DATECS DATECSBTIOS Bluetooth Module User Manual DPP 450 UM EN Datecs

Download:
Mirror Download [FCC.gov]
Document ID	2335289
Application ID	T5Y7TSx/dL9pdpkehdKHYg==
Document Description	User manual 2 of 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	196.12kB (2451534 bits)
Date Submitted	2014-07-25 00:00:00
Date Available	2015-01-20 00:00:00
Creation Date	2014-07-23 15:25:46
Producing Software	Nitro PDF PrimoPDF
Document Lastmod	2014-07-23 15:25:46
Document Title	Microsoft Word - DPP-450_UM-EN_Datecs.doc.doc
Document Creator	PrimoPDF http://www.primopdf.com
Document Author:	nuncho

User Manual
ESC/POS PRINTER DPP-450
1 DATECS DPP-450
User manual
THE INFORMATION IN THIS DOCUMENT CANNOT BE REPRODUCED IN ANY MECHANICAL, ELECTRICAL
OR ELECTRONIC WAY AND UNDER ANY CIRCUMSTANCES WITHOUT THE WRITTEN CONSENT FROM DATECS LTD.
VERSION: June 2014
1 DATECS DPP-450
User manual
Legal Notice
“Made for iPod,” “Made for iPhone,” and Made for iPad” mean that an electronic accesory has been
designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the
developer to meet Apple performance standards. Apple is not responsible fort he operation of this
device or its compliance with safety and regulatory standards. Please note that the use of this
accesory with iPod, iPhone, or iPad may affect wireless performance.
Compatability
Made for
iPhone 5
iPhone 5S
iPhone 5C
iPhone 4S
iPhone 4
th
iPod touch (5 generation)
th
iPod touch (4 generation)
rd
iPod touch (3 generation)
iPad (4th generation)
iPad mini
iPad (3rd generation)
iPad 2
iPad, iPhone, iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Lightning is a
trademark of Apple Inc.
1 DATECS DPP-450
User manual
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Use shielded cables to connect this device to computers.
Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority
to operate the equipment.
1 DATECS DPP-450
User manual
CONTENTS
1. Introduction............................................................................................................. 6
2. Features ................................................................................................................. 6
3. Technical specification............................................................................................ 7
4. General view........................................................................................................... 7
4.1 Dimensions and outlook ................................................................................. 10
4.2 Box Contents.................................................................................................. 11
5. Getting started ...................................................................................................... 12
5.1 Charge DPP-450 ............................................................................................ 13
5.2 Diagnostic information .................................................................................... 14
5.3 Loading paper ................................................................................................ 14
5.4 Mounting belt clip ........................................................................................... 18
5.5 Self-Test ......................................................................................................... 18
5.6 Page Mode ..................................................................................................... 20
5.7 Ruled lines...................................................................................................... 20
5.8 Protocol mode ................................................................................................ 20
5.9 Hardware setup .............................................................................................. 22
5.10 List of commands ......................................................................................... 26
5.11 Connecting Device ....................................................................................... 28
5.12 Mount Strap.................................................................................................. 30
1 DATECS DPP-450
User manual
1. Introduction
DATECS DPP-450 is a mobile ESC/POS and LABEL thermal printer. It can be
used in dynamic working conditions and its abundant built-in features allow it to be
widely used for different applications. Printer can quickly and easily print text and/or
graphics, depending on customer’s needs – barcodes, logo, etc.
