Deister Electronic TSU200 RFID Reader User Manual
Deister Electronic GmbH RFID Reader
user manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2184069 |
| Application ID | ERuJPR7ajMDkl+hY7pvr4w== |
| Document Description | user manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 118.46kB (1480715 bits) |
| Date Submitted | 2014-02-06 00:00:00 |
| Date Available | 2014-02-06 00:00:00 |
| Creation Date | 2014-02-05 13:18:29 |
| Producing Software | LibreOffice 4.0 |
| Document Lastmod | 0000-00-00 00:00:00 |
| Document Title | user manual |
| Document Creator | Writer |
| Document Author: | Björn Fischer |
TSU 200 Long Distance Reader Wiring and Installation Instructions Art. # 896215 Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf Regulatory Notices Europe Hereby, deister electronic GmbH declares that this equipment - if used according to the instructions - is in compliance with the essential requirements and other relevant provisions of the RTTE Directive 1999/5/EC. A full declaration of conformity can be requested at: info@deister-gmbh.de Approved for use in all European countries. FCC Digital Device Limitations Radio and Television Interference This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harm ful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and television reception. Caution! Changes or modifications not expressly approved by the manufacturer could void the user´s authority to operate this equipment. FCC Notice To comply with FCC Part 15 rules in the United States, the system must be professionally installed to ensure compliance with the Part 15 certification. It is the responsibility of the operator and professional installer to ensure that only certified systems are deployed in the United States. The use of the system in any other combination (such as co-located antennas transmitting the same information) is expressly forbidden. FCC Radiation Exposure Statement This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and the human body. Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf Industry Canada This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. © Copyright 2014 by deister electronic GmbH Disclaimer deister electronic GmbH is not able to supervise the observance of the instructions given in this manual as well as the conditions and methods used during installation, operation and maintenance of the electronic devices and components respectively. Therefore we disclaim liability and reject responsibility for any losses, damages or costs that are caused by misapplication, installation, handling errors or faulty operation or related to the above in any other way. All our products are subject to current advancement, therefore we reserve the right for modifications without prior notice. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of deister electronic GmbH. deister electronic GmbH reserves the right to make changes to any and all parts of this documentation without obligation to notify any person or entity of such changes. deister electronic GmbH Hermann-Bahlsen Str. 11 30890 Barsinghausen Germany Phone:+49 (0) 51 05 - 51 61 11 Fax: +49 (0) 51 05 - 51 62 17 E-Mail: info.de@deister.com Web: www.deister.com Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf Content 1. Technical Data............................................................5 2. Mechanical Dimensions..............................................6 2.1 Side View...........................................................................................................6 2.2 Front View..........................................................................................................6 2.3 Rear View...........................................................................................................7 3. Wiring.........................................................................7 3.1 Installation Notes................................................................................................7 3.2 Pin Assignment...................................................................................................8 4. LEDs and Beeper.........................................................9 5. Mounting...................................................................10 5.1 Mounting on poles and pipes.............................................................................10 5.1.1 Mounting the base plate for mast mounting LRM3.......................................10 5.2 Montage on walls and ceilings...........................................................................11 5.2.1 Mounting with ball joint bracket LRM1........................................................11 5.2.2 Direct Mounting.......................................................................................11 5.3 Function Principle and Environmental Influences...................................................12 6. Installation Notes......................................................13 