DATECS DATECSBTIOS Bluetooth Module User Manual DPP 250 UM EN Datecs
DATECS LTD. Bluetooth Module DPP 250 UM EN Datecs
DATECS >
Contents
- 1. User manual 1 of 2
- 2. User manual 2 of 2
User manual 1 of 2
User Manual ESC/POS PRINTER DPP-250 1 DATECS DPP-250 User manual THE INFORMATION IN THIS DOCUMENT CANNOT BE REPRODUCED IN ANY MECHANICAL, ELECTRICAL OR ELECTRONIC WAY AND UNDER ANY CIRCUMSTANCES WITHOUT THE WRITTEN CONSENT FROM DATECS LTD. VERSION: April 2013 1 DATECS DPP-250 User manual Legal Notice “Made for iPod,” “Made for iPhone,” and Made for iPad” mean that an electronic accesory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible fort he operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accesory with iPod, iPhone, or iPad may affect wireless performance. Compatability Made for iPhone 5 iPhone 5S iPhone 5C iPhone 4S iPhone 4 th iPod touch (5 generation) th iPod touch (4 generation) rd iPod touch (3 generation) iPad (4th generation) iPad mini iPad (3rd generation) iPad 2 iPad, iPhone, iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Lightning is a trademark of Apple Inc. 1 DATECS DPP-250 User manual This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. CAUTION: Use shielded cables to connect this device to computers. Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. 1 DATECS DPP-250 User manual CONTENTS Legal Notice............................................................................................................................................. 3 Compatability........................................................................................................................................... 3 1. Technical specification ........................................................................................................................ 6 2. Box Contents ....................................................................................................................................... 8 3. Compatible Devices............................................................................................................................. 8 4. Getting Started .................................................................................................................................... 9 5. About Your DPP-250 ......................................................................................................................... 10 5.1 DPP-250 right view 1.................................................................................................................. 10 5.2 DPP-250 right view 2.................................................................................................................. 10 6. Charging the DPP-250 ...................................................................................................................... 10 6.1 DPP-250 Charging ..................................................................................................................... 11 6.1 DPP-250 Full Charge ................................................................................................................. 11 7. Status & Operating Modes ................................................................................................................ 11 8. Loading Paper ................................................................................................................................... 12 9. Diagnostic Information....................................................................................................................... 13 10. DIP Switch Settings ......................................................................................................................... 15 10.1 DIP SWITCH SETTINGS: ........................................................................................................ 15 10.2 Dip switch Location .................................................................................................................. 15 10.3 Memory Switch Settings........................................................................................................... 16 10.4 Setting Memory Switch............................................................................................................. 16 10.5 Memory Switch Details............................................................................................................. 17 11. Pairing Info Details .......................................................................................................................... 18 11. Communications Configuration ....................................................................................................... 18 12. Connecting Device .......................................................................................................................... 