the main frame. Also, Interface ground line must be separate from Power (0 V) ground 2. Typical DIP Switches Setting, Currency and Protocol Information: Please refer to Software Description. 2015 Crane Payment Innovations Please refer to Software Description for details. NO OF STATUS LIGHT FLASHES 1 RED ON BLACK 2 RED ON BLACK HARDWARE 13 3. Diagnostics: This diagnostics chart is for reference only. SOFTWARE Onetrack 1. Interface Connector Pin out: ERROR DESCRIPTION CASSETTE IS REMOVED FROM BILL VALIDATOR AN ERROR OCCURRED DURING CPU EXCHANGE WITH MAGNETIC BOARD 3 RED ON BLACK 4 RED ON BLACK 5 RED ON BLACK 6 RED ON BLACK 7 RED ON BLACK 8 RED ON BLACK 9 RED ON BLACK 10 RED ON BLACK 11 RED ON BLACK 12 RED ON BLACK 13 RED ON BLACK 14 RED ON BLACK CASSETTE IS FULL MECHANICAL JAM IN THE CASSETTE OR STACKER MOTOR FAILURE FAILURE OF DIELECTRIC SENSORS FAILURE OF OPTICAL SENSORS FAILURE OF INDUCTIVE SENSORS FAILURE OF TRANSPORTING MOTOR SPEED OF TRANSPORTING MOTOR IS TOO FAST FAILURE IN ALIGNMENT MECHANISM BILL PATHWAY IS NOT EMPTY BILL JAMMED IN ENTRY SLOT OF THE CASSETTE. NO CREDIT GIVEN OVERLOAD OF TRANSPORT MOTOR SYSTEM ERROR 1 GREEN ON RED UNABLE TO WRITE PROGRAM MEMORY 2 GREEN ON RED FIRMWARE INTEGRITY ERROR 3 GREEN ON RED WRONG MEMORY CARD 4 GREEN ON RED SECURITY ERROR FLICKER X 1 CASH BOX IS HOT OR MACHINE# IS MISMATCH FLICKER X 2 ONETRACK CASH BOX / ANTENNA BOARD MODULE ERROR 4. FCC and IC Information: FCC ID # QP8ONETRACK. IC # 1297A-ONETRACK. Changes or modifications not approved by the manufacturer could void the user’s authority to operate the equipment. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference. (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage. (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Oleksandr Create Date : 2015:06:04 12:06:43-04:00 Modify Date : 2015:06:04 12:06:43-04:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Title : Microsoft Word - FLST0310_F.doc Creator : Oleksandr Creator Tool : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 9.5.5 (Windows) Document ID : uuid:fd644c4d-0d9d-46cc-89d8-afb529720546 Instance ID : uuid:1fa9dcd4-25be-4607-b7ce-b0da76e6f626 Page Count : 2EXIF Metadata provided by EXIF.tools