D Link I524I1 Wireless 150 Router User Manual II

D Link Corporation Wireless 150 Router II

Contents

user manual II

618. Resetting the DI-524 to Factory Default SettingsAfter you have tried other methods for troubleshooting your network, you may choose to Reset the DI-524 to the factory default settings. Remember that D-Link AirPro products network together, out of the box, at the factory default settings. To hard-reset the DI-524 to Factory Default Settings, please do the following:Troubleshooting    After the DI-524 reboots (this may take a few minutes) it will be reset to the factory Default settingsUse a paper clip to press the Reset buttonHold for about 10 seconds and then releaseLocate the Reset button on the back of the DI-524Reset
62IP FilteringURL FilteringDomain BlockingSchedulingBased on IEEE 802.11n (draft 2.0) TechnologyIEEE 802.11gIEEE 802.11b IEEE 802.3IEEE 802.3uTechnical SpecicationsL2TPStandardsVPN Pass Through/ Multi-SessionsPPTPDevice ManagementWeb-Based- Internet Explorer v6 or later; Netscape Navigator v7 or later; or other Java-enabled browsersAdvanced Firewall FeaturesNAT with VPN Passthrough (Network Address Translation)95% maximum (non-condensing)Wireless Operating Range Operating Temperature 32ºF to 104ºF (0ºC to 40ºC) Humidity: Indoors – up to 328 feet (100 meters)IPSecDHCP Server and ClientMAC Filtering Outdoors – up to 984 feet (300 meters)Safety and Emissions:FCC, CE2.4GHz to 2.462GHzWireless Frequency Range:
63LEDs:PowerWANPhysical Dimensions:Technical SpecicationsL = 5.6 inches (142mm)W = 4.3 inches (109mm)H = 1.2 inches (31mm)Wireless Transmit Power:15dBm± 5dB Security:802.1xWEP WPA WPA-PSKExternal Antenna Type:Single Fixed AntennaOrthogonal Frequency Division Multiplexing (OFDM)Modulation Technology:Power Input:Ext. Power Supply DC 5V, 1AWeight:0.44 lbs. (200g)LAN (10/100)WLAN (Wireless Connection)Warranty:1 year
64Max physical rate up to 150 Mbps in 802.11n mode54 Mbps48 Mbps36 Mbps24 Mbps18 Mbps12 Mbps11 Mbps9 Mbps6 Mbps5.5 Mbps2 Mbps1 MbpsWireless Data Rates with Automatic Fallback: 54Mbps OFDM, 10% PER, -68dBm48Mbps OFDM, 10% PER, -70dBm36Mbps OFDM, 10% PER, -75dBmReceiver Sensitivity:24Mbps OFDM, 10% PER, -79dBm18Mbps OFDM, 10% PER, -82dBm12Mbps OFDM, 10% PER, -84dBm11Mbps CCK, 8% PER, -82dBm9Mbps OFDM, 10% PER, -86dBm6Mbps OFDM, 10% PER, -88dBm5.5Mbps CCK, 8% PER, -85dBm2Mbps QPSK, 8% PER, -86dBm1Mbps BPSK, 8% PER, -89dBmTechnical Specications
65Frequently Asked Questions When entering the IP Address of the DI-524 (192.168.0.1), you are not connecting to the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to connect to the web-based utility. To resolve difculties accessing a web utility, please follow the steps below. Step1Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may not be on. The following connections require a Crossover Cable:Computer to Computer Computer to Uplink Port Computer to Access Point Computer to Print Server Computer/XBOX/PS2 to DWL-810 Computer/XBOX/PS2 to DWL-900AP+ Uplink Port to Uplink Port (hub/switch) Normal Port to Normal Port (hub/switch) The following connections require a Straight-through Cable:Computer to Residential Gateway/Router Computer to Normal Port (hub/switch) Access Point to Normal Port (hub/switch) Print Server to Normal Port (hub/switch) Uplink Port to Normal Port (hub/switch) Rule of Thumb: ”If there is a link light, the cable is right.” What type of cable should I be using?Why can´t I access the web based conguration?
