Crystal Video Technology 306020180409 Wireless Video Transmission System User Manual
Shenzhen Crystal Video Technology Co.,LTD. Wireless Video Transmission System
User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3823605 |
| Application ID | mWWe/bG0ky7mokTDEdM8qg== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 298.11kB (3726314 bits) |
| Date Submitted | 2018-04-20 00:00:00 |
| Date Available | 2018-04-20 00:00:00 |
| Creation Date | 2018-04-13 03:07:10 |
| Producing Software | Corel PDF Engine Version 14.0.0.653 |
| Document Lastmod | 2018-04-13 03:07:10 |
| Document Title | å¤©æ¼”æ— çº¿å›¾ä¼ ä¸è‹±æ–‡å¿«é€Ÿæ“作指å—折页-认è¯ä¸“用 |
| Document Creator | CorelDRAW |
| Document Author: | Administrator |
产品及配件自购买之日起保修一年 天演无线图传 BeamLink-Quad ONE-YEAR LIMITED WARRANTY 深圳市视晶无线技术有限公司 BeamLink-Quad Wireless Transmission System 深圳市宝安中心区宝源路F518时尚创意园F10-13栋 邮编：518102 电话：+86-755-26716688 E-mail：Sales@cv-hd.com 服务热线：400-6262-963 传真：+86-755-29188427 E-mail：Marketing@cv-hd.com 快速使用指南 Quick Start Guide Model:3060 Version:1.0 感谢您选用CVW公司的专业级无线高清传输产品， 在使用产品前，请仔细阅读本使用说明 2. 请将发射机通过机身底部的螺母孔或侧面V扣固定到距离 地面1.5~2米处的位置。多台发射机同时工作时请保证 发射机之间至少间距1米。( 如下图所示） 2. 请将接收机放置在距离地面1.5~2米高处。接收机可以 立放、卧放，并能通过机身底部的螺母孔或侧面V扣进 行固定安装。立式摆放前请先装上随附的底座。 ( 如下图所示） B:立式摆放 此产品利用低延时H264编解码方案和5G WIFI方案， 完成四路高清视频的无线传输，四路信号只占用一路无线信道， 接收端将四路SDI或HDMI高清视频信号传到切播台。 A:卧式摆放 间距>1米 间距>1米 距离地面>1.5-2米 空旷环境下传输距离500米 4台发射机和接收机的4路视频输出口是一一对应的， OLED屏上显示设备号1的发射机，解码后的视频将通过 接收机背面丝印1处的视频口输出，其余类推。 接收机放置在距离 地面1.5~2米高处 步骤四 产品按键操作 安装底座 支持tally功能（接收机被低电平触发后， 发射机输出高电平信号） 发射机和接收机均支持电池供电 超低延时技术，可无缝对接各种类型的切播台 3. 请将发射机和摄像机之间的高清视频线连接好。 ( 如下图所示） 使用情形 利用机身底部的螺母孔 用2颗螺母进行固定安装 3. 请将接收机和导播台或监视器之间的高清视频线连接好。 00:00:00 更换设备后 请重新对码 HDMI HDMI HDMI HDMI输出 HDMI HDMI HDMI输出 HDMI HDMI输出 HDMI HDMI输出 产品包装内随附以下物品： 近距离使用 时请使用 低增益模式 HDMI 物品清单 电源适配器 *1 安装底座 *1 说明：发射机自带Sony NP-F电池座并已预装V扣连接件； 接收机上已预装电池扣板和V扣连接件。 步骤二 接收机准备 SDI 天线 *4 SDI 接收机 *1 发射机 接收机 -- 通过短按【CH/WPS】按键可 在11个工作频点间循环切换 接收机切换工作频点后， 接收机和发射机的OLED屏都会显示当前频点号 长按【LNA ON/OFF】 按键3秒进行高低增益 模式切换 4. 接收机可以通过电池扣板外挂V字型锂电池供电，也可以 通过卡侬口外接随附的电源适配器供电。如果同时接好 了两种供电方式，将优先使用锂电池供电，电池耗尽后 将自动切换至电源适配器供电。 发射机和接收机切换至低增益模式后，OLED屏上都会 显示“L”字符。如果切换回高增益模式该字符会消失。 长按【CH/WPS】 按键3秒启动对码 长按【CH/WPS】 按键3秒启动对码 发射机和接收机在对码过程中，OLED屏上都会一直 显示”WPS“字符串，对码结束后该字符串消失。 编码板在重启过程中， 该发射机的OLED屏上会 一直显示“RESET” 字符串，重启结束后该 字符串消失 接收机重启 某一路 解码板 -- 步骤一 发射机准备 电源 接收机切换 OLED显示 方向 -- 锂电池 本系统支持Tally功能，请将发射机和接收机端的Tally线 连接好。当接收机被低电平触发后，发射机将输出高电 平信号。 -- 首先通过短按【RESET】 按键在1、2、3、4间循环 选择要重启的那一路解码板， 然后长按【RESET】 按键3秒确定重启。 解码板在重启过程中， 接收机的OLED屏上会一直 显示“RESET”字符串， 重启结束后该字符串消失 1. 请按图示将天线安装至接收机的天线接口， 并呈扇形摆放。( 如下图所示） 1. 请按图示将天线安装至发射机的天线接口， 呈扇形摆放。( 如下图所示） 长按【LNA ON/OFF】 按键3秒进行高低增益 模式切换 长按【RESET】按键3秒 重启该发射机的编码板 发射机重启 编码板 HDMI HDMI输入 SDI SDI输入 电源线 *4 SDI 1/4英寸 螺母杆连接件 *4 SDI输出 SDI输出 SDI输出 SDI SDI输出 天线 *16 遇到干扰源 请切换 工作频点 ( 接收机支持4个SDI输出和4个HDMI输出 ) 产品安装简单、操作便捷、应用灵活，免除多机位布线烦恼。 发射机 *4 请依次打开发射机、接收机和其它关联设备的电源开关， 上电后发射机和接收机的OLED屏点亮，发射机的指示灯 亮红灯。发射机与接收机进行WiFi连接时，发射机指示灯 切换至黄灯闪烁，WiFi连接成功后黄灯长亮，稍等片刻就 能在接收机连接的显示终端观看到实时图像。从产品上 电到显示实时图像预计花费1分半钟。 间距>1米 产品特色 支持四路HDMI和SDI输出，分辨率最高1080P/60 www.cv-hd.cn 步骤三 产品开机 短按【LNA ON/OFF】按键， 接收机的OLED将进行横屏和 竖屏显示切换。 