CyberTAN Technology WM821M Wireless 802.11N DUAL BAND MINI PCI MODULE User Manual rev 0702

Download:
Mirror Download [FCC.gov]
Document ID	811598
Application ID	MAZNw7ks+UA4vFrE0wsxjw==
Document Description	User manual rev
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	82.18kB (1027240 bits)
Date Submitted	2007-07-04 00:00:00
Date Available	2007-07-04 00:00:00
Creation Date	2007-07-02 19:12:14
Producing Software	AFPL Ghostscript 8.54
Document Lastmod	2007-07-03 09:58:47
Document Title	User manual - rev 0702
Document Creator	PDFCreator Version 0.9.2
Document Author:	Joy

WM821-M MiniPCI Module
WM821-M
Wireless 802.11N dual-band mini PCI module
User Manual
Rev 0.1
WM821-M MiniPCI Module
Federal Communication Commission Interference
Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from thatto which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
WM821-M MiniPCI Module
Introduction
—
interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the
radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor
usage only
IEEE 802.11b or 802.11g operation of this product in the U.S.A.
is firmware-limited to channels 1 through 11.
This device is intended only for OEM integrators under the
following conditions:
1) The antenna must be installed such that 20 cm is maintained
between the antenna and users, and
2) The transmitter module may not be co-located with any other
transmitter or antenna,
3) For all products market in US, OEM has to limit the operation
channels in CH1 to CH11 for 2.4G band by supplied firmware
programming tool. OEM shall not supply any tool or info to
the end-user regarding to Regulatory Domain change.
As long as 3 conditions above are met, further transmitter
test will not be required. However, the OEM integrator is still
ii
Preface
responsible for testing their end-product for any additional
compliance requirements required with this module installed
(for example, LVD TV… etc.).
IMPORTANT NOTE: In the event that these conditions can
not be met (for example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be
used on the final product. In these circumstances, the OEM
integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling
This transmitter module is authorized only for use in device
where the antenna may be installed such that 20 cm may be
maintained between the antenna and users. The final end
product must be labeled in a visible area with the following:
“Contains FCC ID: N89-WM821M”.
Manual Information To the End User
The OEM integrator has to be aware not to provide
information to the end user regarding how to install
or remove this RF module in the user’s manual of
the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
iii
WM821-M MiniPCI Module
Introduction
—
Canadian Regulatory Notice
This device complies with RSS-210 of the Industry Canada
Rules. Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired operation of the device
Caution:
The device for the band 5150-5250 MHz is only for indoor usage
to reduce potential for harmful interference to co-channel mobile
satellite systems.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the
radiator and your body.
Industry Canada Interference Statement
The device for the band 5150-5250 MHz is only for indoor usage
to reduce potential for harmful interference to co-channel mobile
satellite systems;
The maximum antenna gain permitted (for devices in the bands
5250-5350 MHz and 5470-5725 MHz) to comply with the e.i.r.p.
limit; and
The maximum antenna gain permitted (for devices in the band
5725-5825 MHz) to comply with the e.i.r.p. limits specified for
iv
Preface
point-to-point and non point-to-point operation as appropriate, as
stated in section A9.2(3).
In addition, users should also be cautioned to take note that
high-power radars are allocated as primary users (meaning they
have priority) of the bands 5250-5350 MHz and 5650-5850 MHz
and these radars could cause interference and/or damage to LELAN devices.
Note: The WM821-M has disable the 5600-5650M band by
S/W to avoid 5600-5650M band for IC certification
WM821-M MiniPCI Module
Introduction
—
Table of contents
Introduction
Hardware installation
Using the Wireless Utility
vi
WM821-M MiniPCI Module
Chapter 1
Introduction
Thank you for using the Wireless MiniPCI Module. The WM821M is a dual-band, quad-mode wireless network adapter that
works on all the frequencies allocated for WLAN operation everywhere in the world. It is in compliance with the Draft
IEEE802.11n standard in a 2x3 MIMO configuration. It also
complies with the IEEE 802.11a, 802.11g, and 802.11b standards. WM821-M features the compactness and high bus
speed of the Mini PCI specifications which gives users of laptops, notebooks, tablet PCs, and other mobile computing
devices transparent Internet access anywhere in the world
through any Wi Fi network without software changes or additional hardware.
Able to provide greater than 100Mbps real world throughput
using high-speed spatial multiplexing modes, the WM821-M
provides the freedom to work as you wish, wherever you wish,
using whatever kind of application you wish to use. The adapter
installs directly in any host device with a Mini PCI slot: just plug
it in and you’re ready to access local resources and/or the Internet at the highest speed the WLAN, the location, and the host
computer can provide. It is ready to work “out of the box” in any
embedded device or in any computer running Microsoft® Windows 2000, or XP (TBD). The WM821-M Mini PCI Card is truly
a “must-have” for every productivity-sensitive laptop, notebook,
WM821-M MiniPCI Module
—Introduction
or tablet PC user and any bandwidth-sensitive embedded design..
