Cypress Semiconductor 3039 This product is a Bluetooth wireless EZ-BT WICED XR Module with Mesh User Manual CYBT 013033 01 EZ BT Module

Download:
Mirror Download [FCC.gov]
Document ID	3880529
Application ID	cg/+23OgB7MsZhVfrHbZ+A==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	123.87kB (1548321 bits)
Date Submitted	2018-06-08 00:00:00
Date Available	2018-06-08 00:00:00
Creation Date	2017-01-26 11:24:31
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2018-06-07 14:40:32
Document Title	CYBT-013033-01 EZ-BTâ„¢ Module
Document Creator	FrameMaker 7.0
Document Author:	DSO

PRELIMINARY
CYBT-483039-02
®
EZ-BT™ XR WICED
Module
General Description
The CYBT-483039-02 is a dual-mode Bluetooth BR/EDR and
Low Energy (BLE) wireless module solution. The
CYBT-483039-02 includes onboard crystal oscillators, passive
components, PA/LNA, and the Cypress CYW20719 silicon
device.
RX current consumption
p Bluetooth silicon: 5.9 mA (MCU + radio only)
p RFX2401C: 8.0 mA (PA/LNA only)
Cypress CYW20719 silicon low power mode support
p PDS: 61 μA with 512 KB SRAM retention
p SDS: 1.6 uA
p HIDOFF (External Interrupt): 400 nA
The CYBT-483039-02 supports a number of peripheral functions
(ADC, PWM), as well as multiple serial communication protocols
(UART, SPI, I2C, I2S/PCM). The CYBT-483039-02 includes a
royalty-free stack compatible with Bluetooth 5.0 in a 12.75 ×
18.59 × 1.80 mm module form-factor.
The CYBT-483039-02 includes an integrated chip antenna,
on-board external power/low noise amplifier, qulaified by
Bluetooth SIG, and includes regulatory certification approval for
FCC, ISED, MIC, and CE.
Module Description
Module size: 12.75 mm × 18.59 mm × 1.80 mm
Complies with Bluetooth Core Specification version 5.0
supporting BR, EDR 2/3 Mbps, eSCO, BLE, and LE 2 Mbps .
p QDID: TBD
p Declaration ID: TBD
True Extended Range:
Up to 1 kilometer bidirectional communication[1, 2]
Functional Capabilities
1x ADC with (12-bit ENoB for DC measurement and 13-bit
ENoB for Audio measurement) with 10 channels.
1x HCI UART for programming and HCI
1x peripheral UART (PUART)
2x SPI (master or slave) blocks (SPI, Quad SPI, MIPI DBI-C)
1x I2C master/slave and 1x I2C master only
I2S/PCM audio interfaces
Up to 6 16-bit PWMs
Watchdog Timer
Bluetooth Basic Rate (BR) and Enhanced Data Rate (EDR)
Support
BLE protocol stack supporting generic access profile (GAP)
Central, Peripheral, or Broadcaster roles
Hardware Security Engine
Certified to FCC, ISED, MIC, and CE standards
Up to 15 GPIOs
1024-KB flash memory, 512-KB SRAM memory
Benefits
Industrial temperature range: –30 °C to +85 °C
Integrated ARM Cortex-M4 microprocessor core with
floating point unit (FPU)
CYBT-483039-02 is fully integrated and certified solution that
provides all necessary components required to operate
Bluetooth communication standards.
RF Characteristics
Proven hardware design ready to use
Ultra-flexible supermux I/O designs allows maximum flexibility
for GPIO function assignment
Maximum TX output power(EIRP): +20.0 dBm
Conducted output power:
p +17.6dBm for BT3.0, +16.8dBm for BT4.0
Large non-volatile memory for complex application development
Antenna peak gain: 2.3 dBi
Over-the-air update capable for development or field updates
BLE RX Receive Sensitivity: –95.0 dbm
Bluetooth SIG qualified with QDID and Declaration ID
Received signal strength indicator (RSSI) with 1-dB resolution
WICED™ Studio provides an easy-to-use integrated design
environment (IDE) to configure, develop, program, and test
your Bluetooth application
Power Consumption
TX current consumption
BLE silicon: 5.6 mA (MCU + radio only, 0 dbm)
p RFX2401C: 100 mA peak (PA/LNA only, +17.5 dBm Pout)
p RFX2401C: 27 mA peak (PA/LNA only, +7.5 dBm Pout)
Notes
1. Connection range tested module-to-module in full line-of-sight environment, free of obstacles or interference sources with output power of +18 dBm POUT.
2. Specified as EZ-BT XT module to module range. Mobile phone connection will decrease based on the PA/LNA performance of the mobile phone used.
Cypress Semiconductor Corporation
Document Number: 002-23993 Rev. **
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised May 22, 2018
PRELIMINARY
CYBT-483039-02
More Information
Cypress provides a wealth of data at www.cypress.com to help you to select the right module for your design, and to help you to
quickly and effectively integrate the module into your design.
References
Overview: EZ-BLE/EZ-BT Module Portfolio, Module Roadmap
Development Kits:
p CYBT-483039-EVAL, CYBT-483039-02 Evaluation Board
p CYW920719Q40EVB-01, Evaluation Kit for CYW20719
silicon device
Test and Debug Tools:
®
p CYSmart, Bluetooth LE Test and Debug Tool (Windows)
®
p CYSmart Mobile, Bluetooth LE Test and Debug Tool
(Android/iOS Mobile App)
Knowledge Base Article
p KBA97095 - EZ-BLE™ Module Placement
p KBA213976 - FAQ for BLE and Regulatory Certifications with
EZ-BLE modules
p KBA210802 - Queries on BLE Qualification and Declaration
Processes
p KBA218122 - 3D Model Files for EZ-BLE/EZ-BT Modules
p KBA223428- Programming an EZ-BT WICED Module
Development Environments
Wireless Connectivity for Embedded Devices (WICED) Studio Software Development Kit (SDK)
Cypress' WICED® (Wireless Connectivity for Embedded Devices) is a full-featured platform with proven Software Development Kits
(SDKs) and turnkey hardware solutions from partners to readily enable Wi-Fi and Bluetooth® connectivity in system design.
WICED Studio is the only SDK for the Internet of Things (ioT) that combines Wi-Fi and Bluetooth into a single integrated development
environment. In addition to providing WICED APIs and an application framework designed to abstract complexity, WICED Studio also
leverages many common industry standards.
Technical Support
Cypress Community: Whether you’re a customer, partner or a developer interested in the latest Cypress innovations, the Cypress
Developer Community offers you a place to learn, share and engage with both Cypress experts and other embedded engineers
around the world.
Frequently Asked Questions (FAQs): Learn more about our Bluetooth ECO System.
Visit our support page and create a technical support case or contact a local sales representatives. If you are in the United States,
you can talk to our technical support team by calling our toll-free number: +1-800-541-4736. Select option 2 at the prompt.
Document Number: 002-23993 Rev. **
Page 2 of 49
PRELIMINARY
Contents
Overview............................................................................ 4
Functional Block Diagram ........................................... 4
Module Description...................................................... 4
Pad Connection Interface ................................................ 6
Recommended Host PCB Layout ................................... 8
Module Connections ...................................................... 10
Connections and Optional External Components ..... 12
Power Connections (VDD and VDDPA).................... 12
External Reset (XRES).............................................. 13
HCI UART Connections ............................................ 13
External Component Recommendation .................... 13
Critical Components List ........................................... 15
Antenna Design......................................................... 15
Power Amplifier (PA) and Low Noise Amplifier (LNA) 15
Bluetooth Baseband Core ............................................. 16
BQB and Regulatory Testing Support ....................... 16
Power Management Unit................................................ 17
Integrated Radio Transceiver ........................................ 18
Transmitter Path........................................................ 18
Receiver Path............................................................ 18
Local Oscillator.......................................................... 18
Microcontroller Unit ....................................................... 19
External Reset........................................................... 19
Peripheral and Communication Interfaces .................. 20
I2C............................................................................. 20
HCI UART Interface .................................................. 20
Peripheral UART Interface ........................................ 20
Serial Peripheral Interface......................................... 20
32 kHz Crystal Oscillator ........................................... 20
ADC Port ................................................................... 22
GPIO Ports ................................................................ 22
PWM.......................................................................... 23
PDM Microphone....................................................... 24
I2S Interface .............................................................. 24
PCM Interface ........................................................... 24
Security Engine ......................................................... 25
Power Modes .................................................................. 26
Document Number: 002-23993 Rev. **
CYBT-483039-02
Firmware..........................................................................
Electrical Characteristics...............................................
Core Buck Regulator .................................................
Digital LDO ................................................................
Digital I/O Characteristics..........................................
ADC Electrical Characteristics ..................................
Bluetooth Silicon Current Consumption ....................
Chipset RF Specifications .............................................
Timing and AC Characteristics .....................................
UART Timing.............................................................
SPI Timing.................................................................
I2C Compatible Interface Timing...............................
I2S Interface Timing ..................................................
Environmental Specifications .......................................
Environmental Compliance .......................................
RF Certification..........................................................
Safety Certification ....................................................
Environmental Conditions .........................................
ESD and EMI Protection ...........................................
Regulatory Information ..................................................
FCC ...........................................................................
ISED ..........................................................................
European Declaration of Conformity .........................
MIC Japan .................................................................
Packaging........................................................................
Ordering Information......................................................
Acronyms ........................................................................
Document Conventions .................................................
Units of Measure .......................................................
Document History Page .................................................
Sales, Solutions, and Legal Information ......................
Worldwide Sales and Design Support.......................
Products ....................................................................
PSoC® Solutions ......................................................
Cypress Developer Community.................................
Technical Support .....................................................
26
27
27
29
29
29
30
31
34
34
35
37
38
40
40
40
40
40
40
41
41
42
43
43
44
46
47
47
47
48
49
49
49
49
49
49
Page 3 of 49
PRELIMINARY
CYBT-483039-02
Overview
Functional Block Diagram
Figure 1 illustrates the CYBT-483039-02 functional block diagram.
Figure 1. Functional Block Diagram
Note: General Purpose Input/Output pins shown in Figure 1 are configuratble to any specified input or output function in the SuperMux table detailed in Table 5 in the Module
Connections section.
Note: Connections shown in the above block diagram are maximum number of connections per function. The total number of GPIOs available on the CYBT-483039-02 is 15.
Module Description
The CYBT-483039-02 module is a complete module designed to be soldered to the applications main board.
Module Dimensions and Drawing
Cypress reserves the right to select components from various vendors to achieve the Bluetooth module functionality. Such selections
will still guarantee that all mechanical specifications and module certifications are maintained. Any changes to the current BOM for
the CYBT-483039-02 will not be made until approval is provided by the end customer for this product. The CYBT-483039-02 will be
held within the physical dimensions shown in the mechanical drawings in Figure 2 on page 5. All dimensions are in millimeters (mm).
