DASAN Network Solutions H660W G-PON ONT User Manual H660W CHT QIG EN 140828 V1

Download:
Mirror Download [FCC.gov]
Document ID	2409733
Application ID	fza0KB50D5n+tST907Ra9w==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	113.64kB (1420492 bits)
Date Submitted	2014-10-02 00:00:00
Date Available	2015-03-31 00:00:00
Creation Date	2014-08-28 16:34:13
Producing Software	Adobe PDF library 10.01
Document Lastmod	2014-08-28 16:34:14
Document Title	[H660W_CHT]_QIG_EN_140828_V1
Document Creator	Adobe Illustrator CS6 (Windows)

4. Initial Web Access
1. Caution
You can access the unit through a web browser by using the “initial
LAN IP” at first. The detail procedure is as follows:
① Connect LAN1 port of the unit to your PC using Ethernet cable.
② Configure IP assignment of your PC to DHCP (dynamic assignment).
How to configure dynamic IP on your PC is as follows:
For Windows XP:
Start > Setting > Network Connections > Local Area Connection
double click > Internet Protocol (TCP/IP) double click > Obtain an
IP address automatically and Obtain DNS server address
automatically selection > OK
For Windows 7:
Start > Control Panel > View network status and tasks under
Network and Internet (View by: Category) > Change adapter
settings on the left menu > Local Area Connection right-click >
Properties > Internet Protocol Version 4 (TCP/IPv4) double click >
> Obtain an IP address automatically and Obtain DNS server
address automatically selection > OK
The PC will be allocated IP address automatically through the unit.
- This unit is indoor use and all the communication wirings are limited to inside of the building.
- Never look directly at the fiber TX port and fiber cable ends when they are powered on.
- DO NOT use near water.
- DO NOT place near high temperature source.
- DO NOT disassemble the unit.
- DO NOT operate the unit in a location where the maximum ambient temperature exceeds 104°F.
- Open optical connections must use a protective cap under all circumstances to protect against
physical damage and dirt.
- Avoid impact stresses when handling connectors. Physical damage to the faces of optical
connections impairs transmission quality (higher attenuation).
- Avoid a bend radius in excess of 1.18 in for fiber optic links.
- Check the available voltage supply.
- It may only be repaired by authorized service personnel.
※ The default SSID and its password are as follows:
SSID: DASAN_GONTxxxxxx
(xxxxxx is the last 6 digit/letters of MAC address of your unit.)
Password: 1234567890a
※ To change the SSID and/or password, move onto Basic Settings > Wireless
LAN > SSID Setting on the web, and click Modify. And change them and
click Apply. And then click Apply Config on top of page, and reboot the unit.
H660W
QIG (Quick Guide)
V1
GPON Optical Network Terminal (ONT) with Wi-Fi
Information furnished by Dasan Networks, Inc. is believed to be accurate and reliable. However, no responsibility
is assumed by Dasan Networks for its use, nor for any infringements of patents or other rights of third parties which
may result from its use. No license is granted by implication or otherwise under any patent or patent rights of DASAN
Networks. DASAN Networks reserves the rights to change specifications at any time without notice.
Copyright © 2014 by DASAN Networks, Inc. All rights reserved.
DASAN Tower, 49, Daewangpangyo-ro 644 Beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 463-400 KOREA
DASAN Networks, Inc.
Label
PWR
Light
Status
Green
Red
Green
PON
Red
ALM
Orange
WLAN Green
Off
The system is turned off.
On
No optic signal.
On
Optic signal normal. Normally registered.
Blink
WPS
ONT not registered. Keep blinking before registration
process finished.
On
No optical signal, Firmware update fail or other faults.
Blink
Error rate high. Required to check optic cable routing
or vending.
Blink
Loopback test being performed.
Green
WiFi function enabled.
Off
WiFi function disabled.
On
In progress.
Success (for 5 seconds)
② LAN1~4
Connect PC or LAN.
Off
Disabled or process finished.
On
The 1G port link is up.
Connect power adapter.
Turn on/off the unit.
⑤ RESET
Reboot the unit.
⑥ WPS
Enable WPS process.
⑦ WLAN
Enable WiFi function.
Green
LAN
1~4
Blink
On
Orange
Off
① Remove the protective cap of GPON port.
② Connect an SC/UPC connector optic cable to the port.
③ And then arrange optic line on splice tray, not to give damage to
GPON connection due to any possible pull.
System Memory
128MB DDR3
Flash Memory
128MB Nand Flash
Uplink Interface
1 GPON port (1G, SC/UPC)
Service Interface
4 10/100/1000Base-T ports (RJ45)
Wireless
Internal antenna
IEEE 802.11b/g/n compliant
Bandwidth: 2.4GHz
Two Transmit and Two Receive path (2T2R)
LED
PWR, PON, ALM, WLAN, WPS, LAN1~4
Power Adapter
Output: 12VDC/1A
Operating Temp.
0 to 40°C
Operating Humidity
5 to 95% (non-condensing)
Dimensions
(W x D x H)
160 x 125 x 43 mm
Button
ON/OFF power, WLAN, WPS, RESET
Blink
④
⑤
⑥
⑦
Connect the Ethernet cable from LAN port to PC.
Connect a power adapter from power port to a live AC outlet.
Turn on the unit by pushing the power button.
Push WLAN button to enable WiFi.
GPON Port
ONT normally operating.
On
Connect the network.
③ Power Port
● Caution
Any changed or modifications not expressly approved by the party responsible for
compliance could void the user`s authority to operate this equipment.
● FCC RF exposure requirements
The antenna used with this module must be installed to provide a separation distance of
at least 20cm from all persons, and must not transmit simultaneously with any other
antenna or transmitter except in accordance with FCC multi-transmitter product
procedures.
● User Information
This device complies with Part 15 of the FCC`s Rule. Operation is subject to the following
to conditions;
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specification
Firmware being downloaded. Do not turn off the unit.
① OPTIC LINE
④ ON/OFF
Item
Service held after registered normally.
Blink
Blink
Description
Description
The system is turned on.
Off
Item
2.2 Specification
3. Installation
On
On
Orange
H660W
Power Adapter
RJ45 UTP Cable (CAT5e)
QIG (Quick Guide)
www.dasannetworks.com/en
2.4 Front View (LEDs)
2.3 Rear View
2.1 Package Contents
FCC Certification Requirements
③ Open a web browser, and enter http://192.168.1.100:8080 in a
URL field.
④ Type “user/user” in user name/password field, and log into the
system. Initial page is displayed.
2. Introduction
The 1G transmit or receive activity is present
on the service port.
The 10/100M port link is up.
The 10/100M transmit or receive activity is present
on the service port.
Link is down.
Splice Tray