www.cv-hd.com Thank you for buying CVW product--BeamLink-Quad, the product adopt the low latency H264 coding-anddecoding scheme and 5G WiFi solution. the 4 Transmitters-to-1 Receiver wireless HD video transmission system. Please read the instructions carefully before using the product. 2. Please fix the transmitter via the screw at the bottom or the V-mount at the back, and place it at a height of around 1.5 to 2 meters above floor. Please make sure that the distance between each transmitter is more than 1 meter. 2. Please place the receiver at a height of around 1.5 to 2 meters above floor. Receiver can be placed in vertical or horizontal positions, and can be fixed via the screw at the bottom or V-mount at the back. Please install the affiliated metal stand before placing the receiver in vertical position. B: Vertical placement A: Horizontal placement Distance> 1 m Distance> 1 m There is a one-to-one correspondence between four transmitters and four video output interfaces of the receiver, that is to say, the video transmitted by the transmitter which shows No. 1 on its OELD screen will be also output from the video out interface marked No. 1 and can deduce the rest 3 transmitters from this. Place the receiver at a height of around 1.5 to 2 meters above floor. install the affiliated metal stand Description of buttons operation Usage Scenario 3. Please connect the transmitter and camera with SDI or HDMI cable. 3. Please connect the receiver and video switch console or monitor with SDI or HDMI cable. HDMI HDMI HDMI Out 00:00:00 HDMI Out Transmitter Receiver -- Short press button “CH/WPS” to switch among 11 channels circularly. After switching the channel, the OLED screen of transmitter and receiver will both display current working frequency. Long press button “LNA ON/ OFF” for 3 seconds to switch high or low gain mode. Long press button “LNA ON/ OFF” for 3 seconds to switch high or low gain mode. After switching into low gain mode both on transmitter and receiver sides, the OLED screen will display an “L” letter. If switching back to high gain mode, the letter will disappear. HDMI HDMI HDMI Out HDMI The following items are included in the product package: HDMI PACKING LIST Switching to a different channel when there is interference. Please choose low gain mode when works in short distance. HDMI HDMI Out HDMI Simple installation; convenient operation; flexible application; eliminate the hassel of running wires across multi-camera positions. Transmitter at a height of Support 4 channels video input & output through SDI or HDMI interface. The system can be connected seamlessly to most popular video switch consoles. around 1.5 to2 meters above floor. 8Mbps date rate for each video channel, support 4 channels video transmission simultaneously in up to 500 meters range with 150mS latency; Please turn on transmitter, receiver and other related devices in turn. After powering on, the OLED panel on the transmitter and the receiver will be lit up, and the status light of transmitter will be lit red. When transmitter and receiver are on connecting mode, the status light of transmitter will turn to flicker in yellow. When the connection is successful, the status light of transmitter