66Frequently Asked Questions (continued)What type of cable should I be using? (continued)What´s the difference between a crossover cable and a straight-through cable? The wiring in crossover and straight-through cables are different. The two types of cable have different purposes for different LAN congurations. EIA/TIA 568A/568B dene the wiring standards and allow for two different wiring color codes as illustrated in the following diagram. *The wires with colored backgrounds may have white stripes and may be denoted that way in diagrams found elsewhere.How to tell straight-through cable from a crossover cable:The main way to tell the difference between the two cable types is to compare the wiring order on the ends of the cable. If the wiring is the same on both sides, it is straight-through cable. If one side has opposite wiring, it is a crossover cable. All you need to remember to properly congure the cables is the pinout order of the two cable ends and the following rules: A straight-through cable has identical endsA crossover cable has different ends It makes no functional difference which standard you follow for straight-through cable ends, as long as both ends are the same. You can start a crossover cable with either standard as long as the other end is the other standard. It makes no functional difference which end is which. The order in which you pin the cable is important. Using a pattern other than what is specied in the above diagram could cause connection problems. When to use a crossover cable and when to use a straight-through cable:Computer to Computer – Crossover Computer to an normal port on a Hub/Switch – Straight-through Computer to an uplink port on a Hub/Switch - Crossover Hub/Switch uplink port to another Hub/Switch uplink port – Crossover Hub/Switch uplink port to another Hub/Switch normal port - Straight-through Why can´t I access the web based conguration? (continued)
67Step3 Congure your Internet settings. Step2 Disable any Internet security software running on the computer. Software rewalls like Zone Alarm, Black Ice, Sygate, Norton Personal Firewall, etc. might block access to the conguration pages. Check the help les included with your rewall software for more information on disabling or conguring it. Frequently Asked Questions (continued)Click to the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings buttonNothing should be checked. Click OKGo to the Advanced tab and click the button to restore these settings to their defaultsClick OK. Go to the desktop and close any open windowsGo to Start>Settings>Control Panel. Double click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. Why can´t I access the web based conguration? (continued)
68Frequently Asked Questions (continued)Step4 Check your IP Address. Your computer must have an IP Address in the same range of the device you are attempting to congure. Most D-Link devices use the 192.168.0.X range. How can I nd my IP Address in Windows 95, 98, or ME? Step 1 Click on Start, then click on Run. Step 2 The Run Dialogue Box will appear. Type winipcfg in the window as shown then click OK. Step 3 The IP Conguration window will appear, displaying your Ethernet Adapter Information.  Select your adapter from the drop down menu. If you do not see your adapter in the drop down menu, your adapter is not properly installed. Step 4 After selecting your adapter, it will display your IP Address, subnet mask, and default gateway. Step 5 Click OK to close the IP Conguration windowWhy can´t I access the web based conguration? (continued)
69Frequently Asked Questions (continued)Step4 (continued) Check your IP Address. Your computer must have an IP Address in the same range of the device you are attempting to congure. Most D-Link devices use the 192.168.0.X range. How can I nd my IP Address in Windows 2000/XP? Step 1 Click on Start and select Run. Step 2 Type cmd then click OK. Step 3 From the Command Prompt, enter ipcong. It will return your IP Address, subnet mask, and default gatewayStep 4 Type exit to close the command prompt. Why can´t I access the web based conguration? (continued)
70Frequently Asked Questions (continued)Step4 (continued) Check your IP Address. Your computer must have an IP Address in the same range of the device you are attempting to congure. Most D-Link devices use the 192.168.0.X range. Make sure you take note of your computer´s Default Gateway IP Address. The Default Gateway is the IP Address of the D-Link router. By default, it should be 192.168.0.1. How can I assign a Static IP Address in Windows XP? Step 1 Click on Start > Control Panel > Network and Internet Connections > Network connections. Step 2 See Step 2 for Windows 2000 and continue from there.How can I assign a Static IP Address in Windows 2000? Step 1 Right-click on My Network Places and select Properties. Step 2 Right-click on the Local Area Connection which represents your network card and select Properties. Highlight Internet Protocol (TCP/IP) and click Properties.Why can´t I access the web based conguration? (continued)