19 12.1 Serial / USB ( Cabled ) Version:............................................................................................... 20 12.2 BLUETOOTH® Version: .......................................................................................................... 20 12.3 BLUETOOTH® Version with iOS Bluetooth............................................................................. 20 13. Bluetooth® Setup ............................................................................................................................ 21 14. Loading Drivers ............................................................................................................................... 23 15. Magnetic Card Reader (MS Version only)....................................................................................... 25 16. Smart Card Reader (SC Version only) ............................................................................................ 25 17. Replacing Battery ............................................................................................................................ 26 18. Developing Solutions....................................................................................................................... 27 19. Troubleshooting............................................................................................................................... 28 20. List of commands for ESC/POS mode ............................................................................................ 29 1 DATECS DPP-250 User manual 1. Technical specification Printing Method Direct line thermal Print Width 48mm, 384 dots/line Dot Density 8 x 8 dots/mm (203 dpi x 203 dpi) Print Speed 60mm/sec max Fonts Resident Fonts: Font А: 12 х 24 dots (32 characters/line) Font B: 9 х 16 dots (42 characters/line) Graphic Logo 1x Black & White, Size: 384 x 248 dots Barcode Types 1D: EAN 13, EAN 8, UPC A, UPC E, Code 39, Code 93, Code 128, Codabar, 2 of 5 interleaved, 2D: PDF417, QR code Paper spec: • Width: 58mm • Paper roll: φ45mm or less • Thickness: 60-65µm Paper Loading Easy paper loading Paper Feed System Step Connectivity • RS-232C – max 115200bps • Mini USB 2.0 (device) • BT 2.0 Class 2 (option) - SPP - Serial Port Profile • BT 3.0 Class 2 (option) - SPP - Serial Port Profile - iAP - iPod Accessory Protocol LED Indication • Paper end or paper out • Cover open • Low battery • Print head overheating Audio Indications Electro-magnetic buzzer Buttons • Power button • Feed button Loadable Fonts: Font C: 12 х 24 dots (32 characters/line) Font D: 9 х 16 dots (42 characters/line) Font E: 24 х 24 dots (16 characters/line) Japanese vers. only (option) Font F: 24 х 24 dots (16 characters/line) Chinese vers. only (option) • Battery charging • Bluetooth connection • Reading Magnetic card 1 DATECS DPP-250 User manual Buffer Size up to 128 kB Periphery • Magnetic Stripe Reader - 3-track bi-directional reading - Compliant with ISO 7810, 7811 and 7813 • Smart Card Reader - Compliant with ISO7816 Emulation • ESC/POS Power Supply AC Adapter • Input: AC 100-240V~, 50/60Hz, 0.3A • Output: DC 9V, 1A Battery Rechargeable Li-Ion battery 7.4V / 1150mAh Battery charge time - 2 hours Battery capacity per charge ~ 20 000 lines Reliability • Thermal head: 50 000 000 pulses or 50km • Chip card: 500 000 cycles • Magnetic card:1 000 000 swipes Weight, kg 0.295 (w/o paper, include battery) 0.350 (with paper, include battery) Dimensions,(WxDxH) mm 86 x 113 x 57 (with magnetic stripe reader) Environmental • Operating: +0°C to +40°C / 30 to 85% RH • Storage: -20°C to +60°C / 0 to 90% RH Drop Test Height: 1.2m 3 times on each of the 6 faces 3 times on each of the 4 edges OS compatibility iOS, Android OS, BlackBerry OS, Windows OS, Win CE, Windows Mobile, Windows Phone Accessories Metal belt clip Table 1 1 DATECS DPP-250 User manual 2. Box Contents Your DPP-250 comes with the following items listed below: Item Part Number Descriptions 1. DPP-250xx DPP-250 Thermal Printer 2. AC charger 3. 1 Roll of thermal paper 4. User's manual, CD with Datecs Software 5. RS-232 interface cable Image Table 2 Software (Drivers & SDK): Because of the continually evolving Driver & SDK to support new mobile devices, Drivers & SDK are distributed online and is available for download at our website indicated below. For details on using the DPP-250 Drivers & SDK, please refer to the SDK’s documentation. For the latest DPP-250 SDK’s, visit our developer web site at: http://www.datecs.bg 3. Compatible Devices The DPP-250 (Serial & USB) / DPP-250 (Bluetooth®) portable thermal printer is designed specifically for use with most PDA & Smartphone devices. The DPP-250 can be used in a variety of applications where Printing/Card Reading is required. 