Administration Guide
User Manual:
Open the PDF directly: View PDF
Page Count: 338 [warning: Documents this large are best viewed by clicking the View PDF Link!]
- PREFACE About the Administration Guide
- 1 Audit Logging
- 2 Backup and Restore HSMs and Partitions
- Backup and Restore Overview and Best Practices
- About the SafeNet Luna Backup HSM
- Backup HSM Installation, Storage, and Maintenance
- Backup and Restore From the Client to a Local Backup HSM (LunaCM)
- Backup and Restore From the Client to a Remote Backup HSM (LunaCM, RBS)
- Backup and Restore From the Appliance to a Local Backup HSM (LunaSH)
- Troubleshooting
- 3 Capabilities and Policies
- 4 Configuration File Summary
- 5 Decommissioning, Zeroizing, or Resetting an HSM to Factory Conditions
- 6 High-Availability (HA) Configuration and Operation
- High Availability (HA) Overview
- Load Balancing
- Key Replication
- Failover
- Recovery
- Performance
- Standby Members
- Planning Your Deployment
- Configuring HA
- Using HA With Your Applications
- Adding, Removing, Replacing, or Reconnecting HA Group Members
- Managing and Troubleshooting Your HA Groups
- Frequently Asked Questions
- 7 HSM Initialization
- 8 HSM Status Values
- 9 Partitions
- 10 PED Authentication
- About the Luna PED
- Using the PED
- Initial Setup
- Creating New PED Keys
- Duplicating Existing PED Keys
- Changing Your Authentication Parameters
- About Remote PED
- Remote PED Setup and Configuration
- Using Remote PED
- Relinquishing Remote PED
- Maintaining the Security of Your PED Keys
- Version Control
- Summary of PED Operations
- Troubleshooting
- The PedServer and PedClient Utilities
- The PedClient Commands
- pedclient mode assignid
- pedclient mode config
- pedclient mode deleteid
- pedclient mode releaseid
- pedclient mode setid
- pedclient mode show
- pedclient mode start
- pedclient mode stop
- pedclient mode testid
- The PedServer Commands
- pedserver appliance
- pedserver appliance deregister
- pedserver appliance list
- pedserver appliance register
- pedserver mode
- pedserver mode config
- pedserver mode connect
- pedserver mode disconnect
- pedserver mode show
- pedserver mode start
- pedserver mode stop
- pedserver regen
- 11 Performance
- 12 Security Effects of Administrative Actions
- 13 Secure Transport Mode
- 14 Secure Trusted Channel (STC)
- STC Overview
- Enabling or Disabling STC on the HSM
- Enabling or Disabling STC on a Partition
- Establishing and Configuring the STC Admin Channel on a SafeNet Luna Network ...
- Using a Hard Token to Store the STC Client Identity
- Configuring the Network and Security Settings for an STC Link
- Managing STC Tokens and Identities
- Restoring STC After HSM Zeroization
- Troubleshooting
- 15 Slot Numbering and Behavior
- 16 Software, Firmware, and Capability Upgrades
- 17 SNMP Monitoring
- 18 Tamper Events
- 19 Troubleshooting
- General Troubleshooting Tips
- System Operational and Error Messages
- Extra slots that say token not present?
- Error: 'hsm update firmware' failed. (10A0B : LUNA_RET_OPERATION_RESTRICTED) ...
- KR_ECC_POINT_INVALID Error when decrypting a file encrypted from BSAFE throug...
- Error during SSL Connect (RC_OPERATION_TIMED_OUT) logged to /var/log/messages...
- Slow/interrupted response from the HSM, and the hsm show command shows LUNA_R...
- Low Battery Message
- Keycard and Token Return Codes
- Library Codes
- Vendor-Defined Return Codes
- 20 User and Password Administration