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
mPCI 32 interface.
Draft IEEE 802.11n compatible.
Backward compatible with IEEE 802.11a/b/g standard.
Wire-free access to networked resources from anywhere
beyond the desktop.
Delivers data rates up to 300 Mbps.
802.11n: Dynamically shifts among 130, 117, 104, 78, 52,
39, 26 and 13Mbps in a 20MHz bandwidth and 300, 243,
216, 162, 108, 81, 54 and 27Mbps in a 40MHz bandwidth,
based on signal strength, for maximum availability and reliability of connection.
802.11a/g: Dynamically shifts between 54, 48, 36, 24, 18,
12, 9 and 6 Mbps network speed, based on signal strength,
for maximum availability and reliability of connection.
802.11b: Dynamically shifts between 11M, 5.5M, 2M, and 1
Mbps network speed, based on signal strength, for maximum availability and reliability of connection.
Supports 802.11h (DFS) power adjustment.
Allows users move between Access Points without resetting the connection reconfigurations.
Three ultra-mini connectors with for diversity antennae.
Uses 2.4GHz and 5GHz frequency band, complying with
regulatories worldwide
Supports most popular operating systems: Window
2000/XP. Linux support is also available.
Ensures great security by providing the 64/128 bits Wired
Equivalent Privacy (WEP) and WiFi Protected Access
(WPA) defined in the IEEE standard.
WPA support with Funk client. Radius clients in EAP-TLS,
EAP, TTLS, EAP-LEAP, EAP, PEAP.
WPA2, WMM-compliant.
—Introduction
WiFi-Protected Setup(WPS)-supportedWhat
is Wireless LAN?
Wireless Local Area Network (WLAN) systems offer a great
number of advantages over traditional wired systems. WLANs
are flexible and easy to setup and manage. They are also more
economical than wired LAN systems.
Using radio frequency (RF) technology, WLANs transmit and
receive data through the air. WLANs combine data connectivity
with user mobility. For example, users can roam from a conference room to their office without being disconnected from the
LAN.
Using WLANs, users can conveniently access shared information, and network administrators can configure and augment
networks without installing or moving network cables.
WLAN technology provides users with many convenient and
cost saving features:
•
Mobility: WLANs provide LAN users with access to realtime information anywhere in their organization, providing
service opportunities that are impossible with wired networks.
•
Ease of Installation: Installing is easy for novice and expert users alike, eliminating the need to install network
cables in walls and ceilings.
•
Scalability: WLANs can be configured in a variety of topologies to adapt to specific applications and installations.
Configurations are easily changed and range from peerto-peer networks suitable for a small number of users to
WM821-M MiniPCI Module
—Introduction
full infrastructure networks of thousands of users roaming
over a broad area.
Chapter 2
Hardware installation
This chapter covers how to installing the Wireless MiniPCI
Module in your embedded system.
Hardware description
The Wireless MiniPCI Module has a standard MiniPCI interface for attaching to the MiniPCI connector on embedded
system.
And this module has IPEX connector to connect to external
antenna.
Outlook
Following is the MiniPCI module outlook
WM821-M MiniPCI Module
Hardware installation
Figure 1: MiniPCI module outlook
—
Chapter 3
Using the Wireless Utility
This module also come with a wireless utility, following describe
how to use the utility.
Configuration Utility
The Client Card Configuration Utility allows configuration of WM821-M high
throughput client cards through the following tabs:
•
Network Status—displays the status of the network to which the
user is connected. The Configuration Utility
initializes on this page.
•
Profile Manager—displays the current profiles and allows the user to set
attributes for network type, security options, and
protocols, as well as create/modify/delete profiles.
•
Site Survey—displays site survey information.
•
Statistics—displays the statistics of the current session.
•
Advanced—used to set protocol parameters.
•
AutoLink—to set AutoLink connection
•
Admin—used to import and export profiles.
3.1 Network Status Tab
The Network Status tab displays the status of the network. When the Wireless
client card Configuration Utility initializes, it displays the Network Status tab.
WM821-M MiniPCI Module
Wireless Utility
—Using the
Figure 2 :Network Status tab
3.1.1 Select Profile
The Select Profile section displays the name of the profile in use. Additional information about the profile is provided in the Profile Manager.
Select one of the profiles previously defined by clicking the down arrow and highlighting a profile from the pull-down list.
Figure 3: Select Profile Section
Appendix B Error Messages of Enabler Program
Figure 3: Select Profile
Profiles are created, modified, and deleted through the ProfileManager.
Note
This feature is disabled when Windows Zero Configuration Utility is enabled.
