Invotec Web Catalog

User Manual: Invotec Web Catalog

Open the PDF directly: View PDF .
Page Count: 238

Download
Open PDF In Browser	View PDF

ENT and Plastic Surgery Products Catalog

I

Care and Handling of Surgical Instruments

The methods discussed have been validated for cleaning and sterilizing medical devices
distributed by Invotec International and other fine surgical instrument suppliers. They have
been developed using standard equipment and practices common to most health care
facilities. Manual cleaning methods, steam and ETO sterilization were used as much as
possible.
The Sterilization Guidelines presented are based on type of product, placed into specific
categories.
Category
Instruments with rough surfaces
Instruments with sliding hinges
Instruments with screw pivot hinges
Instruments whose surfaces that can be
marred, scored, or scratched.
Instruments with lumens and channels

Type of Product
Applicators, burs, rasps, brushes, curettes
Adenotomes, forceps, punches, rongeur
Scissors, specula, retractors, calipers
Mallet heads, cutting blocks, Instruments
made of or having Delrin® (DupontTM)
surfaces, specula, mixing bowls.
Suction tips, cannulas, needles.

Recommended Cleaning Supplies:
•
•

•

Enzyme solution (i.e. Klenzyme®), detergent (Manu-Klenz®) lukewarm water, soft
bristle brush, and a clean soft towel.
Detergents: Proteolytic enzymatic detergents with a pH range between 6.0 and 8.0
should be used. These detergents have nonionic surfactants. Detergents should be
used in a concentration level recommended by the manufacturer. NOTE: Undiluted
detergents and those with pH's greater than 8.0 can strip the coloration from metal
instruments.
Ultrasonic Cleaners designed for fine cleaning of medical devices.

Cleaning Procedure:
1. Soak for a minimum of two (2) minutes in enzyme solution
2. Rinse thoroughly under lukewarm water
3. Manually clean with a soft bristle brush while immersed in a detergent solution,
paying close attention to crevices and hard-to-clean areas.
a. If using a power washer, close adherence to washer manufacturers’
procedures should be followed.
4. Rinse thoroughly under lukewarm water
5. Dry with a clean soft cloth
6. Visibly examine for damage, rust deposits, and cleanliness.

II

Sterilization Recommendations
Device
Type
Rough
Surfaces
Sliding
Hinges
Lever
Hinges

Prevacuum
Wrapped

Prevacuum
Unwrapped

Gravity
Unwrapped

Gravity
wrapped

EO

Chemical
Disinfectant

Chemical
Sterilant

Peracetic
Acid

Gas
Plasma

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

Screw Pivot

YES

YES

YES

YES

YES

YES

YES

YES

YES

Lumens

YES

YES

YES

YES

YES

YES

YES

NO

YES

YES

YES

YES

YES

YES

YES

YES

NO

NO

YES

YES

YES

YES

YES

YES

YES

YES

YES

Sterilization
Trays
Steam
Sterilizable
Endoscopes

A “NO” indicates Invotec International does not have the data to support the recommendation
of the specific method of sterilization for a given category.

Cycle Parameters

Prevacuum Cycle (wrapped and unwrapped): Three (3) preconditioning pulses with a minimum
exposure time of 4 minutes at 270˚F (132˚C).
Gravity Cycle (wrapped): 270˚F (132˚C) with a minimum exposure time of 15 minutes.
Gravity Cycle (Unwrapped): 270˚F (132˚C) with a minimum exposure time of 10 minutes.
Ethylene Oxide Cycle
Sterilant
Temperature
Humidity
100% EO
131˚F (55˚C)
65-75%
Aerate a minimum of 12 hours at 131 ˚F (55˚C)

Liquid Chemical Cycle
Concentration of
Glutaraldehyde
2.4%
•
•

Temperature
77˚F (25˚C)

Preconditioning
1 hour

Concentration
725 mg/l

Exposure for
Disinfection
45 minutes

Exposure
120-360 minutes

Exposure for
Sterilization
10 hours

Implants are sold as one-time use items and not intended for re-sterilization.
Most reusable instruments are sold nonsterile. These devices should be placed into
suitable packaging for the sterilization process (i.e., central supply wrap (CSR),
autoclave bags, paper/Tyvek® pouches, dedicated sterilization trays and sterilized prior
to use. All instruments should be examined and cleaned prior to sterilization.

III

ACCESSORIES

63-66
67
68
68
68
69

ORO/NAS INS

SPECIALTY PRODUCTS
Lighting Systems
		 Ophthalmic Sponge Packing
		 Cotton Tipped Applicators
		Anti-fog
		Headrest
		 Sterilization Trays

LAR INS

CONTENT

59
59
60

Tracheal T-tubes
Disposable Adenoid Curettes
Surface Electrodes

OTO INS

LARYNGEAL
		
		

PSB

39-40
41
42-43
44-45
46
47
47
48-49
50
51-52
53
54
55

RHI INS

OSSICULAR PROTHESIS
Incus
		Incus-Stapes
		Partial
		Total
		Serenocem
		 Canal Wall
		 Caps and Shoes
		Stapes
		 Bucket Handles
		 Nitinol Stapes
		Instrumentation
		Trials
		Accessories

SPE ACC

27
28
29-30
31
31
32-34
35

LAR ACC

Dressing and Packing
Burs - Ultrabur Drill
Myringotomy Knives & ENT Blades
Phenol Applicator
Myringotomy Kits & Specula
Ventilation Tubes
Otovent® Middle Ear Auto Inflation

OSS

21-23

OTO ACC

OTOLOGY
		
		
		
		
		
		

Rhinologic and Otologic

DIS

DISPOSABLE SUCTIONS

R&CS ACC

RHINOLOGY AND COSMETIC SURGERY
Swiss Therapy™ Cold Therapy
1
		
Scar Sheeting
2
		
Skin Markers
3
		 Micro Electro Dissection Needle
3
		 Chin Implants
4
		 Malar Implants
5
		 Implantable Silicone Blocks
5
		 Nasal Dorsal Implants
6-7
		 Silicone Sheeting, Tubing and Blocks
8
		 Septal Buttons
8
		 Internal Nasal Splints
9-10
		 External Nasal Splints
11
		 Dressing and Packing
12-13
		 Gelatin Packing
14
		
Hyaluronic Acid Gel
15
		 Silicone Epistaxis Balloon
16
		 Rhinology Knives and Blades
17

RHINOLOGY INSTRUMENTS
		
Telescopes
73-74
		Forceps
75-83
		 Antrum Punches, Back Biters and Kerrisons
84-89
		 Nasal Scissors
90-94
		 Knives and Blades
95
		 Osteotomes, Chisels and Saws
96-99
		 Elevators and Probes
100-101
		 Septum Instruments
102-103
		Curettes
104-105
		Speculas
106-108
		 Retractors, hooks
109-112
		Rasps
113-115
		 Sinus Suction Tips
116-117
		Mallets
118
		 Needle Holders, Wire Twisters
119-122
		 Tissue Thumb Forceps
123
		 Miscellaneous Nasal and Sinus
124-126
		 Measuring Instruments
127

PARANASAL, SKULL BASE, PITUITARY INSTRUMENTS
		
Retractors
131

		Forceps

132-133

OTOLOGY INSTRUMENTS
TUNING FORKS

Tuning Forks

137

EXTERNAL EAR CANAL INSTRUMENTS
Ear Speculum
		 Ear Curettes
		 Loops & Hooks
		Probes
		 Tympanum Perforators
		 Ear Catheters
		 Air Bags
		 Powder Blower

138-139
140
141-143
143
144-145
146
147
147

MIDDLE EAR INSTRUMENTS
Instrument Set
		Suctions
		Elevators
		Snares
		Rongeurs
		 Ear Forceps

148
149-150
151-152
153
154
155-160

OTOACC
ACC
OTO

LARYNGEAL INSTRUMENTS

PSB PSB
OTO OTO
INS INS
LAR INSORO/NAS INS
LAR INS

		
		Adenotomes
203
		 Adenoid Currettes
204-206
		 Laryngeal Mirrors
207-208
		 Mouth Gags - Tongue Depressors
209-215
		Retractors
216-218
		 Tongue Spatulas
219-221
		 Nasopharynx Forceps
222-225
		 Tonsil Artery Forceps
226-227
		 Tonsil Seizing Forceps
228-229
		 Tonsil Knives
230-231
		 Tonsil Screws
232
		 Tonsil Dissectors
233-234
		 Tonsil Scissors
235-236
		 Tonsil Snares
237-239
		Tonsiltome
240
		 Tonsilletomy Instruments
241-242
		 Tonsil Needles
243
		Suctions
244-245
		 Tonsil Accessories
246

RHI RHI
INS INS

ORO-NASOPHARYNGEAL INSTRUMENTS

195-198
199
200

SPESPE
ACCACC

BRONCHO-ESOPHAGOSCOPY
Forceps
		Suctions
		Accessories

193-194

LAR
ACC
LAR
ACC

Suctions and Protectors

179-180
181-187
188-189
190-191
192

OSS
OSS

MICRO LARYNGOSCOPY
Operating Largyngoscopes
		 Scissors and Forceps
		 Micro Knives and Elevators
		Suctions
		 Injection Needles
LASER MICRO SURGERY

DIS
DIS

161
162
163
164-165
166-169
170-171
172
173
174
175

R&CS ACC
ACC
R&CS

		 Ear Scissors
		 Malleus Forceps
		Needles/Picks
		Hooks
		 Tympanoplasty Knives
		 Micro Elevators
		 Stapes Curettes
		 Footplate Drill
		Mobilizers
		 Measuring & Cutting

RHINOLOGY & COSMETIC
ACCESSORIES

R&CS ACC
DIS

OTO ACC

OSS
LAR ACC

SPE ACC

RHI INS

PSB

OTO INS

LAR INS

ORO/NAS INS

Swiss Therapy™

•
•
•
•

Moist, but not wet
Lightweight & comfortable
Gently pliable & conforming
Non-adherent

•
•
•
•

R&CS ACC

Invotec’s Swiss Therapy™ Masks and Sheeting are synthesized from a patented Hydrogel material. It
is used as a lightweight and flexible cold compress during and after cosmetic procedures of the face.
Highly patient compliant
Convenient, easy to use
Soothing to skin
Sterile

SWISS THERAPY™ EYE AND FULL FACE MASKS
An easy to use, post-operative cold compress for a variety of plastic surgery or cosmetic
procedures involving the facial area. While comforting to the patient, it reduces post-operative
swelling, redness and discomfort, decreases healing time, and enables the patient to return to
normal activities more quickly, increasing the patient‘s satisfaction.
Superior Post-Operative Compress with Swiss Therapy
• Conforms better to the contours of the face
• Does not leak
• Does not put pressure on or stick to the skin
• Provides superior post-operative wound monitoring, while absorbing and providing pain relief
Number

Description

10-08803

Swiss Therapy™ eye mask

10-08813

Swiss Therapy™ eye mask

10-08820

Swiss Therapy™ Full face mask

Qty/Box
Reinforced

Sterile

3

Sterile

3

Sterile

2

LASER & IPL SKIN THERAPY THROUGH SWISS THERAPY™ SHEET
Provides cooling local anesthetic and pain relieving effects during and after Laser and IPL and
before or after injectable therapies. The immediate application of Swiss Therapy™ provides a
soothing, refreshing, and relaxing feeling. Further, Swiss Therapy™ reduces the risk of hematoma
formation and is beneficial in restoring strength and mobility more quickly so that patients can
heal faster and feel better sooner.
Injection Therapy with Swiss Therapy
Your injectable therapy patient’s aesthetic procedure experience can be optimized via the cooling
comfort provided, before and after injection.
• Soothe the skin, reduce redness
• Minimize skin irritation
• Relieve burning sensations
• Control adverse effects commonly associated with Botox® and other injectable therapies
Laser Therapy with Swiss Therapy
Swiss Therapy™ hydrogel sheeting is a convenient and non-aggressive strategy for cooling and
protecting the epidermis during and after laser and IPL procedures.
• Virtually no prism effect when performing procedures through Swiss Therapy™ sheeting
• Prevents the escape of tissue splatter and smoke plumes, while maximizing patient
comfort
Number

Description

10-08805

Swiss Therapy™ Sheet, 10 cm x 10 cm x 3.5 mm

Qty/Box
Sterile

5

10-08806

Swiss Therapy™ Sheet, 7 cm x 12 cm x 3.5 mm

Sterile

5

10-08807

Swiss Therapy™ Sheet, 5 cm x 9 cm x 3.3 mm

Sterile

5

Swiss Therapy Pad Indications
• Can be used in with all laser systems (Q-switched, pulsed), and arc lamps in the therapeutic wavelength range of 500-1100nm
without affecting transmission of the laser energy. Swiss Therapy should not be used with wavelengths less than 500nm or more
than 1100nm or in laser therapies using lasers with integrated, liquid coolant based cooling systems.
• Non-ablative dermo-cosmetic medical laser products only.

1

Scar Sheeting

R&CS ACC

SILICONE SCAR SHEETS

Transparent, soft, elastic and self-adhesive sheet dressing. Effective in preventing the
formation of new scars and reducing the appearance of existing scars. It is easily applied to
all areas of skin including exposed or hard-to-treat areas like the face, ears, arms, hands and
joints.
• Crystal clear 100% medical grade silicone gel sheeting
• Provides elastic protection to the skin for optimal scar healing
• Durable, comfortable and re-usable
• Various in shapes, sizes and backing colors
• No irritation, no maceration
• Latex free
• Trimmable
• Durable and reusable

2

Number

Description

Size

Gel
Thickness

Qty/
Box

12-75453

Sheet Dressing

75 mm x 45 mm

0.5 mm

10

12-12080

Sheet Dressing

120 mm x 80 mm

0.5 mm

10

12-07603

Nipple Cover

fabric backing

76 mm

0.3 mm

10

12-17603

Areola

fabric backing

76 mm

0.3 mm

10

12-17076

Mastopexy

fabric backing

170 mm x 76 mm

0.3 mm

10

12-25010

Anchor

fabric backing

250 mm x 100 mm 0.3 mm

10

Skin Markers

R&CS ACC

INK SKIN MARKER

The first prep resistant ink skin marker to virtually eliminate the need for remarking of the
patient even after prepping with common alcohol-based antiseptics such as ChloraPrep® or
Duraprep™. Successful in millions of clinical trials, the XL features patent-pending ink that
remains visible after prepping patients.
• Visible up to 10 times longer than traditional ink skin markers
• Ultra Fine Tip
• Sterile
• Includes ruler
Number

Description

1448XLSR

XL Prep Resistant Ink

Qty/
Box
Sterile

100

Micro-Needle

ELECTROCAUTERY DISSECTION MICRO-NEEDLE

•
•
•
•
•
•
•

Blepharoplasty
Incising Temporalis Fascia
Otoplasty
Bicoronal flap
Cleft lip revision
Rhinoplasty

Tungsten tip
Number

Description

29-10000

55 mm long, exposed 3mm tip, straight

Qty/
Box
blue insulated

Sterile

1

3

Facial Implants

R&CS ACC
R&CS ACC

CHIN IMPLANTS
• Soft and flexible implantable grade silicone, packaged sterile • Trims easily for custom fitting
• Tapered edges provide a natural appearance
• White opaque color eliminates transillumination
CONCAVE CHIN, CC-C

STANDARD CHIN
A

B

C

Catalog No.
SC-01
SC-02
SC-03
SC-04
SC-05

A
3.20 cm
3.60 cm
3.90 cm
4.30 cm
4.50 cm

B
0.50 cm
0.60 cm
0.70 cm
0.90 cm
0.90 cm

C
1.30 cm
1.50 cm
1.60 cm
1.80 cm
1.70 cm

Catalog No.
CC-01C
CC-02C
CC-03C
CC-04C
CC-05C

A
3.20 cm
3.40 cm
3.90 cm
4.20 cm
4.70 cm

B
0.40 cm
0.50 cm
0.60 cm
0.70 cm
0.85 cm

C
1.20 cm
1.40 cm
1.60 cm
1.70 cm
1.80 cm

Catalog No.
DCC-1XC
DCC-2XC

DEEP CONCAVE CHIN
STANDARD MALAR - SM
A
B
3.50 cm
0.45 cm
3.60 cm
0.52 cm
A

C
1.40 cm
1.40 cm

DCC-4XC

4.10 cm

1.60 cm

CONCAVE CHIN, CC-C

CONCAVE CHIN

A

B

C
DEEP CONCAVE CHIN, DCC-XC

EXTENDED CHIN - EC

B

D
A

0.70 cm
B

A

Catalog No.
EC-01
EC-02
EC-03
EC-04

B
D

C

DEEP CONCAVE CHIN, DCC-XC

A

A
7.60 cm
7.60 cm
7.60 cm
7.60 cm

EXTENDED CHIN
B
A
0.50 cm
B
0.70 cm
0.80 cm
0.90 cm

D

B

A
EXTENDED ANATOMICAL CHIN
EAC

Catalog No.
EAC-01
EAC-02
EAC-03
EAC-04

D
0.27 cm
0.27 cm
0.27 cm
0.27 cm

A

Apex
C= Thickness at Apex
A

C

D
3.90 cm
4.40 cm
4.80 cm
4.90 cm

EXTENDED ANATOMICAL CHIN A
A
B
C
6.10 cm
0.60Apex
cm
1.20 cm
B
C= Thickness at Apex
6.30 cm
0.70 cm
1.30 cm
TRAPEZOIDAL
6.30 cm
0.80
cm MALAR - TM1.40 cm
6.30 cm
0.90 cm
1.40 cm

B
D

C

C
1.60 cm
1.60 cm
1.70 cm
C
1.70 cm

TRAPEZOIDAL MALAR - TM

A
B
C ANATOMICAL CHIN
EXTENDED
EAC

C

C

STANDARD MALAR - SM

B

C
EXTENDED
CHIN - EC

B

EXTENDED TRAPEZOIDAL MALAR - ETM

A

B

B

MANDIBULAR JOWL - MJ

EXTENDED TRAPEZOIDAL MALAR - ETM

4
D

A

C

A

B
STANDARD MALAR - SM

Facial Implants

C

A

B
STANDARD MALAR - SM

MALAR IMPLANTS

• Soft and flexible implantable grade silicone, packaged sterile
A a natural appearance
• Tapered edges provide
TRAPEZOIDAL MALAR - TM

R&CS ACC
R&CS ACC

C

• Trims easily for custom fitting
• White opaque color eliminates transillumination

B
STANDARD MALAR - SM
A

Catalog No.
SM-01
SM-02
SM-03
SM-04
SM-05

STANDARD MALAR
A
B
2.00 cm
2.70 cm
2.20 cm
3.10 cm
2.50 cm
3.90 cm
2.80 cm
4.50 cm
3.40 cm
5.40 cm

C
0.40 cm
0.50 cm
0.60 cm
0.50 cm
0.60 cm

Catalog No.
TM-01
TM-02
TM-03
TM-04

TRAPEZOIDAL MALAR
A
B
4.10 cm
2.10 cm
4.50 cm
2.20 cm
5.00 cm
2.40 cm
5.40 cm
2.80 cm

C
0.35 cm
0.40 cm
0.45 cm
0.50 cm

Catalog No.
ETM-01
ETM-02
ETM-03
ETM-04

EXTENDED TRAPEZOIDAL MALAR
A
B
4.60 cm
1.80 cm
4.90 cm
2.00 cm
5.20 cm
2.20 cm
5.50 cm
2.20 cm

C
0.40 cm
0.50 cm
0.55 cm
0.60 cm

Catalog No.
AM-01
AM-02
C
AM-03
AM-04

ANATOMICAL MALAR
A
B
3.30 cm
4.20 cm
3.80 cm
4.50 cm
3.90 cm
4.80 cm
4.00 cm
5.40 cm

C
0.30 cm
0.40 cm
0.48 cm
0.65 cm

C

Apex
A
C= Thickness at Apex
TRAPEZOIDAL MALAR - TM

B

B
A

C

Apex
B
C= Thickness at Apex
TRAPEZOIDAL MALAR - TM
EXTENDED TRAPEZOIDAL MALAR - ETM
A
A
Apex
B
C= Thickness at Apex
TRAPEZOIDAL MALAR - TM B
EXTENDED TRAPEZOIDAL MALAR - ETM
A
A
Apex
C= Thickness at Apex

C

B
B

EXTENDED TRAPEZOIDAL MALAR - ETM
C
ANATOMICAL MALAR - AM
A
B
EXTENDED TRAPEZOIDAL MALAR - ETMA
B
ANATOMICAL MALAR - AM
A

B

C
A

C

B
ANATOMICAL MALAR - AM

SILICONE BLOCKS

C

• Non-sterile
• Steam sterilizable
• Implantable grade silicone

A
B
ANATOMICAL MALAR - AM

SILICONE BLOCKS
C

A
B

Catalog No.
SB-01
SB-02
SB-03

A
5.00 cm
6.00 cm
7.00 cm

B
3.00 cm
4.00 cm
5.00 cm

C
1.00 cm
1.50 cm
2.00 cm

C

5

Facial Implants

R&CS ACC

NASAL DORSAL IMPLANTS

•
•
•
•
•

SERIES A

SERIES B

Soft and flexible implantable grade silicone, packaged sterile
Tapered edges provide a natural appearance
Trims easily for custom fitting
White opaque color eliminates transillumination
Over 15 years of clinical history1
Straith, R.E., Five, long-Term Case Reports (Average 15 Years) of Saddlenose Correction Using Cast Silastic Implants. Plastic and Reconstructive Surgery, December, 1991.