Table 1. Module Design Dimensions
Dimension Item
Module dimensions
Antenna location dimensions
Specification
Length (X)
12.75 ± 0.15 mm
Width (Y)
18.59 ± 0.15 mm
Length (X)
12.75 mm
Width (Y)
4.82 mm
PCB thickness
Height (H)
0.50 ± 0.10 mm
Shield height
Height (H)
1.20 mm
Maximum component height
Height (H)
1.30 mm typical (Chip Antenna)
Total module thickness (bottom of module to top of shield)
Height (H)
1.80 mm typical
See Figure 2 for the mechanical reference drawing for CYBT-483039-02.
Document Number: 002-23993 Rev. **
Page 4 of 49
PRELIMINARY
CYBT-483039-02
Figure 2. Module Mechanical Drawing
Top View (Seen from Top)
Side View
Bottom View (Seen from Bottom)
Notes
3. No metal should be located beneath or above the antenna area. Only bare PCB material should be located beneath the antenna area. For more information on
recommended host PCB layout, see “Recommended Host PCB Layout” on page 8.
Document Number: 002-23993 Rev. **
Page 5 of 49
PRELIMINARY
CYBT-483039-02
Pad Connection Interface
As shown in the bottom view of Figure 2 on page 5, the CYBT-483039-02 has 34 connections to a host board via solder pads (SP).
Table 2 and Figure 3 detail the solder pad length, width, and pitch dimensions of the CYBT-483039-02 module.
Table 2. Connection Description
Name
Connections
Connection Type
Pad Length Dimension
Pad Width Dimension
Pad Pitch
SP
34
Solder Pad
1.02 mm
0.71 mm
1.02 mm
Figure 3. Solder Pad Dimensions (Seen from Bottom)
Solder Pad Connections
(Seen from Bottom)
To maximize RF performance, the host layout should follow these recommendations:
1. Antenna Area Keepout: The host board directly below the antenna area of the Cypress module (see Figure 2 on page 5) must
contain no ground or signal traces. This keep out area requirement applies to all layers of the host board.
2. Module Placement: The ideal placement of the Cypress Bluetooth module is in a corner of the host board with the chip antenna
located at the far corner. This placement minimizes the additional recommended keep out area stated in item 3 below. Please refer
to AN96841 for module placement best practices.
3. Optional Keepout: To maximize RF performance, the area immediately around the Cypress Bluetooth module chip antenna may
contain an additional keep out area, where there are no grounding or signal traces. The keep out area applies to all layers of the
host board. The recommended dimensions of the host PCB keep out area are shown in Figure 4 (dimensions are in mm).
Document Number: 002-23993 Rev. **
Page 6 of 49
PRELIMINARY
CYBT-483039-02
Figure 4. Optional Additional Host PCB Keep Out Area Around the CYBT-483039-02 Chip Antenna
Document Number: 002-23993 Rev. **
Page 7 of 49
PRELIMINARY
CYBT-483039-02
Recommended Host PCB Layout
Figure 5, Figure 6, Figure 7, and Table 3 provide details that can be used for the recommended host PCB layout pattern for the
CYBT-483039-02. Dimensions are in millimeters unless otherwise noted. Pad length of 1.27 mm (0.635 mm from center of the pad
on either side) shown in Figure 7 is the minimum recommended host pad length. The host PCB layout pattern can be completed using
either Figure 5, Figure 6, or Figure 7. It is not necessary to use all figures to complete the host PCB layout pattern.
Figure 5. CYBT-483039-02 Host Layout (Dimensioned)
Top View (Seen on Host PCB)
Document Number: 002-23993 Rev. **
Figure 6. CYBT-483039-02 Host Layout (Relative to Origin)
Top View (Seen on Host PCB)
Page 8 of 49
PRELIMINARY
CYBT-483039-02
Table 3 provides the center location for each solder pad on the CYBT-483039-02. All dimensions are referenced to the center of the
solder pad. Refer to Figure 7 for the location of each module solder pad.
Table 3. Module Solder Pad Location
Figure 7. Solder Pad Reference Location
Solder Pad
(Center of Pad)
Location (X,Y) from
Orign (mm)
Dimension from
Orign (mils)
(0.38, 5.92)
(14.96, 233.07)
(0.38, 6.93)
(14.96, 272.83)
(0.38, 7.95)
(14.96, 312.99)
(0.38, 8.97)
(14.96, 353.15)
(0.38, 9.98)
(14.96, 392.91)
(0.38, 11.00)
(14.96, 433.07)
(0.38, 12.01)
(14.96, 472.83)
(0.38, 13.03)
(14.96, 512.99)
(0.38, 14.05)
(14.96, 553.15)
10
(0.38, 15.06)
(14.96, 592.91)
11
(0.38, 16.08)
(14.96, 633.07)
12
(0.38, 17.09)
(14.96, 672.83)
13
(1.80, 18.21)
(70.87, 716.93)
14
(2.82, 18.21)
(111.02, 716.93)
15
(3.84, 18.21)
(151.18, 716.93)
16
(4.85, 18.21)
(190.94, 716.93)
17
(5.87, 18.21)
(231.10, 716.93)
18
(6.88, 18.21)
(270.87, 716.93)
19
(7.90, 18.21)
(311.02, 716.93)
20
(8.92, 18.21)
(351.18, 716.93)
21
(9.93, 18.21)
(390.94, 716.93)
22
(10.95, 18.21)
(431.10, 716.93)
23
(12.37, 17.09)
(487.01, 672.83)
24
(12.37, 16.08)
(487.01, 633.07)
25
(12.37, 15.06)
(487.01, 592.91)
26
(12.37, 14.05)
(487.01, 553.15)
27
(12.37, 13.03)
(487.01, 512.99)
28
(12.37, 12.01)
(487.01, 472.83)
29
(12.37, 11.00)
(487.01, 433.07)
30
(12.37, 9.98)
(487.01, 392.91)
31
(12.37, 8.97)
(487.01, 353.15)
32
(12.37, 7.95)
(487.01, 312.99)
33
(12.37, 6.93)
(487.01, 272.83)
34
(12.37, 5.92)
(487.01, 233.07)
Document Number: 002-23993 Rev. **
Top View (Seen on Host PCB)
Page 9 of 49
PRELIMINARY
CYBT-483039-02
Module Connections
Table 4 details the solder pad connection definitions and available functions for each connection pad. The GPIO connections available
on the CYBT-483039-02 can be configured to any of the input or output funcitons listed in Table 5. Table 4 specifies any function that
is required to be used on a specific solder pad, and also identifies GPIOs that can be configured using the SuperMux.
Table 4. CYBT-483039-02 Solder Pad Connection Definitions
Pad
XTALI/O
ADC
GPIO
SuperMux Capable[4]
Pad Name
Silicon Pin Name
VDD
VDDIO
GND
GND
Ground
XRES
RST_N
External Reset (Active Low)
P33
P33
IN6
3 see Table 5
P25
P25
3 see Table 5
P26
P26
3 see Table 5
P38
P38
IN1
3 see Table 5
P34/P35/P36
P34
P35
P36
IN5 (P34)
IN4 (P35)
IN3 (P36)
3 (P34/P35/P36)
3 see Table 5
Silicon Power Supply Input (2.0V ~ 3.6V)
P1
P1
IN28
3 see Table 5
10
P0
P0
IN29
3 see Table 5
11
P29
P29
IN10
3 see Table 5
12
P13/P23/P28
P13
P23
P28
IN22 (P13)
IN12 (P23)
IN11 (P28)
3(P13/P23/P28)
3 see Table 5
13
GND
GND
14
P10/P11
P10
P11
IN25 (P10)
IN24 (P11)
3 (P10/P11)
3 see Table 5
15
P17
P17
IN18
3 see Table 5
16
P7
P7
17
P6
P6
3 see Table 5
18
P4
P4
IN20 (P15)
3(P15)
3(P15), see Table 5
Ground
19
XTALO_32K
XTALO_32K
External Oscillator
Output (32KHz)
20
XTALI_32K/
P15[5]
XTALI_32K
P15
External Oscillator Input
(32KHz)
21
UART_CTS_N
BT_UART_CTS_N
UART (HCI UART) Clear To Send Input Only
22
UART_RTS_N
BT_UART_RTS_N
UART (HCI UART) Request To Send Output Only
23
UART_TXD
BT_UART_TXD
UART (HCI UART) Transmit Data Only
24
UART_RXD
BT_UART_RXD
UART (HCI UART) Receive Data Only
25
HOST_WAKE
BT_HOST_WAKE
A signal from the CYBT-483039-02 module to the host indicating that the Bluetooth device requires
attention.
26
GND
GND
Ground
27
GND
GND
Ground
28
GND
GND
Ground
29
GND
GND
Ground
30
GND
GND
Ground
31
GND
GND
Ground
32
VDDPA
N/A
PA/LNA Power Supply Voltage (2.0 ~ 3.6V)
33
GND
GND
Ground
34
GND
GND
Ground
Note
4. The CYBT-483039-02 can configure GPIO connections to any Input/Output function described in Table 5.
5. P15 should not be driven high externally while the part is held in reset (it can be floating or driven low). Failure to do so may cause some current to flow through P15
until the device comes out of reset.
Document Number: 002-23993 Rev. **
Page 10 of 49
PRELIMINARY
CYBT-483039-02
Table 5 details the available Input and Ouput functions that are configurable to any sodler pad in Table 4 that are marked as SuperMux
capable.
Table 5. GPIO SuperMux Input and Output Functions
Function
SWD
Input or Output
Input
Input/Output
Function Type
Serial Communication and
Debug
GPIOs Required
Function Connection Description
SWDCK, Serial Wire Debugger Clock
SWDIO, Serial Wire Debugger I/O
SPI 1 Clock
SPI 1 Chip Select
SPI 1 MOSI
SPI 1
Input/Output
Serial Communication
(Master or Slave)
4~8
SPI 1 MISO
SPI 1 I/O 2 (Quad SPI)
SPI 1 I/O 3 (Quad SPI)
SPI 1 Interrupt
Output
SPI 1 DCX (DBI-C DCX 8-bit mode)
SPI 2 Clock
SPI 2 Chip Select
SPI 2 MOSI
SPI 2
Input/Output
Serial Communication
(Master or Slave)
4~8
SPI 2 MISO
SPI 2 I/O 2 (Quad SPI)
SPI 2 I/O 3 (Quad SPI)
SPI 2 Interrupt
Output
SPI 2 DCX (DBI-C DCX 8-bit mode)
Input
Serial Communication Input
Output
Serial Communication Output
Input/Output
Serial Communication
(Master or Slave)
PUART
I2 C
Periperal UART RX
Peripheral UART CTS
Peripheral UART TX
Peripheral UART RTS
I2 C 2
Input/Output
Serial Communication
(Master or Slave)
PCM In
Input
Audio Input Communication
I2C Clock
I2C Data
I2C 2 Clock
I2C 2 Data
PCM Input
PCM Clock
PCM Sync
PCM Output
PCM Out
Output
Audio Output Communication
PCM Clock
PCM Sync
I2S DI, Data Input
I2S In
Input
Audio Input Communication
I2S WS, Word Select
I2S Clock
I2S DO, Data Output
I2S Out
Ouput
Audio Output Communication
I2S WS, Word Select
I2S Clock
PDM
Input
Document Number: 002-23993 Rev. **
Microphone
1~2
PDM Input Channel 1
PDM Input Channel 2
Page 11 of 49
PRELIMINARY
Function
Input or Output
Function Type
CYBT-483039-02
GPIOs Required
Function Connection Description
PWM Channel 0
PWM Channel 1
PWM Channel 2
PWM
Output
Pulse Width Modulator
1~6
PWM Channel 3
PWM Channel 4
PWM Channel 5
ACLK
Output
Auxiliary Clock
1~2
HIDOFF
Output
HID-OFF Indicator
Auxiliary Clock 0 (ACLK0)
Auxiliary Clock 1 (ACLK1)
HID-OFF Indicator to host
Connections and Optional External Components
Power Connections (VDD and VDDPA)
The CYBT-483039-02 contains two power supply connections, VDD and VDDPA.