will be on yellow steadily, then you will get live image at the receiver side. It will take about 90 seconds from powering up the product to the live image displaying. Distance> 1 m PRODUCT FEATURES Support 4 Tx-to-1 Rx; tally function; support 4 channels HD video transmission simultaneously in ONLY 1 RF channel; Power up and start to use Receiver * 1 piece Antenna * 4 pieces Power adapter*1 piece Metal Stand*1 piece Notice: The transmitter comes with the Sony NP-F type battery plate and has preassembled V-mount connector. The receiver has preassembled battery plate and v-mount connector. HDMI HDMI In SDI SDI In Power supply cable *4 pieces SDI 1/4 inch screw & nut connector*4 pieces SDI Antenna * 16 pieces Long press button “CH/WPS” for 3 seconds to start paring. Long press button “CH/WPS” for 3 seconds to start paring. When transmitter and receiver are in the process of paring, the OLED screen will display character string “WPS”, and the character string will disappear after paring is successful. Long press button “RESET” for 3 seconds to reset the video encoder of transmitter. SDI Transmitter * 4 pieces Please re-pair the kits after you replace receiver or transmitter SDI SDI Out SDI Out SDI Out SDI Out 4. The receiver can be powered by both the V-mount battery and DC-IN port via the affiliated power adapter. If the mentioned two types of powersupply are connected at the same time, the lithium battery should be prioritized in power supplying, and the battery will switch to the power adapter for power supplying automatically after the battery power is exhausted. Reset video encoder When the video encoder is on resetting, the OLED screen of this transmitter will keep displaying the character string “RESET”, and the character string will disappear after resetting is finished. Receiver Installation 1. Please install all the antennas on the receiver, and make them in a fan shape as shown in the picture. Transmitter Installation Reset specific video decoder on receiver. -- Switch OLED display direction of receiver -- Power 1. Please install all the antennas on the transmitter and make them in a fan shape as shown in the picture. Li-battery This system supports tally function. When the receiver is activated by low-level current, the transmitter will output high-level current signal. -- First, short press button“RESET” to choose the video decoder which you need to reset from the symbol as 1, 2, 3, 4 on OLED screen of receiver , then long press button “RESET” for 3 seconds to confirm resetting. When video decoder is in the process of resetting, the OLED screen of receiver will keep displaying character string “RESET”, and the character string will disappear after esetting is finished. Short press button “LNA ON/OFF” and the OLED display direction of receiver will be switching between horizontal and vertical modes. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 4 Create Date : D:20180413030710Z Modify Date : D:20180413030710Z Producer : Corel PDF Engine Version 14.0.0.653 Author : Administrator Creator : CorelDRAW Title : 天演无线图传中英文快速操作指南折页-认证专用EXIF Metadata provided by EXIF.tools