Deere and John Deere Intelligent Solutions Group PF80452 JDLINK Machine Messenger User Manual 102128UNIT

Deere & Company dba John Deere Intelligent Solutions Group JDLINK Machine Messenger 102128UNIT

manual

JDLINKMachineMessengerINSTALLATION INSTRUCTIONSJDLINK Machine MessengerPC20103 09JAN02 (ENGLISH)8020, 9020John Deere Ag Management SolutionsPC20103 (09JAN02)COPYRIGHT 2001DEERE & COMPANYMoline, IllinoisAll rights reservedA John Deere ILLUSTRUCTIONManualPC20103-19-09JAN02P R O O F P R O O F
Installation InstructionsDX,ALERT –19–29SEP98–1/1Recognize Safety InformationT81389 –UN–07DEC88This is a safety-alert symbol. When you see this symbolon your machine or in this manual, be alert to thepotential for personal injury.Follow recommended precautions and safe operatingpractices.OUO6091,0001435 –19–20AUG01–1/1JDLINK Wiring Harness ReferencePC6783 –UN–19DEC01PC6782 –UN–19DEC01A—Socket Connector To ControllerB—CAN Bus Terminator ConnectorC—Ground wireD—CCD Bus ConnectorE—CAN Bus Terminator ConnectorF—Unswitched And Switch Power WiresG—SCV Panel ConnectorH—10 Amp Fuses(09JAN02)1Installation Instructions010902PN=3P R O O F P R O O F
Installation InstructionsOUO6091,0001433 –19–14AUG01–1/27Install JDLINKMachine MessengerIMPORTANT: Avoid damage to electrical system oftractor when installing JDLINK wiringharness. Disconnect battery ground.NOTE: After installing JDLINK Machine Messenger andbefore reassembling cab roof, login to JDLINKwebsite at www.jdlink.com, go to DealerMenu/Setup New Device wizard and follow onlineprocedures. These procedures will allow JDLINKcommunication controller’s serial number to beverified and tractor’s serial number to be enteredfor proper system operation.Reference of JDLINK Machine Messenger’sTechnical Manual is required for this instruction.1. Shut off engine, set parking brake and remove key.JDLINK is a trademark of Deere & CompanyContinued on next page(09JAN02)2Installation Instructions010902PN=4P R O O F P R O O F
Installation InstructionsOUO6091,0001433 –19–14AUG01–2/27PC6928 –UN–28NOV01PC6929 –UN–28NOV01PC6931 –UN–29NOV01PC6930 –UN–28NOV01A—TORX ScrewsB—Plastic RivetsC—Cap ScrewD—ScrewsE—Console CoverNOTE: If tractor is equipped with JDLINK wiring harnessgo to step 11.2. Remove TORXscrews (A).3. Remove plastic rivets (B).4. Remove cap screw (C).NOTE: To access console screws (D), remove fuse panelcover.5. Remove screws (D) and console cover (E).TORX is a trademark of Camcar/Textron(09JAN02)3Installation Instructions010902PN=5P R O O F P R O O FContinued on next page
Installation InstructionsOUO6091,0001433 –19–14AUG01–3/27PC6764 –UN–14AUG01A—Shroud ScrewsB—Post Shroud6. Remove right rear shroud screws (A) and shroud (B).OUO6091,0001433 –19–14AUG01–4/27PC6934 –UN–28NOV01A—ScrewB—LightC—Trim ScrewsD—TrimNOTE: Remove headliner enough to route wiring harnessdown right-rear corner post.7. Remove screw (A), light (B), trim screws (C) andheadliner trim (D).OUO6091,0001433 –19–14AUG01–5/27PC6933 –UN–28NOV01A—Rear Window Molding8. Remove right rear window molding (A).OUO6091,0001433 –19–14AUG01–6/27PC6766 –UN–28NOV01A—ScrewB—Panel SpacerC—SCV Panel9. Remove screw (A), panel spacer (B) and SCV setuppanel (C).(09JAN02)4Installation Instructions010902PN=6P R O O F P R O O FContinued on next page
Installation InstructionsOUO6091,0001433 –19–14AUG01–7/27PC6767 –UN–19DEC01A—CAN Bus TerminatorNOTE: CAN bus terminator will be reinstalled on roof ofcab in a following step.10. Disconnect and remove CAN bus terminator (A).OUO6091,0001433 –19–14AUG01–8/27PC6762 –UN–14AUG01A—Cap ScrewsB—Mirror11. Remove flange cap screws (A) and mirror (B).12. Disconnect and remove STARFIREreceiver, ifequipped.NOTE: Refer to machine Technical Manual for removal ofrear cab lights and radio antenna.13. Remove rear cab lights and disconnect radio antenna.STARFIRE is a trademark of Deere & CompanyOUO6091,0001433 –19–14AUG01–9/27PC6763 –UN–14AUG01A—Cap Screws (16 used)B—Cap Screws (2 used)C—Cab RoofNOTE: Cab roof is awkward to handle, use suitable liftingdevice or two technicians.14. Remove cap screws (A and B), washers and cabroof (C).Continued on next page(09JAN02)5Installation Instructions010902PN=7P R O O F P R O O F
