D Link SR250NA1 Wireless N Service Router User Manual 2 of 2

D Link Corporation Wireless N Service Router 2 of 2

1. User manual 1 of 2
2. User manual 2 of 2

User manual 2 of 2

Download:
Mirror Download [FCC.gov]
Document ID	1490224
Application ID	Fcxs9L26PsTq+aqXQCNiyg==
Document Description	User manual 2 of 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	174.7kB (2183760 bits)
Date Submitted	2011-06-26 00:00:00
Date Available	2011-06-26 00:00:00
Creation Date	2011-06-20 15:00:53
Producing Software	MicrosoftÂ® Word 2010
Document Lastmod	2011-06-24 15:54:45
Document Title	User manual 2 of 2
Document Creator	MicrosoftÂ® Word 2010

Unified Services Router
User Manual
Symptom: Router can obtain an IP address, but PC is unable to load Internet pages.
Recommended action:
1. Ask your ISP for the addresses of its designated Domain Name System (DNS) servers.
Configure your PC to recognize those addresses. For details, see your operating system
documentation.
2. On your PC, configure the router to be its TCP/IP gateway.
11.2 Date and time
Symptom: Date shown is January 1, 1970.
Possible cause: The router has not yet successfully reached a network t ime server
(NTS).
Recommended action:
1. If you have just configured the router, wait at least 5 minutes, select Administration >
Time Zone , and recheck the date and time.
2. Verify your Internet access settings.
Symptom: Time is off by one hour.
Possible cause: The router does not automatically adjust for Daylight Savings Time.
Recommended action:
1. Select Administration > Time Zone and view the current date and time settings.
2. Click to check or uncheck ―Automatically adjust for Daylight Savings Time‖, then click
Apply.
11.3 Pinging to Test LAN Connectivity
Most TCP/IP terminal devices and firewalls contain a ping utility that sends an ICMP
echo-request packet to the designated device. The DSR responds with an echo reply.
Troubleshooting a TCP/IP network is made very ea sy by using the ping utility in your
PC or workstation.
11.3.1 Testing the LAN path from your PC to your
router
1. From the PC‘s Windows toolbar, select Start > Run.
2. Type ping  where  is the router‘s IP address. Example: ping
192.168.10.1.
3. Click OK.
149
Unified Services Router
User Manual
4. Observe the display:

If the path is working, you see this message sequence:
Pinging  with 32 bytes of data
Reply from : bytes=32 time=NN ms TTL=xxx

If the path is not working, you see this message sequence:
Pinging  with 32 bytes of data
Request timed out
5. If the path is not working, Test the physical connections between PC and router

If the LAN port LED is off, go to the ―LED displays‖ section on page B1 and follow instructions for ―LAN or Internet port LEDs are not lit.‖

Verify that the corresponding link LEDs are lit for your network
interface card and for any hub ports that are connected to your
workstation and firewall.
6. If the path is still not up, test the network configuration:

Verify that the Ethernet card driver software and TCP/IP software are
installed and configured on the PC.

Verify that the IP address for the router and PC are correct and on the
same subnet.
11.3.2 Testing the LAN path from your PC to a remote
device
1. From the PC‘s Windows toolbar, select Start > Run.
2. Type ping -n 10  where -n 10 specifies a maximum of 10 tries and  is the IP address of a remote device such as your ISP‘s DNS server. Example:
ping -n 10 10.1.1.1.
3. Click OK and then observe the display (see the previous procedure).
4. If the path is not working, do the following:

Check that the PC has the IP address of your firewall listed as the
default gateway. (If the IP configuration of your PC is assigned by
DHCP, this information is not visible in your PC‘s Network C ontrol
Panel.)
150
Unified Services Router

User Manual
Verify that the network (subnet) address of your PC is different from the
network address of the remote device.

Verify that the cable or DSL modem is connected and functioning.

Ask your ISP if it assigned a hostname to your PC.
If yes, select Network Configuration > WAN Settings > Ethernet ISP
Settings and enter that hostname as the ISP account name.

Ask your ISP if it rejects the Ethernet MAC addresses of all but one of
your PCs.
Many broadband ISPs restrict access by allowing traffic from t he MAC address of
only your broadband modem; but some ISPs additionally restrict access to the MAC
address of just a single PC connected to that modem. If this is the case, configure
your firewall to clone or spoof the MAC address from the authorized PC.
11.4 Restoring factory-default configuration
settings
To restore factory-default configuration settings, do either of the following:
1. Do you know the account password and IP address?

If yes, select Administration > Settings Backup & Upgrade and
click default.

If no, do the following:
On the rear panel of the router, press and hold the Reset button about 10 seconds,
until the test LED lights and then blinks.
Release the button and wait for the router to reboot.
2. If the router does not restart automatically; manually restart it to make the default settings
effective.
3. After a restore to factory defaults —whether initiated from the configuration interface or
the Reset button — the following settings apply:

LAN IP address: 192.168.10.1

Username: admin

Password: password

DHCP server on LAN: enabled

WAN port configuration: Get configuration via DHCP
151
Chapter 12. Credits
Microsoft, Windows are registered trademarks of Microsoft Corp.
Linux is a registered trademark of Linus Torvalds.
UNIX is a registered trademark of The Open Group.
Unified Services Router
User Manual
Appendix A. Glossary
ARP
Address Resolution Protocol. Broadcast protocol for mapping IP addresses to MAC addresses.
CHAP
Challenge-Handshake Authentication Protocol. Protocol for authenticating users to an ISP.
DDNS
Dynamic DNS. System for updating domain names in real time. Allows a domain name to be
assigned to a device with a dynamic IP address.
DHCP
Dynamic Host Configuration Protocol. Protocol for allocating IP addresses dynamically so that
addresses can be reused when hosts no longer need them.
DNS
Domain Name System. Mechanism for translating H.323 IDs, URLs, or e-mail IDs into IP
addresses. Also used to assist in locating remote gatekeepers and to map IP addresses to
hostnames of administrative domains.
FQDN
Fully qualified domain name. Complete domain name, including the host portion. Example:
serverA.companyA.com.
FTP
File Transfer Protocol. Protocol for transferring files between network nodes.
HTTP
Hypertext Transfer Protocol. Protocol used by web browsers and web servers to transfer files.
IKE
Internet Key Exchange. Mode for securely exchanging encryption keys in ISAKMP as part of
building a VPN tunnel.
IPsec
IP security. Suite of protocols for securing VPN tunnels by authenticating or encrypting IP
packets in a data stream. IPsec operates in either transport mode (encrypts payload but not
packet headers) or tunnel mode (encrypts both payload and packet headers).
ISAKMP
Internet Key Exchange Security Protocol. Protocol for establishing security associations and
cryptographic keys on the Internet.
ISP
Internet service provider.
MAC Address
Media-access-control address. Unique physical-address identifier attached to a network
adapter.
MTU
Maximum transmission unit. Size, in bytes, of the largest packet that can be passed on. The
MTU for Ethernet is a 1500-byte packet.
NAT
Network Address Translation. Process of rewriting IP addresses as a packet passes through a
router or firewall. NAT enables multiple hosts on a LAN to access the Internet using the single
public IP address of the LAN’s gateway router.
NetBIOS
Microsoft Windows protocol for file sharing, printer sharing, messaging, authentication, and
name resolution.
NTP
Network Time Protocol. Protocol for synchronizing a router to a single clock on the network,
known as the clock master.
PAP
Password Authentication Protocol. Protocol for authenticating users to a remote access server
or ISP.
154
Unified Services Router
User Manual
PPPoE
Point-to-Point Protocol over Ethernet. Protocol for connecting a network of hosts to an ISP
without the ISP having to manage the allocation of IP addresses.
PPTP
Point-to-Point Tunneling Protocol. Protocol for creation of VPNs for the secure transfer of data
from remote clients to private servers over the Internet.
RADIUS
Remote Authentication Dial-In User Service. Protocol for remote user authentication and
accounting. Provides centralized management of usernames and passwords.
RSA
Rivest-Shamir-Adleman. Public key encryption algorithm.
TCP
Transmission Control Protocol. Protocol for transmitting data over the Internet with guaranteed
reliability and in-order delivery.
UDP
User Data Protocol. Protocol for transmitting data over the Internet quickly but with no
guarantee of reliability or in-order delivery.
VPN
Virtual private network. Network that enables IP traffic to travel securely over a public TCP/IP
network by encrypting all traffic from one network to another. Uses tunneling to encrypt all
information at the IP level.
WINS
Windows Internet Name Service. Service for name resolution. Allows clients on different IP
subnets to dynamically resolve addresses, register themselves, and browse the network without
sending broadcasts.
XAUTH
IKE Extended Authentication. Method, based on the IKE protocol, for authenticating not just
devices (which IKE authenticates) but also users. User authentication is performed after device
authentication and before IPsec negotiation.
155
Appendix B. Factory Default Settings
Feature
Device login
Internet
Connection
Description
Default Setting
User login URL
http://192.168.10.1
User name (case sensitive)
admin
Login password (case sensitive)
admin
WAN MAC address
Use default address
WAN MTU size
1500
Port speed
Autosense
IP address
192.168.10.1
IPv4 subnet mask
255.255.255.0
RIP direction
None
RIP version
Disabled
RIP authentication
Disabled
DHCP server
Enabled
DHCP starting IP address
192.168.10.2
DHCP ending IP address
192.168.10.100
Time zone
GMT
Time zone adjusted for Daylight Saving Time
Disabled
SNMP
Disabled
Remote management
Disabled
Inbound communications from the Internet
Disabled (except traffic on port
80, the HTTP port)
Outbound communications to the Internet
Enabled (all)
Source MAC filtering
Disabled
Stealth mode
Enabled
Local area network
(LAN)
Firewall
Unified Services Router
User Manual
Appendix C. Standard Services
Available for Port Forwarding
& Firewall Configuration
ANY
ICMP-TYPE-8
RLOGIN
AIM
ICMP-TYPE-9
RTELNET
BGP
ICMP-TYPE-10
RTSP:TCP
BOOTP_CLIENT
ICMP-TYPE-11
RTSP:UDP
BOOTP_SERVER
ICMP-TYPE-13
SFTP
CU-SEEME:UDP
ICQ
SMTP
CU-SEEME:TCP
IMAP2
SNMP:TCP
DNS:UDP
IMAP3
SNMP:UDP
DNS:TCP
IRC
SNMP-TRAPS:TCP
FINGER
NEWS
SNMP-TRAPS:UDP
FTP
NFS
SQL-NET
HTTP
NNTP
SSH:TCP
HTTPS
PING
SSH:UDP
ICMP-TYPE-3
POP3
STRMWORKS
ICMP-TYPE-4
PPTP
TACACS
ICMP-TYPE-5
RCMD
TELNET
ICMP-TYPE-6
REAL-AUDIO
TFTP
ICMP-TYPE-7
REXEC
VDOLIVE
158
Unified Services Router
User Manual
Appendix D. Log Output Reference
Facility: System (Networking)
Log Message
DBUpdate event: Table: %s opCode:%d
rowId:%d
Severity
Severity
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Log Message
BridgeConfig: too few arguments to
command %s
BridgeConfig: too few arguments to
command %s
sqlite3QueryResGet failed.Query:%s
ddnsDisable failed
sqlite3QueryResGet failed.Query:%s
sqlite3QueryResGet failed.Query:%s
ddnsDisable failed
failed to call ddns enable
ddnsDisable failed
networkIntable.txt not found
sqlite3QueryResGet failed
Interface is already deleted in bridge
removing %s from bridge %s... %s
adding %s to bridge %s... %s
stopping bridge...
stopping bridge...
stopping bridge...
%s:DBUpdate event: Table: %s
opCode:%d rowId:%d
Wan is not up
%s:DBUpdate event: Table: %s
opCode:%d rowId:%d
doDNS:failed
doDNS:failed
doDNS:Result = FAILED
doDNS:Result SUCCESS
Write Old Entry: %s %s %s: to %s
Write New Entry: %s %s #%s : to %s
Write Old Entry: %s %s %s: to %s
Write New Entry: %s %s #%s : to %s
ifStaticMgmtDBUpdateHandler: returning
with "
nimfLinkStatusGet: buffer: \
nimfLinkStatusGetErr: returning with
status: %d
nimfAdvOptSetWrap: current Mac
Option: %d
nimfAdvOptSetWrap: current Port Speed
Option: %d
nimfAdvOptSetWrap: current Mtu Option:
%d
nimfAdvOptSetWrap: looks like we are
reconnecting. "
nimfAdvOptSetWrap: Mtu Size: %d
nimfAdvOptSetWrap: NIMF table is %s
nimfAdvOptSetWrap:WAN_MODE
TRIGGER
nimfAdvOptSetWrap: MTU: %d
nimfAdvOptSetWrap: MacAddress: %s
nimfAdvOptSetWrap: old Mtu Flag: %d
DEBUG
DEBUG
sqlite3QueryResGet failed.Query:%s
Error in executing DB update handler
ERROR
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
sqlite3QueryResGet failed.Query:%s
Illegal invocation of ddnsView (%s)
sqlite3QueryResGet failed.Query:%s
sqlite3QueryResGet failed.Query:%s
ddns: SQL error: %s
Illegal operation interface got deleted
sqlite3QueryResGet failed.Query:%s
sqlite3QueryResGet failed.Query:%s
sqlite3QueryResGet failed.Query:%s
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
DEBUG
DEBUG
ddnsDisable failed
ddns: SQL error: %s
ERROR
ERROR
DEBUG
Failed to call ddns enable
ERROR
DEBUG
ddns: SQL error: %s
ERROR
DEBUG
sqlite3QueryResGet failed.Query:%s
ERROR
DEBUG
Failed to call ddns enable
ERROR
DEBUG
DEBUG
DEBUG
ddns: SQL error: %s
ddnsDisable failed
ddns: SQL error: %s
ERROR
ERROR
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
sqlite3QueryResGet failed.Query:%s
Failed to call ddns enable
ddns: SQL error: %s
ddnsDisable failed
ERROR
ERROR
ERROR
ERROR
DEBUG
159
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
nimfAdvOptSetWrap: user has changed
MTU option
nimfAdvOptSetWrap: MTU: %d
nimfAdvOptSetWrap: old MTU size: %d
nimfAdvOptSetWrap: old Port Speed
Option: %d
nimfAdvOptSetWrap: old Mac Address
Option: %d
nimfAdvOptSetWrap: MacAddress: %s
Setting LED [%d]:[%d] For %s
l2tpEnable: command string: %s
nimfAdvOptSetWrap: handling reboot
scenario
nimfAdvOptSetWrap: INDICATOR = %d
nimfAdvOptSetWrap: UpdateFlag: %d
nimfAdvOptSetWrap: returning with
status: %s
nimfGetUpdateMacFlag: MacTable Flag
is: %d
User Manual
DEBUG
DEBUG
DEBUG
ddns: SQL error: %s
sqlite3QueryResGet failed.Query:%s
sqlite3QueryResGet failed.Query:%s
ERROR
ERROR
ERROR
DEBUG
ddnsDisable failed
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
ddns: SQL error: %s
sqlite3QueryResGet failed.Query:%s
sqlite3QueryResGet failed.Query:%s
ddnsDisable failed
ERROR
ERROR
ERROR
ERROR
DEBUG
DEBUG
DEBUG
failed to call ddns enable
ddns: SQL error: %s
ddnsDisable failed
ERROR
ERROR
ERROR
DEBUG
sqlite3QueryResGet failed.Query:%s
ERROR
DEBUG
ERROR
nimfMacGet: Mac Option changed
DEBUG
nimfMacGet: Update Flag: %d
nimfMacGet: MacAddress: %s
nimfMacGet: MacAddress: %s
nimfMacGet: MacAddress: %s
nimfMacGet: MacAddress: %s
nimfMacGet: MacAddress: %s
nimfMacGet:Mac option Not changed \
nimfMacGet: MacAddress: %s
nimfMacGet: MacAddress: %s
nimfMacGet: MacAddress: %s
nimfMacGet: returning with status: %s
Now in enableing LanBridge function
sucessfully executed the command %s
Now in disableing LanBridge function
sucessfully executed the command %s
configPortTblHandler:Now we are in
Sqlite Update "
The Old Configuration of ConfiPort
was:%s
The New Configuration of ConfiPort
was:%s
The user has deselected the
configurable port
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Error in executing DB update handler
Failed to open the resolv.conf file.
Exiting./n
Could not write to the resolv.conf file.
Exiting.
Error opening the lanUptime File
Error Opening the lanUptime File.
failed to open %s
failed to open %s
failed to query networkInterface table
failed to query networkInterface table
sqlite3QueryResGet failed.Query:%s
failed to enable IPv6 forwarding
failed to set capabilities on the "
failed to enable IPv6 forwarding
failed to set capabilities on the "
failed to disable IPv6 forwarding
failed to set capabilities on the "
failed to open %s
DEBUG
Could not create ISATAP Tunnel
ERROR
DEBUG
Could not destroy ISATAP Tunnel
ERROR
DEBUG
ERROR
failed query %s
DEBUG
failed query %s
DEBUG
failed query %s
%s:DBUpdate event: Table: %s
opCode:%d rowId:%d
DEBUG
Could not configure ISATAP Tunnel
Could not de-configure ISATAP
Tunnel
nimfStatusUpdate: updating
NimfStatus failed
nimfStatusUpdate: updating
NimfStatus failed
nimfLinkStatusGet: determinig link's
status failed
nimfLinkStatusGet: opening status file
failed
DEBUG
DEBUG
160
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
%s:DBUpdate event: Table: %s
opCode:%d rowId:%d
%s:%d SIP ENABLE: %s
sipTblHandler:failed to update ifStatic
sipTblHandler:failed to update Configport
DEBUG
DEBUG
DEBUG
DEBUG
%s:%d SIP DISABLE: %s
DEBUG
%s:%d SIP SET CONF: %s
DEBUG
Failed to open %s: %s
Failed to start sipalg
DEBUG
DEBUG
Failed to stop sipalg
DEBUG
Failed to get config info
DEBUG
Network Mask: 0x%x
DEBUG
RTP DSCP Value: 0x%x
DEBUG
Need more arguments
DEBUG
Invalid lanaddr
DEBUG
Invalid lanmask
DEBUG
Invalid option
DEBUG
Failed to set config info
DEBUG
Unknown option
DEBUG
sshdTblHandler
DEBUG
pPort: %s
DEBUG
pProtocol: %s
DEBUG
pListerAddr: %s
DEBUG
pKeyBits: %s
DEBUG
pRootEnable: %s
DEBUG
pRsaEnable: %s
DEBUG
pDsaEnable: %s
DEBUG
pPassEnable: %s
DEBUG
pEmptyPassEnable: %s
DEBUG
pSftpEnable: %s
DEBUG
pScpEnable: %s
DEBUG
pSshdEnable: %s
DEBUG
Failed to commit
ifStatusDBUpdate: Failed to begin "
%s: SQL error: %s
%s: Failed to commit "
nimfNetIfaceTblHandler: unable to get
LedPinId
nimfNetIfaceTblHandler: unable to get
LedPinId
nimfNetIfaceTblHandler: unable to get
LedPinId
%s: unable to kill dhclient
nimfAdvOptSetWrap: unable to get
current Mac Option
nimfAdvOptSetWrap: unable to get
current Port "
nimfAdvOptSetWrap: unable to get
current MTU Option
nimfAdvOptSetWrap: error getting
Mac Address from "
nimfAdvOptSetWrap: unable to get
the MTU
nimfAdvOptSetWrap: error setting
interface advanced "
nimfAdvOptSetWrap: error getting
MTU size
nimfAdvOptSetWrap: unable to get
Mac Address
nimfAdvOptSetWrap: error setting
interface advanced "
nimfAdvOptSetWrap: failed to get old
connectiontype
nimfAdvOptSetWrap: old connection
type is: %s
nimfAdvOptSetWrap: failed to get old
MTU Option
nimfAdvOptSetWrap: error getting
MTU size
nimfOldFieldValueGet: failed to get
old "
nimfOldFieldValueGet: user has
changed MTU size
nimfAdvOptSetWrap: failed to get old
Port Speed "
nimfAdvOptSetWrap: user has
changed Port Speed
nimfAdvOptSetWrap: failed to get old
Mac Address "
nimfAdvOptSetWrap: user has
changed Mac Address "
nimfAdvOptSetWrap: unable to get
Mac Address
nimfAdvOptSetWrap:Failed to RESET
the flag
nimfAdvOptSetWrap: setting
advanced options failed
nimfAdvOptSetWrap: interface
advanced options applied
161
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
pPrivSep: %s
%s:DBUpdate event: Table: %s
opCode:%d rowId:%d
Re-Starting sshd daemon....
sshd re-started successfully.
sshd stopped .
failed query %s
vlan disabled, not applying vlan
configuration..
failed query %s
failed query %s
DEBUG
no ports present in this vlanId %d
failed query %s
vlan disabled, not applying vlan
configuration..
disabling vlan
enabling vlan
vlan disabled, not applying vlan
configuration..
DEBUG
DEBUG
no ports present in this vlanId %d
DEBUG
failed query %s
vlan disabled, not applying vlan
configuration..
DEBUG
removing %s from bridge%s... %s
DEBUG
adding %s to bridge%d... %s
restarting bridge...
[switchConfig] Ignoring event on port
number %d
restarting bridge...
DEBUG
DEBUG
executing %s ... %s
DEBUG
removing %s from bridge%s... %s
adding %s to bridge%d... %s
DEBUG
DEBUG
[switchConfig] Ignoring event on %s
restarting bridge...
[switchConfig] Ignoring event on port
number %d
[switchConfig] executing %s ... %s
restarting bridge...
UserName: %s
Password: %s
IspName: %s
DEBUG
DEBUG
DialNumber: %s
DEBUG
Apn: %s
DEBUG
nimfGetUpdateMacFlag: unable to get
Flag from MacTable
nimfMacGet: Updating MAC address
failed
sqlite3QueryResGet failed.Query:%s
error executing the command %s
error executing the command %s
error executing the command %s
disableLan function is failed to disable
ConfigPort"
sqlite3QueryResGet failed.Query:%s
sqlite3QueryResGet failed.Query:%s
Unable to Disable configurable port
from
configPortTblHandler has failed
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
162
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
sqlite3QueryResGet failed.Query:%s
Error in executing DB update handler
sqlite3QueryResGet failed
Failed to execute switchConfig for
port\
Failed to execute switchConfig for
port enable
Failed to execute ifconfig for port
enable
ERROR
ERROR
ERROR
Failed to execute ethtool for\
Failed to execute switchConfig for
port disable
Failed to execute ifconfig for port
disable
sqlite3QueryResGet failed
ERROR
sqlite3_mprintf failed
sqlite3QueryResGet failed
Failed to execute switchConfig for
port mirroring
Usage:%s    
sqlite3QueryResGet failed
Could not get all the required
variables to email the Logs.
runSmtpClient failed
ERROR
ERROR
getaddrinfo returned %s
file not found
sqlite3QueryResGet failed.Query:%s
sqlite3QueryResGet failed.Query:%s
sqlite3QueryResGet failed.Query:%s
No memory to allocate
Failed to Open SSHD Configuration
File
Ipaddress should be provided with
accessoption 1
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
GetDnsFromIsp: %s
IdleTimeOutFlag: %s
IdleTimeOutValue: %d
AuthMetho: %d
executing %s ... %s
removing %s from bridge%d... %s
adding %s to bridge%d... %s
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
stopping bridge...
restarting bridge...
Could not configure 6to4 Tunnel
Interface
Could not de-configure 6to4 Tunnel
Interface
failed to restart 6to4 tunnel interfaces
BridgeConfig: too few arguments to
command %s
BridgeConfig: unsupported command %d
DEBUG
DEBUG
BridgeConfig returned error=%d
sqlite3QueryResGet failed
Error in executing DB update handler
DEBUG
DEBUG
DEBUG
sqlite3QueryResGet failed
Failed to remove vlan Interface for vlanId
DEBUG
sqlite3QueryResGet failed
DEBUG
Invalid oidp passed
Invalid oidp passed
Failed to get oid from the tree
DEBUG
DEBUG
DEBUG
threegEnable: Input to wrapper %s
threegEnable: spawning command %s
threegMgmtHandler: query string: %s
threegMgmtHandler: returning with
status: %s
adding to dhcprealy ifgroup failed
DEBUG
DEBUG
DEBUG
adding to ipset fwDhcpRelay failed
Disabling Firewall Rule for DHCP Relay
Protocol
Enabling Firewall Rule for DHCP Relay
Protocol
prerouting Firewall Rule add for Relay
failed
prerouting Firewall Rule add for Relay
failed
DEBUG
%s: SQL get query: %s
%s: sqlite3QueryResGet failed
DEBUG
DEBUG
%s: no result found
DEBUG
Subnetaddress should be provided
with accessoption 2
Failed to restart sshd
unable to open the "
sqlite3QueryResGet failed.Query:%s
Error in executing DB update handler
Error in executing DB update handler
unknown vlan state
Failed to execute vlanConfig binary
for vlanId %d
sqlite3_mprintf failed
Access port can be present only in
single vlan
Failed to execute vlanConfig binary
for vlanId %d
unknown vlan state
Failed to execute vlanConfig binary
for port number %d
Failed to clear vlan for oldPVID %d
Failed to execute vlanConfig binary
for port number %d
Failed to clear vlan for %d
Failed to set vlan entry for vlan %d
Failed to set vlan entries, while
enabling \
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
163
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
sqlite3QueryResGet failed
Failed to execute vlanConfig binary
for port number %d
Failed to execute vlanConfig binary
for vlanId %d
Failed to enable vlan
Failed to disable vlan
Failed to set vlanPort table entries,
while \
Failed to enable vlan
unknown vlan state
ERROR
Error in executing DB update handler
unknown vlan state
Failed to execute vlanConfig binary
for vlanId %d
ERROR
ERROR
sqlite3_mprintf failed
Access port can be present only in
single vlan
Failed to execute vlanConfig binary
for vlanId %d
ERROR
unknown vlan state
Failed to execute vlanConfig binary
for port number %d
Failed to clear vlan for oldPVID %d
Failed to execute vlanConfig binary
for port number %d
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
%s: buffer overflow
%s: value of %s in %s table is: %s
DEBUG
DEBUG
Failed to clear vlan for %d
Failed to set vlan entry for vlan %d
Failed to set vlan entries, while
enabling \
Failed to execute vlanConfig binary
for port number %d
Failed to execute vlanConfig binary
for vlanId %d
Failed to enable vlan
Failed to disable vlan
Failed to set vlanPort table entries,
while \
Failed to enable vlan
unknown vlan state
threegMgmtInit: unable to open the
database file %s
threegConnEnable: failed to get the
WanMode
threegEnable:spawning failed
threegDisable: unable to kill ppp
daemon
ERROR
ERROR
%s: returning with status: %s
dnsResolverConfigure: addressFamily:
%d
dnsResolverConfigure: LogicalIfName:
%s
chap-secrets File found
PID File for xl2tpd found
DEBUG
pid: %d
options.xl2tpd file found
options.xl2tpd file not found
DEBUG
DEBUG
DEBUG
Conf File for xl2tpd found
DEBUG
xl2tpd.conf not found
Chap Secrets file found
DEBUG
DEBUG
Chap Secrets file not found
%s:DBUpdate event: Table: %s
opCode:%d rowId:%d
DEBUG
threegMgmtHandler: Query: %s
threegMgmtHandler: error in
executing database update
Error in executing DB update handler
are we getting invoked twice ??
could not open %s to append
could not write nameserver %s to %s
could not write nameserver %s to %s
could not open %s to truncate
dnsResolverConfigMgmtInit: unable
to open the "
resolverConfigDBUpateHandler:
sqlite3QueryResGet "
could not configure DNS resolver
dnsResolverConfigure: could not write
nameserver:%s,"
ERROR
chap-secrets File found
PID File for pptpd found
pid: %d
PID File for pptpd interface found
pid: %d
options.pptpd file found
options.pptpd file not found
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Conf File for pptpd found
DEBUG
pptpd.conf not found
Chap Secrets file found
DEBUG
DEBUG
Chap Secrets file not found
%s:DBUpdate event: Table: %s
opCode:%d rowId:%d
DEBUG
ERROR
DEBUG
DEBUG
DEBUG
unboundMgmt: unable to open the "
ioctl call Failed-could not update
active user Details
sqlite3QueryResGet failed.Query:%s
Can't kill xl2tpd
chap-secrets File found
pppoeMgmtTblHandler: MtuFlag: %d
pppoeMgmtTblHandler: Mtu: %d
pppoeMgmtTblHandler:
IdleTimeOutFlag: %d
pppoeMgmtTblHandler:
IdleTimeOutValue: %d
pppoeMgmtTblHandler: UserName: %s
pppoeMgmtTblHandler: Password: %s
pppoeMgmtTblHandler: DNS specified:
%s
pppoeMgmtTblHandler: Service: %s
pppoeMgmtTblHandler: StaticIp: %s
DEBUG
xl2tpd restart failed
ERROR
DEBUG
DEBUG
DEBUG
failed to get field value
failed to get field value
sqlite3QueryResGet failed.Query:%s
ERROR
ERROR
ERROR
DEBUG
DEBUG
DEBUG
sqlite3QueryResGet failed.Query:%s
unboundMgmt: unable to open the "
writing options.xl2tpd failed
ERROR
ERROR
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
164
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
pppoeMgmtTblHandler: NetMask: %s
pppoeMgmtTblHandler: AuthOpt: %d
pppoeMgmtTblHandler: Satus: %d
pppoeEnable: ppp dial string: %s
pppoeMgmtDBUpdateHandler: returning
with status: %s
pptpMgmtTblHandler: MtuFlag: %d
DEBUG
DEBUG
DEBUG
DEBUG
xl2tpdStop failed
writing xl2tpd.conf failed
writing options.xl2tpd failed
xl2tpdStop failed
ERROR
ERROR
ERROR
ERROR
DEBUG
DEBUG
ERROR
ERROR
pptpMgmtTblHandler: Mtu: %d
pptpMgmtTblHandler: IdleTimeOutFlag:
%d
pptpMgmtTblHandler: IdleTimeOutValue:
%d
pptpMgmtTblHandler: GetDnsFromIsp:
%d
DEBUG
xl2tpdStart failed
sqlite3QueryResGet failed.Query:%s
writing Chap-secrets/Pap-Secrets
failed
DEBUG
xl2tpdStop failed
ERROR
DEBUG
xl2tpdStart failed
ERROR
DEBUG
ERROR
pptpMgmtTblHandler: UserName: %s
pptpMgmtTblHandler: Password: %s
pptpMgmtTblHandler: dynamic MyIp
configured
pptpMgmtTblHandler: MyIp: %s
DEBUG
DEBUG
sqlite3QueryResGet failed.Query:%s
writing Chap-secrets/Pap-Secrets
failed
xl2tpdStop failed
ERROR
ERROR
pptpMgmtTblHandler: ServerIp: %s
pptpMgmtTblHandler: StaticIp: %s
pptpMgmtTblHandler: NetMask: %s
pptpMgmtTblHandler:
MppeEncryptSupport: %s
pptpMgmtTblHandler: SplitTunnel: %s
pptpEnable: ppp dial string: %s
pptpEnable: spawning command %s
PID File for dhcpc found
pid: %d
pptpMgmtDBUpdateHandler: query
string: %s
pptpMgmtDBUpdateHandler: returning
with status: %s
dhcpcReleaseLease: dhcpc release
command: %s
dhcpcMgmtTblHandler: MtuFlag: %d
dhcpcMgmtTblHandler: Mtu: %d
DHCPv6 Server started successfully.
DEBUG
DEBUG
DEBUG
xl2tpdStart failed
sqlite3QueryResGet failed.Query:%s
writing Chap-secrets/Pap-Secrets
failed
Error in executing DB update handler
unboundMgmt: unable to open the "
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Can't kill pptpd
pptpd restart failed
Can't kill pptpd
failed to get field value
failed to get field value
unboundMgmt: unable to open the "
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
DEBUG
writing options.pptpd failed
ERROR
DEBUG
pptpdStop failed
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
ERROR
ERROR
ERROR
ERROR
DHCPv6 Server stopped successfully
DHCPv6 Client started successfully.
DEBUG
DEBUG
DHCPv6 Client stopped successfully.
DEBUG
DHCPv6 Client Restart successful
DEBUG
l2tpMgmtTblHandler: MtuFlag: %d
DEBUG
l2tpMgmtTblHandler: Mtu: %d
DEBUG
l2tpMgmtTblHandler: IspName: %s
DEBUG
writing pptpd.conf failed
writing options.pptpd failed
pptpdStop failed
pptpdStart failed
writing Chap-secrets/Pap-Secrets
failed
Error in executing DB update handler
pppStatsUpdate: unable to get default
MTU
pppoeMgmtInit: unable to open the
database file %s
pppoeDisable: unable to kill ppp
daemon
pppoeMultipleEnableDisable: pppoe
enable failed
pppoeMultipleEnableDisable: pppoe
disable failed
DEBUG
DEBUG
165
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
l2tpMgmtTblHandler: UserName: %s
DEBUG
l2tpMgmtTblHandler: Password: %s
DEBUG
l2tpMgmtTblHandler: AccountName: %s
DEBUG
l2tpMgmtTblHandler: DomainName: %s
l2tpMgmtTblHandler: Secret: not
specified
DEBUG
l2tpMgmtTblHandler: Secret: %s
l2tpMgmtTblHandler: dynamic MyIp
configured
DEBUG
l2tpMgmtTblHandler: MyIp: %s
l2tpMgmtTblHandler: ServerIp: %s
l2tpMgmtTblHandler: StaticIp: %s
l2tpMgmtTblHandler: NetMask: %s
DEBUG
DEBUG
DEBUG
DEBUG
l2tpMgmtTblHandler: SplitTunnel: %s
needToStartHealthMonitor: returning with
status: %s
DEBUG
l2tpEnable: command string: %s
DEBUG
l2tpEnable: command: %s
DEBUG
l2tpEnable: command string: %s
DEBUG
PID File for dhcpc found
DEBUG
pid: %d
l2tpMgmtDBUpdateHandler: query string:
%s
l2tpMgmtDBUpdateHandler: returning
with status: %s
DEBUG
RADVD started successfully
RADVD stopped successfully
DEBUG
DEBUG
empty update. nRows=%d nCols=%d
WARN
Wan is not up or in load balencing mode
threegMgmtHandler: no row found.
nRows = %d nCols = %d
pppoeMgmtDBUpdateHandler: empty
update.
dhcpcEnable: dhclient already running
on: %s
WARN
dhcpcDisable: deleted dhclient.leases
l2tpMgmtInit: unable to open the
database file %s
l2tpEnable: unable to resolve address:
%s
WARN
l2tpEnable: inet_aton failed
ERROR
pppoeMgmtTblHandler: unable to get
current Mtu Option
pppoeMgmtTblHandler: unable to get
the Mtu
pppoeMgmtTblHandler: pppoe enable
failed
pppoeMgmtDBUpdateHandler: failed
query: %s
pppoeMgmtDBUpdateHandler: error
in executing "
pptpMgmtInit: unable to open the
database file %s
pptpEnable: error executing
command: %s
pptpEnable: unable to resolve
address: %s
pptpEnable: inet_aton failed
pptpEnable: inet_aton failed
pptpEnable:spawning failed
pptpDisable: unable to kill ppp
daemon
pptpMgmtTblHandler: unable to get
current MTU Option
pptpMgmtTblHandler: unable to get
the Mtu
pptpMgmtTblHandler:
dbRecordValueGet failed for %s "
pptpMgmtTblHandler: pptp enable
failed
pptpMgmtTblHandler: pptp disable