3.1.2 Link Information
The Link Information section contains the current information about the wireless
connection. Figure 4: Link Information Section
Figure 4: Link Information Section
WM821-M MiniPCI Module
Wireless Utility
—Using the
Table 1:Link Information
Field
Description
Status
Status of the wireless network connection:
• Card Unplugged Client card is not plugged in, or client card
is plugged in but not recognized.
• Connected
Client card is plugged in and connected to a wireless network.
• No Connection
Client card is plugged in, but no wireless connection.
• No Radio
Client card is plugged in, but the radio is turned off. Clear the
Radio Off check box to turn the radio on.
• Scanning for Scanning for available APs and wireless stations in the area.
Network SSID
Network Type
10
Network SSID label (i.e., Network Name). The Network Name
is a text string of up to
32 characters.
Type of environment connected to: • Infrastructure Mode In
this mode, wireless clients send and receive information
through APs. When a wireless client communicates with another, it transmits to the AP. First the AP receives the
information and rebroadcasts it, then other devices receive the
information. The APs are strategically located within an area to
provide optimal coverage for wireless clients. A large WLAN
uses multiple APs to provide coverage over a wide area. APs
can connect to a LAN through a wired Ethernet connection.
APs send and receive information from the LAN through the
wired connection.
Appendix B Error Messages of Enabler Program
Network BSSID
Network Basic Service Set Identifier. The BSSID is a 48-bit
identity used to identify a particular BSS within an area. In Infrastructure BSS networks, the BSSID is the MAC
Security
Tx/Rx Rates
Reports the type and level of security set. The security level is
set through the Profile
Setting of the Profile Manager tab. Configure security settings
also through the Site
Survey tab when connecting to a network.
Current Tx Rate and Rx Rate of the channel being monitored.
3.1.3 Signal Strength / Wireless Mode Indicator
The color-coded Signal Strength bar displays the signal strength of the last packet
received by the client card.
Figure 5: Signal Strength
11
WM821-M MiniPCI Module
Wireless Utility
—Using the
Signal strength is reported as a percentage. A signal in the red indicates a bad connection. A signal in the green indicates a good connection.
The Wireless Mode indicator shows the data rates the client card operates. There
are three modes:
• 802.11a
• 802.11b
• 802.11g (backward compatible to 802.11b)
3.1.4 Internet Protocol (TCP/IP)
The Internet Protocol specifies the format of packets, also called data grams, and
the addressing scheme. Most networks combine IP with a higher-level protocol
called TCP, which establishes a virtual connection between a destination and a
source.
Figure 6:Internet Potocol Section
Table 2 Internet Protocol Section Description
Field
Description
DHCP Option
Dynamic Host Configuration Protocol. Either enabled or dis-
12
Appendix B Error Messages of Enabler Program
abled.
IP Address
Subnet Mask
Default Gateway
An identifier for a computer or device on a TCP/IP network. The
format of an IP address
is a 32-bit numeric address written as four numbers separated
by periods. Each number
can be 0 to 255.
A mask used to determine what subnet an IP address belongs
to. An IP address has two
components, the network address and the host address. The
first two numbers represent the Class B network address, and
the second two numbers identify a particular host on
this network.
The default node on a network that serves as an entrance to
another network. In enterprises, the gateway is the computer
that routes the traffic from a workstation to the outside network
that is serving the Web pages. In homes, the gateway is the
ISP that connects the user to the Internet.
3.1.5 Actual Throughput Performance
This section of the Network Status tab displays the Current Tx Rate and the Current Rx Rate of the channel being monitored.
Figure 7: actual throughput diagrams
Note
13
WM821-M MiniPCI Module
Wireless Utility
—Using the
These are actual throughput diagrams (without the WLAN overhead delivered by
the client card).
3.1.6 Radio On/Off Check Box
Selecting the Radio Off check box turns off the radio. Clearing the check
box turns on the radio. Figure 8: Radio On/Off Check Box
Figure 8:Radio On/Off Check Box
Another way to turn the radio on or off is to right-click the Configuration Utility icon
in System Tray and select Turn Radio Off to turn the radio off. When the radio is
off, select Turn Radio On to turn the radio back on.
Figure 9: Radio On/Off in the System Tray
The system hot key Alt+F2 can also be used to turn the radio on/off.
When the radio is off, there is no radio activity, and the following tabs are disabled:
14
• Profile Manager
• Site Survey
• Statistics
Appendix B Error Messages of Enabler Program
• Advanced
• AutoLink
Note
This feature is disabled when Windows Zero Configuration Utility is enabled.
3.2 Profile Manager Tab
The Profile Manager tab displays the profiles available and allows you to create,
modify, and delete profiles.
15
WM821-M MiniPCI Module
Wireless Utility
—Using the
Figure 10: Figure 14: Profile Manager Tab
Note
The Profile Manager tab is not accessible when Windows Zero
Configuration Utility is enabled.