71Frequently Asked Questions (continued)How can I assign a Static IP Address in Windows 2000? (continued) Click Use the following IP Address and enter an IP Address that is on the same subnet as the LAN IP Address on your router. Example: If the router´s LAN IP Address is 192.168.0.1, make your IP Address 192.168.0.X where X = 2-99. Make sure that the number you choose is not in use on the network. Set the Default Gateway to be the same as the LAN IP Address of your router (192.168.0.1). Set the Primary DNS to be the same as the LAN IP address of your router (192.168.0.1). The Secondary DNS is not needed or enter a DNS server from your ISP. Click OK twice. You may be asked if you want to reboot your computer. Click Yes. How can I assign a Static IP Address in Windows 98/Me? Step 1 From the desktop, right-click on the Network Neigborhood icon (Win ME - My Network Places) and select Properties Highlight TCP/IP and click the Properties button. If you have more than 1 adapter, then there will be a TCP/IP “Binding” for each adapter. Highlight TCP/IP > (your network adapter) and then click Properties. Why can´t I access the web based conguration? (continued)
72Frequently Asked Questions (continued)How can I assign a Static IP Address in Windows 98/Me? (continued)Step 2 Click Specify an IP Address. Step 3 Click on the Gateway tab. Enter the LAN IP Address of your router here (192.168.0.1).Click Add when nished. Step 4 Click on the DNS Conguration tab. Enter in an IP Address that is on the same subnet as the LAN IP Address on your router. Example: If the router´s LAN IP Address is 192.168.0.1, make your IP Address 192.168.0.X where X is between 2-99. Make sure that the number you choose is not in use on the network. Step 5 Click OK twice. Click Enable DNS. Type in a Host (can be any word). Under DNS server search order, enter the LAN IP Address of your router (192.168.0.1). Click Add. When prompted to reboot your computer, click Yes. After you reboot, the computer will now have a static, private IP Address. Why can´t I access the web based conguration? (continued)Step5Access the web management. Open your web browser and enter the IP Address of your D-Link device in the address bar. This should open the login page for the web management. Follow instructions to login and complete the conguration.
73Frequently Asked Questions (continued)How can I setup my router to work with a Cable modem connection?Dynamic Cable connection (IE AT&T-BI, Cox, Adelphia, Rogers, Roadrunner, Charter, and Comcast). Note: Please congure the router with the computer that was last connected directly to the cable modem. Step1 Log into the web based conguration by typing in the IP Address of the router (default:192.168.0.1) in your web browser. The username is admin (all lowercase) and the password is blank (nothing). Step2Click the Home tab and click the WAN button. Dynamic IP Address is the default value, however, if Dynamic IP Address is not selected as the WAN type, select Dynamic IP Address by clicking on the radio button. Click Clone Mac Address. Click on Apply and then Continue to save the changes.
74Frequently Asked Questions (continued)How can I setup my router to work with a Cable modem connection? (continued)Step3Power cycle the cable modem and router: Turn the cable modem off (rst) . Turn the router off Leave them off for 2 minutes.** Turn the cable modem on (rst). Wait until you get a solid cable light on the cable modem. Turn the router on. Wait 30 seconds. ** If you have a Motorola (Surf Board) modem, leave off for at least 5 minutes. Step4Follow step 1 again and log back into the web conguration. Click the Status tab and click the Device Info button. If you do not already have a public IP Address under the WAN heading, click on the DHCP Renew and Continue buttons. Static Cable ConnectionStep1Log into the web based conguration by typing in the IP Address of the router (default:192.168.0.1) in your web browser. The username is admin (all lowercase) and the password is blank (nothing). Step2Click the Home tab and click the WAN button. Select Static IP Address and enter your static settings obtained from the ISP in the elds provided. If you do not know your settings, you must contact your ISP. Step3 Click on Apply and then click Continue to save the changes. Step4 Click the Status tab and click the Device Info button. Your IP Address information will be displayed under the WAN heading.