1

CND-AC

NOTE: CustomND
prosthesis can be produced to physician’s specifications. Sizers available for all implants.
D

C

B

B
SERIES C

SERIES B

SERIES A

C

A

A

CND-AC
SERIES B, BC
SERIES C, CC
BDepression mostly in nasion area
Depression only at lower edge D
of upper lateral cartilage

SERIES A, AC
ND
Depression equal in both nasion and
lower edge of upper lateral cartilage
C

B

SERIES C

ND-A

SERIES B

C

D

Catalog No.
ND-01A
ND-02A
ND-03A
ND-04A
ND-05A

B

A

C
A

ND-A

A
5.80 cm
5.80 cm
5.80 cm
5.80 cm
5.80 cm

SERIES C

C
3.50 cm
3.50 cm
3.50 cm
3.50 cm
3.50 cm

D
0.20 cm
0.30 cm
0.40 cm
0.50 cm
0.60 cm

C
3.50 cm
3.50 cm
3.50 cm
3.50 cm
3.50 cm

D
0.20 cm
0.30 cm
0.40 cm
0.50 cm
0.60 cm

C
3.50 cm
3.50 cm
3.50 cm
3.50 cm

D
0.30 cm
0.40 cm
0.50 cm
0.60 cm

C
D

CND-ACB

CND-BC

D

B

B

ND-B

C

Catalog No.
CND-1AC
CND-2AC
CND-3AC
CND-4AC
CND-5AC

CND-AC
D A
D

C

B

B

B

A

C
C

ND-B

A
5.80 cm
5.80 cm
5.80 cm
5.80 cm
5.80 cm

B

C

B

CND-BC

ND-C

A

D

B

B

D

B

CND-BC

ND-C

CC

AE

B

A

B
C

C

A

E
A

D-B
B

CND-CC
B

D

6

CND-CC
C

Catalog No.
ND-07B
ND-08B
ND-09B
ND-10B

A
5.80 cm
5.80 cm
5.80 cm
5.80 cm

Catalog No.
CND-9BC
CND-10BC
CND-11BC

A
5.80 cm
5.80 cm
5.80 cm

B
NASAL DORSAL
SERIES
B
D
B
0.80 cm
1.00 cm
C CND-CC
1.10 cm
B
A
E
D
1.20 cm

B

D

D

B

A

NASAL DORSAL SERIES AC
B
D
B
1.00 cm
1.00 cm
C
1.00 cm
A
1.00
cm
1.00 cm
CND-CC

A
A

D

A

NASAL DORSAL SERIES A
A
B
CND-BC
0.75 cm
B
0.90 Dcm
0.90 cm
0.90 cm
1.50 cm

B

C

NASAL DORSAL SERIES BC
B
C
A
E
1.00 cm
3.50 cm
1.00 cm
3.50 cm
1.10 cm
3.50 cm

D
0.50 cm
0.60 cm
0.70 cm

B

ND-A

C

Facial Implants
CND-CC

A

B

CND-BC

A

D

B

Catalog No.
ND-11C
ND-12C
ND-13C
ND-14C

A
5.80 cm
5.80 cm
5.80 cm
5.80 cm

B

Catalog No.
CND-11CC
CND-16CC

A
5.80 cm
5.80 cm

A

ND-B

C
E

D

A

B

NASAL DORSAL SERIES C
B
C
A
E
1.00 cm
3.50 cm
1.00 cm
3.50 cm
1.00 cm
3.50 cm
1.00 cm
3.50 cm

D
0.40 cm
0.50 cm
0.50 cm
0.60 cm

E
0.20 cm
0.30 cm
0.40 cm
0.20 cm

NASAL DORSAL CC
B
C
1.00 cm
3.50 cm
1.10 cm
3.50 cm

D
0.40 cm
0.60 cm

E
0.20 cm
0.50 cm

NASAL DORSAL SERIES COLUMELLA
B
C
D
3.00 cm
0.55 cm
1.10 cm
A
3.00 cm
0.60 cm
1.20 cm
3.10 cm
0.65 cm
1.20 cm
B
C
3.00 cm
0.45 cm
1.10 cm
2.90 cm
0.50 cm
1.10 cm

E
0.60 cm
0.60 cm
0.60 cm
0.60 cm
0.60 cm

C

CND-CC

A

D

B

R&CS ACC

ND-C
C

B

D

B

D

C
A

E

E
A

DORSAL, COLUMELLA, DC-D

D

CONCAVE CHIN, CC-C

C

Catalog No.
DC-06D
DC-07D
DC-08D
DC-09D
DC-10D

A

A
4.70 cm
4.80 cm
4.80 cm
4.80 cm
4.70 cm

E
B

NOTE: Custom prosthesis can be produced to physician’s specifications. Call Invotec for
details.
CRESENT DORSAL COLUMELLA, CDC-DC
D

C

DEEP CONCAVE CHIN, DCC-XC

A

A

C

B

E
B

STANDARD CHIN, SC

A

B
C

7

Sheeting and Tubing

R&CS ACC

MEDICAL GRADE SILICONE SHEETING
Number

MEDICAL GRADE SILICONE TUBING

I.D. x O.D.

Qty/box

Number

5 pair

50-01101

STERILE
20-10680

I.D. x O.D.

Length

NON-STERILE
55 mm x 75 mm x 1.0 mm (2.2 x 3.0 x .040”)

0.012 x 0.025

50’

20-10680S

55 mm x 75mm x 1.0 mm (2.2 x 3.0 x .040”)

10

50-01111

0.020 x 0.037

50’

20-10681

55mm x 75mm x 0.25mm (2.2 x 3.0 x .010”)

10

50-01121

0.025 x 0.047

50’

20-10682

55 mm x 75 mm x 0.5 mm (2.2 x 3.0 x .020”)

5 pair

50-01131

0.030 x 0.065

50’

20-10682S

55 mm x 75 mm x 0.5 mm (2.2 x 3.0 x .020”)

10

50-01141

0.040 x 0.085

50’

20-10685

38 mm x 51 mm x .13 mm (1.5 x 2.0 x .005”)

10

50-01151

0.058 x 0.077

50’

20-10685B

38 mm x 51 mm x .13 mm (1.5 x 2.0 x .005”)

10

50-01161

0.062 x 0.095

50’

20-10686

55 mm x 75 mm x 1.5 mm (2.2 x 3.0 x .060”)

5 pair

50-01171

0.062 x 0.125

50’

20-10686S

55 mm x 75 mm x 1.5 mm (2.2 x 3.0 x .060”)

10

50-01181

0.078 x 0.125

50’

50-01191

0.104 x 0.192

50’

50-01201

0.118 x 0.181

50’

50-01211

0.125 x 0.250

50’

50-01221

0.132 x 0.183

50’

50-01231

0.157 x 0.257

50’

50-01241

0.188 x 0.313

50’

50-01251

0.188 x 0.375

50’

50-01261

0.250 x 0.375

50’

50-01271

0.250 x 0.438

50’

50-01281

0.250 x 0.500

50’

NON-STERILE
20-20680

11 cm x 15 cm x 1.0 mm (4.5 x 6.0 x .040”)

10

20-20682

11 cm x 15 cm x 0.5 mm (4.5 x 6.0 x .020”)

10

20-20685

11 cm x 15 cm x .13 mm (4.5 x 6.0 x .005”)

10

20-20686

11 cm x 15 cm x 1.5 mm (4.5 x 6.0 x .060”)

10

20-30002

30 cm x 30 cm x .06 mm (12 x 12 x .0025”)

1

20-30005

30 cm x 30 cm x .13 mm (12 x 12 x .005”)

1

20-30007

30 cm x 30 cm x .18 mm (12 x 12 x .007”)

1

20-30010

30 cm x 30 cm x .25 mm (12 x 12 x .010”)

1

20-30015

30 cm x 30 cm x .38 mm (12 x 12 x .015”)

1

20-30020

30 cm x 30 cm x .50 mm (12 x 12 x .020”)

1

20-30030

30 cm x 30 cm x .75 mm (12 x 12 x .030”)

1

20-30040

30 cm x 30 cm x 1.0 mm (12 x 12 x .040”)

1

20-30050

30 cm x 30 cm x 1.25 mm (12 x 12 x .050”)

1

Number

20-30060

30 cm x 30 cm x 1.5 mm (12 x 12 x .060”)

1

SB-01

20-30015R

30 cm x 30 cm x .38 mm (12 x 12 x .015”) Reinforced

1

SB-02

20-30020R

30 cm x 30 cm x .50 mm (12 x 12 x .020”) Reinforced

1

SB-03

20-30030R

30 cm x 30 cm x .75 mm (12 x 12 x .030”) Reinforced

1

20-30040R

30 cm x 30 cm x 1.0 mm (12 x 12 x .040”) Reinforced

1

IMPLANTABLE GRADE SILICONE BLOCKS
A

B

C

5.0 cm

3.0 cm

1.0 cm

6.0 cm

4.0 cm

1.5 cm

7.0 cm

5.0 cm

2.0 cm

INVOTEC SEPTAL BUTTONS
•
•
•
•
•

For non-surgical closure of nasal perforations
Can reduce or eliminate crusting, epistaxis, and other symptoms of nasal perforations
Soft 100% medical grade silicone for patient comfort and ease of insertion
Provided sterile, ready to use
Trim to size or custom sizes available upon request
Description

Diameter

IFD

Post Ø

20-10400

Nasal Septal Button

3.2 cm

2.5 mm

6 mm

Sterile

1

20-10400S

Nasal Septal Button

5.0 cm

1.5 mm

8 mm

Sterile

1

Reference:

8

Qty/
Box

Number

Kern, E.B., Facer, G.W., McDonald, T.J., Westood, W.B.
Closure of Nasal Septal Perforations with a Silastic Button: Results in 45 Patients. O.R.L. Digest, Vol. 39, July 1977.

Internal Nasal Splints

X-Large

Regular

R&CS ACC

BREATHE-EASY™ SPLINT

Silicone nasal septal splint with integral airway
• Provides septal support
• Allows nasal breathing post-operative through integral airway
• Pre-punched hole in anterior tip for easier suturing to prevent dislodgement and aid
in septal stabilization
• 100% medical grade silicone for ease of insertion and removal
• Provided sterile, ready to use
Number

Description

Si ze

Dimensions

Height

Qty/Box

20-10500

Breathe-Easy Nasal Splint

Regular

70mm x 25mm

6 mm

5 pair

20-10500BSP Breathe-Easy Nasal Splint

Regular

70mm x 25mm

6 mm

50 pair

20-10510

X-Large

88mm x 40mm

6 mm

5 pair

Breathe-Easy Nasal Splint

PRE-CUT™ SPLINT

Silicone nasal septal splint
• Provides septal support
• Pre-punched hole in anterior tip for easier suturing to prevent dislodgement and aid in
septal stabilization
• 100% medical grade silicone for ease of insertion and removal
• Provided sterile, ready to use
Number

Description

20-10505

Pre-Cut Nasal Splint

Qty/Box
Sterile

5 pair

DEMPSEY SPLINT

Fluoroplastic internal nasal splint
• 100% Fluoroplastic to reduce or prevent adhesions between the septum and lateral
nasal wall by stabilizing the turbinates
• Easy insertion and removal
• Provided sterile, ready to use
Number

Description

20-10602

Dempsey Medium

Qty/Box
Sterile

10 pair

20-10603

Dempsey Large

Sterile

10 pair

20-10602C

Dempsey, Medium, Clear

Sterile

10 pair

20-10603C

Dempsey, Large, Clear

Sterile

10 pair

K-SPLINT™

Designed to be used for endoscopic sinus surgery or any other procedure where middle
turbinate adhesions or lateralizations are problematic
• Easy to shape and configure to patient’s septum and middle turbinate anatomy
• Available in four sizes to reduce sizing time in the operating room
• Made of easy to see white malleable fluoroplastic
• Supplied sterile for immediate surgical usage
• Designed by J. Patrick Shea, M.D.
Number

Description

Qty/Box

20-10640

Small

Sterile

5 pair

20-10641

Medium/Small

Sterile

5 pair

20-10642

Medium

Sterile

5 pair

20-10644

Large

Sterile

5 pair

9

Internal Nasal Splints

R&CS ACC

GUASTELLA/MANTOVANI™ INTERNAL NASAL SPLINT
• Designed for functional and/or aesthetic rhinosurgery of the septal valve nose tip
and
nasal pyramid
• Shaped to support the tip of the nose
• Made from 100% Fluoroplastic
• Packaged sterile, ready to use
Number

Description

20-10630

Guastella/Mantovani Internal Nasal Splint

Reference:

Qty/Box
.25mm

5 pair

Mantovani, M., Guastella, C., Mazzola, R.
The Guastella/Montovani Septal-Valve Splint: An Intranasal
Biplanar and Multivectorial Orthopedic Device
Plastic and Reconstructive Surgery, Vol. 106, August, 2000

BIVALVE SPLINTS

Nasal Septal Splints

• 100% Fluoroplastic to reduce or
prevent adhesions between the septum
and lateral nasal wall
• Easy insertion and removal

• Pre-punched suture holes
• Over 30 years of clinical use
• Provided sterile and ready to use

CUSTOM-CUT™ SPLINTS
• Provided sterile and ready to use
• Five thicknesses available

• Choice of 100% Fluoroplastic or
100% medical grade silicone
• Allows for custom design by the
surgeon

10

Number

Size

Description

Thickness

Qty/box

20-10650

Standard

Bivalve Splint

.25mm

Sterile

5 pair

20-10650S

Standard

Bivalve Splint

.25mm

Sterile

10 ea

20-10655

Standard

Bivalve Splint

.50mm

Sterile

5 pair

20-10655S

Standard

Bivalve Splint

.50mm

Sterile

10 ea

20-10660

Large

Bivalve Splint

.25mm

Sterile

5 pair

20-10660S

Large

Bivalve Splint

.25mm

Sterile

10 ea

20-10665

Large

Bivalve Splint

.50mm

Sterile

5 pair

20-10665S

Large

Bivalve Splint

.50mm

Sterile

10 ea

20-10670

38mm x 64mm

Custom-Cut Fluoroplastic

.25mm

Sterile

5 pair

20-10675

38mm x 64mm

Custom-Cut Fluoroplastic

.50mm

Sterile

5 pair

20-10680

55mm x 75mm

Custom-Cut Silicone

1.0mm

Sterile

5 pair

20-10680S

55mm x 75mm

Custom-Cut Silicone

1.0mm

Sterile

10 ea

20-10681

55mm x 75mm

Custom-Cut Silicone

.25mm

Sterile

10 ea

20-10682

55mm x 75mm

Custom-Cut Silicone

.50mm

Sterile

5 pair

20-10682S

55mm x 75mm

Custom-Cut Silicone

.50mm

Sterile

10 ea

20-10685

38mm x 50mm

Custom-Cut Silicone

.13mm

Sterile

10 ea

20-10685B

38mm x 50mm

Custom-Cut Silicone, Blue

.13mm

Sterile

10 ea

20-10686

55mm x 75mm

Custom-Cut Silicone

1.5mm

Sterile

5 pair

20-10686S

55mm x 75mm

Custom-Cut Silicone

1.5mm

Sterile

10 ea

External Nasal Splints

R&CS ACC

SOFT-FORM™ THERMOPLASTIC NASAL SPLINT

• Standard sizes or exclusive Invotec’s Custom-Cut™ to design your own
• Easy to apply - adhesive backing
Number

Description

Qty/Box

20-10100

External Nasal Splint

small

single

20-10101

External Nasal Splint

small

kit

20-10110

External Nasal Splint

regular

single

20-10111

External Nasal Splint

regular

kit

20-10120

External Nasal Splint

custom-cut, 2 x 3 in

single

20-10121

External Nasal Splint

custom-cut, 2 x 3 in

kit

20-10125

Large Sheet

8.5 x 11 in

Cut to size

1

20-10130

External Nasal Splint

large

single

10

20-10131

External Nasal Splint

large

kit

10
5 kits*
10
5 kits*
10
5 kits*

5 kits*

SOFT-FORM AL™ PADDED ALUMINUM NASAL SPLINT

• Easy to remove for patient comfort
• Three standard sizes
• Easy to apply - adhesive backing
Number

Description

Qty/Box

20-10200

External Nasal Splint

small

single

20-10201

External Nasal Splint

small

kit

20-10210

External Nasal Splint

regular

single

20-10211

External Nasal Splint

regular

kit

20-10220

External Nasal Splint

large

single

20-10221

External Nasal Splint

large

kit

10
5 kits*
10
5 kits*
10
5 kits*

SOFT-FORM AL-D™ PADDED ALUMINUM NASAL SPLINT
• Three standard sizes
• Easy to apply - adhesive backing
Number

Description

Qty/Box

20-10300

External Nasal Splint

small

single

20-10301

External Nasal Splint

small

kit

20-10310

External Nasal Splint

regular

single

20-10311

External Nasal Splint

regular

kit

20-10320

External Nasal Splint

large

single

20-10321

External Nasal Splint

large

kit

10
5 kits*
10
5 kits*
10
5 kits*

SOFT-FORM AL-B™ ALUMINUM NASAL SPLINT
• Two standard sizes
Number

Description

20-10300B

External Nasal Splint

small

single

10

20-10310B

External Nasal Splint

medium

single

10

* Complete kits conta
(1) Sterile skin prep
(1) Sterile alcohol sp
(1) Nasal Splint
(1) Dorsum pad
(6) Sterile 12mm x 1

Qty/Box

11

Rhinologic Sponge Packing

R&CS ACC

PVA+™ SPONGE PACKING
•
•
•
•
•

Bacteriostatic agent inhibits the growth of bacteria* on the sponge for up to 7 days
PVA+ helps reduce odor caused by bacteria compared to standard PVA
Ideal for Nasal, Epistaxis or Sinus control
Double compressed for easy insertion
PVA+ is biocompatible, bacteriostatic, and very hydrophilic
Number

Description

Dimensions

22-66400

PVA+ Nasal Dressing, Small

4.5 x 1.5 x 2 cm

10

22-66402

PVA+ Nasal Dressing, Large

8.0 x 1.5 x 2 cm

10

22-66406

PVA+ Epistaxis Dressing, Large

10 x 1.5 x 2.5 cm

10

22-66409

PVA+ Standard Nasal Dressing with Airway,
Small

4.5 x 1.5 x 2.0 cm

10

22-66410

PVA+ Standard nasal Dressing with Airway,
Large

8.0 x 1.5 x 2.0 cm

10

22-66411

PVA+ Anatomical Nasal Tampon with Airway

8.0 x 1.5 x 3.0 cm

10

22-66413

PVA+ Anatomical Nasal Tampon

8.0 x 1.5 x 3.0 cm

10

22-66421

PVA+ Epistaxis Dressing, Small

5.5 x 1.5 x 2.5 cm

10

22-66426

PVA+ Sinus Dressing, Small

3.5 x 0.9 x 1.2 cm

10

22-66427

PVA+ Sinus Dressing

2.5 x 0.9 x 2.0 cm

10

22-66428

PVA+ Sinus Dressing

4.5 x 0.9 x 2.0 cm

10

*Yersinia Entercolitica, Serratia Mecrecesens and Bacillus Subtilis

12

Qty/Box

Rhinologic Sponge Packing

•
•
•
•

R&CS ACC

PVA SPONGE PACKING
Soft, comfortable and conforming
Packaged compressed and sterile
Easily trimmed with scissors
Small pore size minimizes tissue ingrowth

Standard
Invotec
Number

Merocel®
Number

Description

Dimensions

22-60400

440400

Nasal Dressing, small

4.5 x 1.5 x 2.0 cm

10

22-60400P

400400

Nasal Dressing without string,
small

4.5 x 1.5 x 2.0 cm

10

22-60402

440402

Nasal Dressing, large

8.0 x 1.5 x 2.0 cm

10

22-60402P

400402

Nasal Dressing without string

8.0 x 1.5 x 2.0 cm

20

22-60409

440409

Nasal Dressing with airway,
small

4.5 x 1.5 x 2.0 cm

10

22-60409P

400409

Nasal Dressing with airway
without string

4.5 x 1.5 x 2.0 cm

10

22-60410

440410

Nasal Dressing, with airway,
large

8.0 x 1.5 x 2.0 cm

10

22-60410P

400410

Nasal Dressing, with airway
without string, large

8.0 x 1.5 x 2.0 cm

10

22-60411

440411

Anatomical Nasal Tampon with
airway

8.0 x 1.5 x 3.0 cm

10

22-60411P

400411

Anatomical Nasal Tampon with
airway without string

8.0 x 1.5 x 3.0 cm

10

22-60413

440413

Anatomical Nasal Tampon

8.0 x 1.5 x 3.0 cm

10

22-60413P

400413

Anatomical Nasal Tampon
without string

8.0 x 1.5 x 3.0 cm

10

22-60414

440413

Slimline Anatomical Nasal
Tampon

8.0 x .75 x 3.0 cm

10

Qty/Box

Anatomical

Epistaxis Products
22-60406

440406

Posterior Epistaxis Tampon

10.0 x 1.5 x 2.5
cm

10

22-60406P

400406

Posterior Epistaxis Tampon
without string

10.0 x 1.5 x 2.5
cm

10

22-60421

400421

Anterior Epistaxis Tampon

5.5 x 1.5 x 2.5 cm

10

Sinus Packs and Dressings
22-60423

400423

Sinus Kit

4.5cm sinus, 7.5cm nasal

10 pair

22-60426

400426

Sinus Dressing

3.5 x 0.9 x 1.2 cm

10 pair

22-60427

400427

Sinus Dressing

2.5 x 0.9 x 2.0 cm

10 pair

22-60428

400428

Sinus Dressing

4.5 x 0.9 x 2.0cm

10 pair

22-60530

400530

Sinus Dressing, slim

3.5 x 0.6 x 1.2 cm

10 pair

22-60531

400531

Sinus Dressing, slim

2.5 x 0.6 x 2.0 cm

10 pair

22-60582

400582

Sinus Dressing, slim

4.5 x 0.6 x 2.0 cm

10 pair

13

Gelitan Packing

R&CS ACC

GELATIN SPONGES AND FILM USP

Indicated for use to control minimal bleeding by tamponade effect, blood absorption
and platelet aggregation following ENT surgery and to prevent adhesions in the
nasal cavity. Gelitan sponges are effective in supporting the new graft in the outer
ear canal after tympanoplasty and buttressing middle ear implants.

