D Link DI-764 Multimode 2.4/5GHz Wireless Router User Manual di764 manual 104

D Link Corporation Multimode 2.4/5GHz Wireless Router di764 manual 104

Contents

Part 1

2.4 GHz / 5 GHz MultimodeManualBuilding Networks for People AirPro DI-764Wireless Broadband RouterD-LINK
2ContentsPackage Contents ................................................................................3Introduction ..........................................................................................4Wireless Basics ....................................................................................6Getting Started ...................................................................................10Using the Configuration Menu ............................................................12Networking Basics ..............................................................................41Troubleshooting ..................................................................................70Technical Specifications .....................................................................76Contacting Technical Support.............................................................79Warranty and Registration ..................................................................80
3Contents of Package:D-Link AirPro DI-764 2.4GHz/5GHz Multimode WirelessBroadband RouterPower Adapter – 5V DC, 3.0AManual on CDQuick Installation GuideEthernet CablePackage Contents Computer with Windows, Macintosh, or Linux-basedoperating system with an installed Ethernet adapterNote: Using a power supply with a different voltage rating than the one included with theDI-764 will cause damage and void the warranty for this product.If any of the above items are missing, please contact your reseller.System Requirements For Configuration:!!!!!!
4IntroductionD-Link, a leader in wireless technology, introduces the first integratedmultimode 2.4GHz/5GHz wireless broadband router, as part of the highperformance D-Link AirPro series of wireless networking products.The new D-Link AirPro DI-764 Multimode Wireless Broadband Router is anext generation multimode broadband router that simultaneously servesboth 802.11a wireless networks at 54 Mbps (72 Mbps in Turbo mode*) and802.11b wireless networks at 11Mbps (22 Mbps with D-Link AirPlusproducts.) Featuring a breakthrough all-in-one dual band design thatdelivers future investment protection with the promise of a superior productlife cycle and lower total cost of ownership, it is the ideal solution for presentand future Wireless Local Area Networks (WLANs).The DI-764 will automatically obtain an IP address and forward additional IPaddresses to multiple clients for a seamless Ethernet network connectionand shared Internet access.At 54Mbps (up to 72Mbps in Turbo mode*) in the 5GHz frequency range anda simultaneous 11 Mbps (up to 22 Mbps with D-Link AirPlus products) in the2.4GHz frequency range, the D-Link AirPro DI-764 multimode broadbandrouter delivers the fastest standards-based wireless technology in theindustry. Based on WiFi technology, as well as IEEE 802.11a and 802.11bstandards compliant, this next-generation multimode wireless access pointprovides excellent network interoperability.Armed with powerful management and security capabilities, the D-Link AirPro DI-764 has an intuitive and secure web-based interface that is poweredby an embedded web server.After completing the steps outlined in the Quick Installation Guide (includedin your package) not only will you have the ability to share information andresources, but you will also be able to enjoy the freedom that wirelessnetworking delivers, at speeds capable of handling a video stream.*When used with other D-Link AirPro products.
5Because of its web-based interface (accessible from most Internet browser applications),the DI-764 will work with most popular operating systems, including Macintosh, Linuxand Windows, and can be easily integrated into a large network. This Manual is designedto help you connect the DI-764 with the D-Link 2.4GHz AirPlus or 5GHz AirPro WirelessAdapters into an existing network. Please take a look at the Getting Started section inthis manual to see an example of an Infrastructure network using the DI-764.ConnectionsFeatures & BenefitsSupports data transfer rates of up to 72 Mbps at 5GHzSupports data transfer rates of up to 22 Mbps at 2.4GHzWireless range of up to 900 feet*Fully 802.11a and 802.11b compatibleSupports up to 256-bit WEP Encryption at 2.4GHz, and up to 152-bit, withEnhanced Dynamic Keying at 5 GHzLess interference with a total of eleven non-overlapping channelsUtilizes Direct Sequence Spread Spectrum (DSSS) and Packet BinaryConvolutional Code (PBCC) at 2.4GHzUtilizes Orthogonal Frequency Division Multiplexing (OFDM) at 5GHz!!!!!!!!Easy-to-use Web-based configurationUser level security3 Year Warranty (USA only)!!!Pressing theReset Buttonrestores therouter to itsoriginal factorydefault settings.Receptorfor thePowerAdapterThe WAN port is theconnection for theEthernet cable to theCable or DSL modemLAN ports automaticallysense cable type whenconnecting to Ethernet-enabled computers.*Environmental Factors may Adversely Affect Range.