1 DATECS DPP-250 User manual User Notes: Compatibility depends on the type of communication method “Serial / USB / Bluetooth®” your PDA or Smartphone supports and the availability of DPP-250 driver for your device. Determine the method of communications your device supports. Next determine if your device is supported by the DPP-250 Drivers & SDKs. Because of the continually evolving Driver & SDK to support new mobile devices, visit our developer web site at: http://www.datecs.bg 4. Getting Started The DPP-250 allows you to printer information from your PDA & Smartphone. Before using the DPP-250 thermal printer the battery should be properly charged. The following Quick Start guide will help to get your DPP-250 ready for use. Quick Start: Steps What to do Charge the DPP250 Rechargeable battery pack as recommended in this manual Load DPP-250 print media (Thermal Paper) Setup Pairing Bluetooth Install DPP-250 Software Purpose Where to find more The Lithium Ion battery pack should be fully charged before use Charging Battery, Page 8 to ensure long battery life. DPP-250 requires Thermal paper for printing. Loading Paper, Page 9 Setup Bluetooth® pairing to allow DPP-250 to communicate with Bluetooth® Setup, Page 19 Bluetooth® Printing software is not provided by Datecs. Please contact your To print information from DPP-250 reseller for your device, software needs to recommendations on be installed onto your device. Third-Party solutions. Developers should refer to the section in this manual on “Developing Solutions”. Table 3 1 DATECS DPP-250 User manual 5. About Your DPP-250 5.1 DPP-250 right view 1 Figure 1 5.2 DPP-250 right view 2 Figure 2 6. Charging the DPP-250 The DPP-250 uses a Lithium Ion rechargeable battery pack. Before first use, the DPP-250 battery pack should be charged for at least 12 hours. To prevent electrical damage to the pack, please use approved AC Charger only. 10 DPP-250 and/or battery 1 DATECS DPP-250 User manual 6.1 DPP-250 Charging Figure 3 6.1 DPP-250 Full Charge Figure 4 7. Status & Operating Modes The DPP-250 uses LEDs to indicate various conditions of operation. This may be charging, active or online, battery low conditions. The following explains these conditions and LED indication. LED Function 1. It lights in green – the printer power is on. 2. It lights in red – end of the paper or paper out. After the loading a new paper roll, LED turns green. ERR 3. It flashes green/red – the printer thermal head is overheating. The printer stops printing. When the printer head temperature returns to normal the ERR LED lights green and the printer continues to print. 4. It flashes green – low battery. 5. When switching ON the printer, while the LF button is pressed, red and green lights are rotated after every beep (up to the fifth). BATT 6. While long pressing the ON/OFF button it flashes green/red after a beep. After releasing the ON/OFF button it lights green. 1. When the adapter is switched ON only one of the BATT LED diodes is lighting green, depending on the battery status (from left to right - low battery to fully charged battery). For details see Section "Charging the Battery". 11 1 DATECS DPP-250 User manual 2. When the adapter is switched ON the BATT LED diodes are lighting as shown on the illustration in Section "Charging the Battery", up to full battery charging. BT 3. When reading a Magnetic Card, the BATT LED are lighting simultaneously in both directions – from the middle outwards to the left and right. 1. It lights blue when PAIRING. Table 4 8. Loading Paper The DPP-250 uses a drop-and-load design making paper loading easy and trouble free. To load paper, simply lift up the paper cover latch and drop in the new roll as shown in the steps below. 1. Slide the paper cover latch to unlock the paper cover as shown in the figure on the right. 2. Lift the paper cover latch to open the paper cover as shown in the figure on the left. 3. Drop in the new roll of thermal media as shown in the figure on the right. Be sure to pull at lease 12 mm or more of media above the top of the printer before closing. 4. Close the paper cover until it snaps lock. 5. Slide paper cover latch to lock the cover in place. 12 1 DATECS DPP-250 User manual 9. Diagnostic Information The DPP-250’s LF switch/button is used for entering various printer modes. These modes can be used to assist developers in debugging problems related to programming and communication. The following explain how to access the various operating modes. Step #1: Make sure the printer is OFF (On-line LED is OFF) before performing step #2. Step #2: Press and hold the line feed button (LF). While pressing the (LF) button, press the (POWER) button momentarily and release when one of the conditions below: LF Button Operation Modes Holding LF button while power on for ~ 0.5 sec and releasing it SHORT SELF TEST print. after 1-beep. Holding LF button while power on Hex DUMP mode. All for ~ 2.5 sec and releasing it after input data are printed as 2-beep. hexadecimal. Holding