Sponge and Film

Number

Description

Dimensions

Qty/
Box

Size

EQU60-20-07

EquiSpon® Sponge

60 x 20 x 7 mm

12-7

Sterile

10

EQU125-80-10

EquiSpon® Sponge

125 x 80 x 10 mm

100

Sterile

5

EQUF200-70-05

EquiSpon® Film

200 x 70 x 5.0 mm

Sterile

10

EQU80-50-10

EquiSpon® Sponge

80 x 50 x 10 mm

Sterile

10

50

EQUI-SPON® POWDER
Number
Powder

Qty/
Box

Description

EQP-01

Equi-Spon® Powder, 1 gram

Sterile

4

EQP-01K

Equi-Spon® Hemostat Kit
Includes: Two (2) 10 cc LL syringes, 18g needle,
Flexible applicator cannula, 1gm Equi-Spon Porcine
Powder with Mixing container

Sterile

5

GELITAN SPONGE TAMPON
Cylinder

14

Number

Description

Dimensions

EQU80-30-00

Gelitan Sponge, Fenestrated Cylinder

80 x 30 mm

Qty/
Box
Sterile

5

PureRegen

R&CS ACC

PureRegen™

Injectable Crosslinked Hyaluronic Acid Nasal Packing and Stent
PureRegen® injectable nasal packing is formulated to be used as a nasal dressing
and stent, separating nasal structures following nasal and sinus surgical procedures.
PureRegen® bioresorbable nasal packing and stent is a non-pyrogenic, transparent,
specifically formulated viscoelastic gel of self-cross-linked hyaluronan derived
from nonanimal sources. This patented formulation ensures the material maintains
the best possible stability during its storage and clinical use. Unlike esterified HA,
PureRegen® Gel has not been reported as osteogenic in the nasal cavities.
PureRegen® Gel absorbs body fluids and blood resulting in its expansion gradually
up to 50% by volume. The volume of the injected gel secures its initial stability within
sinus cavity and controls minimal bleeding by tamponade effect.
•
•
•
•
•
•

Controls minimal bleeding and oozing
Clinically tested effective adhesion prevention
Facilitates wound healing and functional mucociliary regeneration
Provides moist wound environment
Degradable - No need for painful traumatic removal
Predictable retention - Gradually resorbs over 7-14 days

Number

Description

PR-00005

PureRegen™ gel 5 ml prefilled glass syringe with malleable
cannula, sterile

Qty/
Box
1

15

Silicone Epistaxis Balloon

R&CS ACC

ULTRA-STAT™
Epistaxis nasal balloon with integral airway
• Designed for fast control of intra-nasal bleeding and patient comfort
• Bevelled posterior tip and soft silicone construction provide for easy placement
• Two silicone balloons independently filled facilitate pressure control in both the
anterior and posterior chambers
• 100% soft medical grade silicone for patient comfort when inserting
• Integral airway allows for nasal breathing
• Silicone construction prevents adhesion for easy removal
• Provided sterile with or without inflation syringe
Number

Description

Qty/Box

20-10700

Ultra-Stat Epistaxis Balloon with syringe

Sterile

1

20-10701

Ultra-Stat Epistaxis Balloon

Sterile

1

POST-STAT™
Posterior nasal packing and suction channel
• Excellent for control of posterior intra-nasal bleeding
• Low profile design to maximize working space
• Multi-port suction/irrigator catheter inhibits clogging and provides for clear working area
• Soft silicone construction provides for low cuff pressure and re-sterilization
• Silicone construction prevents adhesion for easy removal
• Provided sterile with inflation syringe
Number

Description

20-10710

Post-Stat Epistaxis Balloon with syringe

Qty/Box
Sterile

1

QUICK-PACK™
With airway
• Designed for nasal packing following septal, rhinoplasty, or other intra-nasal
procedures
• 100% medical grade silicone reduces or prevents adhesion allowing for patient comfort in
use and during removal
• Integral airway allows for nasal breathing
• Provided sterile with inflation syringe

16

Number

Description

20-10715

Quick-Pack Nasal Packing with syringe

Qty/Box
Sterile

2

Rhinology Knives and Blades

Description

Qty/Box

65-8900

Spear Tip with handle

Angled

Sterile

4

65-8920

Sickle Tip with handle

Straight

Sterile

4

65-9610

Uncinate with handle

Sterile

4

Number

Description

65-6001

Septotome

R&CS ACC

Number

Qty/Box
Angled 90°

Sterile

6

17

R&CS ACC

DISPOSABLE SUCTIONS

DIS
OTO ACC

OSS
LAR ACC

SPE ACC

RHI INS

PSB

OTO INS

LAR INS

ORO/NAS INS

Disposable Suctions

HOUSE/HOUGH STYLE HANDLE
• Used as a connector between the suction tip and the suction tubing
• Sterile, packaged in individual peel pouch
Rhinologic / Otologic
Description

Qty/Box

30-10001

Suction Controller, black

20

30-10000

Elongated House/Hough style handle with finger control hole, 3”

20

DIS

Number

HANDLES
Number

Description

Qty/Box

Number

Description

NZ3238-100

Suction controller, black, with finger hole

Qty/Box
Non-sterile

100

METAL SUCTION TIP
•
•
•
•
•

Applicable for ear examinations, suction of wax and other fluids, paracentesis
The curved angle is specially designed for microscopic examination and surgery
Quick connector suction tip handle is easy to change during surgery
Sterile, packaged in individual peel pouch
Available in broad variety of lumen sizes

Rhinologic
Number

Description

Color

Qty/Box

30-08004

0.4 mm x 80 mm

Gray

20

30-08007

0.7 mm x 80 mm

Black

20

30-07010

1.0 mm x 70 mm, 3 Fr

White

20

30-08010

1.0 mm x 80 mm, 3 Fr

White

20

30-07014

1.4 mm x 70 mm, 4 Fr

Red

20

30-08014

1.4 mm x 80 mm, 4 Fr

Red

20

30-08020

2.0 mm x 80 mm, 14 g, 6 Fr

Green

20

30-08025

2.5 mm x 80 mm, 7.5 Fr

Transparent

20

30-08030

3.0 mm x 80 mm, 9 Fr

Transparent

20

30-08040

4.0 mm x 80 mm, 12 Fr

Transparent

20

30-10010

1.0 mm x 100 mm, 3 Fr

White

20

30-10014

1.4 mm x 100 mm, 4 Fr

Red

20

30-10020

2.0 mm x 100 mm, 6 Fr

Green

20

30-10025

2.5 mm x 100 mm, 7 Fr

Transparent

20

30-10030

3.0 mm x 100 mm, 9 Fr

Transparent

20

21

Disposable Suctions

DIS

METAL ROSEN-HOUSE STYLE SUCTION NEEDLE
Number

Description

Dimensions

Color

Qty/Box

30-07004

Micro suction tip

0.4 mm x 70 mm, 26 G

Gray

20

30-08004

Micro suction tip

0.4 mm x 80 mm, 26 G

Gray

20

30-07007

Micro suction tip

0.7 mm x 70 mm, 22 G

Black

20

30-08007

Micro suction tip

0.7 mm x 80 mm, 22 G

Black

20

30-07010

Micro suction tip

1.0 mm x 70 mm, 20 G, 3 Fr

White

20

30-07014

Micro suction tip

1.4 mm x 70 mm, 18 G, 4 Fr

Red

20

30-08014

Suction tip

1.4 mm x 80 mm

Red

20

30-07020

Suction tip

2.0 mm x 70 mm, 14 G, 5 Fr

Green

20

30-08020

Suction tip

2.0 mm x 80 mm

Green

20

30-08030

Micro suction tip

3.0 mm x 80 mm, 9 Fr

Transparent

20

30-08040

Suction tip

4.0 mm x 80 mm

Transparent

20

FRAZIER/FERGUSON NASAL STYLE SUCTION
• Designed for Rhinology surgery or examination
• Suction tip made of medical grade stainless steel
• Sterile, packed in individual peel pouch
• Available with one side hole (velvet eye) at tip end to avoid biopsy effect (tissue
damage)
Number

Description / Dimensions

Color

Qty/Box

30-14020

2.0mm x 140 mm, 6 Fr

10

30-14030

3.0mm x 140 mm, 9 Fr

10

30-14040

4.0mm x 140 mm, 12 Fr

10

SUCTION TUBING

22

Number

Description

66153510

Suction Tubing for metal tips

Length
PVC

3.5 mm length

Qty/Box
5

R&CS ACC

DIS

ACCESSORIES

OTOLOGY

OTO ACC
OSS
LAR ACC

SPE ACC

RHI INS

PSB

OTO INS

LAR INS

ORO/NAS INS

Otologic Dressing & Packing

EAR PROTECTOR KITS

•
•
•
•

Lightweight yet stable, will not slide
Adjustable velcro straps
Comfortable
Latex-free

• Easy to apply
• Exerts even, consistent pressure
• Sterile

Number

Description

Qty/Box

90-11000

Hard Ear Dressing Kit - adult size
Includes: 10 - 4 x 4” gauze sponges, 1 Telfa™ pad

Sterile

10 kits

90-15005

Soft Ear Dressing Kit
Includes: 4 - 4 x 4” gauze sponges, 1 Telfa™ pad

Sterile

10 kits

OTO ACC

MALLEABLE EAR DRESSING
• A soft malleable bandage that can conform to and retain the shape of the external ear
• Smooth, non-adherent silicone surface with a thin malleable metallic layer
• As suggested by Frederick Godley, MD, Providence, RI
Number

Description

90-20000

Malleable ear compression dressing

Qty/Box
10

90-21000

Thermoplastic ear compression dressing

5

OTOLOGY PACKING STRIPS
•
•
•
•

Designed to protect the tympanic membrane following middle ear surgery
Available in blue to provide greater visibility in the ear canal
Rosette packing
Provided sterile, 3 per pack
Number

Description

Dimensions

27-10000

Clear silicone

6 x 20 x 0.13 mm

Qty/Box
30

27-10000B

Blue silicone

6 x 20 x 0.13 mm

30

27-10001

Clear silicone

6 x 40 x 0.13 mm

30

27-10001B

Blue silicone

6 x 40 x 0.13 mm

30

20-10685

Clear silicone sheeting

38 x 50 x 0.13 mm

10

20-10685B

Blue silicone sheeting

38 x 50 x 0.13 mm

10

For a complete line of silicone sheeting available see Sheeting and Tubing.

EAR WICKS
• PVA ear packs are soft, comfortable, conforming, absorbs quickly and expands evenly
• Packaged compressed and sterile
Number

Description

Dimensions

22-60108

Ear Wick

9 mm x 15 mm

Qty/Box
20

22-65108

Ear Wick

9 mm x 15 mm

50

22-60110

Ear Wick - long

9 mm x 24 mm

20

22-65110

Ear Wick - long

9 mm x 24 mm

50

22-66108

PVA+ Ear Wick

9 mm x 15 mm

20

22-66110

PVA+ Ear Wick

9 mm x 24 mm

20

25

Burs

ULTRABUR OTOLOGIC DRILL

• Hand-held microdrill for stapedotomy, stapedectomy, and fashion of homo/auto bone
grafts
• Narrow, lightweight design allows for better visualization in middle ear
• Speed: 7,000 rpm max
• Provided sterile

OTO ACC

Number

Qty/Box

10-3030

Diamond tip

0.6 mm

1

10-3031

Diamond tip

0.7 mm

1

10-3038

Diamond tip

0.8 mm

1

BURS

• Designed for use with straight shank drill systems and Xomed® power hand pieces
• Multiple uses
• Provided sterile
Round Carbide
Number w/ Notch

w/o Notch

Head Diameter
(mm)

Length (mm)

Number of
Flutes

BC-70050

BC-70050P

0.5

70

4

BC-70100

BC-70100P

1.0

70

6

BC-70150

BC-70150P

1.5

70

6

BC-70200

BC-70200P

2.0

70

6

BC-70250

BC-70250P

2.5

70

6

BC-70300

BC-70300P

3.0

70

8

BC-70350

BC-70350P

3.5

70

8

BC-70400

BC-70400P

4.0

70

8

BC-70450

BC-70450P

4.5

70

10

BC-70500

BC-70500P

5.0

70

10

BC-70550

BC-70550P

5.5

70

10

BC-70600

BC-70600P

6.0

70

10

BC-70650

BC-70650P

6.5

70

10

BC-70700

BC-70700P

7.0

70

12

BC-70000

BC-70000P

Complete Set - one of each

Round Diamond Bur
Number w/ Notch

w/o Notch

Head Diameter
(mm)

Length (mm)

Style

BD-70050

BD-70050P

0.5

70

Diamond

BD-70100

BD-70100P

1.0

70

Diamond

BD-70150

BD-70150P

1.5

70

Diamond

BD-70200

BD-70200P

2.0

70

Diamond

BD-70250

BD-70250P

2.5

70

Diamond

BD-70300

BD-70300P

3.0

70

Diamond

BD-70350

BD-70350P

3.5

70

Diamond

BD-70400

BD-70400P

4.0

70

Diamond

BD-70500

BD-70500P

5.0

70

Diamond

BD-70600

BD-70600P

6.0

70

Diamond

BD-70000

BD-70000P

O225300

26

Xomed® is a registered trademark of Medtronic - Xomed

Complete Set - one of each
Bur Rack - Holds 34 straight shaft burs, length 70 mm

Myringotomy Knives and ENT Blades

MYRINGOTOMY MICRO BLADES, MALLEABLE TAPERED SHAFT
• Sterile
Number

Description

60-08230

Micro Otologic Blade

Qty/Box
Upcutting

Angled

6

60-08231

Micro Otologic Blade

Downcutting

Angled

6

60-08232

Micro Otologic Blade

Razor

Straight shank

6

60-08233

Micro Otologic Blade

Spear

Angled

6

60-08234

Micro Otologic Blade

Spear

Straight shank

6

60-44820

Stainless steel handle for tapered blades

1

OTO ACC

MYRINGOTOMY KNIVES AND BLADES, FLAT SHAFT ANGLED
• Sterile
Number

Description

60-45010

Lance

Adult

Down cut

Qty/Box
6

60-45020

Lance w/ handle

Adult

Down cut

6

60-45030

Lance

Adult

Up cut

6

60-45040

Lance

Pediatric

Down cut

6

60-45050

Lance with handle

Pediatric

Down cut

6

60-45070

Spear

Pediatric

6

60-45080

Spear with handle

Pediatric

6

65-8154

Narrow arrow knife

Straight

6

MULTI-USE MYRINGOTOMY KNIVES WITH PROTECTIVE CAP
• Non-sterile, Auto-clavable
Number

Description

Qty/Box

34-2123

Lance

up cut

3

34-2124

Lance

down cut

3

TYMPANOPLASTY BLADES
• Sterile
Number

Description

60-46080

Tympanoplasty

angled

Qty/Box
6

60-46090

Tympanoplasty

straight

6

60-46100

Sickle blade

6

SPECIALTY MINI BLADES
• Sterile
Number

Description

Qty/Box

65-6400

Round tip sharp

12

65-6500

15° pointed

12

65-6600

Lamellar blade straight

6

65-6900

Straight 180° cutting surface

6

27

Myringotomy Knives and ENT Blades

MYRINGOTOMY KNIVES AND BLADES, MALLEABLE ROUND SHAFT

OTO ACC

• Sterile
Number

Description

Qty/Box

60-44010

Lance

Straight shaft

Adult

6

60-44015

Lance

Angled shaft

Adult

6

60-44020

Lance w/ handle

Straight shaft

Adult

6

60-44025

Lance w/ handle

Angled shaft

Adult

6

60-44040

Lance on round handle

Straight shaft

Pediatric

6

60-44045

Lance on round handle

Angled shaft

Pediatric

6

60-44046

Lance on round handle

Angled shaft

Pediatric

6

60-44023

Lance w/ handle

Straight shaft

60-40716

Lance w/ flat black handle

Straight shaft

60-44070

Spear Tip

Straight shaft

Pediatric

6

60-44075

Spear Tip

Angled shaft

Pediatric

6

60-44080

Spear Tip w/ handle

Straight shaft

Pediatric

6

60-44085

Spear Tip w/ handle

Angled shaft

Pediatric

6

65-8324

Bayonet Spear - w/ handle

60-40715

Sickle w/ flat black handle

Straight shaft

6

60-45090

Sickle knife

Straight shaft

6

60-44090

Sickle tipped knife on
round handle

Round shaft

6

6
6

6

STAINLESS STEEL CHUCK STYLE HANDLES
• Non-Sterile

28

Number

Description

Qty/Box

60-44200

Stainless steel handle for flat stock knives

10 cm
10 cm

1

60-44210

Stainless steel handle for round stock knives

60-44820

Stainless steel handle for tapered knives

1

1

60-44201

Replacement collet for handle #60-44200

1

Myringotomy Knives and ENT Blades

EAR CURRETTE
• Non-Sterile
• Carbon fiber filled nylon
Number

Description

Qty/Box

NZ3431-100 Ear Curette

3mm loop

100

NZ3432-100 Ear Curette

2.5mm loop

100

NZ3441-100 Cerumen Hook, non-sterile

100

NZ3461-100 Rosen needle, slight curve

100

OTO ACC

Phenol Applicator

• Reusable
Number

Description

O99610

Phenol applicator

Qty/Box
1

29

OTO ACC

• Reusable

30

Number

Description

O99610

Phenol applicator

Qty/Box
1

Myringotomy Kits and Ear Specula

INVOTEC EAR SPECULA
•
•
•
•
•
•

New oval design of the cone and oblique cut end for improved line of sight
New, wider, rim on the grip side for better stability when hand held
For examination procedures
Fits Peter’s or Siegler’s pneumatic otoscopes
Hygienically packed
Latex and PVC-free
Number

Description

Qty/Box

Sterile
2.5 mm specula

OTO ACC

606625S

10

606640S

4 mm specula

10

606650S

5 mm specula

10

606660S

6 mm specula

10

606670S

7 mm specula

10

606680S

8 mm specula

10

2.5 mm specula

20

Non-Sterile
606625
30-00030

3.0 mm specula

20

30-30040

4 mm specula

20

30-00050

5 mm specula

20

30-00060

6 mm specula

20

606670

7mm specula

20

606680

8mm specula

20

DISPOSABLE MYRINGOTOMY KIT
• A ready made kit for Paracentisis Surgery
• Sterile, single-use
Number

Description

Qty/Box

NZ3246

Myringotomy Kit:
(1) Myringotomy Knife, (1) Jobson Home Probe, (1) Rosen
Inserter, (2) Bent suction tubes -16g and 20g, (1) Suction
controller, (3) Specula - 4 mm, 5 mm, and 6 mm.

1

NZ3248B-5

Myringotomy Kit with 8 cm Forceps:
(1) Myringotomy Knife, (1) Jobson Home Probe, (1) Rosen
Inserter, (2) Bent suction tubes -16g and 20g, (1) Suction
controller, (3) Specula - 4 mm, 5 mm, and 6 mm, (1) Forceps Stainless Steel - 7, Jaw.

1

NZ3270

Myringotomy Kit with Stainless Steel Forceps:
(1) Myringotomy Knife, (1) Jobson Home Probe, (1) Rosen
Inserter, (2) Bent suction tubes -16g and 20g, (1) Suction
controller, (3) Specula - 4 mm, 5 mm, and 6 mm, (1) Forceps Stainless Steel - 3.5 mm, Jaw.

1

NZ3271B-5

Pediatrics Myringotomy Kit:
(1) Myringotomy Knife, (1) Jobson Home Probe - Oval, (1)
Rosen Inserter, (2) Bent suction tubes -16g and 18g, (1) Suction
controller, (3) Ear Specula - 3 mm, 4 mm, and 5 mm, (1) Forceps Stainless Steel - Ultra fine.

1

31

Ventilation tubes

ARMSTRONG GROMMET
Number

Description

23-50800

Armstrong Grommet

Sterile

Material

ID

Silicone

1.14 mm

Material

ID

FLPL

1.14 mm

Material

ID

Silicone

1.14 mm

Material

ID

FLPL

1.27 mm

Material

ID

FLPL

1.14 mm

Qty/Box
10

OTO ACC

MODIFIED ARMSTRONG GROMMET
Number

Description

23-40810

Modified Armstrong Grommet

Sterile

Qty/Box
10

ARMSTRONG STRAIGHT SHANK
12mm

Number

Description

23-50801

Armstrong Straight Shank

Sterile

Qty/Box
10

BAXTER BUTTON
I.D.

Number

Description

23-41300

Tapered Lumen

Sterile

Qty/Box
10

BEVELED BOBBIN
Number

Description

23-41310

Beveled Bobbin

Sterile

Qty/Box
10

DONALDSON STYLE
Number

Description

Material

ID

23-40200

Donaldson Grommet

Sterile

FLPL

1.14 mm

Qty/Box
10

23-40201

Donaldson Grommet with wire

Sterile

FLPL

1.14 mm

10

23-50200

Donaldson Grommet with tab

Sterile

Silicone

1.14 mm

10

23-50210

Donaldson Grommet without tab

Sterile

Silicone

1.14 mm

10

Material

ID

FLPL

0.76 mm

Material

ID

MINI TEF FLUOROPLASTIC
Number

Description

23-42076

Invotec Tiny Tef

Sterile

Qty/Box
10

PAPARELLA STYLE

Paparella I

Paparella II

Number

Description

Qty/Box

23-50700

Paperella I

Sterile

Silicone

1.00 mm

10

23-50720

Paperella I

Sterile

Silicone

1.14 mm

10

23-50710

Paperella II

Sterile

Silicone

1.50 mm

10

Material

ID

PE

1.14 mm

POPE BEVELED GROMMET

32

Number

Description

23-41800

Angled Flanges, Blue

Sterile

Qty/Box
10

Ventilation tubes

REUTER BOBBIN STYLE
Number

Description

ID

23-40400

Reuter Bobbin

23-40400B

Reuter Bobbin - Blue

23-40401
23-60400

Qty/Box

Sterile

FLPL

1.14 mm

10

Sterile

FLPL

1.14 mm

10

Reuter Bobbin with wire

Sterile

FLPL

1.14 mm

10

Reuter Bobbin

Sterile

Titanium

1.14 mm

10

23-60401

Reuter Bobbin with wire

Sterile

Titanium

1.14 mm

10

23-60427

Reuter Bobbin

Sterile

Titanium

1.27 mm

10

23-61401

Reuter Bobbin

Sterile

Titanium

1.09 mm

10

Material

ID

OTO ACC

Material

SHAH STYLE
Number

Description

Qty/Box

23-40500

Shah Grommet

Sterile

FLPL

1.14 mm

10

23-40501

Shah Grommet with wire

Sterile

FLPL

1.14 mm

10

Material

ID

Silicone

1.02 mm

Material

ID

SHEA PARASOL VENT TUBE
ID

Number

Description

23-50536

Shea Parasol with tab

Sterile

Qty/Box
10

SHEEHY COLLAR BUTTON
Number

Description

Qty/Box

10076

Sheehy Collar Button

Sterile

Titanium

0.76 mm

10

10100

Sheehy Collar Button

Sterile

Titanium

1.0 mm

10

10100-F

Sheehy Collar Button

Sterile

Titanium

1.0 mm

10

10125

Sheehy Collar Button

Sterile

Titanium

1.25 mm

10

10125-F

Sheehy Collar Button

Sterile

Titanium

1.25 mm

10

10150

Sheehy Collar Button

Sterile

Titanium

1.50mm

10

10150-F

Sheehy Collar Button

Sterile

Titanium

1.50mm

10

23-40300

Sheehy Collar Button

Sterile

FLPL

1.27mm

10

23-40300B

Sheehy Collar Button - Blue

Sterile

FLPL

1.27mm

10

23-40301

Sheehy Collar Button with wire

Sterile

FLPL

1.27mm

10

23-50300

Sheehy Collar Button

Sterile

Silicone

1.27mm

10

SHEPARD STYLE GROMMET
Number

Description

Material

ID

23-40100-S

Shepard Grommet

Sterile

FLPL

1.14 mm

Qty/Box
10

23-40100-SB

Shepard Grommet - Blue

Sterile

FLPL

1.14 mm

10

23-40101-S

Shepard Grommet with wire

Sterile

FLPL

1.14 mm

10

23-40101-SB

Shepard Grommet with wire - Blue

Sterile

FLPL

1.14 mm

10

101100

Shepard Grommet

Sterile

Titanium

1.0 mm

10

101100-F

Shepard Grommet with wire

Sterile

Titanium

1.0 mm

10

101125

Shepard Grommet

Sterile

Titanium

1.25 mm

10

101125-F

Shepard Grommet with wire

Sterile

Titanium

1.25 mm

10

23-40120

Shepard Grommet

Sterile

FLPL

1.02 mm

10

23-40121

Shepard Grommet with wire

Sterile

FLPL

1.02 mm

10

33

Ventilation tubes

SPOON BOBBIN STYLE
Number

Description

23-60500

Spoon Bobbin

Sterile

Material

ID

Titanium

1.14 mm

Qty/Box
10

STRAIGHT SHANK VENT TUBE
Number
ID

Description

Material

ID

Length

Qty/Box

12 mm

10

23-41100

Straight Shank Vent Tube

Sterile

FLPL

.089
mm

23-41110

Straight Shank Vent Tube

Sterile

FLPL

1.14
mm

12 mm

10

23-41120

Straight Shank Vent Tube

Sterile

FLPL

.089
mm

7 mm

10

23-41130

Straight Shank Vent Tube

Sterile

FLPL

1.14
mm

7 mm

10

OTO ACC

Length

T-TUBES

12mm

6mm

ID
A

B

34

Number

Description

Material

ID

23-50600

T-Tube

Sterile

Silicone

1.14 mm

Qty/Box
10

23-50601

T-Tube Modified

Sterile

Silicone

1.32 mm

10

23-50610

T-Grommet

Sterile

Silicone

1.14 mm

10

Material

ID

Silicone

1.27 mm

ULTRA VENT
Number

Description

23-50900

A=1.37 mm, B=4.5 mm

Sterile

Qty/Box
10

Otovent®

OTOVENT® MIDDLE EAR AUTO INFLATION SYSTEM
The proven alternative to the surgical treatment of symptoms of Otitis Media and Eustachian Tube Dysfunction.
Used around the world, for more than 18 years, the Otovent Middle Ear Auto Inflation System offers
Otitis Media Patients and those suffering from Barotrauma a proven protocol to equalize middle ear
pressure and relieve painful symptoms. The Valsalva and Politzer treatments have long been used to
equalize middle ear pressure in the presence of negative pressure pain of Otitis Media, Barotrauma due
to underwater pressure, air flight, or hyperbaric chamber treatments.

