Datto OM2PV2 Wireless 802.11b/g/n Mesh Router User Manual OM2P v2 UM for FCC CE IC apply v2

Open Mesh, Inc. Wireless 802.11b/g/n Mesh Router OM2P v2 UM for FCC CE IC apply v2

User Manual_rev.pdf

Download:
Mirror Download [FCC.gov]
Document ID	2199256
Application ID	xtr936IcmoiUrRwtOjg2Fw==
Document Description	User Manual_rev.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	114.19kB (1427350 bits)
Date Submitted	2014-02-24 00:00:00
Date Available	2014-02-24 00:00:00
Creation Date	2014-02-24 15:19:17
Producing Software	GPL Ghostscript 9.0
Document Lastmod	2014-02-24 15:23:12
Document Title	OM2P v2_UM_for FCC & CE & IC apply_v2
Document Creator	PDFCreator Version 1.2.0
Document Author:	aihsu

Long Range
Wireless N
Wireless
802.11b/g/n
Client
Bridge/Access
Mesh
RouterPoint
Model:
OM2P v2
User Manual
Version : 1.0
Table of Contents
CHAPTER 1 PRODUCT OVERVIEW............................................................................................................................. 7
1.1 FEATURE ....................................................................................................................................................................... 7
1.2 BENEFITS....................................................................................................................................................................... 8
1.3 PACKAGE CONTENTS...................................................................................................................................................... 9
1.3 SYSTEM REQUIREMENT .................................................................................................................................................. 9
CHAPTER 2 HARDWARE OVERVIEW ........................................................................................................................10
CHAPTER 3 INSTALLATION .......................................................................................................................................11
CHAPTER 4 CONFIGURING YOUR COMPUTER FOR TCP/IP .................................................................................14
4.1 CONFIGURING MICROSOFT WINDOWS 7 ............................................................................................................................ 15
4.2 CONFIGURING MICROSOFT WINDOWS VISTA....................................................................................................................... 17
4.3 CONFIGURING MICROSOFT WINDOWS XP .......................................................................................................................... 19
4.4 CONFIGURING MICROSOFT WINDOWS 2000 ...................................................................................................................... 20
4.5 CONFIGURING AN APPLE MACINTOSH COMPUTER ................................................................................................................ 22
CHAPTER 5 INTRODUCING THE WEB CONFIGURATOR .....................................................................................................23
5.1 LOGGING IN TO THE WEB CONFIGURATOR ........................................................................................................................... 23
CHAPTER 6 STATUS ....................................................................................................................................................25
6.1 SAVE/LOAD ................................................................................................................................................................. 25
6.2 MAIN ......................................................................................................................................................................... 26
6.3 WIRELESS CLIENT LIST ................................................................................................................................................. 27
6.4 SYSTEM LOG ............................................................................................................................................................... 28
6.5 CONNECTION STATUS .................................................................................................................................................. 29
6.6 DHCP CLIENT TABLE ................................................................................................................................................... 30
CHAPTER 7 SYSTEM....................................................................................................................................................31
7.1 CHANGING OPERATING MODES ................................................................................................................................... 31
CHAPTER 8 WIRELESS CONFIGURATION ................................................................................................................33
8.1 WIRELESS SETTINGS..................................................................................................................................................... 33
8.1.1 Access Point Mode ........................................................................................................................................ 33
8.1.2 Client Bridge Mode ....................................................................................................................................... 37
8.1.3 WDS Bridge Mode......................................................................................................................................... 39
8.1.4 Client Router Mode ....................................................................................................................................... 41
8.2 WIRELESS SECURITY SETTINGS...................................................................................................................................... 43
8.2.1 WEP ................................................................................................................................................................ 43
8.2.2 WPA-PSK ....................................................................................................................................................... 44
8.2.3 WPA2-PSK ..................................................................................................................................................... 45
8.2.4 WPA-PSK Mixed ............................................................................................................................................ 46
8.2.5 WPA................................................................................................................................................................ 47
8.2.6 WPA2 ............................................................................................................................................................. 48
8.2.7 WPA Mixed .................................................................................................................................................... 49
8.4 WIRELESS ADVANCED SETTINGS ................................................................................................................................... 50
8.5 WIRELESS MAC FILTER ................................................................................................................................................ 52
8.6 WDS LINK SETTINGS ................................................................................................................................................... 53
CHAPTER 9 LAN SETUP ..............................................................................................................................................54
9.1 IP SETTINGS ................................................................................................................................................................ 54
9.2 SPANNING TREE SETTINGS ........................................................................................................................................... 55
CHAPTER 10 ROUTER SETTINGS ..............................................................................................................................56
10.1 WAN SETTINGS ........................................................................................................................................................ 56
10.1.1 Static IP ........................................................................................................................................................ 56
10.1.2 DHCP (Dynamic IP) .................................................................................................................................... 58
10.1.3 PPPoE (Point-to-Point Protocol over Ethernet) ........................................................................................ 60
10.1.4 PPTP (Point-to-Point Tunneling Protocol) ................................................................................................ 62
10.2 LAN SETTINGS (ROUTER MODE) ............................................................................................................................... 64
10.3 VPN PASS THROUGH ................................................................................................................................................ 65
10.4 PORT FORWARDING .................................................................................................................................................. 66
10.5 DMZ ....................................................................................................................................................................... 68
CHAPTER 11 MANAGEMENT SETTINGS..................................................................................................................69
11.1 ADMINISTRATION ...................................................................................................................................................... 69
11.2 MANAGEMENT VLAN ............................................................................................................................................... 71
11.3 SNMP SETTINGS ...................................................................................................................................................... 72
11.4 BACKUP/RESTORE SETTINGS ...................................................................................................................................... 73
11.5 FIRMWARE UPGRADE ................................................................................................................................................. 74
11.6 TIME SETTINGS.......................................................................................................................................................... 75
11.7 LOG.......................................................................................................................................................................... 76
11.8 DIAGNOSTICS............................................................................................................................................................ 77
CHAPTER 12 NETWORK CONFIGURATION EXAMPLES.........................................................................................78
12.1 ACCESS POINT .......................................................................................................................................................... 78
12.2 CLIENT BRIDGE MODE ............................................................................................................................................... 79
12.3 WDS BRIDGE MODE ................................................................................................................................................. 80
12.4 CLIENT ROUTER......................................................................................................................................................... 81
CHAPTER 13 BUILDING A WIRELESS NETWORK ...................................................................................................81
13.1 ACCESS POINT MODE................................................................................................................................................ 82
13.2 ACCESS POINT MODE WITH WDS FUNCTION ............................................................................................................. 82
13.3 CLIENT BRIDGE MODE ............................................................................................................................................... 83
13.4 WDS BRIDGE MODE ................................................................................................................................................. 83
13.5 CLIENT ROUTER MODE .............................................................................................................................................. 84
13.6 RADIUS CONNECTIONS ........................................................................................................................................... 84
APPENDIX A – TROUBLESHOOTING .................................................................................................................................85
A.1 PROBLEM SOLVING......................................................................................................................................................... 85
A.2 CONTACTING TECHNICAL SUPPORT .................................................................................................................................... 86
APPENDIX B – SPECIFICATIONS .......................................................................................................................................87
APPENDIX C – GLOSSARY ................................................................................................................................................88
APPENDIX D – FCC INTERFERENCE STATEMENT ...............................................................................................................93
About This Document
Audience
This document is written for networking professionals responsible for installing and managing
the EnGenius ENH Series Outdoor Access Point/Bridge. To use this guide, you should have
knowledge about TCP/IP and IEEE 802.11 standards, and be familiar with the concepts and
terminology associated with wireless local-area networks (WLANs).
This document provides the information you need to install and configure your Access
Point/bridge.
Convention
This publication uses these conventions/symbols to convey instructions and information
and highlight special message.
Caution: This symbol represents the important message on incorrect device
operation that might damage the device
Note: This symbol represents the important message for the settings.
Tip: This symbol represents the alternative choice that can save time or
resources.
Icons used
Figures in this document may use the following generic icons.
EHN device
Internet
Power adapter
WLAN signal
Client computer laptop
Client computer desktop
PoE injector
Chapter 1 Product Overview
Thank you for choosing OM2P V2. The OM2P V2 is a long range, high-performance IEEE 802.11b/g/n network
solution that provides Access Point, Client Bridge, WDS, and Client Router functions in a single device.
In addition to providing the latest wireless technology, the OM2P V2 supports Power over Ethernet and Power by
Adapter capabilities, which allow the device to be installed easily in nearly any indoor or outdoor location. Advanced
features include power level control, narrow bandwidth selection, traffic shaping, and Real-time RSSI indication.
A variety of security features help to protect your data and privacy while you are online. Security features include Wi-Fi
Protected Access (WPA-PSK/WPA2-PSK), 64/128/152-bit WEP Encryption, and IEEE 802.1x with RADIUS.
1.1 Feature
The following list summarizes the key features of the OM2P V2:
High-speed data rates up to 150 Mbps make the OM2P V2 ideally suited for handling heavy data
payloads such as MPEG video streaming
Fully Interoperable with IEEE 802.11b/IEEE 802.11g/IEEE 802.11n-compliant devices
Multi-function capabilities enable users to use different modes in various environments
Point-to-point and point-to-multipoint wireless connectivity enable data transfers between two or more
buildings
Channel bandwidth selection allows the appropriate bandwidth to be used to reach various distances
RSSI indicator makes it easy to select the best signal for Access Point connections
Power-over-Ethernet capabilities allow for flexible installation locations and cost savings
Four SSIDs let clients access different networks through a single Access Point, and assign different policies
and functions for each SSID
WPA2/WPA/ WEP/ IEEE 802.1x support and MAC address filtering ensure secure network connections
PPPoE/PPTP function support make it easy to access the Internet via Internet Service Provider (ISP) service
authentication
SNMP Remote Configuration Management helps administrators remotely configure or manage the Access
Point
QoS (WMM) support enhances performance and user experiences
1.2 Benefits
The OM2P V2 is the ideal product around which you can build your WLAN. The following list
summarizes a few key advantages that WLANs have over wired networks:
Ideal for hard-to-wire environments
There are many scenarios where cables cannot be used to connect networking devices.