6.1 Installation on the side of the road:.....................................................................13 6.2 Installation above the road.................................................................................13 6.3 Reading Distance .............................................................................................14 7. Test Mode..................................................................15 8. Configuration of WebConfig Software .....................16 8.1 Preparations.....................................................................................................16 8.2 SNG 3 Interface Converter.................................................................................16 8.3 Starting WebConfig...........................................................................................17 8.3.1 Summary ................................................................................................18 8.3.2 Basic Setup..............................................................................................19 8.3.3 Frequency Setup......................................................................................20 8.3.4 Frequencies.............................................................................................20 9. Accessories................................................................23 Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 1. Technical Data Dimensions: mm (inch) W x H x D 200 x 175 x 60 (7.87 x 6.89 x 2.36) Weight kg (lbs) 1.2 (2.6) Housing Material: ABS/PC, Al (powder-coated) Protection Class: IP67 Operating Temperature: °C (°F) -20 ... 50 (-4 ... 122) Relative Humidity: 5...95, non-condensing Power Requierement: 12...28 +20 % VDC / max. 1 A Frequencies: MHz 865 – 868 (EU) 902 – 928 (US) Transmit Power: E.R.P. max. 1 W (configurable) Antennas with Beam width/Polarization: 90° circular Transponder Protocols: ISO18000-6 C (EPC Class1 Gen2) Reading Distance: m (ft.) up to 7 (23) Writing Distance: m (ft.) up to 50% of reading distance, depending on transponder, antenna configuration and environmental conditions Interface: RS485 (deBus Protokoll) Electrical Connection: M12-Connector with 4 Pins Conformity: EN 50346 EN 301489 EN 302208 (DRM) Air Interface (EU) Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 2. Mechanical Dimensions All Dimensions in mm (inch) 2.1 Side View 2.2 Front View Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 2.3 Rear View Attention! M6 Allen screws only! 3. Wiring 3.1 Installation Notes 1) Installing the earth terminal: 1. 2. The earth terminal is supplied with the unit and can be installed at the prepared location when needed, for example when the unit is installed outdoors. Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 2) Attention: When installing the reader, make sure the tab connector (as shown) is professionally grounded with a flexible line with at least 0.75 mm² (0.11 inch²) (18 gauge) cross section. Connect the earth cable here after installing the earth terminal provided. 3.2 Pin Assignment The TSU 200 has an M12 connector (male) with 4 pins. Pin assignment is as follows: PIN Description +Vcc RS485-A GND RS485-B Because of the line resistance, certain cable lengths should not be exceeded. The data wires 485-A and 485-B should be twisted together, particularly when using long cables (twisted pair cable). See examples on next page. Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf Examples: Power Supply Voltage Wire Diameter Maximum Cable Length 12V AWG24 (0,22mm²) 5 m (16.4 ft.) 24V AWG24 (0,22mm²) 50 m (164 ft.) 12V AWG20 (0,5mm²) 10 m (32.8 ft) 24V AWG20 (0,5mm²) 100 m (328 ft.) 4. LEDs and Beeper The standard settings for the LEDs and the beeper are as follows: LED/beeper Action Visualisation Status of TSU 200 Yellow LED Short blinks (3 s off, 100 ms on) Field switched off Blinks (300 ms off, 500 ms on) Reader not interrogated Constant on Field switched on Off for short periods(200 ms off) Tag read Green LED User-defined User-defined Red LED User-defined Malfunction / user-defined Beeper User-defined User-defined = LED off / = LED on Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 5. Mounting 5.1 Mounting on poles and pipes For installation on a mast or tube, the baseplate LRM3 (included in scope of supply, see Section 5.1.1) must be mounted on the rear of the TSU 200, so that it can be adjusted vertically or horizontally. The serrated rear face of the LRM3 ensures that the reader can be securely mounted and adjusted through 360°. For greater flexibility of installation and adjustment of the TSU 200 on masts or tubes, we recommend use of the ball-joint mounting LRM1 (optional, see Section 5.2.1). 5.1.1 Mounting the base plate for mast mounting LRM3 Use Allen screws M6x8 ! 