DASAN Network Solutions H640W G-PON ONT User Manual H640W N A QIG EN 131105 V1

Download:
Mirror Download [FCC.gov]
Document ID	2124614
Application ID	H5EZsLSbOAdklboq3mGEpQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	145.4kB (1817460 bits)
Date Submitted	2013-11-21 00:00:00
Date Available	2014-05-20 00:00:00
Creation Date	2013-11-05 15:16:44
Producing Software	Adobe PDF library 10.01
Document Lastmod	2013-11-05 15:16:45
Document Title	[H640W_N.A]_QIG_EN_131105_V1
Document Creator	Adobe Illustrator CS6 (Windows)

4. Initial Web Access
1. Caution
You can access H640W through a web browser by using the “initial
LAN IP” at first. The detail procedure is as follows:
① Connect LAN1 port of H640W to your PC using Ethernet cable.
② Configure IP assignment of your PC to DHCP (dynamic assignment).
How to configure dynamic IP on your PC is as follows:
For Windows XP:
Start > Setting > Network Connections > Local Area Connection
double click > Internet Protocol (TCP/IP) double click > Obtain an
IP address automatically and Obtain DNS server address
automatically selection > OK
For Windows 7:
Start > Control Panel > View network status and tasks under
Network and Internet (View by: Category) > Change adapter
settings on the left menu > Local Area Connection right-click >
Properties > Internet Protocol Version 4 (TCP/IPv4) double click >
> Obtain an IP address automatically and Obtain DNS server
address automatically selection > OK
The PC will be allocated 192.168.1.1~254 automatically through
H640W.
- This unit is indoor use and all the communication wirings are limited to inside of the building.
- Never look directly at the fiber TX port and fiber cable ends when they are powered on.
- DO NOT use near water.
- DO NOT place near high temperature source.
- DO NOT disassemble the unit.
- DO NOT operate the unit in a location where the maximum ambient temperature exceeds 104°F.
- Open optical connections must use a protective cap under all circumstances to protect against
physical damage and dirt.
- Avoid impact stresses when handling connectors. Physical damage to the faces of optical
connections impairs transmission quality (higher attenuation).
- Avoid a bend radius in excess of 1.18 in for fiber optic links.
- Check the available voltage supply.
- Only connect approved accessories.
- It may only be repaired by authorized service personnel.
③ Open a web browser, and enter http://192.168.1.100:8080 in a
URL field.
④ Type “user/user” in user name/password field, and log into the
system. Initial page is displayed.
※ The default SSID and its key are as follows:
SSID: DASAN_GONT / Key: 1234567890a
※ To change the password, on the web above, Basic Settings >
Wireless LAN > SSID Setting > Click Modify > Change password >
Click Apply.
H640W
QIG (Quick Guide)
V1
GPON Optical Network Terminal (ONT) with Wi-Fi
Information furnished by DASAN Networks USA, Inc. is believed to be accurate and reliable. However, no responsibility
is assumed by DASAN Networks for its use, nor for any infringements of patents or other rights of third parties which
may result from its use. No license is granted by implication or otherwise under any patent or patent rights of DASAN
Networks. DASAN Networks reserves the rights to change specifications at any time without notice.
Copyright © 2013 by DASAN Networks USA, Inc. All rights reserved.
DASAN Networks USA, Inc.
5000 Research Court, Suite 700, Suwanee, GA 30024
www.dasannetworksus.com
DASAN Networks USA, Inc.
Green
PON
Green
FCC Certification Requirements
Flash Memory
128MB Nand Flash
● Caution
Any changed or modifications not expressly approved by the party responsible for
compliance could void the user`s authority to operate this equipment.
● FCC RF exposure requirements
The antenna used with this module must be installed to provide a separation distance of
at least 20cm from all persons, and must not transmit simultaneously with any other
antenna or transmitter except in accordance with FCC multi-transmitter product
procedures.
● User Information
This device complies with Part 15 of the FCC`s Rule. Operation is subject to the following
to conditions;
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Uplink Interface
1 GPON port (SC/APC)
Service Interface
4 10/100/1000Base-T ports (RJ45)
Wireless
2 detachable antennas
IEEE 802.11b/g/n compliant
Bandwidth: 2.4GHz
Two Transmit and Two Receive path (2T2R)
USB Interface
1 USB host
LED
PWR, PON, LOS, USB, WLAN, LAN1~4
AC/DC Adapter
12VDC/1.5A
Power Consumption
Max. 14W
Operating Temp.
0 ~ 40°C
Relative Humidity
5 ~ 95% (non-condensing)
Dimensions
(W x D x H)
160 × 147 × 40 mm
Button
On/Off power switch, WLAN, RESET
Description
Connect the network.
② LAN1~4
Connect PC or LAN.
③ USB
Connect an external USB device for management.
④ ON/OFF
Turn on/off the unit.
⑤ Power Port
Connect power adapter.
⑥ RESET
Reboot the unit.
⑦ WLAN
Enable wireless function.
⑧ Antenna
Transmit and receive wireless packets.
Off
The system is turned off.
On
Register OK. The SFF port link is up.
Not register. The SFF port link is down.
Off
Received optical power normal
Blink
On
Orange
Blink
Off
Green
WLAN Green
GPON Port
Fixing Screw
Received optical power is less than optical receiver
sensitivity.
The 1G port link is up.
The 1G transmit or receive activity is present
on the service port.
The 100M port link is up.
The 100M transmit or receive activity is present
on the service port.
Blink
USB is connected, and working normally.
USB is not connected, or power is not fed.
On
Wireless function enabled
Blink
Off
Line Guide
Data is being transmitted.
Off
Wireless transmit or receive activity is present.
Wireless function disabled
Link is down.
On
USB
Register is starting.
Off
Blink
Green
LAN
1~4
① OPTIC LINE
Red
② Connect the Ethernet cable from LAN port to PC.
③ Connect a power adapter from power port to a live AC outlet.
④ Turn on the unit by pushing the power switch.
⑤ Push WLAN button to enable WLAN.
⑥ Adjust antenna direction for better wireless communication. You can make
antennas oblique outside or inside the body by tilting and rotating them.
Description
The system is turned on.
Blink
Specification
128MB DDR3
3. Installation
On
On
Item
Status
PWR
LOS
Light
Item
System Memory
① Loosen a fixing screw, and pull the upper cover out to remove it. Connect an
SC/APC connector cable to GPON port, and then arrange optical line through splice
tray and line guide, not to give damage to GPON connection due to any possible
pull. And then close the cover, and fix it by tightening the screw.
Label
2.2 Specification
www.dasannetworksus.com
2.4 Front View (LEDs)
2.3 Rear View
H640W
Power Adapter
RJ45 UTP Cable
QIG (Quick Guide)
Splice Tray