LF button while power on LONG SELF TEST print. for ~ 4.5 sec and releasing it after 3-beep. Holding LF button while power on for more than 8.5 sec and releasing it after the 5-beep (long 4-tone) beep. Program mode – loading the printer firmware. Holding ON button while power on for ~ 4 sec and releasing it after 1beep. Holding ON button while power on for ~ 6 sec. Temporary forcing 9600 bps serial speed. Hardware Setup Mode. Table 5 Note: Care must be taken when entering operating modes to prevent the clearing of factory preset configuration information. Self-test The DPP-250 has a built-in test pattern that shows the printer’s current configuration as well as the various resident printer fonts. The self-test can also be used as a troubleshooting tool to determine printing problems or battery level. The steps below show how the self-test is printed activated. 13 1 DATECS DPP-250 User manual • Resident font sizes • Characters per line • Text formatting • Resident character set • Resident barcode symbols • Printer’s Configuration 14 1 DATECS DPP-250 User manual 10. DIP Switch Settings The DPP-250 is designed to use different methods of communications. Care must be taken to ensure that the DIP Switches are not changed from its default factory configuration unless required. 10.1 DIP SWITCH SETTINGS: The printer has two absolutely different operation modes. They are determined by the state of switch Sw2: •Continuous Paper mode •Black Mark mode These two modes detect paper present conditions differently. The black mark searching mode is designed for proper alignment of the starting print position on indexed media with printed information. Switch SW1 SW2 SW3 SW4 OFF Enable BT Continuous Paper mode None Normal operation mode ON Disable BT Black Mark mode Xon/Xoff protocol Protocol mode Table 6 10.2 Dip switch Location # 1 - Remove battery cover # 2 - Remove battery Figure 9 15 1 DATECS DPP-250 User manual Figure 10 10.3 Memory Switch Settings The DPP-250 uses nonvolatile memory for storing some of the printer default configuration. The following table shows the available options. Memory Switch Options Memory Switch 1000000010 (see command reference GS command) BAUD RATE 115200 bps POWER OFF TIME 10 minutes PRINT DENSITY 100% CHARACTER TABLE WESTERN (1252) Table 7 10.4 Setting Memory Switch MEMORY SWITCH SETTINGS: Step #1: Make sure the printer is OFF (ERR LED is OFF) before performing step #2. Step #2: Press and hold the power (LF) button. The ERR LED flashes red / green every second. Step #3: Release the (ON) button in about 6 sec. and wait for the printer to print out the current memory settings. Follow the printer instructions to make the necessary changes. 16 1 DATECS DPP-250 User manual The pressing LF (YES) – confirms changes. The pressing ON/OFF (No) – cancels changes. Note: Care must be taken when changing factory preset configuration information. 10.5 Memory Switch Details •SW1: Enable/Disable buzzer. 17 1 DATECS DPP-250 User manual •SW2: Disable CR / CR is executed as LF •SW3: Enable/Disable LF •SW4: LF immediately after CR/ Disable LF immediately after CR •SW5: Font A (12x24)/ Font B (9x16) •SW6-7: Reserved for future features. •SW8: Prevents others from discovering printer when set to ENABLE. Must be set after pairing is completed. •SW9: Disable/Enable USB. Allow the use of USB port for communications. •SW10: (OFF) set USB as the host mode. Host/Device 11. Pairing Info Details BAUD RATE: AUTO OFF TIME: PRINT DENSITY: CHARACTER TABLE: PAIRING INFO: Default is 115200 Default is 5 minutes Default is 100% Default is WESTERN (1252) Default is (SAVE=No) Notes: When saving pairing information, the printer remembers Bluetooth information of the last device connected (paired) to the printer. Saving pairing info prevents the printer from asking for passkey upon initialization. The process for using this option is described below. "To speed this programming process, you may bypass the memory switch settings by indicating "NO" via pressing of thebutton when the printer prints "CHANGE MEMORY SWITCHES" as shown on page 17. This will advance you to the next level of setting where pairing can be found". 1. Following instruction on page-13, change the Pairing Info option to [Save = Yes]. 2. Turn the printer on and pair the printer to your Bluetooth device. 3. The printer will now remember the pairing information and not prompt user for a passkey on every printer initialization. Clearing Pairing Info: 1. Following instruction on page-13, change the Pairing Info option to [Save = No]. 2. Turn on the printer and pair the new Bluetooth device to the printer. 3. The printer will prompt user for a passkey on every printer initialization. 