OTO ACC

BENEFITS OF OTOVENT
Otovent can prevent or treat Otitis Media and be an attractive alternative to surgery. Otovent treats
many of the complications associated with negative ear pressure caused by Eustachian tube dysfunction.
•
•
•
•
•

Frequent treatments are painless and regarded as “fun” by children
Typically satisfying results early on; compliance is very high
Effective without drugs and with no known side effects
May avoid or delay recourse to surgery or ventilation tubes
Very low treatment cost

HOW TO USE OTOVENT®
Otovent® is simple to use. With one nostril pinched shut, and the balloon mounted nose plug held against the other nostrum, the patient inflates
the balloon. Once fully extended, the patient then allows the positive pressure of the balloon to reenter the nose, and swallows, achieving transEustachian tube middle ear insufflation.

BEFORE: Otitis Media, Eustachian tube dysfunction
Negative pressure, pain, impaired hearing, learning
problems.
DURING: Controlled pressure is transmitted through
the nose and Eustachian tube to the middle ear
pressure is balanced.
AFTER: Pain relief, hearing restored and improved
prognosis.

OTOVENT TREATMENT SET
The system consists of a nares bulb and an ample supply of latex balloons to perform safe and effective middle ear auto inflation, 2-3 times daily,
for up to 6 weeks.
Each Kit Contains: one nose piece made of PVC, one instruction leaflet, and 10 pressure tested latex balloons

Number

Description

90-00000

Otovent Kits, 1 Case*

12 patient kits

Qty/Box

90-00001

Otovent Kits, 1/2 Case*

6 patient kits

90-00000B

Otovent balloons*

5 per pack

The system consists of a nares bulb and an ample supply of latex balloons to perform safe and
effective middle ear auto inflation, 2-3 times daily, for up to 6 weeks.
* Contains latex

35

R&CS ACC

DIS

OTO ACC

OSSICULAR PROSTHESES

OSS
LAR ACC

SPE ACC

RHI INS

PSB

OTO INS

LAR INS

ORO/NAS INS

Incus
L = Total Length
FL = Functional Length

DENSE HA INCUS STRUT

TITANIUM INCUS STRUT
• Columella O.D.: 2.00 / Columella I.D.: 1.20

• Columella O.D.: 2.00

Number

Length (MM)

Number

Length (MM)

INCUS 07.17.275C

2.75

PAP 07.56.300

3.00

INCUS 07.17.325C

3.25

PAP 07.56.400

4.00

INCUS 07.17.375C

3.75

PAP 07.56.500

5.00

INCUS07.17.490C

4.90

DENSE HA PARTIAL INCUS ISJ

TITANIUM INCUS GRIP REPLACEMENT

Number

Dimensions

INCUS 07.32

L = 2.50 mm H= 1.60 mm

L

Number

Dimensions

PAP 07.53

Total length: 1.90 mm
Thickness: 0.05 mm

OSS

POROUS HA ADJUSTABLE PARTIAL WITH MALLEUS SLOT

DENSE HA AND PE INCUS REPLACEMENT WITH MALLEABLE
HEAD

• Platinum wire
• Columella O.D.: 2.10

L

Number

(MM)

Number

L

(MM)

PAP 07.34.400

4.00

PAP 07.34.550

5.50

PAP 07.34.450

4.50

PAP 07.34.600

6.00

PAP 07.34.500

5.00

POROUS HA HEAD WITH MALLEUS SLOT, PTFE SHAFT

Number

Dimensions

PAP 07.43

Total Length (L): 6.50 mm
Head: 3.50
Platinum wire O.D.: 0.25
Columella external O.D.: 2.20

POROUS HA AND PE ADJUSTABLE PARTIAL WITH MALLEUS SLOT

Number

Dimensions

Number

Dimensions

PAP 07.36

Total Length (L): 6.50 to 3.00 mm
Head O.D.: 3.50 mm
Platinum Wire O.D.: 0.25 mm
PTFE Columella O.D.: 2.10 mm

PAP 07.38

Total Length (L): 6.50 to 3.00 mm
Head O.D.: 3.50 mm
Platinum Wire O.D.: 0.25 mm
Audio-PE Columella O.D.: 2.10 mm

POROUS HA / PTFE / TITANIUM UNIVERSAL TOTAL/PARTIAL WITH
MALLEUS HOOK
• Columella inside O.D.: 1.10

Number

Dimensions

TPL 07.59

Partial: Minimum Length: 3.50
Columella outside O.D.: 1.30
Total: Maximum length: 7.50
Columella O.D.: 0.60

39

Incus
L = Total Length
FL = Functional Length

POROUS HA / TITANIUM INCUS WITH MALLEUS SLOT

POROUS HA / TITANIUM EXTENSIBLE INCUS WITH MALLEUS SLOT

• Columella O.D.: 1.30 / Columella I.D.: 1.10

Number

L (MM) Number

PAP 07.66.175

1.75

• Extendable Stem

L (MM)

PAP 07.66.325 3.25

PAP 07.66.200

2.00

PAP 07.66.350 3.50

PAP 07.66.225

2.25

PAP 07.66.400 4.00

PAP 07.66.250

2.50

PAP 07.66.450 4.50

PAP 07.66.275

2.75

PAP 07.66.500 5.00

PAP 07.66.300

3.00

POROUS HA / TITANIUM INCUS WITH MALLEUS SLOT

OSS

• Columella O.D.: 1.30 / Columella I.D.: 1.10

40

Number

Extended
L (MM)

Compressed
L (MM)

PAP 07.60.250

2.50

1.80

PAP 07.60.300

3.00

2.30

PAP 07.60.350

3.50

2.80

PAP 07.60.400

4.00

3.30

PAP 07.60.450

4.50

3.80

PAP 07.60.500

5.00

4.30

Number

Dimensions

PAP 07.68

Total Length (L): 2.50 to 5.00
mm
Head size: 3.50 x 2.50 mm

POROUS HA / TITANIUM REPLACEMENT INCUS WITH MALLEUS
SLOT
• Extendable Stem

Number

Length

PAP 07.72

2.0 to 5.0 mm

Incus-Stapes
L = Total Length
FL = Functional Length

DENSE HA I-S “MARPLA” BY E. GARCIA IBANEZ - WEHRS TYPE

TITANIUM/PTFE TRIMMABLE INCUS STAPES
Number
TAP 07.52

Dimensions

Number

Dimensions

Total Length: 6.25 to 4.50 mm
Titanium F67 Gr.2
Thickness: 0.05 mm
PTFE O.D.: 0.60 mm

TAP 07.54

Total Length: 8.00 mm
Head: 4.00 mm
Columella width: 1.00 x 0.80
mm

POROUS HA AND PE MALLEABLE I-S WITH MALLEUS SLOT

DENSE HA AND PE I-S PROSTHESIS WITH MALLEABLE HEAD
Dimensions

Number

Dimensions

TAP 07.42

Total Length: 8.00 mm
Head: 3.50 mm
Platinum Wire O.D.: 0.20
Audio-PE O.D.: 0.75

TAP 07.37

Total Length (L): 8.00 to 3.25
mm
Head O.D.: 3.50 mm
Platinum Wire O.D.: 0.20 mm
Audio-PE Columella O.D.: 060
mm

POROUS HA AND PTFE MALLEABLE INCUS STAPES WITH
MALLEUS SLOT
• Platinum wire

Number

Dimensions

TAP 07.35

Total Length (L): 8.00 to 3.25 mm
Head O.D.: 3.50 mm
Platinum Wire O.D.: 0.20 mm
Audio-PE Columella O.D.: 0.60
mm

TITANIUM / POROUS HA ADJUSTABLE I-S WITH MALLEUS SLOT
• Extendable stem

OSS

Number

POROUS AND DENSE HA MALLEABLE I-S
• Platinum wire
• Lower End Columella O.D.: 0.65

Number

Length (mm)

TAP 07.33.550

5.50

TAP 07.33.600

6.00

TAP 07.33.650

6.50

TAP 07.33.700

7.00

TAP 07.33.750

7.50

TAP 07.33.800

8.00

TITANIUM / POROUS HA ADJUSTABLE I-S WITH MALLEUS HOOK
• Extendable stem

Number

Dimensions

Number

Dimensions

TAP 07.67

Total Length (L): 4.00 to 8.00 mm
Head size: 3.50 x 2.50 m

TAP 07.58

Total Length (L): 5.00 to 8.50
mm
Head size: 3.50 x 2.50 mm
Columella O.D.: 0.60 mm

TITANIUM / POROUS HA I-S WITH MALLEUS SLOT

TITANIUM / PTEF / HAP SPRING TOTAL

• Columella O.D.: 0.60

Number

L (MM) Number

L (MM)

TAP 07.65.300

3.00

5.00

TAP 07.65.500

TAP 07.65.325

3.25

TAP 07.65.525

5.25

TAP 07.65.350

3.50

TAP 07.65.550

5.50

TAP 07.65.375

3.75

TAP 07.65.600

6.00

TAP 07.65.400

4.00

TAP 07.65.650

6.50

TAP 07.65.425

4.25

TAP 07.65.700

7.00

TAP 07.65.450

4.50

TAP 07.65.750

7.50

TAP 07.65.475

4.75

TAP 07.65.800

8.00

• Wire O.D.: 0.20 mm
• PTFE O.D.: 0.6 mm

Number

Extended
L (MM)

Compressed
L (MM)

TAP 07.71

8.00 - 4.00

7.30 - 3.30

41

Partial
L = Total Length
FL = Functional Length

PE PARTIAL

PE OFFSET PARTIAL
Number

Dimensions

Number

Dimensions

PAP 07.10

Total Length (L): 5.00 mm
Columella O.D.: 2.10 mm

TPL 07.02

Total Length (L): 5.00 mm
Columella O.D.: 1.80 mm

HA OFFSET PARTIAL

DENSE HA PARTIAL

• Columella O.D.: 2.00
• Columella O.D.: 2.10

Number

Dimensions

PAP 07.12.300 3.00
PAP 07.12.350 3.50

OSS

PAP 07.12.400 4.00
PAP 07.12.450 4.50
PAP 07.12.500 5.00

DENSE HA 90° OVAL HEAD PARTIAL

Dimensions

TPL 07.06.300

3.00

TPL 07.06.350

3.50

TPL 07.06.400

4.00

TPL 07.06.450

4.50

TPL 07.06.500

5.00

DENSE HA 75° OVAL HEAD PARTIAL

• Columella O.D.: 2.00

• Columella O.D.: 2.00

Number

Length

Number

Length

PAP 07.15.300

3.00 mm

PAP 07.16.300

3.00 mm

PAP 07.15.350

3.50 mm

PAP 07.16.350

3.50 mm

PAP 07.15.400

4.00 mm

PAP 07.16.400

4.00 mm

PAP 07.15.450

4.50 mm

PAP 07.16.450

4.50 mm

PAP 07.15.500

5.00 mm

PAP 07.16.500

5.00 mm

DENSE HA MALLEABLE PARTIAL

DENSE HA AND PE PARTIAL WITH MALLEABLE HEAD

• Platinum wire
• Columella O.D.: 2.00

Number

L (MM) Number

L (MM)

TPL 07.08.350

3.50

TPL 07.08.500

5.00

TPL 07.08.400

4.00

TPL 07.08.550

5.50

TPL 07.08.450

4.50

TPL 07.08.600

6.00

PE PARTIAL WITH MALLEABLE GOLD HEAD
• Trimmable PE columella

Number
PAP 07.47

42

Number

Number

Dimensions

PAP 07.41

Total Length (L): 6.50 mm
Head: 3.50 mm
Platinum wire O.D.: 0.25 mm
Columella external O.D: 2.20
mm

GOLD AND PE PARTIAL WITH MALLEABLE HEAD
• Extendable stem

Dimensions

Number

Dimensions

Total Length (L): 6.50 to 2.75 mm
Gold Wire O.D.: 0.30 mm
Columella O.D.: 1.80 mm
Columella I.D.: 1.20 mm

PAP 07.49

Total Length (L): 2.75 to 6.50
mm
Head: 3.00 mm
Gold Wire O.D.: 0.30 mm
Columella O.D.: 1.80 mm
Columella I.D.: 1.20 mm

Partial
L = Total Length
FL = Functional Length

DENSE HA TELESCOPIC UNIVERSAL PARTIAL / TOTAL

TITANIUM PARTIAL

• Columella O.D.: 2.10

• Columella O.D.: 1.30 / Columella I.D.: 1.10

Number

Dimensions

PAP 07.19.350

3.50 min / 4.20 max

PAP 07.19.400

4.00 min / 4.70 max

PAP 07.19.450

4.50 min / 5.20 max

PAP 07.19.500

5.00 min / 5.70 max

PAP 07.19.550

5.50 min / 6.20 max

PAP 07.19.600

6.00 min / 6.70 max

Number

L (MM) Number

L (MM)

PAP 07.62.175 1.75

PAP 07.62.325

3.25

PAP 07.62.200 2.00

PAP 07.62.350

3.50

PAP 07.62.225 2.25

PAP 07.62.400

4.00

PAP 07.62.250 2.50

PAP 07.62.450

4.50

PAP 07.62.275 2.75

PAP 07.62.500

5.00

PAP 07.62.300 3.00

TITANIUM ADJUSTABLE PARTIAL

TITANIUM PARTIAL WITH SLITS IN BELL

• Extendable Stem

Dimensions

PAP 07.64

Total Length (L): 2.00 to 6.00
mm
Head size: 3.50 x 2.50 mm

TITANIUM PARTIAL OFFSET WITH MALLEUS GROOVE

Number

L (MM) Number

L (MM)

12705

0.50

12720

2.00

12710

1.00

12722

2.25

12712

1.25

12725

2.50

12715

1.50

12730

3.00

12717

1.75

12735

3.50

OSS

Number

TITANIUM PARTIAL

Number

L (MM) Number

L (MM)

Number

L (MM) Number

L (MM)

12805

0.50

12820

2.00

12905

0.50

12920

2.00

12810

1.00

12822

2.25

12910

1.00

12922

2.25

12812

1.25

12825

2.50

12912

1.25

12925

2.50

12815

1.50

12830

3.00

12915

1.50

12830

3.00

12817

1.75

12835

3.50

12917

1.75

12835

3.50

TITANIUM ADJUSTABLE PARTIAL TRIMMABLE SHAFT
• Trimmable in 1 mm increments

Number

Dimensions

12100

5.50 to 2.50 mm

12200

5.00 to 2.00 mm

43

Total
L = Total Length
FL = Functional Length

PE TOTAL

PE OFFSET TOTAL
• Columella O.D.: 0.70

• Columella O.D.: 0.65

Length (MM)

Number

Length (MM)

TAP 07.09.600

6.00

TPL 07.04.600

6.00

TAP 07.09.700

7.00

TPL 07.04.700

7.00

8.00

TPL 07.04.800

8.00

Number

TAP 07.09.800

PE MALLEABLE OFFSET TOTAL

DENSE HA TOTAL
• Columella O.D.: 0.65

• Platinum core

Dimensions

Number

L (MM)

Number

L (MM)

TPL 07.03

Total Length (L): 8.00 mm
Columella O.D.: 0.70 mm

TAP 07.11.500

5.00

TAP 07.11.700

7.00

TAP 07.11.550

5.50

TAP 07.11.750

7.50

TAP 07.11.600

6.00

TAP 07.11.800

8.00

TAP 07.11.650

6.50

OSS

Number

DENSE HA OFFSET TOTAL

DENSE HA PARTIAL

• Columella O.D.: 0.70

Number

• Columella O.D.: 0.75

L (MM) Number

L (MM)

Number

L (MM) Number

L (MM)

TPL 07.05.500

5.00

TPL 07.05.700

7.00

TAP 07.13.500

5.00

TAP 07.13.700

7.00

TPL 07.05.550

5.50

TPL 07.05.750

7.50

TAP 07.13.550

5.50

TAP 07.13.750

7.50

TPL 07.05.600

6.00

TPL 07.05.800

8.00

TAP 07.13.600

6.00

TAP 07.13.800

8.00

TPL 07.05.650

6.50

TAP 07.13.650

6.50

DENSE HA 75° OVAL HEAD TOTAL

DENSE HA MALLEABLE TOTAL

• Columella O.D.: 0.70

Number

L (MM) Number

L (MM)

TAP 07.14.500

5.00

TAP 07.14.700

7.00

TAP 07.14.550

5.50

TAP 07.14.750

7.50

TAP 07.14.600

6.00

TAP 07.14.800

8.00

TAP 07.14.650

6.50

PTFE TOTAL WITH MALLEABLE GOLD HEAD AND SHAFT

• Platinum Wire
• Columella O.D.: 0.65

Number

L (MM) Number

L (MM)

TPL 07.07.550

5.50

TPL 07.07.700

7.00

TPL 07.07.600

6.00

TPL 07.07.750

7.50

TPL 07.07.650

6.50

TPL 07.07.800

8.00

DENSE HA AND PTFE MALLEABLE TOTAL

• Trimmable PTFE columella

44

Number

Dimensions

TAP 07.46

Total Length (L): 8.00 to 4.50 mm
Head: 3.00 mm
Gold wire O.D.: 0.30 mm
PTFE O.D.: 0.80 mm

Number Dimensions
TAP
07.40

Total Length (L): 8.00 mm
Head O.D.: 3.50 mm
Platinum Wire O.D.: 0.20 mm
Audio-PE Columella O.D.: 0.75
mm

Total
L = Total Length
FL = Functional Length

ADJUSTABLE TOTAL WITH GOLD HEAD AND SHAFT WITH PTFE
COLUMELLA

TITANIUM ADJUSTABLE TOTAL

• Extendable stem

• Extendable stem

Number

Dimensions

Number

Dimensions

TAP 07.48

Total Length (L): 4.00 to 9.00 mm
Head: 3.00 mm
Gold Wire O.D.: 0.30 mm
PTFE O.D.: 0.80 mm

TAP 07.55

Total Length (L): 5.00 to 8.50
mm
Head size: 3.80 x 3.00 mm

DENSE HA TELESCOPIC TOTAL TRIMMABLE

TITANIUM TOTAL
• Columella O.D.: 0.60

• Piston O.D.: 0.80

L (MM) Number

L (MM)

TAP 07.61.300

3.00

TAP 07.61.500

5.00

TAP 07.61.325

3.25

TAP 07.61.525

5.25

TAP 07.61.350

3.50

TAP 07.61.550

5.50

TAP 07.61.375

3.75

TAP 07.61.600

6.00

TAP 07.61.400

4.00

TAP 07.61.650

6.50

TAP 07.61.425

4.25

TAP 07.61.700

7.00

TAP 07.61.450

4.50

TAP 07.61.750

7.50

TAP 07.61.475

4.75

TAP 07.61.800

8.00

TITANIUM ADJUSTABLE TOTAL AND PARTIAL UNIVERSAL

Number

Dimensions (MM)

TAP 07.18.500

5.00 min / 5.70 max

TAP 07.18.550

5.50 min / 6.20 max

TAP 07.18.600

6.00 min / 6.70 max

TAP 07.18.650

6.50 min / 7.20 max

TAP 07.18.700

7.00 min / 7.70 max

TAP 07.18.750

7.50 min / 8.20 max

TAP 07.18.800

8.00 min / 8.70 max

OSS

Number

TITANIUM ADJUSTABLE TOTAL
• Extendable Stem

Number

Dimensions

TPL 07.57

Partial:
Minimum length: 3.50 mm
Columella O.D.: 1.80 mm
Columella I.D.: 1.20 mm

Number

Dimensions

TAP 07.63

Total Length (L): 3.00 to 8.00
mm
Head size: 3.50 x 2.50 mm

Total:
Maximum length: 8.50 mm
Columella O.D.: 0.70 mm

TITANIUM TRIMMABLE TOTAL WITH SEPARATE HEAD

TITANIUM TOTAL FIXED LENGTH WITH ADJUSTABLE CENTERED
HEAD

• Trimmable in 1 mm increments

Number

Dimensions

Number

L (MM) Number

L (MM)

11300

7.5 to 3.50 mm

11930*

3.00

11947

4.75

11400

7.0 to 3.00 mm

11935

3.50

11950

5.00

11940

4.00

11960

6.00

11942

4.25

11965

6.50

11945

4.50

11970

7.00

*Fixed head

TITANIUM TOTAL FIXED LENGTH WITH ADJUSTABLE OFFSET
HEAD

TITANIUM MALLEABLE TRIMMABLE TOTAL WITH ADJUSTABLE
HEAD AND SEPARATE SHOE
• Trimmable PTFE columella

• Trimmable PTFE columella

Number

Dimensions

11500

7.50 to 2.80 mm

11600

7.30 to 2.30 mm

*Fixed head

Number

L (MM) Number

L (MM)

11830*

3.00

11847

4.75

11835

3.50

11850

5.00

11840

4.00

11860

6.00

11842

4.25

11865

6.50

11845

4.50

11870

7.00

45

Serenocem™ Otologic Cement

SERENOCEM™ OTOLOGIC CEMENT

Designed specifically for non-weight bearing applications in otologic surgery such as:
• Ideal for bridging an open incudostapedial joint
• Reconstruction of the ossicular chain
• Posterior canal wall reconstruction
• Cementation of cochlear implant electrode array
SerenoCem™ meets a clinical need in otologic reconstruction surgery, where
increasingly sophisticated surgical techniques require new methods of stabilizing
implanted devices and bony fragments and for use in the reconstruction.