10 Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 5.2 Montage on walls and ceilings For mounting on walls or ceilings the ball joint bracket LRM1 (optional, see chapter 5.2.1) can be mounted directly onto the back of the reader. This mounting aid allows to adjust the reader in any desired position. Both ends of the ball joint bracket are ball-beared and connected via a rotatable axis. The desired position can be fixed with the included 3/8” Allen wrench. 5.2.1 Mounting with ball joint bracket LRM1 Use Allen screws M6x12 ! 5.2.2 Direct Mounting To mount the unit directly use the holes provided in the front face of the unit. Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 11 5.3 Function Principle and Environmental Influences The reader sends a high-frequency carrier signal. The transponder that is located within the area of this transmitted carrier transmits the signal back with its own transponder data in a modulated way. This very weak signal is being analyzed by the reader. Because of the particular small-bandwidth and the high carrier frequency this system is almost fail-safe. Nevertheless the range of the reader can be negatively influenced. The following list shows what to pay attention to: 1. The reader must have visual contact to the transponder. There must not be any walls or other devices between reader and transponder. Reading through plastic film, card board, papers or glass windows may be possible, but will reduce the reading range depending on the condition of the material. 2. Water, ice and snow will absorb the carrier signal. Therefore the installer has to make sure that the front of the reader and the transponder is not covered with water, ice or snow. 3. Reflections within the surroundings of the reader can influence the reading result in a negative way. Therefore the reader should be mounted as free-standing as possible. We strictly discourage from sunk-in installations. 4. In Multi-Reader Environment (EU only), you must assign different channels to the readers. To accomplish this, the parameter "preferred channel" should be adjusted accordingly and you have to choose the highest possible channel spacing! When using UHF readers that are installed close together (e.g. entrance and exit lane) it is recommended to pair channels such as Channel 4, 10 and channel 7, 13 etc. 12 Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 6. Installation Notes For a standard installation in a passenger-car car park, a TSU 200 can be installed either beside the roadway, or above it. 6.1 Installation on the side of the road: The reader is mounted on a pole on the driver's side next to the road at a height of 1.8 m – 2.0 m (5.9 – 6.5 ft.). Then the reader is aligned towards the transponder/car windshield. When a ground loop is present, it should be used to trigger the reader. The distance from the reader to the ground loop should be in the range of 2.0 m - 2.5 m (6.5 – 8.2 ft.). 6.5 ft. – 8.2 ft. 5.9 ft. – 6.5 ft. Ground Loop 6.2 Installation above the road The reader should not be installed higher than 3.0 m (9.8 ft.) above the road. The distance from the reader to the groundloop should be in the range of 1.5 m - 2.5 m (4.9 – 8.2 ft.). The reader is slightly tilted towards the vehicle windshield, so that the reader is almost vertically aligned with the windshield. 4.9 ft. – 8.2 ft. max. 9.8 ft. Ground Loop Note: The antenna beam of the reader shall in no case be restricted by objects above or below the reader. Flush mounting is not recommended! If other types of vehicles (trucks, small cars etc) need to be identified, the reader must be installed and aligned individually. Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 13 6.3 Reading Distance Given the condition that the transponder is aligned towards the reader, a detection range as shown in the figure below is the result when the reader is operated detached. The reading range varies due to environmental influences. For example, reflections on the ground can increase the maximum reading range. Walls, which are next to a reader, and a different transponder orientation will lead to a deformation of the reading field. It is therefore recommended to check the reading range after installation of the reader. See Chapter 7 "Test Mode". Note: The values were determined with the "TPU 3080/3090" transponder. Figure: TPU 3080 / 3090 Transponder 14 Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 7. Test Mode The TSU 200 has an integrated test mode for checking the performance of UHF transponders, and to automatically adapt the unit's antenna to local environmental conditions. This simplifies alignment of the unit and its adaptation to specific local circumstances of the application. The test mode can be activated with the test transponder TPU 3080T (Art. No. 1388.000) within 30 seconds after the unit is switched on. After activation the antenna is first automatically adjusted. During this adjustment there must not be any object directly in front of the antenna. Following this, for a period of five minutes, each transponder in the field will be signalled by the three LEDs and the beeper. Using the deister test transponder, the specified reading distance in an installed system can be checked at any time. Notification Status TSU 200 Yellow LED on for 30 seconds after switching on Waiting for test transponder Red, green, yellow LED light sequence Test mode All LEDs blink, beeper Transponder read in test mode Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 15 8. Configuration of WebConfig Software 8.1 Preparations A virtual serial COM port is set up via the USB port. The driver installation is described in the manual of the SNG 3. 