VDD is the power supply connection for the Cypress CYW20719 silicon device. VDD accepts a supply input of 1.76 V to 3.63 V.
Table 14 provides this specification. The maximum power supply ripple for this power connection is 100 mV, as shown in Table 14.
VDDPA is the power supply connection for the on-module power amplifier/low-noise amplifier. VDDPA accepts a supply input of 2.00 V
to 3.60 V. Table 14 provides this specification. The maximum power supply ripple for this power connection is 100 mV, as shown in
Table 14.
Considerations and Optional Components for Brown Out (BO) Conditions
Power supply design must be completed to ensure that the CYBT-483039-02 module does not encounter a Brown Out condition,
which can lead to unexpected funcitonality, or module lock up. A Brown Out condition may be met if power supply provided to the
module during power up or reset is in the range shown below:
VIL
≤ VDD ≤ VIH
Refer to Table 18 for the VIL and VIH specifications.
System design should ensure that the condition above is not encountered when power is removed from the system. In the event that
this cannot be guaranteed (i.e. battery installation, high value power capacitors with slow discharge), it is recommended that an
external voltage detection device be used to prevent the Brown Out voltage range from occuring during power removal. Please refer
to Figure 8 for the recommended circuit design when using an external voltage detection IC.
Figure 8. Reference Circuit Block Diagram for External Voltage Detection IC
In the event that the module does encounter a Brown Out condition, and is operating erratically or not responsive, power cycling the
module will correct this issue and once reset, the module should operate correctly. Brown Out conditions can potentially cause issues
that cannot be corrected, but in general, a power-on-reset operation will correct a Brown Out condition.
Document Number: 002-23993 Rev. **
Page 12 of 49
PRELIMINARY
CYBT-483039-02
External Reset (XRES)
The CYBT-483039-02 has an integrated power-on reset circuit which completely resets all circuits to a known power on state. This
action can also be envoked by an external reset signal, forcing it into a power-on reset state. The XRES signal is an active-low signal,
which is an input to the CYBT-483039-02 module (solder pad 3). The CYBT-483039-02 module does not require an external pull-up
resistor on the XRES input
During power on operation, the XRES connection to the CYBT-483039-02 is required to be held low 50 ms after the VDD power supply
input to the module is stable. This can be accomplished in the following ways:
The host device can connect a GPIO to the XRES of Cypress CYBT-483039-02 module and pull XRES low until VDD is stable.
XRES is recommended to be released 50 ms after VDD is stable.
If the XRES connection of the CYBT-483039-02 module is not used in the application, a 0.33 uF capacitor may be connected to the
XRES solder pad of the CYBT-483039-02 in order to delay the XRES release. The capacitor value for this recommended implementation is approximate, and the exact value may differ depending on the VDD power supply ramp time of the system. The capacitor
value should result in an XRES release timing of at least 50 ms after VDD stability.
The XRES release timing may be controlled by a external voltage detection IC. XRES should be released 50 ms after VDD is stable.
Refer to Figure 11 on page 19 for XRES operating and timing requirements during power on events.
HCI UART Connections
The recommendations in this section apply to the HCI UART (Solder Pads 21, 22, 23, and 24). For full UART functionality, all UART
signals must be connected to the Host device. If full UART functionality is not being used, and only UART RXD and TXD are desired
or capable, then the following connection considerations should be followed for UART RTS and CTS:
UART RTS: Can be left floating, pulled low, or pulled high. RTS is not critical for initial firmware uploading at power on.
UART CTS: Must be pulled low to bypass flow control and to ensure that continuous data transfers are made from the host to the
module.
External Component Recommendation
Power Supply Input Options and Circuitry
Two connection options are available for the VDD and VDDPA power supplies:
1. Single supply: Connect VDD and VDDPAto the same supply.
2. Independent supply: Power VDD and VDDPA separately.
In either connection scenario, it is recommended to place an external ferrite bead between the supply and the module connection.
The ferrite bead should be positioned as close as possible to the module pad connection.
The recommended ferrite bead value is 330 Ω, 100 MHz. (Murata BLM21PG331SN1D).
Document Number: 002-23993 Rev. **
Page 13 of 49
PRELIMINARY
CYBT-483039-02
Figure 9 illustrates the CYBT-483039-02 schematic.
Figure 9. CYBT-483039-02 Schematic Diagram
Document Number: 002-23993 Rev. **
Page 14 of 49
PRELIMINARY
CYBT-483039-02
Critical Components List
Table 6 details the critical components used in the CYBT-483039-02 module.
Table 6. Critical Component List
Component
Reference Designator
Silicon
U2
Description
40-pin QFN Bluetooth Silicon Device - CYW20719
Chip Antenna
A1
Antenna, 2.4 GHz, ALA321C3-C
PA/LNA
U2
PA/LNA, RFX2401C
Crystal
Y1
24.000 MHz, 12PF
Antenna Design
Table 7 details the chip antenna used in the CYBT-483039-02 module.
Table 7. Chip Antenna Specifications
Item
Description
Frequency Range
2400 – 2500 MHz
Peak Gain
2.3 dBi typical
Return Loss
10.0 dB typical
Power Amplifier (PA) and Low Noise Amplifier (LNA)
Table 8 details the PA/LNA that is used on the CYBT-483039-02 module. For more information, see Table 8.
Table 8. Power Amplifier/Low Noise Amplifier Details
Item
Description
PA/LNA Manufacturer
Skyworks Inc.
PA/LNA Part Number
RFX2401C
Power Supply Range
2.0V to 3.6V
Table 9 details the power consumption of the integrated PA/LNA used on the More Part Numbers module. Table 9 only details the
current consumption of the RFX2401C PA/LNA. VDD= 3.3 V, TA = +25°C, measured on the RFX2401C evaluation board, unless
otherwise noted.
Table 9. Power Amplifier/Low Noise Amplifier Current Consumption Specifications
Parameter
Test Condition
Min
Typical
Max
Unit
Tx High Power Current
Pout = +18dBm
100
mA
Tx Quiescent Current
No RF applied
17
mA
Rx Quiescent Current
No RF applied
mA
Document Number: 002-23993 Rev. **
Page 15 of 49
PRELIMINARY
CYBT-483039-02
Bluetooth Baseband Core
The Bluetooth Baseband Core (BBC) implements all time-critical functions required for high-performance Bluetooth operation. The
BBC manages the buffering, segmentation, and routing of data for all connections. It prioritizes and schedules all RX/TX activities
including adv, paging, scanning, and servicing of connections. In addition to these functions, it independently handles the host
controller interface (HCI) including all commands, events, and data flowing over HCI. The core also handles symbol timing, forward
error correction (FEC), header error control (HEC), cyclic redundancy check (CRC), authentication, data encryption/decryption, and
data whitening/dewhitening.
Table 10. Bluetooth Features
Bluetooth 1.0
Basic Rate
Bluetooth 1.2
Bluetooth 2.0
Interlaced Scans
EDR 2 Mbps and 3 Mbp
SCO
Adaptive Frequency Hopping
–
Paging and Inquiry
eSCO
–
Page and Inquiry Scan
–
–
Sniff
–
–
Bluetooth 2.1
Secure Simple Pairing
Bluetooth 3.0
Bluetooth 4.0
Unicast Connectionless Data
Bluetooth Low Energy
Enhanced Inquiry Response
Enhanced Power Control
–
Sniff Subrating
eSCO
–
Bluetooth 4.1
Bluetooth 4.2
Bluetooth 5.0
Low Duty Cycle Advertising
Data Packet Length Extension
LE 2 Mbps
Dual Mode
LE Secure Connection
Slot Availability Mask
LE Link Layer Topology
Link Layer Privacy
High Duty Cycle Advertising
BQB and Regulatory Testing Support
The CYBT-483039-02 fully supports Bluetooth Test mode as described in Part I:1 of the Specification of the Bluetooth System Version
3.0. This includes the transmitter tests, normal and delayed loop back tests, and reduced hopping sequence.
In addition to the standard Bluetooth Test Mode, the CYBT-483039-02 also supports enhanced testing features to simplify RF
debugging and qualification and type-approval testing. These features include:
Fixed frequency carrier wave (unmodulated) transmission
p Simplifies some type-approval measurements (Japan)
p Aids in transmitter performance analysis
Fixed frequency constant receiver mode
p Receiver output directed to I/O pin
p Allows for direct BER measurements using standard RF test equipment
p Facilitates spurious emissions testing for receive mode
Fixed frequency constant transmission
p 8-bit fixed pattern or PRBS-9
p Enables modulated signal measurements with standard RF test equipment
Document Number: 002-23993 Rev. **
Page 16 of 49
PRELIMINARY
CYBT-483039-02
Power Management Unit
Figure 10 shows the CYW20719 power management unit (PMU) block diagram. The CYW20719 includes an integrated buck
regulator, a bypass LDO, a capless LDO for digital circuits and a separate LDO for RF. The bypass LDO automatically takes over from
the buck once Vbat supply falls below 2.1V.
The voltage levels shown in this figure are the default settings; the firmware may change voltage levels based on operating conditions.
Figure 10. Default Usage Mode
Document Number: 002-23993 Rev. **
Page 17 of 49
PRELIMINARY
CYBT-483039-02
Integrated Radio Transceiver
The CYBT-483039-02 has an integrated radio transceiver that has been designed to provide low power operation in the globally
available 2.4 GHz unlicensed ISM band. It is fully compliant with Bluetooth Radio Specification 3.0 and meets or exceeds the requirements to provide the highest communication link quality of service.
Transmitter Path
CYBT-483039-02 features a fully integrated transmitter. The baseband transmit data is GFSK modulated in the 2.4 GHz ISM band.
Digital Modulator
The digital modulator performs the data modulation and filtering required for the GFSK signal. The fully digital modulator minimizes
any frequency drift or anomalies in the modulation characteristics of the transmitted signal.
Power Amplifier
The CYBT-483039-02 has an integrated power amplifier (PA) on the silicon device as well as a high power external power amplifier
(PA) integrated on the module. The total output power that this module is designed to achieve is +18 dBm.
Receiver Path
The receiver path uses a low IF scheme to downconvert the received signal for demodulation in the digital demodulator and bit
synchronizer. The receiver path provides a high degree of linearity, and an extended dynamic range to ensure reliable operation in
the noisy 2.4 GHz ISM band. The front-end topology, which has built-in out-of-band attenuation, enables the CYBT-483039-02 to be
used in most applications without off-chip filtering.
