DATECS DATECSBTIOS Bluetooth Module User Manual DPP 450 UM EN Datecs

DATECS LTD. Bluetooth Module DPP 450 UM EN Datecs

UserManual.wiki >

DATECS >

DATECSBTIOS User Manual >

User manual 2 of 2

1. User manual 1 of 2
2. User manual 2 of 2

User manual 2 of 2

1 DATECS DPP-450 User manual 2 THE INFORMATION IN THIS DOCUMENT CANNOT BE REPRODUCED IN ANY MECHANICAL, ELECTRICAL OR ELECTRONIC WAY AND UNDER ANY CIRCUMSTANCES WITHOUT THE WRITTEN CONSENT FROM DATECS LTD. VERSION: June 2014

1 DATECS DPP-450 User manual 3 Legal Notice “Made for iPod,” “Made for iPhone,” and Made for iPad” mean that an electronic accesory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible fort he operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accesory with iPod, iPhone, or iPad may affect wireless performance. Compatability Made for iPhone 5 iPhone 5S iPhone 5C iPhone 4S iPhone 4 iPod touch (5th generation) iPod touch (4th generation) iPod touch (3rd generation) iPad (4th generation) iPad mini iPad (3rd generation) iPad 2 iPad, iPhone, iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Lightning is a trademark of Apple Inc.

1 DATECS DPP-450 User manual 4 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. CAUTION: Use shielded cables to connect this device to computers. Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

1 DATECS DPP-450 User manual 5 CONTENTS 1. Introduction............................................................................................................. 6 2. Features ................................................................................................................. 6 3. Technical specification............................................................................................ 7 4. General view........................................................................................................... 7 4.1 Dimensions and outlook ................................................................................. 10 4.2 Box Contents.................................................................................................. 11 5. Getting started ...................................................................................................... 12 5.1 Charge DPP-450 ............................................................................................ 13 5.2 Diagnostic information.................................................................................... 14 5.3 Loading paper ................................................................................................ 14 5.4 Mounting belt clip ........................................................................................... 18 5.5 Self-Test......................................................................................................... 18 5.6 Page Mode ..................................................................................................... 20 5.7 Ruled lines...................................................................................................... 20 5.8 Protocol mode ................................................................................................ 20 5.9 Hardware setup .............................................................................................. 22 5.10 List of commands ......................................................................................... 26 5.11 Connecting Device ....................................................................................... 28 5.12 Mount Strap.................................................................................................. 30

1 DATECS DPP-450 User manual 8 LED Indication • Paper end or paper out • Cover open • Low battery • Print head overheating • Battery charging Audio Indications Electro-magnetic buzzer Display • LCD 128 x 64 dots • LED backlight Buttons • Power button • Print button • Feed button Memory 4MB Flash(option) Buffer Size up to 128 kB Periphery • RFID card reader: • MiFARE Mini • ISO 14443 • MiFARE Classic 1K / 4K • ISO 15693 • MiFARE Ultra-Light / Ultra-Light-C • FeliCa • MiFARE Plus 2K / 4K Emulation • ESC/POS • Eltron • ZEBRA* Power Supply AC Adapter • Input: AC: 100-240V~, 50/60Hz • Output: DC19V, 5.2A Battery Rechargeable Li-Ion battery 14.4V / 2200mAh Battery charge time – 2.5 hours Battery capacity per charge ~ 20 000 lines Reliability Thermal head life: 50km Mechanism(MCBF): 15 000 000 lines Weight, kg 0.785(w/o paper, include battery) 0.850 (with paper, include battery) Dimensions,(WxDxH) mm 157 x 138 x 67 Environmental • Operating: -15°C to +50°C / 30 to 85% RH • Storage: -20°C to +60°C / 10 to 90% RH

1 DATECS DPP-450 User manual 9 Drop Test Height: 1m 3 times on each of the 6 faces 3 times on each of the 4 edges OS compatibility iOS, Android OS, BlackBerry OS, Windows OS, Win CE, Windows Mobile, Windows Phone Accessories • Neck strap • Metal belt clip • Carrying case • Single battery charger

