DLP Design UHF1B RFID Transmitter User Manual DLP RFID UHF1B Datasheet v34b

DLP Design, Inc. RFID Transmitter DLP RFID UHF1B Datasheet v34b

user manual

Download: DLP Design UHF1B RFID Transmitter User Manual DLP RFID UHF1B Datasheet v34b
Mirror Download [FCC.gov]DLP Design UHF1B RFID Transmitter User Manual DLP RFID UHF1B Datasheet v34b
Document ID1165130
Application IDpG8SZV9gjm+OSmjWaKE7hw==
Document Descriptionuser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize8.85kB (110638 bits)
Date Submitted2009-09-05 00:00:00
Date Available2009-09-05 00:00:00
Creation Date2009-09-01 14:15:10
Producing SoftwareAcrobat Distiller 8.1.0 (Windows)
Document Lastmod2009-09-03 16:51:39
Document TitleMicrosoft Word - DLP-RFID-UHF1B Datasheet-v34b.doc
Document CreatorPScript5.dll Version 5.2.2
Document Author: Don

DLP-RFIDU H F 1B
LEAD FREE
CLASS 1/GEN 2 RFID READER-WRITER
**PRELIMINARY DOCUMENT-SUBJECT TO CHANGE**
FEATURES:
• ISO 18000, EPC Class 1–Gen 2 Compatible
• Read UID of Up to 15 Tags Simultaneously
• 18dBm Output Power
• UHF Reader/Writer
• Reverse Polarity SMA Antenna Connector
• FCC/IC/CE Modular Approval Pending
• Permanent, Unique Serial Number Accessible via USB
• Integrated Pass/Fail Beeper
• USB Port Powered from the Host PC (USB 1.1/2.0 Compatible)
• USB Drivers Provided for Windows Vista, XP, XPx64, Server2003, 2000
• Software Development Library Support for Visual
C++/Visual Basic
APPLICATION AREAS:
•
•
•
•
•
•
•
Real-Time Security
Personal Identification
Pharmaceutical Tracking
Inventory/Asset Management & Tracking
Library/Book Management & Tracking
Baggage Tagging
Sports Event Timing
Rev 1.1 (April 2009)
© DLP Design, Inc.
1.0 INTRODUCTION
Note: The retail boxed version of this product includes the DLP-RFID-UHF1B reader, a
retractable USB cable, a small loop antenna, 3-foot coax and two UHF RFID tags.
The DLP-RFID-UHF1B is a low-cost, USB-powered module for reading from and writing to ISO
18000-6a, -6b and -6c intelligent RFID transponder tags. It has the ability to both read and write
data in addition to reading the unique identifier (UID). All of the DLP-RFID-UHF1B’s electronics
reside within the compact unit, and all operational power is taken from the host PC via the USB
interface.
2.0 RFID BASICS
RFID stands for Radio Frequency IDentification. It is an electronic technology whereby digital
data encoded in an RFID tag (or transponder) is retrieved utilizing a reader. In contrast to bar
code technology, RFID systems do not require line-of-sight access to the tag in order to retrieve
the tag’s data, and they are well suited to harsh environments.
An RFID tag consists of an integrated circuit attached to an antenna. In the case of the tags
used with the DLP-RFID-UHF1B, the antenna is in the form of conductive ink “printed” onto a
material that allows for connection to the integrated circuit. This type of passive (battery-free)
tag is commonly referred to as an “inlay”.
The RFID reader (or “interrogator”) is typically a microcontroller-based radio transceiver that
powers the tag with a time-varying electromagnetic radio frequency (RF) field. When the RF
field passes through the tag’s antenna, AC voltage is generated in the antenna and rectified to
supply power to the tag. Once powered, the tag can receive commands from the reader. The
information stored in the tag can then be read by the reader and sent back to the host PC for
processing.
The data in the tag consists of a hard-coded, permanent serial number (or UID) and user
memory that can be written to, read from and locked if desired. Once locked, user data can still
be read but not changed.
Rev 1.1 (April 2009)
© DLP Design, Inc.
3.0 SPECIFICATIONS
Reader Frequency
Output Power
Range
Tags/Protocols Supported
Communications Interface
Operational Power – Active
Operational Power – Idle
Antenna Connector
USB Driver Support
Physical Dimensions – Retail
Operating Temperature
902.6-927.4MHz
18dBm MAX
1-6 inches (Depends upon the type of RFID tag)
ISO18000-6a, 6b and 6C
USB 1.1/2.0 Compatible; Mini-B 5-Pin Connector
320mA
45mA
Reverse Polarity SMA*
Windows Vista, XP, XPx64, Server2003, 2000,
Linux, Mac OSX
Enclosure: .83x2.3x3.25” typ. (21.1x58.4x82.6mm)
0-70°C
*Please see the Antenna Section for important regulatory details.
4.0 PERMANENT READER SERIAL NUMBER
Each DLP-RFID-UHF1B contains a unique, 32-bit, hard-coded serial number that cannot be
altered by any means. The serial number can be read via the USB interface and used to
identify the reader via the host software.
5.0 APPLICATION DEVELOPMENT
A software library is available for free download upon purchase of the DLP-RFID-UHF1B that
demonstrates reading the serial number (UID) from transponder tags, writing to the tags,
accessing the reader’s permanent serial number and controlling the integrated pass/fail beeper.
Additionally, a low-power Mode Enable command is provided to reduce current consumption to
approximately 45mA when communication with a tag is not required.
Rev 1.1 (April 2009)