2. Features
The DPP-450 is a mobile line thermal printer, applicable for different applications
as shown below:
• Mobile
• Label Peeler
• traveling sales
• Retail
• Transportation
• Receipts
• Point of sales
• Distribution
1 DATECS DPP-450
User manual
3. Technical specification
Printing Method
Direct line thermal
Print Width
104mm, 832 dots/line
Dot Density
8 x 8 dots/mm (203 dpi x 203 dpi)
Print Speed
150mm/sec max
Fonts
Resident Fonts:
Font A: 48 characters/line
Font B: 64 characters/line
Graphic Logo
1 x Black & White , Size: 832 x 248 dots
Barcode Types
1D: EAN 13, EAN 8, UPC A, UPC E, Code 39, Code 93, Code 128,
Codabar, 2 of 5 interleaved,
2D: PDF417, QR code
Paper spec:
• Width: 50-115mm
• Paper roll: φ58mm or less
• Thickness: 59-154µm
Paper Loading
Easy paper loading
Paper Feed System
Step
Paper Type
Label/Receipt
Paper sensor
• PE sensor
• BM sensor
• Label Gap sensor
Post Printing Paper
Treatment
Peeler for Labels
Cutter for Receipts
Connectivity
• RS-232C – max 115200bps
• mini USB 2.0 (only device)
• BT 2.0 Class 2 (option)
- SPP - Serial Port Profile
• BT 3.0 Class 2 (option)
- SPP - Serial Port Profile
- iAP - iPod Accessory Protocol
• Wi-Fi 802.11b (option)
- BSS and IBSS network mode
• IrDA
Loadable Fonts:
Font C: 48 characters/line
Font D: 64 characters/line
1 DATECS DPP-450
User manual
LED Indication
• Paper end or paper out
• Cover open
• Low battery
• Print head overheating
Audio Indications
Electro-magnetic buzzer
Display
• LCD 128 x 64 dots
• LED backlight
Buttons
• Power button
• Print button
• Feed button
Memory
4MB Flash(option)
Buffer Size
up to 128 kB
Periphery
• RFID card reader:
• MiFARE Mini
• MiFARE Classic 1K / 4K
• MiFARE Ultra-Light / UltraLight-C
Emulation
• ESC/POS
• Eltron
• ZEBRA*
Power Supply
AC Adapter
• Input: AC: 100-240V~, 50/60Hz
• Output: DC19V, 5.2A
Battery
Rechargeable Li-Ion battery 14.4V / 2200mAh
Battery charge time – 2.5 hours
Battery capacity per charge ~ 20 000 lines
Reliability
Thermal head life: 50km
Mechanism(MCBF): 15 000 000 lines
Weight, kg
0.785(w/o paper, include battery)
0.850 (with paper, include battery)
Dimensions,(WxDxH) mm
157 x 138 x 67
Environmental
• Operating: -15°C to +50°C / 30 to 85% RH
• Storage: -20°C to +60°C / 10 to 90% RH
• Battery charging
• ISO 14443
• ISO 15693
• FeliCa
• MiFARE Plus 2K / 4K
1 DATECS DPP-450
User manual
Drop Test
Height: 1m
3 times on each of the 6 faces
3 times on each of the 4 edges
OS compatibility
iOS, Android OS, BlackBerry OS, Windows OS, Win CE, Windows
Mobile, Windows Phone
Accessories
• Neck strap
• Metal belt clip
• Carrying case
• Single battery charger
1 DATECS DPP-450
User manual
4. General view
4.1 Dimensions and outlook
10
1 DATECS DPP-450
User manual
4.2 Box Contents
11
1 DATECS DPP-450
User manual
Software (Drivers & SDK ):
Because of the continually evolving Driver & SDK to support new mobile devices,
Drivers & SDK are distributed online and is available for download at our website
indicated below. For details on using the DPP-450 Drivers & SDK, please refer to the
SDK’s documentation.
http://www.datecs.bg/en/products/DPP-450/2/264#
5. Getting started
The DPP-450 allows you to printer information from your PDA & Smart
phone. Before using the DPP-450 thermal printer the battery should be properly
charged. The following Quick Start guide will help to get your DPP-250 ready
for use.
Steps
2.1
2.2
What to do
Charge the DPP-450
rechargeable battery
pack as
recommended in this
manual
Load DPP-450 print
media(Thermal paper
roll)
Load DPP-450 print
media(Thermal label
paper)
Setup Bluetooth
Paring
Install DPP-450
Software
Purpose
The Lithium Ion battery
pack should be fully
charged before use to
ensure long battery life.