6LEDSLED stands for Light-Emitting Diode. The DI-764 has the following LEDs:D-Link AirPro wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business orpublic access wireless networks. Strictly adhering to the IEEE standard, the D-LinkAirPro wireless family of products will allow you to securely access the data youwant, when and where you want it. You will be able to enjoy the freedom thatwireless networking delivers.A wireless local area network (WLAN) is a cellular computer network that transmitsand receives data with radio signals instead of wires. Wireless LANs are usedincreasingly in both home and office environments, and public areas such asairports, coffee shops and universities. Innovative ways to utilize WLAN technologyare helping people to work and communicateWireless BasicsLED LED ActivityA steady light indicates a connection to a power sourceA solid light indicates that the unit is defectiveA solid light indicates connection on the WAN port.This LED blinks during data transmission.A solid light indicates that the 802.11a wireless seg-ment is ready. The LED blinks during 802.11a wirelessdata transmission.A solid light indicates that the DI-764 is readyA solid light indicates a connection, a blinking lightindicates data transmission to an Ethernet-enabledcomputer on ports 1-4.PowerM1M2WAN WLAN802.11aLocal Network(Ports 1-4) WLAN802.11bA solid light indicates that the 802.11b wireless seg-ment is ready (when the DWL-650+ is installed.) TheLED blinks during 802.11b wireless data transmission.
7Wireless Basicsmore efficiently. Increased mobility and the absence of cabling and otherfixed infrastructure have proven to be beneficial for many users.Wireless users can use the same applications they use on a wired network.Wireless adapter cards used on laptop and desktop systems support thesame protocols as Ethernet adapter cards.Under many circumstances, it may be desirable for mobile network devicesto link to a conventional Ethernet LAN in order to use servers, printers or anInternet connection supplied through the wired LAN. A Wireless Router is adevice used to provide this link.People use wireless LAN technology for many different purposes:Mobility - Productivity increases when people have access to data in anylocation within the operating range of the WLAN. Management decisionsbased on real-time information can significantly improve worker efficiency.Low Implementation Costs – WLANs (Wireless Local Area Networks)are easy to set up, manage, change and relocate. Networks that frequentlychange, both physically and logically, can benefit from WLANs ease ofimplementation. WLANs can operate in locations where installation of wiringmay be impractical.Installation Speed and Simplicity - Installing a wireless LAN systemcan be fast and easy and can eliminate the need to pull cable through wallsand ceilings.Network Expansion - Wireless technology allows the network to go wherewires cannot go.Scalability – Wireless Local Area Networks (WLANs) can be configured ina variety of topologies to meet the needs of specific applications andinstallations. Configurations are easily changed and range from peer-to-peernetworks suitable for a small number of users to larger infrastructurenetworks to accommodate hundreds or thousands of users, depending onthe number of wireless devices deployed.
8Wireless BasicsThe DI-764 is compatible with other D-Link AirPro 802.11a products, whichinclude:♦5GHz Wireless Cardbus Adapters used with laptop computers(DWL-A650)♦5GHz Wireless PCI Adapters used with desktop computers(DWL-A520)The DI-764 is also compatible with the D-Link AirPlus 802.11b wireless family,which includes:♦Enhanced 2.4GHz Wireless Cardbus Adapters used with laptopcomputers (DWL-650+)♦Enhanced 2.4GHz Wireless PCI cards used with desktop computers(DWL-520+)Standards-Based TechnologyThe versatile DI-764 Multimode Wireless Broadband Router integrates both802.11a and 802.11b standards into a single unit.The IEEE 802.11a standard designates that devices may operate at anoptimal data rate of 54 Mbps (72 Mbps in proprietary Turbo mode.) Thismeans that in most environments, within the specified range of this device,you will be able to transfer large files quickly or even watch a movie inMPEG format over your network without noticeable delays. This technologyworks by transmitting high-speed digital data over a radio wave utilizingOFDM (Orthogonal Frequency Division Multiplexing) technology. OFDMworks by splitting the radio signal into multiple smaller sub-signals that arethen transmitted simultaneously at different frequencies to the receiver.OFDM reduces the amount of crosstalk (interference) in signaltransmissions. D-Link AirPro 802.11a products will automatically sense thebest possible connection speed to ensure the greatest speed and rangepossible.Based on the IEEE 802.11b standard, the DI-764 is also interoperable withexisting compatible 2.4GHz wireless technology with data transfer speeds ofup to 22Mbps (with the D-Link AirPlus family of wireless devices,) as well asstandard 802.11b technology ( the D-Link Air family of wireless devices),with speeds of up to 11Mbps.
