Deister Electronic AMANTAGCOMPACT Compact Reader User Manual 2007 08 08 pa amantag compact em
Deister Electronic GmbH Compact Reader 2007 08 08 pa amantag compact em
user manual
compact Wiring & Installation Instructions V04/09/07 amanTag compact © Copyright 2007 by deister electronic GmbH All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of deister electronic GmbH. deister electronic GmbH reserves the right to make changes to any and all parts of this documentation without obligation to notify any person or entity of such changes. September 2007 FS/BF deister electronic GmbH Hermann-Bahlsen Str. 11 30890 Barsinghausen Germany Phone: +49 (0) 51 05 - 51 61 11 Fax: +49 (0) 51 05 - 51 62 17 E-Mail: info@deister-gmbh.de Web: www.deister.com deister electronic GmbH 30890 Barsinghausen Germany V04/09/07 amanTag compact Content 1. General Information...................................................4 2. Technical Data.............................................................5 3. Operation....................................................................5 4. Wiring & Configuration ..............................................6 4.1 Optical display ..................................................................................................6 4.2 Pin assignment....................................................................................................7 4.3 DIP-switches.......................................................................................................9 5. Installation................................................................12 5.1 General Information..........................................................................................12 5.2 Mounting.........................................................................................................12 6. Regulatory notices.....................................................14 V04/09/07 deister electronic GmbH 30890 Barsinghausen Germany amanTag compact 1. General Information ● An amanTag compact-Reader generates an undirected field in an area up to 3 meters. In a vertical line to the reader the reading range is up to 8 meters. ● An amanTag compact-Reader is able to recognize several transponders being in the reader-field at the same time. ● The reading range can be varied gradually. ● For exchange of data a Wiegand or RS 485 Interface can be used. deister electronic GmbH 30890 Barsinghausen Germany V04/09/07 amanTag compact 2. Technical Data Meets EN(I-ETS) 300220 Dimensions (mm): 296 x 296 x 28 Transmission frequency: 8,1 kHz Receiving frequency: 433 MHz ISM-band Modulation: PSK Baud-rate in reading: 1500 Baud Sensibility: -100dBm Reading distance: up to 8 m, depending on the type of transponder Field strength in 8m distance: 99 dBμV/m average , 102 dBμV/m peak Interface: Wiegand, RS485 Voltage supply: 24V (18V...30V) 3. Operation Two different frequency ranges are used to communicate with the transponder. The activating of a transponder and data exchange to the transponder takes place within a low frequent 8,1 kHz-field. Data exchange from the transponder to the reader takes place at 433 MHz. As soon as a transponder is brought into the working range of the low frequent field, it will be activated and recognized by the reader. The transponder stays in direct contact with the reader as long as it is located in the working range of the low frequent field. V04/09/07 deister electronic GmbH 30890 Barsinghausen Germany amanTag compact 4. Wiring & Configuration 4.1 Optical display An amanTag compact is equipped with three LEDs for optical display. The functions assigned are as follows: LED yellow: “Power ON”-display. Turned on constantly when connected to the power supply. LED green: Tag received. Blinks in case a transponder telegram has been received. LED red: Tag in field. Is active as long as a transponder is located in the field. yellow green red Board of the reader deister electronic GmbH 30890 Barsinghausen Germany V04/09/07 amanTag compact 4.2 Pin assignment A schematic description of the position of the pins and dip-switches is given in the diagram below: yellow green red ST1 ST2 ST3 ST4 ST5 Bank A Bank B DIP-Switches In the lower part of the card there are five connector rails for connecting to the power supply and to other devices in the peripheral equipment. The connector rails are assigned as follows. ST1 ST2 V04/09/07 9 10 11 12 ST3 ST4 ST5 deister electronic GmbH 30890 Barsinghausen Germany amanTag compact ST1 (PRX) P1 beeper–input P2 ground P3 positive currant voltage 24V (18V – 30V) P4 Wiegand-output D1 ( loading arrangement RS 232 ) P5 Wiegand-output D0 P6 Wiegand-output CP P7 LED green input P8 LED red input P9 RS485 - A P10 RS485 - B P11 Tamper-contact P12 Tamper-contact ST2 (SATELLITE) P1 positive currant voltage, 24V (18V ... 30V) P2 ground P3 RS485 - A P4 RS485 – B ST3 (SYNC) P1 positive currant voltage, 24V (18V ... 