16
Appendix B Error Messages of Enabler Program
PROFILE MANAGER—PROFILE LIST
The section on the left side of this tab lists all of the profiles available. Highlighting a
profile selects it. If the check box next to the profile is selected, that profile is used
in auto-configuration mode when the link is lost. If it is not selected, that profile is
excluded in auto-configuration. The buttons associated with this window are as follows.
Table 3: Profile List Section Description
Button
Description
Apply Profile
Applies the profile selected.
Apply the profile by double-clicking the desired profile.
Move Up / Down
Moves the list up and down in the window.
Delete
Deletes a profile
Create
Creates a profile
Save
Saves changes made to a selected profile
PROFILE MANAGER—PROFILE SETTING The Profile Settings are used to
set, modify, and display information about the profile selected in the Profile List
section. The information is divided into three tabs:
• Network Info
• Security
• Protocol
3.2.1 Profile Setting—Network Info Tab
The Profile Manager initially displays the Network Info tab.
17
WM821-M MiniPCI Module
Wireless Utility
Figure 11: Network Info Tab (Infrastructure Network)
The Network Info tab fields are as follows.
Table 4:: Network Info Tab Description
Field
Description
Profile Name
Name of profile selected
Network SSID
Network SSID label
18
—Using the
Appendix B Error Messages of Enabler Program
Network Type
• Infrastructure When an Infrastructure network is selected,
the Profile Setting displays the Wireless Mode field.
Wireless Mode
• Auto
Connects to 802.11a network, 802.11g network, or 802.11b
network (Infrastructure network only).
• 802.11a
Connects to 802.11a only.
• 802.11g Connects to either 802.11g network or 802.11b
network.
• 802.11b
Connects to 802.11b network only.
802.11n Network
Channel Width
Guard Interval
Extension Channel
Antenna Selection
Enables/disables draft-802.11n/EWC functionality.
If enabled, the Modulation and Coding Scheme (MCS) index
and 802.11n options can
be configured.
Sets the channel bandwidth. Available options are Auto, 20
MHz, and 40 MHz.
The default is Auto.
Sets the Guard Interval. Available options are Auto, Standard,
and Short.
The default is Auto.
Sets the extension channel mode when bandwidth is 40 MHz.
Available options are
Auto, None, Lower, and Upper. The default is Auto.
Sets the antenna selections. Available options are Auto, Antenna A, Antenna B, 2 by 2,
and 2 by 3. The default is Auto.
19
WM821-M MiniPCI Module
Wireless Utility
—Using the
3.2.2 Profile Setting—Security Tab
Clicking the Security tab displays
the following security options:
• Authentication Mode
• Encryption Mode (Security off, WEP, TKIP, and AES)
• WEP Key Setting (Passphrase Key or Authentication Protocol)
Figure 12:: Security tab
3.2.2.1 Non-EAP Authentication Modes
The WM821-M Configuration Utility currently supports the following non-EAP authentication modes:
• Open System—Open Authentication (no key or a pre-shared WEP key is
required).
• Shared Key—Shared Authentication (a pre-shared WEP key is required)
• Auto Switch—Auto Select Authentication modes (Open System or Shared
Key, WEP key required)
20
Appendix B Error Messages of Enabler Program
• WPA-PSK—WPA Pre-Shared Key
• WPA2-PSK—WPA2 Pre-Shared Key
3.2.2.2 EAP Authentication Modes
The WM821-M Configuration Utility currently supports the following EAP authentication modes:
• 802.1x (TLS/PEAP)
• WPA (TLS/PEAP/LEAP)
• WPA2 (TLS/PEAP/LEAP)
• CCX (LEAP)
3.2.2.2.1 WPA-PSK/WPA2-PSK SUPPORT
In Infrastructure mode, if WPA-PSK/WPA2-PSK is selected as the Authentication
Mode, the encryption method AES or TKIP can be selected.
Figure 13: Security selection
21
WM821-M MiniPCI Module
Wireless Utility
—Using the
Figure 14: Security Tab—WPA-PSK/WPA2-PSK with TKIP
Enter the network passphrase into the Passphrase and Confirm boxes.
3.2.2.2.2 802.1X/WPA/WPA2 EAP/TLS SUPPORT
If the 802.1x EAP/TLS option is selected, the encryption method AES or TKIP can
be selected, and a certificate is required for the authentication.
1.
1. To connect to an AP through the RADIUS server, select 802.1x
WPA/WPA2 as the Authentication Mode.
2.
2. Select TKIP or AES as the Encryption Method.
3.
3. Select EAP/TLS (Use Certificate) as the 802.1x Authentication Protocol.
22
Appendix B Error Messages of Enabler Program
Figure 15:: Security Tab—802.1x/WPA/WPA2 EAP/TLS Authentication
4. Click the Configure WPA RADIUS button to configure security settings.
Figure 16:: 802.1x/WPA/WPA2 EAP/TLS RADIUS Configuration Window
23
WM821-M MiniPCI Module
Wireless Utility
—Using the
1.