9Wireless BasicsInstallation ConsiderationsThe D-Link AirPro DI-764 lets you access your network, using a wirelessconnection, from virtually anywhere. Keep in mind, however, that thenumber, thickness and location of walls, ceilings or other objects that thewireless signals must pass through may limit the range. Typical ranges varydepending on the types of materials and background RF (radio frequency)noise in your home or business. The key to maximizing wireless range is tofollow these basic guidelines:1. Keep the number of walls and ceilings between the DI-764 and your receiving device (e.g., the DWL-A650 or the DWL-650+) to a minimum - each wall or ceiling can reduce your D-Link AirPro Wireless product’s range from 3-90 feet (1-30 meters.) Position your receiving devices so that the number of walls or ceilings is minimized.2. Be aware of the direct line between routers and computers. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Try to make sure that devices are positioned so that the signal will travel straight through a wall or ceiling for better reception.3. Building Materials make a difference - a solid metal door or aluminum studs may have a negative effect on range. Try to position wireless devices and computers with wireless adapters so that the signal passes through drywall or open doorways and not other materials.4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF noise.
10With a single IP Address from your Broadband Internet Service provider youcan share the Internet with all the computers on your local network, withoutsacrificing speed or security, using D-Link Air networking products.Getting StartedAn Infrastructure wireless network contains an Access Point. TheInfrastructure Network example, shown here, contains the following D-Linknetwork devices:A wireless Broadband Router - D-Link AirPro DI-764A laptop computer with a wireless adapter - D-Link AirPro DWL-A650 orAirPlus DWL-650+A desktop computer with a wireless adapter - D-Link AirPro DWL-A520 orAirPlus DWL-520+A Cable modem - D-Link DCM-200If you need to assign IP Addresses to the computers on the network,please remember that the IP Address for each computer must be inthe same IP Address range as all the computers in the network, andthe Subnet mask must be exactly the same for all the computers in thenetwork.For example: If the first computer is assigned an IP Address of192.168.0.2 with a Subnet Mask of 255.255.255.0, then the secondcomputer can be assigned an IP Address of 192.168.0.3 with a SubnetMask of 255.255.255.0, etc.IMPORTANT: If computers or other devices are assigned the sameIP Address, one or more of the devices may not be visible on thenetwork.IP ADDRESSNote: If you are using a DHCP-capable router in your network setup,such as the DI-764, you will not need to assign a static IP Address.Right out of the box, with its default settings, the DI-764 willconnect with other D-Link Air, AirPlus or AirPro products.
11Please remember that D-Link AirPro wireless devices are pre-configured to connecttogether, right out of the box, with the default settings.You will need broadband Internet access (Cable/DSL) subscriptionConsult with your Cable/DSL provider for proper installation of the modemConnect the modem to the DI-764 multimode wireless broadband router(see the Quick Installation Guide included with the DI-764.)If you are connecting a desktop computer to your network, you can install theD-Link AirPro DWL-A520 (or the DWL-520+) wireless PCI adapter into anavailable PCI slot. (See the Quick Installation Guide included with the DWL-A520 or the DWL-520+.)If you are connecting a laptop computer to your network, install the drivers for thewireless cardbus adapter (D-Link AirPro DWL-A650) into a laptop computer .(See the Quick Installation Guide included with DWL-A650 or DWL-650+.)Getting StartedFor a typical wireless setup at home (as shown above), please do thefollowing:51342
12Using the Configuration MenuWhenever you want to configure your network or the DI-764, you can access theConfiguration Menu by opening the web-browser and typing in the IP Address of theDI-764. The DI-764 default IP Address is shown below: !Open the web browser !Type in the IP Address ofthe Access Point!Type admin in the User Name fieldLeave the Password blankClick NextHome > WizardThe Home>Wizard screen will appear. Please refer to the Quick InstallationGuide for more information regarding the Setup Wizard.http://192.168.0.1Connect to 192.168.0.1adminNote: if you have changed the default IP Address assigned to the DI-764, make sure toenter the correct IP Address.!!