OSS

•
•
•
•
•
Open ISJ

Non-exothermic snap set
Chemical adhesion to bone and metals
Bioactive/osteoconductive ion release
Minimal biodegeneration or absorption
Minimal shrinkage upon setting

BIOCOMPATIBILITY/CLINICAL DATA
Cement rapidly becomes surrounded by a layer of relatively mature bone.
Tests conducted with completely hardened cement show a distinct inertia and
biocompatibility of the material including its complete integration into the bone
structure.
INTERACTION MRI
Serenocem™ is MRI-compatible. Image quality may be impeded in direct vicinity of an
implant; radiopacity is comparable to bone.

Closed bridge using Serenocem™
(Bridging the open ISJ)

Note: The area into which the cement is placed must be kept dry, as the material will not harden in a wet
field.

Number

Description

Qty/box

BC-010

Serenocem™ Cement

2 individually packaged capsules

BC-010S

Serenocem™ Cement

1 individually packaged capsule

SERENOCEM™ APPLICATOR AND MIXER

These critical components are supplied to provide predictable and timely formulation
of SerenoCem Otologic Cement, within the time window expected.
Serenocem™ Mixer
Set to operate for 10 seconds, every time, giving the OR team confidence in the
Cement, its set up time and its consistency, instillation after instillation.
Serenocem™ Applicator
Used to place the prepared aliquot of cement onto a sterile microscope slide or cutting
block, to be added to the surgical field on a Rosen Needle or Micro suction tip.

46

Number

Description

Qty/box

BC-280

Serenocem™ Mixer (110 V)

1 Unit

BC-150

Applicator

1 each

Canal Wall
L = Total Length
FL = Functional Length

DENSE HA POSTERIOR CANAL WALL
A

A

Number
B

B

A

Left

B

Left

Right

A

Description
Width (A): 20 mm
Length (B): 22 mm
Outside Radius: 10 mm
Inside Radius: 6 mm

TPL 07.39L

Left

TPL 07.39R

Right

B

Right

OSS

Caps and Shoe

DENSE HA FOOTPLATE SHOE

DENSE HA PROSTHESIS “MARPLA” BY E. GARCIA IBANEZ

Number

Dimensions

Number

Dimensions

TPL 07.44

Footplate size 2.00 x 1.20 mm
Inner O.D.: 0.80 mm
Added implant length: 0.50 mm

TPL 07.45

Total Length (L): 1 - 3.50 mm
Total Drilled Head: 4.00 mm
Inside O.D.: 1.40 mm

Number

Dimensions

PAP 07.50

Total Length (L): 1.00 - 4.00 mm
Columella external O.D.: 2.10 mm
Columella I.D.: 1.20 mm

POROUS HA CAP

47

Stapes
L = Total Length
FL = Functional Length

PLATINUM AND PTFE PROSTHESES FOR STAPEDECTOMY AND STAPEDOTOMY

FL /

OSS

FL

L

Piston O.D.: 0.40

Piston O.D.: 0.50

Piston O.D.: 0.60

Piston O.D.: 0.80

Number

Number

Number

Number

3.00

/

4.00

SPL 03.08.400

SPL 03.09.400

SPL 03.07.400

SPL 03.10.400

3.25

/

4.25

SPL 03.08.425

SPL 03.09.425

SPL 03.07.425

SPL 03.10.425

3.50

/

4.50

SPL 03.08.450

SPL 03.09.450

SPL 03.07.450

SPL 03.10.450

3.75

/

4.75

SPL 03.08.475

SPL 03.09.475

SPL 03.07.475

SPL 03.10.475

4.00

/

5.00

SPL 03.08.500

SPL 03.09.500

SPL 03.07.500

SPL 03.10.500

4.25

/

5.25

SPL 03.08.525

SPL 03.09.525

SPL 03.07.525

SPL 03.10.525

4.50

/

5.50

SPL 03.08.550

SPL 03.09.550

SPL 03.07.550

SPL 03.10.550

4.75

/

5.75

SPL 03.08.575

SPL 03.09.575

SPL 03.07.575

SPL 03.10.575

5.00

/

6.00

SPL 03.08.600

SPL 03.09.600

SPL 03.07.600

SPL 03.10.600

5.25

/

6.25

SPL 03.08.625

SPL 03.09.625

SPL 03.07.625

SPL 03.10.625

5.50

/

6.50

SPL 03.08.650

SPL 03.09.650

SPL 03.07.650

SPL 03.10.650

8.99

/

9.99

SPL 03.08.999

SPL 03.09.999

SPL 03.07.999

SPL 03.10.999

Piston O.D.: 0.40

Piston O.D.: 0.50

Piston O.D.: 0.60

Piston O.D.: 0.80

Number

Number

Number

Number

TITANIUM PROSTHESES FOR STAPEDECTOMY AND STAPEDOTOMY

FL /

FL

L

3.00

/

4.00

SPL 03.21.400

SPL 03.22.400

SPL 03.20.400

SPL 03.23.400

3.25

/

4.25

SPL 03.21.425

SPL 03.22.425

SPL 03.20.425

SPL 03.23.425

3.50

/

4.50

SPL 03.21.450

SPL 03.22.450

SPL 03.20.450

SPL 03.23.450

3.75

/

4.75

SPL 03.21.475

SPL 03.22.475

SPL 03.20.475

SPL 03.23.475

4.00

/

5.00

SPL 03.21.500

SPL 03.22.500

SPL 03.20.500

SPL 03.23.500

4.25

/

5.25

SPL 03.21.525

SPL 03.22.525

SPL 03.20.525

SPL 03.23.525

4.50

/

5.50

SPL 03.21.550

SPL 03.22.550

SPL 03.20.550

SPL 03.23.550

4.75

/

5.75

SPL 03.21.575

SPL 03.22.575

SPL 03.20.575

SPL 03.23.575

5.00

/

6.00

SPL 03.21.600

SPL 03.22.600

SPL 03.20.600

SPL 03.23.600

5.25

/

6.25

SPL 03.21.625

SPL 03.22.625

SPL 03.20.625

SPL 03.23.625

5.50

/

6.50

SPL 03.21.650

SPL 03.22.650

SPL 03.20.650

SPL 03.23.650

8.99 /

9.99

SPL 03.21.999

SPL 03.22.999

SPL 03.20.999

SPL 03.23.999

TRIMMABLE PLATINUM AND PTFE PROSTHESES FOR STAPEDECTOMY AND STAPEDOTOMY

FL /

L

6.0 - 3.25 / 7.00 - 4.25

Piston O.D.: 0.40

Piston O.D.: 0.50

Piston O.D.: 0.60

Piston O.D.: 0.80

Number

Number

Number

Number

SPL 03.08S

SPL 03.09S

SPL 03.07S

SPL 03.10S

FL

TRIMMABLE TITANIUM AND PTFE FOR STAPEDECTOMY AND STAPEDOTOMY

FL /

L

6.0 - 3.25 / 7.00 - 4.25
FL

48

Piston O.D.: 0.40

Piston O.D.: 0.50

Piston O.D.: 0.60

Piston O.D.: 0.80

Number

Number

Number

Number

SPL 03.27S

SPL 03.28S

SPL 03.29S

SPL 03.30S

Stapes
L = Total Length
FL = Functional Length

PTFE LOOP PROSTHESIS WITH NOTCH FOR STAPEDECTOMY AND
STAPEDOTOMY - TRIMMABLE

FL

Number

FL (MM)

L (MM)

Piston Ø

Number

FL (MM)

L (MM)

Piston Ø

SPL 03.16

3.00-6.00

4.00-7.00

0.50

SPL 03.05

5.00

6.0

0.30

SPL 03.17

3.00-6.00

4.00-7.00

0.60

SPL 03.18

3.00-6.00

4.00-7.00

0.40

SPL 03.19

3.00-6.00

4.00-7.00

0.80

PTFE LOOP PROSTHESIS WITHOUT NOTCH FOR
STAPEDECTOMY AND STAPEDOTOMY - TRIMMABLE

FL

Number

FL (MM)

L (MM)

Piston Ø

SPL 03.16x

3.00-6.00

4.00-7.00

0.50

Number

FL (MM)

L (MM)

Piston Ø

3.00-6.00

4.00-7.00

0.60

24-0450

4.00

5.00

0.40

3.00-6.00

4.00-7.00

0.40

24-0640

3.00

4.00

0.60

SPL 03.19x

3.00-6.00

4.00-7.00

0.80

24-0645

3.50

4.50

0.60

24-0650

4.00

5.00

0.60

24-0660

5.00

6.00

0.60

HOUSE TYPE PLATINUM LOOPED FOR STAPEDECTOMY
PROSTHESIS
• Platinum loop O.D.: 0.40

Number

FL (MM)

L (MM)

Piston Ø

SPL 03.24

3.00-6.00

4.00-7.00

0.40

SPL 03.25

3.00-6.00

4.00-7.00

0.50

SPL 03.26

3.00-6.00

4.00-7.00

0.60

Number

FL

OSS

SPL 03.17x

Number
FL

FL (MM)

L (MM)

SPL 03.15.400

3.00

4.00

SPL 03.15.450

3.50

4.50

SPL 03.15.500

4.00

5.00

PLATINUM RIBBON LOOP AND SHAFT FOR STAPEDECTOMY
PROSTHESIS

PLATINUM AND PE PROSTHESIS FOR STAPEDECTOMY

FL (MM)

L (MM)

SPL 03.04.300

2.00

3.00

SPL 03.04.350

2.50

3.50

SPL 03.04.400

3.00

4.00

SPL 03.04.425

3.25

4.25

SPL 03.04.450

3.50

SPL 03.04.475

3.75

SPL 03.04.500
SPL 03.04.550
SPL 03.04.600

FL (MM)

L (MM)

SPL 03.00.300

2.00

3.00

SPL 03.00.350

2.50

3.50

SPL 03.00.400

3.00

4.00

SPL 03.00.425

3.25

4.25

4.50

SPL 03.00.450

3.50

4.50

4.75

SPL 03.00.475

3.75

4.75

4.00

5.00

SPL 03.00.500

4.00

5.00

4.50

5.50

SPL 03.00.550

4.50

5.50

5.00

6.00

SPL 03.00.600

5.00

6.00

Number

FL

HOUSE TYPE PLATINUM LOOPED STAPEDECTOMY PROSTHESIS
WITH BALL BASE

TRIMMABLE TITANIUM / PTFE SELF CRIMPING PROSTHESIS

FL

• Sterile
• Expand Loop with pick and slip over incus

SPL 03.18x

• Silicon loop
• TI joint
• PTFE columella

FL

FL

PTFE LOOP PROSTHESIS WITHOUT NOTCH FOR STAPEDECTOMY
AND STAPEDOTOMY - FIXED

SULTAN LOOP PISTON PROSTHESIS FOR STAPEDECTOMY AND
STAPEDOTOMY

FL

PLATINUM PROSTHESIS FOR STAPEDECTOMY

Number

FL (MM)

L (MM)

Piston Ø

SPL 03.35S

6.00-3.25

7.00-4.25

0.40

SPL 03.36S

6.00-3.25

7.00-4.25

0.50

SPL 03.37S

6.00-3.25

7.00-4.25

0.60

SPL 03.38S

6.00-3.25

7.00-4.25

0.80

• Platinum sphere O.D.: 0.40

Number

FL

FL (MM)

L (MM)

SPL 03.13.400

3.00

4.00

SPL 03.13.450

3.50

4.50

SPL 03.13.500

4.00

5.00

49

Bucket Handles
L = Total Length
FL = Functional Length

TITANIUM BUCKET HANDLE

FL /

FL

O.D.: 1.10
I.D.: 0.95

Piston O.D.: 0.40

Piston O.D.: 0.50

Piston O.D.: 0.60

Piston O.D.: 0.80

L

Number

Number

Number

Number

SPL 03.48.400

SPL 03.51.400

SPL 03.49.400

SPL 03.50.400

3.20

/

4.00

3.45

/

4.25

SPL 03.48.425

SPL 03.51.425

SPL 03.49.425

SPL 03.50.425

3.70

/

4.50

SPL 03.48.450

SPL 03.51.450

SPL 03.49.450

SPL 03.50.450

3.95

/

4.75

SLP 03.48.475

SPL 03.51.475

SLP 03.49.475

SLP 03.50.475

4.20

/

5.00

SPL 03.48.500

SPL 03.51.500

SPL 03.49.500

SPL 03.50.500

4.45

/

5.25

SPL 03.48.525

SPL 03.51.525

SPL 03.49.525

SPL 03.50.525

4.70

/

5.50

SPL 03.48.550

SPL 03.51.550

SPL 03.49.550

SPL 03.50.550

4.95

/

5.75

SPL 03.48.575

SPL 03.51.575

SPL 03.49.575

SPL 03.50.575

5.20

/

6.00

SPL 03.48.600

SPL 03.51.600

SPL 03.49.600

SPL 03.50.600

5.45

/

6.25

SPL 03.48.625

SPL 03.51.625

SPL 03.49.625

SPL 03.50.625

5.70

/

6.50

SPL 03.48.650

SPL 03.51.650

SPL 03.49.650

SPL 03.50.650

5.95

/

6.75

SPL 03.48.675

SPL 03.51.675

SPL 03.49.675

SPL 03.50.675

6.20 /

7.00

SPL 03.48.700

SPL 03.51.700

SPL 03.49.700

SPL 03.50.700

6.45

/

7.25

SPL 03.48.725

SPL 03.51.725

SPL 03.49.725

SPL 03.50.725

6.70

/

7.50

SPL 03.48.750

SPL 03.51.750

SPL 03.49.750

SPL 03.50.750

PTFE/AUDIOLITE ADJUSTABLE CUP PROSTHESIS FOR
STAPEDECTOMY
• Porous HA
• AUDIOLITE - cup
• PT - joint
• PTFE - columella

L

50

Number

Dimensions

SPL 03.14

L: 6.00 mm
Cup O.D.: 2.00 mm
Cup I.D.: 1.20 mm
Columella O.D.: 0.60 mm

Nitinol Stapes
L = Total Length
FL = Functional Length

SUPERE STAPES REPLACEMENT TECHNIQUE
The Invotec SuperE Stapes replacement Piston utilizes state of
the art, shape-memory superelastic Nitinol alloy as its piston
loop, to take the crimping maneuver out of Stapedectomy and
Stapedotomy.
The SuperE Nitinol piston ribbon loop comes programmed in the
closed position, to which it will return, once placed onto the incus.
Using the E-gator alligator forceps to grasp, open the piston loop,
and to place the implant onto the incus, the surgeon completes the
maneuver in one concise motion. The Superelastic Nitinol piston
loop gently and securely, closes, fashioning itself around the incus.
Two micro-slots in the distal end of the alligator jaws secure the
piston loop during implantation and, while closed, open the piston
loop for easy and safe placement.

DIRECTIONS FOR USE
1. Utilizing the E-Gator, grasp the SuperE Nitinol Piston loop (as shown),
capturing the ribbon within the micro-grooves.
2. When ready to place the implant onto the incus, exert additional
closure pressure on the jaws, this will spread the loop.
3. Place the Nitinol piston onto the incus and into the oval window as
desired. Opening the alligator jaws releases the implant and allows
the loop to self-crimp.
4. The piston loop will close to its programmed, closed position securing
the implant onto the incus.

51

Nitinol Stapes
L = Total Length
FL = Functional Length

SELF-CRIMPING SUPERELASTIC NITINOL/PTFE PISTON

FL /

OSS

FL

L

Columella O.D.: 0.40

Columella O.D.: 0.50

Columella O.D.: 0.60

Columella O.D.: 0.80

Number

Number

Number

Number

3.00

/

4.00

SPL 03.43.400

SPL 03.44.400

SPL 03.45.400

SPL 03.46.400

3.25

/

4.25

SPL 03.43.425

SPL 03.44.425

SPL 03.45.425

SPL 03.46.425

3.50

/

4.50

SPL 03.43.450

SPL 03.44.450

SPL 03.45.450

SPL 03.46.450

3.75

/

4.75

SPL 03.43.475

SPL 03.44.475

SPL 03.45.475

SPL 03.46.475

4.00

/

5.00

SPL 03.43.500

SPL 03.44.500

SPL 03.45.500

SPL 03.46.500

4.25

/

5.25

SPL 03.43.525

SPL 03.44.525

SPL 03.45.525

SPL 03.46.525

4.50

/

5.50

SPL 03.43.550

SPL 03.44.550

SPL 03.45.550

SPL 03.46.550

4.75

/

5.75

SPL 03.43.575

SPL 03.44.575

SPL 03.45.575

SPL 03.46.575

5.00

/

6.00

SPL 03.43.600

SPL 03.44.600

SPL 03.45.600

SPL 03.46.600

5.50

/

6.50

SPL 03.43.650

SPL 03.44.650

SPL 03.45.650

SPL 03.46.650

6.00

/

7.00

SPL 03.43.700

SPL 03.44.700

SPL 03.45.700

SPL 03.46.700

6.50

/

7.50

SPL 03.43.750

SPL 03.44.750

SPL 03.45.750

SPL 03.46.750

7.00

/

8.00

SPL 03.43.800

SPL 03.44.800

SPL 03.45.800

SPL 03.46.800

7.50

/

8.50

SPL 03.43.850

SPL 03.44.850

SPL 03.45.850

SPL 03.46.850

8.00

/

9.00

SPL 03.43.900

SPL 03.44.900

SPL 03.45.900

SPL 03.46.900

8.50

/

9.50

SPL 03.43.950

SPL 03.44.950

SPL 03.45.950

SPL 03.46.950

8.99

/

9.99

SPL 03.43.999

SPL 03.44.999

SPL 03.45.999

SPL 03.46.999

Columella O.D.: 0.40

Columella O.D.: 0.50

Columella O.D.: 0.60

Columella O.D.: 0.80

Number

Number

Number

Number

SPL 03.43S

SPL 03.44S

SPL 03.45S

SPL 03.46S

SELF-CRIMPING TRIMMABLE SUPERELASTIC NITINOL PISTON

FL /

L

6.0-6.25 / 7.00-4.25
FL

E-GATOR ALLIGATOR FORCEPS

52

Number

Description

SPL 03.01

E-Gator, alligator forceps, 4.0x0.9mm jaws, w/micro-slots.
Stainless steel, length: 70cm, 2 ¾”.

Instrumentation
L = Total Length
FL = Functional Length

BASIC BLOCK FOR THE TOTAL AND PARTIAL IMPLANT
SHORTENING SCALES

SHORTENING SCALES FOR USE WITH THE BASIC BLOCK FOR
TOTAL IMPLANTS WITH FIXED HEAD

Number

Dimensions

Number

Dimensions

PF001-10

Shortening Block

PF001-11

Tower for Fixed Head (Total)

SHORTENING SCALES FOR USE WITH THE BASIC BLOCK FOR
PARTIAL IMPLANTS

SHORTENING SCALES FOR USE WITH THE BASIC BLOCK FOR
TOTAL IMPLANTS WITH FIXED SHOE

Number

Dimensions

Number

Dimensions

PF001-12

Tower for Partial

PF001-13

Tower for Fixed Shoe (Total)

OSS

HILDMANN CARTILAGE HOLDING AND CUTTING FORCEPS

MEASURING GAUGE
Number

Dimensions

Number

Dimensions

02.14

Measuring Instrument

O10-50410

Straight, 10 CM, Stainless with
set screw

53

Trials
L = Total Length
FL = Functional Length

TRIALS FOR TITANIUM TOTAL IMPLANTS

TRIALS FOR TITANIUM PARTIAL IMPLANTS

• Stainless steel

Number

5.0

• Stainless steel

L (MM) Number

L (MM)

3.0

OSS

L (MM) Number

L (MM)

11000-D20

2.0

11000-D50

5.0

12000-D05

0.5

12000-D30

3.0

11000-D25

2.5

11000-D55

5.5

12000-D10

1.0

12000-D35

3.5

11000-D30

3.0

11000-D60

6.0

12000-D15

1.5

12000-D40

4.0

11000-D35

3.5

11000-D65

6.5

12000-D17

1.75

12000-D45

4.5

11000-D40

4.0

11000-D70

7.0

12000-D20

2.0

12000-D50

5.0

11000-D45

4.5

11000-D75

7.5

12000-D25

2.5

12000-D55

5.5

*** NOT FOR IMPLANTATION • REUSABLE ***

54

Number

Accessories
L = Total Length
FL = Functional Length

HOUSE STYLE CUTTING BLOCK

GELFOAM PRESS

• 2.87” x 1.5” x 9.0 mm
• Non-Sterile

• Stainless, 18 cm

Number

Dimensions

O64500

Platform 11x14 mm

O64501

Platform 30x30 mm

O64502

Platform 22x30 mm

Number

Dimensions

O99131

White Delrin

O99131B

Black Delrin

PHENOL APPLICATOR
• Duberstein Type

Dimensions

O99610

Round handle, Stainless, Matt,
Length 15.7 cm
Tynes : 0.63 mm x 1.57 mm

OSS

Number

55

R&CS ACC

DIS

OTO ACC

OSS

ACCESSORIES

LARYNGEAL

LAR ACC
SPE ACC

RHI INS

PSB

OTO INS

LAR INS

ORO/NAS INS

Tracheal T-Tube

Designed for the surgical management of tracheal and subglottic stenosis and the
reconstruction of cervical and thoracic trachea. Packaged 1 each.
A

• 100% medical grade silicone
• Easily trimmed to meet patient’s needs
• Large soft collar with closure attached

F

E

B

D

C

Number

Size

A

B

C

D

E

F

70-50080
70-50100

Standard

8 mm

37 mm

16.5 mm

32 mm

6.5 mm

14 mm

Standard

10 mm

50 mm

24 mm

42 mm

8 mm

18 mm

70-50120

Standard

12 mm

66 mm

32 mm

50 mm

10.5 mm

23 mm

70-50140

Standard

14 mm

71 mm

34 mm

50 mm

10.5 mm

26 mm

70-50160

Standard

16 mm

72 mm

34 mm

60 mm

11.5 mm

26 mm

70-50081

Long

8 mm

80 mm

60 mm

32 mm

6.5 mm

14 mm

70-50101

Long

10 mm

96 mm

70 mm

42 mm

8 mm

18 mm

70-50121

Long

12 mm

108 mm

75 mm

50 mm

10.5 mm

23 mm

70-50141

Long

14 mm

112 mm

75 mm

50 mm

10.5 mm

26 mm

70-50161

Long

16 mm

122 mm

85 mm

60 mm

11.5 mm

26 mm

LAR ACC

Disposable Adenoid Curettes
BECKMANN ADENOID CURETTE

• Sterile
• Single-use
• Sharp cutting edge for each case

25-2110

25-2120
Number

25-2130

25-2140

Description

Length

Size

Head
Width

Qty/
Box

25-2110

Adenoid Curette

Straight

22 cm

1

10 mm

5

25-2120

Adenoid Curette

Straight

22 cm

2

12 mm

5

25-2130

Adenoid Curette

Straight

22 cm

3

14 mm

5

25-2140

Adenoid Curette

Straight

22 cm

4

16 mm

5

59

Surface Electrodes

• Single use - Sterile

ET Tube

Qty/
Box

Single channel surface electrode Standard

7.5 - 10 mm

5

Wrap
Single channel surface electrode
around

7.5 - 10 mm

5

6.0 - 7.5 mm

5

Tip O.D.