5. Click Browse to activate the dialog for selecting a certificate.
2.
6. Before clicking OK to exit the dialog, make sure that the Login Name is
entered.
Figure 17:: Select Certificate
24
Appendix B Error Messages of Enabler Program
Figure 18: WPA RADIUS Configuration Window with Certificate
Table 5:: 802.1x/WPA/WPA2 EAP/TLS RADIUS Configuration Window Description
Field/Button
Description
Login Name
Login name to the RADIUS server
Certificate
Certificate selected for authentication
View
Shows the selected certificate
Browse
Selects the certificate
3.2.2.2.3 802.1X/WPA/WPA2 PEAP SUPPORT IN INFRASTRUCTURE
MODE
To connect to an AP through the RADIUS server, select 802.1x/WPA/WPA2 as the
Authentication Mode, PEAP as the Authentication Protocol, and AES or TKIP as the
Encryption Method.
25
WM821-M MiniPCI Module
Wireless Utility
—Using the
Figure 19::Security tab 802.1x/WPA/WPA2 PEAP RADIUS Authentication
Figure 25: 802.1x/WPA/WPA2 PEAP RADIUS
Configuration Window
26
Appendix B Error Messages of Enabler Program
Figure 20: 802.1x/WPA/WPA2 PEAP RADIUS Configuration Window
Table 6: WPA PEAP RADIUS Configuration Window Description
Field
Description
Login Name
Login name to the RADIUS server
Password
Password to login to the RADIUS server
Domain
Domain name for login to the RADIUS server (optional)
Inner EAP Protocol
Use EAP/MS-CHAP V2 or EAP/GTC to login to the
RADIUS server
Click OK to set the configuration.
3.2.2.2.4 WPA/WPA2 EAP/TTLS
27
WM821-M MiniPCI Module
Wireless Utility
—Using the
To connect to an AP through the RADIUS server, select WPA/WPA2 as the Authentication Mode, TTLS as the 802.1x Authentication Protocol, and TKIP as the
Encryption Method for WPA TTLS or AES as the Encryption Method for WPA2
TTLS.
Figure 21: WPA/WPA2 EAP/TTLS Authentication
Clicking the Configure WPA RADIUS button displays the WPA EAP/TTLS
RADIUS Configuration window. Enter all the required information.
28
Appendix B Error Messages of Enabler Program
Figure 22:WPA EAP RADIUS Configuration window
Table 7: WPA TTLS RADIUS Configuration Window Description
Field
Description
Inner Authentication Protocol
Currently supports EAP/MS-CHAP V2 only
Anonymous Name
Indicates the identity of the authentication server
with which to make contact
Login Name
Login name to the RADIUS server
Password
Password to login to the RADIUS server
Domain
Domain name for login to the RADIUS server (optional)
Click OK to set the configuration.
29
WM821-M MiniPCI Module
Wireless Utility
—Using the
3.2.2.2.5 CCX EAP/LEAP
To connect to a Cisco AP through the RADIUS server, select CCX EAP/LEAP.
WEP is the Encryption Method, and the key is generated automatically.
Figure 23:: Security TabTab-CCX EAP/LEAP Authentication
If Allow Fast Roaming (CCKM) is selected, Fast Roaming (Cisco Centralized
Key Management (CCKM)) is enabled.
Clicking the CCX Configuration button displays the CCX LEAP RADIUS Configuration window. Enter all the required information.
30
Appendix B Error Messages of Enabler Program
Figure 24:: CCX EAP/LEAP
EAP/LEAP RADIUS Configuration Window
Table 8:: CCX EAP/LEAP RADIUS Configuration Window Description
Field
Description
Login Name
Login name to the RADIUS server
Password
Password to login to the RADIUS server
Domain
Domain name for login to the RADIUS server (optional)
Click OK to set the configuration.
3.2.2.3 Encryption Methods
The following encryption methods are available, depending on the authentication
mode:
• Security Off
• WEP
• TKIP
• AES
3.2.2.4 WEP Key Settings
31
WM821-M MiniPCI Module
Wireless Utility
—Using the
If the WEP Encryption Method is selected, the Security tab displays the WEP Key
Setting. To configure the WEP keys, select the WEP Key Setting, and click the
Configure WEP Keys button.
Note
The WEP key used for the transmission must be identical on the sending
and the receiving station.
Figure 25: Security Tab-WEP Key Settings
Clicking the Configure WEP Keys button displays the Configure WEP Key window.
Enter all the required information.