Where to find more
information
Charging
Battery,
Page 9
DPP-450 requires Thermal
paper for printing.
Loading Paper, Page
10
DPP-450 requires Thermal
label paper.
Loading Paper, Page
10
Setup Bluetooth pairing to
allow DDP-450 to
communicate with
Bluetooth devices.
To print information from
your device, software
needs to be installed onto
your device.
Bluetooth
Page 24
12
Setup,
Install
DPP-450
Software, Page 8
1 DATECS DPP-450
User manual
5.1 Charge DPP-450
The DPP-450 uses a Lithium-Ion rechargeable battery pack.
To prevent electrical damage to the DPP-450 and/or battery pack, please use
approved AC Charger only.
Charging time is 3 hours from empty to full charge. When the battery is fully
charged the device can print 150m paper roll, this is 3.5 rolls standart for DPP-450.
AC adapter and power cord
Battery
DPP-450 and battery
DPP-450 DC jack
13
1 DATECS DPP-450
User manual
Insert cable to dc jack to start charging.
When the device is turn on(holding turn on/off button), in display will show “CHG”
text and greed led “CHARGE” is blink.
ECS/POS Ready
CHG
5.2 Diagnostic information
• Holding  button while power on for ~ 0.5 sec (first sound signal) – short selftest.
• Holding  button while power on for ~ 2.5 sec (second sound signal) – start
dump mode. All input data are printed hexadecimal and as text.
• Holding  button while power on for more than 8.5 sec (fifth 4-tone sound
signal) – enter firmware
updating mode.
• Holding  button while power on for ~ 4 sec (first sound signal):
- If serial cable is connected (RS232 communication) – temporary forcing 9600
bps serial
speed.
- If no serial cable connected (Bluetooth or USB communication) – starting a
hardware menu
for fast Bluetooth pairing info reset.
• Holding  button while power on for more than 6 sec – enter hardware
setup mode.
• Holding  button while power off for more than ~ 1sec.
• Holding  button while less than ~ 1sec, backlight is turn on for short time.
• Holding  button and press  button – printing WIFI info.
5.3 Loading paper
Peeler(slide back)
First slide peeler to position
show on the picture. After this
push to open paper cover.
Push to open
paper cover
14
1 DATECS DPP-450
User manual
When the paper cover is open
drop the new roll of thermal media. With
green lever can choose size of thermal
paper.
To choose paper size – pull up
lever and push on right for small paper
or left for big. When lever is in max. left
position insert new paper(if size is
different from last one) and pull up lever
and push right until reach paper, then
release lever.
Lever for paper size
Insert new paper
15
1 DATECS DPP-450
User manual
Right paper position
Close paper cover
16
1 DATECS DPP-450
User manual
Slide peeler
Peeler setting for label
paper.
Peeler setting for paper roll.
17
1 DATECS DPP-450
User manual
5.4 Mounting belt clip
Using two screws.
5.5 Self-Test
• Holding  button while power on for ~ 0.5 sec (first sound signal) – short selftest.
The DPP-450 has a built-in test
pattern that shows the printer’s current
configuration as well as the various
resident printer fonts. The self-test can
also be used as a troubleshooting tool to
determine printing problems or battery
level. The steps below show how the
self-test is printed activated.
18
1 DATECS DPP-450
User manual
• Holding  button while power on for ~ 5.5 sec (third sound signal) – self-test.

 Resident font sizes

 Characters per line

 Text formatting

 Resident character set

 Resident barcode symbols

 Printer’s configuration
19
1 DATECS DPP-450
User manual
5.6 Page Mode
In page mode the result of incoming commands is forwarded to a reserved
memory area (page). The page place and size is defined using command ESC W.