Installation InstructionsOUO6091,0001433 –19–14AUG01–10/27PC6781 –UN–20AUG01PC6771 –UN–20AUG01A—CoaxB—CoaxC—Antenna AssemblyD—Cap Screws15. Connect coax cables (A and B) to antenna assembly(C).IMPORTANT: Improperly installed antenna andreceiver may interfere with theoperation of machine’s electronicsystem and possibly subject operator tohigher than recommended radiofrequency emission levels.16. Attach antenna assembly to right rear-window hingeusing existing cap screws (D).OUO6091,0001433 –19–14AUG01–11/27PC6938 –UN–29NOV01Reference Of 8020A—Coax CableB—Antenna AssemblyC—ControllerNOTE: For all machines, route coax cables on right sideof cab.17. Route coax cables (A) on right side of tractor cabfrom antenna assembly (B) to controller (C).Continued on next page(09JAN02)6Installation Instructions010902PN=8P R O O F P R O O F
Installation InstructionsOUO6091,0001433 –19–14AUG01–12/27PC6768 –UN–14AUG01PC6769 –UN–16AUG01PC6760 –UN–10AUG01Template (Reference Only)A—TemplateB—Hole GuidesNOTE: Use pullout templates (included with thisinstruction) to locate and drill holes at left frontsection of cab. Templates below are for referenceonly. If tractor is equipped with JDLINK wiringharness, skip to step 21.18. Install templates (A) and tape corners of templates tobrackets. Locate and mark four holes (B) for drilling.19. Remove templates.20. Drill four 8 mm (5/16 in) holes (B).(09JAN02)7Installation Instructions010902PN=9P R O O F P R O O FContinued on next page
Installation InstructionsOUO6091,0001433 –19–14AUG01–13/27PC6773 –UN–28NOV0121. Attach coax cables (A) to controller (B).22. Connect JDLINK wiring harness connector (C) tocontroller and tighten cap screw (D).NOTE: Record controller’s 13 digit serial number for afollowing step.23. Install terminator (E) and retain with tie straps.OUO6091,0001433 –19–14AUG01–14/27PC6780 –UN–28NOV01A—ControllerB—Cap Screws (4 used)C—Ground WireD—Nut24. Attach controller (A), using four 6 mm cap screws (B).25. Attach ground wire from JDLINK wiring harness (C) tocontroller using existing nut (D).Continued on next page(09JAN02)8Installation Instructions010902PN=10P R O O F P R O O F
Installation InstructionsOUO6091,0001433 –19–14AUG01–15/27BACDPC6761 –UN–15AUG01Ground Wire Route For 8020 Wheel And 9020 TrackPC6966 –UN–18DEC01Ground Wire Route for 9020 WheelPC6774 –UN–14AUG01Chassis Ground for 8020A—JDLINK ControllerB—JDLINK Antenna AssemblyC—Ground WireD—JDLINK Wiring HarnessE—Chassis PostNOTE: Record machine’s 13 digit serial number for afollowing step.If equipped with JDLINK wiring harness skip tostep 32.Place controller ground wire next to chassisbehind second nut.26. Route ground wire (C) along side of windshieldwasher hose and connect to chassis ground (E).Continued on next page(09JAN02)9Installation Instructions010902PN=11P R O O F P R O O F
Installation InstructionsOUO6091,0001433 –19–14AUG01–16/27PC6775 –UN–14AUG01PC6939 –UN–28NOV01A—JDLINK Wiring HarnessB—Cab SlotIMPORTANT: Avoid damage to antenna coax cablesand JDLINK wiring harness whenreinstalling cab roof. Tie strap wiringharness and coax cables in areas ontop of cab to prevent damage of wiresand cables (tie strap cables and wiringharness together from right rear cabslot to controller).27. Route JDLINK wiring harness (A) to SCV panelthrough slot (B) at right rear cab post.OUO6091,0001433 –19–14AUG01–17/27PC6971 –UN–20DEC01A—JDLINK Connector And CAN Bus TerminatorConnector28. Connect JDLINK connector to CAN bus terminatorconnector (A).OUO6091,0001433 –19–14AUG01–18/27PC6777 –UN–14AUG01A—Unswitch Power Wire, 262B—PostC—Switch Power Wire, 192D—Power Post29. Connect JDLINK unswitch power wire (A) to post (B)and power switch wire (C) to post (D) with hardwareprovided.(09JAN02)10Installation Instructions010902PN=12P R O O F P R O O FContinued on next page