8.2 SNG 3 Interface Converter The interface converter SNG3 (optional, see 9. “Accessories”) can be used for connecting a reader to a host/PC via USB. Powering of the reader is carried out by the SNG3 as long as it is connected to a power supply unit itself. To do so, a special wall power supply is available (optional, also see 9. “Accessories”). The drivers needed can be found on the CD within delivery. SNG 3 Description Function TSU 200 Pin 1 +VCC supply voltage for TSU 200 (12...24 V/DC) Pin 1 Pin 2 GND ground Pin 3 Pin 3 RS485 - A RS485 interface, data line A Pin 2 Pin 4 RS485 - B RS485 interface, data line B Pin 4 Connect as follows: Power Supply 16 Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 8.3 Starting WebConfig After the successful installation of the virtual COM port driver, run the WebConfig software. Copy the file "WebConfig.exe" from the supplied CD into a suitable directory on your local hard disk and open it by double-clicking. The configuration of the "TSU 200" must be carried out as follows: Step Configuration Software “WebConfig.” Reader TSU 200 connect reader to SNG3 (see table page 16), connect SNG3 to PC via USB cable, connect wall power supply to SNG3 Start configuration software “WebConfig” Select USB Serial Port Click on „Device“ – „Search addresses“ Software searches for the reader which is connected to the selected COM Port After successful search the reader found will be indicated Current reader configuration will be read Configuration menu will open Configuration can be modified by user 10 Transfer changed configuration to the reader by clicking on “Apply Changes” 11 Reader will store the new configuration within its internal nonvolatile memory 12 End connection by clicking on “Offline” 13 Program will be closed by „File“ - „Exit“ Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 17 8.3.1 Summary This menu shows a summary of the current reader configuration. Device Info Serial number: Device: Version: Region: Hardware configuration: Serial number of device Identification code of device Firmware version (SW) and hardware version (HW) of device Region the device is authorized for Hardware configuration code of device Note: The picture shows the frequency settings for a European unit. In countries such as e.g. the United States the frequency setup may vary. See Fehler: Referenz nicht gefunden “Fehler: Referenz nicht gefunden“. 18 Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 8.3.2 Basic Setup Enable RS485 termination If this check box is selected, the internal RS485 termination of the reader is switched on. This function is permanently activated in the TSU 200! read mode This parameter defines, if the reader expects only one tag in the antenna field or if there may be more tags within the antenna field. In case there are more tags, the reader has to execute an anti collision algorithm. It is also possible to configure the reader to “single shot” mode in which the read signaling for the same transponder is only done once or after a timeout defined by parameter “tag timeout”. Anti collision: Operating mode in case there is more than one tag in the field single shot: Operating mode for reading tag data, in case there is only one tag in the field. The tag data will be transmitted again after the time specified in “tag timeout”. Beim TSU 200 bleibt anti collision aktiviert! tag timeout / ms (for read mode “single shot” only) This value defines the interval (timeout) in milliseconds between transmissions of a tag in "single shot" mode. After expiration of this interval it is signaled that the tag will be read again. In the TSU 200 this value remains set to 65535. RF power / dBm This value defines the radiated power of the antenna in dBm. The maximum output power of the antenna is 32 dBm. Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 19 8.3.3 Frequency Setup Preferred channel This value defines the preferred channel number before the reader uses another channel. In a multi-reader environment (EU only), use different channels for the readers. Use the “Preferred channel” parameter to make this setting. Select the greatest possible separation! Channel mask This mask defines the channels to be used by the readers. Each activated checkbox enables use of the appropriate channel (for further information, see also the section Fehler: Referenz nicht gefunden “Fehler: Referenz nicht gefunden”). Recommendation for configuration of UHF readers (EU only): If several readers are installed close together (e.g. entry and exit lanes), then channel pairs should be set up for them, for example, channels 4 and 10, and channels 7 and 13. 