Command GS T selects the print direction in this page. At the end the collected
information is printed using one of the commands, provided for this. Commands ESC
FF and GS FF print only the currently defined page, but command ESC Z prints the
area between the first and last line containing at least one black point.
All commands except GS L and GS W work in page mode. The centering and
right alignment
(command ESC a) is working in the currently defined page width.
5.7 Ruled lines
The printer has two line buffers with size the maximum printing width (paper
width in standard mode or the selected page width in page mode). When ruled lines
are active, then every horizontal line of the text line is combined with the selected
ruled line buffer. Bit ‘1’ in the ruled line buffer is a black dot in OR mode and inverts
the color of the dot in XOR mode. Two commands allow the ruled line buffers to be
printed without combining with a text line.
When pressing the FEED button, no ruled lines buffer is applied.
All ruled lines commands start with symbol DC3 (ASCII code 13h). Please see
command DC2 = , too .
Warning!
The ruled lines print position depends not on GS L and GS W (left margin
and line width) and is always at the beginning of the line (or at the beginning of
the printable area in page mode). The printed text and graphic change their
position according these commands.
When printing 180 degrees rotated lines (command ESC { 1) ruled lines
buffers are not rotated!
5.8 Protocol mode
Protocol mode is active when hardware switch 11 is on. The purpose of this
mode is to give stronger real time access to the printer. All input data are sent in
packets as described below. The printer returns an answer to the packet
immediately.
Output packet format: Channel Command LenHi LenLo Data
Answer format:
Channel Status LenHi LenLo Data
Channel:
One byte:
Bits 0 – 6 Channel number (Device type)
Bit 7
0: Send data; 1: Response
Command: One byte with possible value:
0:
Open channel (No action – all channels always open)
1:
Close channel (No action – all channels always open)
20
1 DATECS DPP-450
User manual
2:
Send data
3:
Request data
>4:
Application specific
Status:
One byte:
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
No error
Error occured
ACK (Packet accepted)
NACK (Packed not accepted)
Channel and command OK
Wrong channel or command
Battery OK
Low battery
Printing head OK
Printing head too hot
Paper OK
Out of paper
Not defined
Printer ready
Printer busy
Bit 7 is set, if:
• There are unprinted lines in the print buffer.
• There are bytes in the print buffer.
• The printer is executing a macro.
• The printer is executing selftest.
• The button  is pressed – feeding paper.
LenHi:
LenLo:
Data:
High byte of data length of data. 00h to 08h.
Low byte of data length of data. 00h to FFh.
256*LenHi +LenLo data bytes.
The maximum packet length is 2048 bytes.
The answer differs from the command by bit 7 (MSB) in the channel number. If
bit 7 is 0 then it is a command, if it is 1 then it is a response. Bit 0 in the status
byte shows if there was an error accepting or processing the data block. If this bit
is 1 the other bits show the type of the error.
The printer never issues a transmission by itself. It always responds as an
answer to a command. The communication goes like this:
Host – command, Printer – answer; Host – command, Printer – answer; etc.
The defined channels are:
Printer.
16 (10h)
Optional card reader.
Commands for the printer channel (1):
Command 2 Send data
The data is copied into the printer’s print buffer. If there’s not
enough space into the print buffer the packet is rejected, and a status
byte with value 3 is returned in the answer.
Command 3 Receive data
If there is data to be transmitted from the printer to the host, it is
transmitted in the data field of the packet, otherwise an empty packet
is received. The application must take care to get the data fast enough
from the output buffer or the data may be corrupt.
21
1 DATECS DPP-450
User manual
Command 4 Get printer status. 5 data bytes returned in response:
BufferHi BufferLo PrStatus Volt Temperature
BufferHi
High byte of the count of free bytes in input
buffer.
BufferLo
Low byte of the count of free bytes in input
buffer.
PrStatus
Printer status. The following bits defined:
Bit 0
Battery low
Bit 1
Too hot
Bit 2
No paper
Volt
The battery voltage in units 0.1V
Temperature The head temperature in degrees Celsius.