32
Appendix B Error Messages of Enabler Program
Figure 26: WEP Key Configuration Window
Table 9: WEP Key Configuration Window Description
Field
Description
Key Format
Either ASCII characters or hexadecimal digits
Key Size
• 40-bit, 5 character ASCII key size (40-bit, 10 character
hexadecimal) • 104-bit, 13 character ASCII key size
(104-bit, 26 character hexadecimal)
There are four transmit keys. The key value is in ASCII or
hexadecimal,
depending on the format selected. The WEP key size
shown depends on the key
size selected.
Transmit Keys
33
WM821-M MiniPCI Module
Wireless Utility
—Using the
Click OK to set the configuration.
3.2.2.5 TKIP/AES Settings
If TKIP/AES is selected and the Authentication Mode is WPA-PSK or WPA2-PSK,
the security tab displays the TKIP/AES passphrase settings. Enter the passphrase
into the Passphrase and Confirm boxes, and click OK.
Figure 27: TKIP/AES Settings
Currently, only the functions WPA-PSK + TKIP and WPA2-PSK + AES are available. There is no such combination as WPA-PSK + AES or WPA2-PSK + TKIP.
3.2.3 Profile Setting—Protocol Tab
34
Appendix B Error Messages of Enabler Program
The Protocol tab allows you to set or change the protocol information.
Figure 28:: Protocol Tab
DO NOT CHANGE SETTINGS
If this check box is selected, the protocol setting is not changed when the profile is
applied.
USE BELOW SETTINGS If the Do not change setting check box is not selected, the protocol settings include the following parameters.
Table 10:: Protocol Tab Description
Field
Description
35
WM821-M MiniPCI Module
Wireless Utility
Power Save Mode
Preamble (802.11b)
Transmit Rate
Fragment Threshold
Region Code
RTS/CTS Threshold
Reset
Sets the power mode. Available options are Continuous
Access or Max Power Save. The default setting is Continuous Access.
Sets the Radio Preamble to Auto, Short or Long. This
option takes effect only when attaching to an 802.11b
network.
The range of the data rate depends on the type of AP
that the client card is connected to. The default setting is
Auto Select. MCS index will be allowed to select when
the 802.11n Network check box in the Network Info tab
is selected.
Sets the fragmentation threshold (the size that packets
are fragmented into for transmission). The default setting
is 2346.
Sets the region code. Available options are FCC (U.S.),
IC (Canada), ETSI (Europe), Spain, France, and MKK
(Japan).
Sets the packet size at which the AP issues a RequestTo-Send (RTS) or Clear-to-Send (CTS) frame before
sending the packet. The default setting is 2347.
Resets the protocol settings to their default values
3.3 Site Survey Tab
36
—Using the
Appendix B Error Messages of Enabler Program
Figure 29:: Site Survey Tab
3.3.1 Site Survey—Networks Filter
This section lets you customize which sites are displayed in the Site Survey list:
•
Display 802.11a Access Points—selecting this check box displays all
802.11a APs within range.
•
Display 802.11g Access Points—selecting this check box displays all
802.11g APs within range.
•
Display 802.11b Access Points—selecting this check box displays all
802.11b APs within range.
3.3.2 Site Survey—List of Detected Stations
This section reports information on the AP stations detected.
37
WM821-M MiniPCI Module
Wireless Utility
—Using the
Figure 30: Site Survey-List of Detected Stations
Table 11: List of Detected Stations Description
Field
Description
Network SSID
Network SSID label (i.e., the Network Name). The Network Name is a text string.
MAC address, a hardware address that uniquely identifies each node of a
network
MAC Address
Security
Security enabled or disabled
CH
Channel used by the detected device
Signal
Signal strength of the detected device as a percentage
Icons
The following icons may be displayed left of the Network SSID: • An antenna icon with a subscript a
indicates an 802.11a AP.
• An antenna icon with a subscript b indicates an
802.11b AP.
• An antenna icon with a subscript g indicates an
802.11g AP. • A circle around the antenna icon means
the client card is connected to this
network.
Wireless Multimedia Enhancements (WMM) supported
by the detected device
WMM
38
Appendix B Error Messages of Enabler Program
EWC
Draft-802.11n/EWC functionality supported by the detected device
Network Type
Type of environment connected to Infrastructure
3.3.3 Site Survey—Filter Button
Clicking the Filter button displays the Advanced Filter window.
Figure 31: Figure 36: Site Survey—Advanced Filter Window
3.3.3.1 Network SSID
•
Any SSID—no specific SSID is used when scanning for available networks in the area.
39
WM821-M MiniPCI Module
Wireless Utility
•
SSID.
—Using the
Find network with this SSID—the utility searches for the specified
3.3.3.2 Network BSSID
•
Any BSSID—no specific BSSID is used when scanning for available
networks in the area.
•
Find network with this BSSID—the utility searches for the specified
BSSID.
3.3.3.3 Select Channel
•
Scan all channels—all channels are scanned when searching for
available networks in the area.