8.3.4 Frequencies ETSI 302 208 v1.2 Channel No. Frequency E.R.P. 865.7 MHz ≤ 2.00 W 866.3 MHz ≤ 2.00 W 10 866.9 MHz ≤ 2.00 W 13 867.5 MHz ≤ 2.00 W FCC Part 15 (US) Channel No. Frequency E.I.R.P. 902.75 MHz ≤ 4.00 W 903.25 MHz ≤ 4.00 W 903.75 MHz ≤ 4.00 W 904.25 MHz ≤ 4.00 W ... ... ... 47 925.75 MHz ≤ 4.00 W 48 926.25 MHz ≤ 4.00 W 49 926.75 MHz ≤ 4.00 W 50 927.25 MHz ≤ 4.00 W 20 Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf Korea Channel No. Frequency E.I.R.P. 917.1 MHz ≤ 4.00 W 917.7 MHz ≤ 4.00 W 918.3 MHz ≤ 4.00 W 11 918.9 MHz ≤ 4.00 W 14 919.5 MHz ≤ 4.00 W 17 920.1 MHz ≤ 4.00 W Japan Channel No. Frequency E.I.R.P. 952.4 MHz ≤ 4.00 W 952.6 MHz ≤ 4.00 W 952.8 MHz ≤ 4.00 W 953.0 MHz ≤ 4.00 W 953.2 MHz ≤ 4.00 W 953.4 MHz ≤ 4.00 W 953.6 MHz ≤ 4.00 W Singapore Channel No. Frequency E.R.P. 920.25 MHz ≤ 2.00 W 920.75 MHz ≤ 2.00 W 921.25 MHz ≤ 2.00 W 921.75 MHz ≤ 2.00 W 922.25 MHz ≤ 2.00 W 922.75 MHz ≤ 2.00 W 923.25 MHz ≤ 2.00 W 923.75 MHz ≤ 2.00 W 924.25 MHz ≤ 2.00 W 10 924.75 MHz ≤ 2.00 W Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 21 Brazil Channel No. Frequency E.R.P. 915.25 MHz ≤ 2.00 W 915.50 MHz ≤ 2.00 W 915.75 MHz ≤ 2.00 W 916.00 MHz ≤ 2.00 W ... ≤ 2.00 W 47 926.75 MHz ≤ 2.00 W 48 927.00 MHz ≤ 2.00 W 49 927.25 MHz ≤ 2.00 W 50 927.50 MHz ≤ 2.00 W China Channel No. Frequency E.R.P. 920,625 ≤ 2.00 W 920,875 ≤ 2.00 W 921,125 ≤ 2.00 W 921,375 ≤ 2.00 W 921,625 ≤ 2.00 W 921,875 ≤ 2.00 W 922,125 ≤ 2.00 W 922,375 ≤ 2.00 W 922,625 ≤ 2.00 W 10 922,875 ≤ 2.00 W 11 923,125 ≤ 2.00 W 12 923,375 ≤ 2.00 W 13 923,625 ≤ 2.00 W 14 923,875 ≤ 2.00 W 15 924,125 ≤ 2.00 W 16 924,375 ≤ 2.00 W 22 Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 9. Accessories Article Description Article No. TPU3080T Windshield test transponder. Fixcoded, protected, 01388.000 with deister logo CC2 Connection cable, grey, 3 m, M12 female connector, straight, 4-pin 09287.101 CC4 Connection cable, grey, 3 m, M12 female connector, straight, 4-pin to 4-pin Phoenix connector 09287.301 CC4 Connection cable, grey, 10 m, M12 female connector, straight, 4-pin to 4-pin Phoenix connector 06236.000 LRM1 Ball joint bracket 06103.000 LRM3 Base plate for mast mounting 06106.000 AC/DC power supply Power supply for expansion module, input voltage 08812.000 ® Euro 230 VAC, output voltage 12 VDC (1 A), Friwo plug AC/DC power supply International Power supply, input voltage 100-230 VAC, incl. 06757.000 adapter for USA/Japan and United Kingdom, output voltage 12 VDC (1.25 A), Friwo® plug AC/DC Power Supply Power supply for c-rail mounting, input voltage 90- 06756.000 260 VAC, 50-60 Hz output voltage 24 VDC (2.5 A) SNG3 Smart Network Gateway Interface converter USB-to-RS485, incl. USB interface cable, Friwo® plug (Power supply required) 08782.000 DBC deBus Converter, Interface converter for deBus components, power supply 10-30 VDC 06232.000 IDC Controller for the connection to deBus-readers power supply 10-30 VDC 06230.000 SIC1 Serial Interface Converter from RS485/deBus protocol to Open Collector/Wiegand, Dataclock, Magstripe protocol, power supply 10-30 VDC 06233.000 SIC2 Serial Interface Converter from RS485/deBus protocol to RS485/customized protocol, power supply 10-30 VDC 06234.000 SIC3 Serial Interface Converter from RS485/deBus protocol to RS232, power supply 10-30 VDC 06235.000 Zulassung_wi_en_ts_tsu-200_pro_v140205_te_bf 23 Headquarters Germany: deister electronic GmbH Hermann-Bahlsen Str. 11 30890 Barsinghausen Tel.: +49 (0) 51 05 - 51 61 11 Fax: +49 (0) 51 05 - 51 62 17 info.de@deister.com www.deister.com Benelux: deister electronic office Business Park E 19 Battelsesteenweg 455/A 2800 Mechelen Tel.: +32 (0) 15 - 28 09 68 Fax: +32 (0) 15 - 28 09 71 info.be@deister.com France: deister electronic france 101 rue Pierre Semard 92320 Chatillon Tel.: +33 (0) 1 47 - 35 78 78 Fax: +33 (0) 1 47 - 35 92 59 info.fr@deister.com Great Britain: deister electronic (UK) Ltd. Stapleton Way, Enterprise Park Spalding, Lincolnshire PE11 3YQ Tel.: +44 (0) 1775 - 717100 Fax: +44 (0) 1775 - 717101 info.uk@deister.com Japan: deister electronic Japan, LTD. Toshiba Hoshikawa Bldg. 4F 2-4 Kawabe-chô Hodogaya-ku, Yokohama-shi Kanagawa, 240-0001 Tel.: +81 (0) 45 340 1831 Fax: +81 (0) 45 340 1801 info.jp@deister.com Americas and Caribbean: Deister Electronics USA, Inc. 9303 Grant Avenue Manassas, VA 20110 Tel.: +1 703 - 368 2739 Fax: +1 703 - 368 9791 info.us@deister.com Singapore: Coselec Pte Ltd. 339158 #06-12/14 Singapore Blk 28 Kallang Place info.sg@deister.com +65 6741 5200 +65 6741 6200
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print, Print high-res Page Count : 24 Language : en-US Author : Björn Fischer Creator : Writer Producer : LibreOffice 4.0 Create Date : 2014:02:05 13:18:29+01:00EXIF Metadata provided by EXIF.tools