11. Communications Configuration 18 1 DATECS DPP-250 The following default communication methods. User manual configurations are used for the different • Communication with PDA device • Via Bluetooth/ USB/ Serial: Memory Switch Options Memory Switch ( 1 thru 10 ) *******010 Physical Switch Options DIP Switch (1, 2, 3 ,4) *, OFF, OFF, ON Table 8 • Communication with PC (using windows printer driver) • Via Bluetooth/ USB/ Serial: Memory Switch Options Memory Switch ( 1 thru 10 ) *******011 Physical Switch Options DIP Switch (1, 2, 3 ,4) *, OFF, OFF, OFF Table 9 • Service mode (changing printer settings, loading firmware) communication with PC • Via Serial Memory Switch Options Memory Switch ( 1 thru 10 ) *******011 Physical Switch Options DIP Switch (1, 2, 3 ,4) *, OFF, *, ON Table 10 * - depending on user requirements can be 1 or 0 Notes: When not using Driver/SDK developer tools, set DIP Switch 4 to OFF. 12. Connecting Device The DPP-250 is designed to use different methods of communications. Care must be taken to ensure that the DPP-250 USB or Serial connector and PDA & Smartphone connector are not accidentally damaged. The figures below show how to attach the different device to the DPP-250. 19 1 DATECS DPP-250 User manual 12.1 Serial / USB ( Cabled ) Version: • Connect the DPP-250 using Mini USB or Serial cable is shown in the figure below. Figure 11 12.2 BLUETOOTH® Version: The DPP-250 Bluetooth® version uses Bluetooth® wireless technology to connect to Bluetooth® enable devices. See page 19 for details on Bluetooth® setup. Figure 12 12.3 BLUETOOTH® Version with iOS Bluetooth The DPP-250 Bluetooth® version uses Bluetooth® wireless technology to connect to iOS devices with Bluetooth®. iPod iPod iPad iPad 4, iPhone 4, iPhone 4S 5, iPhone 5, iPhone 5S versions mini 20 1 DATECS DPP-250 User manual More information on page 20. Figure 13 13. Bluetooth® Setup Adding New Bluetooth® Device to PDA or Smartphones The following is a brief explanation on how to [Pair] your Bluetooth® DPP-250 to PDA, Smartphones and iOS device. BlackBerry Devices: Add Device or Pairing Bluetooth® peripherals to BlackBerry devices require the use of the device Bluetooth® manager. Image on the right shows a typical Blackberry Bluetooth® manager. When adding / pairing the DPP-250, use the [0000] pairing key when prompted. Windows Mobile Devices: Creating a New Partnership or Pairing Bluetooth® peripherals to your Windows Mobile devices require the use of the device Bluetooth® manager. Image on the right shows a typical Windows Mobile Bluetooth® manager. When adding/pairing the DPP-250, use the [0000] pairing key when prompted. Palm Devices: Add Device or Pairing Bluetooth® 21 1 DATECS DPP-250 User manual peripherals to your Palm devices require the use of the device Bluetooth® manager. Image on the right shows a typical Palm Bluetooth® manager. When adding/pairing the DPP-250, use the [0000] pairing key when prompted. iOS Devices: Enable Bluetooth on iOS device. Select Bluetooth device, after this Pair to DPP-250. When is connected DPP-250 to iOS device, blue LED on DPP-250 will start blinking. Start app “Library Demo” and select “Print”. 22 1 DATECS DPP-250 User manual You can select “Print self test” to test Bluetooth connection. Android devices: Enable Bluetooth and press search device. On the list with available device will show “DDP-250”, pair device. Default PIN is “0000”. When is paired open application “Printer Sample”. Select a device to connect “DPP-250”. For test Bluetooth connection press “Print self test”. 14. Loading Drivers Loading DPP-250 drivers on your PDA or Smartphone. 23 1 DATECS DPP-250 User manual BlackBerry Devices: Blackberry Desktop Manager shown in the figure on the right is used to load third party software on to your device. Please review your device’s documentation on how to use the Application Loader Option to load software on to your device. Windows Mobile Devices: Active Sync shown in the figure on the right is used to install third party applications on to your mobile device. Please review your device’s documentation on how to use the Active Sync Manager to load new software on to your device. In most cases you only need to run the DPP-250 installer to start the installation. Palm Devices: Palm Install Manager Application shown in the figure on the right is used to install third party applications on to your device. Please review your device’s documentation on how to use the Palm Install Manager Application to load new software on to your device. In most cases you only need to drag & drop DPP-250 PRC files in installer and click Add. 24 1 DATECS DPP-250 User manual 15. Magnetic Card Reader (MS Version only) The DPP-250 has a built-in magnetic card reader. The card reader incorporates a (3)-track magnetic read head requiring a single swipe to read field data from all three tracks. The reader’s magnetic head faces towards the front of the printer. When placing the card into the reader, the magnetic strip must be facing as show in the figure above. Keep the bottom edge of the card flat on the inner base of the reader to ensure that the magnetic strip passes over the read head evenly. When swiping the card through the reader, use an even consistent motion from start to finish. The speed of swiping can vary however the speed must be consistent from start to finish of the swipe in order to accurately read card data. User Notes: To use the magnetic card reader feature, special software must be used to read and process the card information. If you do not have card reading software, please consult your reseller to find out if this software is available or contact DATECS for recommendations on compatible third party software solutions. 