failed
pptpMgmtDBUpdateHandler:
sqlite3QueryResGet "
pptpMgmtDBUpdateHandler: error in
executing "
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
WARN
WARN
WARN
ERROR
ERROR
166
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Illegal invocation of dhcpConfig (%s)
dhcpLibInit: unable to open the
database file %s
sqlite3QueryResGet failed.Query:%s
dhcpcMgmtInit: unable to open the
database file %s
dhcpcReleaseLease: unable to
release lease
ERROR
dhcpcEnable: unable to kill dhclient
dhcpcEnable: enabling dhcpc failed
on: %s
ERROR
dhcpcDisable: unable to kill dhclient
dhcpcDisable: delete failed for
dhclient.leases
ERROR
dhcpcDisable: failed to reset the ip
dhcpcMgmtTblHandler: unable to get
current Mtu Option
dhcpcMgmtTblHandler: unable to get
the Mtu
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
ERROR
dhcpcMgmtTblHandler: dhclient
enable failed
dhcpcMgmtTblHandler: dhcpc release
failed
dhcpcMgmtTblHandler: dhcpc disable
failed
dhcpcMgmtDBUpdateHandler: failed
query: %s
dhcpcMgmtDBUpdateHandler: error
in executing "
ERROR
DHCPv6 Client start failed.
ERROR
ERROR
ERROR
DHCPv6 Client stop failed.
failed to create/open DHCPv6 client "
failed to write DHCPv6 client
configuration file
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
failed to restart DHCPv6 Client
failed to create/open DHCPv6 Server
Restoring old configuration..
DHCPv6 Server configuration update
failed
DHCPv6 Server Restart failed
sqlite3QueryResGet failed.Query:%s
Log Message
%d command not supported by eapAuth
pCtx NULL.
Current cert subject name= %s
X509_STORE_CTX_get_ex_data failed.
Cannot get cipher, no session est.
%s:
SSL_ERROR_WANT_X509_LOOKUP
Severity
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Log Message
PEAP key derive: ERROR
PEAP context is NULL: ERROR
Constructing P2 response: ERROR
innerEapRecv is NULL: ERROR
Decrypting TLS data: ERROR
Severity
ERROR
ERROR
ERROR
ERROR
ERROR
DEBUG
ERROR
err code = (%d) in %s
BIO_write: Error
Decrypting: BIO reset failed
Encrypting BIO reset: ERROR
BIO_read: Error
EAP state machine changed from %s to
%s.
EAP state machine changed from %s to
%s.
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Received EAP Packet with code %d
DEBUG
Response ID %d
Response Method %d
DEBUG
DEBUG
Wrong identity size: ERROR
Wrong size for extensions packet:
ERROR
innerEapRecv is NULL: ERROR.
Inner EAP processing: ERROR
TLS handshake: ERROR.
Sending P1 response: ERROR
Unexpected tlsGlueContinue return
value.
No more fragments in message.
ERROR
No phase 2 data or phase 2 data
buffer NULL: ERROR
Allocating memory for PEAP Phase 2
payload: ERROR
TLS encrypting response: ERROR
The Enable Command is %s
l2tpEnable:Executing the Command
failed
ERROR
l2tpDisable: command string: %s
ERROR
l2tpDisable: unable to stop l2tp session
l2tpMgmtTblHandler: unable to get
current MTU option
l2tpMgmtTblHandler: unable to get the
Mtu
l2tpMgmtTblHandler: dbRecordValueGet
failed for %s "
l2tpMgmtTblHandler: l2tpEnable failed
ERROR
l2tpMgmtTblHandler: disabling l2tp failed
l2tpMgmtDBUpdateHandler:
sqlite3QueryResGet "
l2tpMgmtDBUpdateHandler: error in
executing
Illegal invocation of tcpdumpConfig (%s)
ERROR
Failed to start tcpdump
Failed to stop tcpdump
Invalid tcpdumpEnable value
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Facility: System (VPN)
DEBUG
DEBUG
167
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
Created EAP/PEAP context: OK
DEBUG
Deleted EAP/PEAP context: OK
Upper EAP sent us: decision = %d
method state = %d
P2 decision=(%d); methodState=(%d)
Writing message to BIO: ERROR.
Encrypted (%d) bytes for P2
P2: sending fragment.
P2: message size = %d
P2: sending unfragmented message.
DEBUG
P1: Sending fragment.
DEBUG
P1: Total TLS message size = (%d)
P1: sending unfragmented message.
peapFragFirstProcess: TLS record size
to receive = (%d)
Setting version %d
PEAP pkt rcvd: data len=(%d) flags=(%d)
version=(%d)
Got PEAP/Start packet.
DEBUG
DEBUG
Got first fragment
DEBUG
Got fragment (n)
Got last fragment
DEBUG
DEBUG
Got unfragmented message
DEBUG
Got frag ack.
Ext AVP parsed: flags=(0x%x)
Mandatory bit not set: WARNING
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Ext AVP parsed: type=(%d)
DEBUG
Ext AVP parsed: value=(%d)
DEBUG
Got PEAPv0 success!
DEBUG
Got PEAPv0 failure!
DEBUG
pCtx NULL.
DEBUG
Authenticator response check: Error
Authenticator response check: Failed
MS-CHAP2 Response AVP size = %u
Created EAP/MS-CHAP2 context: OK.
pCtx NULL.
Deleted EAP/MS-CHAPv2 context: OK
Not authenticated yet.
Authenticator response invalid
EAP-MS-CHAPv2 password changed.
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
168
Setting message in fragment buffer:
ERROR
Allocating TLS read buffer is NULL:
ERROR
ERROR
ERROR
Setting last fragment: ERROR
Getting message: ERROR
Processing PEAP message: ERROR
Setting fragment: ERROR
Creating receive buffer: ERROR
Setting first fragment: ERROR
Sending P1 response: ERROR
NULL request (or response) PDU or
NULL context: ERROR
Expecting start packet, got something
else: ERROR
Protocol version mismatch: ERROR
Processing PEAP message (from
frag): ERROR
Processing PEAP message: ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Processing PEAP message: ERROR
Indicated length not valid: ERROR
Did not get Acknowledged result:
ERROR
Cannot understand AVP value:
ERROR
eapExtResp is NULL: ERROR
eapWscCtxCreate:
EAPAUTH_MALLOC failed.
eapWscProcess: umiIoctl req to WSC
failed, status = %d
eapWscCheck: Invalid frame
eapWscBuildReq: Invalid state %d
eapWscProcessWscResp: Invalid data
recd pData = %p, dataLen"
Data received for invalid context,
dropping it
eapWscProcessWscResp: Build
Request failed
eapWscProcessWscResp: Invalid
state %d
eapWscProcessWscResp: Message
processing failed 0x%X
eapWscProcessWscData: Invalid
notification recd %d
unable to initialize MD5
MDString: adpDigestInit for md5 failed
EAPAUTH_MALLOC failed.
EAPAUTH_MALLOC failed.
NULL context created: Error
NULL context received: Error
Authenticator ident invalid.
Success request message invalid:
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
Error
rcvd. opCode %d.
pCtx NULL.
TLS message len changed in the
fragment, ignoring.
no data to send while fragment ack
received.
TLS handshake successful.
Created EAP/TTLS context: OK
Deleted EAP/TTLS context: OK
No more fragments in message. ERROR
Upper EAP sent us: method state = %d;
decision = %d
P2: sending fragment.
DEBUG
DEBUG
Plugin context is NULL
Deriving implicit challenge: Error
ERROR
ERROR
DEBUG
Generating NT response: Error
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
NULL in/out buffer: Error
Incorrect vendor id.
Allocating memory for outBuff: ERROR
AVP code not recognized
EAPAUTH_MALLOC failed.
ERROR
ERROR
ERROR
ERROR
ERROR
DEBUG
DEBUG
ERROR
ERROR
P2 send unfragmented message.
P1: sending fragment.
DEBUG
DEBUG
P1: sending unfragmented message.
DEBUG
\tTLSMsgLen = 0x%x
Send req ptr = 0x%x; Send resp ptr =
0x%x
P2 decision=(%d); methodState=(%d)
Default EAP: method state = %d;
decision = %d
TTLS pkt: data len=(%d) flags=(0x%x)
DEBUG
Converting password to unicode: Error
Generating password hash: Error.
Generating password hash hash:
Error.
Generating master key: Error.
Generating first 16 bytes of session
key: Error.n
Generating second 16 bytes of session
key: Error.n
DEBUG
DEBUG
Converting password to unicode: Error
Constructing failure response: ERROR
ERROR
ERROR
DEBUG
DEBUG
ERROR
ERROR
Got start
Got first fragment (n).
DEBUG
DEBUG
Got fragment (n).
Got last fragment
Got unfragmented message.
DEBUG
DEBUG
DEBUG
Got frag ack.
Rcvd. AVP Code-%u: flags-0x%x: len%u: vendorId-%u: "
MOD EAP: method state from upper =
%d; decision = %d
Got AVP len = %ul. Should be less than
16777215
AVP length extract: Error
pFB is NULL
Requesting message before assembly
complete
DEBUG
Error checking authenticator response.
Error generating NT response.
Username string more than 256 ASCII
characters: ERROR
Invalid Value-Size.
Invalid MS-Length. Got (%d), expected
(%d)
Error constructing response.
Got type (%d), expecting (%d)
Cannot handle message; opCode =
%d
DEBUG
EAPAUTH_MALLOC failed.
ERROR
DEBUG
tlsGlueCtxCreate failed.
client certificate must be set in the
profile.
received tls message length too big.
total frags len > initial total tls length.
ERROR
ERROR
pFB is NULL
pFB is NULL
DEBUG
DEBUG
Buffer cannot hold message: ERROR
pFB is NULL: Error
pFB is NULL
TLS_FB* is NULL.
DEBUG
DEBUG
DEBUG
DEBUG
total frags len > initial total tls length.
total data rcvd(%d) doesnt match the
initial "
couldnt write %d data to TLS buffer.
invalid flags %s passed to
eapTlsBuildResp.
EAPAUTH_MALLOC failed.
tlsGlueCtxCreate failed.
Context NULL: ERROR
DEBUG
DEBUG
DEBUG
DEBUG
169
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
pFB->msgBuff is NULL.
Error calculating binary.
DEBUG
DEBUG
Error calculating binary.
DEBUG
adpDigestInit for SHA1 failed.
adpDigestInit for SHA1 failed.
DEBUG
DEBUG
E = %d
DEBUG
R = %d
Could not initialize des-ecb
DEBUG
DEBUG
adpDigestInit for MD4 failed.
DEBUG
adpDigestInit for SHA1 failed.
adpDigestInit for SHA1 failed.
Error converting received auth reponse to
bin.
Gnerating challenge hash: Error
Generating password hash: Error
Generating challenge response: Error
DEBUG
DEBUG
Conn cipher name=%s ver=%s: %s
Send req ptr = 0x%x; Send resp ptr =
0x%x
Request ptr = 0x%x;
Response ptr = 0x%x
Rcvd. AVP Code - %ul
Rcvd. AVP flags - 0x%02x
Rcvd. AVP len - %ul
Rcvd. AVP vendor id - %ul
\tCode = %d
\tIdent = %d
\tLen = %d
\tType = %d
\tOpCode = %d
\tMSID = %d
\tmsLen = %d
\tvalSize = %d
Frag Buffer bytes left = (%d)
Stripped username=(%s)
digestLen = %d.
ClearText =
DEBUG
CipherText =
DEBUG
digestLen = %d.
DEBUG
digestLen1 = %d.
DEBUG
digestLen2 = %d.
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
170
Setting profile to glue layer: ERROR.
_eapCtxCreate failed.
%d authentication not enabled in the
system.
Initializing inner non-EAP auth plugin:
ERROR
TTLS key derive: ERROR
TTLS context from EAP plugin is
NULL: ERROR
Allocating memory for TTLS Phase 2
payload: ERROR
TLS Encrypting response: ERROR
Allocating TLS read buffer is NULL:
ERROR
Inner authentication (id: %d)
unhandled
innerEapRecv is NULL: ERROR.
ERROR
ERROR
Decrypting TLS data: ERROR
Processing Phase 2 method: Error
Writing message to BIO: ERROR.
TLS handshake: ERROR.
Unexpected tlsGlueContinue return
value.
NULL request (or response) PDU or
NULL context
Protocol version mismatch: ERROR
Creating receive buffer: ERROR
Setting first fragment: ERROR
Setting fragment: ERROR
Setting last fragment: ERROR
Getting message: ERROR
Processing TTLS message: ERROR
Processing TTLS message: ERROR
Processing TTLS message: ERROR
Decapsulating AVP: ERROR
Processing EAP receive: Error
AVP code not EAP: Error
Encapsulating AVP: ERROR
profile %s doesnt exist.
profile %s is in use.
profile %s already exists.
EAPAUTH_MALLOC failed
User not found.
EAP-MD5 not enabled in system
configuration.
EAP-MSCHAPV2 not enabled in
system configuration.
EAP-TLS not enabled in system
configuration.
EAP-TTLS not enabled in system
configuration.
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
password change is not allowed for this
user
DEBUG
completed writing the policy
DEBUG
completed writing the SA
DEBUG
completed writing the proposal block
DEBUG
cmdBuf: %s
X509_DEBUG : Invalid Certificate for the
generated"
DEBUG
X590_ERROR : Failed to create File '%s'
DEBUG
x509TblHandler
DEBUG
pCertType: %s
DEBUG
pRowQueryStr: %s
DEBUG
x509SelfCertTblHandler
pRowQueryStr: %s
%s:DBUpdate event: Table: %s
opCode:%d rowId:%d
DEBUG
DEBUG
umiRegister failed
eapAuthHandler: Invalid data received
EAPAUTH_MALLOC failed.
malloc failed.
BIO_new_mem_buf failed.
malloc failed.
BIO_new_mem_buf failed.
SSL_CTX_new (TLSv1_client_method)
failed.
unable to set user configured CIPHER
list %s
Certificate verification failed.
Server name match failed. Got (%s)
expected "
SSL_CTX_use_certificate_file (cert,
PEM) failed.
SSL_CTX_use_PrivateKey_file failed.
private key does not match public key
SSL_CTX_load_verify_locations failed
SSL_new failed.
Both SSL_VERIFY_PEER and
SSL_VERIFY_NONE set: Error
EAPAUTH_MALLOC failed.
EAPAUTH_MALLOC failed.
eapTimerCreate failed.
eapCtxDelete:pCtx == NULL
eapRole != EAP_ROLE_PEER or
EAP_ROLE_AUTHENTICATOR
ERROR
ERROR
ERROR
DEBUG
DEBUG
EAP-PEAP not enabled in system
configuration.
EAP-WSC not enabled in system
configuration.
PAP not enabled in system
configuration.
CHAP not enabled in system
configuration.
MSCHAP not enabled in system
configuration.
MSCHAPV2 not enabled in system
configuration.
PAP/Token not enabled in system
configuration.
EAP-MD5 not enabled in system
configuration.
EAP-MSCHAPV2 not enabled in
system config.
EAP-TLS not enabled in system
configuration.
EAP-TTLS and EAP-PEAP are not
valid as inner"
invalid innerAuth %d.
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
profile %s doesnt exist.
Re-assembling fragments incorrect
size
Error creating cipher context.
Error initializing cipher context.
Error creating digest context.
Error initializing digest context.
Error initializing DES in Klite
Error initializing MD4 in Klite
ERROR
Error initializing RC4 in Klite
ERROR
ERROR
ERROR
Error initializing SHA in Klite
Error cleaning cipher context.
ERROR
ERROR
ERROR
Error destroying cipher context.
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Error cleaning digest context.
Error destroying digest context.
Error stripping domain name.
Error cleaning digest context.
Error cleaning digest context.
Challenge not present in failure
packet.
Wrong challenge length.
Incorrect password change version
value.
Error generating password hash.
Error generating password hash.
Error encrypting password hash with
block
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
171
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
pEapCtx == NULL or pPDU == NULL.
received EAP pdu bigger than
EAP_MTU_SIZE.
received EAP pdu bigger than
EAP_MTU_SIZE.
state machine is in invalid state.
unable to create method context.
method ctxCreate failed.
method profile set failed.
ERROR
Could not initialize des-ecb
ERROR
ERROR
Error cleaning cipher context.
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
state machine is in invalid state.
Only StandAlone authenticator supported
currently.
state machine is in invalid state.
BuildReq operation failed
No method ops defined for current
method
Process operation failed
state machine is in invalid state.
Packet length mismatch %d, %d
eapAuthTypeToType: Invalid
eapAuthType %d
eapTypeToAuthType: Invalid eapType
%d
unable to create method context.
method ctxCreate failed.
Invalid condition, methodState = %d,
respMethod = %d
A EAP Ctx map already exists
eapTimerCreate: Currently unsupported
for Peer role
eapTimerStart: Currently unsupported for
Peer role
eapTimerDestroy: Currently unsupported
for Peer role
eapTimerCancel: Currently unsupported
for Peer role
eapTimerHandler: Currently unsupported
for Peer role
pCtx is NULL: ERROR
tlsGlueCtxCreate failed
eapVars is NULL
Context NULL: ERROR
Initializing inner EAP auth: ERROR
pCtx is NULL: ERROR
Memory Allocation Failed
ERROR
Error cleaning cipher context.
Error cleaning digest context.
Error cleaning digest context.
adpDigestInit for SHA1 failed.
X509_ERROR : .Query:%s
X509_ERROR : Invalid Certificate for
the "
ERROR
ERROR
ERROR
invalid x509 certificate
Couldn't get the x509 cert hash
Memory allocation failed
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
FileName too lengthy
Couldn't execute command
Memory allocation failed
Memory allocation failed
ERROR
ERROR
ERROR
ERROR
ERROR
invalid certificate data
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
.Query:%s
.Query:%s
Memory allocation failed
X509_ERROR : Failed to validate the
certficate "
Memory allocation failed
ERROR
.Query:%s
ERROR
ERROR
Invalid Sign Key Length : %d
ERROR
ERROR
Invalid Hash Alg : %d
ERROR
ERROR
Invalid Sign Alg : %d
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
No Memory Available
Certificate Request Failed
File Open Failed
File is Empty
Memory Allocation Failed
File Open Failed
File is Empty
Error in executing DB update handler
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Severity
DEBUG
Log Message
unable to register to UMI
Severity
ERROR
ERROR
ERROR
ERROR
Facility: System (Admin)
Log Message
Usage:%s 
172
Unified Services Router
User Manual
Could not open database: %s
CPU LOG File not found
DEBUG
DEBUG
MEM LOG File not found
cpuMemUsageDBUpdateHandler:
update query: %s
DEBUG
Printing the whole list after inserting
%s at %d(minute) %d(hour)
%d(dayOfMonth) %d(month)"
DEBUG
adpCmdExec exited with return code=%d
DEBUG
%s op=%d row=%d
DEBUG
sqlite3_mprintf failed
DEBUG
sqlite3QueryResGet failed: query=%s
Printing the whole list after delete
%s at %d(minute) %d(hour)
%d(dayOfMonth) %d(month)"
DEBUG
DEBUG
Printing the whole list after inserting
%s at %d(minute) %d(hour)
%d(dayOfMonth) %d(month)"
DEBUG
email logs: No logging events enabled
DEBUG
%s
Mail sent and the Database is reset.
DEBUG
DEBUG
Disabled syslog server
DEBUG
Event logs are full, sending logs to email
DEBUG
Email logs sending failed
DEBUG
Packing attribute: %s
DEBUG
Server found: %s, secret: %s
Packed Auth. Reqest: code:%d, id:%d,
len:%d
DEBUG
Sending Packet to %x:%d ....
DEBUG
Receiving Reply Packet....
DEBUG
Verified Reply Packet Integrity
DEBUG
Generated Reply Attribute-Value pairs
DEBUG
Verified Message-Authenticator
Unloaded RADIUS Dictionary
DEBUG
DEBUG
Adding Dictionary Attribute %s
Adding Dictionary Value %s
Loaded Dictionary %s
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
173
sqlite3QueryResGet failed
radSendtoServer: socket: %s
radSendtoServer: bind() Failed: %s:
%s
radRecvfromServer: recvfrom() Failed:
%s
radRecvfromServer: Packet too small
from %s:%d: %s
radCheckMsgAuth: Invalid MessageAuthenticator length in"
radDictLoad: couldn't open dictionary
%s: %s
radBuildAndSendReq: Invalid Request
Code %d
radPairAssign: bad attribute value
length
radPairAssign: unknown attribute type
%d
radPairNew: unknown attribute %d
radPairGen: Attribute(%d) has invalid
length
radPairValue: unknown attribute type
%d
radPairValueLen: unknown attribute
type %d
radPairLocate: Attribute(%d) has
invalid length
radPairUnpackDefault: UnknownAttribute[%d]:
radConfigure: can't open %s: %s
radConfigure: %s: line %d: bogus
format: %s
radConfAssert: No AuthServer
Specified
radConfAssert: No Default Timeout
Specified
radConfAssert: No Default Retry
Count Specified
radExtractMppeKey: Invalid MSMPPE-Key Length
radVendorMessage: Invalid Length in
Vendor Message
radVendorMessage: Unknown Vendor
ID received:%d
radVendorAttrGet: Invalid Length in
Vendor Message
radVendorAttrGet: Unknown Vendor
ID:%d
radVendorMessagePack: Unknown
Vendor ID:%d
radGetIPByName: couldn't resolve
hostname: %s
radGetHostIP: couldn't get hostname
radGetHostIP: couldn't get host IP
address
radius dictionary loading failed
Failed to set default timeout value
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
Adding Dictionary Attribute '%s'
DEBUG
Adding Dictionary Value %s
DEBUG
Receiving attribute: %s
Processing attribute: %s
Processing attribute: %s
Processing attribute: %s
Processing attribute: %s
radConfGet: "
Added Server %s:%d with "
Added Server %s:%d with "
Default Timeout Set to %d
Default Retry Count Set to %d
%s - %s : %d
Deleting Server %s:%d with "
Adding RowId:%d to Server %s:%d with "
rowIds: %d - %d
Deleting Server %s:%d with "
RADIUS Deconfigured
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Found Option %s on line %d of file %s
DEBUG
Setting Option %s with value %s
DEBUG
RADIUS Configured
DEBUG
%d : Server %s:%d with "
DBUpdate event: Table: %s opCode:%d
rowId:%d
Host IP address: %s
Adding Packet for existing cookie:%p
Adding Packet and cookie:%p
Releasing Packet and cookie:%p
Releasing Packet with cookie:%p
DEBUG
Received EAP-Identity from Pnac: %s
Filling User-Name: %s
Filling State:
Filling EAP-Message:
Filling Service-Type: %d
Filling Framed-MTU: %d
Received Access-Challenge from Server
Sending Reply EAP Packet to Pnac
Error sending packet to Pnac
RADIUS Authentication Failed; "
RADIUS Authentication Successful; "
Got Packet with cookie:%p
Next DNS Retry after 1 min
Next Synchronization after"
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
174
Failed to set default retries value
ERROR: incomplete DB update
information.
old values result does not contain 2
rows
sqlite3QueryResGet failed
empty update. nRows=%d nCols=%d
Error in executing DB update handler
sqlite3QueryResGet failed
Invalid SQLITE operation code - %d
sqlite3QueryResGet failed
empty result. nRows=%d nCols=%d
sqlite3QueryResGet failed
empty result. nRows=%d nCols=%d
RADIUS Accounting Exchange Failed
Unable to set debug for radAcct.
Unable to set debug level for radAcct.
ERROR: option value not specified
ERROR: option value not specified
Unable to initialize radius
radEapMsgQueueAdd: Invalid EAP
packet length(%d)
radEapRecvTask: invalid EAP
code:%d
radEapRecvTask: Packet length
mismatch %d, %d
No attributes received in AccessChallenge message
No State Attribute in AccessChallenge message
radEapRecvTask: "
failed to initialize UMI
umiRegister failed. errno=%d
Invalid arguments to ioctl handler
radEapSendRtn: Invalid Arguments
radEapSendRtn: failed to allocate
buffer
umiIoctl failed
failed to initialize EAP message queue
Unable to set debug for radEap.
Unable to set debug level for radEap.
ERROR: option value not specified
ERROR: option value not specified
could not initialize MGMT framework
Unable to initialize radius
Unable to set debug for radEap.
Unable to set debug level for radEap.
ERROR: option value not specified
Unable to initialize radius
Invalid username or password
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
Next Synchronization after"
Next Synchronization after %d \
Primary is not available, "
Secondary is not available, "
DEBUG
DEBUG
DEBUG
DEBUG
ERROR
ERROR
ERROR
ERROR
DEBUG
DEBUG
DEBUG
Unable to set debug for radAuth.
Unable to set debug level for radAuth.
ERROR: option value not specified
Unable to initialize radius
Invalid username, challenge or
response
Unable to set debug for radAuth.
Unable to set debug level for radAuth.
ERROR: option value not specified
Unable to initialize radius
Invalid username or password
usage : %s 
ntpd : umi initialization failed
ntpd : ntpInit failed
ntpd : ntpMgmtInit failed
There was an error while getting the
timeZoneChangeScript."
unexpected reply from %d cmd=%d !
cmd %d not supported. caller %d
default reached
Unable to initialize ntpControl
ntpMgmt : Couldn't open database %s
ERROR : incomplete DB update
information
empty update. nRows=%d nCols=%d
Error in executing DB update handler
Invalid value for use default servers, "
No server is configured, "
Backing off for %d seconds
Requesting time from %s
Synchronized time with %s
Received KOD packet from %s
No suitable server found %s
Received Invalid Length packet from %s
Received Invalid Version packet from %s
Received Invalid Mode packet from %s
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Request Timed out from %s
Looking Up %s
Timezone difference :%d
Could not open file: %s
Could not read data from file
ntpTblHandler
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
status: %d
tz: %d
DayLightsaving: %d
pNtpControl>ServerNames[PRIMARY_SERVER]:
%s
pNtpControl>ServerNames[SECONDARY_SERVER]
: %s
DEBUG
requestNtpTime: Invalid addr
ERROR
DEBUG
failed to take lock for compId: %d
failed to convert ioctl args to buffer
for"
request timeout dst(%d) <-- src(%d)
failed to take lock for compId: %d
umiIoctlArgsToBuf: failed to allocate
memory
umiRecvFrom: could not allocate
memory
adpMalloc failed
context with ID: %d already registered
Failed to allocate memory for creating
UMI context
Failed to create recvSem for UMI
context
Failed to create mutex locks for UMI
context
Failed to create mutex recvQLock for
UMI context
Invalid arguments to umiIoctl
could not find the destination context
ERROR
DS: %d
pPriServ %s
pSecServ %s
DEBUG
DEBUG
DEBUG
Making request from %d --> %d
sent request dst(%d) <-- src(%d) using
option %d
received request too small!(%d bytes)
Received a UMI request from %d
DEBUG
sent a reply src(%d) ---> dst(%d)
DEBUG
umiRegister (%x,%x,%x,%x)
srcId=%d(%s) --> destId=%d(%s)
cmd=%d inLen=%d outLen=%d
DEBUG
waiting for reply...Giving Up
No request in the list after semTake
reply timeout
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
175
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
timeout after semTake
srcId=%d(%s) <-- destId=%d(%s)
cmd=%d
DEBUG
memPartAlloc for %d size failed
ERROR
DEBUG
ERROR
Un-registerting component with Id %d
failed to send ioctl request: dst(%d) <--src(%d)
processed a reply dst(%d) <-- src(%d)
request with no result option dst(%d) <-src(%d)
DEBUG
cmd = %s
cmdstring is %s %s:%d
Calling printerConfig binary ...
DEBUG
DEBUG
DEBUG
Calling unmount for USB ...
DEBUG
Calling mount for USB ...
usbdevice is %d %s:%d
Query string: %s
sqlite3QueryResGet failed.Query:%s
%s: 1. usb is already disconnected for
old usb type. "
%s: 2.call disable for new usb type !
%s: 3. usb is already disconnected for
old usb type. "
%s: 4. Disabled old usb type . Now "
usbdevice is %d %s:%d
USB: failed to begin transaction: %s
USB: SQL error: %s pSetString = %s
DEBUG
DEBUG
DEBUG
DEBUG
memPartAlloc for %d size failed
No Handler registered for this UMI
context
Couldn't find component with ID
(%d),"
id=%d handler=%x
Received NULL buffer in
umiBufToIoctlArgs()
usbMgmtInit: unable to open the
database file %s
call to printConfig failed
Failed to Disable Network Storage"
Some error occurred while removing
device
Some error occurred while removing
device
Sqlite update failed
Failed to enable printer properly
Failed to mount device on system
Failed to enable network storage
device"
Failed to mount device on system
ERROR
ERROR
ERROR
ERROR
ERROR
USB: failed to commit transaction: %s
DEBUG
USB: updated table: %s
USB: returning with status: %s
%s:DBUpdate event: Table: %s
opCode:%d rowId:%d
executing %s status =%d
executing %s
%s returned status=%d
%s returned status=%d
snmpd.conf not found
DEBUG
DEBUG
Sqlite update failed
USB1 Touch failed
USB2 Touch failed
Sqlite update failed
Failed query: %s
Failed to execute usb database
update handler
Usage:%s  
 