1 DATECS DPP-450 User manual 10 4. General view 4.1 Dimensions and outlook

1 DATECS DPP-450 User manual 11 4.2 Box Contents

1 DATECS DPP-450 User manual 12 Software (Drivers & SDK ): Because of the continually evolving Driver & SDK to support new mobile devices, Drivers & SDK are distributed online and is available for download at our website indicated below. For details on using the DPP-450 Drivers & SDK, please refer to the SDK’s documentation. http://www.datecs.bg/en/products/DPP-450/2/264# 5. Getting started The DPP-450 allows you to printer information from your PDA & Smart phone. Before using the DPP-450 thermal printer the battery should be properly charged. The following Quick Start guide will help to get your DPP-250 ready for use. Steps What to do Purpose Where to find more information 1 Charge the DPP-450 rechargeable battery pack as recommended in this manual The Lithium Ion battery pack should be fully charged before use to ensure long battery life. Charging Battery, Page 9 2.1 Load DPP-450 print media(Thermal paper roll) DPP-450 requires Thermal paper for printing. Loading Paper, Page 10 2.2 Load DPP-450 print media(Thermal label paper) DPP-450 requires Thermal label paper. Loading Paper, Page 10 3 Setup Bluetooth Paring Setup Bluetooth pairing to allow DDP-450 to communicate with Bluetooth devices. Bluetooth Setup, Page 24 4 Install DPP-450 Software To print information from your device, software needs to be installed onto your device. Install DPP-450 Software, Page 8

1 DATECS DPP-450 User manual 13 5.1 Charge DPP-450 The DPP-450 uses a Lithium-Ion rechargeable battery pack. To prevent electrical damage to the DPP-450 and/or battery pack, please use approved AC Charger only. Charging time is 3 hours from empty to full charge. When the battery is fully charged the device can print 150m paper roll, this is 3.5 rolls standart for DPP-450. AC adapter and power cord Battery DPP-450 and battery DPP-450 DC jack

1 DATECS DPP-450 User manual 14 Insert cable to dc jack to start charging. When the device is turn on(holding turn on/off button), in display will show “CHG” text and greed led “CHARGE” is blink. 5.2 Diagnostic information • Holding <LF> button while power on for ~ 0.5 sec (first sound signal) – short self-test. • Holding <LF> button while power on for ~ 2.5 sec (second sound signal) – start dump mode. All input data are printed hexadecimal and as text. • Holding <LF> button while power on for more than 8.5 sec (fifth 4-tone sound signal) – enter firmware updating mode. • Holding <ON/OFF> button while power on for ~ 4 sec (first sound signal): - If serial cable is connected (RS232 communication) – temporary forcing 9600 bps serial speed. - If no serial cable connected (Bluetooth or USB communication) – starting a hardware menu for fast Bluetooth pairing info reset. • Holding <ON/OFF> button while power on for more than 6 sec – enter hardware setup mode. • Holding <ON/OFF> button while power off for more than ~ 1sec. • Holding <ON/OFF> button while less than ~ 1sec, backlight is turn on for short time. • Holding <ON/OFF> button and press <LF> button – printing WIFI info. 5.3 Loading paper First slide peeler to position show on the picture. After this push to open paper cover. ECS/POS Ready CHG Peeler(slide back) Push to open paper cover

1 DATECS DPP-450 User manual 15 When the paper cover is open drop the new roll of thermal media. With green lever can choose size of thermal paper. To choose paper size – pull up lever and push on right for small paper or left for big. When lever is in max. left position insert new paper(if size is different from last one) and pull up lever and push right until reach paper, then release lever. Insert new paper Lever for paper size

1 DATECS DPP-450 User manual 16 Right paper position Close paper cover

1 DATECS DPP-450 User manual 17 Slide peeler Peeler setting for label paper. Peeler setting for paper roll.

1 DATECS DPP-450 User manual 18 5.4 Mounting belt clip Using two screws. 5.5 Self-Test • Holding <LF> button while power on for ~ 0.5 sec (first sound signal) – short self-test. The DPP-450 has a built-in test pattern that shows the printer’s current configuration as well as the various resident printer fonts. The self-test can also be used as a troubleshooting tool to determine printing problems or battery level. The steps below show how the self-test is printed activated.

1 DATECS DPP-450 User manual 19 • Holding <LF> button while power on for ~ 5.5 sec (third sound signal) – self-test.  Resident font sizes  Characters per line  Text formatting  Resident character set  Resident barcode symbols  Printer’s configuration