•
Scan channel Only—only the specified channel is scanned when
searching for available networks in the area.
•
Scan Channel to Channel—a range of channels are scanned when
searching for available networks in the area.
3.3.4 Site Survey—Refresh Button
Clicking the Refresh button requests a survey of the wireless
networks in the area.
3.3.5 Site Survey—Associate Button
Select an available network, and then click the Associate button to establish a connection. Alternatively, the connection can be established by double-clicking the
selected network.
3.4 Statistics Tab
Clicking the Statistics tab displays the statistics
of the current connect session.
40
Appendix B Error Messages of Enabler Program
Figure 32: Statistics Tab
3.4.1 Signal Strength
The color-coded Signal Strength bar displays the signal strength of the last packet
received by the client card. Signal strength is reported as a percentage. A signal in
the red indicates a bad connection. A signal in the green indicates a good connection.
3.4.2 Transmit Section
41
WM821-M MiniPCI Module
Wireless Utility
—Using the
The Transmit section displays the information on the packets sent.
Figure 33: Transmit Section
Table 12: Transmit Section Description
Field
Description
Total Packet
Reports the total number of packets transmitted
Unicast Packet
Multicast Packet
Single Retries
42
Reports the number of packets transmitted by the client
card that were destined
for a single network node
Reports the number of packets transmitted by the client
card that were destined
for more than one network node
Reports the number of packets that require one retry before the client card received an acknowledgement.
Appendix B Error Messages of Enabler Program
Multiple Retries
Failed Count
RTS Success
RTS Failure
ACK Error
NOTE:After the client card sends a packet, it waits for an
acknowledge from the receiving radio to confirm that the
packet was successfully received. If the acknowledge is
not received within a specified period of time, the client
card retransmits the packet.
Reports the number of packets that require more than
one retry before the client
card received an acknowledgement
Reports the number of packets that were not successfully
transmitted because
the client card did not receive an acknowledge within the
specified period of time
Reports the number of RTS attempts that were successful
Reports the number of RTS attempts that were not successful
Reports the number of unicast transmit attempts for
which no acknowledgement
was received
3.4.3 Receive Section
The Receive section displays the information on the packets received.
Figure 34: Receive Section
43
WM821-M MiniPCI Module
Wireless Utility
—Using the
Table 13: Receive Section Description
Field
Description
Total Packet
Reports the total number of packets received
Unicast Packet
Multicast Packet
Duplicate Frame
Received Beacons
Beacon Loss
Reports the number of packets received by the client
card that were destined for
a single network node
Reports the number of packets received by the client
card that were destined for
more than one network node
Reports the number of duplicate frames received
Reports the number of beacons received after association is established
Reports the number of missing beacons after association
is established
3.4.4 Protocol Section
The Protocol section displays the information on the protocol status. Figure 40:
Protocol Section
44
Appendix B Error Messages of Enabler Program
Figure 35: Protocol Section
Table 14: Protocol Section Description
Field
Description
Preamble
Displays radio preamble type: • Auto
• Short
• Long
Tx Power
Displays transmit power mode: • Auto
• High
• Medium
• Low
3.5 Advanced Tab
The Advanced tab displays the advanced parameters available for the installed
WM821-M client cards.
45
WM821-M MiniPCI Module
Wireless Utility
—Using the
Figure 36: Advanced Tab
Note The Advanced tab is not accessible when the Windows Zero Configuration Utility is enabled.
3.5.1 Advanced Tab—WM821-M Wireless Card
46
Appendix B Error Messages of Enabler Program
This section of the Advanced tab reports the type of WM821-M client card installed.
3.5.2 AdvancedTab—Miscellaneous
Figure 37: Miscellaneous Section
Table 15: Advanced Tab Miscellaneous Section Description
Field
Description
Auto connect if link loss or no connection
(Use checked profiles in )
Clear this check box to disable the autoconfiguration feature. Whenever there is
a link loss, auto-configuration tries to
establish a connection to the checked
profiles in the Profile Manager window.
Select this check box for performance
enhancement.
Select this check box to enable/disable
the Wireless Multimedia Enhancements
(WMM) feature.
Select this check box to set the regulatory domain
Boost Mode
Enable WMM
Worldwide regulatory domain
47
WM821-M MiniPCI Module
Wireless Utility
—Using the
DFS Mode
Select this check box to enable Dynamic
Frequency Selection (DFS)
MIMO Powersave
Enables/disables the Multiple Input Multiple Output (MIMO) Powersave Mode.
Available options are Off and Static.
3.6 AutoLink Tab
To enable AutoLink mode, proceed as follows:
1.
2.
1. Toggle the AutoLink button on the Access Point to enable AutoLink mode.
2. Toggle the AutoLink button on the client to enter AutoLink mode.
Figure 38: Access Point Autolink Button
Within 60 seconds, the AutoLink will be completed.