13Home > Wireless > 802.11aUsing the Configuration MenuSSID-Channel-Wireless Settings- choose 802.11a or 802.11b+. Here, 802.11a is selected.“default” is the default setting. All devices on the network mustshare the same SSID. If you change the default setting, theSSID may be up to 32 characters long.52 is the default channel for 802.11a. All devices on the net-work must share the same channel.Hexadecimal digits consist of the numbers 0-9 and the letters A-FASCII (American Standard Code for Information Interchange) is a code forrepresenting English letters as numbers from 0-127Apply- click Apply to save the changes.Keys 1-4- input up to 4 WEP keys; select the one you wish to use.Key Type- select HEX or ASCIIWEP Encryption- select the level of encryption desired: 64, 128 or 152-bitWEP- select Enabled or Disabled. Disabled is the default setting.Turbo Mode- select ON or OFF. The default setting is OFF.If you enable Turbo mode on the DI-764, make sure to also enable Turbomode on all 802.11a wireless clients or a wireless connection will not beestablished.WEP (Wired Equivalent Privacy) If you enable encryption on the DI-764make sure to also enable encryption on all 802.11a wireless clients orwireless connection will not be established.
14Using the Configuration MenuHome > Wireless > 802.11b+Apply- click Apply to save the changes.Keys 1-4- input up to 4 WEP keys; select the one you wish to use.Passphrase- when you select Key Type: ASCII, you can enter a Passphrasefor any or all of Keys 1-4Key Type- select HEX or ASCIIWEP Encryption- select the level of encryption desired: 64, 128 or 256-bitWEP- select Enabled or Disabled. Disabled is the default setting.Channel- 6 is the default channel for 802.11b+. All devices on the net-work must share the same channel.SSID- “default” is the default setting. All devices on the network mustshare the same SSID. The SSID may be up to 32 characterslong.Wireless Settings- choose 802.11a or 802.11b+. Here, 802.11b+ is selected.WEP (Wired Equivalent Privacy) If you enable encryption on the DI-764make sure to also enable encryption on all 802.11b wireless clients orwireless connection will not be established.
15Using the Configuration MenuHome > WAN > Dynamic IP AddressDynamicIP Address-Host Name-MAC Address-CloneMAC Address-Apply-Please besure toremove anyexistingPPPoE clientsoftwareinstalledon yourcomputers. most Cable modem users will select this option to obtain an IPAddress automatically from their ISP (Internet Service Pro-vider).this is optional, but may be required by some ISPs. The hostname is the device name of the Router.the default MAC Address is set to the WAN’s physical interfaceMAC address on the Router.copy the MAC address of the Ethernet card installed by yourISP, and replace the WAN MAC address with this Ethernet cardMAC address. It is not recommended that you change the de-fault MAC address unless required by your ISP.click Apply to save the changes.
16Using the Configuration MenuHome > WAN > Static IP AddressStatic IP Address- IP Address-Subnet Mask-ISPGateway Address-PrimaryDNS Address-SecondaryDNS Address-Apply-select this option to set static IP information provided to you byyour ISP. input the IP Address provided by your ISPinput your Subnet mask. (All devices in the network must havethe same subnet mask.) input the Gateway addressinput the address provided by your ISPthis is optionalclick Apply to save the changes.