Digital Demodulator and Bit Synchronizer
The digital demodulator and bit synchronizer take the low-IF received signal and perform an optimal frequency tracking and bit
synchronization algorithm.
Receiver Signal Strength Indicator
The radio portion of the CYBT-483039-02 provides a receiver signal strength indicator (RSSI) to the baseband. This enables the
controller to take part in a Bluetooth power-controlled link by providing a metric of its own receiver signal strength to determine whether
the transmitter should increase or decrease its output power.
Local Oscillator
The local oscillator (LO) provides fast frequency hopping (1600 hops/second) across the 79 maximum available channels. The
CYBT-483039-02 uses an internal loop filter.
Document Number: 002-23993 Rev. **
Page 18 of 49
PRELIMINARY
CYBT-483039-02
Microcontroller Unit
The CYBT-483039-02 includes a Cortex M4 processor with 2 MB of ROM, 448 KB of data RAM, 64 KB of patch RAM, and 1 MB of
on-chip flash. The CM4 has a maximum speed of 96 MHz. CYBT-483039-02 supports execution from on-chip flash (OCF).
The CM4 also includes a single precision IEEE 754 compliant floating point unit (FPU).
The CM4 runs all the BT layers as well as application code. The ROM includes LM, HCI, L2CAP, GATT, as well as other stack layers
freeing up the flash for application usage. A standard serial wire debug (SWD) interface provides debugging support.
External Reset
An external active-low reset signal, XRES, can be used to put the CYBT-483039-02 in the reset state. An external voltage detector
reset IC with 50 ms delay is recommended on the XRES connection. The XRES must only be released after the VDDO supply voltage level has been stabilized for 50 ms.
Figure 11. Reset Timing
Document Number: 002-23993 Rev. **
Page 19 of 49
PRELIMINARY
CYBT-483039-02
Peripheral and Communication Interfaces
I 2C
The CYBT-483039-02 provides a 2-pin I2C compatible master interface to communicate with I2C compatible peripherals. The following
transfer clock rates are supported are:
100 kHz
400 kHz
800 kHz (Not a standard I2C-compatible speed)
1 MHz (Compatibility with high-speed I2C-compatible devices is not guaranteed)
SCL and SDA lines can be routed to any of the P0-P39 GPIOs allowing for flexible system configuration. When used as SCL/SDA
the GPIOs go into open drain mode and require an external pull-up for proper operation. I2C block does not support multi master
capability by either master or slave devices.
I2C1 is Master Only; I2C2 is Master/Slave. The Slave support is subject to driver support in WICED Studio.
HCI UART Interface
The CYBT-483039-02 includes a UART interface for factory programming as well as when operating as a BT HCI device in a system
with an external host. The UART physical interface is a standard, 4-wire interface (RX, TX, RTS, and CTS) with adjustable baud rates
from 115200 bps to 1.5 Mbps. Typical rates are 115200, 921600, 1500000 bps although intermediate speeds are also available.
Support for changing the baud rate during normal HCI UART operation is included through a vendor-specific command. The
CYBT-483039-02 UART operates correctly with the host UART as long as the combined baud rate error of the two devices is within
±5%. The UART interface has a 1040-byte receive FIFO and a 1040-byte transmit FIFO to support enhanced data rates. The interface
supports the Bluetooth UART HCI (H4) specification. The default baud rate for H4 is 115.2 kbaud.
The CYBT-483039-02 can wake up the host as needed or allow the host to sleep via the HOST_WAKE signal (solder pad 2). signal
allows the CYBT-483039-02 to optimize system power consumption by allowing a host device to remain in low power modes as long
as possible. The HOST_WAKE signal can be enabled via a vendor specific command.
Peripheral UART Interface
The CYBT-483039-02 has a second UART that may be used to interface to peripherals. This peripheral UART is accessed through
the optional I/O ports, which can be configured individually and separately for each functional pin. The CYBT-483039-02 can map the
peripheral UART to any GPIO. The Peripheral UART functionality is the same as the HCI UART, but with a 256-byte transmit and
receive FIFO.
Serial Peripheral Interface
The CYBT-483039-02 has two independent SPI interfaces. Both interfaces support Single, Dual, and Quad mode SPI operations as
well as MIPI DBI-C Interface.Either of the interface can be a master or a slave. SPI2 can support only 1 slave. SPI1 has a 1024 byte
transmit and receive buffers which is shared with the host UART interface. SPI2 has a dedicated 256 byte transmit and receive buffers.
To support more flexibility for user applications, the CYBT-483039-02 has optional I/O ports that can be configured individually and
separately for each functional pin. SPI IO voltage depends on VDDO.
MIPI interface
There are three options in DBI type-C corresponding to 9-bit, 16-bit, and 8-bit modes. The CYBT-483039-02 plays the role of host,
and only the 9-bit and 8-bit modes (option 1 and option 3 in DBI-C spec) are supported. In the 9-bit mode, the SCL, CS, MOSI, and
MISO pins are used. In the 8-bit mode, an additional pin (DCX) is required. The DCX pin indicates if the current outgoing bit stream
is a command or data byte.
32 kHz Crystal Oscillator
The CYBT-483039-02 utlizes the built-in Local Oscillator (LO) on the CYW20719 silicon device for 32kHz timing. The accuracy of the
LO is +/- 500 ppm. The use of an external XTAL oscillator is optional. CYBT-483039-02 includes external XTAL oscilator connections
for applications requiring higher timing accuracy. Figure 12 shows an external 32 kHz XTAL oscillator with external components and
Table 11 lists the the recommended external oscillator’s characteristics. This oscillator input can be operated with a 32 kHz or 32.768
kHz crystal oscillator or be driven with a clock input at similar frequency. The default component values are: R1 = 10 MΩ and C1 =
C2 = ~6 pF. The values of C1 and C2 are used to fine-tune the oscillator.
Document Number: 002-23993 Rev. **
Page 20 of 49
PRELIMINARY
CYBT-483039-02
Figure 12. 32 kHz Oscillator Block Diagram
Table 11. XTAL Oscillator Characteristics
Parameter
Output frequency
Symbol
Foscout
Frequency tolerance
–
Conditions
Minimum
Typical
Maximum
Unit
–
–
32.768
–
kHz
–
100
–
ppm
–
500
–
ms
Crystal-dependent
Start-up time
Tstartup
XTAL drive level
Pdrv
For crystal selection
–
–
0.5
μW
XTAL series resistance
Rseries
For crystal selection
–
–
70
kΩ
XTAL shunt capacitance
Cshunt
For crystal selection
–
–
2.2
pF
External AC Input Amplitude
VIN (AC)
Ccouple = 100 pF;
Rbias= 10 Mohm
400
–
–
mVpp
Document Number: 002-23993 Rev. **
–
Page 21 of 49
PRELIMINARY
CYBT-483039-02
ADC Port
The ADC is a Σ-Δ ADC core designed for audio (13 bits) and DC (12 bits) measurement. It operates at 12 MHz and has 10 solder
pad connections that can act as input channels. The internal bandgap reference has ±5% accuracy without calibration. Calibration
and digital correction schemes can be applied to reduce ADC absolute error and improve measurement accuracy in DC mode.
The following CYBT-483039-02 module solder pads can be used as ADC inputs:
Pad 4: P33, ADC Input Channel 6
Pad 7: P38, ADC Input Channel 1
Pad 8: P34/P35/P36, ADC Input Channels 5/4/3 respectively; NOTE: only one ADC input on this solder pad can be active at a
given time.
Pad 9: P1, ADC Input Channel 28
Pad 10: P0, ADC Input Channel 29
Pad 11: P29, ADC Input Channel 10
Pad 12: P13/P23/28, ADC Input Channels 22/12/11 respectively; NOTE: only one ADC input on this solder pad can be active at a
given time.
Pad 14: P10/P11, ADC Input Channels 25/24 respectively; NOTE: only one ADC input on this solder pad can be active at a given time.
Pad 15: P17, ADC Input Channel 18
Pad 20: P15, ADC Input Channel 20. P15 should not be driven high externally while the part is held in reset (it can be floating or
driven low). Failure to do so may cause some current to flow through P15 until the device comes out of reset.
GPIO Ports
The CYBT-483039-02 has a maximum of 15 general-purpose I/Os (GPIOs). All GPIOs support the following:
Programmable pull-up/down of approximately 45 KOhms.
Input disable, allowing pins to be left floating or analog signals connected without risk of leakage.
Source/sink 8 mA at 3.3V and 4 mA at 1.8V.
P15 is Bonded to the same pin as XTALI_32K (Pad 20). If an External 32.768KHz crystal is not used, then this pin can be used as
GPIO P15.
P26/P28/P29 can sink/source 16 mA at 3.3V and 8 mA at 1.8V.
Most peripheral functions can be assigned to any GPIO. For details, refer to Table 5. For more details on Supermux configuration and
control, refer to "Supermux Wizard for CYW20719" user guide.
The list below details the GPIOs that are available on the CYBT-483039-02 module:
p P0-P1, P4, P6, P7, P17, P25, P26, P29, P33, and P38
p P10/P11 (Double bonded connection on the CYBT-483039-02 module, only one of two is available)
p P13/P23/P28 (Triple bonded connection on the CYBT-483039-02 module, only one of three is available)
p P15/XTALI_32K (Double bonded pin on the CYBT-483039-02 module, only one of two is available)
p P34/P35/P36 (Triple bonded pin on the CYBT-483039-02 module, only one of three is available)
p P19, P20 and P39 are reserved for system use. Please do not use those 3 GPIOs.
For GPIOs highlighted as double or triple bonded connections, only one of the connections can be used at a given time. When a
certain GPIO is selected, the other GPIOs bonded to the same connection must be configured to input with output disable.
Document Number: 002-23993 Rev. **
Page 22 of 49
PRELIMINARY
CYBT-483039-02
PWM
The CYBT-483039-02 has six internal PWMs, labeled PWM0-5. The PWM module consists of the following:
Each of the six PWM channels contains the following registers:
p 16-bit initial value register (read/write)
p 16-bit toggle register (read/write)
p 16-bit PWM counter value register (read)
PWM configuration register shared among PWM0–5 (read/write). This 18-bit register is used:
p To configure each PWM channel
p To select the clock of each PWM channel
p To change the phase of each PWM channel
The application can access the PWM module through the FW driver.
Figure 13 shows the structure of one PWM channel.
Figure 13. PWM Block Diagram
Document Number: 002-23993 Rev. **
Page 23 of 49
PRELIMINARY
CYBT-483039-02
PDM Microphone
The CYBT-483039-02 accepts a ΣΔ-based one-bit pulse density modulation (PDM) input stream and outputs filtered samples at either
8 kHz or 16 kHz sampling rates. The PDM signal derives from an external kit that can process analog microphone signals and generate
digital signals. The PDM input shares the filter path with the auxADC. Two types of data rates can be supported:
8 kHz
16 kHz
The external digital microphone takes in a 2.4 MHz clock generated by the CYBT-483039-02 and outputs a PDM signal which is
registered by the PDM interface with either the rising or falling edge of the 2.4 MHz clock selectable through a programmable control
bit. The design can accommodate two simultaneous PDM input channels, so stereo voice is possible.