Illegal invocation of snmpConfig (%s)
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
[SNMP_DEBUG] : Fwrite Successful
DEBUG
[SNMP_DEBUG] : Fwrite failed
radPairGen: received unknown attribute
%d of length %d
radPairGen: %s has unknown type
radPairLocate: unknown attribute %ld of
length %d
radPairLocate: %s has unknown type
Illegal invocation of cpuMemUsage (%s)
DEBUG
Invalid Community Access Type
Invalid User Access Type
Invalid Security Level
Invalid Authentication Algorithm
Invalid Privacy Algorithm
Invalid Argument
Failed to allocate memory for
engineID
[SNMP_DEBUG]: Failed to get host
address
WARN
WARN
[SNMP_DEBUG] : FOPEN failed
sqlite3QueryResGet failed.Query:%s
ERROR
ERROR
WARN
WARN
ERROR
sqlite3QueryResGet failed.Query:%s
Invalid Security Level
Invalid Authentication Algorithm
ERROR
ERROR
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
176
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
cpuMemUsageDBUpdateHandler: SQL
error: %s
unable to open the DB file %s
umiInit failed
unable to register to UMI
Error Reading from the Database.
short DB update event request!
User Manual
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Error in executing DB update handler
adpListNodeRemove : Returned with an
error
command too long. Try increasing "
failed to allocate memory for
CRON_NODE
sqlite3QueryResGet failed
There was an error while reading the
schedules.
unable to register to UMI
short DB update event request!
malloc(DB_UPDATE_NODE) failed
short ifDev event request!
sqlite3_mprintf failed
ERROR
Invalid Privacy Algorithm
Failed to Get Host Address
Invalid version
snmp v3 Trap Configuration Failed
sqlite3QueryResGet failed query:%s
sqlite3QueryResGet failed.Query:%s
Failed to Open Snmp Configuration
File
ERROR
ERROR
Failed to write access control entries
Failed to write snmpv3 users entries
ERROR
ERROR
ERROR
ERROR
Failed to write snmp trap entries
Failed to write system entries.
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
no component id matching %s
umiIoctl (%s,
UMI_CMD_DB_UPDATE(%d)) failed.
ERROR
Failed to restart snmp
%s failed with status
Error in executing DB update handler
%s: Unable to open file: %s
RADVD start failed
RADVD stop failed
failed to create/open RADVD
configuration file %s
ERROR
sqlite3_mprintf failed
sqlite3_mprintf failed
no component id matching %s
umiIoctl (%s,
UMI_CMD_IFDEV_EVENT(%d)) failed.
klogctl(9) failed
malloc failed for %d bytes
klogctl(4) failed
emailLogs: Invalid Number of
Arguments!! Exiting.
sqlite3QueryResGet failed
Could not execute the smtpClient.
Error while cleaning the
database.Exiting. %s
ERROR
ERROR
ERROR
Restoring old configuration..
failed to write/update RADVD
configuration file
upnpDisableFunc failed
upnpEnableFunc failed
ERROR
ERROR
ERROR
ERROR
sqlite3QueryResGet failed.Query:%s
Error in executing DB update handler
unable to open the DB file %s
umiInit failed
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
unable to register to UMI
short DB update event request!
short ifDev event request!
ERROR
ERROR
ERROR
ERROR
sqlite3_mprintf failed
%s failed. status=%d
ERROR
ERROR
Severity
DEBUG
DEBUG
DEBUG
DEBUG
Log Message
Disable all NAT rules.
Enable all NAT rules.
Enabling NAT URL filter rules.
Restarting all NAT rules.
Severity
DEBUG
DEBUG
DEBUG
DEBUG
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Facility: System (Firewall)
Log Message
Enabling rule for protocol binding.
Disabling rule for protocol binding.
Enabling Remote SNMP on WAN.
Disabling Remote SNMP on WAN
177
Unified Services Router
User Manual
wan traffic counters are restared
DEBUG
Traffic limit has been reached
Traffic meter monthly limit has been
changed to %d.
Enabling traffic meter for only dowload.
Enabling traffic meter for both directions.
Enabling traffic meter with no limit.
Email alert in traffic meter disabled.
Email alert in traffic meter enabled.
Traffic Meter:Monthly limit %d MB has
been "
Traffic Metering: Adding rule to drop all
traffic
Traffic Metering: %sabling Email traffic
Disabling attack checks for IPv6 rules.
DEBUG
Enabling attack checks for IPv6 rules.
Configuring one to one NAT settings with
%s private start IP "
Deleting forward one to one NAT having
setting %s private start"
Disabling attack check for Block ping to
WAN interface.
Disabling attack check for Stealth mode
for tcp
Disabling attack check for Stealth mode
for udp
DEBUG
Disabling attack check for TCP Flood.
DEBUG
Disabling attack check for UDP Flood.
DEBUG
Disabling attack check for IPsec.
Disabling attack check for PPTP.
Disabling attack check for L2TP.
DEBUG
DEBUG
DEBUG
Disabling attack check for UDP Flood.
DEBUG
Disabling attack check for IPsec.
DEBUG
Disabling attack check for PPTP.
DEBUG
Disabling attack check for L2TP.
Enabling attack check for Block ping to
WAN "
Enabling attack check for Stealth Mode
for tcp.
Enabling attack check for Stealth Mode
for udp.
DEBUG
Enabling attack check for TCP Flood.
Enabling attack check for UDP Flood.
Enabling attack check for IPsec.
Enabling attack check for PPTP.
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Deleting schedule based firewall rules.
Deleting schedule based firewall rules
from DB.
Update schedule based firewall rules in
DB.
Restart schedule based firewall rules.
inter vlan routing enabled
inter vlan routing disabled
Disabling Content Filter for %d
Enabling Content Filter for %d
./src/firewall/linux/user/firewalld.c:59:#u
ndef ADP_DEBUG2
./src/firewall/linux/user/firewalld.c:61:#d
efine ADP_DEBUG2 printf
Enabling Source MAC Filtering
Disabling Source MAC Filtering
Adding MAC Filter Policy for Block &
Permit Rest
Adding MAC Filter Policy for Permit &
Block Rest
DEBUG
Restarting Source MAC Address Policy
Disabling Firewall Rule for DHCP Relay
Protocol
Enabling Firewall Rule for DHCP Relay
Protocol
prerouting Firewall Rule add for Relay
failed
prerouting Firewall Rule add for Relay
failed
Deleting MAC Filter Policy for Address
%s
Adding MAC Filter Policy for Address
%s
Disabling Firewall Rules for DMZ host
Enabling Firewall Rules for DMZ host
Disabling Firewall Rules for Spill Over
Load Balancing
Disabling Firewall Rules for Load
Balancing
Enabling Firewall Rules for Load
Balancing
Enabling Firewall Rules for Spill Over
Load Balancing
Enabling Firewall Rules for Auto
Failover
Enabling Firewall Rules for Load
Balancing .
Enabling Firewall Rules for Spill Over
Load Balancing .
Enabling Firewall Rules for Auto
Failover
Deleting BlockSites Keyword \
Enabling BlockSites Keyword \
Disabling BlockSites Keyword \
DEBUG
178
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Unified Services Router
User Manual
Enabling attack check for L2TP.
Enabling attack check for UDP Flood.
Enabling attack check for IPsec.
Enabling attack check for PPTP.
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Updating BlockSites Keyword from \
Inserting BlockSites Keyword \
Deleting Trusted Domain \
Adding Trusted Domain \
Restarting Schedule Based Firewall
Rules
Enabling attack check for L2TP.
Enabling DoS attack check with %d
SyncFlood detect rate, "
Disabling DoS attack check having %d
SyncFlood detect rate,"
Enabling ICSA Notification Item for ICMP
notification.
Enabling ICSA Notification Item for
Fragmented Packets.
Enabling ICSA Notification Item for Multi
cast Packets.
Disabling ICSA Notification Item for
ICMP notification.
Disabling ICSA Notification Item for
Fragmented Packets.
Disabling ICSA Notification Item for Multi
cast Packets.
Adding IP/MAC binding rule for %s MAC
address "
Deleting IP/MAC binding rule for %s
MAC "
./src/firewall/linux/user/firewalld.c:60:#un
def ADP_DEBUG
./src/firewall/linux/user/firewalld.c:62:#def
ine ADP_DEBUG printf
Restarting traffic meter with %d mins,
%d hours, "
Updating traffic meter with %d mins, %d
hours, "
DEBUG
Enabling Remote SNMP
DEBUG
DEBUG
Disabling Remote SNMP
DEBUG
DEBUG
Enabling Remote SNMP
DEBUG
DEBUG
Disabling DOS Attacks
DEBUG
DEBUG
Enabling DOS Attacks
DEBUG
DEBUG
Enabling DOS Attacks
DEBUG
DEBUG
DEBUG
DEBUG
Restarting Firewall [%d]:[%d] For %s
restartStatus = %d for LogicalIfName =
%s
DEBUG
Deleting Lan Group %s
DEBUG
DEBUG
Adding Lan Group %s
DEBUG
DEBUG
Deleting lan host %s from group %s
DEBUG
DEBUG
Adding lan host %s from group %s
Disabling Firewall Rule for IGMP
Protocol
Enabling Firewall Rule for IGMP
Protocol
Deleting IP/MAC Bind Rule for MAC
address %s and IP "
Adding IP/MAC Bind Rule for MAC
address %s and IP
Deleting Protocol Bind Rule for Service
%s
Deleting Protocol Bind Rule for Service
%s
Deleting Protocol Bind Rule for Service
%s
Adding Protocol Bind Rule for Service
%s
%s Session Settings
Restarting IPv6 Firewall Rules...
Deleting Port Trigger Rule for
%d:%d:%d:%d:%d
Deleting Port Trigger Rule for
%d:%d:%d:%d:%d
Enabling Port Trigger Rule for
%d:%d:%d:%d:%d
Disabling Port Trigger Rule for
%d:%d:%d:%d:%d
Enabling Port Trigger Rule for
DEBUG
Deleting traffic meter.
DEBUG
Disabling block traffic for traffic meter.
DEBUG
Enabling traffic meter.
DEBUG
Adding lan group %s.
DEBUG
Deleting lan group %s.
DEBUG
Renaming lan group from %s to %s.
Deleting host %s from %s group.
Adding host %s to %s group.
Enabling Keyword blocking for %s
keyword.
Disabling keyword Blocking for %s
keyword .
Deleting trusted domain with keyword
%s.
DEBUG
DEBUG
DEBUG
Adding %s keyword to trusted domain.
Enabling Management Access from
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
179
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Unified Services Router
Internet on port %d
Enabling remote access management
for IP address range"
Enabling remote access management to
only this PC.
Disabling Management Access from
Internet on port %d
Disabling remote access management
for IP address range"
Disabling remote access management
only to this PC.
MAC Filtering %sabled for BLOCK and
PERMIT REST.
MAC Filtering %sabled for PERMIT and
BLOCK REST.
Enabling Content Filtering.
Disabling Content Filtering.
Deleting rule, port triggering for protocol
TCP.
Deleting rule, port triggering for protocol
UDP.
Deleting rule, port triggering for protocol
TCP.
Deleting rule, port triggering for protocol
UDP.
Enabling rule, port triggering for protocol
TCP.
Enabling rule, port triggering for protocol
UDP.
Enabling rule, port triggering for protocol
TCP.
Enabling rule, port triggering for protocol
UDP.
Enabling DNS proxy.
User Manual
DEBUG
DEBUG
%d:%d:%d:%d:%d
Disabling Port Trigger Rule for
%d:%d:%d:%d:%d
Adding Port Trigger Rule for
%d:%d:%d:%d:%d
DEBUG
Enabling Content Filter
DEBUG
DEBUG
Disabling Content Filter
DEBUG
DEBUG
Enabling Content Filter
Setting NAT mode for pLogicalIfName
= %s
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Enabling DROP for INPUT
Enabling DROP for FORWARD
Enabling NAT based Firewall Rules
Setting transparent mode for
pLogicalIfName \
DEBUG
Enabling Accept for INPUT
DEBUG
DEBUG
DEBUG
DEBUG
Enabling Accept for FORWARD
Setting Routing mode for
pLogicalIfName \
DEBUG
Enabling DROP for INPUT
DEBUG
DEBUG
Enabling DROP for FORWARD
DEBUG
DEBUG
Disabling NAT based Firewall Rules
Enabling Firewall Rules for URL
Filtering & "
Adding Firewall Rule for RIP Protocol
Restarting Schedule Based Firewall
Rules
enabling IPS checks between %s and
%s zones.
disabling IPS checks between %s and
%s zones.
Stopping IPS...%s
IPS started.
Route already exists
Route addition failed: Network
Unreachable
Route addition failed: Network is down
DEBUG
Route addition failed
Failed to add rule in iptables
Failed to delete rule from iptables
fwLBSpillOverConfigure: Something
going wrong here
fwLBSpillOverConfigure: unable to get
interfaceName
fwLBSpillOverConfigure: Could not set
PREROUTING rules
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Restarting DNS proxy.
DEBUG
checking DNS proxy for Secure zone.
DEBUG
checking DNS proxy for Public zone.
Enabling Block traffic from %s zone.
Configuring firewall session settings for "
Disabling DMZ
DEBUG
DEBUG
DEBUG
DEBUG
Disabling WAN-DMZ rules .
Enabling WAN DMZ rules .
Restarting DMZ rule having %s address
with %s address.
Enabling LAN DHCP relay.
OneToOneNat configured successfully
DEBUG
DEBUG
OneToOneNat configuration failed
DEBUG
Deleting scheduled IPv6 rules.
delete from FirewallRules6 where
ScheduleName = '%s'.
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
180
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
ERROR
ERROR
ERROR
Unified Services Router
User Manual
Update FirewallRules6 where
ScheduleName = '%s' to New "
DEBUG
DEBUG
fwLBSpillOverConfigure: Could not set
POSTROUTING rules
fwLBSpillOverConfigure: Something
going wrong Here
fwL2TPGenericRules.c: unable to open
the database file "
fwL2TPGenericRules.c: inet_aton failed
fwPPTPGenericRules.c: unable to
open the database file "
fwPPTPGenericRules.c: inet_aton
failed
DNS proxy firewall rule add failed for
%s
deleting interface %s from ifgroup %d
failed
adding interface %s to ifgroup %d
failed
nimfBridgeTblHandler: unable to get
interfaceName
Dns proxy Restart failed
DEBUG
deleting interface to ifgroup failed
adding interface to ifgroup failed
deleting interface pVirtIface %s from
ifgroup %d"
adding interface pVirtIface %s to ifgroup
%d failed
DEBUG
DEBUG
Deleting IP address %s.
DEBUG
Adding new IP address %s.
Updating old IP address %s to new IP
address %s.
Restarting Firewall For %s Address
Update from %s:%s
Disabling Firewall Rule for MSS packet
marking
Enabling Firewall Rule for MSS packet
marking
Enabling packet marking rule for %s
IDLE timer
Deleted firewall rule %s for service %s
with action %s
%s firewall rule %s for service %s with
action %s
Added firewall rule %s for service %s
with action %s
Deleting inbound(WAN-LAN) firewall
rule.
Deleting inbound(WAN-DMZ) firewall
rule.
RIPng disabled.
DEBUG
DEBUG
nimfBridgeTblHandler: \
ERROR
DEBUG
nimfBridgeTblHandler: unable to get \
Failed to %s traffic from %s to %s to
IPS.
Failed to %s traffic from %s to %s to
IPS.
ERROR
failed to start IPS service.
Timeout in waiting for IPS service to
start.
Usage:%s  
  "
ERROR
ERROR
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
xlr8NatConfig: illegal invocation of (%s)
Illegal invocation of [%s]
xlr8NatMgmtTblHandler: failed query:
%s
Could not open file: %s
Rip Error Command Too Long
No authentication for Ripv1
Invalid Rip Direction
Invalid Rip Version
Invalid Password for 1st Key
Invalid Time for 1st Key
Invalid Password for 2nd Key
RIPng enabled.
Disable IPv6 firewall rule.
Enable IPv6 firewall rule.
Deleting IGMP proxy rule.
Enable IGMP proxy rule.
Restarting IGMP rule.
Traffic meter enabled with no limit type.
Traffic meter enabled for only download.
Traffic meter enabled for both directions.
Deleted firewall rule %s for service %s
with action %s
%s firewall rule %s for service %s with
action %s
Added firewall rule %s for service %s
with action %s
Enabling Inter VLAN routing.
Updating inter VLAN routing status.
Deleting inter VLAN routing.
DEBUG
Invalid Time for 2nd Key
ERROR
DEBUG
Invalid First KeyId
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
Invalid Second KeyId
Invalid Authentication Type
ripDisable failed
ripEnable failed
ERROR
ERROR
ERROR
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
181
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
Facility: Local0 (Wireless)
Log Message
(node=%s) setting %s to val = %d
Custom wireless event: '%s'
Wireless event: cmd=0x%x len=%d
New Rogue AP
(%02x:%02x:%02x:%02x:%02x:%02x)
detected
WPS session in progress, ignoring
enrolle assoc request
Severity
DEBUG
DEBUG
DEBUG
Log Message
sqlite3QueryResGet failed
sqlite3QueryResGet failed
VAP(%s) set beacon interval failed
Severity
ERROR
ERROR
ERROR
DEBUG
VAP(%s) set DTIM interval failed
ERROR
DEBUG
ERROR
ran query %s
DBUpdate event: Table: %s opCode:%d
rowId:%d
%sing VAPs using profile %s
%sing VAP %s
ran query %s
%sing VAP instance %s
VAP(%s) set Short Preamble failed
VAP(%s) set Short Retry failed
VAP(%s) set Long Retry failed
Decrypting context with key %s
DEBUG
VAP(%s) set RTS Threshold failed
VAP(%s) set Fragmentation Threshold
failed
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unknown IAPP command %d received.
unexpected reply from %d cmd=%d !
unexpected reply from %d cmd=%d !
Recvied DOT11_EAPOL_KEYMSG
shutting down AP:%s
APCtx Found
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
APCtx Not-Found
DEBUG
node not found *:*:*:%x:%x:%x
error installing unicast key for %s
cmd =%d i_type =%d i_val=%d
join event for new node %s
wpa/rsn IE id %d/%d not supported
wpa IE id %d not supported
leave event for node %s
NodeFree request for node : %s
installing key to index %d
iReq.i_val : %d
pIfName : %s
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
iReq.i_val : %d
DEBUG
setting mode: %d
DEBUG
Global counter wrapped, re-generating...
DEBUG
VAP(%s) set Protection Mode failed
VAP(%s) set Tx Power failed
WDS Profile %s not found
Failed to initalize WPS on %s
failed to get profile %s
could not initialize MGMT framework
could not initialize MGMT framework
dot11VapBssidUpdt SQL error: %s
sqlite3QueryResGet failed.Query:%s
KDOT11_GET_PARAM(IEEE80211_I
OC_CHANNEL) failed
Failed to get the channel setting for %s
sqlite3QueryResGet failed.Query:%s
sqlite3QueryResGet failed.Query:%s
profile %s not found
sqlite3QueryResGet failed.Query:%s
Interface name and policy must be
specified
Interface name and policy must be
specified
invalid ACL type %d
interface name not specified
interface name not specified
Invalid interface - %s specified
buffer length not specified
Invalid length(%d) specified
failed created iappdLock
failed to create cipher contexts.
unable to register to UMI
iappSockInit() failed
iappInit got error, unregistering it with
UMI
umiIoctl(UMI_COMP_UDOT11,%d,%d
) failed
umiIoctl(UMI_COMP_KDOT11,%d,%d
) failed
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
182
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
Got
PNAC_EVENT_PREAUTH_SUCCESS
event for : %s
event for non-existent node %s
PNAC_EVENT_EAPOL_START event
received
PNAC_EVENT_EAPOL_LOGOFF event
received
PNAC_EVENT_REAUTH event received
PNAC_EVENT_AUTH_SUCCESS event
received
PNAC_EVENT_PORT_STATUS_CHAN
GED event received
User Manual
DEBUG
DEBUG
unsupported event %d from PNAC
event for non-existent node %s. Create
new node.
Add new node to DOT11 Node list
Update dot11STA database
Add PMKSA to the list
eapolRecvAuthKeyMsg: received key
message
DEBUG
UDP failed, received Length is %d
umiIoctl(UMI_COMP_KDOT11,
umiIoctl(UMI_COMP_UDOT11,%d,%d
)\
umiIoctl(UMI_COMP_KDOT11,%d,%d
)\
No IAPP Node found for req id %d
umiIoctl(UMI_COMP_UDOT11,%d,%d
)\
umiIoctl(UMI_COMP_KDOT11,%d,%d
)\
umiIoctl(UMI_COMP_UDOT11,%d,%d
) failed
DEBUG
DEBUG
DEBUG
DEBUG
UDP socket is not created
UDP send failed
IAPP: socket (SOCK_STREAM) failed.
IAPP: TCP connect failed to %s.
ERROR
ERROR
ERROR
ERROR
DEBUG
ERROR
node not found
eapolRecvKeyMsg: replay counter not
incremented
eapolRecvKeyMsg: replay counter is not
same
processing pairwise key message 2
RSN IE matching: OK
processing pairwise key message 4
processing group key message 2
processing key request message from
client
DEBUG
cmd %d not supported.sender=%d
umiIoctl(UMI_COMP_KDOT11,%d,%d
) failed
IAPP-CACHE-NOTIFY-REQUEST
send to
./src/dot11/iapp/iappLib.c:1314:
ADP_ERROR (
BSSID value passed is NULL
reserved requestId is passed
interface name is NULL
IP address value passed is NULL
ERROR
WPA version %2x %2x not supported
DEBUG
(%s) group cipher %2x doesn't match
DEBUG
(%s)Pairwise cipher %s not supported
(%s) authentication method %d not
supported
%s:Auth method=%s pairwise cipher=%s
IE size=%d
WPA version %2x %2x not supported
Unable to obtain IE of type %d
PTK state changed from %s to %s
using PMKSA from cache
PTK GK state changed from %s to %s
GK state changed from %s to %s
DEBUG
Sending PTK Msg1
Sending PTK Msg3
Sending GTK Msg1
DEBUG
DEBUG
DEBUG
opening receive UDP socket failed
enabling broadcast for UDP socket
failed
opening receive TCP socket for new
AP failed
./src/dot11/iapp/iappLib.c:1784:
ADP_ERROR(
./src/dot11/iapp/iappLib.c:1794:
ADP_ERROR(
./src/dot11/iapp/iappLib.c:1803:
ADP_ERROR(
failed created dot11dLock.
failed initialize profile library.
failed to create cipher contexts.
unable to register to UMI
could not create MIB tree
unable to register to PNAC
Max registration attempts by DOT11 to
PNAC exceeded
Creation of EAP WPS Profile Failed
umiIoctl(UMI_COMP_IAPP,%d ) failed
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
183
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
sending EAPOL pdu to PNAC...
creating pnac authenticator with values
%d %d - %s
Profile %s does not exist
IAPP initialized.
Encrypting context key=%s for
could not find access point context for
%s
join event for existing node %s
failed to send
PNAC_FORCE_AUTHORIZED "
failed to send PNAC_AUTHORIZED "
failed to send
PNAC_VAR_KEY_AVAILABLE (TRUE) "
failed to send PNAC_VAR_KEY_TX_EN
(TRUE) "
failed to send PNAC_VAR_KEY_TX_EN
(FALSE) "
failed to send
PNAC_FORCE_AUTHORIZED "
DEBUG
failed to send PNAC_AUTHORIZED "
mic verification: OK
DEBUG
DEBUG
pnacIfConfig: Invalid supplicant"
Failed to process user request
Failed to process user request - %s(%d)
pnacIfConfigUmiIoctl: umiIoctl failed
pnacIfConfigUmiIoctl: usrPnac returned
%d
pnacIfConfigUmiIoctl: usrPnac returned
%d
pnacIfConfigUmiIoctl: usrPnac returned
%d
pnacKernNotifier: invalid PAE
configuration "
From pnacEapDemoAuthRecv:
unsupported response "
From pnacEapDemoAuthRecv: invalid
codes received
From pnacRadXlateDemoRecv: received
unknown "
From pnacRadXlateDemoRecv: invalid
codes received
Error from pnacRadXlateDemoRecv:
malloc failed
From pnacRadXlateRadPktHandle:
received a non-supported"
Only md5 authentication scheme
currently supported. "
Message from authenticator:
from pnacPDUXmit: bufsize = %d,
pktType = %d,"
pnacPDUXmit: sending eap packet. code
= %d, "
DEBUG
DEBUG
DEBUG
DEBUG
DOT11_RX_EAPOL_KEYMSG:
unknown ifname %s
ERROR
ERROR
ERROR
ERROR
ERROR
DEBUG
DEBUG
cmd %d not supported.sender=%d
inteface name passed is NULL
BSSID passed is NULL
inteface name passed is NULL
unable to allocate memory for
DOT11_CTX
unable to install wme mapping on %s
DEBUG
DEBUG
unable to get %s mac address
Failed to set %s SSID
ERROR
ERROR
DEBUG
Failed to set SSID broadcast status
ERROR
DEBUG
Failed to set PreAuth mode
ERROR
DEBUG