Historic and older buildings, open areas, and busy streets, for example, make wired LAN
installations difficult, expensive, or impossible.
Temporary workgroups
WLANs make it easy to provide connectivity to temporary workgroups that will later be
removed. Examples include parks, athletic arenas, exhibition centers, disaster-recovery
shelters, temporary offices, and construction sites.
Ability to access real-time information
With a WLAN, workers who rely on access to real-time information, such as doctors and
nurses, point-of-sale employees, mobile workers, and warehouse personnel, can access
the data they need and increase productivity, without having to look for a place to plug
into the network.
Frequently changed environments
WLANs are well suited for showrooms, meeting rooms, retail stores, and manufacturing
sites where workplaces are rearranged frequently.
Wireless extensions to Ethernet networks
WLANs enable network managers in dynamic environments to minimize overhead caused
by moves, extensions to networks, and other changes.
Wired LAN backup
Network managers can implement WLANs to provide backup for mission-critical
applications running on wired networks.
Mobility within training/educational facilities
Training sites at corporations and students at universities are a few examples where
wireless connectivity can be used to facilitate access to information, information
exchanges, and learning.
1.3 Package Contents
Open the package carefully and make sure it contains all of the items listed below.
- One EnGenius Wireless Access Point / Client Bridge (OM2P V2)
If any item is missing or damaged, contact your place of purchase immediately.
Keep all packing materials in case you need to return the OM2P V2. The OM2P V2 must be returned
with its original packing materials.
Use only the power adapter supplied with your OM2P V2. Using a different power
adapter can damage the OM2P V2.
1.3 System Requirement
To install the OM2P V2, you need an Ethernet cable and a computer equipped with:
- An Ethernet interface
One of the following operating systems: Microsoft Windows XP, Vista, or 7; or Linux
An Internet browser that supports HTTP and JavaScript
Chapter 2 Hardware Overview
The following figures show the key components on the OM2P V2.
2.1 Bottom View
The bottom panel of the OM2P V2 contains two RJ-45 ports, a PoE interface, and a Reset button. A
removable cover covers these components.
The RJ-45 port connects to an Ethernet adapter in a computer you use to configure the OM2P V2.
For more information, see Chapter 4.
The PoE interface allows the OM2P V2 to be powered using the supplied PoE injector.
The Reset button can be used to reboot the OM2P V2 and return the device to its default factory
configuration, erasing any overrides you may have made to the device’s default settings. The
Reset button is recessed to prevent accidental resets. To reboot the OM2P V2, use a flat object
such as a pencil to press the Reset button for approximately 10 seconds and then stop pressing
the Reset button.
2.2 Back Panel
The back panel of the OM2P V2 contains the LED indicators that show the link quality and status of the
OM2P V2.
Chapter 3 Installation
This chapter describes how to install the OM2P V2. It also describes the OM2P V2 LEDs.
Only experienced installation professionals who are familiar with local building and safety
codes and, wherever applicable, are licensed by the appropriate government regulatory authorities
should install the OM2P V2.
3.1 Pre-installation Guidelines
Select the optimal locations for the equipment using the following guidelines:
The OM2P V2 should be mounted on a 1"-4" pole. Its location should enable easy access to the
unit and its connectors for installation and testing.
The higher the placement of the antenna, the better the achievable link quality.
The antenna should be installed to provide a direct, or near line of sight with the Base Station
antenna. The antenna should be aligned to face the general direction of the Base Station.
3.2 Installing the OM2P V2
To install the OM2P V2, use the following procedure to mount the device on a pole and refer to
the figure below.
1. The bottom of the OM2P V2 is a movable cover. Grab the cover and pull it back hard
to remove the cover.
2. Insert a standard Ethernet cable into the RJ-45 port labeled MAIN LAN.
3. Slide the cover back to seal the bottom of the OM2P V2.
4. Remove the power cord and PoE injector from the box and plug the power cord into the
DC port of the PoE injector.
Only use the power adapter supplied with the OM2P V2. Using a different power
adapter might damage the OM2P V2.
5. Plug the other side of the Ethernet cable in step 3 into the PoE port of the PoE injector.
When you finish step 5, the installation will resemble the following picture.
6. Turn over the OM2P V2. Then insert the mast strap through the middle hole of the OM2P
V2.
Use a screwdriver to unlock the pole-mounting ring putting it through the OM2P V2.
7. Mount the EOA200 securely to the pole by locking the strap tightly.
This completes the installation procedure.
3.2 Understanding the OM2P V2 LEDs
The rear of the OM2P V2 has two groups of LEDs. One group, labeled INDICATORS, shows the status
of the device. The second group, LINK QUALITY, shows the strength of the link between the OM2P
V2 and the network. The following table describes the OM2P V2 LEDs.
LED
Color
Mode
Status
Power
Green
OFF= OM2P V2 is not receiving power.
ON= OM2P V2 is receiving power.
LAN
Green
OFF = OM2P V2 is not connected to the network.
ON = OM2P V2 is connected to the network, but not sending
or receiving data.
Blink = OM2P V2 is sending or receiving data.
WLAN
Green
Access Point OFF = OM2P V2 radio is off and the device is not
or Client
sending or receiving data over the wireless LAN.
Bridge Mode ON = OM2P V2 radio is on, and the device is not
sending or receiving data over the wireless LAN.
Blink = OM2P V2 radio is on, and the device is sending
or receiving data over the wireless LAN.
Link Quality
See Status
column
Access Point Shows the strength of the link between the OM2P V2
and the network.
or Client
Bridge Mode G = good quality (green).
Y = medium quality (yellow).
R = poor or no link (red).
Chapter 4 Configuring Your Computer for TCP/l P
To configure the OM2P V2 use a computer that is configured for TCP/IP. This chapter describes how
to configure the TCP/IP settings on a computer that will be used to configure the OM2P V2.
4.1 Configuring Microsoft Windows 7
Use the following procedure to configure a computer running Microsoft Windows 7.
1. In the Start menu search box, type: ncpa.cpl
2. When the Network Connections List appears, right-click the Local Area Connection icon
and click Properties.
3. In the Networking tab, click either Internet Protocol Version 4 (TCP/IPv4) or Internet
Protocol Version 6 (TCP/IPv6), and then click Properties.
4. In the properties dialog box, click Obtain an IP address automatically to configure your
computer for DHCP.
5. Click the OK button to save your changes and close the dialog box.
6. Click the OK button again to save your changes.
4.2 Configuring Microsoft Windows Vista
Use the following procedure to configure a computer running Microsoft Windows Vista with the
default interface. If you use the Classic interface, where the icons and menus resemble previous
Windows versions, perform the procedure in section 4.4.
1. On the Windows taskbar, click Start, click Control Panel, and then select the Network
and Internet icon.
2. Click View Networks Status and tasks and then click Management Networks
Connections.
3. Right-click the Local Area Connection icon and click Properties.
4. Click Continue. The Local Area Connection Properties dialog box appears.
5. In the Local Area Connection Properties dialog box, verify that Internet Protocol
(TCP/IPv4) is checked. Then select Internet Protocol (TCP/IPv4) and click the Properties
button. The Internet Protocol Version 4 Properties dialog box appears.
6. In the Internet Protocol Version 4 Properties dialog box, click Obtain an IP address
automatically to configure your computer for DHCP.
7. Click the OK button to save your changes and close the dialog box.
8. Click the OK button again to save your changes.
4.3 Configuring Microsoft Windows XP
Use the following procedure to configure a computer running Microsoft Windows XP with the default
interface. If you use the Classic interface, where the icons and menus resemble previous Windows
versions, perform the procedure in section 4.4.
1. On the Windows taskbar, click Start, click Control Panel, and then click Network and
Internet Connections.
2. Click the Network Connections icon.
3. Click Local Area Connection for the Ethernet adapter connected to the OM2P V2. The Local
Area Connection Status dialog box appears.
4. In the Local Area Connection Status dialog box, click the Properties button. The Local
Area Connection Properties dialog box appears.
5. In the Local Area Connection Properties dialog box, verify that Internet Protocol (TCP/IP)
is checked. Then select Internet Protocol (TCP/IP) and click the Properties button. The
Internet Protocol (TCP/IP) Properties dialog box appears.
6. In the Internet Protocol (TCP/IP) Properties dialog box, click Obtain an IP address
automatically to configure your computer for DHCP. Click the OK button to save this
change and close the Internet Protocol (TCP/IP) Properties dialog box.
7. Click the OK button again to save your changes.
8. Restart your computer.
4.4 Configuring Microsoft Windows 2000
Use the following procedure to configure your computer if your computer has Microsoft Windows
2000 installed.
1. On the Windows taskbar, click Start, point to Settings, and then click Control Panel.
2. In the Control Panel window, double-click the Network and Dial-up Connections icon. If
the Ethernet adapter in your computer is installed correctly, the Local Area Connection
icon appears.
3. Double-click the Local Area Connection icon for the Ethernet adapter connected to the
OM2P V2. The Local Area Connection Status dialog box appears.
4. In the Local Area Connection Status dialog box, click the Properties button. The Local
Area Connection Properties dialog box appears.
5. In the Local Area Connection Properties dialog box, verify that Internet Protocol (TCP/IP)
is checked. Then select Internet Protocol (TCP/IP) and click the Properties button.
6. Click Obtain an IP address automatically to configure your computer for DHCP.
7. Click the OK button to save this change and close the Local Area Connection Properties
dialog box.