16. Smart Card Reader (SC Version only) The DPP-250 has a built-in smart card reader (optional). The smart card reader is designed to read information stored embedded on smart chips and process the information using device side software. 25 1 DATECS DPP-250 User manual When placing the card into the reader, the smart chip must be facing to the front of the printer as show in the figure above. Insert the card in to the reader until the card stops. User Notes: To use the smart card reader feature, special software must be used to read and process the smart chip information. Please consult your reseller if this software is available or contact DATECS for recommendations on compatible third party software solutions. 17. Replacing Battery To replace the battery in the DPP-250 thermal printer follow the steps below. Steps: 1. Turn over the DPP-250 and place on a flat surface. Rotate the (2) locking levers as shown in the figure on the right. 2. Lift the battery cover as showed in the figure on the right. 26 1 DATECS DPP-250 User manual 3. Lift the battery as shown in the figure on the right. 4. Detach the battery connector as shown in the figure on the right. Reverse Steps 1-4 to install the new battery pack. 18. Developing Solutions Integrating the DPP-250 into your mobile solution requires the use of the DPP-250 PDA & Smartphone SDK. The SDK incorporates API specific to developing printing applications and using the integrated Magnetic Card Reader / Smart Card Reader capability of the DPP-250. The table below shows the SDKs currently available for PDA & Smartphone devices. OS Android BlackBerry iOS Palm One Windows Mobile Language Java Java Objective-C C ++ Basic Basic VB.Net C ++ C Sharp SDK-IDE Eclipse RIM BlackBerry Java JDE 4.1 and higher Xcode (Objective-C) Code Warrior Satellite Forms NS Basic Microsoft Visual Studio 2005 (.Net) Microsoft Visual Studio 2005 (.Net) Microsoft Visual Studio 2005 (.Net) For details on using the DPP-250 SDK, please refer to the SDK’s documentation. For the latest DPP-250 SDK’s, visit our developer web site at: http://www.datecs.bg 27 1 DATECS DPP-250 User manual 19. Troubleshooting If you’re having problems capturing signatures refer table below for possible causes. Item Problem Paper feeds after issuing a print job but no printed text visible on paper. On-line LED blinks RED continuously. Text and/or graphics are printed very light. Strange characters are printed when printing. Printer stops responding to print and paper feed commands. Printing is light or missing only on half of the print width. to the Possible Cause Thermal media is specially coated on outside of roll. Remove paper roll and reload properly. See section “Loading Paper” for details on loading paper. Paper cover not installed properly. See Section “Loading Paper” for details on replacing paper cover. Battery voltage low. Printer out of paper or Paper not properly loaded. See section “Loading Paper” for details on loading paper. Battery voltage low. See section on charging battery pack. Thermal media not imaging correctly. Verifythat you are using the recommended thermal media. Battery voltage low. See section on charging battery pack. Remove battery for 5 seconds and reconnect battery. Paper cover not properly installed. See section on loading paper. Mechanism jarred loose. Contact technical support. 28 1 DATECS DPP-250 User manual 20. List of commands for ESC/POS mode № Command BEL HT LF FF CR 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 DC2 = DC3 ( DC3 + DC3 DC3 A DC3 B DC3 C DC3 D DC3 F DC3 L DC3 M DC3 P DC3 p DC3 v CAN ESC FF ESC RS ESC SP ESC # ESC $ 26 ESC % 27 28 29 30 31 32 33 34 35 36 37 38 39 40 ESC & ESC ! ESC * ESC + ESC ESC . ESC 2 ESC 3 ESC < ESC = ESC > ESC ? ESC @ ESC CAL Description Sounds the buzzer Horizontal Tab command Printing а line and Paper Feeding command Printing and paper feeding to the black mark position The operation of the command depends on the state of the configuration flags 2, 3 and 4 Image LSB/MSB select DC3 (Ruled line) commands sequence start Sets the ruled line ON Sets the ruled line off Selects ruled line A Selects ruled line B Clears selected ruled line buffer Sets a single