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
unable to install key
KDOT11_SET_PARAM:IEEE80211_I
OC_AUTHMODE failed
KDOT11_SET_PARAM:IEEE80211_I
OC_PRIVACY failed
wpaInit failed
dot11InstallProfile: unable to get
interface index
adpHmacInit(%s) failed
interface %s not found
AP not found on %s
DEBUG
keyLen > PNAC_KEY_MAX_SIZE
ERROR
DEBUG
Invalid profile name passed
ERROR
DEBUG
Creation of WPS EAP Profile failed
ERROR
DEBUG
unsupported command %d
ERROR
DEBUG
device %s not found
ERROR
DEBUG
unsupported command %d
ERROR
DEBUG
dot11NodeAlloc failed
ERROR
DEBUG
Getting WPA IE failed for %s
ERROR
DEBUG
ERROR
DEBUG
DEBUG
Getting WPS IE failed for %s
Failed initialize authenticator for node
%s
Failed to get the system up time while
adding node %s
error creating PNAC port for node %s
DEBUG
dot11NodeAlloc failed
ERROR
DEBUG
Invalid arguments.
ERROR
DEBUG
DEBUG
184
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
pnacRecvRtn: no corresponding pnac
port pae found
sending unicast key
User Manual
DEBUG
DEBUG
umiIoctl(UMI_COMP_IAPP,%d) failed
Invalid IE.
umiIoctl(UMI_COMP_KDOT11_VAP,
%d ) failed
umiIoctl(UMI_COMP_KDOT11,%d
,%d) failed
KDOT11_SET_PARAM:IEEE80211_I
OC_WME_CWMIN failed
KDOT11_SET_PARAM:IEEE80211_I
OC_WME_CWMAX failed
KDOT11_SET_PARAM:IEEE80211_I
OC_WME_AIFS failed
KDOT11_SET_PARAM:80211_IOC_
WME_TXOPLIMIT failed
KDOT11_SET_PARAM:IEEE80211_I
OC_WME_ACM failed
KDOT11_SET_PARAM:IEEE80211_I
OC_WME failed
ERROR
ERROR
ERROR
sending broadcast key
from pnacAuthPAEDisconnected: calling
pnacTxCannedFail
from pnacAuthPAEForceUnauth: calling
pnacTxCannedFail
DEBUG
state changed from %s to %s
PNAC user comp id not set. dropping
event %d
DEBUG
sending event %d to %d
DEBUG
requesting keys informantion from %d
pnacUmiPortPaeParamSet: error in
getting port pae
pnacUmiPortPaeParamSet: invalid
param - %d
pnacRecvASInfoMessage: Skey of length
%d set
pnacRecvASInfoMessage: reAuthPeriod
set to: %d
pnacRecvASInfoMessage: suppTimeout
set to: %d
DEBUG
PORT SUCCESSFULLY DESTROYED
DEBUG
creating physical port for %s
pnacAuthInit: using defualt
pnacAuthParams
pnacSuppInit: using defualt
pnacSuppParams
Error from
pnacCombinedStMachTriggerFunc: "
Error from
pnacCombinedStMachTriggerFunc: "
Error from
pnacCombinedStMachTriggerFunc: "
Error from
pnacCombinedStMachTriggerFunc: "
Error from
pnacCombinedStMachTriggerFunc: "
Error from
pnacCombinedStMachTriggerFunc: "
Error from
pnacCombinedStMachTriggerFunc: "
Error from
pnacCombinedStMachTriggerFunc: "
Error from
pnacCombinedStMachTriggerFunc: "
received a pdu on %s
pnacRecvMapi: protoType: %04x
pPhyPort->authToASSendRtn:%p
DEBUG
invalid group cipher %d
KDOT11_SET_PARAM:IEEE80211_I
OC_MCASTCIPHER failed
KDOT11_SET_PARAM:IEEE80211_I
OC_MCASTKEYLEN failed
KDOT11_SET_PARAM:IEEE80211_I
OC_UCASTCIPHERS failed
KDOT11_SET_PARAM:IEEE80211_I
OC_KEYMGTALGS failed
KDOT11_SET_PARAM:IEEE80211_I
OC_WPA failed
DEBUG
unknow cipher type = %d
ERROR
DEBUG
umiIoctl(UMI_COMP_IAPP,%d) failed
ERROR
DEBUG
invalid media value=%d
ERROR
DEBUG
invalid mediaOpt value=%d
ERROR
DEBUG
invalid mode value=%d
ERROR
DEBUG
dot11PnacIfCreate failed
ERROR
DEBUG
wpaPRF failed
ERROR
DEBUG
Error generating global key counter
wpaCalcMic: unsupported key
descriptor version
integrity failed. need to stop all stations
couldn't find AP context for %s
interface
dot11Malloc failed
ERROR
ERROR
port not found
DEBUG
dot11Malloc failed
eapolRecvKeyMsg: unknown
descType =%d
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
185
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
from pnacRecvMapi: pkt body len = %d,
pktType = %d
from pnacPDUProcess: received
PNAC_EAP_PACKET
User Manual
from pnacPDUProcess: currentId = %d
from pnacPDUProcess: code = %d,
identifier = %d, "
from pnacPDUProcess: setting rxResp
true
from pnacPDUProcess: code = %d,
identifier = %d, "
DEBUG
from pnacPDUProcess: received "
DEBUG
from pnacPDUProcess: received "
from pnacPDUProcess: received
PNAC_EAPOL_KEY_PACKET
DEBUG
doing pnacTxCannedFail
DEBUG
doing pnacTxCannedSuccess
doing pnacTxReqId
DEBUG
DEBUG
doing pnacTxReq
DEBUG
doing pnacTxStart
DEBUG
doing pnacTxLogoff
DEBUG
doing pnacTxRspId: 1st cond
DEBUG
doing pnacTxRspId: entering 2nd cond
from pnacTxRspId: code = %d, identifier
= %d, length = %d, "
doing pnacTxRspId: 2nd cond
doing pnacTxRspAuth: 1st cond
doing pnacTxRspAuth: 2nd cond
message for unknown port PAE
from pnacACToSuppRecvRtn: calling
pnacEapPktRecord
from pnacEapPktRecord: code = %d,
identifier = %d, "
from pnacEapPktRecord: received
success pkt
from pnacEapPktRecord: received failure
pkt
from pnacEapPktRecord: received
request pkt
unknown EAP-code %d
Authenticator[%d]:
Auth PAE state = %s
Auth Reauth state = %s
Back auth state = %s
Supplicant[%d]:
Supp Pae state = %s
DEBUG
eapolRecvKeyMsg: invalid descriptor
version
eapolRecvKeyMsg: incorrect
descriptor version
eapolRecvKeyMsg: Ack must not be
set
eapolRecvKeyMsg: MIC bit must be
set
wpaAuthRecvPTKMsg2: unexpected
packet received
wpaAuthRecvPTKMsg2: mic check
failed
wpaAuthRecvPTKMsg2: rsn ie
mismatch
wpaAuthRecvPTKMsg4: unexpected
packet received
wpaAuthRecvPTKMsg4:
keyDataLength not zero
wpaAuthRecvPTKMsg4: mic check
failed
wpaAuthRecvGTKMsg2: unexpected
packet received
secureBit not set in GTK Msg2
wpaAuthRecvGTKMsg2:
keyDataLength not zero
wpaAuthRecvGTKMsg2: mic check
failed
wpaAuthRecvKeyReq: unexpected
packet received
wpaAuthRecvKeyReq: keyDataLength
not zero
wpaAuthRecvKeyReq: mic check
failed
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
invalid OUI %x %x %x
(%s) invalid OUI %x %x %x
[%s:%d] Cipher in WPA IE : %x
(%s) invalid OUI %x %x %x
short WPA IE (length = %d) received
ERROR
ERROR
ERROR
ERROR
ERROR
DEBUG
PTK state machine in unknown state.
ERROR
DEBUG
ERROR
DEBUG
dot11InstallKeys failed
group state machine entered into
WPA_AUTH_GTK_INIT
DEBUG
dot11Malloc failed
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
dot11Malloc failed
dot11Malloc failed
aesWrap failed
unknown key descriptor version %d
dot11Malloc failed
could not initialize AES128ECB
could not initialize AES-128-ECB
MD5 initialization failed
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
186
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
from pnacBackAuthFail: calling
pnacTxCannedFail
%s returned ERROR
pnacUmiIoctlHandler: cmd: %s(%d)
%s not configured for 802.1x
could not process PDU received from the
wire
pnacPDUForward: failed to foward the
received PDU
Creating PHY port with AUTH backend :
%s SendRtn: %p RecvRtn:%p
pnacUmiAuthConfig: %s not configured
for 802.1x
pnacSuppRegisterUserInfo: not a valid
AC
User Manual
DEBUG
DEBUG
DEBUG
DEBUG
RC4 framework initialization failed
PNAC framework initialization failed
ERROR: option value not specified
ERROR: -u can be used only with -s
ERROR
ERROR
ERROR
ERROR
DEBUG
ERROR: user-name not specified
ERROR
DEBUG
failed to enable debug
ERROR
DEBUG
[%s]: failed to convert string to MAC "
ERROR
DEBUG
ERROR
WARN
WARN
failed to initialize UMI
pnacPhyPortParamSet:invalid
arguments
pnacPhyPortParamSet:Failed to
create socket
Error from pnacPhyPortParamSet:%sdevice invalid
Error from pnacPhyPortParamSet:%sGetting MAC address "
pnacPhyPortParamSet:Failed to add
802.1X multicast "
pnacIsInterfaceUp: failed to create a
raw socket
pnacIsInterfaceUp: failed to get
interface flags
failed to allocate buffer
WARN
UMI initialization failed
ERROR
WARN
UMI initialization failed
Error from pnacEapDemoAuthLibInit:
malloc failed
Error from pnacEapDemoAuthRecv:
received null EAP pkt
Error from pnacEapDemoAuthRecv:
send "
Error from pnacRadXlateASAdd:
cannot open socket
Error from pnacRadXlateDemoRecv:
received null EAP pkt
ERROR
From pnacRadXlateDemoRecv: send "
Error from pnacRadXlateDemoRecv:
radius "
Error from pnacRadXlateDemoRecv:
radius "
Error from
pnacRadXlateRadIdRespSend: send
to failed
Error from
pnacRadXlateRadNonIdRespSend:
send to failed
Error from
pnacRadXlateRadRecvProc: recvfrom
failed
From
ERROR
DEBUG
pnacIfConfig: autoAuth Enabled
pnacSendRtn: no pnac port pae found for
DEBUG
sending portStatus: %s[%d] to dot11
pnacRecvASInfoMessage: Rkey of
length %d set
DEBUG
ASSendRtn: %p ASToAuthRecv: %p
adpRand failed:unable to generate
random unicast key
using group key as unicast key
Integrity check failed more than once in
last 60 secs.
MIC failed twice in last 60 secs, taking
countermeasures
DEBUG
Failed to set dot11 port status
WARN
PTK state machine in NO_STATE.
WARN
PTK state machine in NO_STATE!!
WARN
PMKSA refcount not 1
WARN
IV verification failednknown subtype>
pnacIfConfig: overwriting previous
interface "
WARN
pnacIfConfig: overwriting previous "
pnacIfConfig: overwriting previous
username"
WARN
DEBUG
DEBUG
WARN
WARN
pnacIfConfig: overwriting previous
password"
WARN
%s: Failed to set port status
WARN
%s: Failed to notify event to dot11
pnacLibDeinit: Failed to destroy the
WARN
WARN
187
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
phyPort:%s
pnacPortPaeDeconfig:kpnacPortPaeDec
onfig failed
pnacPortPaeDeconfig:kpnacPortPaeDec
onfig failed
WARN
WARN
pnacBackAuthSuccess: failed to notify
the destination "
WARN
could not initialize MGMT framework
ERROR
umiInit failed
ERROR
iappInit failed
ERROR
could not initialize IAPP MGMT.
ERROR
dot11Malloc failed
ERROR
buffer length not specified
Invalid length(%d) specified
Failed to get information about
authorized AP list.
Recd IE data for non-existent AP %s
Recd IE data for wrong AP %s
Received Invalid IE data from WSC
ERROR
ERROR
Recd IE data for non-existent AP %s
Recd WSC Start command without
interface name
ERROR
Recd WSC start for non-existent AP %s
ERROR
Recd WSC start for wrong AP %s
Unable to send
WSC_WLAN_CMD_PORT to WSC
Failed to get the ap context for %s
WPS can only be applied to WPA/WPA2
security profiles
ERROR
wpsEnable: running wsccmd failed
Failed to get the ap context for %s
WPS conf. under non WPA/WPA2
security setting
Failed to reset the Beacon Frame IE in
the driver
Failed to reset the Beacon Frame IE in
the driver
ERROR
ERROR
WPS method cannot be NULL
PIN value length should be a multiple of
4 !!
Failed to initiate PIN based association,
PIN = %s
ERROR
ERROR
ERROR
ERROR
ERROR
pnacRadXlateRadPktIntegrityChk: no
corresponding "
Error from
pnacRadXlateRadPktIntegrityChk: no
message "
Error from
pnacRadXlateRadPktIntegrityChk: "
From
pnacRadXlateRadChalPktHandle: no
encapsulated eap "
Error from
pnacRadXlateRadChalPktHandle:
malloc for eap "
Error from
pnacEapDemoSuppUserInfoRegister:
invalid "
Error from pnacEapDemoSuppRecv:
received null EAP pkt
Error from pnacEapDemoSuppRecv:
send ptr to pnac supplicant"
From pnacEapDemoSuppRecv: user
info not entered yet
Error from pnacEapDemoSuppRecv:
couldn't "
MDString: adpDigestInit for md5 failed
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
pnacUmiInit: UMI initialization failed
could not start PNAC task
invalid aruments
pnacIfNameToIndex failed
pnacPhyPortParamSet: device invalid
%s%d
pnacPhyPortParamSet: EIOCGADDR
ioctl failed
pnacPhyPortParamSet: multicast addr
add ioctl failed
pnacPhyPortParamUnset: multicast
addr del ioctl failed
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
pnacPDUXmit: Invalid arguments
pnacPDUXmit: failed to get M_BLK_ID
from pnacIsInterfaceUp: device %s%d
invalid
pnacRecvRtn: dropping received
packet as port is"
pnacSendRtn: Invalid arguments
pnacSendRtn: no physical port
corresponding to"
pnacSendRtn: dropping packet as
port"
pnacAuthBuildRC4KeyDesc:
adpEncryptInit(RC4) failed
pnacAuthBuildRC4KeyDesc:
adpCipherContextCtrl"
pnacDot11UserSet: incorrect buffer
length
ERROR
PNAC user component id not set.
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
188
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
Failed to initiate PBC based enrolle
association
Invalid association mode. (Allowed
modes : PIN/PBC)
User Manual
ERROR
ERROR
wpsEnable: running wsccmd failed
Failed to send QUIT command to WSC
from DOT11
Failed to clear off the WPS process
ERROR
missing profile name
A profile exists with the same name
Error in allocating memory for profile
missing profile name
missing profile name
Profile name and interface name must be
specified
Profile %s does not exist
Could not set profile %s on the interface
%s
missing profile name
Profile %s does not exist
ERROR
ERROR
Profile %s does not exist
ERROR
SSID should not be longer than %d
Profile %s does not exist
Profile %s does not exist
Profile %s does not exist
ERROR
ERROR
ERROR
ERROR
Profile %s does not exist
ERROR
Profile %s does not exist
ERROR
Profile %s does not exist
SSID not set. SSID is needed to
generate password hash
ERROR
Password string too big
ERROR
dot11Malloc failed
ERROR
Profile %s does not exist
Hex string should only have %d hex
chars
ERROR
dot11Malloc failed
ERROR
Profile %s does not exist
invalid key index %d. key index should
be 0-3.
ERROR
wepKey length incorrect
ERROR
Profile %s does not exist
ERROR
ERROR
ERROR
pnacKeyInfoGet:failed to allocate
buffer
PNAC user comp id not set. dropping
EAPOL key pkt
pnacUmiPortPaeParamSet: invalid
buffer received
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Error from pnacRecvASInfoMessage: "
pnacRecvASInfoMessage: "
pnacRecvASInfoMessage: Bad info
length
Error from pnacLibInit: malloc failed
could not create phy ports lock
could not create nodes ports lock
port exists for iface - %s
ERROR
ERROR
pnacPhyPortCreate failed
kpnacPhyPortCreate failed
ERROR
ERROR
ERROR
invalid argument
pnacAuthConfig: maxAuth limit
reached
pnacAuthConfig: malloc failed
Error from pnacAuthConfig: pAsArg
cannot be NULL
Error from pnacAuthConfig: receive
routine hook "
pnacAuthConfig: pnacAuthInit failed
kpnacPortPaeConfig failed
Invalid arguments
Error from pnacSuppConfig: malloc
failed
Error from pnacSuppConfig: receive
routine hook "
Error from pnacSuppConfig:
pnacSuppInit failed
ERROR
kpnacPortPaeConfig failed
pnacAuthDeconfig failed: pPortPae
NULL
Error from pnacPhyPortDestroy: port
not configured
pnacPhyPortDestroy: Failed to
deconfigure port
ERROR
pnacPhyPortParamUnset FAILED
Error from pnacPhyPortCreate: malloc
failed
Error from pnacPhyPortCreate:
pnacPhyPortParamSet"
error from pnacPhyPortCreate: malloc
failed
Error from pnacAuthInit:
pnacPortTimersInit failed
Error from pnacAuthInit:
pnacAuthPAEInit failed
ERROR
ERROR
ERROR
ERROR
189
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
Invalid Cipher type %d
Profile supports WEP stas,Group cipher
must be WEP
ERROR
Profile %s does not exist
ERROR
Profile %s does not exist
ERROR
Profile %s does not exist
invalid pairwise cipher type %d
ERROR
ERROR
Cipher %s is already in the list.
ERROR
Profile %s does not exist
ERROR
Invalid Cipher type %d
ERROR
Cipher %s not found in the list.
ERROR
Profile %s does not exist
ERROR
Profile %s does not exist
Auth method %s is already in the list
ERROR
ERROR
Profile %s does not exist
ERROR
Auth method %s not found in the list.
ERROR
Profile %s does not exist
ERROR
Profile %s does not exist
ERROR
Profile %s does not exist
invalid type value %d. supported values
are 1,2,3,4
ERROR
Profile %s does not exist
invalid type value %d. supported values
are 1,2,3,4
ERROR
Profile %s does not exist
invalid type value %d. supported values
are 1,2,3,4
ERROR
Profile %s does not exist
invalid type value %d. supported values
are 1,2,3,4
ERROR
Profile %s does not exist
invalid type value %d. supported values
are 1,2,3,4
ERROR
Profile %s does not exist
ERROR: incomplete DB update
information.
old values result does not contain 2 rows
sqlite3QueryResGet failed
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
190
Error from pnacAuthInit:
pnacAuthKeyTxInit failed
Error from pnacAuthInit:
pnacReauthTimerInit failed
Error from pnacAuthInit:
pnacBackAuthInit failed
Error from pnacAuthInit: pnacCtrlDirInit
failed
Error from pnacAuthInit:
pnacKeyRecvInit failed
Error from pnacSuppInit: malloc failed
Error from pnacSuppInit:
pnacPortTimersInit failed
Error from pnacSuppInit:
pnacKeyRecvInit failed
Error from pnacSuppInit:
pnacSuppKeyTxInit failed
Error from pnacSuppInit:
pnacSuppPAEInit failed
Error from pnacRecvRtn: invalid
arguments
Error from pnacRecvMapi:
unsupported PDU received
suppToACSendRtn returned not OK!
Error from pnacBasicPktCreate: malloc
failed
Error from pnacEAPPktCreate: basic
pkt create failed
Error from pnacTxCannedFail: eap pkt
create failed
Error from pnacTxCannedSuccess:
eap pkt create failed
Error from pnacTxReqId: eap pkt
create failed
Error from pnacTxReq: eap pkt create
failed
Error from pnacSendRespToServer:
malloc failed
Error from pnacSendRespToServer:
no AS configured
Error from pnacTxStart: basic pkt
create failed
Error from pnacTxStart: basic pkt
create failed
Error from pnacTxRspId: eap pkt
create failed
Error from pnacTxRspAuth: eap pkt
create failed
Error from pnacEapPktRecord: EAP
packet too"
Error from pnacEapPktRecord: "
from pnacBackAuthTimeout: calling
pnacTxCannedFail
hmac_md5: adpHmacContextCreate
failed
hmac_md5:adpHmacInit failed
pnacUmiIoctlHandler: invalid cmd: %d
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
Error in executing DB update handler
ERROR
sqlite3QueryResGet failed
ERROR: incomplete DB update
information.
old values result does not contain 2 rows
ERROR
sqlite3QueryResGet failed
ERROR
Error in executing DB update handler
ERROR
sqlite3QueryResGet failed.Query:%s
ERROR
sqlite3QueryResGet failed.Query:%s
ERROR
sqlite3QueryResGet failed.Query:%s
ERROR
sqlite3QueryResGet failed.Query:%s
ERROR
startStopVap failed to stop %s
ERROR
Invalid SQLITE operation code - %d
./src/dot11/mgmt/dot11Mgmt.c:1177:
ADP_ERROR (
only delete event expected on
dot11RogueAP.
ERROR
sqlite3QueryResGet failed
ERROR
unhandled database operation %d
ERROR
sqlite3QueryResGet failed
ERROR
failed to configure WPS on %s
ERROR
sqlite3QueryResGet failed
ERROR
sqlite3QueryResGet failed
ERROR
sqlite3QueryResGet failed
ERROR
sqlite3QueryResGet failed
ERROR
sqlite3QueryResGet failed
no VAP rows returned. expected one
multiple VAP rows returned. expected
one
ERROR
ERROR
sqlite3QueryResGet failed
ERROR
invalid query result. ncols=%d nrows=%d
ERROR
%s:VAP(%s) create failed
ERROR
sqlite3QueryResGet failed
ERROR
invalid query result. ncols=%d nrows=%d
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
191
pnacEapRadAuthSend: Invalid
arguments
pnacEapRadAuthSend: failed to
allocate inbuffer
ERROR
ERROR
pnacXmit : umiIoctl failed[%d]
pnacPDUForward: Invalid input
pnacPDUForward: error in getting port
pae information
pnacPDUForward: error allocating
memory
pnacUmiIfMacAddrChange: %s not
configured for 802.1x
pnacUmiIfMacAddrChange: could not
process PDU received"
pnacUmiPhyPortConfig: Invalid config
data
pnacUmiPhyPortConfig: Invalid
backend name specified
pnacUmiPhyPortConfig: could not
create PNAC physical"
pnacUmiAuthConfig: Invalid config
data
pnacUmiAuthConfig: Invalid backend
name specified
ERROR
ERROR
unable to create new EAP context.
unable to apply %s profile on the EAP
context.
pnacUmiAuthConfig: could not
configure PNAC PAE "
pnacUmiSuppConfig: Invalid config
data
pnacUmiSuppConfig: Invalid backend
name specified
pnacUmiSuppConfig: %s not
configured for 802.1x
pnacUmiSuppConfig: could not PNAC
port Access"
pnacUmiSuppConfig: Failed to register
user information
pnacPortByMacDeconfig: port not
found
pnacPortByMacDeconfig: port not
found
pnacUmiIfDown: Invalid config data
ERROR
pnacUmiIfDown: Invalid config data
Error from pnacPortDeconfig: port not
configured
pnacUmiIfDown: could not deconfigure port
pnacUmiPhyPortDestroy: Invalid
config data
pnacUmiPhyPortDestroy: Invalid
config data
pnacUmiPhyPortDestroy: Failed to
destroy the port
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
Invalid config data
ERROR
Facility: Kernel
Log Message
DNAT: multiple ranges no longer
supported
DNAT: Target size %u wrong for %u
ranges,
Severity
Log Message
Severity
DEBUG
%s: %s%s:%d -> %s:%d %s,
DEBUG
DEBUG
DEBUG
DNAT: wrong table %s, tablename
DNAT: hook mask 0x%x bad,
hook_mask
%s%d: resetting MPPC/MPPE
compressor,
DEBUG
%s: %s%s:%d %s,
%s: Failed to add WDS MAC: %s, dev>name,
%s: Device already has WDS mac
address attached,
%s: Added WDS MAC: %s, dev>name,
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
%s: WDS MAC address %s is not
known by this interface,
[madwifi] %s() : Not enough space.,
__FUNCTION__
Returning to chan %d, ieeeChan
WEP
AES
DEBUG
AES_CCM
DEBUG
DEBUG
CKIP
DEBUG
DEBUG
TKIP
DEBUG
PPPIOCDETACH file->f_count=%d,
PPP: outbound frame not passed
PPP: VJ decompression error
DEBUG
DEBUG
DEBUG
%s: cannot map channel to mode; freq
%u flags 0x%x,
%s: %s, vap->iv_dev->name, buf
%s: [%s] %s, vap->iv_dev->name,
DEBUG
DEBUG
DEBUG
PPP: inbound frame not passed
DEBUG
PPP: reconstructed packet
DEBUG
PPP: no memory for
DEBUG
missed pkts %u..%u,
%s%d: resetting MPPC/MPPE
compressor,
DEBUG
%s%d: wrong offset value: %d,
%s%d: wrong length of match value:
%d,
%s%d: too big offset value: %d,
%s%d: cannot decode offset value,
%s%d: wrong length code: 0x%X,
%s%d: short packet (len=%d),
__FUNCTION__,
%s%d: bad sequence number: %d,
expected: %d,
DEBUG
%s%d: wrong offset value: %d,
%s%d: wrong length of match value:
%d,
%s%d: too big offset value: %d,
%s%d: cannot decode offset value,
%s%d: wrong length code: 0x%X,
%s%d: short packet (len=%d),
__FUNCTION__,
%s%d: bad sequence number: %d,
expected: %d,
%s%d: bad sequence number: %d,
expected: %d,
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
%s: [%s] %s, vap->iv_dev->name,
ether_sprintf(mac), buf
[%s:%s] discard %s frame, %s, vap>iv_dev->name,
[%s:%s] discard frame, %s, vap>iv_dev->name,
[%s:%s] discard %s information
element, %s,
[%s:%s] discard information element,
%s,
[%s:%s] discard %s frame, %s, vap>iv_dev->name,
[%s:%s] discard frame, %s, vap>iv_dev->name,
ifmedia_add: null ifm
Adding entry for
ifmedia_set: no match for 0x%x/0x%x,
DEBUG
ifmedia_set: target
DEBUG
DEBUG
ifmedia_set: setting to
DEBUG
DEBUG
192
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Unified Services Router
User Manual
%s%d: bad sequence number: %d,
expected: %d,
DEBUG
PPPIOCDETACH file->f_count=%d,
PPP: outbound frame not passed
PPP: VJ decompression error
PPP: inbound frame not passed
PPP: reconstructed packet
PPP: no memory for
missed pkts %u..%u,
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
ifmedia_ioctl: no media found for 0x%x,
ifmedia_ioctl: switching %s to , dev>name
ifmedia_match: multiple match for