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Format                          : application/pdf
Title                           : [H660W_CHT]_QIG_EN_140828_V1
Metadata Date                   : 2014:08:28 16:34:14+09:00
Modify Date                     : 2014:08:28 16:34:14+09:00
Create Date                     : 2014:08:28 16:34:13+10:00
Creator Tool                    : Adobe Illustrator CS6 (Windows)
Thumbnail Width                 : 256
Thumbnail Height                : 184
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 20317 bytes, use -b option to extract)
Instance ID                     : uuid:3af6a327-a3f2-4187-ab65-511590dd60d4
Document ID                     : xmp.did:15B4ECB3852EE4119CC78AC5769D46B6
Original Document ID            : uuid:5D20892493BFDB11914A8590D31508C8
Rendition Class                 : proof:pdf
Derived From Instance ID        : uuid:d5b643de-f57b-4c6d-ac24-591eb6fef8ab
Derived From Document ID        : xmp.did:3098BE2BEF2CE411B1C1E4D50405C62C
Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8
Derived From Rendition Class    : proof:pdf
History Action                  : saved, saved
History Instance ID             : xmp.iid:A58105131412E411897AB04E426AEF0A, xmp.iid:15B4ECB3852EE4119CC78AC5769D46B6
History When                    : 2014:07:23 11:50:15+09:00, 2014:08:28 16:34:11+09:00
History Software Agent          : Adobe Illustrator CS6 (Windows), Adobe Illustrator CS6 (Windows)
History Changed                 : /, /
Startup Profile                 : Print
Has Visible Overprint           : False
Has Visible Transparency        : False
N Pages                         : 1
Max Page Size W                 : 430.388889
Max Page Size H                 : 310.444444
Max Page Size Unit              : Millimeters
Font Name                       : Arial-ItalicMT, Calibri, Calibri-Italic, Calibri-Bold, Calibri-BoldItalic, YDISwiriM, YDIYGO240, YDIYMjO110, YDIBirdM, Gulim, AdobeMyungjoStd-Medium, YDIYGO120
Font Family                     : Arial, Calibri, Calibri, Calibri, Calibri, -½¬¸®M, -À±°íµñ240, -윤명조110, -파랑새M, 굴림, Adobe 명조 Std, YDIYGO120 KSCpc-EUC-H
Font Face                       : Italic, Regular, Italic, Bold, Bold Italic, Regular, Regular, Regular, Regular, Regular, M, KSCpc-EUC-H
Font Type                       : Open Type, Open Type, Open Type, Open Type, Open Type, TrueType, TrueType, TrueType, TrueType, TrueType, Open Type, Unknown
Font Version                    : Version 5.20, Version 1.02, Version 1.02, Version 1.02, Version 1.02, Version 1.00, Version 2.00, Version 5.01, Version 1.012;PS 1.004;hotconv 1.0.67;makeotf.lib2.5.33168, Version 5.01
Font Composite                  : False, False, False, False, False, False, False, False, False, False, False, False
Font File Name                  : ariali.ttf, CALIBRI_0.TTF, CALIBRII_0.TTF, CALIBRIB_0.TTF, CALIBRIZ_0.TTF, , , ymjo110.ttf, 파랑새m.ttf, gulim.ttc, AdobeMyungjoStd-Medium.otf, gulim.ttc
Plate Names                     : Cyan, Magenta, Yellow, Black, PANTONE 647 CVC, 100.65.5.45
Swatch Groups Colorants Tint    : 100.000000
Swatch Groups Group Name        : 밝기
Swatch Groups Group Type        : 1
Swatch Groups Colorants Swatch Name: C=60 M=90 Y=0 K=0
Swatch Groups Colorants Mode    : CMYK
Swatch Groups Colorants Type    : PROCESS
Swatch Groups Colorants Cyan    : 60.000004
Swatch Groups Colorants Magenta : 90.000000
Swatch Groups Colorants Yellow  : 0.003099
Swatch Groups Colorants Black   : 0.003099
Producer                        : Adobe PDF library 10.01
Page Count                      : 1
Creator                         : Adobe Illustrator(R) 16.0
For                             : kangth,
Bounding Box                    : -303 -1078 889 -224
Container Version               : 11
Creator Version                 : 16

EXIF Metadata provided by EXIF.tools