Effective
Length

Qty/
Box

0.8 mm

80-120 mm

10

Number

Size

29-80500S
29-80500W

29-80500DC Dual Channel Electrode

Number

Size

29-3001

Disposable monopolar direct
nerve stimulator probe

Standard

R&CS ACC

DIS

OTO ACC

OSS

LAR ACC

SPECIALTY PRODUCTS
ACCESSORIES

SPE ACC

RHI INS

PSB

OTO INS

LAR INS

ORO/NAS INS

Personal Lighting Systems

BRIGHTSTAR™ HIGH POWER WIRELESS LED HEADLIGHT SYSTEM

• Focusable, battery powered, bright, white LED
Light Spot Distance Spot Ø
• Ultra comfortable, adjustable black head band
20-30 cm
38-55 mm
• Dual long lasting, rechargeable lithium ion batteries
40 cm
53-85 mm
(7 hours continuous)
50 cm

68-110 mm

60 cm

80-135 mm

Number

Description

34-4800

BrightStar™ High Power wireless LED Headlight System
Includes: Wireless LED headlight with removable dual battery packs,
charging station, black headband

34-4701

Lithium Ion battery pack replacement for 34-4800

34-4803

Dual Charging Station replacement

BRIGHTSTAR™ ULTRA WIRELESS LED HEADLIGHT SYSTEM

• Focusable, battery powered, bright, white LED
• Ultra comfortable, adjustable black head band
• Long lasting, rechargeable lithium ion battery
(3-5 hours continuous)

Light Spot Distance Spot Ø
20 cm

11-40 mm

30 cm

13-63 mm

40 cm

25-130 mm

Description

34-4700

BrightStar™ Ultra wireless LED Headlight System
Includes: Wireless LED headlight, removable battery pack, charger 110220v, black headband

34-4701

Lithium Ion battery pack replacement for 34-4700

34-4702

Charger 110/220 VAC replacement for 34-4700

34-4703

Charging Station

SPE ACC

Number

BRIGHTSTAR™ II LED HEADLIGHT SYSTEM

• Focusable, battery powered, bright, white LED
• Ultra comfortable, adjustable black head band
Light Spot Distance Spot Ø
• Dual long lasting, rechargeable lithium ion batteries
20 cm
11-40 mm
(5 hours continuous)
30 cm

13-63 mm

40 cm

25-130 mm

Number

Description

34-4190

BrightStar™ II LED headlight, lithium ion battery, charger 110-220v,
black headband

34-4191

Lithium Ion battery pack replacement with belt clip

34-4192

Charger for 34-4190

BRIGHTSTAR™ II WIRELESS LED HEADLIGHT SYSTEM

• Focusable, battery powered, bright, white LED
• Ultra comfortable, adjustable black head band
• Long lasting, rechargeable lithium ion battery
(3-5 hours continuous)

Light Spot Distance Spot Ø
20 cm

11-40 mm

30 cm

13-63 mm

40 cm

25-130 mm

Number

Description

34-4300

BrightStar™ Ultra wireless LED Headlight, headband mounted lithium
ion battery, charger 110-220v, complete, black headband

34-4301

Lithium Ion battery pack replacement for 34-4300

34-4302

Charger 110/220 VAC for 34-4300

63

Personal Lighting Systems

IFO FIBEROPTIC HEADLIGHT WITH OPEN HEADBAND

• Adjustable lightweight headband, F/O headlight,
bifurcated clear cable illumination for long term
balance, comfort and wear
• High performance optical system
• Wide focus range and powerful light spot

Light Spot Distance Spot Ø
20 cm

11-68 mm

30 cm

12-101 mm

40 cm

13-136 mm

50 cm

14-173 mm

60 cm

16-208 mm

Number

Description

34-4160

IFO Focusable Fiberoptic Headlight, open headband, bifurcated cable
illumination, black headband

IFO FIBEROPTIC HEADLIGHT WITH CRADLE HEADBAND

SPE ACC

• Super adjustable lightweight headband , F/O
headlight, bifurcated clear cable illumination for
long term balance, stability, comfort and wear
• High performance optical system
• Wide focus range and powerful light spot

Light Spot Distance Spot Ø
20 cm

11-68 mm

30 cm

12-101 mm

40 cm

13-136 mm

50 cm

14-173 mm

60 cm

16-208 mm

Number

Description

34-4360

IFO Focusable Fiberoptic Headlight, cradle headband, bifurcated cable
illumination, black headband

FIBEROPTIC HEADLIGHT

•
•
•
•

Ultra lightweight
Adjustable for comfortable fit
Can be used with most standard cables, 3 mm, 9 ft cable available
Cables available to fit light sources of: K. Storz, Pilling, Olympus, Wolf ACMI

Number

Description

34-4060

Fiber Optic Headlight (cable not included)

34-4061

Fiber Optic Headlight, Micro Spot (cable not included)

34-4065

Fiber Optic Cable, ACMI fittings, 3.0 mm, 9’ long

FIBEROPTIC HEADLIGHT

•
•
•
•
•

64

90° focusable headlight
Headlight module, 10-100mm variable spot
Detachable joysticks (2)
Set of cushioned detachable sweatbands
Bifurcated cable, 9” with Wolf lens proximal as standard

Number

Description

GMF-H100

Surgical headlight with cradle

Personal Lighting Systems

UNIVERSAL HALOGEN LIGHTSOURCE HL 150

•
•
•
•
•
•
•
•
•
•

Compact, lightweight halogen lightsource for universal use
Lamp
1 Halogen reflector lamp, 150 Watt, 15 V
Color temperature
3.600oK
Intensity control
stepless/mechanical diaphragm
Light guide
adapter exchangeable
Power supply
110/115 VAC or 230/240 VAC, switchable
Dimensions (WxHxD)
6.8” x 3” x 8”, 175 x 82,5 x 202 mm
Weight
3,5 kg
Power consumption
max. 160 Watt
Manufactured/tested acc. IEC 601-1 / EN 60601-1, 93/42 ECC

Number

Description

34-3135

Halogen Light Box 150 watt ACMI connector (pictured)

HALOGEN LIGHT CABLE ADAPTERS

Female connectors for F/O Cables & Flexible scope Light Cable Connectors
Number

Description

34-0754

Light box adapter for ACMI

34-0742

Light box adapter for Olympus

34-0752

Light box adapter for Storz

34-0753

Light box adapter for Wolf

34-0755

Light box adapter for Machita
Stands and Light Box Trolleys – Available upon request

Lamp
Color temperature
Intensity control
Turret, 4 ports
Non-Turret model
Power
Dimensions (WxHxD)
Weight
Regulatory

SPE ACC

LED LIGHTSOURCE

•
•
•
•
•
•
•
•
•

Light emitting diode technology (LED), life > 50,000 hours
6500° K Normal
Electronic (PWM) from 0 to 100%
ACMI, Olympus, Storz, Wolf (others available)
Available upon request
52W typical; 10-240V AC, 50/*60 Hz, worldwide operation
4.65” x 3.32” x 7.25” mm (~10” overall)
2.5lbs (1.14kg), EN60601-1-2
marked
UL60601-1, CAN/CSA C22.2 No. 601.1,

Number

Description

LLS-2000T

Premium light source, 4 -turret, generating 50% greater output than
LLS1000T

CABLES
Number

Description

34-3140

Fiber Optic Cable, ACMI fittings, 4.0mm 8’ long

34-4065

Fiber Optic Cable, ACMI fittings, 3.0 mm, 9’ long

• Other fittings available (ex. Karl Storz Pilling, Olympus, Wolf )
• Custom size cables available upon request

65

Personal Lighting Systems

HEAD MIRROR

•
•
•
•
•

Unbreakable exam mirror - Guaranteed!
Comfortable leather headband with velcro adjustability
Removable/washable headband liner
Mirror is approximately 2.9 inches in diameter
View-hole is 0.5 inches in diameter

Number

Description

34-4010

Unbreakable Head Mirror w/headband

34-4011

Unbreakable Head Mirror only

34-4012

Headband only

34-4075

Replacement liners for head band

POCKET LIGHT

•
•
•
•

Small convenient size - very lightweight
Bright white Xenon bulb
Otoscopic adapter for standard disposable specula
Nasal/Oral exam head

Number

Description

34-4000

ENT Pocket Light w/Case

SPE ACC

BRIGHTSTAR™ PORTABLE LIGHT SOURCE

• Bright, white, portable, efficient light source for Rod Lens Otoscopes, Sinus Scopes,
Indirect Vision Rod Lens Laryngoscopes, Flexible Nasopharyngoscopes
• Uses the same belt clipped battery pack as the headlight
• Portable LED, Battery powered light source

66

Number

Description

34-4020

BrightStar™ LED complete Light Source System

34-4021

ACMI scope adapter

34-4022

Richard Wolf Scope adapter

34-4023

Karl Storz, Gyrus, Olympus scope adaptor

34-4092

Charger and wall connector

Opthalmic Sponge Packing

Invotec
Number

Merocel®
Number

Description

22-70101

4405101

PVA Eye Spears

Invotec
Number

Merocel®
Number

Description

22-70300

400300

Instrument wipe

Qty/Box
Sterile

100 (10/pouch)

Microsurgery
Qty/Box
3.5” x 3.5”

20

Merocel® is a registered trademark of Medtronic-Xomed

SPE ACC

67

Cotton Tipped Applicators

COTTON TIPPED APPLICATORS
• Pure cotton end
• Sterile packed - 5 per pouch
Number

Description

2011898

Steel Applicator with Cotton Tip

Qty/Box
0.9 mm x 150 mm

100

FOG GUARD™

Invotec’s Fog-Guard™ anti-fog solution has been formulated, without alcohol, to provide
excellent levels of anti fog protection from distortion for your delicate glass optics.
• Will not damage endoscope lens

Anti-Fog
• Provided sterile, ready to use

• Packaged with a micropore, non-abrasive, radiopaque wiping pad with adhesive
back
™
FOG
GUARDDescription
Number

Qty/

Box
Invotec’s Fog-Guard™ anti-fog solution has been formulated, without alcohol, to provide
excellent levels Kitof anti
fog
protection
from
distortion
for
your
delicate
glass
optics.
One (1) Screw top dispenser bottles (6 cc) and
30900

one (1) Green micropore wiping pad with adhesive

Number

Description

30900

Kit- One (1) Screw top dispenser bottles (6 cc) and
one (1) Green micropore wiping pad with adhesive
backing, 4.3cm x 3.8cm (1 6/10” x 1 ½”)

Sterile

20 kits

SPE ACC

• Will not damage
endoscope
backing,
4.3cm xlens
3.8cm (1 6/10” x 1 ½”)
• Provided sterile, ready to use
• Packaged with a micropore, non-abrasive, radiopaque wiping pad with adhesive
back

Qty/
Box
Sterile

20 kits

Head Rest

COMFORTFOAM™ HEADREST
•
•
•
•
•
•
•
•

Manufactured from high density foam materials
Non-Slip Surface
Open Foam Softness
Flexible Positioning
Protects Sensitive Skin
Fire Retardant1
Bar Coded for Inventory Management
Enhanced Patient Stability

COMFORTFOAM™ HEADREST

68

• Number
Manufactured
from high density foam materials
Description
• Non-Slip Surface
Comfortfoam™ sculpted head rest - Blue, with ET-Anesthesia
• Open Foam Softness
• 26-71000
Flexible Positioning
Slot
• Protects Sensitive Skin
™
sculpted head rest - Blue
1
• 26-72000
Fire RetardantComfortfoam
™
• 26-73000
Bar Coded forComfortfoam
Inventory Management
sculpted head rest for child
• Enhanced Patient Stability
1

Complies With California Technical Bulletin #117

Qty/
Box
1
1
1

Sterilization Trays

Containers

Constructed of super-strong, heat
resistant, (360°F, 160°C) ULTEM® material,
the Invotec trays are designed to protect
your valuable delicate instruments during
sterilization. Offered in multiple sizes and
complimented with tops, stackable trays,
silicone finger mats and cradles, you can
build your own custom instrument tray
system.

Number

Length x Width x Depth

Description

T602575

6.0 x 2.5 x .75 inches

Base/Lid

T602512

6.0 x 2.5 x 1.25 inches

Base/Lid

T654075

6.5 x 4.0 x .75 inches

Base/Lid

T752575

7.5 x 2.5 x .75 inches

Base/Lid

T754075

7.5 x 4.0 x .75 inches

Base/Lid

T754015

7.5 x 4.0 x 1.5 inches

Base/Lid

T106075

10.0 x 6.0 x .75 inches

Base/Lid

T106015

10.0 x 6.0 x 1.5 inches

Base/Lid

T106020

10.0 x 6.0 x 1.5 inches

Base/Lid, second tray

T151015

15 x 10 x 1.5 inches

Base/Lid

T151010

15 x 10 x .75 inches

Large Tray, base/lid/mat

T151025

15 x 10 x 1.5 inches

Large Tray, base/lid/mat

T151026

15 x 10 x 1.5 inches

Large Tray, base/lid/insert/mats

T162615

16 x 2.6 x 1.5 inches (40.6cm long)

Scope Tray, base/lid

T186515

18 x 6.5 x 1.5 inches (45.7cm long)

Scope Tray, base/lid

T186530

18 x 6.5 x 3.0 inches (45.7cm long)

Scope Tray, base/lid

T-122615

12” x2.6”x 1.54”,

Scope tray, lid/cradles for two
185mm rod lens scopes

Number

Length x Width

Description

T602513

6.0 x 2.5 inches

Finger Mat

T654013

6.0 x 4.0 inches

Finger Mat

T752513

7.5 x 2.5 inches

Finger Mat

T754013

7.5 x 4.0 inches

Finger Mat

T106023

10.0 x 6.0 inches

Finger Mat

T151023

15 x 10 inches

Finger Mat

T162613

16 x 2.6 inches

Finger Mat

T186513

18 x 6.5 inches

Finger Mat

Silicone Mats

SPE ACC

T186533
18 x 6.5 x 3.0inches
Silicone Cradles

Finger Mat

Catalog No.

Description

Instrument Application

T237590

3 slot insert opposite, triple slot

Keeps 3 forceps separated

T237591

Single slot bar, round cut

Knife / instrument

T237592

Double slot bar, round cut

Knife / instrument

T237593

Triple slot bar, round cut

Knife / instrument

T237596

6 slot insert opposite triple slot

Keeps 3 forceps separated

T261691

Scope round cut, 9 and 12mm

Endoscope(s)

T261692

Scope round cut, 9mm (2)

Endoscope(s)

T387512

12 slot insert holding 6 forceps

Keeps 6 forceps separated

T387592

Double slot bar for large tray

Knives / instruments

T387593

Triple slot bar for large tray

Knives / instruments

T387594

Four slot bar for large tray

Knives / instruments

T387595

Five slot bar for large tray

Knives / instruments

T387596

6 slot insert for 6 forceps

Keeps 6 forceps separated

69

R&CS ACC

DIS

OTO ACC

OSS
LAR ACC

SPE ACC

RHINOLOGY & COSMETIC
INSTRUMENTS

RHI INS
PSB

OTO INS

LAR INS

ORO/NAS INS

Telescopes

TELESCOPES FOR NOSE AND PARANASAL SINUSES
Number Description

Diameter

Working
Length

10-0036-00

Straight Forward Wide Angle Telescope

0°

2.7 mm

110 mm

autoclavable

10-0037-00

Straight Forward Wide Angle Telescope

30°

2.7 mm

110 mm

autoclavable

10-0038-00

Straight Forward Wide Angle Telescope

70°

2.7 mm

110 mm

autoclavable

Diameter

Working
Length

Number Description
Straight Forward Wide Angle Telescope

0°

4 mm

175 mm

autoclavable

10-0046-00

Straight Forward Wide Angle Telescope

30°

4 mm

175 mm

autoclavable

10-0086-00

Straight Forward Wide Angle Telescope

45°

4 mm

175 mm

autoclavable

10-0047-00

Straight Forward Wide Angle Telescope

70°

4 mm

175 mm

autoclavable

Diameter

Working
Length

2.7 mm Ø

175 mm

Number Description
10-0039-00

Straight Forward Wide Angle Telescope

0°

RHI INS

10-0045-00

autoclavable

10-0040-00

Straight Forward Wide Angle Telescope

30°

2.7 mm Ø

175 mm

autoclavable

10-0041-00

Straight Forward Wide Angle Telescope

70°

2.7 mm Ø

175 mm

autoclavable

73

Telescope Accessories

TELESCOPE HANDLES
Number Description

length

Working Length

S40213

6.5 cm

110 mm

Telescope Handle round

Number Description

length
straight forward telescopes up to
11 cm
4 mm Ø

S40211

Telescope Handle flat

S40212

and lateral
Telescope Handle round forward-oblique
telescopes up to 4 mm Ø

S41100

Protection Tube for Sinuscopy Telescopes

Working
Length
175 mm

11 cm

175 mm

ENDOSCOPE TROCAR AND CANNULA
Number Description
Trocar and Cannula for
Sinuscopy with billshaped beak

for use with 4 mm telescopes

5 mm

8.5 cm

S18500

Trocar and Cannula for
Sinuscopy with oblique beak

for use with 4 mm telescopes

5 mm

8.5 cm

S18503

Trocar and Cannula for
Sinuscopy with oblique beak

for use with 2.7 mm telescopes

3.3 mm

7.5 cm

S18504

Trocar and Cannula for
Sinuscopy with oblique beak

for use with 3 mm telescopes

4 mm

7.5 cm

Number Description
RHI INS

Cannula
length

S18400

SUCTION IRRIGATION

S42000

Pistol Grip Telescope Suction Irrigation Handle

S42800

Sheath for telescope 2.7mm, 190mm, 0˚

S42830

Sheath for telescope 2.7mm, 190mm, 30˚

S42870

Sheath for telescope 2.7mm, 190mm, 70˚

S42900

Sheath for telescope 2.7mm, 140mm, 0˚

S42930

Sheath for telescope 2.7mm, 140mm, 30˚

S42970

Sheath for telescope 2.7mm, 140mm, 70˚

S44100

Sheath for telesccope 4.0mm, 180mm, 0˚

S44130

Sheath for telescope 4.0mm, 180mm, 30˚

S44145

Sheath for telescope 4.0mm, 180mm, 45˚

S44170

Sheath for telescope 4.0mm, 180mm, 70

Number Description

74

OuterØ

S52100

Pencil Grip Suction Irrigation Handle

S42830

Sheath for 2.7mm , telescopes 0-30˚

S52930

Sheath for 4.0mm, telescope 0-30˚

S52870

Sheath for 2.7mm. Telescope 70˚

S52970

Sheath for 4.0mm, telescope 70˚

Forceps

MAXILLARY SINUS
Number Description

Sheath

Working
Length

S15000

Biopsy and Grasping Forceps

double action oval cupped jaws 2.5 mm Ø

1.5 mm Ø

15 cm

S15070

Biopsy Forceps

double action oval cupped jaws, 3.0 mm Ø

angles down 70°

12 cm

S15110

Biopsy Forceps

double action oval cupped jaws, 3.0 mm Ø

angles down 110°

11 cm

Working
Length

Number Description
S15500

Antrum Grasping Forceps, (Heuwieser style)