desc->ifmt_string
mode %s, desc->ifmt_string

%s, desc->ifmt_string
%s: INC_USE_COUNT, now %d,
__FUNCTION__, mod_use_count \
DEBUG
%s%s, seen_option++ ? , : ,
DEBUG
%s: DEC_USE_COUNT, now %d,
__FUNCTION__, mod_use_count \
PPPOL2TP %s: _fmt,
PPPOL2TP: --> %s, __FUNCTION__)
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
PPPOL2TP: <-- %s, __FUNCTION__)
DEBUG
%s: recv: , tunnel->name
DEBUG
%s: xmit:, session->name
DEBUG
%s: xmit:, session->name
DEBUG
%s%s, seen_option++ ? , : ,
%s, seen_option ? > :
%s: %s, dev->name, buf
%s: no memory for sysctl table!,
__func__
%s: no memory for VAP name!,
__func__
%s: failed to register sysctls!, vap>iv_dev->name
%s: no memory for new proc entry
(%s)!, __func__,
%s: module use_count is %d,
__FUNCTION__, mod_use_count
PPPOL2TP %s: _fmt,
PPPOL2TP: --> %s, __FUNCTION__)
PPPOL2TP: <-- %s, __FUNCTION__)
%s: recv: , tunnel->name
%s: xmit:, session->name
%s: xmit:, session->name
PPPOL2TP %s: _fmt,
PPPOL2TP: --> %s, __FUNCTION__)
PPPOL2TP: <-- %s, __FUNCTION__)
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
%s: 0x%p len %u, tag, p, len
%03d:, i
%02x, ((u_int8_t *)p)[i]
first difference at byte %u, i
%s: , t->name
FAIL: ieee80211_crypto_newkey failed
FAIL: ieee80211_crypto_setkey failed
FAIL: unable to allocate skbuff
FAIL: wep decap failed
FAIL: decap botch; length mismatch
FAIL: decap botch; data does not
compare
FAIL: wep encap failed
FAIL: encap data length mismatch
FAIL: encrypt data does not compare
PASS
DEBUG
%u of %u 802.11i WEP test vectors
passed, pass, total
DEBUG
DEBUG
%s: 0x%p len %u, tag, p, len
DEBUG
DEBUG
%03d:, i
DEBUG
%s: recv: , tunnel->name
%s: xmit:, session->name
%s: xmit:, session->name
IRQ 31 is triggered
[%s:%d] , __func__, __LINE__\
\t[R%s %#0x %#0x 0x%08x%08x],
(status == ERROR ? # : ), page, addr,
(uint32_t)(*pValue >> 32),
(uint32_t)(*pValue & 0xffffffff)
\t[W%s %#0x %#0x 0x%08x%08x],
(status == ERROR ? # : ), page, addr,
(uint32_t)(value >> 32), (uint32_t)(value
& 0xffffffff)
%s: mac_add
%02X:%02X:%02X:%02X:%02X:%02X,
dev->name, addr[0], addr[1], addr[2],
addr[3], addr[4], addr[5]
193
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Unified Services Router
%s: mac_del
%02X:%02X:%02X:%02X:%02X:%02X,
dev->name, addr[0], addr[1], addr[2],
addr[3], addr[4], addr[5]
%s: mac_kick
%02X:%02X:%02X:%02X:%02X:%02X,
dev->name, addr[0], addr[1], addr[2],
addr[3], addr[4], addr[5]
%s: mac_undefined
%02X:%02X:%02X:%02X:%02X:%02X,
dev->name, addr[0], addr[1], addr[2],
addr[3], addr[4], addr[5]
%s: addr_add
%02X:%02X:%02X:%02X:%02X:%02X,
dev->name, addr[0], addr[1], addr[2],
addr[3], addr[4], addr[5]
%s: addr_del
%02X:%02X:%02X:%02X:%02X:%02X,
dev->name, addr[0], addr[1], addr[2],
addr[3], addr[4], addr[5]
%s: mac_undefined
%02X:%02X:%02X:%02X:%02X:%02X,
dev->name, addr[0], addr[1], addr[2],
addr[3], addr[4], addr[5]
%s: set_float %d;%d,
IRQ 32 is triggered
ip_finish_output2: No header cache and
no neighbour!
a guy asks for address mask. Who is it?
icmp v4 hw csum failure)
User Manual
DEBUG
%02x, ((u_int8_t *)p)[i]
DEBUG
DEBUG
first difference at byte %u, i
DEBUG
DEBUG
%s: , t->name
DEBUG
DEBUG
FAIL: ieee80211_crypto_newkey failed
DEBUG
DEBUG
FAIL: ieee80211_crypto_setkey failed
DEBUG
DEBUG
DEBUG
DEBUG
FAIL: unable to allocate skbuff
FAIL: ccmp encap failed
FAIL: encap data length mismatch
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
expire>> %u %d %d %d, expire,
expire++ %u %d %d %d, expire,
DEBUG
DEBUG
FAIL: encrypt data does not compare
FAIL: ccmp decap failed
FAIL: decap botch; length mismatch
FAIL: decap botch; data does not
compare
PASS
rt_cache @%02x: %u.%u.%u.%u, hash,
rt_bind_peer(0) @%p,
NET_CALLER(iph)
ip_rt_advice: redirect to
ip_rt_bug: %u.%u.%u.%u ->
%u.%u.%u.%u, %s,
udp cork app bug 2)
udp cork app bug 3)
udp v4 hw csum failure.)
UDP: short packet: From
%u.%u.%u.%u:%u %d/%d to
%u.%u.%u.%u:%u,
UDP: bad checksum. From
%d.%d.%d.%d:%d to
%d.%d.%d.%d:%d ulen %d,
%s: lookup policy [list] found=%s,
%s: called: [output START],
__FUNCTION__
DEBUG
%u of %u 802.11i AES-CCMP test
vectors passed, pass, total
DEBUG
DEBUG
DEBUG
%s: 0x%p len %u, tag, p, len
%03d:, i
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
%02x, ((u_int8_t *)p)[i]
first difference at byte %u, i
ieee80211_crypto_newkey failed
ieee80211_crypto_setkey failed
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
unable to allocate skbuff
DEBUG
DEBUG
DEBUG
tkip enmic failed
enmic botch; length mismatch
DEBUG
DEBUG
DEBUG
enmic botch
DEBUG
%s: flow dst=%s, __FUNCTION__,
XFRMSTRADDR(fl->fl4_dst, family)
DEBUG
tkip encap failed
DEBUG
%s: flow src=%s, __FUNCTION__,
XFRMSTRADDR(fl->fl4_src, family)
DEBUG
encrypt phase1 botch
DEBUG
194
DEBUG
DEBUG
Unified Services Router
%s: flow dst=%s, __FUNCTION__,
XFRMSTRADDR(fl->fl6_dst, family)
%s: flow src=%s, __FUNCTION__,
XFRMSTRADDR(fl->fl6_src, family)
a guy asks for address mask. Who is it?
icmp v4 hw csum failure)
expire>> %u %d %d %d, expire,
expire++ %u %d %d %d, expire,
rt_cache @%02x: %u.%u.%u.%u, hash,
rt_bind_peer(0) @%p,
NET_CALLER(iph)
ip_rt_advice: redirect to
ip_rt_bug: %u.%u.%u.%u ->
%u.%u.%u.%u, %s,
UDP: short packet: From
%u.%u.%u.%u:%u %d/%d to
%u.%u.%u.%u:%u,
UDP: bad checksum. From
%d.%d.%d.%d:%d to
%d.%d.%d.%d:%d ulen %d,
a guy asks for address mask. Who is it?
fib_add_ifaddr: bug: prim == NULL
User Manual
DEBUG
encrypt data length mismatch
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
encrypt data does not compare
tkip decap failed
decrypt phase1 botch
decrypt data does not compare
decap botch; length mismatch
decap botch; data does not compare
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
tkip demic failed
802.11i TKIP test vectors passed
DEBUG
DEBUG
DEBUG
%s, buf
DEBUG
DEBUG
Atheros HAL assertion failure: %s: line
%u: %s,
DEBUG
DEBUG
DEBUG
DEBUG
fib_del_ifaddr: bug: prim == NULL
expire>> %u %d %d %d, expire,
DEBUG
DEBUG
expire++ %u %d %d %d, expire,
rt_cache @%02x: %u.%u.%u.%u, hash,
DEBUG
DEBUG
rt_bind_peer(0) @%p,
ip_rt_advice: redirect to
ip_rt_bug: %u.%u.%u.%u ->
%u.%u.%u.%u, %s,
%s: lookup policy [list] found=%s,
%s: called: [output START],
__FUNCTION__
DEBUG
DEBUG
%s: flow dst=%s, __FUNCTION__,
XFRMSTRADDR(fl->fl4_dst, family)
DEBUG
DEBUG
ath_hal: logging to %s %s,
ath_hal_logfile,
ath_hal: logging disabled
%s%s, sep, ath_hal_buildopts[i]
ath_pci: No devices found, driver not
installed.
_fmt, __VA_ARGS__
%s: Warning, using only %u entries in
%u key cache,
%s: TX99 support enabled, dev->name
%s:grppoll Buf allocation failed
,__func__
%s: %s: unable to start recv logic,
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
%s: %s: unable to start recv logic,
%s: no skbuff, __func__
%s: hardware error; resetting, dev>name
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
%s: rx FIFO overrun; resetting, dev>name
%s: flow src=%s, __FUNCTION__,
XFRMSTRADDR(fl->fl4_src, family)
DEBUG
%s: unable to reset hardware: '%s'
(HAL status %u)
DEBUG
%s: flow dst=%s, __FUNCTION__,
XFRMSTRADDR(fl->fl6_dst, family)
DEBUG
%s: unable to start recv logic, dev>name
DEBUG
%s: flow src=%s, __FUNCTION__,
XFRMSTRADDR(fl->fl6_src, family)
a guy asks for address mask. Who is it?
icmp v4 hw csum failure)
DEBUG
DEBUG
DEBUG
expire>> %u %d %d %d, expire,
expire++ %u %d %d %d, expire,
rt_cache @%02x: %u.%u.%u.%u, hash,
rt_bind_peer(0) @%p,
NET_CALLER(iph)
ip_rt_advice: redirect to
DEBUG
DEBUG
DEBUG
%s: %s: unable to reset hardware: '%s'
(HAL status %u),
%s: %s: unable to start recv logic,
ath_mgtstart: discard, no xmit buf
%s: [%02u] %-7s , tag, ix, ciphers[hk>kv_type]
%02x, hk->kv_val[i]
mac %s, ether_sprintf(mac)
DEBUG
DEBUG
%s , sc->sc_splitmic ? mic : rxmic
%02x, hk->kv_mic[i]
195
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Unified Services Router
ip_rt_bug: %u.%u.%u.%u ->
%u.%u.%u.%u, %s,
UDP: short packet: From
%u.%u.%u.%u:%u %d/%d to
%u.%u.%u.%u:%u,
UDP: bad checksum. From
%d.%d.%d.%d:%d to
%d.%d.%d.%d:%d ulen %d,
REJECT: ECHOREPLY no longer
supported.
ipt_rpc: only valid for PRE_ROUTING,
FORWARD, POST_ROUTING,
LOCAL_IN and/or LOCAL_OUT targets.
User Manual
DEBUG
txmic
DEBUG
DEBUG
%02x, hk->kv_txmic[i]
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
move data from NORMAL to XR
moved %d buffers from NORMAL to
XR, index
move buffers from XR to NORMAL
moved %d buffers from XR to
NORMAL, count
%s:%d %s, __FILE__, __LINE__,
__func__
%s:%d %s, __FILE__, __LINE__,
__func__
%s: no buffer (%s), dev->name,
__func__
%s: no skbuff (%s), dev->name,
__func__
%s: HAL qnum %u out of range, max
%u!,
grppoll_start: grppoll Buf allocation
failed
%s: HAL qnum %u out of range, max
%u!,
DEBUG
%s: AC %u out of range, max %u!,
DEBUG
DEBUG
%s: unable to update hardware queue
%s: bogus frame type 0x%x (%s), dev>name,
DEBUG
ath_stoprecv: rx queue 0x%x, link %p,
%s: %s: unable to reset channel %u
(%u MHz)
DEBUG
%s: %s: unable to restart recv logic,
%s: unable to allocate channel table,
dev->name
%s: unable to allocate channel table,
dev->name
%s: unable to collect channel list from
HAL;
R (%p %llx) %08x %08x %08x %08x
%08x %08x %c,
DEBUG
ip_nat_init: can't setup rules.
ip_nat_init: can't register in hook.
DEBUG
DEBUG
ip_nat_init: can't register out hook.
DEBUG
ip_nat_init: can't register adjust in hook.
ip_nat_init: can't register adjust out
hook.
DEBUG
ip_nat_init: can't register local out hook.
DEBUG
ip_nat_init: can't register local in hook.
DEBUG
ipt_hook: happy cracking.
ip_conntrack: can't register pre-routing
defrag hook.
ip_conntrack: can't register local_out
defrag hook.
ip_conntrack: can't register pre-routing
hook.
ip_conntrack: can't register local out
hook.
ip_conntrack: can't register local in
helper hook.
ip_conntrack: can't register postrouting
helper hook.
ip_conntrack: can't register post-routing
hook.
ip_conntrack: can't register local in
hook.
DEBUG
ip_conntrack: can't register to sysctl.
ip_conntrack_rtsp v
IP_NF_RTSP_VERSION loading
ip_conntrack_rtsp: max_outstanding
must be a positive integer
ip_conntrack_rtsp: setup_timeout must
be a positive integer
DEBUG
ip_conntrack_rtsp: ERROR registering
port %d, ports[i]
ip_nat_rtsp v IP_NF_RTSP_VERSION
loading
%s: Sorry! Cannot find this match
option., __FILE__
%s: unable to update h/w beacon
queue parameters,
%s: stuck beacon; resetting (bmiss
count %u),
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
T (%p %llx) %08x %08x %08x %08x
%08x %08x %08x %08x %c,
%s: no memory for sysctl table!,
__func__
%s: no memory for device name
storage!, __func__
196
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Unified Services Router
User Manual
%s: failed to register sysctls!, sc>sc_dev->name
%s: mac %d.%d phy %d.%d, dev>name,
5 GHz radio %d.%d 2 GHz radio
%d.%d,
radio %d.%d, ah->ah_analog5GhzRev
>> 4,
radio %d.%d, ah->ah_analog5GhzRev
>> 4,
ipt_time loading
DEBUG
ipt_time unloaded
ip_conntrack_irc: max_dcc_channels
must be a positive integer
ip_conntrack_irc: ERROR registering
port %d,
ip_nat_h323:
ip_nat_mangle_tcp_packet
ip_nat_h323:
ip_nat_mangle_udp_packet
DEBUG
ip_nat_h323: out of expectations
DEBUG
ip_nat_h323: out of RTP ports
DEBUG
ip_nat_h323: out of TCP ports
DEBUG
ip_nat_q931: out of TCP ports
DEBUG
ip_nat_ras: out of TCP ports
ip_nat_q931: out of TCP ports
ip_conntrack_core: Frag of proto %u.,
DEBUG
DEBUG
DEBUG
Broadcast packet!
DEBUG
Should bcast: %u.%u.%u.%u>%u.%u.%u.%u (sk=%p, ptype=%u),
DEBUG
ip_conntrack version %s (%u buckets,
%d max)
ERROR registering port %d,
netfilter PSD loaded - (c) astaro AG
netfilter PSD unloaded - (c) astaro AG
%s , SELF
%s , LAN
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
xlr8NatSoftCtxEnqueue: Calling
xlr8NatIpFinishOutput () .., status
xlr8NatSoftCtxEnqueue:
xlr8NatIpFinishOutput () returned [%d],
status
icmpExceptionHandler: Exception!
fragExceptionHandler: Exception!
algExceptionHandler: Exception!
dnsExceptionHandler: Exception!
IPsecExceptionHandler: Exception!
%s , WAN
DEBUG
ESP Packet Src:%x Dest:%x Sport:%d
dport:%d secure:%d spi:%d isr:%p,
DEBUG
DEBUG
DEBUG
DEBUG
%s: Use hw queue %u for %s traffic,
%s: Use hw queue %u for CAB traffic,
dev->name,
%s: Use hw queue %u for beacons,
dev->name,
Could not find Board Configuration
Data
Could not find Radio Configuration
data
ath_ahb: No devices found, driver not
installed.
_fmt, __VA_ARGS__
_fmt, __VA_ARGS__
xlr8NatIpFinishOutput: Err.. skb2 ==
NULL !
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
TRUNCATED
SRC=%u.%u.%u.%u
DST=%u.%u.%u.%u ,
LEN=%u TOS=0x%02X
PREC=0x%02X TTL=%u ID=%u ,
FRAG:%u , ntohs(ih->frag_off) &
IP_OFFSET
DEBUG
TRUNCATED
DEBUG
PROTO=TCP
DEBUG
xlr8NatConntrackPreHook: We found
the valid context,
xlr8NatConntrackPreHook: Not a
secured packet.
xlr8NatConntrackPreHook: isr=[%p],
pIsr
xlr8NatConntrackPreHook:
secure=[%d], secure
Context found for ESP %p,pFlowEntry>post.pIsr[0]
xlr8NatConntrackPreHook: New
connection.
INCOMPLETE [%u bytes] ,
DEBUG
xlr8NatConntrackPostHook:
postSecure=[%d] postIsr=[%p %p],
DEBUG
DEBUG
DEBUG
proto %d spi %d <-------> proto %d spi
%d,pPktInfo->proto,pPktInfo->spi,
IPSEC_INF Clock skew detected
DEBUG
DEBUG
SPT=%u DPT=%u ,
SEQ=%u ACK=%u ,
DEBUG
DEBUG
DEBUG
197
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Unified Services Router
User Manual
WINDOW=%u , ntohs(th->window)
RES=0x%02x ,
(u8)(ntohl(tcp_flag_word(th) &
TCP_RESERVED_BITS) >> 22)
URGP=%u , ntohs(th->urg_ptr)
DEBUG
TRUNCATED
DEBUG
%02X, op[i]
DEBUG
PROTO=UDP
DEBUG
INCOMPLETE [%u bytes] ,
DEBUG
SPT=%u DPT=%u LEN=%u ,
DEBUG
SPT=%u DPT=%u LEN=%u ,
PROTO=ICMP
DEBUG
DEBUG
INCOMPLETE [%u bytes] ,
TYPE=%u CODE=%u , ich->type, ich>code
DEBUG
INCOMPLETE [%u bytes] ,
DEBUG
ID=%u SEQ=%u ,
DEBUG
PARAMETER=%u ,
DEBUG
GATEWAY=%u.%u.%u.%u ,
DEBUG
MTU=%u , ntohs(ich->un.frag.mtu)
DEBUG
PROTO=AH
INCOMPLETE [%u bytes] ,
DEBUG
DEBUG
SPI=0x%x , ntohl(ah->spi)
PROTO=ESP
DEBUG
DEBUG
INCOMPLETE [%u bytes] ,
SPI=0x%x , ntohl(eh->spi)
DEBUG
DEBUG
PROTO=%u , ih->protocol
UID=%u , skb->sk->sk_socket->file>f_uid
<%d>%sIN=%s OUT=%s , loginfo>u.log.level,
level_string
DEBUG
%sIN=%s OUT=%s ,
%s , prefix == NULL ? loginfo->prefix :
prefix
DEBUG
IN=
OUT=
PHYSIN=%s , physindev->name
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
IPSEC_ERR [%s:%d]: Max (%d) No of
SA Limit reached,
IPSEC_ERR [%s:%d]: Max (%d) No of
SA Limit reached,
IPSEC_ERR [%s:%d]: time(secs): %u
ERROR: Failed to add entry to IPsec
sa table
ERROR: Failed to add entry to IPsec
sa table
ERROR: Failed to add entry to IPsec
sa table
ERROR: Failed to add entry to IPsec
sa table
ERROR: Failed to add entry to IPsec
sa table
ERROR: Failed to add entry to IPsec
sa table
unknown oid '%s', varName
could not find oid pointer for '%s',
varName
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
unRegistering IPsecMib .....
ERROR: Failed to add entry to IPsec
sa table
ERROR: Failed to add entry to IPsec
sa table
ERROR: Failed to add entry to IPsec
sa table
ERROR: Failed to add entry to IPsec
sa table
ERROR: Failed to add entry to IPsec
sa table
ERROR: Failed to add entry to IPsec
sa table
unknown oid '%s', varName
could not find oid pointer for '%s',
varName
unRegistering IPsecMib .....
. %u.%u.%u.%u, NIPQUAD(trt>rt_dst)
%02x, *p
. %u.%u.%u.%u, NIPQUAD(trt>rt_dst)
DEBUG
%02x, *p
. %u.%u.%u.%u, NIPQUAD(trt>rt_dst)
%02x, *p
. %u.%u.%u.%u, NIPQUAD(trt>rt_dst)
DEBUG
%02x, *p
unable to register vIPsec kernel comp
to UMI
unregistering VIPSECK from UMI ....
in vIPsecKIoctlHandler cmd - %d, cmd
DEBUG
198
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Unified Services Router
User Manual
PHYSOUT=%s , physoutdev->name
DEBUG
MAC=
DEBUG
%02x%c, *p,
DEBUG
NAT: no longer support implicit source
local NAT
NAT: packet src %u.%u.%u.%u -> dst
%u.%u.%u.%u,
SNAT: multiple ranges no longer
supported
format,##args)
DEBUG
DEBUG
DEBUG
DEBUG
version
offset_before=%d, offset_after=%d,
correction_pos=%u, x->offset_before, x>offset_after, x->correction_pos
DEBUG
ip_ct_h323:
DEBUG
DEBUG
%s: Error. DST Refcount value less
than 1 (%d),
for %s DEVICE refcnt: %d ,pDst>dev->name,
%s: Got Null m:%p *m:%p sa:%p
*sa:%p,__func__,ppBufMgr,
%s Got Deleted SA:%p
state:%d,__func__,pIPsecInfo,pIPsecIn
fo->state
%s: %s: fmt, __FILE__,
__FUNCTION__ , ## args)
%s: %s: fmt, __FILE__,
__FUNCTION__ , ## args)
ipt_TIME: format, ## args)
IPT_ACCOUNT_NAME : checkentry()
wrong parameters (not equals existing
table parameters).
IPT_ACCOUNT_NAME : checkentry()
too big netmask.
IPT_ACCOUNT_NAME : checkentry()
failed to allocate %zu for new table
%s., sizeof(struct t_ipt_account_table),
info->name
DEBUG
DEBUG
DEBUG
DEBUG
INFO
INFO
INFO
INFO
INFO
INFO
ip_ct_h323: incomplete TPKT
(fragmented?)
DEBUG
ip_ct_h245: decoding error: %s,
DEBUG
IPT_ACCOUNT_NAME : checkentry()
wrong network/netmask.
account: Wrong netmask given by
netmask parameter (%i). Valid is 32 to
0., netmask
DEBUG
IPT_ACCOUNT_NAME : checkentry()
failed to create procfs entry.
INFO
ip_ct_q931: decoding error: %s,
ip_ct_q931: packet dropped
DEBUG
DEBUG
IPT_ACCOUNT_NAME : checkentry()
failed to register match.
failed to create procfs entry .
INFO
INFO