17Using the Configuration MenuHome > WAN > PPPoEPPPoE-Static PPPoE-you have an assigned (static) IP Address.Choose this option if your ISP uses PPPoE. (Most DSL userswill select this option.)Dynamic PPPoE- receive an IP Address automatically fromyour ISP.orUser Name- your PPPoE username provided by your ISP.Password- your PPPoE password provided by your ISP.Retype Password- re-enter the PPPoE passwordService Name- enter the Service Name provided by your ISP (optional).IP Address- this option is only available for Static PPPoE. Enter the staticIP Address for the PPPoE connection.
18Using the Configuration MenuHome > WAN > PPPoE continuedHome > LANLAN is short for Local Area Network. This is considered your internal network. Theseare the IP settings of the LAN interface for the DI-764. These settings may be referredto as Private settings. You may change the LAN IP address if needed. The LAN IPaddress is private to your internal network and cannot be seen on the Internet.Apply- click Apply to save the changes.Auto-reconnect- if enabled, the DI-764 will automatically connect to your ISPafter your system is restarted or if the connection is dropped.MTU- Maximum Transmission Unit-1472 is default-you may need tochange the MTU to conform with your ISP.MaximumIdle Time- enter a maximum idle time during which internet connection ismaintained during inactivity. To disable this feature, enter zeroor enable Auto-reconnect.SecondaryDNS Address- optionalPrimaryDNS Address- get this info from your ISPApply- click Apply to save the changes.Local optionalSubnet Mask- the subnet mask of the LAN interface.The default subnet mask is 255.255.255.0IP Address- the IP address of the LAN interface. The default IP address is:192.168.0.1
19Using the Configuration MenuHome > DHCPDHCP stands for Dynamic Host Control Protocol. The DI-764 has a built-in DHCPserver. The DHCP Server will automatically assign an IP address to the computers onthe LAN/private network. Be sure to set your computers to be DHCP clients by settingtheir TCP/IP settings to “Obtain an IP Address Automatically.” When you turn yourcomputers on, they will automatically load the proper TCP/IP settings provided by theDI-764. The DHCP Server will automatically allocate an unused IP address from the IPaddress pool to the requesting computer. You must specify the starting and endingaddress of the IP address pool.DHCP Server- select Enabled or DisabledStartingIP Address- the starting IP address for the DHCP server’s IP assignmentEndingIP Address- the ending IP address for the DHCP server’s IP assignmentLease Time- enter the Lease timeApply- click Apply to save the changes
20Advanced > Virtual ServerUsing the Configuration MenuThe DI-764 can be configured as a virtual server so that remote users accessingWeb or FTP services via the public IP address can be automatically redirected tolocal servers in the LAN (Local Area Network).The DI-764 firewall feature filters out unrecognized packets to protect your LANnetwork so all computers networked with the DI-764 are invisible to the outsideworld. If you wish, you can make some of the LAN computers accessible from theInternet by enabling Virtual Server. Depending on the requested service, the DI-764redirects the external service request to the appropriate server within the LANnetwork.
21Advanced > Virtual Server continuedUsing the Configuration MenuThe DI-764 is also capable of port-redirection meaning incoming traffic to a particularport may be redirected to a different port on the server computer.Each virtual service that is created will be listed at the bottom of the screen in theVirtual Servers List. There are pre-defined virtual services already in the table. Youmay use them by enabling them and assigning the server IP to use that particularvirtual service.Example #1:If you have a Web server that you wanted Internet users to access at all times, youwould need to enable it. Web (HTTP) server is on LAN (Local Area Network)computer 192.168.0.25. HTTP uses port 80, TCP.Name: Web ServerPrivate IP: 192.168.0.25Protocol Type: TCPPrivate Port: 80Public Port: 80Schedule: alwaysProtocol Type- the protocol used for the virtual servicePublic Port- the port number on the WAN (Wide Area Network)side that willbe used to access the virtual service.Private Port- the port number of the service used by the Private IP computerSchedule- The schedule of time when the virtual service will beenabled. The schedule may be set to Always, which willallow the particular service to always be enabled. If it is set toTime, select the time frame for the service to be enabled. Ifthe system time is outside of the scheduled time, the servicewill be disabled.Apply- click Apply to save the changes.Virtual Server- select Enabled or DisabledName- enter the name referencing the virtual servicePrivate IP- the server computer in the LAN (Local Area Network) that willbe providing the virtual services.