RHI INS

ANTRUM GRASPING FORCEPS

retrograde opening jaws 120°

10 cm

BIOPSY AND GRASPING FORCEPS
Working
Length

Number Description
S15005

Biopsy and Grasping Forceps with malleable
sheath end

double action oval cupped
jaws 4mm Ø with vertical opening

18 cm

75

Forceps

THROUGH-CUTTING FRONTAL SINUS PUNCH FORCEPS
Working
Length

Diameter

S36201

Double action cup jaws

2 mm

55° upturned

vertical opening

14.5 cm

S36202

Double action cup jaws

2 mm

55° upturned

horizontal opening

14.5 cm

S36203

Double action cup jaws

2 mm

90° upturned

vertical opening

14.5 cm

S36204

Double action cup jaws

2 mm

90° upturned

horizontal opening

14.5 cm

RHI INS

Number Description

GIRAFFE FORCEPS

76

Number Description

Diameter

S35401

Double action cup jaws

3 mm

S35402

Double action cup jaws

3 mm

horizontal opening

S35403

Double action cup jaws

2 mm

vertical opening

S35404

Double action cup jaws

2 mm

horizontal opening

S35413

Double action cup jaws

4 mm

vertical opening

S35414

Double action cup jaws

4 mm

horizontal opening

55° upturned

vertical opening

Number Description

Diameter

S35405

Double action cup jaws

2 mm

S35406

Double action cup jaws

2 mm

horizontal opening

S35409

Double action cup jaws

4 mm

vertical opening

S35410

Double action cup jaws

4 mm

horizontal opening

90° upturned

vertical opening

Forceps

BIOPSY FORCEPS

Number Description

Diameter

S35110

Oval double action cupped jaws

2.6 mm

110° backwards cutting

horizontal opening

S35111

Oval double action cupped jaws

2.6 mm

110° backwards cutting

vertical opening

S35170

Oval double action cupped jaws

2.6 mm

70° upturned

horizontal opening

S35171

Oval double action cupped jaws

5.6 mm

70° upturned

vertical opening

S35114

Oval double action cupped jaws

4 mm

110° backwards cutting

horizontal opening

S35124

Oval double action cupped jaws

4 mm

110° backwards cutting

vertical opening
RHI INS

PEAR-SHAPED POLYP GRASPING FORCEPS

Number Description
S35300

Jaws 3 x 1.5 mm

pear-shaped

80° upturned

horizontal opening

S35304

Jaws 3 x 1.5 mm

pear-shaped

45° upturned

upturned

S35301

Jaws 3 x 1.5 mm

pear-shaped

80° upturned

sheath curved left

S35302

Jaws 3 x 1.5 mm

pear-shaped

80° upturned

sheath curved right

77

Forceps

BLAKESLEY NASAL FORCEPS
Number Description

Diameter

Size

Working
Length

S30000

Blakesley nasal forceps

Straight

0 = 3 mm

11 cm

S30001

Blakesley nasal forceps

Straight

1 = 3.5 mm

11 cm

S30002

Blakesley nasal forceps

Straight

2 = 4 mm

11 cm

S30003

Blakesley nasal forceps

Straight

3 = 5 mm

11 cm

RHI INS

BLAKESLEY-WILDE NASAL FORCEPS
Number Description

Diameter

Size

Working
Length

S30100

45° upcurved

0 = 3 mm

11 cm

Blakesley-Wilde nasal forceps

S30101

Blakesley-Wilde nasal forceps

45° upcurved

1 = 3.5 mm

11 cm

S30102

Blakesley-Wilde nasal forceps

45° upcurved

2 = 4 mm

11 cm

S30103

Blakesley-Wilde nasal forceps

45° upcurved

3 = 5 mm

11 cm

BLAKESLEY-WILDE NASAL FORCEPS
Number Description

Diameter

Size

Working
Length

S30200

Blakesley-Wilde nasal forceps

90° upcurved

0 = 3 mm

11 cm

S30201

Blakesley-Wilde nasal forceps

90° upcurved

1 = 3.5 mm

11 cm

S30202

Blakesley-Wilde nasal forceps

90° upcurved

2 = 4 mm

11 cm

S30203

Blakesley-Wilde nasal forceps

90° upcurved

3 = 5 mm

11 cm

BLAKESLEY THROUGH-CUT FORCEPS
Number Description

78

Bite

Size

Working
Length

S35800

Blakesley through-cut forceps

Straight

2 mm

0 = 3 mm

11 cm

S35801

Blakesley through-cut forceps

Straight

2.5 mm

1 = 3.5 mm

11 cm

S35802

Blakesley through-cut forceps

Straight

3.0 mm

2 = 4 mm

11 cm

S35900

Blakesley through-cut forceps

45° upcurved

2 mm

0 = 3 mm

11 cm

S35901

Blakesley through-cut forceps

45° upcurved

2.5 mm

1 = 3.5 mm

11 cm

S35902

Blakesley through-cut forceps

45° upcurved

3.0 mm

2 = 4 mm

11 cm

Forceps

BLAKESLEY ANTRUM FORCEPS
Working
Length

Number Description
S30500

Blakesley antrum forceps

tube shaft

curved left

10 cm

S30600

Blakesley antrum forceps

tube shaft

curved right

10 cm

Size

Working
Length

spoon 6 x 14 mm

11 cm

POLYP GRASPING FORCEPS
Number Description
S30400

Polyp grasping forceps

60° upcurved

round

HELMS NASAL FORCEPS
Working
Length

Number Description
S30700

Helms nasal forceps

oval cupped spoon

curved left

13 cm

S30800

Helms nasal forceps

oval cupped spoon

curved right

13 cm

Size

Working
Length

Number Description
S27001

Takahashi nasal forceps

straight

spoon 3 x 10 mm

11 cm

S27002

Takahashi nasal forceps

30° upturned

spoon 3 x 10 mm

11 cm

RHI INS

TAKAHASHI NASAL FORCEPS

STRUYCHEN NASAL CUTTING FORCEPS
Number Description

Working Length

S27500

11 cm

Struychen nasal cutting forceps

HARTMANN NASAL CUTTING FORCEPS
Number Description

Size

Working
Length

S29001

Hartmann nasal cutting forceps

1

11 cm

S29002

Hartmann nasal cutting forceps

2

11 cm

S29003

Hartmann nasal cutting forceps

3

11 cm

S29004

Hartmann nasal cutting forceps

4

11 cm

STRUEMPEL

79

Forceps

BLAKESLEY SUCTION FORCEPS
Number Description

Size

Working
Length

Blakesley suction forceps with suction channel

straight

1 = 3.5 mm

11 cm

S37002

Blakesley suction forceps with suction channel

straight

2 = 4 mm

11 cm

S37101

Blakesley suction forceps with suction channel

45° upturned

1 = 3.5 mm

11 cm

S37102

Blakesley suction forceps with suction channel

45° upturned

2 = 3.5 mm

11 cm

RHI INS

S37001

TAKAHASHI SUCTION FORCEP
Number Description

80

Size

Sheath

Working
Length

S38001

Takahashi suction forceps with integrated
suction channel

straight

1 = 3.5 mm

4 mm

10 cm

S38002

Takahashi suction forceps with integrated
suction channel

straight

2 = 2.5 mm

4 mm

10 cm

S38101

Takahashi suction forceps with integrated
suction channel

45° upturned

1 = 3.5 mm

4 mm

10 cm

S38102

Takahashi suction forceps with integrated
suction channel

45° upturned

2 = 2.5 mm

4 mm

10 cm

Forceps

BLAKESLEY SUCTION FORCEPS WITH INTEGRATED SUCTION CHANNEL
Working
Length

Size

S36800

BLAKESLEY suction forceps with suction channel straight

0 = 2.5 mm

4 mm

11 cm

S36801

BLAKESLEY suction forceps with suction channel straight

1 = 3.5 mm

4 mm

11 cm

S36802

BLAKESLEY suction forceps with suction channel straight

2 = 4 mm

4 mm

11 cm

S36900

BLAKESLEY suction forceps with suction channel 45° upcurved

0 = 2.5 mm

4 mm

10 cm

S36901

BLAKESLEY suction forceps with suction channel 45° upcurved

1 = 3.5 mm

4 mm

10 cm

S36902

BLAKESLEY suction forceps with suction channel 45° upcurved

2 = 4 mm

4 mm

10 cm

Jaw Size

Sheath

Working
Length

RHI INS

Number Description

BLAKESLEY SUCTION FORCEPS FOR CHILDREN
Number Description
S36700

Blakesley suction forceps for children with
integrated suction channel

straight

2.5 mm

2.7 mm

10 cm

S36745

Blakesley suction forceps for children with
integrated suction channel

45° upcurved

2.5 mm

2.7 mm

10 cm

81

Forceps

THROUGHCUTTING FORCEPS WITH INTEGRATED SUCTION CHANNEL
Number Description

Bite

Working
Length

Throught cutting forceps with integrated suction channel

straight

2 mm

10 cm

S35201

Throught cutting forceps with integrated suction channel

45° upcurved

2 mm

10 cm

S35204

Throught cutting forceps with integrated suction channel

shaft 15° upcurved

2 mm

10 cm

RHI INS

S35200

FOKKENS BIOPSY FORCEPS
Number Description

82

Bite

Working
Length

S36000

Fokkens Biopsy Forceps

straight

3 mm Ø

8 cm

S36045

Fokkens Biopsy Forceps

45° upcurved

Round 3 mm Ø

11 cm

Forceps

SUPER PUNCH THRU CUT FORCEPS
Number Description

Bite

size

Working
Length

S36400

Super Punch Thru Cut forceps

straight

Oval 2 mm

0

13 cm

S36401

Super Punch Thru Cut forceps

straight

Oval 2.5 mm

1

13 cm

S36402

Super Punch Thru Cut forceps

straight

Oval 3 mm

2

13 cm

S36500

Super Punch Thru Cut forceps

upcurved

Oval 2 mm

0

13 cm

S36501

Super Punch Thru Cut forceps

upcurved

Oval 2.5 mm

1

13 cm

S36502

Super Punch Thru Cut forceps

upcurved

Oval 3 mm

2

13 cm

RHI INS

83

Punches, Back Biters and Kerrisons

ROTATING BACK BITER
Description

Bite

Working
Length

S35015

Rotating Backbiting Antrum Punch, finger post
facilitates 360° rotation

pediatric size: 1.5
mm

10 cm

S35025

Rotating Backbiting Antrum Punch, finger post
facilitates 360° rotation

2.5 mm

10 cm

S35050

Toby micro backbiter finger post facilitates 360° rotation

curved down

10 cm

RHI INS

Number

STAMMBERGER TYPE SIDEBITING ANTRUM PUNCH

84

Working
Length

Number

Description

S34801

Sidebiting antrum punch

leftside downward and
forward

throughcut

10 cm

S34802

Sidebiting antrum punch

rightside downward and
forward

throughcut

10 cm

Punches, Back Biters and Kerrisons

BACKBITING ANTRUM PUNCHES
Bite

Working
Length

upside backwards cutting

2.5 mm

10 cm

Antrum Punch - adult
size

left side backwards cutting

2.5mm

10 cm

S35002

Antrum Punch - adult
size

right side backwards cutting

2.5mm

10 cm

Number

Description

Bite

Working
Length

S35020

Antrum Punch pediatric

upside backwards cutting

1.5 mm

10 cm

S35021

Antrum Punch pediatric

left side backwards cutting

1.5 mm

10 cm

S35022

Antrum Punch pediatric

right side backward cutting

1.5 mm

10 cm

Number

Description

S35000

Antrum Punch - adult
size

S35001

RHI INS

CIRCULAR CUTTING PUNCHES
Number

Description

Diameter

Working
length

S34935

Circular Cutting Punch cutting in a full circle
of 360°

3.5 mm

18 cm

S34945

Circular Cutting Punch cutting in a full circle
of 360°

4.5 mm

18 cm

S34965

Circular Cutting Punch cutting in a full circle
of 360°

3.5 mm

17 cm

S34975

Circular Cutting Punch cutting in a full circle
of 360°

4.5 mm

18 cm

65°
upturned

85

Punches, Back Biters and Kerrisons

BIOPSY FORCEPS

Width

Working
Length

90° upbiting

4 mm

14 cm

HAJEK Sphenoid Punch

90° downbiting

4 mm

14 cm

S12201

HAJEK Sphenoid Punch

45° upbiting backward

4 mm

14 cm

S12202

HAJEK-KOFLER Sphenoid
Punch

45° downbiting
backward

4 mm x 4 mm

14 cm

S12301

HAJEK-KOFLER Sphenoid
Punch

45° upbiting
forward

4 mm x 4 mm

14 cm

S12302

HAJEK-KOFLER Sphenoid
Punch
bite 2mm x 2mm

45° upbiting
forward

4 mm x 4 mm

14 cm

Description

S12001

HAJEK Sphenoid Punch

S12002

RHI INS

Number

BEYER ANTRUM PUNCH

86

Number

Description

S12500

BEYER Antrum Punch

S12600

BEYER Antrum Punch

Width

Working
Length

90°
throughbiting
upwards

2 mm

9 cm

90°
throughbiting
backward

2 mm

9 cm

Punches, Back Biters and Kerrisons

HAJEK-KOFLER ROTATABLE SPHENOID PUNCH
Working
Length

Number

Description

S13000

Hajek-Kofler Sphenoid punch

reversible 360°

slender pattern

17 cm

RHI INS

ROTATABLE SPHENOID PUNCH
Number

Description

S13100

Sphenoid
punch

reversible
360°

throughcutting

slender
pattern

Bite

Working
Length

2 mm

14.5 cm

87

Punches, Back Biters and Kerrisons

KERRISON ANTRUM PUNCH
Bite

Working
Length

90° upbiting

2 mm

18 cm

FS-Kerrison sphenoid punch

90° upbiting

3 mm

18 cm

S12922

FS-Kerrison sphenoid punch

40° upbiting

2 mm

18 cm

S12923

FS-Kerrison sphenoid punch

40° upbiting

3 mm

18 cm

Number

Description

Bite

Working
Length

S12402

Antrum punch

throughcutting

2 mm

18 cm

S12403

Antrum punch

throughcutting

3 mm

15 cm

S13100

Sphenoid
pattern

2 mm

14.5cm

Number

Description

S12410

Stylet, for removal of the bone material from the deposit of S12402 and S12403

S12800

Ethmoid punch

Description

S12902

FS-Kerrison sphenoid punch

S12903

RHI INS

Number

88

punch

-

slender

reversible 360°

backward cutting

2.5 mm

17 mm

Punches, Back Biters and Kerrisons

FRONTAL KERRISON PUNCH
Number

Description

S12602

Frontal sinus punch

70° up

S12603

Frontal sinus punch

70° up

Bite

Working
Length

40° up biting forward

2 mm

17.5 cm

40° up biting forward

mm

17.5 cm

RHI INS

89

Scissors

INTRANASAL SCISSORS
Working
Length

Number

Description

S26200

Nasal scissors

serrated
blades

straight

13 cm

S26201

Nasal scissors

serrated
blades

curved left

13 cm

S26202

Nasal scissors

serrated
blades

curved right

13 cm

S26210

Nasal scissors - small

serrated
blades

3.5 mm

straight

12 cm

S26211

Nasal scissors - small

serrated
blades

3.5 mm

curved right

12 cm

S26212

Nasal scissors - small

serrated
blades

3.5 mm

curved left

12 cm

RHI INS

EYMANN NASAL SCISSORS

90

Working
Length

Number

Description

S26000

Heymann nasal scissors

smooth blades

straight

9.5 cm

S26100

Heymann nasal scissors

serrated blades

straight

9.5 cm

S26101

Heymann nasal scissors

smooth blades

curved left

9.5 cm

S26102

Heymann nasal scissors

smooth blades

curved right

9.5 cm

S26009

Heymann nasal scissors

serrated blades

straight

small size

9 cm

S26011

Heymann nasal scissors

serrated blades

straight

small size

11 cm

Number

Description

S42000

BELLUCCI Scissors

Working
Length
straight

10 cm

Scissors

Number

Description

Working Length

R40700

Caplan septum scissors

straight

22 cm

R40600

Caplan septum scissors

angled

22 cm

Number

Description

R68210

Goldman
scissors

Fox

tenotomy

R68310

Goldman
scissors

Fox

tenotomy

R68413

Goldman
scissors

Fox

tenotomy

R68613

Goldman
scissors

Fox

tenotomy

Number

Description

R39100

Cottle dorsal scissors

Working
Length
straight

13 cm

serrated

curved

13 cm

TC supercut

straight

13 cm

TC supercut

curved

13 cm

RHI INS

serrated

Working Length
angular

16 cm

91

Scissors

Description

Working Length

R39000

Fomon dorsal scissors angular

delicate

13.5 cm

R39001

Fomon dorsal scissors angular

standard pattern

13.5 cm

R38612

Fomon lower lateral curved
scissors

13.5 cm

Number

Description

Working Length

R38410

Wilmer Angled sh/sh scissors

10 cm

Number

Description

R76514

Joseph scissors

straight

14 cm

R76614

Joseph scissors

curved

14 cm

Number

Description

R79615

Reynolds dissection scissors

RHI INS

Number

92

Working Length

Working Length
curved

delicate

15 cm

Scissors

Number

Description

Working Length

R38712

Kilner (Ragnell) scissors

Number

Description

R68210

Stevens Tenotomy scissors

straight

blunt

11.5 cm

R68310

Stevens Tenotomy scissors

curved

blunt

11.5 cm

curved flat tips

12 cm

Working Length

Stevens Tenotomy scissors

straight

sharp

11.5 cm

Stevens Tenotomy scissors

straight

curved

11.5 cm

Number

Description

R77010

Strabismus scissors

blunt/blunt

straight

10.5 cm

R77110

Strabismus scissors

blunt/blunt

curved

10.5 cm

R77212

Strabismus scissors

blunt/blunt

straight

11.5 cm

R77312

Strabismus scissors

blunt/blunt

curved

11.5 cm

Number

Description

Working Length

R047712

Kaye Blepharoplasty scissors

11.5 cm

RHI INS

R68411
R68410

Working Length

93

RHI INS

Scissors

94

Number

Description

Working Length

R47519

Gorney facelift scissors

19 cm

Number

Description

R77510

Iris scissors

Working Length
sharp/sharp

straight

10.5 cm

R77610

Iris scissors

sharp/sharp

curved

10.5 cm

R77712

Iris scissors

sharp/sharp

straight

11.5 cm

R77812

Iris scissors

sharp/sharp

curved

11.5 cm

Number Description

Working Length

R77901

12 cm

Wire cutter universal

Knives

Number Description

Working Length

R13000

15 cm

Freer Mucosa knife “D”

Number Description

Diameter

Working
Length

R19001

Ballenger swivel knife

bayonet

3 mm

20 cm

R19002

Ballenger swivel knife bayonet

bayonet

4 mm

20 cm

R65015

Ballenger swivel knife bayonet

bayonet

5 mm

20 cm

R65003

Ballenger swivel knife bayonet

straight

3 mm

20 cm

R65004

Ballenger swivel knife bayonet

straight

4 mm

20 cm

R65005

Ballenger swivel knife bayonet

straight

5 mm

20 cm

Number Description
S03000

Cottle nasal knife

Working Length
rounded edges

Number Description
S32000

Masing nasal knife

15 cm

Working Length
slight curve round tip

13 cm

Number Description
R29003

#3 Knife Handle

R29007

#7 Knife Handle

R71065

Maltz cartilage knife

Working Length
angled

16 cm

Number Description
R353600

Fomon double-edge knife

RHI INS

Number Description

Working Length
curved blunt tip

16 cm

Working
Length

Number Description
R34000

Joseph button-end knife

straight

15 cm

R34100

Joseph-Converse button-end knife (Bistory)

curved

15 cm

R35000

Joseph nasal knife

straight

pointed tip

15 cm

R35100

Joseph nasal knife

curved

pointed tip

15 cm

R35200

Joseph nasal knife

straight

blunt tip

15 cm

R35300

Joseph nasal knife

curved

blunt tip

15 cm

R71060

Joseph angled cartilage knife (Hockey Stick)

15 cm

95

Osteotomes, Chisels and Saws

JOSEPH NASAL SAW
Number

Working Length

R48100

straight

19 cm

R48001

bayonet

19 cm

R48002

bayonet

19 cm

R76022

bend to left

17 cm

R76021

bend to right

17 cm

FREER SEPTAL CHISEL
Number

Working Length

R20001

straight

16 cm

R20002

curved

16 cm

RHI INS

BALLENGER “V” SEPTAL GOUGE
Number

Width

Working Length

R60704

4 mm

16 cm

R60706

6 mm

16 cm

R60708

8 mm

16 cm

KILLIAN BAYONET NASAL GOUGE
Number

Working Length

R21000

17cm

R21100

17cm

COTTLE OSTEOTOME
Number

96

Width

Working
Length

R07004

graduated

straight

4 mm

18 cm

R07007

graduated

straight

7 mm

18 cm

R07009

graduated

straight

9 mm

18 cm

R07012

graduated

straight

12 mm

18 cm

Osteotomes, Chisels and Saws

COTTLE DOUBLE GUARDED OSTEOTOME
Number

Width

Working Length

R61516

16 mm

18 cm

COTTLE DOUBLE GUARDED OSTEOTOME
Number
R10516

cross bar

Width

Working
Length

16 mm

18 cm

RUBIN DOUBLE GUARDED OSTEOTOME
Number

Width

Working Length

R06010

10 mm

18 cm

R06012

12 mm

18 cm

R06014

14 mm

18 cm

RHI INS

CINELLI DOUBLE GUARDED OSTEOTOME
Number

Width

Working Length

R060510

10 mm

18 cm

R060512

12 mm

18 cm

R060514

14 mm

18 cm

R060516

16 mm

18 cm

FOMON SINGLE GUARDED CHISEL
Number

Width

Working Length

R63904

4 mm

17 cm

R63905

5 mm

17 cm

R63906

6 mm

17 cm

R63907

7 mm

17 cm

97

Osteotomes, Chisels and Saws

MASING SINGLE GUARDED CHISEL
Number

Working Length

R10000

straight

17.5 cm

R10001

curve left

17.5 cm

R10002

curve right

17.5 cm

CONVERSE SINGLE GUARDED OSTEOTOME
Number
R07900

Working Length
straight

19 cm

R07901

left

19 cm

R07902

right

19 cm

SILVER SINGLE GUARDED OSTEOTOME
Number

Width

Working Length

straight

18 cm

left

18 cm

S12502

right

18 cm

RHI INS

S12500
S12501

NEIVERT SINGLE GUARDED OSTEOTOME
Number

Working Length

R12000

straight

20 cm

R12001

curved

20 cm

R12002

curved

20 cm

Number

Width

Working Length

R11000

4 mm

18 cm

WEST CHISEL

98

Osteotomes, Chisels and Saws

WEST GOUGE
Number

Width

Working Length

R11100

4 mm

18 cm

MINI OSTEOTOME
Number

Width

Working Length

R07602

2 mm

18 cm

R07603

3 mm

18 cm

RHI INS

99

Elevators

FREER ELEVATOR
Working
Length

Number

Description

N15000

double-ended

USA Model

20 cm

R15100

double-ended

sharp/blunt

18 cm

GORNEY SUCTION ELEVATOR
Number

Description

S05800

Elevator with stylet

Working
Length
3mm tip

19 cm

LEMPERT JOSEPH ELEVATOR
Number

Description

Width

Working
Length

R26052

straight

2 mm

20 cm

R26057

straight

3 mm

20 cm

R26058

curved

3 mm

20 cm

R26070

wide

6 mm

20 cm

R26071

wide

6 mm

18 cm

RHI INS

MCKENTY ELEVATOR
Number

Description

Width

Working
Length

R02004

single ended

4 mm

14.5 cm

R02005

single ended

5 mm

14.5 cm

R02500

double-ended

21.5 cm

KILLIAN SEPTUM ELEVATOR
Number

Description

Working Length

R16000

sharp/blunt

short

18 cm

R16100

sharp/blunt

long

22cm

MASING ELEVATOR

100

Number

Description

R05000

double-ended graduated

Working
Length
sharp/blunt

21.5 cm

Elevators

COTTLE ELEVATORS
Working
Length

Number

Description

R04500

double-ended, graduated

R05500

tunneling elevator

blunt

21 cm
23 cm

PIERCE ELEVATOR
Number

Description

R35821

double ended

Working
Length
right - left

21 cm

PENNINTON ELEVATOR
Number

Description

R05600

double-ended

Working
Length
right/left

21 cm

SEWALL ANTRUM
Number

Description

Working Length

R18000

Antrum elevator

19.5 cm

RHI INS

PROBES
Working
Length

Number Description
S18725

Frontal sinus ostium
seeker

double-ended

curved

19 cm

S18619

Maxillary sinus
ostium seeker

double-ended

ball

19 cm

101

Septum Instruments

ASCH SEPTUM STRAIGHTENING FORCEPS
Working
Length

Number
R45000

Straightening forceps

23cm

COTTLE-WALSHAM STRAIGHTENING FORCEPS
Working
Length

Number

Description

R44000

Septum straightening forceps

both sides

23 cm

R44101

Septum straightening forceps

left

23 cm

R44102

Septum straightening forceps

right

23 cm

RHI INS

KRESSNER TURBINATE CRUSHING FORCEPS
Working
Length

Number

Description

R47003

Crushing forceps

2.5 x 60 mm

20 cm

R47004

Crushing forceps

4 x 70 mm

20 cm

R47005

Crushing forceps

5 x 75 mm

20 cm

BOISE NASAL FRACTURE ELEVATOR
Number

Description

R61000

“Butter Knife”

