Diasonic Technology Co RVM-704M TOUCH SCREEN MONITOR User Manual

Diasonic Technology Co Ltd TOUCH SCREEN MONITOR

Contents

User Manual

http://www.emc2000.co.kr FCC TEST REPORT Report No.: EMC-FCC-R0079 EMC compliance Ltd. Page: 1 of 1 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval. Appendix 6. User manual
2-DIN, 7”Touchscreen MonitorModel:RVM-704MInstruction Manual (Ver 1.0)IndexIndex1. Caution2. Components of the product3. How to use the productp4. How to install the product5. Specification• Thank you for purchasing our touchscreen vehicle monitor.• Please read this manual before you use the product. • The product may be different than described in the manual; depending on renewal and/or upgrade of S/W version and performance it pg pg pcan be altered without notice.
1. Caution● For your safe operation, please read this manual before you start to use the product. We inform you that our company shall not be responsible for failures and troubles that are occurred due to misuse or neglection of the cautions written on this manual. ● Operating this equipment when driving a vehicle might cause an accident. Use the equipment after parking or stopping the vehicle in a safe area.●When wiping off the dust, use a soft fabric instead of liquid solventsWhen wiping off the dust, use a soft fabric instead of liquid solvents (thinner ,benzene etc.) solution or a wet rag.● Do not press the liquid crystal screen hard. It might be damaged by hard pressure.●Do not drop or give shock It might cause breakdown or damage●Do not drop or give shock. It might cause breakdown or damage.● Do not dismantle the product arbitrarily. We do not supply free after service for an arbitrarily dismantled product. ● Touching the power with a wet hand causes electric shock. Caution required.● For accessories or cables to connect with the product, it is recommended to use proper goods from our company. We are not responsible for any problems caused by wrong articles.● Do not disconnect the power cable during using the product. It might cause damage to the product.# Amplified explanation is as follows.● Caution: This part informs what to keep in mind or understand and what ti i i d t th d tcaution is required to use the product.● Ref (reference): Reference is about functional explanation.
2. Components of the product②①①Touch Screen③●By touching one of the small pictures during multi screen mode, the concerning small picture will be enlarged into Full Screen mode. ● By touching the screen it is possible to control the equipment or to change the settings.②Power On/Off ● Press the Power button for 0.5 seconds to turn on the screen.●Press the Power button for 0 5 seconds to turn off the screen③illuminance Sensor●Press the Power button for 0.5 seconds to turn off the screen when it is tuned on.● Behind this window a sensor detects the actual light conditions in the area around the screen. When activated via the menu settings, this sensor automatically controls the brightness of the screen. (Day/Night control)
Back side③②①①Power Cable①①Power Cable● Connect the Power Cable( VCC/GND/TRIGGER1~TRIGGER5/Speed Switch )②Camera Cable③Internal SPK●Connect theCamera Cable ( Camera cable2 )
PACKAGE CONTENTS● Please check that you have the correct contents before using this product.● If any items are missing, please contact your dealer.Monitor Sunvisor BRKTPower Cable ManualCamera CableOPTIONEXT.SPK EXT.MIC
3. How to use the productStart Screen●When the booting is ready, the multi screen as below will be displayed.When the small window isTouched, it is enlarged.Touched, it is enlarged.●When the small windows on the multi screen are touched, the channel is enlarged into full screen mode. One more touch returns it back to the multi screen mode. ●: Controls volume of the speaker●:S tti●: Settings menu● : Run the Bluetooth Phone (Optional function)● : Change Input signal● : Multi screen mode
Volume Control● Press the button to display Volume Pop-up.②③②③①①①Press the button to mute ② Press the button to increase the volume③Press the button to decrease the volume③Press the button to decrease the volume