8. Click OK button again to save these new changes.
9. Restart your computer.
4.5 Configuring an Apple Macintosh Computer
The following procedure describes how to configure TCP/IP on an Apple Macintosh running Mac OS
10.2. If your Apple Macintosh is running Mac OS 7.x or later, the steps you perform and the screens
you see may differ slightly from the following. However, you should still be able to use this procedure
as a guide to configuring your Apple Macintosh for TCP/IP.
1. Pull down the Apple Menu, click System Preferences, and select Network.
2. Verify that the NIC connected to the OM2P V2 is selected in the Show field.
3. In the Configure field on the TCP/IP tab, select Using DHCP.
4. Click Apply Now to apply your settings and close the TCP/IP dialog box.
Chapter 5 Introducing the Web Configurator
The OM2P V2 has a built-in Web Configurator that lets you manage the unit from any location using a
Web browser that supports HTTP and has JavaScript installed.
5.1 Logging in to the Web Configurator
After configuring the computer for TCP/IP using the procedure appropriate for your operating system,
use that computer’s Web browser to log in to the OM2P V2 Web Configurator.
1. Launch your Web browser.
2. In the browser address bar, type 192.168.1.1 and press the Enter key.
If you changed the OM2P V2 LAN IP address, enter the correct IP address.
3. When the Windows Security window appears, type admin as the username in the top field and
type admin as the password in the bottom field.
4. Click OK
You are now ready to use the instructions in the following chapters to configure the OM2P V2.
5.2 Best Practices
Perform the following procedures regularly to make the OM2P V2 more secure and manage the OM2P
V2
more effectively.
Change the default password. Use a password that is not easy to guess and that contains
different characters, such as numbers and letters. The OM2P V2 username cannot be changed.
For more information, see page 69.
Back up the configuration and be sure you know how to restore it. Restoring an earlier working
configuration can be useful if the OM2P V2 becomes unstable or crashes. If you forget your
password, you will have to reset the OM2P V2 to its factory default settings and lose any
customized override settings you configured. However, if you back up an earlier configuration, you
will not have to completely reconfigure the OM2P V2. You can simply restore your last
configuration. For more information, see page 73.
Chapter 6 Status
The Status section on the navigation drop-down menu contains the following options:
- Main
- Wireless Client List
System Log
Connection Status
The following sections describe these options.
6.1 Save/Load
This page lets you save and apply the settings shown under Unsaved changes list, or cancel
the unsaved changes and revert to the previous settings that were in effect.
6.2 Main
Clicking the Main link under the Status drop-down menu or clicking Home at the top-right
of the Web Configurator shows status information about the current operating mode.
The System Information section shows general system information such as operating
mode, system up time, firmware version, serial number, kernel version, and application
version.
The LAN Settings section shows Local Area Network setting such as the LAN IP address,
subnet mask, and MAC address.
The Current Wireless Settings section shows wireless information such as frequency and
channel. Since the OM2P V2 supports multiple-SSIDs, information about each SSID, such
as its ESSID and security settings, are displayed.
6.3 Wireless Client List
Clicking the Wireless Client List link under the Status drop-down menu displays the list of
clients associated to the OM2P V2, along with the MAC addresses and signal strength for
each client. Clicking the Refresh button updates (refreshes) the client list.
6.4 System Log
The OM2P V2 automatically logs (records) events of possìble ìnterest ìn ìts ìnternal
memory.To vìew the logged ìnformatìon click the System Log lìnk under the Status dropdown menu. I睡
there ìs not enough ìnternal memory to log all events older events are deleted from the log.
Home
System Log
JY1
Resel
AII
Oct 19 10:16:58 (none)user.warn kernel: jffs2 build filesystem(): era3ing
rct 19 10:16:58 (none)user.info kernel: mïni fo: sing
3torage directory:
Oct 19 10:16:58 (none)user.info kernel: mïni fo: using base directory:
/ Oct 19 10:16:34 (none)user.warn kernel: jffs2 3can eraseblock(): End
of f
Oct 19 10:16:34 (none)user.warn kernel: jffs2 build filesystem():
unlocki ct 19 10:16:33 (none)user.warn kernel: ar5416SetSwitchCom
ant
3witch co
Oct 19 10:16:33 (none)daemon.info dnsmðsq[823]: using local addresses onl
Oct 19 10:16:33 (none)daemon.info dnsmðsq[823]: using local addresses onl
Oct 19 10:16:33 (none)daemon.info dnsmasq[823): started
ve
i 2.52 cac'---'
Oct 19 10:16:33 (none)daemon.info dnsmasq[823): readinq /
/resolv.conf
Oct 19 10:16:33 (none)daemon.info dnsmasq[823): read /etc/hosts - 1 addre
Oct 19 10:16:33 (none)daemon.info dnsmasq[823): compi1e time options: I惱v
ct 19 10:16:31 (none)user.info kernel: device athO entered promïscuou3
Oct 19 10:16:31 (none)user.info kernel: br-lan: topology change detected
Oct 19 10:16:31 (none)user.info kernel: br-lan: port 3(athO) entering lea
Oct 19 10:16:31 (none)user.info kernel: br-lan: port 3(athO) entering
for ct 19 10:16:30 (none)user.warn kernel: osif vap init : wait for
connecti Oct 19 10:16:30 (none)user.info kernel: device athO left
promïscuou3 mode
Oct 19 10:16:30 (none)user.info kernel: br-lan: port 3(athO) entering
dis ct 19 10:16:25 (none)user.warn kernel: start running
Oct 19 10:16:25 (none)user.warn kernel: set SIOC80211NWID
8 characters
Oct 19 10:16:25 (none)user.warn kernel: osif vap init 'r1akeup from 'r1ait
(I
1 Rerresh 11 Clear l
111
6.5 Conneetion StatU$
Clicking the Connection Status link under the Stat
drop-down menu displays the current
status of the network。 The information shown includes network type SSID BSSID connection
status wireless mode current channel security data rate noise level and signal strength.
Wireless
Netwo
Type
I l司lient Router
SS
ID
IIEnGenius
BSS
ID
Connection S
Wire ss Mode
Current Channel
urity
Tx Da
Ra
Mbps) Current n
se vel S nal
strength
WAN
I Refl:esh I
6.6 DHCP Client Table
Clicking the DHCP Client List link under the Status drop-down menu displays the clients that
are associated to the OM2P V2 through DHCP.The MAC addresses and signal strength for
each
client are also shown. Clicking the Refresh button updates (refreshes) the client list。
Home
DHCP Client list
MAC addr
I Refl:esh I
11
IP
11
Expires
Resel
Chapter 7 System
This chapter describes how to change the OM2P V2 operating modes.
7.1 Changing Operating Modes
The OM2P V2 supports four operating modes:
- Access Point
- Client Bridge
- WDS Bridge
Client Router
To select an operating mode, click System Properties under System Section. Then
go to System > Operation mode.
Device Name: Enter a name for the device. The name you type appears in SNMP
management. This name is not the SSID and is not broadcast to other devices.
Operation Mode: Use the radio button to select an operating mode. To use Access Point
mode with WDS, select Access Point here and then enable the WDS function in the Wireless
Network section (see section 8.6).
Click Accept to confirm the changes.
Clicking Accept does not apply the changes. To apply them use Status > Save/Load (see
section 4.1)
Chapter 8 Wireless Configuration
This chapter describes the OM2P V2’s wireless settings. Please read the information in this
chapter carefully. If you configure a setting improperly, it can impact performance and affect
the network adversely. Before you continue, be sure you selected the appropriate operating
mode (see Chapter 7).
8.1 Wireless Settings
This section describes basic wireless settings. For more information, see Chapter 12.
8.1.1 Access Point Mode
The OM2P V2 supports Access Point Mode. In this mode, users with a wireless client device
within range can connect to the OM2P V2 to access the WLAN. The following figure shows
an example of an OM2P V2 operating in Access Point Mode.
The sections that follow the figure below describe how to configure your OM2P V2 for
Access
Point Mode.
Wireless Mode
Wireless mode supports 802.11b/g/n mixed modes.
Channel HT Mode
The default channel bandwidth is 40 MHz. The larger the channel,
the better the transmission quality and speed.
Extension Channel
Select upper or lower channel. Your selection may affect the Auto
channel function.
Auto
Check this option to enable auto-channel selection.
AP Detection
AP Detection can select the best channel to use by scanning
nearby areas for Access Points.
Current Profile
Configure up to four different SSIDs. If many client devices will be
accessing the network, you can arrange the devices into SSID
groups. Click Edit to configure the profile and check whether you
want to enable extra SSID.
Profile Isolation
Restricted Client to communicate with different VID by Selecting
the radio button.
Accept / Cancel
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see
section 4.1).
SSID
Specify the SSID for the current profile.
VLAN ID
Specify the VLAN tag for the current profile.
Suppressed SSID
Check this option to hide the SSID from clients. If checked, the
SSID will not appear in the site survey.
Station Separation
Click the appropriate radio button to allow or prevent
communication between client devices.
Wireless Security
See the Wireless Security section.
Save / Cancel
Click Save to accept the changes or Cancel to cancel and return
previous settings.
8.1.2 Client Bridge Mode
Client Bridge Mode lets you connect two LAN segments via a wireless link as though they are
on the same physical network. Since the computers are on the same subnet, broadcasts will
reach all machines. As a result, DHCP information generated by the server will reach all client
computers as though the clients resided on one physical network.
The following figure shows an example of an OM2P V2 communicating with an Access
Point/Wireless Router, such as the EnGenius EOA7530, operating in Client Bridge Mode.
The sections that follow the figure below describe how to configure your OM2P V2 for Client
Bridge Mode.
Wireless Mode
Wireless mode supports 802.11b/g/n mixed modes.
SSID
Specify the SSID if known. This field is completed automatically if
you select an Access Point in the Site Survey.
Site Survey
Scans nearby locations for Access Points. You can select a
discovered Access Point to establish a connection.
Prefer BSSID
Enter the MAC address if known. If you select an Access Point in
the Site Survey, this field is completed automatically.