30V) P2 ground P3 SYNC - A P4 SYNC – B P5 SYNC-AIN P6 SYNC-BIN ST4 (RELAYS 1) P1 connected to P2, in case yellow LED is turned off (Breakdown of current voltage or alarm-condition) P2 reference connection of the relays P3 connected to P2, in case the yellow LED is turned on ST5 (RELAYS 2) P1 connected to P2, in case the red LED is turned off P2 reference connection of the relays P3 connected to P2, in case the red LED is turned on (alarm-condition) deister electronic GmbH 30890 Barsinghausen Germany V04/09/07 amanTag compact 4.3 DIP-switches The amanTag compact can be configured with two eight pole dip-switches (rail A and B). ON ON # # # # # A1 A2 A3 A4 A5 A6 A7 A8 B1 B2 B3 # # # # # B4 B5 B6 B7 B8 A1 activate the monitor tag function. A2 always has to be „on“. A3 reserved for testing-modes, has to be turned off! A4 in case this switch is set, the RS485-address is defined by the door-number A5-A8 Binary switch-group for definition of the door number The numbers 0000 and 1000 must not be used! B1-B4 binary switch-group to determine the wake-up-range B5 reserved for testing-modes, has to be turned off! B6 special function for ending the transport mode of the transponders. Should be turned off during normal working mode. B7 reserved for testing-modes, has to be turned off! B8 has to be set, to activate the RS485-receiver. V04/09/07 deister electronic GmbH 30890 Barsinghausen Germany amanTag compact Examples for adjusting the door-number: Door-number 1: ON A1 A2 A3 A4 A5 A6 A7 A8 Door-number 2: ON A1 A2 A3 A4 A5 A6 A7 A8 Door-number 3: ON A1 A2 A3 A4 A5 A6 A7 A8 Door-number 8: (reserved, should not be used) ON A1 10 A2 A3 A4 A5 A6 A7 A8 deister electronic GmbH 30890 Barsinghausen Germany V04/09/07 amanTag compact Examples for adjusting the wake-up-range: Range 1: ON B1 B2 B3 B4 B5 B6 B7 B8 Range 2: ON B1 B2 B3 B4 B5 B6 B7 B8 Range 3: ON B1 B2 B3 B4 B5 B6 B7 B8 B5 B7 B8 Range 8: ON B1 B2 V04/09/07 B3 B4 B6 deister electronic GmbH 30890 Barsinghausen Germany 11 amanTag compact 5. Installation 5.1 General Information ● During the installation it is important to take care that the readers are not too close together. The low frequent fields of the readers must not overlap. ● The wake-up-fields of the different readers must not overlap. The range of the field can be varied by the dip-switches B1-B4. ● Mounting on a metallic surface or on brick-walls with lots of steel reinforcement can reduce (or unexpectedly extend) the wake-up-range of the reader. 5.2 Mounting The amanTag compact reader will be mounted to the wall with 4 screws. The back panel of the device is provided with the according drill holes for the screws and the wire outlets. The dimensions can be seen in the following diagrams. 12 deister electronic GmbH 30890 Barsinghausen Germany V04/09/07 amanTag compact V04/09/07 deister electronic GmbH 30890 Barsinghausen Germany 13 amanTag compact 6. Regulatory notices Hereby, deister electronic GmbH declares that this equipment - if used according to the instructions - is in compliance with the essential requirements and other relevant provisions of the RTTE Directive 1999/5/ EC. A full declaration of conformity can be requested at: info@deister-gmbh.de Approved for use in all European countries. FCC Digital Device Limitations Radio and Television Interference This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAUTION: Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment. Industry Canada This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 14 deister electronic GmbH 30890 Barsinghausen Germany V04/09/07 amanTag compact Notes: V04/09/07 deister electronic GmbH 30890 Barsinghausen Germany 15 deister worldwide Germany: deister electronic GmbH Hermann-Bahlsen Str. 11 30890 Barsinghausen Tel.: +49 (0) 51 05 - 51 61 11 Fax: +49 (0) 51 05 - 51 62 17 info@deister-gmbh.de www.deister.com France: deister electronic france 101 rue Pierre Semard 92320 Chatillon Tel.: +33 (0) 1 47 - 35 78 78 Fax: +33 (0) 1 47 - 35 92 59 info.fr@deister.com Great Britain: deister electronic (UK) Ltd. Stapleton Way, Enterprise Park Spalding, Lincolnshire PE11 3YQ Tel.: +44 (0) 1775 - 717100 Fax: +44 (0) 1775 - 717101 info.uk@deister.com Japan: deister electronic Japan, LTD. Toshiba Hoshikawa Bldg. 4F 2-4 Kawabe-chô Hodogaya-ku, Yokohama-shi Kanagawa, 240-0001 Tel.: +81 (0) 45 340 1831 Fax: +81 (0) 45 340 1801 info.jp@deister.com Americas and Caribbean: Deister Electronics USA, Inc. 9303 Grant Avenue Manassas, VA 20110 Tel.: +1 703 - 368 2739 Fax: +1 703 - 368 9791 info.us@deister.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Print high-res Author : Björn Create Date : 2011:11:23 11:30:30+01:00 Modify Date : 2011:11:23 11:30:30+01:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Creator Tool : PScript5.dll Version 5.2.2 Format : application/pdf Title : 2007_08_08_pa_amantag_compact_em Creator : Björn Producer : Acrobat Distiller 9.4.6 (Windows) Document ID : uuid:318ee53e-be94-466e-9d98-00d86a23cacd Instance ID : uuid:c03a9991-f479-4591-8a96-37482574be92 Page Count : 16EXIF Metadata provided by EXIF.tools