22 Example #2:If you have an FTP server that you wanted Internet users to access by WAN port2100 and only during the weekends, you would need to enable it as such. FTPserver is on LAN computer 192.168.0.30. FTP uses port 21, TCP.Name: FTP ServerPrivate IP: 192.168.0.30Protocol Type: TCPPrivate Port: 21Public Port: 2100Schedule: From: 01:00AM to 01:00AM, Sat to SunUsing the Configuration MenuAdvanced > Virtual Server continuedClick on this icon to edit the virtual serviceClick on this icon to delete the virtual serviceAll Internet users who want to access this FTP Servermust connect to it from port 2100. This is an example ofport redirection and can be useful in cases where thereare many of the same servers on the LAN network.
23Using the Configuration MenuAdvanced > ApplicationsSome applications require multiple connections, such as Internet gaming, videoconferencing, Internet telephony and others. These applications have difficultiesworking through NAT (Network Address Translation). Special Applications makessome of these applications work with the DI-764. If you need to run applications thatrequire multiple connections, specify the port normally associated with an applicationin the “Trigger Port” field, select the protocol type as TCP or UDP, then enter thepublic ports associated with the trigger port to open them for inbound traffic.The DI-764 provides some predefined applications in the table on the bottom of theweb page. Select the application you want to use and enable it.Note! Only one PC can use each Special Application tunnel.Name: this is the name referencing the special application.Trigger Port: this is the port used to trigger the application. It can be eithera single port or a range of ports.Trigger Type: this is the protocol used to trigger the special application.Public Port: this is the port number on the WAN side that will be used toaccess the application. You may define a single port or arange of ports. You can use a comma to add multiple ports orport ranges.Public Type: this is the protocol used for the special application.Apply: click Apply to save the changes
24Using the Configuration MenuAdvanced > Filters > IP FiltersFilters are used to deny or allow LAN (Local Area Network) computers from accessingthe Internet. The DI-764 can be setup to deny internal computers by their IP or MACaddresses. The DI-764 can also block users from accessing restricted web sites.click Apply to save changes.Apply:this is the schedule of time when the IP Filter will be enabled.Schedule:select the protocol typeProtocol Type:the single port or port range that will be denied access to theInternet.Port:Use IP Filters to deny LAN IP addresses from accessing theInternet. You can deny specific port numbers or all ports forthe specific IP address.IP Filtersthe IP address of the LAN computer that will be deniedaccess to the Internet.IP:
25Using the Configuration MenuAdvanced > Filters > URL BlockingFilters-URL Blocking is used to deny LAN computers from accessing specific web sites byits URL. A URL is a specially formatted text string that defines a location on theInternet. If any part of the URL contains the blocked word, the site will not beaccessible and the web page will not display.select the filter you wish to use; in this case, URL Blockingwas chosen.Apply- click Apply to save the changes.Keywords- block URLs which contain keywords listed below.Enter the keywords in this space.URL Blocking- select Enabled or Disabled.
26Using the Configuration MenuAdvanced > Filters > MAC FiltersUse MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network)computers by their MAC addresses from accessing the Internet. You can eithermanually add a MAC address or select the MAC address from the list of clients thatare currently connected to the Broadband Router.MAC Filters- choose Disable MAC filters; allow MAC addresses listed be-low; or deny MAC addresses listed below.Filters- select the filter you wish to use; in this case, MAC filters waschosen.Name- enter the name here.MAC Address- enter the MAC Address.DHCP Client- select a DHCP client from the pull-down list; click Clone to copythat MAC AddressApply- click Apply to save the changes.