WDS Client
Click the appropriate radio button to enable or disable WDS
Client.
Wireless Security
See section 8.2 for information.
Accept / Cancel
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see
section 4.1).
Profile
If you used the Site Survey, the Web Configurator shows nearby
Access Points. To connect to an Access Point, click the Access
Point’s BSSID.
Wireless Security
See the Wireless Security section.
Refresh
Click Refresh to scan again.
If the Access Point has been configured to suppress its SSID, the SSID section will be blank
and must be completed manually.
8.1.3 WDS Bridge Mode
Unlike traditional bridging. WDS Bridge Mode allows you to create large wireless networks by
linking several wireless access points with WDS links. WDS is normally used in large, open
areas, where pulling wires is cost prohibitive, restricted or physically impossible.
The following figure shows an example of three OM2P V2 configured for WDS Bridge Mode
communicating with each other. In this configuration, the OM2P V2 device on the left side of
the figure behaves as a standard bridge that forwards traffic between the WDS links (links
that connect to other OM2P V2 WDS bridges).
The sections that follow the figure below describe how to configure your OM2P V2 for
WDS Bridge Mode.
Wireless Mode
Wireless mode supports 802.11b/g/n mixed modes.
Channel HT Mode
The default channel bandwidth is 40 MHz. The larger the channel,
the better the transmission quality and speed.
Extension Channel
Select upper or lower channel. Your selection may affect the Auto
channel function.
Accept / Cancel
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see
section 4.1).
MAC Address
Enter the MAC address of the Access Point to which you want to
extend wireless connectivity.
Mode
Select Disable or Enable to disable or enable WDS.
Accept / Cancel
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
1. Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see
section 4.1).
2. The Access Point to which you want to extend wireless connectivity must enter the OM2P
V2’s MAC address into its configuration. For more information, refer to the documentation for
the Access Point. Not all Access Point supports this feature.
8.1.4 Client Router Mode
In Client Router Mode, you can access the Internet wirelessly with the support of a WISP. In AP
Router Mode, the OM2P V2 can access the Internet via a cable or DSL modem. In this mode,
the OM2P V2 can be configured to turn off the wireless network name (SSID) broadcast, so
that only stations that have the SSID can be connected. The OM2P V2 also provides wireless
LAN
64/128/152-bit WEP encryption security, WPA/WPA2, and WPA-PSK/WPA2-PSK authentication,
as well as TKIP/AES encryption security. It also supports VPN pass-through for sensitive data
secure transmission.
The following figure shows an example of an OM2P V2 communicating with a Wireless ISP
(WISP) Access Point in Client Router Mode. The sections that follow the figure below describe
how to configure your OM2P V2 for Client Router Mode.
Wireless Mode
Wireless mode supports 802.11b/g/n mixed modes.
SSID
Specify the SSID if known. This field is completed automatically if
you select an Access Point in the Site Survey.
Site Survey
Scans nearby locations for Access Points. You can select a
discovered Access Point to establish a connection.
Prefer BSSID
Enter the MAC address if known. If you select an Access Point in
the Site Survey, this field is completed automatically.
Wireless Security
See section 10.2.
Accept / Cancel
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see
section 4.1).
Profile
If you used the Site Survey, the Web Configurator shows nearby
Access Points. To connect to an Access Point, click the Access
Point’s BSSID.
Wireless Security
See the Wireless Security section.
Refresh
Click Refresh to scan again.
If the Access Point has been configured to suppress its SSID, the SSID section must be
completed manually.
8.2 Wireless Security Settings
The Wireless Security Settings section lets you configure the EOH200’s security modes: WEP,
WPA-PSK, WPA2-PSK, WPA-PSK Mixed, WPA, WPA2, and WPA Mixed. We strongly
recommend you use WPA2-PSK.
8.2.1 WEP
Security Mode
Select WEP from the drop-down list to begin the configuration.
Auth Type
Select Open System or Shared.
Input Type
Select an input type of Hex or ASCII.
Key Length
Level of WEP encryption applied to all WEP keys. Choices are
Select a 64/128/152-bit password lengths.
Default Key
default.
Specify which of the four WEP keys the OM2P V2 uses as its
Key1
Specify a password for security key index No.1. For security, each
typed character is masked by a dot (l).
Key2
Specify a password for security key index No.2. For security, each
typed character is masked by a dot (l).
Key3
Specify a password for security key index No.3. For security, each
typed character is masked by a dot (l).
Key4
Specify a password for security key index No.4. For security, each
typed character is masked by a dot (l).
802.11n does not allow WEP/WPA-PSK/WPA-PSK TKIP security mode. The connection mode
will drop from 802.11n to 802.11g.
8.2.2 WPA-PSK
Security Mode
Select WPA-PSK from the drop-down list to begin the
configuration.
Encryption
Select Both, TKIP, or AES as the encryption type.
• Both = uses TKIP and AES.
Passphrase
•
TKIP = automatic encryption with WPA-PSK; requires
passphrase.
•
AES = automatic encryption with WPA2-PSK; requires
passphrase.
Specify the security password. For security, each typed character
is masked by a dot (l).
Group Key Update
Interval
Specify how often, in seconds, the group key changes.
802.11n does not allow WEP/WPA-PSK/WPA-PSK TKIP security mode. The connection mode
will drops from 802.11n to 802.11g.
8.2.3 WPA2-PSK
Security Mode
Select WPA2-PSK from the drop-down list to begin the
configuration.
Encryption
Select Both, TKIP, or AES as the encryption type.
•
Both = uses TKIP and AES.
Passphrase
•
TKIP = automatic encryption with WPA-PSK; requires
•
passphrase.
AES = automatic encryption with WPA2-PSK; requires
passphrase.
Specify the security password. For security, each typed character
is masked by a dot (l).
Group Key Update
Interval
Specify how often, in seconds, the group key changes.
802.11n does not allow WEP/WPA-PSK/WPA-PSK TKIP security mode. The connection mode
will change from 802.11n to 802.11g.
8.2.4 WPA-PSK Mixed
Security Mode
Select WPA-PSK Mixed from the drop-down list to begin the
configuration.
Encryption
Select Both, TKIP, or AES as the encryption type.
•
Both = uses TKIP and AES.
Passphrase
•
TKIP = automatic encryption with WPA-PSK; requires
passphrase.
•
AES = automatic encryption with WPA2-PSK; requires
passphrase.
Specify the security password. For security, each typed character
is masked by a dot (l).
Group Key Update
Interval
Specify how often, in seconds, the group key changes.
WPA-PSK Mixed can allow multiple security modes at the same time.
802.11n does not allow WEP/WPA-PSK/WPA-PSK TKIP security mode. The connection mode
will change from 802.11n to 802.11g.
8.2.5 WPA
Security Mode
Select WPA from the drop-down list to begin the configuration.
Encryption
Select Both, TKIP, or AES as the encryption type.
•
Both = uses TKIP and AES.
•
•
TKIP = automatic encryption with WPA-PSK.
AES = automatic encryption with WPA2-PSK.
Radius Server
Specify the IP address of the RADIUS server.
Radius Port
Specify the port number that your RADIUS server uses for
authentication. Default port is 1812.
Radius Secret
Specify RADIUS secret furnished by the RADIUS server.
Group Key Update
Interval
Specify how often, in seconds, the group key changes.
802.11n does not allow WEP/WPA-PSK/WPA-PSK TKIP security mode. The connection mode
will drops from 802.11n to 802.11g.
8.2.6 WPA2
Security Mode
Select WPA2 from the drop-down list to begin the configuration.
Encryption
Select Both, TKIP, or AES as the encryption type.
•
Both = uses TKIP and AES.
•
•
TKIP = automatic encryption with WPA-PSK.
AES = automatic encryption with WPA2-PSK.
Radius Server
Specify the IP address of the RADIUS server.
Radius Port
Specify the port number that your RADIUS server uses for
authentication. Default port is 1812.
Radius Secret
Specify RADIUS secret furnished by the RADIUS server.
Group Key Update
Interval
Specify how often, in seconds, the group key changes.
802.11n does not allow WEP/WPA-PSK/WPA-PSK TKIP security mode. The date rate will drop
from 802.11n to 802.11g.
8.2.7 WPA Mixed
Security Mode
Select WPA Mixed from the drop-down list to begin the
configuration.
Encryption
Select Both, TKIP, or AES as the encryption type.
•
Both = uses TKIP and AES.
•
•
TKIP = automatic encryption with WPA-PSK.
AES = automatic encryption with WPA2-PSK.
Radius Server
Specify the IP address of the RADIUS server.
Radius Port
Specify the port number that your RADIUS server uses for
authentication. Default port is 1812.
Radius Secret
Specify RADIUS secret furnished by the RADIUS server.
Group Key Update
Interval
Specify how often, in seconds, the group key changes.
802.11n does not allow WEP/WPA-PSK/WPA-PSK TKIP security mode. The connection mode
will change from 802.11n to 802.11g.
8.4 Wireless Advanced Settings
Data Rate
Select a data rate from the drop-down list. The data rate affects
throughput. If you select a low data rate value, for example, the
throughput is reduced but the transmission distance increases.
RTS/CTS Threshold
Specify the threshold package size for RTC/CTS. A small number
causes RTS/CTS packets to be sent more often and consumes
more bandwidth.
Distance
Specify the distance between Access Points and clients. Longer
distances may drop high-speed connections.
Antenna Selection
Specify the internal antenna type.
Short GI
Sets the time that the receiver waits for RF reflections to settle out
before sampling data. Using a short (400ns) guard interval can
increase throughput, but can also increase error rate in some
installations due to increased sensitivity to radio-frequency
reflections. Select the option that works best for your installation.
Aggregation
Merges data packets into one packet. This option reduces the
number of packets, but increases packet sizes.
Wireless Traffic
Shaping
Check this option to enable wireless traff ic shaping. Traffic
shaping regulates the flow of packets leaving an interface to
deliver improved Quality of Service.