Installation InstructionsOUO6091,0001433 –19–14AUG01–19/27PC6778 –UN–14AUG01A—JDLINK SCV ConnectorB—SCV Panel Wiring Harness ConnectorNOTE: Reference JDLINK wiring harness at beginning ofinstruction for CCD Bus connector.30. Connect JDLINK SCV connector (B) to SCV panelwiring harness connector (A).Continued on next page(09JAN02)11Installation Instructions010902PN=13P R O O F P R O O F
Installation InstructionsOUO6091,0001433 –19–14AUG01–20/27PC6969 –UN–19DEC01A—CCD Bus ConnectorB—SCV Panel31. Connect JDLINK wiring harness CCD Bus connector(A) to SCV panel (B).32. Reconnect battery ground.IMPORTANT: Avoid damage to machine, reinstallmachine enough to be moved but donot fully reassemble until properoperation of JDLINK is confirmed.33. To properly confirm operation of JDLINK, movemachine to an open area so it has clear view of skyhorizon.34. Shut off engine , set parking brake.35. Reference JDLINK Machine Messenger’s TechnicalManual to force a contact from the machine toconfirm cell service.NOTE: Machine must be turned to the RUN position forfive minutes before step 6 of 8 in the online SetupConfirmation procedure of the machine andcontroller.36. Login to JDLINK website, go to Dealer Menu/SetupNew Device Wizard and follow online procedures,which will include the input of machine andcontroller’s serial number.37. Confirm test data (i.e. time/date, map location,machine’s engine hours and electronics systeminformation).If data is correct reassemble machine, if data isincorrect call 1-888-GRNSTAR.38. Shut off engine, set parking brake and remove key.Continued on next page(09JAN02)12Installation Instructions010902PN=14P R O O F P R O O F
Installation InstructionsOUO6091,0001433 –19–14AUG01–21/27PC6766 –UN–28NOV01A—ScrewB—SCV Panel SpacerC—SCV PanelNOTE: If equipped with JDLINK wiring harness skip tostep 47.39. Reinstall SCV panel (C), panel spacer (B) and retainwith screw (A).Continued on next page(09JAN02)13Installation Instructions010902PN=15P R O O F P R O O F
Installation InstructionsOUO6091,0001433 –19–14AUG01–22/27PC6930 –UN–28NOV01PC6931 –UN–29NOV01PC6929 –UN–28NOV01PC6928 –UN–28NOV01A—TORX ScrewsB—RivetsC—Cap ScrewD—ScrewsE—ConsoleNOTE: After reinstallation of console, reinstall fuse panelcover.40. Reinstall console (E) and screws (D).41. Reinstall cap screw (C) and new rivets (B).42. Reinstall TORX screws (A).(09JAN02)14Installation Instructions010902PN=16P R O O F P R O O FContinued on next page
Installation InstructionsOUO6091,0001433 –19–14AUG01–23/27PC6933 –UN–28NOV01A—Rear Window Molding43. Reinstall rear window molding (A).OUO6091,0001433 –19–14AUG01–24/27PC6934 –UN–28NOV01A—ScrewB—LightC—TrimD—Trim Screws44. Reinstall headliner trim (D) retain with screws (C).45. Reinstall light (B) and retain with screw (A).OUO6091,0001433 –19–14AUG01–25/27PC6764 –UN–14AUG01A—Shroud Screws (2 used)B—Corner Post Shroud46. Reinstall right rear corner post shroud (B) retain withshroud screws (A).OUO6091,0001433 –19–14AUG01–26/27PC6763 –UN–14AUG01A—Cap Screws and Washers (16 used)B—Cap Screws and Washers (2 used)NOTE: Reinstall radio antenna coax and rear lightsbefore installing cap screws.47. Reinstall roof (C) and retain with washers and capscrews (A and B).(09JAN02)15Installation Instructions010902PN=17P R O O F P R O O FContinued on next page
Installation InstructionsOUO6091,0001433 –19–14AUG01–27/27PC6762 –UN–14AUG01A—Cap ScrewsB—Mirror48. Reinstall mirror (B) and retain with cap screws (A).49. Reinstall STARFIRE receiver, if equipped.(09JAN02)16Installation Instructions010902PN=18P R O O F P R O O F

Navigation menu