If free bytes in input buffer are more than 65535 (FFFFh), then
FFFFh is returned.
Using channel 16 is the only way for full control over the optional card
reader.
Communication example (all bytes hexadecimal):
Send data:
>>> 01 02 00 05 11 22 33 44 55
<<< 81 00 00 00
Send data with error:
>>> 01 02 00 05 11 22 33 44 55
<<< 81 01 00 00
>>> 01 02 00 05 11 22 33 44 55
<<< 81 01 00 00
>>> 01 02 00 05 11 22 33 44 55
<<< 81 00 00 00
Receive data:
>>> 01 03 00 00
<<< 81 00 00 00
>>> 01 03 00 00
<<< 81 00 00 04 11 22 33 44
>>> 01 03 00 00
<<< 81 00 00 00
Get status:
>>> 01 04 00 00
<<< 81 00 00 05 3F F8 01 49 27
5.9 Hardware setup
Holding button while power on for more than 6sec. – enter
hardware setup mode. “STATUS”(red led) will blink once, after this device is printing
message:
22
1 DATECS DPP-450
User manual
Then press FEED button, to enter Hardware menu. Device will prining current
settings.
The LCD in hardware configuration menu:
FACTORY DEFAULT
MEM. SWITCHES:
BAUD RATE:
IrDA BAUD RATE:
With button “PRINT” can move down and with “FEED” can enter in selected.
Hardware menu tree:
23
1 DATECS DPP-450
User manual
FACTORY DEFAULT
YES
NO
MEM. SWITCHES
ENABLE SOUND
EXECUTE  AS 
DISABLE  COMMAND
DISABLEAFTER
DEFAULT SMALL FONT
USE GAP SENSOR
BLACK MARK MODE
XON/XOFF
ENABLE USB INTERFACE
USB IN DEVICE MODE
PROTOCOL MODE
DISABLE BLUETOOTH
DEFAULT SELECT DISP
DISABLEDISCOVERABILITY
LCD FOREIGN LANGUAGE
DISCARD
ACCEPT
BAUDRATE
•
•
•
•
•
•
•
•
Changing the printer communication speed (RS)
Changing the IrDA communication speed
19200 bps
9600 bps
38400 bps
57600 bps
115200 bps
AUTO OFF TIME
•
•
•
•
•
•
•
Exit without saving configuration
Exit with saving configuration
115200 bps
38400 bps
31200 bps
2400 bps
4800 bps
9600 bps
19200 bps
57600 bps
IrDA BAUD RATE
•
•
•
•
•
Enable/Disable printer's buzzer
Disable CR/CR is executed as LF
Enable/Disable LF
Disable LF immediately after CR
Set the small font as default
Enable/Disable the GAP sensor
Enable/Disable the black mark sensor
Enable/Disable XON/XOFF protocol
Enable/Disable USB communication port
Changing the USB HOST/DEVICE mode
Enable/Disable Protocol mode
Enable/Disable Bluethooth communication
Set the main display as default
Enable/Disable printer's discoverability
Changing the printer's auto OFF time
10 min.
15 min.
20 min.
30 min.
45 min.
60 min.
0 min
24
1 DATECS DPP-450
•
•
2 min.
5 min.