Note: Subject to the driver support in WICED Studio.
I2S Interface
The CYBT-483039-02 supports a single I2S digital audio port with both master and slave modes. The I2S signals are:
I2S Clock: I2S SCK
I2S Word Select: I2S WS
I2S Data Out: I2S DO
nI S
Data In: I2S DI
I S SCK and I2S WS become outputs in master mode and inputs in slave mode, while I2S DO always stays as an output. The channel
word length is 16 bits and the data is justified so that the MSN of the left-channel data is aligned with the MSB of the I2S bus, per I2S
Specifications. The MSB of each data word is transmitted one bit clock cycle after the I2S WS transition, synchronous with the falling
edge of bit clock. Left Channel data is transmitted when I2S WS is low, and right-channel data is transmitted when I2S WS is high.
Data bits sent by the CYBT-483039-02 are synchronized with the falling edge of I2S SCK and should be sampled by the receiver on
the rising edge of the I2S SCK.
Note: The PCM interface shares HW with the I2S interface and only one can be used at a given time.
PCM Interface
The CYBT-483039-02 includes a PCM interface that can connect to linear PCM codec devices in master or slave mode. In master
mode, the CYBT-483039-02 generates the PCM_CLK and PCM_SYNC signals. In slave mode, these signals are provided by another
master on the PCM interface and are inputs to the CYBT-483039-02.The configuration of the PCM interface may be adjusted by the
host through the use of vendor-specific HCI commands.
Note: The PCM interface shares HW with the I2S interface and only one can be used at a given time.
Slot Mapping
The CYBT-483039-02 supports up to three simultaneous full-duplex SCO or eSCO channels through the PCM Interface. These three
channels are time-multiplexed onto the single PCM interface by using a time-slotting scheme where the 8 kHz or 16 kHz audio sample
interval is divided into as many as 16 slots. The number of slots is dependent on the selected interface rate (128 kHz, 512 kHz, or
1024 kHz). The corresponding number of slots for these interface rate is 1, 2, 4, 8, and 16, respectively. Transmit and receive PCM
data from an SCO channel is always mapped to the same slot. The PCM data output driver tristates its output on unused slots to allow
other devices to share the same PCM interface signals. The data output driver tristates its output after the falling edge of the PCM
clock during the last bit of the slot.
Frame Synchronization
The CYBT-483039-02 supports both short- and long-frame synchronization in both master and slave modes. In short frame synchronization mode, the frame synchronization signal is an active-high pulse at the audio frame rate that is a single-bit period in width and
is synchronized to the rising edge of the bit clock. The PCGM slave looks for a high on the falling edge of the bit clock and expects
the first bit of the first slot to start at the next rising edge of the clock. In long-frame synchronization mode, the frame synchronization
signal is again an active-high pulse at the audio frame rate; however, the duration is three bit periods and the pulse starts coincident
with the first bit of the first slot.
Data Formatting
The CYBT-483039-02 may be configured to generate and accept several different data formats. For conventional narrow band speech
mode, the CYBT-483039-02 uses 13 of the 16 bits in each PCM frame. The location and order of these 13 bits can be configured to
support various data formats on the PCM interface. The remaining three bits are ignored on the input and may be filled with 0s, 1s, a
sign bit, or a programmed value on the output. The default format is 13-bit 2’s complement data, left justified, and clocked MSB first.
Document Number: 002-23993 Rev. **
Page 24 of 49
PRELIMINARY
CYBT-483039-02
Burst PCM Mode
In this mode of operation, the PCM bus runs at a significantly higher rate of operation to allow the host to duty cycle its operation and
save current. In this mode of operation, the PCM bus can operate at a rate of up to 24 MHz. This mode of operation is initiated with
an HCI command from the host.
Security Engine
The CYBT-483039-02 includes a hardware security accelerator which greatly decreases the time required to perform typical security
operations. Access to the hardware block is provided via a firmware interface (see firmware documentation for details).Thie security
engine includes:
Public key acceleration (PKA) cryptography
AES-CTR/CBC-MAC/CCM acceleration
SHA2 message hash and HMAC acceleration
RSA encryption and decryption of modulus sizes up to 2048 bits
Elliptic curve Diffie-Hellman in prime field GF(p)
Note: Security Engine is used only by the Bluetooth stack to reduce CPU overhead. It is not available for application use.
Random Number Generator
This hardware block is used for key generation for Bluetooth.
Note: Availability for use by the application is subject to the support in WICED Studio.
Note: The Random Number Generator block must be warmed up prior to use. A delay of 500 ms from cold boot is necessary prior to
using the Random Number Generator.
Document Number: 002-23993 Rev. **
Page 25 of 49
PRELIMINARY
CYBT-483039-02
Power Modes
The CYBT-483039-02 support the following HW power modes are supported:
Active mode - Normal operating mode in which all peripherals are available and the CPU is active.
Idle mode - In this mode, the CPU is in “Wait for Interrupt” (WFI) and the HCLK, which is the high frequency clock derived from the
main crystal oscillator is running at a lower clock speed. Other clocks are active and the state of the entire chip is retained.
Sleep mode - In this mode, CPU is in WFI and the HCLK is not running. The PMU determines if the other clocks can be turned off
and does accordingly. State of the entire chip is retained, the internal LDOs run at a lower voltage (voltage is managed by the PMU),
and SRAM is retained.
PDS mode - This mode is an extension of the PMU Sleep wherein most of the peripherals such as UART and SPI are turned off.
The entire memory is retained, and on wakeup the execution resumes from where it paused.
Shut Down Sleep (SDS) - Everything is turned off except the IO Power Domain, RTC, and LPO. The device can come out of this
mode either due to BT activity or by an external interrupt. Before going into this mode, the application can store some bytes of data
into “Always On RAM” (AON). When the device comes out of this mode, the data from AON is restored. After waking from SDS, the
application will start from the beginning (warmboot) and has to restore its state based on information stored in AON. In the SDS
mode, a single BT task with no data activity, such as an ACL connection, BLE connection, or BLE advertisement can be performed.
HIDOFF (Timed-Wake) mode - The device can enter this mode asynchronously, that is, the application can force the device into
this mode at any time. IO Power Domain, RTC, and LPO are the only active blocks. A timer that runs off the LPO is used to wake
the device up after a predetermined fixed time.
HIDOFF (External Interrupt-Waked) mode - This mode is similar to Timed-Wake, but in HID-off mode even the LPO and RTC are
turned off. So, the only wakeup source is an external interrupt.
Transition between power modes is handled by the on-chip firmware with host/application involvement. Please see Firmware Section
for details.
Firmware
The CYBT-483039-02 ROM firmware runs on a real time operating system and handles the programming and configuration of all
on-chip hardware functions as well as the BT/LE baseband, LM, HCI, GATT, ATT, L2CAP and SDP layers. The ROM also includes
drivers for on-chip peripherals as well as handling on-chip power management functions including transitions between different power
modes.
The CYBT-483039-02 is fully supported by the Cypress WICED Studio platform. WICED releases provide latest ROM patches, drivers,
and sample applications allowing customized applications using the CYBT-483039-02 to be built quickly and efficiently.
Please refer to WICED Technical Brief and CYBT-483039-02 Product Guide for details on the firmware architecture, driver documentation, power modes and how to write applications/profiles using the CYBT-483039-02.
Document Number: 002-23993 Rev. **
Page 26 of 49
PRELIMINARY
CYBT-483039-02
Electrical Characteristics
The absolute maximum ratings in the following table indicate levels where permanent damage to the device can occur, even if these
limits are exceeded for only a brief duration. Functional operation is not guaranteed under these conditions. Operation at absolute
maximum conditions for extended periods can adversely affect long-term reliability of the device.
Table 12. Silicon Absolute Maximum Ratings
Specification
Requirement Parameter
Maximum Junction Temperature
Min.
Nom.
Max.
–
–
125
Unit
°C
VDD IO
–0.5
–
3.795
VDD RF
–0.5
–
1.38
VDDBAT3V
–0.5
–
3.795
DIGLDO_VDDIN1P5
–0.5
–
1.65
RFLDO_VDDIN1P5
–0.5
–
1.65
PALDO_VDDIN_5V
–0.5
–
3.795
MIC_AVDD
–0.5
–
3.795
Table 13. ESD/Latchup
Specification
Requirement Parameter
Unit
Min.
Nom.
Max.
ESD Tolerance HBM (Silicon)
–2000
–
2000
ESD Tolerance CDM (Silicon)
–500
–
500
–
200
–
mA
Latch-up
Table 14. Power Supply Specifications
Parameter
Conditions
Min.
Typical
Max.
Unit
VDD input
Module Chipset Input
2.0
3.0
3.60
VDDPA input
Module PA/LNA Input
2.0
3.0
3.60
VDD Ripple
Module Input Ripple (VDDPA, VDD)
–
–
100
mV
VBAT Input
Internal to Module (not accessible)
1.90
3.0
3.6
PMU turn-on time
VBAT is ready.
–
–
300
μs
The CYBT-483039-02 uses an onboard low voltage detector to shut down the part when supply voltage (VDD) drops below operating
range.
Table 15. Power Supply Shut Down Specifications
Parameter
VSHUT
Min.
Typical
Max.
Unit
1.625
1.7
1.76
Core Buck Regulator
Table 16. Silicon Core Buck Regulator
Parameter
Conditions
Input supply voltage DC, VBAT
DC voltage range inclusive of disturbances
CBUCK output current
LPOM only
Document Number: 002-23993 Rev. **
Min.
Typ.
Max.
Unit
1.90
3.0
3.63
–
–
65
mA
Page 27 of 49
PRELIMINARY
CYBT-483039-02
Table 16. Silicon Core Buck Regulator (continued)
Parameter
Conditions
Min.
Typ.
Max.
Unit
Output voltage range
Programmable, 30mV/step
default = 1.2V (bits=0000)
1.2
1.26
1.5
Output voltage DC accuracy
Includes load and line regulation
–4
–
+4
LPOM efficiency (high load)
–
85
–
LPOM efficiency (low load)
–
80
–
40
–
–
μs
Input supply voltage ramp-up time
0 to 3.3V
Minimum capacitor value refers to residual capacitor value after taking into account part-to-part tolerance, DC-bias, temperature,
and aging.
Maximum capacitor value refers to the total capacitance seen at a node where the capacitor is connected. This also includes any
decoupling capacitors connected at the load side, if any.
Document Number: 002-23993 Rev. **
Page 28 of 49
PRELIMINARY
CYBT-483039-02
Digital LDO
Table 17. Digital LDO
Parameter
Input supply voltage, Vin
Conditions
Min.
Typ.
Max.
Unit
Minimum Vin=Vo+0.12V requirement must be
met under maximum load.