27Using the Configuration MenuAdvanced > Filters > Domain BlockingFilters-Domain Blocking:Blocked Domains-PermittedDomains-Apply-Domain Blocking is used to allow or deny LAN (Local Area Network) computers fromaccessing specific domains on the Internet. Domain blocking will deny all requests to aspecific domain such as http and ftp. It can also allow computers to access specificsites and deny all other sites.select the filter you wish to use; in this case, Domain Blockingwas chosen.Disabled-Allow-Deny-enter the Permitted Domains in this fieldenter the Blocked Domains in this fieldclick Apply to save the changes.select Disabled to disable Domain Blockingallows users to access all domains except Blocked Domainsdenies users access to all domains exceptPermitted Domains
28Using the Configuration MenuAdvanced > FirewallSchedule-Apply-Firewall Rules is an advanced feature used to deny or allow traffic from passingthrough the DI-764. It works in the same way as IP Filters with additional settings.You can create more detailed access rules for the DI-764. When virtual services arecreated and enabled, it will also display in Firewall Rules. Firewall Rules contains allnetwork firewall rules pertaining to IP (Internet Protocol).In the Firewall Rules List at the bottom of the screen, the priorities of the rules arefrom top (highest priority) to bottom (lowest priority.)Note: The DI-764 MAC Address filtering rules have precedence over the FirewallRules.select Always or enter the Time.click Apply to save the changes.Firewall Rules-Name-Action-Source-enable or disable theFirewallenter the nameallow or denyenter the IP Address rangeDestination- enter the IP Address range; the Protocol;and the Port Range
29Advanced > DMZUsing the Configuration MenuIf you have a client PC that cannot run Internet applications properly from behind theDI-764, then you can set the client up to unrestricted Internet access. It allows acomputer to be exposed to the Internet. This feature is useful for gaming purposes.Enter the IP address of the internal computer that will be the DMZ host. Adding aclient to the DMZ (Demilitarized Zone) may expose your local network to a variety ofsecurity risks, so only use this option as a last resort.DMZ-IP Address-Apply-enable or disable the DMZ. The DMZ (Demilitarized Zone)allows a single computer to be exposed to the internet.enter the IP Address of the computer to be in the DMZclick Apply to save the changes.
30Using the Configuration MenuAdvanced > Performance > 802.11aApply- click Apply to save the changesDTIM interval- (Delivery Traffic Indication Message) 1 is the default setting. ADTIM is a countdown informing clients of the next window forlistening to broadcast and multicast messages.RTS Threshold- this value should remain at its default setting of 2342. If incon-sistent data flow is a problem, only a minor modification shouldbe made.Beacon interval- beacons are packets sent by the DI-764 to synchronize a wire-less network. Specify a value. 100 is the default setting and isrecommended.Data Rate- best is the default selectionTransmit Power- full is the default selection.WirelessPerformance- select 802.11a or 802.11b+. Here, 802.11a has beenchosen. This screen displays the wireless performancefeatures of the Access Point portion of the DI-764.Fragmentation- this value should also remain at its default setting of 2346. Ifyou experience a high packet error rate, you may slightly in-crease your Fragmentation value within the range of 256-2346.Setting the Fragmentation value too low may result in poor per-formance.Shared Key - in this mode, in order to access the DI-764 on the network, thedevice must be listed in the MAC Address Control ListOpen System - the DI-764 will be visible to all devices on the network. This isthe default settingAuthentication- select Open system or Shared Key
31Using the Configuration MenuAdvanced > Performance > 802.11b+Beacon interval- beacons are packets sent by the DI-764 to synchronize a wire-less network. Specify a value. 100 is the default setting and isrecommended.Basic Rates- choose from1-2Mbps; 1,2,5.5,11 Mbps; or 1,2,5.5,11,22 MbpsRTS Threshold- this value should remain at its default setting of 2342. If incon-sistent data flow is a problem, only a minor modification shouldbe made.Fragmentation- this value should also remain at its default setting of 2346. Ifyou experience a high packet error rate, you may slightly in-crease your Fragmentation value within the range of 256-2346.Setting the Fragmentation value too low may result in poor per-formance.WirelessPerformance-Select 802.11a or 802.11b+. 802.11b+ is selected here. Dis-played in this window are the Wireless Performance featuresfor the Access Point portion of the DI-764.DTIM interval- (Delivery Traffic Indication Message) 3 is the default setting. ADTIM is a countdown informing clients of the next window forlistening to broadcast and multicast messages.TX Rates- select the basic transfer rates based on the speed of the wire-less adapters on the WLAN (wireless local area network);choose from among the same ranges as those listed in the BasicRates,above.