© DLP Design, Inc.
6.0 REGULATORY AGENCY CONSIDERATIONS
6.1 AGENCY IDENTIFICATION NUMBERS
Compliance with the appropriate regulatory agencies is essential in the deployment of all
transceiver devices. DLP Design will obtain modular approval for this RF product such that an
OEM need only meet a few basic requirements in order to utilize their end product under this
approval. Corresponding agency identification numbers will be listed below:
Part Number
US / FCC
CANADA / IC
DLP-RFIDUHF1B
SX9UHF1B
5675A-UHF1B
6.2 EXTERNAL ANTENNAS
The DLP-RFID-UHF1B will be approved for use with selected external antennas. Connection is
made via reverse-polarity SMA connectors.
A magnetic loop antenna is provided with each DLP-RFID-UHF1B reader purchased from DLP
Design as shown below:
This antenna is well suited for reading the near-field loop incorporated into many Gen-2 tags.
This antenna requires a coax cable with a reverse-polarity SMA connector at one end for
connection to the DLP-RFID-UHF1B reader. A 3-foot coax cable is provided with each DLPRFID-UHF1B reader purchased from DLP Design.
6.3 FCC/IC REQUIREMENTS FOR MODULAR APPROVAL
Any changes or modifications to the DLP-RFID-UHF1B’s printed circuit board or magnetic loop
antenna could void the user’s authority to operate the equipment.
6.4 WARNINGS
Rev 1.1 (April 2009)
© DLP Design, Inc.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesirable operation.
This device is intended for use under the following conditions:
1. The transmitter module may not be co-located with any other transmitter or antenna; and,
2. The module will be approved using the FCC’s “unlicensed modular transmitter approval”
method. Only loop antennas which do not exhibit a directional gain greater than that of the
antenna approved with the device may be used.
As long as these two conditions are met, further transmitter testing will not be required.
However, the OEM integrator is still responsible for testing their end product for any additional
compliance measures necessitated by the installation of this module (i.e. digital device
emissions, PC peripheral requirements, etc.).
Note: In the event that these conditions cannot be met (i.e. co-location with another
transmitter), then the FCC authorization is no longer valid, and the corresponding FCC ID may
not be used on the final product. Under these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and obtaining a
separate FCC authorization.
6.5 OEM PRODUCT LABELING
The final end product must be labeled in a visible area with the following text:
“Contains TX FCC ID: SX9UHF1B”
6.6 RF EXPOSURE
In order to comply with FCC RF exposure requirements, the antenna used for this transmitter
must not be co-located or operating in conjunction with any other antenna or transmitter.
6.7 ADDITIONAL INFORMATION FOR OEM INTEGRATORS
The end user should NOT be provided with any instructions on how to remove or install the
DLP-RFID-UHF1B. This device will be pre-certified to operate with the antenna models listed
below:
•
DLP Design Near-Field Magnetic Loop Antenna
7.0 DISCLAMER
Rev 1.1 (April 2009)
© DLP Design, Inc.
Neither the whole nor any part of the information contained herein nor the product described in
this datasheet may be adapted or reproduced in any material or electronic form without the prior
written consent of the copyright holder.
This product and its documentation are supplied on an as-is basis, and no warranty as to their
suitability for any particular purpose is either made or implied. DLP Design will not accept any
claim for damages whatsoever arising as a result of the use or failure of this product. Your
statutory rights are not affected.
This product or any variant of it is not intended for use in any medical appliance, device or
system in which the failure of the product might reasonably be expected to result in personal
injury.
This document provides preliminary information that may be subject to change without notice.
8.0 CONTACT INFORMATION
DLP Design, Inc.
1605 Roma Lane
Allen, TX 75013
Phone:
Fax:
Email:
Internet:
469-964-8027
415-901-4859
support@dlpdesign.com
http://www.dlpdesign.com
Rev 1.1 (April 2009)
© DLP Design, Inc.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 6
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:9cd854a0-2476-4503-a991-9a2d6f5fc336
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Create Date                     : 2009:09:01 14:15:10-05:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2009:09:03 16:51:39-05:00
Metadata Date                   : 2009:09:03 16:51:39-05:00
Document ID                     : uuid:41ff43bc-ac07-41e5-9a07-b688b0cdca10
Instance ID                     : uuid:ce5d4dd4-de3b-4ec3-b18d-0848215d91ab
Format                          : application/pdf
Title                           : Microsoft Word - DLP-RFID-UHF1B Datasheet-v34b.doc
Creator                         : Don
Author                          : Don
EXIF Metadata provided by EXIF.tools
FCC ID Filing: SX9UHF1B

Navigation menu