1 DATECS DPP-450 User manual 20 5.6 Page Mode In page mode the result of incoming commands is forwarded to a reserved memory area (page). The page place and size is defined using command ESC W. Command GS T selects the print direction in this page. At the end the collected information is printed using one of the commands, provided for this. Commands ESC FF and GS FF print only the currently defined page, but command ESC Z prints the area between the first and last line containing at least one black point. All commands except GS L and GS W work in page mode. The centering and right alignment (command ESC a) is working in the currently defined page width. 5.7 Ruled lines The printer has two line buffers with size the maximum printing width (paper width in standard mode or the selected page width in page mode). When ruled lines are active, then every horizontal line of the text line is combined with the selected ruled line buffer. Bit ‘1’ in the ruled line buffer is a black dot in OR mode and inverts the color of the dot in XOR mode. Two commands allow the ruled line buffers to be printed without combining with a text line. When pressing the FEED button, no ruled lines buffer is applied. All ruled lines commands start with symbol DC3 (ASCII code 13h). Please see command DC2 = , too . Warning! The ruled lines print position depends not on GS L and GS W (left margin and line width) and is always at the beginning of the line (or at the beginning of the printable area in page mode). The printed text and graphic change their position according these commands. When printing 180 degrees rotated lines (command ESC { 1) ruled lines buffers are not rotated! 5.8 Protocol mode Protocol mode is active when hardware switch 11 is on. The purpose of this mode is to give stronger real time access to the printer. All input data are sent in packets as described below. The printer returns an answer to the packet immediately. Output packet format: Channel Command LenHi LenLo Data Answer format: Channel Status LenHi LenLo Data Channel: One byte: Bits 0 – 6 Channel number (Device type) Bit 7 0: Send data; 1: Response Command: One byte with possible value: 0: Open channel (No action – all channels always open) 1: Close channel (No action – all channels always open)

1 DATECS DPP-450 User manual 21 2: Send data 3: Request data >4: Application specific Status: One byte: 0 1 Bit 0 No error Error occured Bit 1 ACK (Packet accepted) NACK (Packed not accepted) Bit 2 Channel and command OK Wrong channel or command Bit 3 Battery OK Low battery Bit 4 Printing head OK Printing head too hot Bit 5 Paper OK Out of paper Bit 6 Not defined Bit 7 Printer ready Printer busy Bit 7 is set, if: • There are unprinted lines in the print buffer. • There are bytes in the print buffer. • The printer is executing a macro. • The printer is executing selftest. • The button <LF> is pressed – feeding paper. LenHi: High byte of data length of data. 00h to 08h. LenLo: Low byte of data length of data. 00h to FFh. Data: 256*LenHi +LenLo data bytes. The maximum packet length is 2048 bytes. The answer differs from the command by bit 7 (MSB) in the channel number. If bit 7 is 0 then it is a command, if it is 1 then it is a response. Bit 0 in the status byte shows if there was an error accepting or processing the data block. If this bit is 1 the other bits show the type of the error. The printer never issues a transmission by itself. It always responds as an answer to a command. The communication goes like this: Host – command, Printer – answer; Host – command, Printer – answer; etc. The defined channels are: 1 Printer. 16 (10h) Optional card reader. Commands for the printer channel (1): Command 2 Send data The data is copied into the printer’s print buffer. If there’s not enough space into the print buffer the packet is rejected, and a status byte with value 3 is returned in the answer. Command 3 Receive data If there is data to be transmitted from the printer to the host, it is transmitted in the data field of the packet, otherwise an empty packet is received. The application must take care to get the data fast enough from the output buffer or the data may be corrupt.

1 DATECS DPP-450 User manual 22 Command 4 Get printer status. 5 data bytes returned in response: BufferHi BufferLo PrStatus Volt Temperature BufferHi High byte of the count of free bytes in input buffer. BufferLo Low byte of the count of free bytes in input buffer. PrStatus Printer status. The following bits defined: Bit 0 Battery low Bit 1 Too hot Bit 2 No paper Volt The battery voltage in units 0.1V Temperature The head temperature in degrees Celsius. If free bytes in input buffer are more than 65535 (FFFFh), then FFFFh is returned. Using channel 16 is the only way for full control over the optional card reader. Communication example (all bytes hexadecimal): Send data: >>> 01 02 00 05 11 22 33 44 55 <<< 81 00 00 00 Send data with error: >>> 01 02 00 05 11 22 33 44 55 <<< 81 01 00 00 >>> 01 02 00 05 11 22 33 44 55 <<< 81 01 00 00 >>> 01 02 00 05 11 22 33 44 55 <<< 81 00 00 00 Receive data: >>> 01 03 00 00 <<< 81 00 00 00 >>> 01 03 00 00 <<< 81 00 00 04 11 22 33 44 >>> 01 03 00 00 <<< 81 00 00 00 Get status: >>> 01 04 00 00 <<< 81 00 00 05 3F F8 01 49 27 5.9 Hardware setup Holding <ON/OFF>button while power on for more than 6sec. – enter hardware setup mode. “STATUS”(red led) will blink once, after this device is printing message:

1 DATECS DPP-450 User manual 23 Then press FEED button, to enter Hardware menu. Device will prining current settings. The LCD in hardware configuration menu: With button “PRINT” can move down and with “FEED” can enter in selected. Hardware menu tree: FACTORY DEFAULT MEM. SWITCHES: BAUD RATE: IrDA BAUD RATE:

1 DATECS DPP-450 User manual 24 FACTORY DEFAULT YES NO MEM. SWITCHES ENABLE SOUND Enable/Disable printer's buzzer EXECUTE <CR> AS <LF> Disable CR/CR is executed as LF DISABLE <LF> COMMAND Enable/Disable LF DISABLE<LF>AFTER Disable LF immediately after CR DEFAULT SMALL FONT Set the small font as default USE GAP SENSOR Enable/Disable the GAP sensor BLACK MARK MODE Enable/Disable the black mark sensor XON/XOFF Enable/Disable XON/XOFF protocol ENABLE USB INTERFACE Enable/Disable USB communication port USB IN DEVICE MODE Changing the USB HOST/DEVICE mode PROTOCOL MODE Enable/Disable Protocol mode DISABLE BLUETOOTH Enable/Disable Bluethooth communication DEFAULT SELECT DISP Set the main display as default DISABLEDISCOVERABILITY Enable/Disable printer's discoverability LCD FOREIGN LANGUAGE DISCARD Exit without saving configuration ACCEPT Exit with saving configuration BAUDRATE Changing the printer communication speed (RS) • 115200 bps • 38400 bps • 31200 bps • 2400 bps • 4800 bps • 9600 bps • 19200 bps • 57600 bps IrDA BAUD RATE Changing the IrDA communication speed • 19200 bps • 9600 bps • 38400 bps • 57600 bps • 115200 bps AUTO OFF TIME Changing the printer's auto OFF time • 10 min. • 15 min. • 20 min. • 30 min. • 45 min. • 60 min. • 0 min

1 DATECS DPP-450 User manual 25 • 2 min. • 5 min. PRINT DARKNESS Changing the printing darkness • 120 % • 140 % • 160 % • 60 % • 75 % • 90 % • 100 % CHARACTER TABLE Changing the printer's character table • Western (1252) • CE (1250) • Turkish (1254) • Baltic (1257) • Cyrillic (1251) • Greek (1253) • Hebrew ( 1255) • Katakana • Arabic • Arabic (1256) • Arabic (1256A) • Arabic (1256F) • Thai (874) • VISCII • English (437) • Latin 1 (850) • Portuguese (860) • Lithuanian • Latin 2 (852) • Polish • Turkish (857) • Baltic (775) • Bulgarian (856) • Russian (866) • Latvian • Greek (737) • Hebrew (862) PAIRING INFO Resetting pairing info // Enable/Disable saving pairing info • Disable authentication • Change pairing info • Save pairing info

1 DATECS DPP-450 User manual 26 USB DEV. CLASS Changing the USB device class of the printer Printer/Serial • Printer • Serial SAVE & EXIT MENU 5.10 List of commands 1 BEL Sounds the buzzer 2 HT Horizontal Tab command configuration flags 2, 3 and 4 3 LF Printing а line and Paper Feeding command 4 FF Printing and paper feeding to the black mark position 5 CR The operation of the command depends on the state of the 6 DC2 = Image LSB/MSB select 7 DC3 ( DC3 (Ruled line) commands sequence start 8 DC3 + Sets the ruled line ON 9 DC3 - Sets the ruled line off 10 DC3 A Selects ruled line A 11 DC3 B Selects ruled line B 12 DC3 C Clears selected ruled line buffer 13 DC3 D Sets a single dot in selected ruled line buffer 14 DC3 F Ruled line pattern set 15 DC3 L Ruled line line set 16 DC3 M Selects ruled line combine mode 17 DC3 P Ruled line 1 dot line print 18 DC3 p Ruled line n dots line print 19 DC3 v Ruled line image write 20 CAN Canceling print data in page mode 21 ESC FF Printing data in page mode 22 ESC RS Sounds the buzzer 23 ESC SP Setting character spacing 24 ESC # Setting EURO symbol position 25 ESC $ Specifying the absolute horizontal position of printing 26 ESC % Selecting/Canceling the printing of downloaded user character sets 27 ESC & Selecting user character set 28 ESC ! Specifying printing mode of text data 29 ESC * Printing graphical data 30 ESC + Switchs OFF the printer 31 ESC - Selecting/Canceling underlining 32 ESC . Printing self test/diagnostic information 33 ESC 2 Specifying 1/6-inch line feed rate 34 ESC 3 Specifying line feed rate n/203 inches 35 ESC < Changes print direction to opposite 36 ESC = Data input control 37 ESC > Selecting print direction 39 ESC @ Initializing the printer 40 ESC CAL Black mark mode sensor calibration