32Using the Configuration MenuTools> AdminApply- click Apply to save changesShared Key - in this mode, in order to access the DI-764 on the network, thedevice must be listed in the MAC Address Control ListOpen System - the DI-764 will be visible to all devices on the network. This isthe default settingAuthentication- select Open system or Shared KeyPreamble Type- select Short or Long Preamble. The Preamble Type definesthe length of the CRC (Cyclic Redundancy Check) block forcommunication between the DI-764 and roaming wireless adapt-ers. Make sure to select the appropriate preamble type andclick Apply. Note: High network traffic areas should use theshorter preamble type. CRC is a common technique for de-tecting data transmission errors.AdministratorLogin Nameadmin is the default login name for the Admin accountUserLogin Nameuser is the default login name for the User accountAdmin Password- the default setting is blank - no password. To change the pass-word, enter and confirm the new password.User Password- the default setting is blank - no password. To change the pass-word, enter and confirm the new password.
33Using the Configuration MenuTools > TimeRemote ManagementRemote Management allows the DI-764 to be configured from the Internet by a webbrowser. A username and password is still required to access the Web-Managementinterface. In general, only a member of your network can browse the built-in webpages to perform “Administrator” tasks. This feature enables you to perform“Administrator” tasks from the remote (Internet) host.IP Address: Internet IP address of the computer that has access to the Router. It isnot recommended that you set the IP address to * (star), because this allows anyInternet IP address to access the Router, which could result in a loss of security foryour network. If you elect to enable Remote Management, make sure to enter theIP Address of the remote computer allowed to configure the DI-764.Port: For security purposes, select a separate port number used to access theRouter. (The following is an example only; you may use a different port number.)Example: http://x.x.x.x:8080 where x.x.x.x is the WAN IP address of the Routerand 8080 is the port used for the Web-Management interface.DefaultNTP Server-NTP is short for Network Time Protocol. NTP synchronizes com-puter clock times in a network of computers.This field is optional.Time settings- in this window you can choose the time zone; set the time;and enable or disable Daylight Savings Time.
34Using the Configuration MenuTools > SystemSystem Settingsclick Save to save the current settings to the local Hard Driveclick Browse to find the settings, then click LoadSave Settings toLocal Hard Drive-Load Settings fromLocal Hard Drive-Restore to FactoryDefault Settings- click Restore to restore the factory default settings
35Using the Configuration MenuTools > FirmwareFirmware Upgrade-Browse-click on the link in this screen to find out if there is an updatedfirmware; if so, download the new firmware to your hard drive.after you have downloaded the new firmware, click Browse inthis window to locate the firmware update on your hard drive.Click Apply to complete the firmware upgrade.
36Using the Configuration MenuTools > MiscPing Test-Restart Device-Block WAN Ping-Discard Pingfrom WAN side-VPNPass Through-PPTP- select Enabled or DisabledIPSec- select Enabled or DisabledApply-the Ping Test is used to send Ping packets to test if a computeris on the Internet. Enter the IP Address that you wish to Ping,and click Pingif you choose to block WAN Ping, the WAN IP Address of theDI-764 will not respond to pings. Blocking the Ping may providesome extra security from hackers.the DI-764 supports VPN (Virtual Private Network) pass-throughfor both PPTP (Point-to-Point Tunneling Protocol) and IPSec(IP Security). Once VPN pass-through is enabled, there is noneed to open up virtual services. Multiple VPN connectionscan be made through the DI-764. This is useful when you havemany VPN clients on the LAN network.click Reboot to restart the DI-764click Enabled to block the WAN pingclick Apply to save changes
37Using the Configuration MenuStatus > Device InfoDevice Information- This screen displays information about the DI-764
38Using the Configuration MenuStatus > LogView Log-Log Settings-this screen displays the activity on the DI-764for advanced features, click on Log Settings
39Status > WirelessConnectedWirelessClient List-Using the Configuration MenuStatus > StatsTraffic Statistics- displays the receive and transmit packets that are passingthrough the DI-764. Click on Refresh or Reset, for the mostrecent information.displays the wireless clients that are connectedto the Access Point function of the DI-764.
40Using the Configuration MenuHelpHelp- displays the complete Help menu. For help at anytime, clickthe Help tab in the Configuration menu.

Navigation menu