48
Appendix B Error Messages of Enabler Program
Figure 39: Auto Link Tab (Client)
AutoLink is complete.
49
WM821-M MiniPCI Module
Wireless Utility
—Using the
3.7 Admin Tab
The Admin tab allows you to import and export profiles.
Figure 40: Admin Tab
3.7.1 Admin Tab—Import Profiles
50
Appendix B Error Messages of Enabler Program
To import a profile, proceed as follows:
1.
2.
3.
1. Click Import Profiles.
2. Select the path and filename of the profile.
3. Click Open.
3.7.2 Admin Tab—Export Profiles
To export a profile, proceed as follows:
1.
2.
3.
1. Click Export Profiles.
2. Select or enter the path and filename of the profile.
3. Click Save.
3.8 About Tab
The About tab displays information about the WM821-M Client
Card Configuration Utility.
51
WM821-M MiniPCI Module
Wireless Utility
—Using the
Figure 41: About Tab
52
Appendix A
Specifications
Specifications
Product Name
Draft 802.11n-compatible Dual Band WLAN mPCI
Card
Interface
mPCI 32 Type III-B
Network Standards
IEEE802.11a/g/b Draft n-compliant
54, 48, 36, 24, 18, 12, 9, 6, 11, 5.5, 2,1Mbps
Data Rate
20MHz BW: 130, 117, 104, 78, 52, 39, 26 and
13Mbps
40MHz BW: 300, 270, 243, 216, 162, 108, 81, 54
and 27Mbps
Modulation
802.11a/g/n---- 54, 48, 36,24,18,12,9,6Mbps
(OFDM)
802.11b ---- CCK (11Mbps, 5.5Mbps), QPSK
(2Mbps), BPSK (1Mbps)
2.412 ~ 2.462 GHz: North America
2.412 ~ 2.472 GHz: Europe ETSI
2.412 ~ 2.472 GHz: Japan (ARIB STD-T66)
Operating Frequency
5.15 ~ 5.35GHz/ 5.47 ~ 5.825 GHz: North America UNII
5.15 ~ 5.35GHz/ 5.47 ~ 5.725GHz: Europe ETSI
4.9 ~ 5.0GHz/ 5.15 ~ 5.35GHz: Japan (TBD)
Operating Channels
11g: 1~11 for America,1~13 for Europe (ETSI)
and Japan (ARIB STD-66)
11b: 1~11 for America,1~13 for Europe
(ETSI),1~14 for Japan
53
WM821-M MiniPCI Module
Wireless Utility
—Using the
11a: 36-64, 100-161 North America; 36-64 for
Japan and other ch definitions
RF Output Power
(TBD) 12 dBm (5GHz), 15dBm (2.4GHz)
(54Mbps, OFDM, typical)
(TBD)18 dBm (2.4GHz, 11Mbps, CCK, typical)
Antenna
LED Indicators
Three IPEX connectors with diversity for external
antenna
Power LED: GPIO control
Link LED: GPIO control
Indoor: 20M@54Mbps, 35M@24Mbps,
60M@6Mbps, 100M@11Mbps
Coverage Area
Receiver Sensitivity
Outdoor: 50M@54Mbps, 65M@48Mbps,
90M@36Mbps, 120M@24,18,12,9,6Mbps,
80M@11Mbps, 120M@5.5Mbps, 200M@2Mbps,
300M@1Mbps
-70 dBm @ 54M (OFDM, 10% PER)
-86 dBm @ 11M (CCK, 8% PER)
Power Consumption
TX power consumption: <680mA @3.3V
RX power consumption: <670mA @3.3V
Support OS
Linux, Microsoft Windows Windows 2K, Windows
XP (TBD)
Operating Temperature
0 to 55 ℃
Humidity
20% to 95% Non-condensing
Dimensions (mm)
(W) 59.6mm × (D) 44.45mm × (H) 4.9mm
Weight (g)
28 g
Voltage
3.3V
54

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print
XMP Toolkit                     : 3.1-701
About                           : f104d994-2ae8-11dc-0000-9b5ce71df1dd
Producer                        : AFPL Ghostscript 8.54
Modify Date                     : 2007:07:03 09:58:47+08:00
Create Date                     : 2007:07:02 19:12:14+08:00
Creator Tool                    : PDFCreator Version 0.9.2
Metadata Date                   : 2007:07:03 09:58:47+08:00
Document ID                     : f104d994-2ae8-11dc-0000-9b5ce71df1dd
Instance ID                     : uuid:88ce83bd-a825-48b5-a419-9ded385bb366
Format                          : application/pdf
Title                           : User manual - rev 0702
Creator                         : Joy
Page Count                      : 62
Author                          : Joy

EXIF Metadata provided by EXIF.tools