Incoming Traffic Limit
Specify the wireless transmission speed used for downloading.
Outgoing Traffic Limit
Specify the wireless transmission speed used for uploading.
Accept / Cancel
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
1. Changing Wireless Advanced Settings may adversely affect wireless performance. Please
accept all default settings, unless you are familiar with the wireless options.
2. Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see
section 4.1).
8.5 Wireless MAC Filter
Wireless MAC Filters are used to allow or deny network access to wireless clients according to
their MAC addresses. You can manually add a MAC address to restrict the permission to
access OM2P V2. The default setting is Disable Wireless MAC Filters.
0.
ACL Mode
Determines whether network access is granted or denied to
clients whose MAC addresses appear in the MAC Address table
on this page. Choices are Disable, Deny MAC in the list, or
Allow MAC in the list.
MAC Address Filter
Enter the MAC address of the device.
Add
Click Add to add the MAC address to the MAC Address table.
Apply
Click Apply to apply the changes.
8.6 WDS Link Settings
Using WDS Link Settings, you can create a wireless backbone link between multiple access
points that are part of the same wireless network. This allows a wireless network to be
expanded using multiple Access Points without the need for a wired backbone to link them, as
is traditionally required.
MAC Address
Enter the Access Point’s MAC address to which you want to
extend the wireless area.
Mode
Select Disable or Enable from the drop-down list.
Accept / Cancel
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see
section 4.1).
The Access Point to which you want to extend wireless connectivity must enter the OM2P V2’s
MAC address into its configuration. For more information, refer to the documentation for the
Access Point. Not all Access Point supports this feature.
Chapter 9 LAN Setup
This chapter describes the OM2P V2 Local Area Network (LAN) settings.
9.1 IP Settings
This section is only available for Non-Router Mode. IP settings lets you configure the OM2P
V2 LAN port IP address.
IP Network Setting
Select whether the OM2P V2 IP address will use the static IP
address specif ied in the IP Address field or be obtained
automatically when the OM2P V2 connects to a device that has a
DHCP server .
IP Address
Enter the IP address of the OM2P
V2. IP Suet Mask
Enter the OM2P V2 subnet mask.
Default Gateway
Enter the OM2P V2 default
gateway. Primary DNS
Enter the OM2P V2 primary DNS.
Secondary DNS
Enter the OM2P V2 secondary
DNS.
Accept / Cancel
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
If you change the LAN IP address, you will be directed to the new IP address after you click
Apply.
9.2 Spanning Tree Settings
Spanning Tree Status
Enable or disable the OM2P V2 Spanning Tree function.
Bridge Hello Time
Specify Bridge Hello Time, in seconds. This value determine how
often the OM2P V2 sends hello packets to communicate
information about the topology throughout the entire Bridged
Local Area Network
Bridge Max Age
Specify Bridge Max Age, in seconds. If another bridge in the
spanning tree does not send a hello packet for a long period of
time, it is assumed to be dead.
Bridge Forward Delay
Specify Bridge Forward Delay, in seconds. Forwarding delay time
is the time spent in each of the Listening and Learning states
before the Forwarding state is entered. This delay is provided so
that when a new bridge comes onto a busy network, it looks at
some traffic before participating.
Priority
Specify the Priority number. Smaller number has greater priority.
Accept / Cancel
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see
section 4.1).
Chapter 10 Router Settings
This section is only available for AP Router Mode and Client Router Mode.
10.1 WAN Settings
This chapter describes the OM2P V2 WAN settings. There are four types of WAN
connections:
- Static IP
- DHCP
- PPPoE
PPTP
Please contact your ISP to find out which settings you should choose..
10.1.1 Static IP
Select Static IP for your WAN connection if your ISP provided information about which IP
address, subnet mask, default gateway, primary DNS, and secondary DNS to use.
Internet Connection
Type
Select Static IP to begin configuration of the Static IP connection.
Account Name
Enter the account name provided by your ISP.
Domain Name
Enter the domain name provided by your ISP.
MTU
Specify the Maximum Transmit Unit size. It is recommended you
accept the default setting of Auto. Otherwise, packets will be
fragmented downstream if the MTU is set too high or too low,
which impacts network performance. In extreme cases, an MTU
setting that is too low can prevent the OM2P V2 from
establishing some connections.
IP Address
Enter the WAN port IP address. IP
Subnet Mask
Enter the WAN IP subnet mask.
Gateway IP Address
Enter the WAN gateway IP address.
Primary DNS
Enter the primary DNS IP address.
Secondary DNS
Enter the secondary DNS IP address.
Discard Ping on WAN
Check to Enable to recognize pings on the OM2P V2 WAN
interface or Disable to block pings on the OM2P V2 WAN
interface. Note: Pinging IP addresses is a common method used
by hackers to
test whether the IP address is valid. Blocking pings provides some
extra security from hackers.
Accept / Cancel
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see
section 4.1).
10.1.2 DHCP (Dynamic IP)
Select DHCP as your WAN connection type to obtain an IP address automatically. You will
need to enter account name as your hostname and, optionally, DNS information.
Internet Connection
Type
Select DHCP to begin configuration of the DHCP connection.
Account Name
Enter the account name provided by your ISP.
Domain Name
Enter the domain name provided by your ISP.
MTU
Specify the Maximum Transmit Unit size. It is recommended you
accept the default setting of Auto. Otherwise, packets will be
fragmented downstream if the MTU is set too high or too low,
which impacts network performance. In extreme cases, an MTU
setting that is too low can prevent the OM2P V2 from
establishing some connections.
Get Automatically
From ISP
Click this radio button to obtain the DNS automatically from the
DHCP server.
Use These DNS Servers
Click the radio button to set up the Primary DNS and Secondary
DNS servers manually.
Discard Ping on WAN
Check to Enable to recognize pings on the OM2P V2 WAN
interface or Disable to block pings on the OM2P V2 WAN
interface. Note: Pinging IP addresses is a common method used
by hackers to
test whether the IP address is valid. Blocking pings provides some
extra security from hackers.
Accept / Cancel
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see
section 4.1).
10.1.3 PPPoE (Point-to-Point Protocol over Ethernet)
Select Point to Point Protocol over Ethernet (PPPoE) if  your ISP uses a PPPoE connection.
Your ISP will provide you with a username and password. This selection is typically used for
DSL services. Remove your PPPoE software from your computer, as it is not needed and will
not work with your OM2P
V2.
Internet Connection
Type
MTU
Select PPPoE to begin configuration of the PPPoE connection.
Specify the Maximum Transmit Unit size. It is recommended you
accept the default setting of Auto. Otherwise, packets will be
fragmented downstream if the MTU is set too high or too low,
which impacts network performance. In extreme cases, an MTU
setting that is too low can prevent the OM2P V2 from
establishing some connections.
Login
Enter the Username provided by your ISP.
Password
Enter the Password provided by your ISP.
Service Name
Enter the Service Name provided by your ISP.
Connect on Demand
Select the radio button to specify the maximum idle time.
Internet connection will disconnect when it reach the maximum
idle time, but it will automatically connect when user tries to
access the network.
Keep Alive
Select whether to keep the Internet connection always on, or
enter a redial period once the internet lose connection.
Get Automatically
From ISP
Select whether to obtain the DNS automatically from the DHCP
server.
Use These DNS Servers
Click the radio button to set up the Primary DNS and Secondary
DNS servers manually.
Discard Ping on WAN
Check to Enable to recognize pings on the OM2P V2 WAN
interface or Disable to block pings on the OM2P V2 WAN
interface. Note: Pinging IP addresses is a common method used
by hackers to
test whether the IP address is valid. Blocking pings provides some
extra security from hackers.
Accept / Cancel
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see
section 4.1).
10.1.4 PPTP (Point-to-Point Tunneling Protocol)
Select PPTP as your WAN connection type if your ISP uses a Point-to-Point-Tunneling Protocol
(PPTP) connection. You will need to provide the IP address subnet mask default gateway
(optional) DNS (optional) server IP usernam
e and password provided by your ISP.
Home
WAN Settings
Resel
!il UseTheseDNS Serve
|o
!。Io !。Io !。Io
WAN Ping
PingonWAN
I Apply I
Internet Connection
Type
Select PPTP to begin config uration of the PPTP connection.
MTU
Specify the Maximum Transmit Unit size. It is recommended you
accept the default setting of Auto. Otherwise, packets will be
fragmented downstream if the MTU is set too high or too low,
which impacts network performance. In extreme cases, an MTU
setting that is too low can prevent the OM2P V2 from
establishing some connections.
IP Address
Enter the WAN port IP address. IP
Subnet Mask
Enter the WAN IP subnet mask.
Gateway IP Address
Enter the WAN gateway IP address.
PPTP Server
Enter the IP address of the PPTP server.
Username
Enter the username provided by your ISP.
Password
Enter the password provided by your ISP.
Connect on Demand
If you want the OM2P V2 to end the Internet connection after it
has been inactive for a period of time, select this option and enter
the number of minutes you want that period of inactivity to last.
Keep Alive
If you want the OM2P V2 to periodically check your Internet
connection, select this option. Then specify how often you want
the OM2P V2 to check the Internet connection. If the
connection is
down, the OM2P V2 automatically re-establishes your connection
Get Automatically
From ISP
Obtains the DNS automatically from DHCP server.
Use These DNS Servers
Click the radio button to set up the Primary DNS and Secondary
DNS servers manually.
Discard Ping on WAN
Check to Enable to recognize pings on the OM2P V2 WAN
interface or Disable to block pings on the OM2P V2 WAN
interface. Note: Pinging IP addresses is a common method used
by hackers to
test whether the IP address is valid. Blocking pings provides some
extra security from hackers.
Accept / Cancel
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see
section 4.1).
10.2 LAN Settings (Router Mode)
IP Address
Enter the LAN port IP address.
IP Subnet Mask
Enter the LAN IP subnet mask.