75Frequently Asked Questions (continued)How can I setup my router to work with Earthlink DSL or any PPPoE connection? Make sure you disable or uninstall any PPPoE software such as WinPoet or Enternet 300 from your computer or you will not be able to connect to the Internet. Step1Upgrade Firmware if needed. (Please visit the D-Link tech support website at: http://support.dlink.com for the latest rmware upgrade information.) Step2 Take a paperclip and perform a hard reset. With the unit on, use a paperclip and hold down the reset button on the back of the unit for 10 seconds. Release it and the router will recycle, the lights will blink, and then stabilize. Step3 After the router stabilizes, open your browser and enter 192.168.0.1 into the address window and hit the Enter key. When the password dialog box appears, enter the username admin and leave the password blank. Click OK. If the password dialog box does not come up repeat Step 2. Note: Do not run Wizard. Step4 Click on the WAN tab on left-hand side of the screen. Select PPPoE. Step5Select Dynamic PPPoE (unless your ISP supplied you with a static IP Address). Step6In the username eld enter ELN/username@earthlink.net and your password, where username is your own username. For SBC Global users, enter username@sbcglobal.net.For Ameritech users, enter username@ameritech.net.For BellSouth users, enter username@bellsouth.net.For Mindspring users, enter username@mindspring.com.For most other ISPs, enter username. Step7 Maximum Idle Time should be set to zero. Set MTU to 1492, unless specied by your ISP, and set Autoreconnect to Enabled. Note: If you experience problems accessing certain websites and/or email issues, please set the MTU to a lower number such as 1472, 1452, etc. Contact your ISP for more information and the proper MTU setting for your connection.
76 Step8 Click Apply. When prompted, click Continue. Once the screen refreshes, unplug the power to the D-Link router. Step9Turn off your DSL modem for 2-3 minutes. Turn back on. Once the modem has established a link to your ISP, plug the power back into the D-Link router. Wait about 30 seconds and log back into the router. Step10Click on the Status tab in the web conguration where you can view the device info. Under WAN, click Connect. Click Continue when prompted. You should now see that the device info will show an IP Address, verifying that the device has connected to a server and has been assigned an IP Address. How can I setup my router to work with Earthlink DSL or any PPPoE connection? (continued)Frequently Asked Questions (continued)Can I use my D-Link Broadband Router to share my Internet connection provided by AOL DSL Plus?In most cases yes. AOL DSL+ may use PPPoE for authentication bypassing the client software. If this is the case, then our routers will work with this service. Please contact AOL if you are not sure. To set up your router: Step1Log into the web-based conguration (192.168.0.1) and congure the WAN side to use PPPoE. Step2 Enter your screen name followed by @aol.com for the user name. Enter your AOL password in the password box. Step3You will have to set the MTU to 1400. AOL DSL does not allow for anything higher than 1400. Step4 Apply settings. Step5 Recycle the power to the modem for 1 minute and then recycle power to the router. Allow 1 to 2 minutes to connect. If you connect to the Internet with a different internet service provider and want to use the AOL software, you can do that without conguring the router’s rewall settings. You need to congure the AOL software to connect using TCP/IP. Go to http://www.aol.com for more specic conguration information of their software.