ip_ct_ras: decoding error: %s,
DEBUG
MPPE/MPPC encryption/compression
module registered
INFO
ip_ct_ras: packet dropped
DEBUG
ERROR registering port %d,
DEBUG
MPPE/MPPC encryption/compression
module unregistered
PPP generic driver version
PPP_VERSION
DEBUG
MPPE/MPPC encryption/compression
module registered
INFO
DEBUG
MPPE/MPPC encryption/compression
module unregistered
INFO
DEBUG
DEBUG
DEBUG
PPP generic driver version
PPP_VERSION
PPPoL2TP kernel driver, %s,
PPPoL2TP kernel driver, %s,
INFO
INFO
INFO
DEBUG
DEBUG
DEBUG
DEBUG
PPPoL2TP kernel driver, %s,
failed to create procfs entry .
proc dir not created ..
Initialzing Product Data modules
INFO
INFO
INFO
INFO
ip_ct_h245: packet dropped
ERROR registering port %d,
ipt_connlimit [%d]:
src=%u.%u.%u.%u:%d
dst=%u.%u.%u.%u:%d %s,
ipt_connlimit [%d]:
src=%u.%u.%u.%u:%d
dst=%u.%u.%u.%u:%d new,
ipt_connlimit: Oops: invalid ct state ?
ipt_connlimit: Hmm, kmalloc failed :-(
ipt_connlimit: src=%u.%u.%u.%u
mask=%u.%u.%u.%u
_lvl PPPOL2TP: _fmt, ##args
%02X, ptr[length]
%02X, ((unsigned char *) m-
199
INFO
INFO
INFO
INFO
Unified Services Router
User Manual
>msg_iov[i].iov_base)[j]
%02X, skb->data[i]
_lvl PPPOL2TP: _fmt, ##args
%02X, ptr[length]
%02X, ((unsigned char *) m>msg_iov[i].iov_base)[j]
%02X, skb->data[i]
_lvl PPPOL2TP: _fmt, ##args
%02X, ptr[length]
%02X, ((unsigned char *) m>msg_iov[i].iov_base)[j]
DEBUG
DEBUG
DEBUG
De initializing by \
kernel UMI module loaded
kernel UMI module unloaded
INFO
INFO
INFO
DEBUG
DEBUG
DEBUG
DEBUG
Loading bridge module
Unloading bridge module
unsupported command %d, cmd
Loading ifDev module
INFO
INFO
INFO
INFO
DEBUG
INFO
%02X, skb->data[i]
KERN_EMERG THE value read is
%d,value*/
KERN_EMERG Factory Reset button is
pressed
DEBUG
Unloading ifDev module
ERROR#%d in alloc_chrdev_region,
result
DEBUG
ERROR#%d in cdev_add, result
INFO
DEBUG
using bcm switch %s, bcmswitch
INFO
DEBUG
privlegedID %d wanporttNo: %d,
privlegedID,wanportNo
INFO
DEBUG
Loading mii
INFO
DEBUG
Unloading mii
INFO
DEBUG
DEBUG
%s: Version 0.1
%s: driver unloaded, dev_info
wlan: %s backend registered, be>iab_name
wlan: %s backend unregistered,
wlan: %s acl policy registered, iac>iac_name
wlan: %s acl policy unregistered, iac>iac_name
%s, tmpbuf
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
KERN_EMERG Returing error in INTR
registration
KERN_EMERG Initialzing Factory
defaults modules
Failed to allocate memory for
pSipListNode
SIPALG: Memeory allocation failed for
pSipNodeEntryTbl
pkt-err %s, pktInfo.error
pkt-err %s, pktInfo.error
pkt-err %s, pktInfo.error
DEBUG
DEBUG
%s Len=%d, msg, len
DEBUG
%02x , ((uint8_t *) ptr)[i]
End
CVM_MOD_EXP_BASE MISMATCH
cmd=%x base=%x, cmd,
op->sizeofptr = %ld, op->sizeofptr
opcode cmd = %x, cmd
modexp opcode received
Memory Allocation failed
modexpcrt opcode received
kmalloc failed
kmalloc failed
DEBUG
DEBUG
kmalloc failed
kmalloc failed
kmalloc Failed
kmalloc failed
unknown cyrpto ioctl cmd received %x,
cmd
register_chrdev returned ZERO
const char *descr, krb5_keyblock *k) {
F password, &pdata
DEBUG
DEBUG
DEBUG
DEBUG
VLAN2
VLAN3
VLAN4 <%d %d>,
%s: %s, dev_info, version
%s: driver unloaded, dev_info
%s, buf
%s: %s (, dev_info, ath_hal_version
%s: driver unloaded, dev_info
%s: %s: mem=0x%lx, irq=%d
hw_base=0x%p,
%s: %s, dev_info, version
%s: driver unloaded, dev_info
%s: %s: mem=0x%lx, irq=%d,
DEBUG
DEBUG
DEBUG
DEBUG
%s: %s: mem=0x%lx, irq=%d,
%s: %s, dev_info, version
%s: driver unloaded, dev_info
%s, buf
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
200
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
Unified Services Router
User Manual
test key, key
pre-hashed key, key
const char *descr, krb5_keyblock *k) {
AES 128-bit key, &key
const char *descr, krb5_keyblock *k) {
test key, key
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
pre-hashed key, key
const char *descr, krb5_keyblock *k) {
DEBUG
DEBUG
128-bit AES key,&dk
DEBUG
256-bit AES key, &dk
WARNING:
bwMonMultipathNxtHopSelect::
checking rates
hop :%d dev:%s usableBwLimit = %d
currBwShare = %d lastHopSelected =
%d weightedHopPrefer = %d ,
1. selecting hop: %d lastHopSelected =
%d , selHop, lastHopSelected
4. hop :%d dev:%s usableBwLimit = %d
currBwShare = %d lastHopSelected =
%d weightedHopPrefer = %d ,
2. selecting hop: %d lastHopSelected =
%d , selHop, lastHopSelected
3. selecting hop: %d lastHopSelected =
%d , selHop, lastHopSelected
bwMonitor multipath selection enabled
bwMonitor multipath selection disabled
weightedHopPrefer set to %d
,weightedHopPrefer
bwMonitor sysctl registration failed
bwMonitor sysctl registered
bwMonitor sysctl not registered
Unregistered bwMonitor sysctl
CONFIG_SYSCTL enabled ...
Initialized bandwidth monitor ...
Removed bandwidth monitor ...
Oops.. AES_GCM_encrypt failed
(keylen:%u),key->cvm_keylen
Oops.. AES_GCM_decrypt failed
(keylen:%u),key->cvm_keylen
%s, msg
%02x%s, data[i],
INFO
INFO
INFO
INFO
INFO
INFO
DEBUG
DEBUG
%s: %s (, dev_info, ath_hal_version
%s: driver unloaded, dev_info
%s: driver unloaded, dev_info
%s: Version 2.0.0
%s: driver unloaded, dev_info
%s: driver unloaded, dev_info
wlan: %s backend registered, be>iab_name
wlan: %s backend unregistered,
wlan: %s acl policy registered, iac>iac_name
wlan: %s acl policy unregistered, iac>iac_name
%s: %s, dev_info, version
DEBUG
%s: driver unloaded, dev_info
INFO
DEBUG
%s: %s (, dev_info, ath_hal_version
INFO
DEBUG
%s: driver unloaded, dev_info
INFO
DEBUG
%s: %s: mem=0x%lx, irq=%d,
INFO
DEBUG
%s: %s, dev_info, version
INFO
DEBUG
DEBUG
DEBUG
%s: driver unloaded, dev_info
ath_pci: switching rfkill capability %s,
Unknown autocreate mode: %s,
INFO
INFO
INFO
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
%s: %s: mem=0x%lx, irq=%d,
%s: %s, dev_info, version
%s: driver unloaded, dev_info
%s: %s, dev_info, version
%s: unloaded, dev_info
%s: %s, dev_info, version
%s: unloaded, dev_info
%s: %s, dev_info, version
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
DEBUG
%s: unloaded, dev_info
INFO
DEBUG
DEBUG
DEBUG
failed to create procfs entry .
ICMP: %u.%u.%u.%u:
ICMP: %u.%u.%u.%u: Source
Wrong address mask %u.%u.%u.%u
from
Redirect from %u.%u.%u.%u on %s
about
INFO
INFO
INFO
Failed to set AES encrypt key
DEBUG
Failed to set AES encrypt key
DEBUG
AES %s Encrypt Test Duration: %d:%d,
hard ? Hard : Soft,
DEBUG
Failed to set AES encrypt key
DEBUG
IP: routing cache hash table of %u
buckets, %ldKbytes,
source route option %u.%u.%u.%u ->
%u.%u.%u.%u,
201
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
Unified Services Router
User Manual
Failed to set AES encrypt key
AES %s Decrypt Test Duration: %d:%d,
hard ? Hard : Soft,
DEBUG
ICMP: %u.%u.%u.%u:
INFO
DEBUG
INFO
Failed to set AES encrypt key
DEBUG
Failed to set AES encrypt key
DEBUG
ICMP: %u.%u.%u.%u: Source
Wrong address mask %u.%u.%u.%u
from
Redirect from %u.%u.%u.%u on %s
about
Failed to set AES encrypt key
DEBUG
Failed to set AES encrypt key
DEBUG
Failed to set DES encrypt key[%d], i
DEBUG
Failed to set DES decrypt key[%d], i
Failed to set DES encrypt key[%d], i
Failed to set DES decrypt key[%d], i
Failed to set DES encrypt key
DEBUG
DEBUG
DEBUG
DEBUG
Failed to set DES decrypt key
DEBUG
Failed to set DES encrypt key
DEBUG
IP: routing cache hash table of %u
buckets, %ldKbytes,
source route option %u.%u.%u.%u ->
%u.%u.%u.%u,
Wrong address mask %u.%u.%u.%u
from
Redirect from %u.%u.%u.%u on %s
about
source route option
ICMP: %u.%u.%u.%u:
ICMP: %u.%u.%u.%u: Source
Wrong address mask %u.%u.%u.%u
from
Redirect from %u.%u.%u.%u on %s
about
DEBUG
DEBUG
IP: routing cache hash table of %u
buckets, %ldKbytes,
source route option %u.%u.%u.%u ->
%u.%u.%u.%u,
IPsec: device unregistering: %s, dev>name
IPsec: device down: %s, dev->name
DEBUG
mark: only supports 32bit mark
3DES Software Test:
3DES Software Test %s,
des3SoftTest(0) ? Failed : Passed
DEBUG
ipt_time: invalid argument
DEBUG
ipt_time: IPT_DAY didn't matched
3DES Hardware Test:
3DES Hardware Test %s,
des3HardTest(0) ? Failed : Passed
DEBUG
./Logs_kernel.txt:45:KERN_WARNING
DEBUG
DES Software Test:
DES Software Test %s, desSoftTest(0)
? Failed : Passed
DEBUG
DES Hardware Test:
DES Hardware Test %s,
desHardTest(0) ? Failed : Passed
DEBUG
./Logs_kernel.txt:59:KERN_WARNING
ipt_LOG: not logging via system
console
%s: wrong options length: %u, fname,
opt_len
%s: options rejected: o[0]=%02x,
o[1]=%02x,
SHA Software Test:
SHA Software Test %s, shaSoftTest(0)
? Failed : Passed
DEBUG
SHA Hardware Test:
SHA Hardware Test %s,
shaHardTest(0) ? Failed : Passed
DEBUG
DEBUG
%s: don't know what to do: o[5]=%02x,
%s: wrong options length: %u, fname,
opt_len
%s: options rejected: o[0]=%02x,
o[1]=%02x,
MD5 Software Test:
DEBUG
%s: wrong options length: %u,
Failed to set DES decrypt key
DEBUG
AES Software Test:
AES Software Test %s, aesSoftTest(0)
? Failed : Passed
AES Hardware Test:
AES Hardware Test %s,
aesHardTest(0) ? Failed : Passed
DEBUG
DEBUG
DEBUG
DEBUG
%s: wrong options length: %u,
%s: options rejected: o[0]=%02x,
o[1]=%02x,
202
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
INFO
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
Unified Services Router
MD5 Software Test %s, md5SoftTest(0)
? Failed : Passed
User Manual
DEBUG
%s: options rejected: o[0]=%02x,
o[1]=%02x,
MD5 Hardware Test:
MD5 Hardware Test %s,
md5HardTest(0) ? Failed : Passed
DEBUG
DEBUG
%s: don't know what to do: o[5]=%02x,
*** New port %d ***, ntohs(expinfo>natport)
AES Software Test: %d iterations, iter
DEBUG
** skb len %d, dlen %d,(*pskb)->len,
AES Software Test Duration: %d:%d,
DEBUG
********** Non linear skb
AES Hardware Test: %d iterations, iter
DEBUG
End of sdp %p, nexthdr
AES Hardware Test Duration: %d:%d,
DEBUG
%s: unknown pairwise cipher %d,
3DES Software Test: %d iterations, iter
DEBUG
%s: unknown group cipher %d,
3DES Software Test Duration: %d:%d,
DEBUG
%s: unknown SIOCSIWAUTH flag %d,
3DES Hardware Test: %d iterations, iter
DEBUG
%s: unknown SIOCGIWAUTH flag %d,
3DES Hardware Test Duration: %d:%d,
DEBUG
%s: unknown algorithm %d,
DES Software Test: %d iterations, iter
DEBUG
%s: key size %d is too large,
DES Software Test Duration: %d:%d,
DEBUG
try_module_get failed
DES Hardware Test: %d iterations, iter
DEBUG
%s: request_irq failed, dev->name
DES Hardware Test Duration: %d:%d,
DEBUG
try_module_get failed
SHA Software Test: %d iterations, iter
DEBUG
try_module_get failed
SHA Software Test Duration: %d:%d,
DEBUG
%s: unknown pairwise cipher %d,
SHA Hardware Test: %d iterations, iter
DEBUG
%s: unknown group cipher %d,
SHA Hardware Test Duration: %d:%d,
DEBUG
%s: unknown SIOCSIWAUTH flag %d,
MD5 Software Test: %d iterations, iter
DEBUG
%s: unknown SIOCGIWAUTH flag %d,
MD5 Software Test Duration: %d:%d,
DEBUG
%s: unknown algorithm %d,
MD5 Hardware Test: %d iterations, iter
DEBUG
MD5 Hardware Test Duration: %d:%d,
DEBUG
%s: key size %d is too large,
unable to load %s,
scan_modnames[mode]
./pnac/src/pnac/linux/kernel/xcalibur.c:2
09:#define DEBUG_PRINTK printk
DEBUG
Failed to mkdir /proc/net/madwifi
bcmDeviceInit: registration failed
DEBUG
try_module_get failed
bcmDeviceInit: pCdev Add failed
DEBUG
REG Size == 8 Bit
Value = %x ::: At Page = %x : Addr =
%x
DEBUG
%s: request_irq failed, dev->name
too many virtual ap's (already got %d),
sc->sc_nvaps
REG Size == 16 Bit
DEBUG
DEBUG
%s: request_irq failed, dev->name
rix %u (%u) bad ratekbps %u mode
%u,
203
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
Unified Services Router
Value = %x ::: At Page = %x : Addr =
%x
REG Size == 32 Bit
Value = %x ::: At Page = %x : Addr =
%x
User Manual
DEBUG
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
DEBUG
%s: no rates for %s?,
no rates yet! mode %u, sc>sc_curmode
DEBUG
%u.%u.%u.%u sent an invalid ICMP
REG Size is not in 8/16/32/64
Written Value = %x ::: At Page = %x :
Addr = %x
DEBUG
dst cache overflow
DEBUG
Neighbour table overflow.
bcm_ioctl :Unknown Ioctl Case :
DEBUG
host %u.%u.%u.%u/if%d ignores
DEBUG
martian destination %u.%u.%u.%u
from
DEBUG
martian source %u.%u.%u.%u from
DEBUG
ll header:
DEBUG
%u.%u.%u.%u sent an invalid ICMP
DEBUG
dst cache overflow
DEBUG
Neighbour table overflow.
DEBUG
host %u.%u.%u.%u/if%d ignores
DEBUG
martian destination %u.%u.%u.%u
from
DEBUG
martian source %u.%u.%u.%u from
Cannot Set Rate: %x, value
Getting Rate Series: %x,vap>iv_fixed_rate.series
Getting Retry Series: %x,vap>iv_fixed_rate.retries
DEBUG
ll header:
DEBUG
%u.%u.%u.%u sent an invalid ICMP
DEBUG
dst cache overflow
IC Name: %s,ic->ic_dev->name
DEBUG
Neighbour table overflow.
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
usage: rtparams rt_idx <0|1> per
<0..100> probe_intval <0..100>
DEBUG
host %u.%u.%u.%u/if%d ignores
WARNIN
DEBUG
martian source %u.%u.%u.%u from
DEBUG
REG Size == 64 Bit
=========Register Dump for Port
Number # %d=========,port
%s : Read Status=%s
data=%#x,regName[j],
%s : Read Status=%s
data=%#x,regName[j],
powerDeviceInit: device registration
failed
powerDeviceInit: adding device failed
%s: Error: Big jump in pn number.
TID=%d, from %x %x to %x %x.
%s: The MIC is corrupted. Drop this
frame., __func__
%s: The MIC is OK. Still use this frame
and update PN., __func__
ADDBA send failed: recipient is not a
11n node
usage: acparams ac <0|3> RTS <0|1>
aggr scaling <0..4> min mbps <0..250>
usage: hbrparams ac <2> enable <0|1>
per_low <0..50>
DEBUG
cix %u (%u) bad ratekbps %u mode
%u,
%s(): ADDBA mode is AUTO, __func__
DEBUG
ll header:
martian destination %u.%u.%u.%u
from
%s(): Invalid TID value, __func__
DEBUG
%u.%u.%u.%u sent an invalid ICMP
%s(): ADDBA mode is AUTO, __func__
DEBUG
dst cache overflow
%s(): Invalid TID value, __func__
DEBUG
Neighbour table overflow.
%s(): Invalid TID value, __func__
Addba status IDLE
DEBUG
DEBUG
host %u.%u.%u.%u/if%d ignores
martian destination %u.%u.%u.%u
204
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
WARNIN
Unified Services Router
User Manual
from
WARNIN
WARNIN
ERROR
%s(): ADDBA mode is AUTO, __func__
DEBUG
martian source %u.%u.%u.%u from
%s(): Invalid TID value, __func__
Error in ADD- no node available
%s(): Channel capabilities do not match,
chan flags 0x%x,
%s: cannot map channel to mode; freq
%u flags 0x%x,
DEBUG
DEBUG
ll header:
Unable to create ip_set_list
DEBUG
ERROR
ic_get_currentCountry not initialized yet
Country ie is %c%c%c,
%s: wrong state transition from %d to
%d,
%s: wrong state transition from %d to
%d,
%s: wrong state transition from %d to
%d,
%s: wrong state transition from %d to
%d,
DEBUG
DEBUG
Unable to create ip_set_hash
ip_conntrack_in: Frag of proto %u
(hook=%u),
Unable to register netfilter socket
option
Unable to create ip_conntrack_hash
Unable to create ip_conntrack slab
cache
Unable to create ip_expect slab cache
Unable to create ip_set_iptreeb slab
cache
Unable to create ip_set_iptreed slab
cache
ERROR
%s: wrong state transition from %d to
%d,
%s: wrong state transition from %d to
%d,
ieee80211_deliver_l2uf: no buf available
%s: %s, vap->iv_dev->name, buf /*
NB: no */
%s: [%s] %s, vap->iv_dev->name,
%s: [%s] %s, vap->iv_dev->name,
ether_sprintf(mac), buf
[%s:%s] discard %s frame, %s, vap>iv_dev->name,
[%s:%s] discard frame, %s, vap>iv_dev->name,
[%s:%s] discard %s information
element, %s,
[%s:%s] discard information element,
%s,
[%s:%s] discard %s frame, %s, vap>iv_dev->name,
[%s:%s] discard frame, %s, vap>iv_dev->name,
HBR list
dumpNode\tAddress\t\t\tState\tTrigger\t
Block
Nodes
informationAddress\t\t\tBlock\t\tDroped
VI frames
%d\t
%2.2x:%2.2x:%2.2x:%2.2x:%2.2x:%2.2
x\t%s\t%s\t%s,
%2.2x:%2.2x:%2.2x:%2.2x:%2.2x:%2.2
x\t%s\t\t%d,
[%d]\tFunction\t%s, j, ni>node_trace[i].funcp
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
%s: cannot allocate space for
%scompressor, fname,
%s: cannot allocate space for MPPC
history,
%s: cannot allocate space for MPPC
history,
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
DEBUG
%s: cannot load ARC4 module, fname
%s: cannot load SHA1 module, fname
%s: CryptoAPI SHA1 digest size too
small, fname
%s: cannot allocate space for SHA1
digest, fname
DEBUG
%s%d: trying to write outside history
ERROR
DEBUG
%s%d: trying to write outside history
ERROR
DEBUG
ERROR
DEBUG
%s%d: trying to write outside history
%s%d: too big uncompressed packet:
%d,
%s%d: encryption negotiated but not
an
DEBUG
%s%d: error - not an MPPC or MPPE
frame
ERROR
DEBUG
Kernel doesn't provide ARC4 and/or
SHA1 algorithms
ERROR
DEBUG
PPP: not interface or channel??
ERROR
DEBUG
PPP: no memory (VJ compressor)
ERROR
DEBUG
failed to register PPP device (%d), err
ERROR
DEBUG
DEBUG
205
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
[%d]\tMacAddr\t%s, j,
[%d]\tDescp\t\t%s, j, ni>node_trace[i].descp
[%d]\tValue\t\t%llu(0x%llx), j, ni>node_trace[i].value,
ifmedia_add: null ifm
Adding entry for
ifmedia_set: no match for 0x%x/0x%x,
DEBUG
PPP: no memory (VJ comp pkt)
ERROR
DEBUG
PPP: no memory (comp pkt)
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
ERROR
ERROR
ERROR
ERROR
ifmedia_set: target
ifmedia_set: setting to
ifmedia_ioctl: switching %s to , dev>name
ifmedia_match: multiple match for
DEBUG
DEBUG