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Producer                        : Adobe PDF library 10.01
Create Date                     : 2013:11:05 15:16:44+10:00
Modify Date                     : 2013:11:05 15:16:45+09:00
Creator Tool                    : Adobe Illustrator CS6 (Windows)
Metadata Date                   : 2013:11:05 15:16:45+09:00
Thumbnail Width                 : 256
Thumbnail Height                : 220
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 21194 bytes, use -b option to extract)
Document ID                     : xmp.did:DB82909CDF45E311A723A4D3577D4B65
Instance ID                     : uuid:13dcd047-2a94-4706-bbbf-682058abfbe6
Rendition Class                 : proof:pdf
Original Document ID            : uuid:699065b3-1b8a-469a-af8c-0e5ac3b8e540
Derived From Instance ID        : uuid:2374e785-17a5-4593-8cdb-1fc7bbe3c97b
Derived From Document ID        : xmp.did:DA82909CDF45E311A723A4D3577D4B65
Derived From Original Document ID: uuid:699065b3-1b8a-469a-af8c-0e5ac3b8e540
Derived From Rendition Class    : proof:pdf
History Action                  : saved, saved
History Instance ID             : xmp.iid:C678CFF8D10BE3118C389B3BAC7C7679, xmp.iid:DB82909CDF45E311A723A4D3577D4B65
History When                    : 2013:08:26 13:55:09+09:00, 2013:11:05 15:16:40+09:00
History Software Agent          : Adobe Illustrator CS6 (Windows), Adobe Illustrator CS6 (Windows)
History Changed                 : /, /
Format                          : application/pdf
Title                           : [H640W_N.A]_QIG_EN_131105_V1
N Pages                         : 1
Has Visible Transparency        : False
Has Visible Overprint           : False
Max Page Size W                 : 458.611111
Max Page Size H                 : 392.288889
Max Page Size Unit              : Millimeters
Font Name                       : Arial-ItalicMT, Calibri, Calibri-Italic, Calibri-Bold, Calibri-BoldItalic, YDISwiriM, YDIYMjO110, YDIBirdM, AdobeMyungjoStd-Medium, YDIYGO120
Font Family                     : Arial, Calibri, Calibri, Calibri, Calibri, -½¬¸®M, -윤명조110, -파랑새M, Adobe 명조 Std, YDIYGO120 KSCpc-EUC-H
Font Face                       : Italic, Regular, Italic, Bold, Bold Italic, Regular, Regular, Regular, M, KSCpc-EUC-H
Font Type                       : Open Type, Open Type, Open Type, Open Type, Open Type, TrueType, TrueType, TrueType, Open Type, Unknown
Font Version                    : Version 5.08, Version 1.02, Version 1.02, Version 1.02, Version 1.02, Version 1.00, Version 2.00, Version 1.012;PS 1.004;hotconv 1.0.67;makeotf.lib2.5.33168, Version 5.01
Font Composite                  : False, False, False, False, False, False, False, False, False, False
Font File Name                  : ariali.ttf, CALIBRI_0.TTF, CALIBRII_0.TTF, CALIBRIB_0.TTF, CALIBRIZ_0.TTF, , ymjo110.ttf, 파랑새m.ttf, AdobeMyungjoStd-Medium.otf, gulim.ttc
Plate Names                     : Cyan, Magenta, Yellow, Black, PANTONE 286 C, PANTONE 647 CVC, 100.65.5.45
Swatch Groups Group Name        : 기본 견본 그룹
Swatch Groups Group Type        : 0
Swatch Groups Colorants Swatch Name: New Color Swatch 3
Swatch Groups Colorants Type    : PROCESS
Swatch Groups Colorants Tint    : 100.000000
Swatch Groups Colorants Mode    : CMYK
Swatch Groups Colorants Cyan    : 23.140000
Swatch Groups Colorants Magenta : 16.080000
Swatch Groups Colorants Yellow  : 13.329999
Swatch Groups Colorants Black   : 1.960000
Page Count                      : 1
Creator                         : Adobe Illustrator(R) 16.0
For                             : kangth,
Bounding Box                    : 69 121 1352 1218
Container Version               : 11
Creator Version                 : 16
Image Height                    : 1097
Image Width                     : 1283
Image Size                      : 1283x1097
Megapixels                      : 1.4

EXIF Metadata provided by EXIF.tools