77Frequently Asked Questions (continued)How do I open ports on my router?To allow trafc from the internet to enter your local network, you will need to open up ports or the router will block the request. Step1 Open your web browser and enter the IP Address of your D-Link router (192.168.0.1). Enter username (admin) and your password (blank by default). Step2Click on Advanced on top and then click Virtual Server on the left side. Step3Check Enabled to activate entry. Step4 Enter a name for your virtual server entry. Step5 Next to Private IP, enter the IP Address of the computer on your local network that you want to allow the incoming service to. Step6 Choose Protocol Type - either TCP, UDP, or both. If you are not sure, select both. Step7Enter the port information next to Private Port and Public Port. The private and public ports are usually the same. The public port is the port seen from the WAN side, and the private port is the port being used by the application on the computer within your local network. Step8Enter the Schedule information. Step9Click Apply and then click Continue. Note: Make sure DMZ host is disabled. If DMZ is enabled, it will disable all Virtual Server entries. Because our routers use NAT (Network Address Translation), you can only open a specic port to one computer at a time. For example: If you have 2 web servers on your network, you cannot open port 80 to both computers. You will need to congure 1 of the web servers to use port 81. Now you can open port 80 to the rst computer and then open port 81 to the other computer.
78Frequently Asked Questions (continued)What is DMZ?Demilitarized Zone: In computer networks, a DMZ (demilitarized zone) is a computer host or small network inserted as a neutral zone between a company´s private network and the outside public network. It prevents outside users from getting direct access to a server that has company data. (The term comes from the geographic buffer zone that was set up between North Korea and South Korea following the UN police action in the early 1950s.) A DMZ is an optional and more secure approach to a rewall and effectively acts as a proxy server as well. In a typical DMZ conguration for a small company, a separate computer (or host in network terms) receives requests from users within the private network for access to Web sites or other companies accessible on the public network. The DMZ host then initiates sessions for these requests on the public network. However, the DMZ host is not able to initiate a session back into the private network. It can only forward packets that have already been requested. Users of the public network outside the company can access only the DMZ host. The DMZ may typically also have the company´s Web pages so these could be served to the outside world. However, the DMZ provides access to no other company data. In the event that an outside user penetrated the DMZ hosts security, the Web pages might be corrupted but no other company information would be exposed. D-Link, a leading maker of routers, is one company that sells products designed for setting up a DMZHow do I congure the DMZ Host?The DMZ feature allows you to forward all incoming ports to one computer on the local network. The DMZ, or Demilitarized Zone, will allow the specied computer to be exposed to the Internet. DMZ is useful when a certain application or game does not work through the rewall. The computer that is congured for DMZ will be completely vulnerable on the Internet, so it is suggested that you try opening ports from the Virtual Server or Firewall settings before using DMZ. Step1 Find the IP address of the computer you want to use as the DMZ host. To nd out how to locate the IP Address of the computer in Windows XP/2000/ME/9x or Macintosh operating systems please refer to Step 4 of the rst question in this section (Frequently Asked Questions).
79Frequently Asked Questions (continued)Step2Log into the web based conguration of the router by typing in the IP Address of the router (default:192.168.0.1) in your web browser. The username is admin (all lowercase) and the password is blank (nothing) How do I congure the DMZ Host? (continued)Step3Click the Advanced tab and then click on the DMZ button. Select Enable and type in the IP Address you found in step 1. Step4Click Apply and then Continue to save the changes. Note: When DMZ is enabled, Virtual Server settings will still be effective. Remember, you cannot forward the same port to multiple IP Addresses, so the Virtual Server settings will take priority over DMZ settings.
80Frequently Asked Questions (continued)How do I open a range of ports on my DI-524 using Firewall rules?Step1Access the router’s web conguration by entering the router’s IP Address in your web browser. The default IP Address is 192.168.0.1. Login using your password. The default username is “admin” and the password is blank. If you are having difculty accessing web management, please see the rst question in this section.Step2From the web management Home page, click the Advanced tab then click the Firewall button. Step3Click on Enabled and type in a name for the new rule. Step4Choose WAN as the Source and enter a range of IP Addresses out on the internet that you would like this rule applied to. If you would like this rule to allow all internet users to be able to access these ports, then put an Asterisk in the rst box and leave the second box empty. Step5Select LAN as the Destination and enter the IP Address of the computer on your local network that you want to allow the incoming service to. This will not work with a range of IP Addresses. Step6Enter the port or range of ports that are required to be open for the incoming service. Step7Click Apply and then click Continue. Because our routers use NAT (Network Address Translation), you can only open a specic port to one computer at a time. For example: If you have 2 web servers on your network, you cannot open port 80 to both computers. You will need to congure 1 of the web servers to use port 81. Now you can open port 80 to the rst computer and then open port 81 to the other computer. Note: Make sure DMZ host is disabled.