●PthItbttth ItInput selection ●Press the Input button to change InputPress input button once: AUX1Press input button 3 times:once: AUX1button 3 times: CamPress input button twice: AUX2
●P th lti b tt t di id thMulti screen●Press the multi screen button to divide the screen.①②③④Press multi screen button once:Press multi screen button 3 times:③④button once: Cam1,Cam2times: Cam1,2,3,4①② ③④Press multi screen button twice: Cam3,Cam4
●P th tti b tt t th S ttiSetting Mode●Press the setting menu button to open the Setting screen.● CAM : Adjust brightness of Camera input screen●AUX : Adjust brightness of AUX screen●AUX Adjust brightness of AUX screen
DisplayInput the name into each channel.● Mirror : Mirror image or normal image● Up : Change up and down of the screen● Shutter : Enable to operate Shutter/Heater Camera
DisplaySetup screen position of each channel※ Caution: Cam1and AUX1 cannot be setup at the same timeCam2 and AUX2 cannot be setup at the same time.Setup the screen on each TriggerThe screen will be showed screen by each Trigger set if input Trigger.
DisplayDi l th f ll di t hDisplay the full screen according to each channel setup when setting up On Display the dividing lines of the screenDisplay the dividing lines of the screen
DisplayAdjust Parking line of each TriggerTrig 1Front & RearCalibrationTrig.1Front & RearCalibration
FunctionThe screen is turned ON automaticallyThe screen is turned ON automatically when starting the vehicleAutomatic brightness adjustment by sensor in the front housing Sensitivity of automatic brightness adjustment, level 0 to 10 controlled by actual light conditions (Day/Night)
FunctionKeep Trigger activated during setup time after Trigger off in order to bridge temporary powerloss, e.g. from vehicle’s turnlight signalRe-adjust center Point of Touch panelSTEP 1 of 3Click on center of '+' iconClick on center of + iconfor Touch screen calibration.
FunctionDetect speed of a vehicle from 10 to 200 Hz To switch automatically into the screen ON mode, by detecting a speed signal (tacho signal)
SystemSet time displaying the Menu screenSet time displayedon the screenSet time displayedon the screenThe screen is turned off when there is no input like touching it d i tti tior so during setting up time
SystemSet a password to lock the Menu buttonSupport languages for each country ( Option )
SystemInitializing set points of MenuDisplay Firmware Version and Model name
Bluetooth Phone (Optional) ● Press the button to start BluetoothScreen of Bluetooth startStart-up screen displays the Phone Book list of the phone paired: Displays call lists during absence:Di l h llli t i d: Displays phone call lists received: Displays phone call lists sent: Use for making a call dialing numbers: Displays a Phonebook list: Setup of Bluetooth : Finishes Bluetooth
Bluetooth Phone ● Enter the Paring Mode for Paring with Bluetooth by pressing the button 1. Pairing mode is set by pressing the button2. Connect Bluetooth to a cell phone you want searching Bluetooth device. (Enter the Pin code depending on type of cell phones)3. Message is displayed when it is connected as below4. Return to the start-up screen of Bluetoothby pressing the buttonby pressing the button.
Bluetooth Phone ● : Displays devices Paired * Displays devices paired up to 8 devices•Displays devices pairedpy p•Deletes devices connected by the button•Connects devices by pressing the button•Deletes all devices by pressing the button•Deletes all devices by pressing the button< Devices paired are connected automatically in order >
Bluetooth Phone ● Down load phonebook list after pairing succeed.•Call after press the number in the list.
4. InstallationPre-Installation
5. Specification- LCD : Built in 7“ TFT LCD (WVGA 800x480, with Touch Panel)- Camera : 4Ch input (1 Vp-p, 75Ω) /NTSC, PAL ( Video & Audio )-External speaker Output (( +,- 2pin ) Max 3.1V @ 8 Ohm Speaker )pppp- AUX1( RCA )- 5 Trigger inputs (Cable Input : 12 ~ 24V)- ALS Sensor (Night & Daytime Brightness detection)- Power : 12~30Vdc (12Vdc 1.3A)- Operating Temp. : -20’C ~ 55’C- Storage Temp. : -30’C ~ 85’C- Dimensions (W x H x D) : 178mm x 110mm x 44.6mm- Weight : appx. 640g

Navigation menu