dot in selected ruled line buffer Ruled line pattern set Ruled line set Selects ruled line combine mode Ruled line 1 dot line print Ruled line n dots line print Ruled line image write Canceling print data in page mode Printing data in page mode Sounds the buzzer Setting character spacing Setting EURO symbol position Specifying the absolute horizontal position of printing Selecting/Canceling the printing of downloaded user character set Selecting user character set Specifying printing mode of text data Printing graphical data Switch’s OFF the printer Selecting/Canceling underlining Printing self test/diagnostic information Specifying 1/6-inch line feed rate Specifying line feed rate n/203 inches Changes print direction to opposite Data input control Selecting print direction Reading magnetic stripe card Initializing the printer Black mark mode sensor calibration 29 1 DATECS DPP-250 41 42 43 44 45 46 47 48 49 50 51 52 ESC D ESC E ESC F ESC G ESC I ESC J ESC L ESC N ESC R ESC S ESC T ESC U 53 ESC V 54 55 56 57 58 59 60 61 ESC W ESC X ESC Y ESC Z ESC \ ESC ] ESC ^ ESC _ 62 ESC ` 63 64 65 66 67 68 ESC a ESC b ESC c5 ESC d ESC i ESC o 69 ESC pair= 70 71 72 73 74 ESC pwd= ESC r ESC s ESC u ESC v 75 ESC x 76 ESC y 77 ESC { 78 GS FF 79 GS $ 80 GS ) User manual Setting horizontal tab position Specifying/Canceling highlighting Filling or inverting the page area in page mode Specifying/Canceling highlighting Specifying/Canceling Italic print Printing and Paper feed n/203 inches Selecting page mode Reading programmed serial number Selecting country Specifying speed (bps) of the serial port Printing short self test Selecting/Canceling underlined printing Selecting/Canceling printing 90°- right turned characters Defining the print area in page mode Specifying max printing speed Selecting intensity level Returning diagnostic information Specifying relative horizontal position Loading the default settings stored in Flash memory Saving current settings in Flash memory Loading factory settings Reading the Battery Voltage and Thermal head temperature Aligning the characters Increasing text line height Enabling/Disabling the functioning of the button LF Printing and feeding paper by n- lines Feeding paper backwards Temporarily feeding paper forward Enabling/Disabling PAIRING info saving in Bluetooth mode Programming a new Bluetooth password (PIN) Full command for sounding buzzer Reading printer settings Selecting code table Transmitting the printer status Setting the time interval for automatically switching Off the printer Setting USB response strings Enabling/Canceling printing of 180° turned characters Printing in page mode and returning to standard mode Specifying the absolute vertical position in page mode Setting printer flags (memory switches) 30 1 DATECS DPP-250 81 82 83 84 85 86 87 88 89 90 91 92 93 GS * GS / GS : GS B GS C GS H GS L GS Q GS R GS S GS T GS U GS W 94 GS X 95 96 97 98 99 100 101 102 GS Z GS \ GS ^ GS c GS f GS h GS k GS p 103 GS q 104 GS w 105 GS x User manual Defining a Downloaded Bit Image (logo) Printing a Downloaded Bit Image Starting/ending macro definitions Enabling/Disabling inverse printing (white on black) Read the Real Time Clock Selecting printing position of HRI Code Setting the left margin Printing 2-D barcodes Filling or inverting a rectangle in page mode Selecting 2-D barcode cell size Selecting the print direction in page mode Selecting standard mode Setting the print area width Drawing a rectangular box with selected thickness in page mode Printing the non blank page area only in page mode Specifying the relative vertical position in page mode Executing macro Setting the Real Time Clock Setting the font of HRI characters of the barcode Setting the height of the barcode Printing a barcode Settings for 2D barcode PDF417 Selecting the height of the module of 2D barcode PDF417 Selecting the horizontal size (Scale factor) of the barcode Direct text print in page mode Asian Languages Support 106 107 FS ! FS & 108 FS - 109 110 111 FS . FS C FS S 112 FS W Specifying printing mode of two-byte text data Selecting two-byte text mode (JIS or GB2312) Selecting/Canceling underline mode for two-byte text mode Canceling two-byte text mode Selecting Shift-JIS mode (Japanese version only) Specifying character spacing for two-byte text mode Selecting double size characters for two-byte text mode 31
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 31 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : 76af0441-14b1-11e4-0000-7ee59c7a77a7 Producer : Nitro PDF PrimoPDF Modify Date : 2014:07:23 13:41:58-03:00 Create Date : 2014:07:23 13:41:58-03:00 Creator Tool : PrimoPDF http://www.primopdf.com Document ID : 76af0441-14b1-11e4-0000-7ee59c7a77a7 Format : application/pdf Title : Microsoft Word - DPP-250_UM-EN_Datecs.doc Creator : nuncho Author : nunchoEXIF Metadata provided by EXIF.tools