$1 DATECS DPP-450 User manual 27 41 ESC D Setting horizontal tab position 42 ESC E Specifying/Canceling highlighting 43 ESC F Filling or inverting the page area in page mode 44 ESC G Specifying/Canceling highlighting 45 ESC I Specifying/Canceling Italic print 46 ESC J Printing and Paper feed n/203 inches 47 ESC L Selecting page mode 48 ESC N Reading programmed serial number 49 ESC R Selecting country 50 ESC S Specifying speed (bps) of the serial port 51 ESC T Printing short self test 52 ESC U Selecting/Canceling underlined printing 53 ESC V Selecting/Canceling printing 90°- right turned characters 54 ESC W Defining the print area in page mode 55 ESC X Specifying max printing speed 56 ESC Y Selecting intensity level 57 ESC Z Returning diagnostic information 58 ESC \ Specifying relative horizontal position 59 ESC ] Loading the default settings stored in Flash memory 60 ESC ^ Saving current settings in Flash memory 61 ESC _ Loading factory settings 62 ESC ` Reading the Battery Voltage and Thermal head temperature 63 ESC a Aligning the characters 64 ESC b Increasing text line height 65 ESC c5 Enabling/Disabling the functioning of the button LF 66 ESC d Printing and feeding paper by n- lines 67 ESC i Feeding paper backwards 68 ESC o Temporarily feeding paper forward 69 ESC pair= Enabling/Disabling PAIRING info saving in Bluetooth mode 70 ESC pwd= Programming a new Bluetooth password (PIN) 71 ESC r Full command for sounding buzzer 72 ESC s Reading printer settings 73 ESC u Selecting code table 74 ESC v Transmitting the printer status 75 ESC x Setting the time interval for automatically switching Off the printer 76 ESC y Setting USB response strings 77 ESC { Enabling/Canceling printing of 180° turned characters 78 GS FF Printing in page mode and returning to standard mode 79 GS $ Specifying the absolute vertical position in page mode 80 GS ) Setting printer flags (memory switches) 81 GS * Defining a Downloaded Bit Image (logo) 82 GS / Printing a Downloaded Bit Image 83 GS : Starting/ending macro definitions 84 GS B Enabling/Disabling inverse printing (white on black) 85 GS C Read the Real Time Clock 86 GS H Selecting printing position of HRI Code 87 GS L Setting the left margin 88 GS Q Printing 2-D barcodes$

$1 DATECS DPP-450 User manual 28 89 GS R Filling or inverting a rectangle in page mode 90 GS S Selecting 2-D barcode cell size 91 GS T Selecting the print direction in page mode 92 GS U Selecting standard mode 93 GS W Setting the print area width 94 GS X Drawing a rectangular box with selected thickness in page mode 95 GS Z Printing the non blank page area only in page mode 96 GS \ Specifying the relative vertical position in page mode 97 GS ^ Executing macro 98 GS c Setting the Real Time Clock 99 GS f Setting the font of HRI characters of the barcode 100 GS h Setting the height of the barcode 101 GS k Printing a barcode 102 GS p Settings for 2D barcode PDF417 103 GS q Selecting the height of the module of 2D barcode PDF417 104 GS w Selecting the horizontal size (Scale factor) of the barcode 105 GS x Direct text print in page mode 106 FS ! Specifying printing mode of two-byte text data 107 FS & Selecting two-byte text mode (JIS or GB2312) 108 FS - Selecting/Canceling underline mode for two-byte text mode 109 FS . Canceling two-byte text mode 110 FS C Selecting Shift-JIS mode (Japanese version only) 111 FS S Specifying character spacing for two-byte text mode 112 FS W Selecting double size characters for two-byte text mode 113 ESC y WAN WAN 5.11 Connecting Device The DPP-450 is designed to use different methods of communications. Care must be taken to ensure that the DPP-450 USB/RS 232 connector and PDA & Smartphone connector are not accidentally damaged. The figures below show how to attach the different device to the DPP-450. USB ( Cabled ) Version: Connect the DPP-450 using Mini USB cable is shown in the figure below. USB/RS 232 connector$

DATECS DATECSBTIOS Bluetooth Module User Manual DPP 450 UM EN Datecs

DATECS LTD. Bluetooth Module DPP 450 UM EN Datecs

Contents

User manual 2 of 2

Navigation menu

Namespaces

Views

Navigation