desc->ifmt_string
DEBUG
DEBUG
ppp: compressor dropped pkt
PPP: no memory (fragment)
PPP: VJ uncompressed error
ppp_decompress_frame: no memory
ppp_mp_reconstruct bad seq %u <
%u,
PPP: couldn't register device %s (%d),
ppp: destroying ppp struct %p but
dead=%d
ppp: destroying undead channel %p !,
PPP: removing module but units
remain!
PPP: failed to unregister PPP device
mode %s, desc->ifmt_string
DEBUG

DEBUG
%s, desc->ifmt_string
%s%s, seen_option++ ? , : ,
%s%s, seen_option++ ? , : ,
DEBUG
DEBUG
DEBUG
%s, seen_option ? > :
DEBUG
%s: %s, dev->name, buf
%s: no memory for sysctl table!,
__func__
%s: failed to register sysctls!, vap>iv_dev->name
Atheros HAL assertion failure: %s: line
%u: %s,
ath_hal: logging to %s %s,
ath_hal_logfile,
DEBUG
%s: cannot allocate space for
%scompressor, fname,
%s: cannot allocate space for MPPC
history,
%s: cannot allocate space for MPPC
history,
%s: cannot load ARC4 module, fname
%s: cannot load SHA1 module, fname
%s: CryptoAPI SHA1 digest size too
small, fname
%s: cannot allocate space for SHA1
digest, fname
DEBUG
%s%d: trying to write outside history
ERROR
DEBUG
%s%d: trying to write outside history
ERROR
DEBUG
ERROR
ath_hal: logging disabled
DEBUG
%s%s, sep, ath_hal_buildopts[i]
ath_pci: No devices found, driver not
installed.
DEBUG
DEBUG
%s%d: trying to write outside history
%s%d: too big uncompressed packet:
%d,
%s%d: encryption negotiated but not
an
%s%d: error - not an MPPC or MPPE
frame
Kernel doesn't provide ARC4 and/or
SHA1 algorithms
DEBUG
PPP: not interface or channel??
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
PPP: no memory (VJ compressor)
failed to register PPP device (%d), err
PPP: no memory (comp pkt)
ppp: compressor dropped pkt
ERROR
ERROR
ERROR
ERROR
DEBUG
PPP: no memory (VJ comp pkt)
ERROR
DEBUG
DEBUG
PPP: no memory (comp pkt)
PPP: no memory (fragment)
ERROR
ERROR
---:%d pri:%d qd:%u ad:%u sd:%u
tot:%u amp:%d %02x:%02x:%02x,
SC Pushbutton Notify on %s::%s,dev>name,vap->iv_dev->name
Could not find Board Configuration Data
Could not find Radio Configuration data
%s: No device, __func__
ath_ahb: No devices found, driver not
installed.
PKTLOG_TAG %s:proc_dointvec failed,
__FUNCTION__
PKTLOG_TAG %s:proc_dointvec failed,
DEBUG
DEBUG
DEBUG
206
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
__FUNCTION__
%s: failed to register sysctls!,
proc_name
PKTLOG_TAG %s: proc_mkdir failed,
__FUNCTION__
PKTLOG_TAG %s: pktlog_attach failed
for %s,
PKTLOG_TAG %s:allocation failed for
pl_info, __FUNCTION__
PKTLOG_TAG %s:allocation failed for
pl_info, __FUNCTION__
PKTLOG_TAG %s: create_proc_entry
failed for %s,
PKTLOG_TAG %s: sysctl register failed
for %s,
PKTLOG_TAG %s: page fault out of
range, __FUNCTION__
PKTLOG_TAG %s: page fault out of
range, __FUNCTION__
PKTLOG_TAG %s: Log buffer
unavailable, __FUNCTION__
PKTLOG_TAG
Logging should be disabled before
changing bufer size
%s:allocation failed for pl_info, __func__
%s: Unable to allocate buffer, __func__
%s:allocation failed for pl_info, __func__
%s: Unable to allocate buffer, __func__
Atheros HAL assertion failure: %s: line
%u: %s,
ath_hal: logging to %s %s,
ath_hal_logfile,
ath_hal: logging disabled
User Manual
DEBUG
PPP: VJ uncompressed error
ERROR
DEBUG
ppp_decompress_frame: no memory
ppp_mp_reconstruct bad seq %u <
%u,
ERROR
PPP: couldn't register device %s (%d),
ppp: destroying ppp struct %p but
dead=%d
ERROR
ERROR
DEBUG
ppp: destroying undead channel %p !,
PPP: removing module but units
remain!
DEBUG
PPP: failed to unregister PPP device
ERROR
DEBUG
JBD: bad block at offset %u,
ERROR
DEBUG
DEBUG
JBD: corrupted journal superblock
JBD: bad block at offset %u,
ERROR
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
JBD: Failed to read block at offset %u,
JBD: error %d scanning journal, err
JBD: IO error %d recovering block
./Logs_kernel.txt:303:KERN_ERR
./Logs_kernel.txt:304:KERN_ERR
ERROR
ERROR
ERROR
ERROR
ERROR
DEBUG
JBD: recovery pass %d ended at
ERROR
DEBUG
DEBUG
%s: %s:%d: BAD SESSION MAGIC \
%s: %s:%d: BAD TUNNEL MAGIC \
ERROR
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
ERROR
ERROR
ERROR
%s%s, sep, ath_hal_buildopts[i]
failed to allocate rx descriptors: %d,
error
DEBUG
DEBUG
msg->msg_namelen wrong, %d, msg>msg_namelen
addr family wrong: %d, usin>sin_family
ath_stoprecv: rx queue %p, link %p,
no mpdu (%s), __func__
Reset rx chain mask. Do internal reset.
(%s), __func__
OS_CANCEL_TIMER failed!!
%s: unable to allocate channel table,
__func__
%s: unable to collect channel list from
hal;
%s: cannot map channel to mode; freq
%u flags 0x%x,
DEBUG
DEBUG
udp addr=%x/%hu, usin>sin_addr.s_addr, usin->sin_port
%s: %s:%d: BAD TUNNEL MAGIC
ERROR
ERROR
DEBUG
DEBUG
%s: %s:%d: BAD TUNNEL MAGIC
socki_lookup: socket file changed!
ERROR
ERROR
DEBUG
%s: %s:%d: BAD TUNNEL MAGIC
ERROR
DEBUG
%s: %s:%d: BAD SESSION MAGIC \
ERROR
DEBUG
%s: %s:%d: BAD TUNNEL MAGIC \
ERROR
%s: unable to reset channel %u
(%uMhz)
DEBUG
%s: unable to restart recv logic,
DEBUG
msg->msg_namelen wrong, %d, msg>msg_namelen
addr family wrong: %d, usin>sin_family
DEBUG
udp addr=%x/%hu, usin>sin_addr.s_addr, usin->sin_port
%s: start DFS WAIT period on channel
%d, __func__,sc->sc_curchan.channel
207
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
%s: cancel DFS WAIT period on
channel %d, __func__, sc>sc_curchan.channel
Non-DFS channel, cancelling previous
DFS wait timer channel %d, sc>sc_curchan.channel
%s: unable to reset hardware; hal status
%u
%s: unable to start recv logic, __func__
%s: unable to start recv logic, __func__
%s: unable to reset hardware; hal status
%u,
User Manual
DEBUG
%s: %s:%d: BAD TUNNEL MAGIC
ERROR
DEBUG
%s: %s:%d: BAD TUNNEL MAGIC
ERROR
DEBUG
DEBUG
DEBUG
socki_lookup: socket file changed!
%s: %s:%d: BAD TUNNEL MAGIC
%s: %s:%d: BAD SESSION MAGIC \
ERROR
ERROR
ERROR
DEBUG
%s: %s:%d: BAD TUNNEL MAGIC \
ERROR
hardware error; reseting
DEBUG
rx FIFO overrun; reseting
DEBUG
msg->msg_namelen wrong, %d, msg>msg_namelen
addr family wrong: %d, usin>sin_family
DEBUG
udp addr=%x/%hu, usin>sin_addr.s_addr, usin->sin_port
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
%s: %s:%d: BAD TUNNEL MAGIC
%s: %s:%d: BAD TUNNEL MAGIC
socki_lookup: socket file changed!
%s: %s:%d: BAD TUNNEL MAGIC
rebootHook: null function pointer
ERROR
ERROR
ERROR
ERROR
ERROR
DEBUG
Bad ioctl command
ERROR
DEBUG
fResetMod: Failed to configure gpio pin
ERROR
DEBUG
fResetMod: Failed to register interrupt
handler
ERROR
DEBUG
registering char device failed
ERROR
DEBUG
unregistering char device failed
ERROR
DEBUG
proc entry delete failed
ERROR
DEBUG
proc entry initialization failed
ERROR
DEBUG
testCompHandler: received %s from
%d, (char *)pInBuf,
ERROR
DEBUG
DEBUG
UMI proto registration failed %d,ret
AF_UMI registration failed %d,ret
ERROR
ERROR
DEBUG
DEBUG
DEBUG
ERROR
ERROR
ERROR
DEBUG
DEBUG
umi initialization failed %d,ret
kernel UMI registration failed!
./Logs_kernel.txt:447:KERN_ERR
ERROR msm not found properly %d,
len %d, msm,
ModExp returned Error
DEBUG
DEBUG
ModExp returned Error
%s: 0x%p len %u, tag, p, (unsigned
ERROR
ERROR
%s: During Wow Sleep and got BMISS,
__func__
AC\tRTS \tAggr Scaling\tMin
Rate(Kbps)\tHBR \tPER LOW
THRESHOLD
BE\t%s\t\t%d\t%6d\t\t%s\t%d,
BK\t%s\t\t%d\t%6d\t\t%s\t%d,
VI\t%s\t\t%d\t%6d\t\t%s\t%d,
VO\t%s\t\t%d\t%6d\t\t%s\t%d,
--%d,%p,%lu:0x%x 0x%x 0x%p 0x%x
0x%x 0x%x 0x%x,
bb state: 0x%08x 0x%08x, bbstate(sc,
4ul), bbstate(sc, 5ul)
%08x %08x %08x %08x %08x %08x
%08x %08x%08x %08x %08x %08x,
noise floor: (%d, %d) (%d, %d) (%d,
%d),
%p: %08x %08x %08x %08x %08x
%08x %08x %08x %08x %08x %08x
%08x,
--%d,%p,%lu:0x%x 0x%x 0x%p 0x%x
0x%x 0x%x 0x%x,
%08x %08x %08x %08x %08x %08x
%08x %08x%08x %08x %08x %08x,
%s: unable to allocate device object.,
__func__
%s: unable to attach hardware; HAL
status %u,
%s: HAL ABI msmatch;
%s: Warning, using only %u entries in
%u key cache,
unable to setup a beacon xmit queue!
unable to setup CAB xmit queue!
unable to setup xmit queue for BE
traffic!
%s DFS attach failed, __func__
%s: Invalid interface id = %u, __func__,
if_id
%s:grppoll Buf allocation failed
208
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
,__func__
int)len
%s: unable to start recv logic,
%s: Invalid interface id = %u, __func__,
if_id
%s: unable to allocate channel table,
__func__
%s: Tx Antenna Switch. Do internal
reset., __func__
Radar found on channel %d (%d MHz),
End of DFS wait period
%s error allocating beacon, __func__
failed to allocate UAPSD QoS NULL tx
descriptors: %d, error
failed to allocate UAPSD QoS NULL
wbuf
%s: unable to allocate channel table,
__func__
%s: unable to update h/w beacon queue
parameters,
ALREADY ACTIVATED
%s: missed %u consecutive beacons,
%s: busy times: rx_clear=%d,
rx_frame=%d, tx_frame=%d, __func__,
rx_clear, rx_frame, tx_frame
%s: unable to obtain busy times,
__func__
%s: beacon is officially stuck,
DEBUG
%03d:, i
ERROR
DEBUG
%02x, ((unsigned char *)p)[i]
ERROR
DEBUG
ERROR
DEBUG
DEBUG
DEBUG
DEBUG
mic check failed
%s: 0x%p len %u, tag, p, (unsigned
int)len
%03d:, i
%02x, ((unsigned char *)p)[i]
mic check failed
DEBUG
[%s] Wrong parameters, __func__
ERROR
DEBUG
[%s] Wrong Key length, __func__
ERROR
DEBUG
[%s] Wrong parameters, __func__
ERROR
DEBUG
DEBUG
DEBUG
[%s] Wrong Key length, __func__
[%s] Wrong parameters, __func__
[%s] Wrong Key length, __func__
ERROR
ERROR
ERROR
DEBUG
[%s] Wrong parameters, __func__
ERROR
DEBUG
DEBUG
ERROR
ERROR
Busy environment detected
DEBUG
Inteference detected
rx_clear=%d, rx_frame=%d,
tx_frame=%d,
%s: resume beacon xmit after %u
misses,
%s: stuck beacon; resetting (bmiss
count %u),
EMPTY QUEUE
SWRInfo: seqno %d isswRetry %d
retryCnt %d,wh ? (*(u_int16_t *)&wh>i_seq[0]) >> 4 : 0, bf->bf_isswretry,bf>bf_swretries
Buffer #%08X --> Next#%08X
Prev#%08X Last#%08X,bf,
TAILQ_NEXT(bf,bf_list),
Stas#%08X flag#%08X
Node#%08X, bf->bf_status, bf>bf_flags, bf->bf_node
Descr #%08X --> Next#%08X
Data#%08X Ctl0#%08X Ctl1#%08X, bf>bf_daddr, ds->ds_link, ds->ds_data,
ds->ds_ctl0, ds->ds_ctl1
Ctl2#%08X Ctl3#%08X
Sta0#%08X Sta1#%08X,ds->ds_hw[0],
ds->ds_hw[1], lastds->ds_hw[2], lastds>ds_hw[3]
Error entering wow mode
DEBUG
DEBUG
[%s] Wrong Key length, __func__
[%s]: Wrong parameters, __func__
[%s] Wrong Key Length %d, __func__,
des_key_len
[%s] Wrong parameters %d, __func__,
des_key_len
[%s] Wrong Key Length %d, __func__,
des_key_len
DEBUG
[%s] Wrong parameters, __func__
ERROR
DEBUG
DEBUG
[%s] Wrong Key Length, __func__
[%s] Wrong parameters, __func__
ERROR
ERROR
DEBUG
[%s] Wrong Key Length, __func__
ERROR
DEBUG
[%s] Wrong parameters, __func__
ERROR
DEBUG
[%s] Wrong parameters, __func__
ERROR
DEBUG
[%s] Wrong parameters, __func__
ERROR
DEBUG
DEBUG
[%s] Wrong parameters, __func__
device name=%s not found, pReq-
ERROR
ERROR
209
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
>ifName
Wakingup due to wow signal
%s, wowStatus = 0x%x, __func__,
wowStatus
DEBUG
Pattern added already
Error : All the %d pattern are in use.
Cannot add a new pattern ,
MAX_NUM_PATTERN
DEBUG
Pattern added to entry %d ,i
Remove wake up pattern
mask = %p pat = %p
,maskBytes,patternBytes
mask = %x pat = %x
,(u_int32_t)maskBytes,
(u_int32_t)patternBytes
Pattern Removed from entry %d ,i
DEBUG
DEBUG
Error : Pattern not found
DEBUG
PPM STATE ILLEGAL %x %x,
forcePpmStateCur, afp->forceState
FORCE_PPM %4d %6.6x %8.8x %8.8x
%8.8x %3.3x %4.4x,
failed to allocate tx descriptors: %d,
error
failed to allocate beacon descripotrs:
%d, error
failed to allocate UAPSD descripotrs:
%d, error
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
unable to register KIFDEV to UMI
ERROR: %s: Timeout at page %#0x
addr %#0x
ERROR: %s: Timeout at page %#0x
addr %#0x
ERROR
Invalid IOCTL %#08x, cmd
%s: unable to register device, dev>name
ath_pci: 32-bit DMA not available
ath_pci: cannot reserve PCI memory
region
ERROR
ath_pci: cannot remap PCI memory
region) ;
ath_pci: no memory for device state
%s: unable to register device, dev>name
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
DEBUG
ath_dev_probe: no memory for device
state
%s: no memory for device state,
__func__
DEBUG
kernel MIBCTL registration failed!
ERROR
DEBUG
Bad ioctl command
ERROR
DEBUG
ERROR
DEBUG
hal qnum %u out of range, max %u!,
HAL AC %u out of range, max %zu!,
HAL AC %u out of range, max %zu!,
DEBUG
DEBUG
DEBUG
WpsMod: Failed to configure gpio pin
WpsMod: Failed to register interrupt
handler
registering char device failed
unregistering char device failed
%s: unable to update hardware queue
%u!,
DEBUG
%s:%d - ERROR: non-NULL node
pointer in %p, %p<%s>!
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
Multicast Q:
%p , buf
buf flags - 0x%08x --------- , buf>bf_flags
DEBUG
DEBUG
buf status - 0x%08x, buf->bf_status
# frames in aggr - %d, length of
aggregate - %d, length of frame - %d,
sequence number - %d, tidno - %d,
isdata: %d isaggr: %d isampdu: %d ht:
%d isretried: %d isxretried: %d
shpreamble: %d isbar: %d ispspoll: %d
aggrburst: %d calcairtime: %d
qosnulleosp: %d,
%p: 0x%08x 0x%08x 0x%08x 0x%08x
0x%08x 0x%08x 0x%08x 0x%08x
0x%08x 0x%08x,
DEBUG
%s:%d - ERROR: non-NULL node
pointer in %p, %p<%s>!
can't alloc name %s, name
%s: unable to register device, dev>name
failed to automatically load module:
%s; \
DEBUG
Unable to load needed module: %s; no
support for \
ERROR
DEBUG
Module \%s\ is not known, buf
ERROR
DEBUG
Error loading module \%s\, buf
ERROR
DEBUG
Module \%s\ failed to initialize, buf
ERROR
0x%08x 0x%08x 0x%08x 0x%08x
0x%08x 0x%08x 0x%08x 0x%08x
DEBUG
210
ERROR
ERROR
ERROR
ERROR
Unified Services Router
User Manual
0x%08x 0x%08x,
0x%08x 0x%08x 0x%08x 0x%08x,
DEBUG
sc_txq[%d] : , i
DEBUG
tid %p pause %d : , tid, tid->paused
%d: %p , j, tid->tx_buf[j]
DEBUG
DEBUG
%p , buf
axq_q:
%s: unable to reset hardware; hal status
%u, __func__, status
DEBUG
DEBUG
****ASSERTION HIT****
MacAddr=%s,
DEBUG
DEBUG
TxBufIdx=%d, i
DEBUG
Tid=%d, tidno
AthBuf=%p, tid->tx_buf[i]
%s: unable to reset hardware; hal status
%u,
%s: unable to reset hardware; hal status
%u,
DEBUG
DEBUG
%s: unable to start recv logic,
DEBUG
_fmt, __VA_ARGS__ \
sample_pri=%d is a multiple of
refpri=%d, sample_pri, refpri
===========ft>ft_numfilters=%u===========, ft>ft_numfilters
filter[%d] filterID = %d
rf_numpulses=%u; rf->rf_minpri=%u; rf>rf_maxpri=%u; rf->rf_threshold=%u; rf>rf_filterlen=%u; rf->rf_mindur=%u; rf>rf_maxdur=%u,j, rf->rf_pulseid,
NOL
DEBUG
WARNING!!! 10 minute CAC period as
channel is a weather radar channel
%s disable detects, __func__
%s enable detects, __func__
%s disable FFT val=0x%x , __func__,
val
%s enable FFT val=0x%x , __func__,
val
%s debug level now = 0x%x , __func__,
dfs_debug_level
RateTable:%d, maxvalidrate:%d,
ratemax:%d, pRc->rateTableSize,k,pRc>rateMaxPhy
%s: txRate value of 0x%x is bad.,
__FUNCTION__, txRate
Valid Rate Table:-
ath_pci: 32-bit DMA not available
ath_pci: cannot reserve PCI memory
region
ath_pci: cannot remap PCI memory
region) ;
ath_pci: no memory for device state
%s: unable to attach hardware: '%s'
(HAL status %u),
%s: HAL ABI mismatch;
ERROR
ERROR
DEBUG
%s: failed to allocate descriptors: %d,
%s: unable to setup a beacon xmit
queue!,
%s: unable to setup CAB xmit queue!,
%s: unable to setup xmit queue for %s
traffic!,
%s: unable to register device, dev>name
%s: autocreation of VAP failed: %d,
ath_dev_probe: no memory for device
state
kdot11RogueAPEnable called with
NULL argument.
kdot11RogueAPEnable: can not add
more interfaces
kdot11RogueAPGetState called with
NULL argument.
kdot11RogueAPDisable called with
NULL argument.
DEBUG
%s: SKB does not exist.,
__FUNCTION__
ERROR
DEBUG
DEBUG
%s: recvd invalid skb
unable to register KIFDEV to UMI
ERROR
ERROR
DEBUG
DEBUG
DEBUG
The system is going to factory
defaults........!!!
%s, msg
%02x, *(data + i)
CRITICAL
CRITICAL
CRITICAL
DEBUG
Inside crypt_open in driver ######
CRITICAL
DEBUG
CRITICAL
DEBUG
Inside crypt_release in driver ######
Inside crypt_init module in driver
@@@@@@@@
DEBUG
Inside crypt_cleanup module in driver
@@@@@@@@
CRITICAL
DEBUG
DEBUG
SKB is null : %p ,skb
DST is null : %p ,dst
CRITICAL
CRITICAL
DEBUG
DEBUG
DEBUG
211
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
CRITICAL
Unified Services Router
Index:%d, value:%d, code:%x, rate:%d,
flag:%x, i, (int)validRateIndex[i],
RateTable:%d, maxvalidrate:%d,
ratemax:%d, pRc->rateTableSize,k,pRc>rateMaxPhy
User Manual
DEBUG
DEBUG
Can't allocate memory for ath_vap.
DEBUG
Unable to add an interface for ath_dev.
%s: [%02u] %-7s , tag, ix, ciphers[hk>kv_type]
%02x, hk->kv_val[i]
mac %02x-%02x-%02x-%02x-%02x%02x, mac[0], mac[1], mac[2], mac[3],
mac[4], mac[5]
DEBUG
mac 00-00-00-00-00-00
DEBUG
%02x, hk->kv_mic[i]
DEBUG
txmic
DEBUG
%02x, hk->kv_txmic[i]
DEBUG
Cannot support setting tx and rx keys
individually
bogus frame type 0x%x (%s),
DEBUG
DEBUG
DEBUG
DEBUG
DEV is null %p %p ,dev,dst
Packet is Fragmented %d,pBufMgr>len
Marked the packet proto:%d sip:%x
dip:%x sport:%d dport:%d
spi:%d,isr:%p:%p %p
SAV CHECK FAILED IN
DECRYPTION
CRITICAL
CRITICAL
CRITICAL
CRITICAL
ERROR: ieee80211_encap ret NULL
ERROR: ath_amsdu_attach not called
%s: no memory for cwm attach,
__func__
%s: error - acw NULL. Possible attach
failure, __func__
%s: unable to abort tx dma, __func__
%s: no memory for ff attach, __func__
Failed to initiate PBC based enrolle
association
KERN_EMERG Returing error in INTR
registration
DEBUG
DEBUG
FAST PATH Breaks on BUF CHECK
FAST PATH Breaks on DST CHECK
FAST PATH Breaks on MTU %d %d
%d,bufMgrLen(pBufMgr),mtu,dst_mtu(
pDst->path)
FAST PATH Breaks on MAX PACKET
%d
%d,bufMgrLen(pBufMgr),IP_MAX_PA
CKET
SAV CHECK FAILED IN
ENCRYPTION
Match Found proto %d spi
%d,pPktInfo->proto,pFlowEntry>pre.spi
PRE: proto: %u srcip:%u.%u.%u.%u
sport :%u dstip: %u.%u.%u.%u dport:
%u,
POST: proto: %u srcip:%u.%u.%u.%u
sport :%u dstip: %u.%u.%u.%u dport:
%u,
Clearing the ISR %p,p
PROTO:%d %u.%u.%u.%u-->%u.%u.%u.%u,
ESP-DONE: %p %p,sav,m
DEBUG
ESP-BAD: %p %p,sav,m
CRITICAL
DEBUG
DEBUG
DEBUG
Bug in ip_route_input_slow().
Bug in ip_route_input_slow().
Bug in ip_route_input \
CRITICAL
CRITICAL
CRITICAL
DEBUG
CRITICAL
KERN_EMERG Initialzing Wps module
DEBUG
%s:%d %s, __FILE__, __LINE__,
__func__
DEBUG
Bug in ip_route_input_slow().
AH: Assigning the secure flags for sav
:%p,sav
ESP: Assigning the secure flags for
sav :%p skb:%p src:%x
dst:%x,sav,skb,ip->ip_src.s_addr,ip>ip_dst.s_addr
%s Buffer %d mtu %d path mtu %d
header %d trailer
%d,__func__,bufMgrLen(pBufMgr),mtu
,dst_mtu(pDst->path),pDst>header_len,pDst->trailer_len
DEBUG
DEBUG
212
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
Unified Services Router
User Manual
Appendix E. RJ-45 Pin-outs
RJ-45
Cable
Adapter
RJ-45 PIN
DB-9 PIN
CTS
NC
NC
NC
DTR
NC
NC
NC
TxD
RxD
GND
GND
GND
GND
RxD
TxD
DSR
NC
NC
NC
RTS
NC
NC
NC
Signal
Signal
213
Unified Services Router
User Manual
Appendix F. Product Statement
1. DSR-1000N
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the
radiator and your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1)
2)
This device may not cause harmful interference, and
This device must accept any interference received, including
undesired operation.
interference that may cause
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a spectrum distance of at least 20cm
from all persons and must not be co-located or operating in conjunction with any other antenna or
transmitter.
This transmitter is restricted to indoor use in the 5150MHz to 5250MHz frequency range.
Non-modification Statement
Use only the integral antenna supplied by the manufacturer when operating this device. Unauthorized
antennas, modifications, or attachments could damage the TI Navigator access point and violate FCC
regulations. Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
Canadian Department of Communications Industry Canada (IC) Notice
This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Cet appareil numérique de
la classe B est conforme à la norme NMB-003 et CNR-210 du Canada.
ndustry Canada Statement
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause
undesired operation.
214
Unified Services Router
User Manual
IMPORTANT NOTE: Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End
users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain
compliance with IC RF exposure compliance requirements, please follow operation instruction as
documented in this manual.
This transmitter is restricted to indoor use in the 5150MHz to 5250MHz frequency range.
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following
test methods have been applied in order to prove presumption of conformity with the essential requirements
of the R&TTE Directive 1999/5/EC:
- EN 60950-1: 2006+A11:2009
Safety of information technology equipment
- EN 300 328 V1.7.1 (2006-10)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data
transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques;
Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive
- EN 301 893-1 V1.5.1 (2008-12)
Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN covering
essential requirements of article 3.2 of the R&TTE Directive
- EN 301 489-17 V1.3.2 (2008-04) and EN 301 489-1 V1.8.1 (2008-04)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Electro Magnetic Compatibility (EMC)
standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission
systems and 5 GHz high performance RLAN equipment
This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member
states and EFTA countries under the following conditions and/or with the following restrictions:
- In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain
authorization to use the device for setting up outdoor radio links and/or for supplying public access to
telecommunications and/or network services.
- This device may not be used for setting up outdoor radio links in France and in some areas the RF output
power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed
information the enduser should contact the national spectrum authority in France.
This device is a 5 GHz wideband transmission system (transceiver), intended for use in all EU member
states and EFTA countries under the following conditions and/or with the following restrictions:
- This device may only be used indoors in the frequency bands 5150 – 5250 MHz.
- In France and Luxembourg a limited implementation of the frequency bands 5150 – 5250 MHz and 5250 –
5350 MHz. In Luxermbourg it is not allowed to make use of the frequency band 5470 – 5725 MHz. Endusers are encouraged to contact the national spectrum authorities in France and Luxembourg in order to
obtain the latest information about any restrictions in the 5 GHz frequency band(s).
215
Unified Services Router
User Manual
Česky
[Czech]
[D-Link Corporation] tímto prohlašuje, že tento [DSR-1000N] je ve shodě se základními
požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk
[Danish]
Undertegnede [D-Link Corporation] erklærer herved, at følgende udstyr [DSR-1000N]
overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch
[German]
Hiermit erklärt [D-Link Corporation], dass sich das Gerät [DSR-1000N] in
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen
Bestimmungen der Richtlinie 1999/5/EG befindet.
Eesti
[Estonian]
Käesolevaga kinnitab [D-Link Corporation] seadme [DSR-1000N] vastavust direktiivi
1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele
sätetele.
English
Hereby, [D-Link Corporation], declares that this [DSR-1000N] is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente [D-Link Corporation] declara que el [DSR-1000N] cumple con
los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la
Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΣΗΝ ΠΑΡΟΤ΢Α [D-Link Corporation]
ΔΗΛΩΝΕΙ ΟΣΙ [DSR-1000N]
΢ΤΜΜΟΡΦΩΝΕΣΑΙ ΠΡΟ΢ ΣΙ΢ ΟΤ΢ΙΩΔΕΙ΢ ΑΠΑΙΣΗ΢ΕΙ΢ ΚΑΙ ΣΙ΢ ΛΟΙΠΕ΢ ΢ΥΕΣΙΚΕ΢
ΔΙΑΣΑΞΕΙ΢ ΣΗ΢ ΟΔΗΓΙΑ΢ 1999/5/ΕΚ.
Français
[French]
Par la présente [D-Link Corporation] déclare que l'appareil [DSR-1000N] est conforme
aux exigences essentielles et aux autres dispositions pertinentes de la directive
1999/5/CE.
Italiano
[Italian]
Con la presente [D-Link Corporation] dichiara che questo [DSR-1000N] è conforme ai
requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski
[Latvian]
Ar šo [D-Link Corporation] deklarē, ka [DSR-1000N] atbilst Direktīvas 1999/5/EK
būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių
[Lithuanian]
Šiuo [D-Link Corporation] deklaruoja, kad šis [DSR-1000N] atitinka esminius reikalavimus
ir kitas 1999/5/EB Direktyvos nuostatas.
Nederlands
[Dutch]
Hierbij verklaart [D-Link Corporation] dat het toestel [DSR-1000N] in overeenstemming is
met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Malti
[Maltese]
Hawnhekk, [D-Link Corporation], jiddikjara li dan [DSR-1000N] jikkonforma mal-ħtiġijiet
essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar
[Hungarian]
Alulírott, [D-Link Corporation] nyilatkozom, hogy a [DSR-1000N] megfelel a vonatkozó
alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Polski
[Polish]
Niniejszym [D-Link Corporation] oświadcza, że [DSR-1000N] jest zgodny z zasadniczymi
wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
216
Unified Services Router
Português
[Portuguese]
Slovensko
[Slovenian]
Slovensky
[Slovak]
User Manual
[D-Link Corporation] declara que este [DSR-1000N]está conforme com os requisitos
essenciais e outras disposições da Directiva 1999/5/CE.
[D-Link Corporation] izjavlja, da je ta [DSR-1000N] v skladu z bistvenimi zahtevami in
ostalimi relevantnimi določili direktive 1999/5/ES.
[D-Link Corporation] týmto vyhlasuje, že [DSR-1000N] spĺňa základné požiadavky a
všetky príslušné ustanovenia Smernice 1999/5/ES.
Suomi
[Finnish]
[D-Link Corporation] vakuuttaa täten että [DSR-1000N] tyyppinen laite on direktiivin
1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Svenska
[Swedish]
Härmed intygar [D-Link Corporation] att denna [DSR-1000N] står I överensstämmelse
med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av
direktiv 1999/5/EG.
217
Unified Services Router
User Manual
2.DSR-500N
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the
radiator and your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1)
2)
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause
undesired operation.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a spectrum distance of at least 20cm
from all persons and must not be co-located or operating in conjunction with any other antenna or
transmitter.
This transmitter is restricted to indoor use in the 5150MHz to 5250MHz frequency range.
Non-modification Statement
Use only the integral antenna supplied by the manufacturer when operating this device. Unauthorized
antennas, modifications, or attachments could damage the TI Navigator access point and violate FCC
regulations. Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
Canadian Department of Communications Industry Canada (IC) Notice
This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Cet appareil numérique de
la classe B est conforme à la norme NMB-003 et CNR-210 du Canada.
Industry Canada Statement
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause
undesired operation.
IMPORTANT NOTE: Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
End users must follow the specific operating instructions for satisfying RF exposure compliance.
To maintain compliance with IC RF exposure compliance requirements, please follow operation instruction
as documented in this manual.
218
Unified Services Router
User Manual
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following
test methods have been applied in order to prove presumption of conformity with the essential requirements
of the R&TTE Directive 1999/5/EC:
- EN 60950-1: 2006+A11:2009
Safety of information technology equipment
- EN 300 328 V1.7.1 (2006-10)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data
transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques;
Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive
- EN 301 489-17 V1.3.2 (2008-04) and EN 301 489-1 V1.8.1 (2008-04)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Electro Magnetic Compatibility (EMC)
standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission
systems and 5 GHz high performance RLAN equipment
This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member
states and EFTA countries under the following conditions and/or with the following restrictions:
- In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization
to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or
network services.
- This device may not be used for setting up outdoor radio links in France and in some areas the RF output
power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the
enduser should contact the national spectrum authority in France.
219
Unified Services Router
User Manual
Česky
[Czech]
[D-Link Corporation] tímto prohlašuje, že tento [DSR-500N] je ve shodě se základními
požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk
[Danish]
Undertegnede [D-Link Corporation] erklærer herved, at følgende udstyr [DSR-500N]
overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch
[German]
Hiermit erklärt [D-Link Corporation], dass sich das Gerät [DSR-500N] in Übereinstimmung
mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der
Richtlinie 1999/5/EG befindet.
Eesti
[Estonian]
Käesolevaga kinnitab [D-Link Corporation] seadme [DSR-500N] vastavust direktiivi
1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele
sätetele.
English
Hereby, [D-Link Corporation], declares that this [DSR-500N] is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente [D-Link Corporation] declara que el [DSR-500N] cumple con los
requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la
Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΣΗΝ ΠΑΡΟΤ΢Α [D-Link Corporation] ΔΗΛΩΝΕΙ ΟΣΙ [DSR-500N] ΢ΤΜΜΟΡΦΩΝΕΣΑΙ
ΠΡΟ΢ ΣΙ΢ ΟΤ΢ΙΩΔΕΙ΢ ΑΠΑΙΣΗ΢ΕΙ΢ ΚΑΙ ΣΙ΢ ΛΟΙΠΕ΢ ΢ΥΕΣΙΚΕ΢ ΔΙΑΣΑΞΕΙ΢ ΣΗ΢
ΟΔΗΓΙΑ΢ 1999/5/ΕΚ.
Français
[French]
Par la présente [D-Link Corporation] déclare que l'appareil [DSR-500N] est conforme aux
exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Italiano
[Italian]
Con la presente [D-Link Corporation] dichiara che questo [DSR-500N] è conforme ai
requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski
[Latvian]
Ar šo [D-Link Corporation] deklarē, ka [DSR-500N] atbilst Direktīvas 1999/5/EK
būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių
[Lithuanian]
Šiuo [D-Link Corporation] deklaruoja, kad šis [DSR-500N] atitinka esminius reikalavimus
ir kitas 1999/5/EB Direktyvos nuostatas.
Nederlands
[Dutch]
Hierbij verklaart [D-Link Corporation] dat het toestel [DSR-500N] in overeenstemming is
met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Malti
[Maltese]
Hawnhekk, [D-Link Corporation], jiddikjara li dan [DSR-500N] jikkonforma mal-ħtiġijiet
essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar
[Hungarian]
Alulírott, [D-Link Corporation] nyilatkozom, hogy a [DSR-500N] megfelel a vonatkozó
alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Polski
[Polish]
Niniejszym [D-Link Corporation] oświadcza, że [DSR-500N] jest zgodny z zasadniczymi
wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
220
Unified Services Router
Português
[Portuguese]
Slovensko
[Slovenian]
Slovensky
[Slovak]
User Manual
[D-Link Corporation] declara que este [DSR-500N]está conforme com os requisitos
essenciais e outras disposições da Directiva 1999/5/CE.
[D-Link Corporation] izjavlja, da je ta [DSR-500N] v skladu z bistvenimi zahtevami in
ostalimi relevantnimi določili direktive 1999/5/ES.
[D-Link Corporation] týmto vyhlasuje, že [DSR-500N] spĺňa základné požiadavky a
všetky príslušné ustanovenia Smernice 1999/5/ES.
Suomi
[Finnish]
[D-Link Corporation] vakuuttaa täten että [DSR-500N] tyyppinen laite on direktiivin
1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Svenska
[Swedish]
Härmed intygar [D-Link Corporation] att denna [DSR-500N] står I överensstämmelse
med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av
direktiv 1999/5/EG.
221
Unified Services Router
User Manual
3.DSR-250N
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:




Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
You are cautioned that changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the
radiator and your body.
RSS-GEN 7.1.2:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference
to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter (identify the device by certification number, or model number if Category II) has been
approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and
required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
RSS-GEN 7.1.3
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
222
Unified Services Router
User Manual
Is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation
of the Laws of the Member States relating to Electromagnetic Compatibility (2004/108/EC), Low-voltage
Directive (2006/95/EC), the procedures given in European Council Directive 99/5/EC and 2004/104/EC.
The equipment was passed. The test was performed according to the following European standards:
EN 300 328 V.1.7.1
EN 301 489-1 V.1. 8.1 / EN 301 489-17 V.2.1.1
EN 62311
EN 60950-1
Regulatory statement (R&TTE)
European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range 2.4002.4835GHz; In France, the equipment must be restricted to the 2.4465-2.4835GHz frequency range and
must be restricted to indoor use.
Operation of this device is subjected to the following National regulations and may be prohibited to use if
certain restriction should be applied.
D=0.020m is the minimum safety distance between the EUT and human body when the E-Field strength is
61V/m.
223

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Modify Date                     : 2011:06:24 15:54:45+08:00
Create Date                     : 2011:06:20 15:00:53+08:00
Creator                         : Microsoft® Word 2010
Producer                        : Microsoft® Word 2010
Page Count                      : 75
Has XFA                         : No
About                           : uuid:c0d95b64-bc97-4798-a5ea-26ff7b66ae92
Mod Date                        : 2011:06:24 15:54:45+08:00
Creation Date                   : 2011:06:20 15:00:53+08:00
Metadata Date                   : 2011:06:24 15:54:45+08:00
Document ID                     : uuid:75d375a1-3b0b-4a6b-8e85-c84cf736c3fa
Format                          : application/pdf

EXIF Metadata provided by EXIF.tools

D Link SR250NA1 Wireless N Service Router User Manual 2 of 2

D Link Corporation Wireless N Service Router 2 of 2

Contents

User manual 2 of 2

FCC ID Filing: KA2SR250NA1

Navigation menu

Namespaces

Views

Navigation