1.2
1.2
1.6
Nominal output voltage,Vo
Internal default setting
–
1.1
–
Dropout voltage
At maximum load
–
–
120
mV
Digital I/O Characteristics
Table 18. Digital I/O Characteristics
Symbol
Minimum
Typical
Maximum
Unit
Input low voltage (VDD = 3V)
Characteristics
VIL
–
–
0.8
Input high voltage (VDD = 3V)
VIH
2.4
–
–
Input low voltage (VDD = 1.8V)
VIL
–
–
0.4
Input high voltage (VDD = 1.8V)
VIH
1.4
–
–
Output low voltage
VOL
–
–
0.45
Output high voltage
VOH
VDDO – 0.45V
–
–
IIL
–
–
1.0
μA
Input high current
IIH
–
–
1.0
μA
Output low current (VDD = 3V, VOL = 0.5V)
IOL
–
–
8.0
mA
Output low current (VDD = 1.8V, VOL = 0.5V)
IOL
–
–
4.0
mA
Output high current (VDD = 3V, VOH = 2.55V)
IOH
–
–
8.0
mA
Output high current (VDD = 1.8V, VOH = 1.35V)
IOH
–
–
4.0
mA
Input capacitance
CIN
–
–
0.4
pF
Input low current
UART_TXD VOL (0.5mA)
UART_TXD VOL
–
–
TBD
mA
UART_TXD VOH (0.5mA)
UART_TXD VOH
TBD
–
–
mA
ADC Electrical Characteristics
Table 19. Electrical Characteristics
Parameter
Symbol
Current consumption
ITOT
Power down current
–
Min.
Typ.
Max.
Unit
–
Conditions/Comments
–
mA
At room temperature
–
–
μA
ADC Core Specification
ADC reference voltage
From BG with ±3% accuracy
–
0.85
–
ADC sampling clock
–
–
–
12
–
MHz
Absolute error
–
Includes gain error, offset and
distortion. Without factory calibration.
–
–
Includes gain error, offset and
distortion. After factory calibration.
–
–
For audio application
12
13
–
Bit
For static measurement
10
–
–
For audio application
–
1.6
–
ENOB
ADC input full scale
VREF
–
FS
For static measurement
Conversion rate
–
Document Number: 002-23993 Rev. **
1.8
–
3.6
For audio application
16
–
For static measurement
50
100
–
kHz
Page 29 of 49
PRELIMINARY
CYBT-483039-02
Table 19. Electrical Characteristics (continued)
Parameter
Signal bandwidth
Input impedance
Startup time
Symbol
–
RIN
–
Conditions/Comments
Min.
Typ.
Max.
Unit
Hz
For audio application
20
–
8K
For static measurement
–
DC
–
For audio application
10
–
–
For static measurement
500
–
–
For audio application
–
10
–
ms
For static measurement
–
20
–
μs
–
–
42
dB
KW
MIC PGA Specifications
MIC PGA gain range
–
MIC PGA gain step
–
–
–
–
dB
MIC PGA gain error
–
Includes part-to-part gain variation
–1
–
dB
PGA input referred noise
–
At 42 dB PGA gain A-weighted
–
–
μV
Passband gain flatness
–
PGA and ADC, 100 Hz–4 kHz
–0.5
–
0.5
dB
MIC bias output voltage
–
At 2.5V supply
–
2.1
–
MIC bias loading current
–
–
–
–
mA
MIC bias noise
–
Refers to PGA input 20 Hz to
8 kHz, A-weighted
–
–
μV
MIC bias PSRR
–
at 1 kHz
40
–
–
dB
ADC SNR
–
A-weighted 0 dB PGA gain
78
–
–
dB
ADC THD + N
–
–3 dBFS input 0 dB PGA gain
74
–
–
dB
Always lower than avddBAT
–
–
3.6
MIC Bias Specifications
GPIO input voltage
GPIO source
impedance1
–
Resistance
–
–
kΩ
Capacitance
–
–
10
pF
1. Conditional requirement for the measurement time of 10 μs. Relaxed with longer measurement time for each GPIO input channel.
Bluetooth Silicon Current Consumption
In Table 20, current consumption measurements are taken at module input VDD = 3.0V.
Table 20. SIlicon Current Consumption BT/LE
Operational Mode
Typical
Unit
48 MHz with Pause
1.1
mA
48 MHz Without Pause
2.2
mA
RX
Continuous RX
5.9
mA
TX
Continuous TX - 0 dBm
5.6
mA
61
μA
32 KHz xtal and 16 KB Retention RAM on
1.6
μA
Unconnectable - 1 sec
14
μA
Connectable Undirected - 1 sec
17
μA
Master - 1 sec
TBD
μA
Slave - 1 sec
TBD
μA
HCI
Conditions
PDS
HID-Off (SDS)
Advertising
LE Connection - SDS
Page Scan - PDS
Interlaced - R1
122
μA
Sniff - PDS
500 ms Sniff, 1 attempt, 0 timeout - Master
132
μA
500 ms Sniff, 1 attempt, 0 timeout - Slave
138
μA
Document Number: 002-23993 Rev. **
Page 30 of 49
PRELIMINARY
CYBT-483039-02
Table 20. SIlicon Current Consumption BT/LE
Operational Mode
Conditions
Typical
Unit
6.9
mA
Bi-Directional Data Exchange Continuous DM5 or DH5 packets - Master or Slave
Table 21. Power Amplifier/Low Noise Amplifier Current Consumption Specifications
Parameter
Test Condition
Min
Typical
Max
Unit
Tx High Power Current
Pout = +18dBm
100
mA
Tx Quiescent Current
No RF applied
17
mA
Rx Quiescent Current
No RF applied
mA
Chipset RF Specifications
Table 22 and Table 23 apply to single-ended industrial temperatures. Unused inputs are left open.
Table 22. Chipset Receiver RF Specifications
Parameter
Mode and Conditions
Min
Typ
Max
Unit
–
2402
–
2480
MHz
–
dBm
–
dBm
Frequency range
GFSK, 0.1% BER, 1 Mbps
–
–92.02
π/4-DQPSK, 0.01% BER, 2 Mbps
–
–94.02
8-DPSK, 0.01% BER, 3 Mbps
–
–88.02
–
dBm
All data rates
–
–
–20
dBm
GFSK, 0.1% BER3
–
–
11.0
dB
C/I 1 MHz adjacent channel
GFSK, 0.1%
BER4
–
–
dB
C/I 2 MHz adjacent channel
GFSK, 0.1% BER3
–
–
–30.0
dB
C/I ≥ 3 MHz adjacent channel
GFSK, 0.1% BER5
–
–
–40.0
dB
C/I image channel
GFSK, 0.1% BER3
–
–
–9.0
dB
BER3
–
–
–20.0
dB
π/4-DQPSK, 0.1% BER3
π/4-DQPSK, 0.1% BER4
π/4-DQPSK, 0.1% BER3
π/4-DQPSK, 0.1% BER5
π/4-DQPSK, 0.1% BER3
π/4-DQPSK, 0.1% BER3
–
–
13.0
dB
–
–
dB
–
–
–30.0
dB
–
–
–40.0
dB
–
–
–9.0
dB
–
–
–20.0
dB
8-DPSK, 0.1% BER3
–
–
21.0
dB
C/I 1 MHz adjacent channel
8-DPSK, 0.1%
BER3
–
–
5.0
dB
C/I 2 MHz adjacent channel
8-DPSK, 0.1% BER3
–
–
–25.0
dB
C/I ≥ 3 MHz adjacent channel
8-DPSK, 0.1% BER5
–
–
–33.0
dB
C/I image channel
8-DPSK, 0.1% BER3
–
–
dB
BER3
–
–
13
dB
–
–10.0
–
dBm
RX
sensitivity1
Maximum input
GFSK Modulation
C/I cochannel
C/I 1 MHz adjacent to image channel GFSK, 0.1%
QPSK Modulation
C/I cochannel
C/I 1 MHz adjacent channel
C/I 2 MHz adjacent channel
C/I ≥ 3 MHz adjacent channel
C/I image channel
C/I 1 MHz adjacent to image channel
8PSK Modulation
C/I cochannel
C/I 1 MHz adjacent to image channel 8-DPSK, 0.1%
Out-of-Band Blocking Performance (CW)4
30 MHz to 2000 MHz
Document Number: 002-23993 Rev. **
BDR GFSK 0.1% BER
Page 31 of 49
PRELIMINARY
CYBT-483039-02
Table 22. Chipset Receiver RF Specifications (continued)
Parameter
Mode and Conditions
Min
Typ
Max
Unit
2000 MHz to 2399 MHz
BDR GFSK 0.1% BER
–
–27.0
–
dBm
2498 MHz to 3000 MHz
BDR GFSK 0.1% BER
–
–27.0
–
dBm
3000 MHz to 12.75 GHz
BDR GFSK 0.1% BER
–
–10.0
–
dBm
BDR GFSK 0.1% BER
–
–
–39.0
dBm
Inter-modulation Performance6
BT, interferer signal level
Spurious Emissions
30 MHz to 1 GHz
–
–
–
–57.0
dBm
1 GHz to 12.75 GHz
–
–
–
–55.0
dBm
1.
2.
3.
4.
5.
Dirty TX is off
Up to 1dB of variation may potentially be seen from typical sensitivity specs due to the chip, board and associated variations
The receiver sensitivity is measured at BER of 0.1% on the device interface.
Desired signal is 10 dB above the reference sensitivity level (defined as –70 dBm).
Desired signal is 3 dB above the reference sensitivity level (defined as –70 dBm).
6. Desired signal is -64 dBm Bluetooth-modulated signal, interferer 1 is –39 dBm sine wave at frequency f1, interferer 2 is –39 dBm Bluetooth modulated signal at
frequency f2, f0 = 2*f1 – f2, and |f2 – f1| = n*1 MHz, where n is 3, 4, or 5. For the typical case, n = 4.
Table 23. Chipset Transmitter RF Specifications
Parameter
Min
Typ
Max
Unit
2402
–
2480
MHz
Class 2: GFSK Tx power
–
4.0
–
dBm
Class 2: EDR Tx Power
–
–
dBm
20 dB bandwidth
–
930
1000
kHz
|M – N| = 2
–
–
–20
dBm
|M – N| ≥ 3
–
–
–40
dBm
–
–
–36.0
dBm
Transmitter Section
Frequency range
Adjacent Channel Power
Out-of-Band Spurious Emission
30 MHz to 1 GHz
1 GHz to 12.75 GHz
–
–
–30.0
dBm
1.8 GHz to 1.9 GHz
–
–
–47.0
dBm
5.15 GHz to 5.3 GHz
–
–
–47.0
dBm
–75
–
+75
kHz
DH1 packet
–25
–
+25
kHz
DH3 packet
–40
–
+40
kHz
DH5 packet
–40
–
+40
kHz
Drift rate
–20
20
kHz/50 µs
LO Performance
Initial carrier frequency tolerance
Frequency Drift
Frequency Deviation
Average deviation in payload
(sequence used is 00001111)
140
–
175
kHz
Maximum deviation in payload
(sequence used is 10101010)
115
–
–
kHz
–
–
MHz
Channel spacing
Modulation Accuracy
Document Number: 002-23993 Rev. **
Page 32 of 49
PRELIMINARY
CYBT-483039-02
Table 23. Chipset Transmitter RF Specifications (continued)
Parameter
Min
Typ
Max
Unit
π/4-DQPSK Frequency Stability
π/4-DQPSK RMS DEVM
π/4-QPSK Peak DEVM
π/4-DQPSK 99% DEVM
–10
–
10
kHz
–
–
20
–
–
35
–
–
30
8-DPSK frequency stability
–10
–
10
kHz
–
–
13
8-DPSK RMS DEVM
8-DPSK Peak DEVM
–
–
25
8-DPSK 99% DEVM
–
–
20
1.0 MHz < |M – N| < 1.5 MHz
–
–
–26
dBc
1.5 MHz < |M – N| < 2.5 MHz
–
–
–20
dBm
|M – N| > 2.5 MHz
–
–
–40
dBm
In-Band Spurious Emissions
Table 24. BLE RF Specifications
Parameter
Conditions
Frequency range
N/A
Minimum
Typical
Maximum
Unit
2402
–
2480
MHz
Rx sensitivity (QFN)
LE GFSK, 0.1% BER, 1 Mbps
–
–95.0
Tx power
BLE Silicon Device CYW20719 Only
–
4.0
Tx power
Module total output power
Mod Char: Delta F1 average N/A
Mod Char: Delta F2 max
Mod Char: Ratio
–
dBm
–
dBm
–
–
18
dBm
225
255
275
kHz
N/A
99.9
–
–
N/A
0.8
0.95
–
1. Dirty Tx is Off
2. Up to 1dB of variation may potentially be seen from typical sensitivity specs due to the chip, board and associated variations
3. At least 99.9% of all delta F2 max frequency values recorded over 10 packets must be greater than 185 kHz.
Table 25. CYBT-483039-02 GPS and GLONASS Band Spurious Emission
Min.