PRINT DARKNESS
•
•
•
•
•
•
•
User manual
Changing the printing darkness
120 %
140 %
160 %
60 %
75 %
90 %
100 %
CHARACTER TABLE Changing the printer's character table
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Western (1252)
CE (1250)
Turkish (1254)
Baltic (1257)
Cyrillic (1251)
Greek (1253)
Hebrew ( 1255)
Katakana
Arabic
Arabic (1256)
Arabic (1256A)
Arabic (1256F)
Thai (874)
VISCII
English (437)
Latin 1 (850)
Portuguese (860)
Lithuanian
Latin 2 (852)
Polish
Turkish (857)
Baltic (775)
Bulgarian (856)
Russian (866)
Latvian
Greek (737)
Hebrew (862)
PAIRING INFO
•
•
•
Resetting pairing info // Enable/Disable saving pairing info
Disable authentication
Change pairing info
Save pairing info
25
1 DATECS DPP-450
USB DEV. CLASS
•
•
User manual
Changing the USB device class of the printer Printer/Serial
Printer
Serial
SAVE & EXIT MENU
5.10 List of commands
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
BEL
HT
LF
FF
CR
DC2 =
DC3
DC3 +
DC3 DC3 A
DC3 B
DC3 C
DC3 D
DC3 F
DC3 L
DC3 M
DC3 P
DC3 p
DC3 v
CAN
ESC FF
ESC RS
ESC SP
ESC #
ESC $
ESC %
27
28
29
30
31
32
33
34
35
36
37
39
40
ESC &
ESC !
ESC *
ESC +
ESC ESC .
ESC 2
ESC 3
ESC <
ESC =
ESC >
ESC @
ESC CAL
Sounds the buzzer
Horizontal Tab command configuration flags 2, 3 and 4
Printing а line and Paper Feeding command
Printing and paper feeding to the black mark position
The operation of the command depends on the state of the
Image LSB/MSB select
( DC3 (Ruled line) commands sequence start
Sets the ruled line ON
Sets the ruled line off
Selects ruled line A
Selects ruled line B
Clears selected ruled line buffer
Sets a single dot in selected ruled line buffer
Ruled line pattern set
Ruled line line set
Selects ruled line combine mode
Ruled line 1 dot line print
Ruled line n dots line print
Ruled line image write
Canceling print data in page mode
Printing data in page mode
Sounds the buzzer
Setting character spacing
Setting EURO symbol position
Specifying the absolute horizontal position of printing
Selecting/Canceling the printing of downloaded user character
sets
Selecting user character set
Specifying printing mode of text data
Printing graphical data
Switchs OFF the printer
Selecting/Canceling underlining
Printing self test/diagnostic information
Specifying 1/6-inch line feed rate
Specifying line feed rate n/203 inches
Changes print direction to opposite
Data input control
Selecting print direction
Initializing the printer
Black mark mode sensor calibration
26
1 DATECS DPP-450
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
ESC D
ESC E
ESC F
ESC G
ESC I
ESC J
ESC L
ESC N
ESC R
ESC S
ESC T
ESC U
ESC V
ESC W
ESC X
ESC Y
ESC Z
ESC \
ESC ]
ESC ^
ESC _
ESC `
ESC a
ESC b
ESC c5
ESC d
ESC i
ESC o
ESC pair=
ESC pwd=
ESC r
ESC s
ESC u
ESC v
ESC x
76
77
78
79
80
81
82
83
84
85
86
87
88
ESC y
ESC {
GS FF
GS $
GS )
GS *
GS /
GS :
GS B
GS C
GS H
GS L
GS Q
User manual
Setting horizontal tab position
Specifying/Canceling highlighting
Filling or inverting the page area in page mode
Specifying/Canceling highlighting
Specifying/Canceling Italic print
Printing and Paper feed n/203 inches
Selecting page mode
Reading programmed serial number
Selecting country
Specifying speed (bps) of the serial port
Printing short self test
Selecting/Canceling underlined printing
Selecting/Canceling printing 90°- right turned characters
Defining the print area in page mode
Specifying max printing speed
Selecting intensity level
Returning diagnostic information
Specifying relative horizontal position
Loading the default settings stored in Flash memory
Saving current settings in Flash memory
Loading factory settings
Reading the Battery Voltage and Thermal head temperature
Aligning the characters
Increasing text line height
Enabling/Disabling the functioning of the button LF
Printing and feeding paper by n- lines
Feeding paper backwards
Temporarily feeding paper forward
Enabling/Disabling PAIRING info saving in Bluetooth mode
Programming a new Bluetooth password (PIN)
Full command for sounding buzzer
Reading printer settings
Selecting code table
Transmitting the printer status
Setting the time interval for automatically switching Off the
printer
Setting USB response strings
Enabling/Canceling printing of 180° turned characters
Printing in page mode and returning to standard mode
Specifying the absolute vertical position in page mode
Setting printer flags (memory switches)
Defining a Downloaded Bit Image (logo)
Printing a Downloaded Bit Image
Starting/ending macro definitions
Enabling/Disabling inverse printing (white on black)
Read the Real Time Clock
Selecting printing position of HRI Code
Setting the left margin
Printing 2-D barcodes
27
1 DATECS DPP-450
89
90
91
92
93
94
GS R
GS S
GS T
GS U
GS W
GS X
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
GS Z
GS \
GS ^
GS c
GS f
GS h
GS k
GS p
GS q
GS w
GS x
FS !