81Frequently Asked Questions (continued)What are virtual servers?A Virtual Server is dened as a service port, and all requests to this port will be redirected to the computer specied by the server IP. For example, if you have an FTP Server (port 21) at 192.168.0.5, a Web server (port 80) at 192.168.0.6, and a VPN server at 192.168.0.7, then you need to specify the following virtual server mapping table: Server Port Server IP Enable 21 192.168.0.5 X80 192.168.0.6 X1723 192.168.0.7 XHow do I use PC Anywhere with my DI-524 router?You will need to open 3 ports in the Virtual Server section of your D-Link router. Step1 Open your web browser and enter the IP Address of the router (192.168.0.1). Step2 Click on Advanced at the top and then click Virtual Server on the left side. Step3 Enter the information as seen below. The Private IP is the IP Address of the computer on your local network that you want to connect to. Step4The rst entry will read as shown here: Step5 Click Apply and then click Continue.
82How do I use PC Anywhere with my DI-524 router? (continued)Frequently Asked Questions (continued)Step6 Create a second entry as shown here: Step7 Click Apply and then click Continue. Step8 Create a third and nal entry as shown here: Step9 Click Apply and then click Continue. Step10Run PCAnywhere from the remote site and use the WAN IP Address of the router, not your computer´s IP Address.
83How can I use eDonkey behind my D-Link Router?Frequently Asked Questions (continued)You must open ports on your router to allow incoming trafc while using eDonkey. eDonkey uses three ports (4 if using CLI): 4661 (TCP) To connect with a server 4662 (TCP) To connect with other clients 4665 (UDP) To communicate with servers other than the one you are connected to. 4663 (TCP) *Used with the command line (CLI) client when it is congured to allow remote connections. This is the case when using a Graphical Interface (such as the Java Interface) with the client. Step1 Open your web browser and enter the IP Address of your router (192.168.0.1). Enter username (admin) and your password (leave blank). Step2 Click on Advanced and then click Firewall. Step3 Create a new rewall rule: Click Enabled. Enter a name (edonkey). Click Allow. Next to Source, select WAN under interface. In the rst box, enter an *. Leave the second box empty. Next to Destination, select LAN under interface. Enter the IP Address of the computer you are running eDonkey from. Leave the second box empty. Under Protocol, select *. In the port range boxes, enter 4661 in the rst box and then 4665 in the second box. Click Always or set a schedule. Step4 Click Apply and then Continue.
84Frequently Asked Questions (continued)To allow you to play SOCOM and hear audio, you must download the latest rmware for the router (if needed), enable Game Mode, and open port 6869 to the IP Address of your Playstation. Step1 Upgrade rmware (follow link above). Step2Open your web browser and enter the IP Address of the router (192.168.0.1). Enter username (admin) and your password (blank by default). Step3 Click on the Advanced tab and then click on Virtual Server on the left side. Step4 You will now create a new Virtual Server entry. Click Enabled and enter a name (socom). Enter the IP Address of your Playstation for Private IP. Step5 For Protocol Type select Both. Enter 6869 for both the Private Port and Public Port. Click Always. Click Apply to save changes and then ContinueStep6 Click on the Tools tab and then Misc on the left side. Step7 Make sure Gaming Mode is Enabled. If not, click Enabled. Click Apply and then Continue. How do I set up my router for SOCOM on my Playstation 2?