WINS Server IP
Enter the WINS Server IP.
Use Router As DHCP
Server
Check this option to enable the OM2P V2 internal DHCP server.
Starting IP Address
Specify the starting IP address range for the pool of allocated for
private IP addresses. The starting IP address must be on the same
subnet as the ending IP address; that is the first three octets
specif ied here must be the same as the first three octets in End
IP Address.
Ending IP Address
Specify the ending IP address range for the pool of allocated for
private IP addresses. The ending IP address must be on the same
subnet as the starting IP address; that is the first three octets
specif ied here must be the same as the first three octets in Start
IP Address.
WINS Server IP
Enter the IP address of the WINS server.
Accept / Cancel
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see
section 4.1).
10.3 VPN Pass Through
VPN Passthrough allows a secure virtual private network (VPN) connection between two
computers. Enabling the options on this page opens a VPN port and enables connections to
pass through the OM2P V2 without interruption.
PPTP Pass Through
Check this option to enable PPTP pass-through mode.
L2TP Pass Through
Check this option to enable L2TP pass-through mode.
IPSec Pass Through
Check this option to enable IPSec pass-through mode.
Accept / Cancel
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see
section 4.1).
10.4 Port Forwarding
Port forwarding can be used to open a port or range of ports to a device on your network
Using port forwarding, you can set up public services on your network. When users from the
Internet make certain requests on your network, the OM2P V2 can forward those requests to
computers equipped to handle the requests. If, for example, you set the port number 80
(HTTP) to be forwarded to IP address 192.168.1.2, all HTTP requests from outside users are
forwarded to 192.168.1.2.
Add Entry
Click Add Entry to add port forwarding rules.
Accept
Click Accept to confirm the changes.
Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see
section 4.1).
Service Name
Enter a name for the port forwarding rule.
Protocol
Select a protocol for the application: Choices are Both, TCP, and
UDP.
Starting Port
Enter a starting port number.
Ending Port
Enter an ending port number. All ports numbers between the
starting and ending ports will forward users to the IP address
specif ied in the IP Address field.
IP Address
Enter the IP address of the server computer on the LAN network
where users will be redirected.
Save / Cancel
Click Save to apply the changes or Cancel to return previous
settings.
10.5 DMZ
If you have a computer that cannot run Internet applications properly from behind the OM2P
V2, you can allow the computer to have unrestricted Internet access. Enter the IP address of
that computer as a Demilitarized Zone (DMZ) host with unrestricted Internet access. Adding a
client to the DMZ may expose that computer to a variety of security risks, so use this option as
a last resort.
DMZ Hosting
Enables or disables the OM2P V2 DMZ function.
DMZ Address
Enter an IP address of the computer that will have unlimited
Internet access.
Accept / Cancel
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see
section 4.1).
Chapter 11 Management Settings
The Management section lets you configure administration, management VLAN, SNMP
settings, backup/restore settings, firmware upgrade, time settings, and log settings. This
chapter describes these settings.
11.1 Administration
Click the Administration link under the Management menu to change the user name and
password used to log on to the OM2P V2 Web Configurator . The default user name is admin
and the default password is admin. Changing these settings protects the OM2P V2
configuration settings from being accessed by unauthorized users.
Name
Enter a new username for logging in to the Web Configurator.
Password
Enter a new password for logging in to the Web Configurator
Confirm Password
Re-enter the new password for confirmation.
Remote Management
Enable or disable remote management.
Remote Upgrade
Specify whether the OM2P V2 firmware can be upgraded remotely.
Remote Management
Port
If remote management is enabled, enter the port number to be
used for remote management. For example: If you specify the
port number 8080, enter http://:8080 to access
the OM2P V2 Web Configurator.
Save/Apply / Cancel
Click Save/Apply to apply the changes or Cancel to return
previous settings.
Clicking Save/Apply changes the settings immediately. You cannot undo the action.
11.2 Management VLAN
Click the Management VLAN link under the Management menu to assign a VLAN tag to the
packets. A VLAN is a group of computers on a network whose software has been configured
so that they behave as if they were on a separate Local Area Network (LAN). Computers on
VLAN do not have to be physically located next to one another on the LAN
Management VLAN ID
If your network includes VLANs and if tagged packets need to
pass through the Access Point, enter the VLAN ID. Otherwise,
click No VLAN tag .
Accept / Cancel
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
1. If you reconfigure the Management VLAN ID, you may lose your connection to the OM2P
V2. Verify that the DHCP server supports the reconfigured VLAN ID and then reconnect to
the OM2P V2 using the new IP address.
2. Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see
section 4.1).
11.3 SNMP Settings
Click the SNMP Settings link under the Management menu to monitor network-attached
devices using the Simple Network Management Protocol (SNMP). SNMP allows messages
(called “protocol data unit’s) to be sent to various parts of a network. Upon receiving these
messages, SNMP-compatible devices (called agents) return data stored in their Management
Information Bases.
SNMP Enable/Disable
Enable or disable the OM2P V2 SNMP
function. Contact
Enter the contact details of the device.
Location
Enter the location of the device.
Community Name
Enter the password for accessing the SNMP community for
read-only access.
Community Name
Enter the password for accessing the SNMP community for read
and write access.
Trap Destination IP
Address
Enter the IP address where SNMP traps are to be sent.
Trap Destination
Community Name
Enter the password of the SNMP trap community.
Save/Apply / Cancel
Click Save/Apply to apply the changes or Cancel to return
previous settings.
Clicking Save/Apply change the setting immediately. You cannot undo the action.
11.4 Backup/Restore Settings
Click the Backup/Restore Setting link under the Management menu to save the OM2P
V2’s current settings in a file on your local disk or load settings onto the device from a local
disk. This feature is particularly convenient administrators who have several OM2P V2
devices that need to be configured with the same settings.
This page also lets you return the OM2P V2 to its factory default settings. If you perform
this procedure, any changes made to the OM2P V2 default settings will be lost.
Save A Copy of Current Click Backup to save the current configured settings.
Settings Restore Saved
Settings from a File
Revert to Factory
Default Settings
To restore settings that have been previously backed up, click
Browse, select the file, and click Restore.
Click this button to restore the OM2P V2 to its factory
default settings.
11.5 Firmware Upgrade
Click the Firmware Upgrade link under the Management menu to upgrade the firmware of
the device. To perform this procedure, downloaded the appropriate firmware from your
vendor.
The firmware upgrade procedure can take few minutes. Do not power off the OM2P V2 during
the firmware upgrade, as it can cause the device to crash or become unusable. The OM2P V2
restarts automatically after the upgrade completes.
11.6 Time Settings
Click the Time Settings link under the Management menu to configure the OM2P V2
system time. You can enter the time manually or, to ensure accuracy, synchronize the
OM2P V2 with
Network Time Protocol (NTP) server.
Manually Set Date and
Time
Manually specify the date and time.
Automatically Get
Select a time zone from the drop-down list and check whether
Date and Time
you want to enter the IP address of an NTP server or use the
default NTP server.
Save/Apply / Cancel
Click Save/Apply to apply the changes or Cancel to return
previous settings.
Clicking Save/Apply changes the setting immediately. You cannot undo the action.
11.7 Log
Click the Log link under the Management menu to display a list of events that are triggered
on the OM2P V2 Ethernet and wireless interfaces. You can consult this log if an unknown
error occurs on the system or when a report needs to be sent to the technical support
department
for debugging purposes.
Syslog
Enable or disable the OM2Psyslog function.
Log Server IP Address
Enter the IP address of the log server.
Local Log
Enable or disable the local log service.
Save/Apply / Cancel
Click Save/Apply to apply the changes or Cancel to return
previous settings.
Clicking Save/Apply changes the settings immediately. You cannot undo the action.
11.8 Diagnostics
Click the Diagnostics link under the Management menu to ascertain connection quality and
trace the routing table to the target.
Target IP
Enter the IP address you would like to search.
Ping Packet Size
Enter the packet size of each ping.
Number of Pings
Enter the number of times you want to ping.
Start Ping
Click Start Ping to begin pinging.
Traceroute Target
Enter an IP address or domain name you want to trace.
Start Traceroute
Click Start Traceroute to begin the trace route operation.
Chapter 12 Network Configuration Examples
This chapter provides step-by-step descriptions for using the OM2P V2’s operating modes.
The Access Point Mode’s default configuration allows the OM2P V2 to act as a central unit of
a WLAN or as a root device of a wired environment. Repeater mode and Mesh network mode
are reserved for future configuration.
12.1 Access Point
Access Point
Step1
Log in to the Web Configurator with your browser by entering
the default IP address 192.168.1.1
Step2
Use site survey to scan channels available in nearby areas.
Step3
Select channel with less interferences.
Step4
Specify the SSID for your broadcast SSID and you can also
configure multiple SSID at the same time.
Step5
Verify the VLAN identif ier to separate services among clients
Step6
Set the authentication settings.
Step7
Click Apply to save all changes.
For more advanced settings, refer to the previous chapters.
Wireless Client
Step1
Select the wireless mode with which you want to associate.
Use site survey to scan nearby Access Point and either select the
Step2
Access Point to which you want to connect, or enter the SSID
manually.
Step3
Configure the VLAN ID in your wireless device if available.
Step4
Select the appropriate authentication type and password.
Access Point Mode does not provide DHCP server, so the Wireless Client IP address
must be configured manually using the same Local Area Network subnet.
12.2 Client Bridge Mode
Client Bridge Mode functions like a wireless dongle. It must connect to an Access Point/AP
Router to join the network.
Refer to Chapter 13 to check the Access Point’s configuration.
Client Bridge
Step1
Log in to the Web Configurator with the default IP address
192.168.1.1
Step2
For Operation Mode, select Client Bridge from System
Properties.
Step3
Use site survey to scan Access Points that are available in nearby
areas.
Step4
Select the Access Point with which you want to associate.
Step5
Set up the authentication settings that match the Access Point’s
settings.