FS &
FS FS .
FS C
FS S
FS W
ESC y WAN
User manual
Filling or inverting a rectangle in page mode
Selecting 2-D barcode cell size
Selecting the print direction in page mode
Selecting standard mode
Setting the print area width
Drawing a rectangular box with selected thickness in page
mode
Printing the non blank page area only in page mode
Specifying the relative vertical position in page mode
Executing macro
Setting the Real Time Clock
Setting the font of HRI characters of the barcode
Setting the height of the barcode
Printing a barcode
Settings for 2D barcode PDF417
Selecting the height of the module of 2D barcode PDF417
Selecting the horizontal size (Scale factor) of the barcode
Direct text print in page mode
Specifying printing mode of two-byte text data
Selecting two-byte text mode (JIS or GB2312)
Selecting/Canceling underline mode for two-byte text mode
Canceling two-byte text mode
Selecting Shift-JIS mode (Japanese version only)
Specifying character spacing for two-byte text mode
Selecting double size characters for two-byte text mode
WAN
5.11 Connecting Device
The DPP-450 is designed to use different methods of communications. Care
must be taken to ensure that the DPP-450 USB/RS 232 connector and PDA &
Smartphone connector are not accidentally damaged. The figures below show how to
attach the different device to the DPP-450.
USB ( Cabled ) Version:
Connect the DPP-450 using Mini USB cable is shown in the figure below.
USB/RS 232
connector
28
1 DATECS DPP-450
User manual
Bluetooth version:
The DPP-450 Bluetooth version uses Bluetooth® wireless technology to connect to
Bluetooth enable devices.
iOS devices:
Connect to LineaTAB.
Start – LibraryDemo on iPad. Connect LineaTab to iPad(Figure 4). After this press
settings button.
Turn on DPP-450 Bluetooth printer. From setting menu press Discover printers, and
wait to find printers. When is found press on selected printer and wait connect.
ECS/POS Ready
BTH
On DPP-450 LCD screen is show message “BTH”, when is connected.
Press on LineaTAB “Print “ button:
29
1 DATECS DPP-450
User manual
On “Print” menu can printing via Bluetooth connection:
Print Self-test
Demo fonts
Demo barcodes
Demo graphics
To terminate the BT connection, press settings menu and name of printer. When is
close connection the “tick” will disappearing.
5.12 Mount Strap
Strap
30
1 DATECS DPP-450
User manual
31

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 31
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : ecba67ff-14bf-11e4-0000-54fa4f0f87c0
Producer                        : Nitro PDF PrimoPDF
Modify Date                     : 2014:07:23 15:25:46-03:00
Create Date                     : 2014:07:23 15:25:46-03:00
Creator Tool                    : PrimoPDF http://www.primopdf.com
Document ID                     : ecba67ff-14bf-11e4-0000-54fa4f0f87c0
Format                          : application/pdf
Title                           : Microsoft Word - DPP-450_UM-EN_Datecs.doc.doc
Creator                         : nuncho
Author                          : nuncho

EXIF Metadata provided by EXIF.tools