Typ.
Max.
Unit
1570-1580 MHz
Parameter
GPS
Condition
–
–160
–
dBm/Hz
1592-1610 MHz
GLONASS
–
–159
–
dBm/Hz
Document Number: 002-23993 Rev. **
Page 33 of 49
PRELIMINARY
CYBT-483039-02
Timing and AC Characteristics
In this section, use the numbers listed in the Reference column of each table to interpret the following timing diagrams.
UART Timing
Table 26. UART Timing Specifications
Reference
Characteristics
Min.
Typ.
Max.
Unit
Delay time, UART_CTS_N low to UART_TXD valid.
–
–
1.50
Bit periods
Setup time, UART_CTS_N high before midpoint of stop bit.
–
–
0.67
Bit periods
Delay time, midpoint of stop bit to UART_RTS_N high.
–
–
1.33
Bit periods
Figure 14. UART Timing
Document Number: 002-23993 Rev. **
Page 34 of 49
PRELIMINARY
CYBT-483039-02
SPI Timing
The SPI interface can be clocked up to 24 MHz.
Table 27 and Figure 15 show the timing requirements when operating in SPI Mode 0 and 2.
Table 27. SPI Mode 0 and 2
Min.
Max.
Unit
Reference
Time from master assert SPI_CSN to first clock edge
Characteristics
45
–
ns
Hold time for MOSI data lines
12
½ SCK
ns
Time from last sample on MOSI/MISO to slave deassert SPI_INT
100
ns
Time from slave deassert SPI_INT to master deassert SPI_CSN
Idle time between subsequent SPI transactions
–
ns
1 SCK
–
ns
Figure 15. SPI Timing, Mode 0 and 2
Document Number: 002-23993 Rev. **
Page 35 of 49
PRELIMINARY
CYBT-483039-02
Table 28 and Figure 16 show the timing requirements when operating in SPI Mode 1 and 3.
Table 28. SPI Mode 1 and 3
Reference
Min.
Max.
Unit
Time from master assert SPI_CSN to first clock edge
45
–
ns
Hold time for MOSI data lines
12
½ SCK
ns
Time from last sample on MOSI/MISO to slave deassert SPI_INT
100
ns
Characteristics
Time from slave deassert SPI_INT to master deassert SPI_CSN
Idle time between subsequent SPI transactions
–
ns
1 SCK
–
ns
Figure 16. SPI Timing, Mode 1 and 3
Document Number: 002-23993 Rev. **
Page 36 of 49
PRELIMINARY
CYBT-483039-02
I2C Compatible Interface Timing
The specifications in Table 29 references Figure 17.
Table 29. I2C Compatible Interface Timing Specifications (up to 1 MHz)
Reference
Characteristics
Minimum
Maximum
Unit
–
100
kHz
Clock frequency
400
800
1000
START condition setup time
650
–
ns
START condition hold time
280
–
ns
Clock low time
650
–
ns
Clock high time
280
–
ns
Data input hold time1
–
ns
Data input setup time
100
–
ns
STOP condition setup time
280
–
ns
–
400
ns
650
–
ns
Output valid from clock
10
Bus free time2
1. As a transmitter, 125 ns of delay is provided to bridge the undefined region of the falling edge of SCL to avoid unintended generation
of START or STOP conditions.
2. Time that the CBUS must be free before a new transaction can start.
Figure 17. I2C Interface Timing Diagram
Document Number: 002-23993 Rev. **
Page 37 of 49
PRELIMINARY
CYBT-483039-02
I2S Interface Timing
I2S timing is shown below in Table 30, Figure 18, and Figure 19.
Table 30. Timing for I2S Transmitters and Receivers
Transmitter
Lower LImit
Clock Period T
Receiver
Upper Limit
Lower Limit
Upper Limit
Notes
Min
Max
Min
Max
Min
Max
Min
Max
Ttr
–
–
–
Tr
–
–
–
Master Mode: Clock generated by transmitter or receiver
HIGH tHC
0.35Ttr
–
–
–
0.35Ttr
–
–
–
LOWtLC
0.35Ttr
–
–
–
0.35Ttr
–
–
–
Slave Mode: Clock accepted by transmitter or receiver
HIGH tHC
–
0.35Ttr
–
–
–
0.35Ttr
–
–
LOW tLC
–
0.35Ttr
–
–
–
0.35Ttr
–
–
Rise time tRC
–
–
0.15Ttr
–
–
–
–
Transmitter
Delay tdtr
–
–
–
0.8T
–
–
–
–
Hold time thtr
–
–
–
–
–
–
–
Receiver
Setup time tsr
–
–
–
–
0.2Ttr
–
–
–
Hold time thr
–
–
–
–
0.2Ttr
–
–
–
1. The system clock period T must be greater than Ttr and Tr because both the transmitter and receiver have to be able to handle the data transfer
rate.
2. At all data rates in master mode, the transmitter or receiver generates a clock signal with a fixed mark/space ratio. For this reason, tHC and
tLC are specified with respect to T.
3. In slave mode, the transmitter and receiver need a clock signal with minimum HIGH and LOW periods so that they can detect the signal. So
long as the minimum periods are greater than 0.35Tr, any clock that meets the requirements can be used.
4. Because the delay (tdtr) and the maximum transmitter speed (defined by Ttr) are related, a fast transmitter driven by a slow clock edge can
result in tdtr not exceeding tRC which means thtr becomes zero or negative. Therefore, the transmitter has to guarantee that thtr is greater than
or equal to zero, so long as the clock rise-time tRC is not more than tRCmax, where tRCmax is not less than 0.15Ttr.
5. To allow data to be clocked out on a falling edge, the delay is specified with respect to the rising edge of the clock signal and T, always giving
the receiver sufficient setup time.
6. The data setup and hold time must not be less than the specified receiver setup and hold time.
Document Number: 002-23993 Rev. **
Page 38 of 49
PRELIMINARY
CYBT-483039-02
Figure 18. I2S Transmitter Timing
Figure 19. I2S Receiver Timing
Document Number: 002-23993 Rev. **
Page 39 of 49
PRELIMINARY
CYBT-483039-02
Environmental Specifications
Environmental Compliance
This Cypress BLE module is produced in compliance with the Restriction of Hazardous Substances (RoHS) and Halogen-Free (HF)
directives. The Cypress module and components used to produce this module are RoHS and HF compliant.
RF Certification
The CYBT-483039-02 module is certified under the following RF certification standards:
FCC: WAP3039
IC: 7922A-3039
MIC: TBD
CE
Safety Certification
The CYBT-483039-02 module complies with the following safety regulations:
Underwriters Laboratories, Inc. (UL): Filing E331901
CSA
TUV
Environmental Conditions
Table 31 describes the operating and storage conditions for the Cypress BLE module.
Table 31. Environmental Conditions for CYBT-483039-02
Description
Operating temperature
Operating humidity (relative, non-condensation)
Thermal ramp rate
Minimum Specification
Maximum Specification
−30 °C
85 °C
5%
85%
–
10 °C/minute
–40 °C
85 °C
Storage temperature and humidity
–
85 °C at 85%
ESD: Module integrated into system Components[6]
–
15 kV Air
2.0 kV Contact
Storage temperature
ESD and EMI Protection
Exposed components require special attention to ESD and electromagnetic interference (EMI).
A grounded conductive layer inside the device enclosure is suggested for EMI and ESD performance. Any openings in the enclosure
near the module should be surrounded by a grounded conductive layer to provide ESD protection and a low-impedance path to ground.
Device Handling: Proper ESD protocol must be followed in manufacturing to ensure component reliability.
Note
6. This does not apply to the RF pins (ANT).
Document Number: 002-23993 Rev. **
Page 40 of 49
PRELIMINARY
CYBT-483039-02
Regulatory Information
FCC
FCC NOTICE:
The device CYBT-483039-02 complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter
approval as detailed in FCC public Notice DA00-1407.transmitter Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION:
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by
Cypress Semiconductor may void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,ê may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
LABELING REQUIREMENTS:
The Original Equipment Manufacturer (OEM) must ensure that FCC labelling requirements are met. This includes a clearly visible
label on the outside of the OEM enclosure specifying the appropriate Cypress Semiconductor FCC identifier for this product as well
as the FCC Notice above. The FCC identifier is FCC ID: WAP3039.
In any case the end product must be labeled exterior with “Contains FCC ID: WAP3039”.
ANTENNA WARNING:
This device is tested with a standard SMA connector and with the antenna listed in Table 7 on page 15. When integrated in the OEMs
product, this fixed antenna requires installation preventing end-users from replacing them with non-approved antennas. Any antenna
not in Table 7 on page 15 must be tested to comply with FCC Section 15.203 for unique antenna connectors and Section 15.247 for
emissions.
RF EXPOSURE:
To comply with FCC RF Exposure requirements, the Original Equipment Manufacturer (OEM) must ensure to install the approved
antenna in the previous.
The preceding statement must be included as a CAUTION statement in manuals, for products operating with the approved antennas
in Table 7 on page 15, to alert users on FCC RF Exposure compliance. Any notification to the end user of installation or removal
instructions about the integrated radio module is not allowed.
SAR is not required for this module as long as the distance is higher than 33mm away from user.
End users may not be provided with the module installation instructions. OEM integrators and end users must be provided with
transmitter operating conditions for satisfying RF exposure compliance.
Document Number: 002-23993 Rev. **
Page 41 of 49
PRELIMINARY
CYBT-483039-02
ISED
Innovation, Science and Economic Development (ISED) Canada Certification
CYBT-483039-02 is licensed to meet the regulatory requirements of Innovation, Science and Economic Development (ISED) Canada.