Step6
Click Apply to save all changes.
The Client Bridge IP settings must match the Access Point’s subnet.
12.3 WDS Bridge Mode
Use this feature to link multiple Access Points in a network. All clients associated with any
Access Points can communicate with each other in an ad-hoc manner.
WDS Bridge
Step1
Log in to the Web Configurator with the default IP address
192.168.1.1
Step2
For Operation Mode, select WDS Bridge from System
Properties.
Step3
Select the channel you want to use.
Step4
Set up the authentication settings
Step5
Set up WDS Link Settings.
Step6
Specify the MAC address of the Access Point with which you want
to connect.
Step7
Click Apply to save all changes.
Each WDS bridge device must use the same Subnet, Wireless Mode, Wireless
Channel, and Security Setting.
12.4 Client Router
In Client Router Mode, the OM2P V2’s internal DHCP server allows LANs to automatically
generate an IP address to share the same Internet. Connect an Access Point/WISP wirelessly
and connect to LANs using a wired connection.
Refer to Chapter 13 to check the Access Point’s configuration.
Client Router
Step1
Log in to the Web Configurator with the default IP address
192.168.1.1
Step2
For Operation Mode, select Client Router from System
Properties.
Step3
Change your Local Area Network setting to Obtain an IP
Address Automatically.
Step4
Use site survey to scan Access Points that are available in nearby
areas.
Step5
Select the Access Point with you want to associate.
Step6
Set up authentication settings that match the Access Point’s
settings.
Step7
Step8
Set your WAN connection type using the WAN settings provided
by your ISP.
Click Apply to save all changes.
Client Router’s IP setting must match to the Access Point’s subnet.
Chapter 13 Building a Wireless Network
With its ability to operate in various operating modes, your OM2P V2 is the ideal device
around which you can build your WLAN. This appendix describes how to build a WLAN
around your OM2P V2 using he device’s operating modes.
13.1 Access Point Mode
In Access Point Mode, OM2P V2 behaves likes a central connection for stations or clients that
support IEEE 802.11b/g/n networks. Stations and client must be conf igured to use the same
SSID and security password to associate with the OM2P V2. The OM2P V2 supports four SSIDs
at the same time for secure guest access.
13.2 Access Point Mode with WDS Function
The OM2P V2 Access Point Mode also supports WDS functionality. This operating mode
allows wireless connections to the OM2P V2 using WDS technology. In this mode, conf igure
the MAC addresses in both Access Points to enlarge the wireless area by enabling WDS Link
settings. WDS supports eight AP MAC addresses.
Not every Access Point device supports WDS in Access Point Mode. As a result, to use WDS,
we recommend you use the OM2P V2.
13.3 Client Bridge Mode
In Client Bridge Mode, the OM2P V2 behaves like a wireless client that connects to an Access
Point wirelessly and allows users to surf the Internet whenever they want. In this mode, use
the OM2P V2 Site Survey to scan for Access Points within range. Then configure the OM2P
V2 SSID and security password accordingly to associate with the Access Point. In this
configuration, the station has a wired Ethernet connection to the OM2P V2 LAN port.
13.4 WDS Bridge Mode
In WDS Bridge Mode, the OM2P V2 can wirelessly connect different LANs by configuring the
MAC address and security settings of each OM2P V2 device. Use this mode when two wired
LANs located a small distance apart want to communicate with each other. The best solution
is to use the OM2P V2 to wirelessly connect two wired LANs, as shown in the following figure.
WDS Bridge Mode can establish 16 WDS links, creating a star-like network.
WDS Bridge Mode is unlike Access Point. Access Points linked by WDS are using the same
frequency channel, more Access Points connected together may lower throughput. Please be
aware to avoid loop in your wireless connection, otherwise enable Spanning Tree Function.
13.5 Client Router Mode
In Client Router Mode, the OM2P V2’s internal DHCP server allows a number of LANs to
automatically generate IP addresses to share the same Internet. In this mode, connect an
AP/WISP wirelessly and connect to LANs via a wired connection.
13.6 RADIUS Connections
Remote Authentication Dial In User Service (RADIUS) authentication is available when
configuring the OM2P V2 wireless advanced settings (see Chapter 8). Use this feature if you
have a RADIUS server. WPA(TKIP), WPA2(AES), and WPA2 Mixed encryption types are also
supported.
The following figure shows an example of a RADIUS configuration, where two OM2P V2
devices installed at different locations communicate with each other wirelessly. In this
configuration, one OM2P V2 is configured for Access Point Mode and connected to a RADIUS
server via a switch, while the other OM2P V2 is configured for Client Bridge Mode. The
RADIUS server uses an authentication scheme such as PAP or CHAP to verify a user's
identification, along with, optionally, other information related to the request, such as the
user's network address or phone number, account status and specif ic network service access
privileges. The RADIUS server then returns one of three responses to the OM2P V2 : Access
Reject (user is denied access to all requested network resources), Access Challenge (requests
additional information from the user such as a secondary password), PIN, token or card), or
Access Accept (user is granted access).
Appendix A – Troubleshooting
This appendix provides problem-solving information you may find useful in case you need to
troubleshoot your OM2P V2. It also includes information about contacting technical support.
A.1 Problem Solving
Question
Answer
How do I reset the OM2P V2?
There are two ways to reset the OM2P V2, a
hardware method and a software method. Both
methods return the OM2P V2 to its factory
default configuration.
To use the hardware method, open the cover
on the bottom panel of the OM2P V2 and find
the Reset button (see section 2.1). Using a flat
object such as a pencil, press the Reset button
for approximately 10 seconds and then stop
pressing.
To use the software method, click Restore to
Factory Default in the Management menu.
Why do I not see traffic pass after I connect the
OM2P V2 to a PoE switch?
The OM2P V2 uses a proprietary PoE injector
and will not work with standard 802.3afcompliant
What is the default IP address of the OM2P V2?
The default IP address is 192.168.1.1
I plugged the PoE to the second Ethernet port
on the back of OM2P V2 but the unit is not
on, how come?
You need to plug the Ethernet cable connect to
PoE injector to the main LAN port. The
secondary Ethernet port is just an additional
LAN port for regular Ethernet connection such
as IP camera
When I install the PoE connection to the OM2P
V2, what kind of PoE should I use?
The OM2P V2 uses a proprietary PoE injector
and will not work with standard 802.3afcompliant
I want to use higher gain antennas on the
OM2P V2, but I don’t know what antenna is
right.
I want to buy a high-gain antenna for the
Use the antenna appropriate for the frequency.
(2.4 GHz)
Use an antenna with a SMA connector to
connect to the OM2P V2.
OM2P V2, but I don’t know what type of
antenna and RF connector to buy.
85
A.2 Contacting Technical Support
If you encounter issues that cannot be resolved using this manual, please contact your vendor where you
purchase the device. If you cannot contact your vendor, you may also contact EnGenius Customer Service
department in the region where you purchased the device.
Before you contact your local EnGenius office, please prepare the following information:
Product model name and serial number
The place where you purchased the product
Warranty information
The date when you received the product
A brief description about the issue and the attempts you tried to resolve it
To contact EnGenius Customer Service office in the United States, please use either of the following methods:
Email: Support@EnGeniustech.com
Telephone: 1-888-735-7888
Appendix C – Glossary
Access Point
A base station in a WLAN that act as a central transmitter and receiver of WLAN radio signals.
Ad Hoc Network
A short-term WLAN framework created between two or more WLAN adapters, without going
through an Access Point. An ad hoc network lets computers send data directly to and from one
another. For an ad hoc network to work, each computer on the network needs a WLAN card
installed configured for Ad Hoc mode.
Antenna
A device that sends and receives radio-frequency (RF) signals. Often camouflaged on existing
buildings, trees, water towers or other tall structures, the size and shape of antennas are generally
determined by the frequency of the signal they manage.
Authentication
A process that verifies the identity of a wireless device or end-user. A common form of
authentication is to verify identities by checking a user name and password to allow network
access.
Backbone
A high-speed line or series of connections that form a major pathway within a network.
Bandwidth
The part of the frequency spectrum required to transmit desired information. Each radio channel
has a center frequency and additional frequencies above and below this carrier frequency that
carry the transmitted information. The range of frequencies from the lowest to the highest used
is called the bandwidth.
Bridge
A wireless device that connects multiple networks that are physically separate or use different
media, but which use similar standards.
Bridge Mode
An Access Pointy in bridge mode can operate as a WLAN bridge that connects two wired network
segments. The peer device also must be in bridge mode. This wireless bridge connection is
equivalent to a Wireless Distribution System (WDS).
CHAP
Challenge Handshake Authentication Protocol. An alternative protocol that uses a
challenge/response technique instead of sending passwords over the wire.
Collision
Interference resulting from two network devices sending data at the same time. The network
detects the collision of the two transmitted packets and discards both of them.
Coverage
The region within which a paging receiver can reliably receive the transmission of paging signals.
Coverage Area
The geographical area that can be served by a mobile communications network or system.
Coverage Hole
An area within the radio coverage footprint of a wireless system where the RF signal level is
below the design threshold. Physical obstructions such as buildings, foliage, hills, tunnels, and
indoor parking garages are usually the cause of coverage holes.
Cyclic Redundancy Check (CRC)
A common technique for detecting data transmission errors.
Dynamic Host Configuration Protocol (DHCP)
A protocol that assigns temporary IP addresses automatically to client stations logging onto an IP
network, so the IP addresses do not have to be assigned manually. The OM2P V2 contains an
internal DHCP server that automatically allocates IP address using a user-defined range of IP
addresses. Dead Spot
An area within the coverage area of a WLAN where there is no coverage or transmission falling
off. Electronic interference or physical barriers such as hills, tunnels, and indoor parking garages
are usually the cause of dead spots. See also coverage area.
802.11
A category of WLAN standards defined by the Institute of Electrical and Electronics Engineers
(IEEE).