85Frequently Asked Questions (continued)How can I use Gamespy behind my D-Link router?Step1 Open your web browser and enter the IP Address of the router (192.168.0.1). Enter admin for the username and your password (blank by default). Step2 Click on the Advanced tab and then click Virtual Server on the left side. Step3 You will create 2 entries. Step4 Click Enabled and enter Settings: Click Apply and then continueStep5 Enter 2nd entry: Click Enabled Click Apply and then continue. NAME - Gamespy1 PRIVATE IP - The IP Address of your computer that you are running Gamespy from. PROTOCOL TYPE - Both PRIVATE PORT - 3783 PUBLIC PORT - 3783 SCHEDULE - Always. NAME - Gamespy2 PRIVATE IP - The IP Address of your computer that you are running Gamespy from. PROTOCOL TYPE - Both PRIVATE PORT - 6500 PUBLIC PORT - 6500 SCHEDULE - Always.
86Frequently Asked Questions (continued)How do I congure my router for KaZaA and Grokster?The following is for KaZaA, Grokster, and others using the FastTrack P2P le sharing system. In most cases, you do not have to congure anything on the router or on the Kazaa software. If you are having problems, please follow steps below: Step1 Enter the IP Address of your router in a web browser (192.168.0.1). Step2 Enter your username (admin) and your password (blank by default). Step3 Click on Advanced and then click Virtual Server. Step4 Click Enabled and then enter a Name (kazaa for example). Step5 Enter the IP Address of the computer you are running KaZaA from in the Private IP box. Select TCP for the Protocol Type. Step6 Enter 1214 in the Private and Public Port boxes. Click Always under schedule or set a time range. Click Apply. Make sure that you did not enable proxy/rewall in the KaZaA software.
87Frequently Asked Questions (continued)How do I congure my router to play Warcraft 3?You must open ports on your router to allow incoming trafc while hosting a game in Warcraft 3. To play a game, you do not have to congure your router. Warcraft 3 (Battlenet) uses port 6112. For the DI-604, DI-614+. DI-524, DI-754, DI-764, or DI-774: Step1 Open your web browser and enter the IP Address of your router (192.168.0.1). Enter username (admin) and your password (leave blank). Step2 Click on Advanced and then click Virtual Server. Step3 Create a new entry: Click Enabled. Enter a name (warcraft3). Private IP - Enter the IP Address of the computer you want to host the game. Select Both for Protocol Type Enter 6112 for both Private Port and Public Port Click Always or set a schedule. Step4 Click Apply and then Continue. Note: If you want multiple computers from you LAN to play in the same game that you are hosting, then repeat the steps above and enter the IP Addresses of the other computers. You will need to change ports. Computer #2 can use port 6113, computer #3 can use 6114, and so on. You will need to change the port information within the Warcraft 3 software for computers #2 and up. Congure the Game Port information on each computer: Start Warcraft 3 on each computer, click Options > Gameplay. Scroll down and you should see Game Port. Enter the port number as you entered in the above steps.
88Frequently Asked Questions (continued)How do I use NetMeeting with my D-Link Router?Unlike most TCP/IP applications, NetMeeting uses DYNAMIC PORTS instead of STATIC PORTS. That means that each NetMeeting connection is somewhat different than the last. For instance, the HTTP web site application uses port 80. NetMeeting can use any of over 60,000 different ports. All broadband routers using (only) standard NAT and all internet sharing programs like Microsoft ICS that use (only) standard NAT will NOT work with NetMeeting or other h.323 software packages. The solution is to put the router in DMZ. Note: A few hardware manufacturers have taken it on themselves to actually provide H.323 compatibility. This is not an easy task since the router must search each incoming packet for signs that it might be a netmeeting packet. This is a whole lot more work than a router normally does and may actually be a weak point in the rewall. D-Link is not one of the manufacturers. To read more on this visit http://www.HomenetHelp.com How do I set up my router to use iChat? -for Macintosh users-You must open ports on your router to allow incoming trafc while using iChat. iChat uses the following ports: 5060 (UDP) 5190 (TCP) File Sharing 16384-16403 (UDP) To video conference with other clients Step1 Open your web browser and enter the IP Address of your router (192.168.0.1). Enter username (admin) and your password (leave blank). Step2 Click on Advanced and then click Firewall.