License: IC: 7922A-3039
Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure
compliance for SAR and/or RF exposure limits. Users can obtain Canadian information on RF exposure and compliance from
www.ic.gc.ca.
This device has been designed to operate with the antennas listed in Table 7 on page 15, having a maximum gain of 2.3 dBi. Antennas
not included in Table 7 on page 15 or having a gain greater than 2.3 dBi are strictly prohibited for use with this device. The required
antenna impedance is 50 ohms. The antenna used for this transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
ISED NOTICE:
The device CYBT-483039-02 including the built-in trace antenna complies with Canada RSS-GEN Rules. The device meets the
requirements for modular transmitter approval as detailed in RSS-GEN. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This device must accept any interference received, including interference that
may cause undesired operation.
L'appareil CYBT-483039-02, y compris l'antenne intégrée, est conforme aux Règles RSS-GEN de Canada. L'appareil répond aux
exigences d'approbation de l'émetteur modulaire tel que décrit dans RSS-GEN. L'opération est soumise aux deux conditions
suivantes: (1) Cet appareil ne doit pas causer d'interférences nuisibles, et (2) Cet appareil doit accepter toute interférence reçue, y
compris les interférences pouvant entraîner un fonctionnement indésirable.
ISED INTERFERENCE STATEMENT FOR CANADA
This device complies with Innovation, Science and Economic Development (ISED) Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme à la norme sur l'innovation, la science et le développement économique (ISED) norme RSS exempte de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
ISED RADIATION EXPOSURE STATEMENT FOR CANADA
The antenna of this transmitter must provide a separation distance of at least 35 mm from all persons. Installers and end-users
must be provided with antenna installation instructions and transmitter operating conditions and instructions for satisfying RF
exposure compliance.
Compliance of this device in all final product configurations is the responsibility of the Grantee.
Installation of this device into specific final products may require the submission of a Class II permissive change application,
containing data pertinent to RF Exposure, emissions and host/module authentication, or new application if appropriate. The final
product operating with this transmitter must include operating instructions and antenna installation instructions, for end-users and
installers to satisfy RF exposure compliance requirements.
L'antenne de cet émetteur doit fournir une distance de séparation d'au moins 35 mm par rapport à toutes les personnes. Les
installateurs et les utilisateurs finaux doivent recevoir les instructions d'installation de l'antenne ainsi que les conditions d'utilisation
de l'émetteur et les instructions pour satisfaire à la conformité à l'exposition aux radiofréquences.
La conformité de cet appareil dans toutes les configurations de produit final est la responsabilité du bénéficiaire.
L'installation de cet appareil dans des produits finaux spécifiques peut nécessiter la soumission d'une demande de modification
permissive de classe II, contenant des données pertinentes sur l'exposition RF, les émissions et l'authentification hôte / module,
ou une nouvelle application, le cas échéant. Le produit final fonctionnant avec cet émetteur doit inclure des instructions d'utilisation
et des instructions d'installation de l'antenne, pour les utilisateurs finaux et les installateurs afin de satisfaire aux exigences de
conformité en matière d'exposition aux RF.
Document Number: 002-23993 Rev. **
Page 42 of 49
PRELIMINARY
CYBT-483039-02
LABELING REQUIREMENTS:
The Original Equipment Manufacturer (OEM) must ensure that ISED labelling requirements are met. This includes a clearly visible
label on the outside of the OEM enclosure specifying the appropriate Cypress Semiconductor IC identifier for this product as well as
the ISED Notices above. The IC identifier is 7922A-3039. In any case, the end product must be labeled in its exterior with "Contains
IC:7922A-3039".
Le fabricant d'équipement d'origine (OEM) doit s'assurer que les exigences d'étiquetage ISED sont respectées. Cela comprend une
étiquette clairement visible à l'extérieur de l'enceinte OEM spécifiant l'identifiant Cypress Semiconductor IC approprié pour ce produit
ainsi que l'avis ISED ci-dessus. L'identificateur IC est 7922A-3039. En tout cas, le produit final doit être étiqueté dans son extérieur
avec
"Contient IC: 7922A-3039".
European Declaration of Conformity
Hereby, Cypress Semiconductor declares that the Bluetooth module CYBT-483039-02 complies with the essential requirements and
other relevant provisions of Directive 2014. As a result of the conformity assessment procedure described in Annex III of the Directive
2014, the end-customer equipment should be labeled as follows:
All versions of the CYBT-483039-02 in the specified reference design can be used in the following countries: Austria, Belgium, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, The Netherlands, the United Kingdom, Switzerland, and Norway.
MIC Japan
More Part Numbers is certified as a module with certification number TBD. End products that integrate More Part Numbers do not
need additional MIC Japan certification for the end product.
End product can display the certification label of the embedded module.
Document Number: 002-23993 Rev. **
Page 43 of 49
PRELIMINARY
CYBT-483039-02
Packaging
Table 32. Solder Reflow Peak Temperature
Module Part Number
Package
CYBT-483039-02
34-pad SMT
Maximum Peak Temperature Maximum Time at Peak Temperature No. of Cycles
260 °C
30 seconds
Table 33. Package Moisture Sensitivity Level (MSL), IPC/JEDEC J-STD-2
Module Part Number
Package
MSL
CYBT-483039-02
34-pad SMT
MSL 3
The CYBT-483039-02 is offered in tape and reel packaging. Figure 20 details the tape dimensions used for the CYBT-483039-02.
Figure 20. CYBT-483039-02 Tape Dimensions
Figure 21 details the orientation of the CYBT-483039-02 in the tape as well as the direction for unreeling.
Figure 21. Component Orientation in Tape and Unreeling Direction (TBD)
Document Number: 002-23993 Rev. **
Page 44 of 49
PRELIMINARY
CYBT-483039-02
Figure 22 details reel dimensions used for the CYBT-483039-02.
Figure 22. Reel Dimensions
The CYBT-483039-02 is designed to be used with pick-and-place equipment in an SMT manufacturing environment. The
center-of-mass for the CYBT-483039-02 is detailed in Figure 23.
Figure 23. CYBT-483039-02 Center of Mass (TBD)
Document Number: 002-23993 Rev. **
Page 45 of 49
PRELIMINARY
CYBT-483039-02
Ordering Information
Table 34 lists the CYBT-483039-02 part number and features. Table 34 also lists the target program for the respective module ordering
codes. Table 35 lists the reel shipment quantities for the CYBT-483039-02.
Table 34. Ordering Information
Ordering Part
Number
Max CPU Flash RAM
Speed
Size Size UART I2C
(MHz)
(KB) (KB)
CYBT-483039-02
96
1024
512
Yes
Yes
SPI
I2S
ADC
PCM PWM Inputs
Yes
Yes
Yes
10
GPIOs Package
15
Packaging
34-SMT Tape and Reel
Table 35. Tape and Reel Package Quantity and Minimum Order Amount
Description
Minimum Reel Quantity
Maximum Reel Quantity
Comments
Reel Quantity
500
500
Minimum Order Quantity (MOQ)
500
–
–
Order Increment (OI)
500
–
–
Ships in 500 unit reel quantities.
The CYBT-483039-02 is offered in tape and reel packaging. The CYBT-483039-02 ships in a reel size of 500 units.
For additional information and a complete list of Cypress Semiconductor Bluetooth products, contact your local Cypress sales
representative. To locate the nearest Cypress office, visit our website.
U.S. Cypress Headquarters Address
U.S. Cypress Headquarter Contact Info
Cypress website address
Document Number: 002-23993 Rev. **
198 Champion Court, San Jose, CA 95134
(408) 943-2600
http://www.cypress.com
Page 46 of 49
PRELIMINARY
CYBT-483039-02
Acronyms
Document Conventions
Table 36. Acronyms Used in this Document
Units of Measure
Acronym
BLE
Description
Table 37. Units of Measure
Bluetooth Low Energy
Symbol
Unit of Measure
Bluetooth SIG Bluetooth Special Interest Group
°C
degree Celsius
CE
European Conformity
kV
kilovolt
CSA
Canadian Standards Association
mA
milliamperes
EMI
electromagnetic interference
mm
millimeters
ESD
electrostatic discharge
mV
millivolt
FCC
Federal Communications Commission
microamperes
GPIO
general-purpose input/output
μA
μm
ISED
Innovation, Science and Economic Development (Canada)
MHz
megahertz
IDE
integrated design environment
KC
Korea Certification
MIC
Ministry of Internal Affairs and Communications
(Japan)
PCB
printed circuit board
RX
receive
QDID
qualification design ID
SMT
surface-mount technology; a method for
producing electronic circuitry in which the
components are placed directly onto the surface
of PCBs
TCPWM
timer, counter, pulse width modulator (PWM)
TUV
Germany: Technischer Überwachungs-Verein
(Technical Inspection Association)
TX
transmit
Document Number: 002-23993 Rev. **
micrometers
GHz
gigahertz
volt
Page 47 of 49
PRELIMINARY
CYBT-483039-02
Document History Page
Document Title: CYBT-483039-02 EZ-BT™ XR WICED® Module
Document Number: 002-23993
Revision
**
ECN
Orig. of Submission
Change
Date
DSO
Description of Change
05/17/2018 Preliminary datasheet for CYBT-483039-02 module.
Document Number: 002-23993 Rev. **
Page 48 of 49
PRELIMINARY
CYBT-483039-02
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
PSoC® Solutions
Products
ARM® Cortex® Microcontrollers
Automotive
cypress.com/arm
cypress.com/automotive
Clocks & Buffers
Interface
cypress.com/clocks
cypress.com/interface
Internet of Things
Memory
cypress.com/iot
cypress.com/memory
Microcontrollers
cypress.com/mcu
PSoC
cypress.com/psoc
Power Management ICs
Touch Sensing
USB Controllers
Wireless Connectivity
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6
Cypress Developer Community
Forums | WICED IOT Forums | Projects | Video | Blogs |
Training | Components
Technical Support
cypress.com/support
cypress.com/pmic
cypress.com/touch
cypress.com/usb
cypress.com/wireless
© Cypress Semiconductor Corporation, 2018. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document, including
any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide.
Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual
property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby
grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and
reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either
directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as provided
by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the
Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent
permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any
product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is
the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products
are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or
systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the
device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device or system whose failure to perform can be reasonably
expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim,
damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other
liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in
the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 002-23993 Rev. **
Revised May 22, 2018
Page 49 of 49

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-701
Create Date                     : 2017:01:26 11:24:31Z
Creator Tool                    : FrameMaker 7.0
Modify Date                     : 2018:06:07 14:40:32+08:00
Metadata Date                   : 2018:06:07 14:40:32+08:00
Format                          : application/pdf
Description                     : Datasheet
Title                           : CYBT-013033-01 EZ-BT™ Module
Creator                         : DSO
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Copyright                       : Cypress
Document ID                     : uuid:0e4d8029-161d-4c8e-8ea7-57adde37cf19
Instance ID                     : uuid:45cc3355-b18c-4f70-bbd1-a446c480f7b0
Has XFA                         : No
Page Count                      : 49
Subject                         : Datasheet
Author                          : DSO
Keywords                        : CYBT-013033-01, EZ-BT, Module, Datasheet

EXIF Metadata provided by EXIF.tools