802.11a
An IEEE standard for WLANs that operate at 5 GHz, with data rates up to 54 Mbps.
802.11b
An IEEE standard for WLANs that operate at 2.4 GHz, with data rates up to 11 Mbps.
802.11g
An IEEE standard for WLANs that operates at 2.4 GHz, with data rate of 300 Mbps. The new
standard also raises the encryption bar to WPA2. The 40 HT option can be added to increase the
data rate.
Encryption
Translates data into a secret code to achieve data security. To read an encrypted file, you must
have a secret key or password for decryption. Unencrypted data is referred to as plain text;
encrypted data is referred to as cipher text
ESS ID
The unique identifier for an ESS. All Access Points and their associated wireless stations in the
same group must have the same ESSID.
Footprint
Geographical areas where an entity is licensed to broadcast its signal.
Gateway
A computer system or other device that acts as a translator between two systems that use
different communication protocols, data formatting structures, languages, and/or architecture.
HT mode
In the 802.11n system, two new formats, called High Throughput (HT), are defined for the
Physical Layer, Mixed Mode, and Green Field. If a system runs 40 HT, two adjacent 20 MHz
channels are used. The larger 40 MHz bandwidth can provide better transmit quality and speed.
Keys
Like passwords, keys open (decrypt) and close (encrypt) messages. While many encryption
algorithms are commonly known and public, the key must be kept secret.
Local-Area Network (LAN)
A small data network covering a limited area, such as a building or group of buildings. Most LANs
connect workstations or personal computers. LANs let many users share devices such as printers
as well as data. LANs also facilitate communication through e-mail or chat sessions.
Media Access Control (MAC) Address
Address associated with every hardware device on the network. Every 802.11 wireless device has
its own specific MAC address. This unique identifier is hard-coded into the device and can be
used to provide security for WLANs. When a network uses a MAC table, only the 802.11 radios
that have their MAC addresses added to that network's MAC table can access the network.
Network Address Translation (NAT)
An Internet standard that lets a LAN use one set of IP addresses for internal traffic and a second
set of addresses for external traffic.
Network Time Protocol (NTP)
A protocol that lets devices synchronize their time with a time server. NTP uses TCP or UDP port
123 by default.
Passphrase
A text string that automatically generates WEP keys on wireless client adapters.
Power Over Ethernet (PoE)
A PoE provides power to PoE-enabled devices using an 8-pin CAT 5 Ethernet cable, eliminating the
need for a power source.
Preamble
Synchronizes transmissions in a WLAN. The preamble type defines the length of the Cyclic
Redundancy Check block for communication between a device and roaming wireless stations.
Protected Extensible Authentication Protocol (PEAP)
Authentication protocol of IEEE 802.1x used to send authentication data and passwords over
802.11 WLANs.
Quality of Service (QoS)
A network’s ability to deliver data with minimum delay. QoS also refers to the networking
methods used to provide bandwidth for real-time multimedia applications.
Remote Authentication Dial-In User Service (RADIUS)
Networking protocol that provides centralized authentication, authorization, and accounting
management for computers to connect and use a network service. Because of its broad support
and ubiquitous nature, the RADIUS protocol is often used by ISPs and enterprises to manage
access to the Internet or internal networks, WLANs, and integrated e-mail services.
Service Set Identifier (SSID)
Name of a WLAN. All wireless devices on a WLAN must use the same SSID to communicate with
each other.
Simple Network Management Protocol (SNMP)
An Internet-standard protocol for managing devices on IP networks.
Snooping
Passively watching a network for data, such as passwords, that can be used to benefit a hacker.
Temporal Key Integrity Protocol (TKIP)
An encryption protocol that uses 128-bit keys. Keys are dynamically generated and distributed by
the authentication server. TKIP regularly changes and rotates encryption keys, with an encryption
key never being used twice.
Transmission Control Protocol/Internet Protocol (TCP/IP)
A protocol that allows communications over and between networks. TCP/IP is the basis for
Internet communications.
Weighted Fair Queuing (WFQ)
WFQ services queues are based on priority and queue weight. Queues with larger weights get
more service than queues with smaller weights. This highly efficient queuing mechanism divides
available bandwidth across different traffic queues.
Wired Equivalent Privacy (WEP)
Security protocol that provides a WLAN with a level of security and privacy comparable to that of
a wired LAN. WEP encrypts data sent between wired and WLANs to keep transmissions private.
Wireless Local-Area Network (WLAN)
WLANs use RF technology to send and receive data wirelessly in a certain area. This lets users in a
small zone send data and share resources such as printers without using cables to physically
connect each computer.
Wi-Fi Protected Access (WPA )
A subset of the IEEE 802.11i standard. WPA applies IEEE 802.1x and Extensible Authentication
Protocol (EAP) to authenticate wireless clients using an external RADIUS database. WPA uses
Temporal Key Integrity Protocol (TKIP), Message Integrity Check (MIC), and IEEE 802.1x to encrypt
data. See also WPA-PSK (WPA -Pre-Shared Key).
Wi-Fi MultiMedia (WMM)
Part of the IEEE 802.11e QoS enhancement to the Wi-Fi standard that ensures quality of service
for multimedia applications in WLANs.
Wireless Client Supplicants
Software that runs on an operating system, instructing the wireless client how to use WPA.
WPA -Pre-Shared Key (WPA-PSK)
WPA-PSK requires a single (identical) password entered into each Access Point, wireless gateway,
and wireless client. A client is granted access to a WLAN if the passwords match.
WPA2
A wireless security standard that defines stronger encryption, authentication, and key
management than WPA. It includes two data encryption algorithms, Temporal Key Integrity
Protocol (TKIP) and Advanced Encryption Standard (AES) in the Counter mode with Cipher block
chaining Message authentication Code Protocol (CCMP).
Wireless Distribution System (WDS)
A technology that lets Access Points communicate with one another to extend the range of a
WLAN.
Appendix D – FCC Interference Statement
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Copyright © 2011 ENGENIUS TECHNOLOGIES, INC., All rights reserved.
Europe – EU Declaration of
o Conformity
This device complies with the essential requirements of the R&TTE Directive
1999/5/EC. The following test methods have been applied in order to prove
presumption of conformity with the essential requirements of the R&TTE Directive
1999/5/EC:
EN60950-1
Safety of Information Technology Equipment
EN50385
Generic standard to demonstrate the compliance of electronic and electrical
apparatus with the basic restrictions related to human exposure to electromagnetic
fields (0 Hz - 300 GHz)
EN 300 328
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband
Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM
band and using spread spectrum modulation techniques; Harmonized EN covering
essential requirements under article 3.2 of the R&TTE Directive
EN 301 489-1
Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic
Compatibility (EMC) standard for radio equipment and services; Part 1: Common
technical requirements
EN 301 489-17
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic
Compatibility (EMC) standard for radio equipment and services; Part 17: Specific
conditions for 2,4 GHz wideband transmission systems and 5 GHz high
performance RLAN equipment
0560
Česky
[Czech]
[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími
příslušnými ustanoveními směrnice 1999/5/ES.
Dansk
[Danish]
Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse]
overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch
[German]
Hiermit erklärt [Name des Herstellers],
Herstellers] dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den
grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG
befindet.
Eesti
[Estonian]
English
Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment]
vastavust direktiivi 1999/5/EÜ
1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele
sätetele.
Hereby, [name of manufacturer],
manufacturer] declares that this [type of equipment] is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los
requisitos esenciales y cualesquiera
cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ
ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
1999/
Français
[French]
Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences
essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Italiano
[Italian]
Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti
essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski
[Latvian]
pe of equipment / iekārtas tips]
Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type
atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių
[Lithuanian]
Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas
1999/5/EB Direktyvos nuostatas.
Nederlands
[Dutch]
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de
essentiële eisen en de andere relevante bepalingen van richtlijn
richtlijn 1999/5/EG.
Malti
[Maltese]
Hawnhekk, [isem tal-m
manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ħtiġijiet
mal
essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva
fid Dirrettiva 1999/5/EC.
Magyar
[Hungarian]
Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ követelményeknek
és az 1999/5/EC irányelv egyéb elõírásainak.
elõírásainak
Polski
[Polish]
Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami
oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português
[Portuguese]
[Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais
e outras disposições da Directiva
Di
1999/5/CE.
Slovensko
[Slovenian]
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi
določili direktive 1999/5/ES.
Slovensky
[Slovak]
[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a všetky príslušné
ustanovenia Smernice 1999/5/ES.
Suomi
[Finnish]
[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä]
tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja
ja sitä koskevien direktiivin muiden
ehtojen mukainen.
Svenska
[Swedish]
Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga
egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux
appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions
suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce
dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Annotate, Fill forms
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : GPL Ghostscript  9.0
Keywords                        : 
Modify Date                     : 2014:02:24 15:23:12+08:00
Create Date                     : 2014:02:24 15:19:17+08:00
Creator Tool                    : PDFCreator Version 1.2.0
Metadata Date                   : 2014:02:24 15:23:12+08:00
Document ID                     : 874b6c67-9f7f-11e3-0000-e6240da3d0ad
Instance ID                     : uuid:7ccbbd3f-03e8-4cfe-bbe3-e75185cafde0
Format                          : application/pdf
Title                           : OM2P v2_UM_for FCC & CE & IC apply_v2
Creator                         : aihsu
Description                     : ()
Page Count                      : 96
Subject                         : 
Author                          : aihsu

EXIF Metadata provided by EXIF.tools

Datto OM2PV2 Wireless 802.11b/g/n Mesh Router User Manual OM2P v2 UM for FCC CE IC apply v2

Open Mesh, Inc. Wireless 802.11b/g/n Mesh Router OM2P v2 UM for FCC CE IC apply v2

User Manual_rev.pdf

FCC ID Filing: WT8-OM2PV2

Navigation menu

Namespaces

Views

Navigation