89Frequently Asked Questions (continued)Step3Create a new rewall rule: Leave the second box empty. Under Protocol, select UDP. In the port range boxes, enter 5060 in the rst box and leave the second box empty. Click Always or set a schedule. Step4 Click Apply and then Continue. Step5Repeat steps 3 and 4 enter ichat2 and open ports 16384-16403 (UDP). How do I set up my router to use iChat? -for Macintosh users- (continued)Click Enabled. Enter a name (ichat1). Click Allow. Next to Source, select WAN under interface.In the rst box, enter an *.Leave the second box empty. Next to Destination, select LAN under interface. Enter the IP Address of the computer you are running iChat from.
90Frequently Asked Questions (continued)If using Mac OS X Firewall, you may need to temporarily turn off the rewall in the Sharing preference pane on both computers. To use the Mac OS X Firewall, you must open the same ports as in the router: Step1 Choose Apple menu > System Preferences. Step2 Choose View > Sharing. Step3 Click the Firewall tab.Step4 Click New. Step5Choose Other from the Port Name pop-up menu.Step6 In the Port Number, Range or Series eld, type in: 5060, 16384-16403. Step7 In the Description eld type in: iChat AV Step8 Click OK. For File Sharing: Step1 Click on Advanced and then Virtual Server. Step2 Check Enabled to activate entry. Step3 Enter a name for your virtual server entry (ichat3). Step4Next to Private IP, enter the IP Address of the computer on your local network that you want to allow the incoming service to. Step5 Select TCP for Protocol Type. Step6 Enter 5190 next to Private Port and Public Port. Stsp7 Click Always or congure a schedule. Step8 Click Apply and then Continue. How do I set up my router to use iChat? -for Macintosh users- (continued)
91Frequently Asked Questions (continued)How do I send or receive a le via iChat when the Mac OSX rewall is active? -for Macintosh users- Mac OS X 10.2 and later“iChat cannot send or receive a le when the Mac OS X rewall is active in its default state. If you have opened the AIM port, you may be able to receive a le but not send them. In its default state, the Mac OS X rewall blocks le transfers using iChat or America Online AIM software. If either the sender or receiver has turned on the Mac OS X re-wall, the transfer may be blocked. The simplest workaround is to temporarily turn off the rewall in the Sharing preference pane on both computers. This is required for the sender. However, the receiver may keep the rewall on if the AIM port is open. To open the AIM port:If you do not want to turn off the rewall at the sending computer, a different le sharing service may be used instead of iChat. The types of le sharing available in Mac OS X are outlined in technical document 106461, “Mac OS X: File Sharing” in the AppleCare Knowledge base online.Note: If you use a le sharing service when the rewall is turned on, be sure to click the Firewall tab and select the service you have chosen in the “Allow” list. If you do not do this, the rewall will also block the le sharing service. “The following information is from the online Macintosh AppleCare knowledge base:Step1Choose Apple menu > System Preferences.Step2 Choose View > Sharing.Step3 Click the Firewall tab.Step4 Click New.Step5 Choose AOL IM from the Port Name pop-up menu. The number 5190 should already be lled in for you.Step6 Click OK.
92What is NAT?NAT stands for Network Address Translator. It is proposed and described in RFC-1631 and is used for solving the IP Address depletion problem. Basically, each NAT box has a table consisting of pairs of local IP Addresses and globally unique addresses, by which the box can “translate” the local IP Addresses to global address and vice versa. Simply put, it is a method of connecting multiple computers to the Internet (or any other IP network) using one IP Address. D-Link´s broadband routers (ie: DI-604) support NAT. With proper conguration, multiple users can access the Internet using a single account via the NAT device. For more information on RFC-1631: The IP Network Address Translator (NAT), visit http://www.faqs.org/rfcs/rfc1631.html Frequently Asked Questions (continued)
FCC Statement: Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Navigation menu