Working
Length
blunt, oval

18 cm

GOLDMAN SEPTUM DISPLACER
Number

Description

R61100

Septum displacer

Working Length
short

20 cm

RUBIN SEPTUM MORCELIZER

102

Working
Length

Number

Description

R42000

Rubin septum morcelizer

R76570

Guard for Rubin septum morcelizer

double action

20 cm

Septum Instruments

JANSON MIDDLETON DOUBLE ACTION FORCEPS
Number

Description

Working
Length

R35600

Double action through-cut septal forceps

19 cm

R35500

Double action oval spoon nasal forceps

19 cm

STRUYCHEN THROUGH-CUT FORCEPS
Number

Description

Working
Length

S27500

small through-cut forceps,

11 cm

S27501

large through-cut forceps,

11 cm

RHI INS

103

Curettes

ANTRUM CURETTE
Number Description

Working Length

S18001

Oval

size 1

19 cm

S18002

Oval

size 2

19 cm

S18003

Oval

size 3

19 cm

S18101

Round

small size

19 cm

S18102

Oblong

small size

19 cm

S18103

Oblong

large size

19 cm

S18203

Oblong

small size

forward cutting

19 cm

S18204

Oblong

small size

backward cutting

19 cm

SINUS FRONTAL CURETTE
Number Description

Working Length

Oblong

small size

55° curved

19 cm

S18105

Oblong

small size

90° curved

19 cm

RHI INS

S18104

HALLE ANTRUM CURETTE
Number Description
S06001

malleable

Working Length
size 1

21 cm

S06002

malleable

size 2

21 cm

S06003

malleable

size 3

21 cm

ANTRUM CURETTE
Number Description

104

Working Length

S06101

curved left

21 cm

S06102

curved right

21 cm

Curettes

COAKLEY ANTRUM CURETTE
Number Description
Size 1

Size 3

Size 5

Size 2

Size 4

Size 6

Working Length

S03001

size 1

17 cm

S03002

size 2

17 cm

S03003

size 3

17 cm

S03004

size 4

17 cm

S03005

size 5

17 cm

S03006

size 6

17 cm

FAULKNER ANTRUM CURETTE
Number Description
S04000

Double ended

RHI INS

105

Speculas

TIECK-HALLE NASAL SPECULUM
Working
Length

Number
S40000

For infants

13.5 cm

S43001

For adults

13.5 cm

BECKMAN ENDAURAL SPECULUM
Number

Description

Working
Length

S06501

Small

15 cm

S06502

Medium

15 cm

S06503

Large

15 cm

HARTMANN NASAL SPECULUM
Number

Description

S43001

Large

Working Length
35 mm

13.5 cm

RHI INS

HARTMANN-HALLE NASAL SPECULUM
S41001

Size 1

15 cm

S41002

Size 2

15 cm

S41003

Size 3

15 cm

HARTMANN ECONOMY
Number

Description

Working
Length

S43500

Office nasal speculum

14 cm

VIENNA NASAL SPECULUM

106

Number

Description

Working Length

S41601

Small

14.5 cm

S41602

Medium

14.5 cm

S41603

Large

14.5 cm

Speculas

COTTLE NASAL SPECULUM WITH SET SCREW
Number

Description

Working
Length

S00001

35 mm

15 cm

S00002

50 mm

15 cm

S00003

75 mm

15 cm

S00004

90 mm

15 cm

COTTLE NASAL SPECULUM WITHOUT SET SCREW
Number

Description

Working
Length

S00101

35 mm

15 cm

S00102

50 mm

15 cm

S00103

75 mm

15 cm

S00104

90 mm

15 cm

KILLIAN NASAL SPECULUM
Description

Working
Length

S42001

35 mm

13 cm

S42002

50 mm

13 cm

S42003

75 mm

13 cm

S42004

90 mm

13 cm

RHI INS

Number

THUDICHUM (GOLDSMITH) SPRING NASAL
SPECULUM
Number

Description

S41301

#1

S41302

#2

S41303

#3

AUFRECHT NASAL RETRACTOR

Number

Description

Working
Length

R22500

60 mm blade

16 cm

R22600

45 mm blade

16 cm

107

Speculas

RHI INS

COTTLE ALAR RETRACTOR

108

Number

Description

Working
Length

R19000

Vein retractor

15 cm

R19500

Vein retractor

15 cm

Retractors

SENN RETRACTOR
Number Description

Working Length

R65000

Sharp retractor

16 cm

R65100

Dull retractor

16 cm

REGNELL-DAVIS RETRACTOR
Number
R12514

Working Length
Retractor

14 cm

PLASTICS RAKES

R67004

Sharp retractor

Working Length
4 prong

16 cm

R67003

Sharp retractor

3 prong

16 cm

R67002

Sharp retractor

2 prong

16 cm

R67001

Sharp retractor

1 prong

16 cm

Number Description

RHI INS

Number Description

Working Length

R68004

Dull retractor

4 prong

16 cm

R68003

Dull retractor

3 prong

16 cm

R68002

Dull retractor

2 prong

16 cm

R68001

Dull retractor

1 prong

16 cm

COTTLE RETRACTOR
Number Description

Working Length

R18000

14 cm

Retractor with 4 prong blunt, middle two teeth shortened

109

Hooks

COTTLE TENACULUM HOOK
Number Description

Working Length

R15000C

delicate

angled

16 cm

R151000

delicate

curved

16 cm

COTTLE NARES DOUBLE HOOK

RHI INS

Number

Working Length

R16000

Sharp on Left, dull on right double hook

14 cm

R16100

Sharp on Right, dull on left double hook

14 cm

R16200

Sharp double hook

14 cm

COTTLE-NEIVERT KNIFE GUIDE/NARES DOUBLE BALL HOOK
Number Description

Working Length

R20000

20 cm

Large double ball hook/knife guide

NEIVERT-MASING KNIFE GUIDE AND NARES RETRACTOR

110

Number Description

Working Length

R20500

20 cm

Knife guide and nares retractor

Hooks

FOMON DOUBLE BALL NASES HOOK
Number Description
R16600

Double ball nases hook

Working Length
10 mm wide

16 cm,

CONVERSE DOUBLE END HOOK
Number Description

Working Length

R24200

12 cm

Alar double hook

KILNER ALAR DOUBLE HOOK RETRACTOR
Working Length

R24300

8 cm

double hook retractor

RHI INS

Number Description

COTTLE (MILLIARD) DOUBLE HOOK THIMBLE RETRACTOR
Number Description
R22800

double hook thimble retractor

FREER-GUTHRIE MICRO DOUBLE HOOK
Number Description

Working Length

R16400

15 cm

Micro double hook sharp

111

Hooks

JOSEPH DOUBLE HOOK
Number Description

Working Length

R16502

2 mm

16 cm

R16505

5 mm

16 cm

R16507

7 mm

16 cm

R16510

10 mm

16 cm

NERVE HOOK
Number Description

Working Length

R61301

18 cm

RHI INS

Blunt hook

VOLKMAN BONE HOOK

112

Number Description

Working Length

R05701

21.5 cm

Sharp bone hook

Rasps

WEINER ANTRUM RASP
Number Description

Working Length

R08101

18 cm

Sharp rasp

Number Description

Working Length

R08102

18 cm

Dull rasp

RHI INS

WATSON-WILLIAMS ANTRUM RASP
Number Description

Working Length

R08500

23 cm

Antrum Rasp

FRONTAL SINUS RASP
Number Description

Working Length

R18110

Frontal Sinus Rasp

strong pattern

R18111

Frontal Sinus Rasp

slender pattern

113

Rasps

LEWIS “SWEEPER” RASP
Number Description

Working Length

R56600

Rasp “Sweeper”

Downcut

fine

18 cm

R56700

Rasp “Sweeper”

Downcut

coarse

18 cm

LEWIS “SWEEPER” TC RASP
Number Description

Working Length

R36501

TC rasp “Sweeper”

Downcut

fine

18 cm

T36502

TC rasp “Sweeper”

Downcut

coarse

18 cm

RHI INS

COTTLE DOWNCUT RASP
Number Description

Working Length

R54000

21 cm

Downcut rasp

AUFRICHT CURVED GLABELLA RASP
Number Description

Working Length

R54500

Push up cut rasp

21 cm

R54600

Pull down cut

21 cm

MALTZ SLOTED RASP

114

Number Description

Working Length

R53500

18 cm

Sloted rasp

Rasps

MASING - FOMON DOUBLE ENDED NASAL RASP
Number Description

Working Length

R53000

Double ended nasal rasp

#1&2

21 cm

R53100

Double ended nasal rasp

#3&4

21 cm

MILLER-COLBURN DOUBLE ENDED NASAL RASP
Number Description
R38001

Double ended nasal rasp

Working Length
Serrated

Glabella

19 cm

R38002

Double ended nasal rasp

Serrated

fine

wide

curved

19 cm

R38003

Double ended nasal rasp

Serrated

coarse

wide

straight

19 cm

R38004

Double ended nasal rasp

Serrated

coarse

short

19 cm

R38005

Double ended nasal rasp

Serrated

coarse

straight

19 cm

wide

Number Description

Working Length

Double ended nasal rasp

cross hatched

Glabella

R38102

Double ended nasal rasp

cross hatched

fine

wide
wide

R38103

Double ended nasal rasp

cross hatched

coarse

R38104

Double ended nasal rasp

cross hatched

coarse

R38105

Double ended nasal rasp

cross hatched

coarse

19 cm

wide

curved

19 cm

straight

19 cm

short

19 cm

straight

19 cm

RHI INS

R38101

FOMON DOUBLE ENDED RASP
Working
Length

Number Description
R52001

Double ended TC rasp

#1&2

xfine - fine

20 cm

R52002

Double ended TC rasp

#3&4

20 cm

R52003

Double ended TC rasp

#5&6

20 cm

R52004

Double ended TC rasp

#7&8

20 cm

R52005

Double ended TC rasp

# 9 & 10

coarse - xcoarse

20 cm

COTTLE NASAL TC RASP
Number Description

Working
Length

R39221

21 cm

TC rasp downcut medium

115

Sinus Suctions

V. EICKEN SINUS ANTRUM CANNULA
Number Description

Outer diameter

Working Length

S49602

Long curved

LUER-Lock

2.5mm

12 cm

S49603

Long curved

LUER-Lock

3 mm

12 cm

S49604

Long curved

LUER-Lock

4 mm

12 cm

Short curved

LUER-Lock

2.5 mm

12 cm

Short curved

LUER-Lock

3 mm

12 cm

S49614

Short curved

LUER-Lock

4 mm

12 cm

S49702

Long curved

Malleable

2.5 mm

12 cm

S49703

Long curved

Malleable

3.0 mm

12 cm

S49704

Long curved

Malleable

4.0 mm

12 cm

RHI INS

S49612
S49613

KAHN-FRAZIER FRONTAL SINUS SUCTION
Number Description

116

Inner
ID

Shaft

Size

Working
Length

S11610

Frontal Sinus Suction Tube with cut-off
hole

10 Fr

malleable

1

slightly
curved

15 cm

S11710

Frontal Sinus Suction Tube with cut-off
hole

10 Fr

malleable

2

strongly
curved

15 cm

Sinus Suctions

FRAZIER/FERGUSON NASAL STYLE
Working
Length

Number Description
S43006

Frazier suction tube

Stainless

6 Fr

10 cm

S10008

Frazier suction tube

Stainless

8 Fr

10 cm

S10010

Frazier suction tube

Stainless

10 Fr

10 cm

S10012

Frazier suction tube

Stainless

12 Fr

10 cm

S10015

Frazier suction tube

Stainless

15 Fr

10 cm

Working
Length

Number Description

10 cm

S11006

FRAZIER Suction Tube with calibrations

marked at 5 cm - 9 cm

6 Fr

10 cm

S11008

FRAZIER Suction Tube with calibrations

marked at 5 cm - 9 cm

8 Fr

10 cm

S11010

FRAZIER Suction Tube with calibrations

marked at 5 cm - 9 cm

10 Fr

10 cm

Working
Length

Number Description
S11210

Frazier suction tube

stainless

slightly curved right

10 Fr

10 cm

S11212

Frazier suction tube

stainless

slightly curved right

12 Fr

10 cm

S11310

Frazier suction tube

stainless

slightly curved left

10 Fr

10 cm

S11312

Frazier suction tube

stainless

slightly curved left

12 Fr

10 cm

S11410

Frazier suction tube

stainless

strongly curved right

10 Fr

RHI INS

Working
Length

Number Description

10 cm

S11412

Frazier suction tube

stainless

strongly curved right

12 Fr

10 cm

S11510

Frazier suction tube

stainless

strongly curved left

10 Fr

10 cm

S11512

Frazier suction tube

stainless

strongly curved left

12 Fr

10 cm

FRAZIER/FERGUSON NASAL STYLE WITH BALL END
Working
Length

Number Description
S10016

Frazier suction tube

stainless

ball ended

6 Fr

10 cm

S10018

Frazier suction tube

stainless

ball ended

8 Fr

10 cm

S10020

Frazier suction tube

stainless

ball ended

10 Fr

10 cm

S10022

Frazier suction tube

stainless

ball ended

12 Fr

10 cm

S10025

Frazier suction tube

stainless

ball ended

15 Fr

10 cm

117

Mallets

COTTLE MALLET
Number

Description

Weight

Working
Length

R13000

Mallet

240 g

19 cm

MALLET WITH NYLON CAPS
Number

Description

Weight

Working
Length

R13500

Mallet with replaceable nylon
caps

140 g

18 cm

R13501

Nyon facings for S13500 mallet
, 1 pair

RHI INS

THEISS MINI MALLET
Number

Description

Weight

Working
Length

R53516

Mini mallet

140 g

16.5 cm

TARDY TYPE MALLET
Number

Description

Weight

Working
Length

R528320

Rhinoplasty mallet

320 g

17 cm

R528321

Nylon Facing for
Tardy, I Pair

QUISLING INTRANASAL HAMMER

118

Number

Description

R413900

Quisling Intranasal hammer

Needle Holders

OLSEN-HEGAR NEEDLE HOLDER SCISSORS
Number Description

Working
Length

R14614

14 cm

Needle holder scissors

R14618

Needle holder scissors

17 cm

R15019

Needle holder scissors

19 cm

GILLIES CURVED
Working
Length

R15516

16 cm

Hand grasped needle holder/scissors

RHI INS

Number Description

DERF NEEDLE HOLDER
Working
Length

Number Description
R05012

Needle Holder

stainless

serrated

12 cm

R05012T

Needle Holder

TC

serrated

12 cm

119

Needle Holders

WEBSTER NEEDLE HOLDER
Working
Length

Number Description
R06013

Needle holder

smooth

Stainless

13 cm

R46013

Needle holder

smooth

TC

13 cm

HALSEY NEEDLE HOLDER
Working
Length

RHI INS

Number Description
R06413

Needle holder

serrated

stainless

13 cm

R46613

Needle holder

serrated

TC

13 cm

R06613

Needle holder

smooth

stainless

13 cm

R46413

Needle holder

smooth

TC

13 cm

CRILE NEEDLE HOLDER
Working
Length

Number Description
R07015

120

Needle holder

jaw slot

stainless

15 cm

R47015

Needle holder

jaw slot

TC

15 cm

R07215

Baby needle holder

no slot

stainless

15 cm

R46815

Baby needle holder

no slot

TC

15 cm

Needle Holders

RYDER NEEDLE HOLDER
Working
Length

Number Description
R43413

Fine tipped needle holder

TC

13 cm

R43415

Fine tipped needle holder

TC

15 cm

CASTROVIEJO NEEDLE HOLDER
Working
Length

Number Description
Needle TC holder

straight

smooth

18 cm

R30453

Needle TC holder

curved

smooth

18 cm

R30450

Needle TC holder

straight

serrated

18 cm

R30451

Needle TC holder

curved

serrated

18 cm

RHI INS

R30452

WIRE TWISTERS
Number Description

Working
Length

R0917

17 cm

MGH Stubby Serrated with Jaw slot

121

Needle Holders

STERUM STUBBY SERRATED WITH JAW SLOT
Number Description

Working
Length

R53353416

Sterum Stubby TC

12.5 cm

R53353918

Sterum Stubby TC

18 cm

CORWIN FLAT TIP
Working
Length

RHI INS

Number Description
R55601

Finger ring wire twister

flat end

R55602

Finger ring wire twister

round end

R55603

Finger ring wire twister

oblong end

MAYO HEGAR NEEDLE HOLDER
Working
Length

Number Description

122

S14016

Needle holders

stainless

16 cm

S14018

Needle holders

stainless

18 cm

S14020

Needle holders

stainless

20 cm

R40016

Needle holders with TC Inserts

stainless

16 cm

R40018

Needle holders with TC Inserts

stainless

18 cm

R40020

Needle holders with TC Inserts

stainless

20 cm

Tissue Thumb Forceps

Working
Length

Number

Description

R25212

Adson with teeth

Number

Description

R110/12

Micro Adson with teeth

Number

Description

Working
Length

R25112

Adson without teeth

12 cm

Standard 1x2

12 cm

Working
Length
1x2

12 cm

Number

Description

Working Length

R25312

Micro Adson without teeth

12 cm

Number Description

Working Length

R25012

12 cm

Brown adson

Number Description

Working Length

R25612

Adson pickups TC inserts

w/o teeth

12 cm

R25712

Adson pickups TC inserts

1x2 teeth

12 cm

Number Description

Working Length

R76004

Jewelers forceps straight #4

11 cm

R76005

Jewelers forceps straight #5

11 cm

R04701

Castroviego forceps

1x2 teeth

Tip

Working
Length

.12 mm

12 cm

RHI INS

Number Description

Working
Length

Number Description
R01000

Cottle columella forceps

standard pattern

10.5 cm

R01100

Cottle columella forceps

child/small pattern

8.5 cm

Working
Length

Number Description
R04210

Bishop Harmon fine tissue forceps

serrated

8.5 cm

R04212

Bishop Harmon fine tissue forceps

1x2 teeth

8.5 cm

R04211

Bishop Harmon delicate fine tissue forceps serrated

8.5 cm

R04213

Bishop Harmon delicate fine tissue forceps 1x2 teeth

8.5 cm

Number Description
R27015

Cottle fixation forceps with teeth

bayonete with fix screw

123

Miscellaneous

UNIVERSAL ATOMIZER KABIERSKE
Number Description
O22810

Universal atomizer Kabierske (S40100)

POLYP SNARES AND ACCESSORIES
Number Description

Working Length

S11500

24 cm

RHI INS

Wild nasal polyp snare

NASAL POLYP SNARE KRAUSE
Number Description

Working Length

S61520

26 cm

Nasal polyp snare Krause

FRONTAL SINUS RASP
Number Description

124

S61540

Polyp snare wires precut 12 each

S21042

Polyp snare wire coil

S21043

Polyp snare wire coil

.3 mm

Miscellaneous

APPLICATORS
Number Description

Working Length

S12116

Farrell applicator

triangular

0.9 mm

14 cm

S11513

Farrell applicator

twist tip

1.1 mm

14 cm

GROVED DIRECTOR
Number Description

Working Length

S91511

14 cm

Groved director

BOWMAN LACRIMAL PROBES SILVER
Number Description

Working Length

Bowman silver probes

0000/00

12.5 cm

S03401

Bowman silver probes

00/0

12.5 cm

S03402

Bowman silver probes

0/1

12.5 cm

S03404

Bowman silver probes

1/2

12.5 cm

S03406

Bowman silver probes

2/3

12.5 cm

S03408

Bowman silver probes

3/4

12.5 cm

RHI INS

S03400

CARTILAGE SMASHER
Number Description
S450000

Working Length

Cottle cartilage smasher

125

Miscellaneous

SEPTUM TONSIL NEEDLES
Number Description

Shaft

Tip

S01100

Septum tonsil needle

knee bent angular

LUER-Lock

0.8 mm

22 g

S11400

Septum tonsil needle

straight

LUER-Lock

0.8 mm

22 g

S11300

Septum tonsil needle

right angle tip

LUER-Lock

0.8 mm

22 g

S11700

Septum tonsil needle

bayonet

LUER-Lock

0.8 mm

22 g

SOLUTION BOWLS

RHI INS

Number Description

126

S97030

Stainless solution bowl

30 cc

1 oz

S97050

Stainless solution bowl

50 cc

1.6 oz

S97100

Stainless solution bowl

100 cc

3 oz

S97150

Stainless solution bowl

150 cc

5 oz

Measuring Instruments

Description

S63100

Jamison Caliper

Number

Description

S00040

Castroviego Caliper

Number

Description

S43715

Ruler 6”

stainless

0-8 mm

Length
stainless

20 mm

8 cm

stainless
RHI INS

Number

127

R&CS ACC

DIS

OTO ACC

OSS
LAR ACC

SPE ACC

RHI INS

PARANASAL SKULL BASE
INSTRUMENTS

PSB

OTO INS

LAR INS

ORO/NAS INS

Retractors

FLEXIBLE TENSION ARM
Number Description
O18800

Arm for holding nasal speculum and retractors

O18801

Rotation OR table clamp for above

COTTLE MASING NASAL SPECULUM
Number Description
S97635

Nasal speculum for use with flexible tension arm

35 mm

S97650

Nasal speculum for use with flexible tension arm

50 mm

S97675

Nasal speculum for use with flexible tension arm

75 mm

S97690

Nasal speculum for use with flexible tension arm

90 mm

AUFRICHT RETRACTOR
PSB

Number Description
S97300

Retractor for use with flexible tension arm

stainless

DOUBLE PRONG RETRACTOR
Number Description
S97400

Dull double prong retractor for use flexible tension arm

stainless

131

Forceps

INSTRUMENTS AS DESCRIBED BY DRAF
Number Description

Working Length

Ethmoid forceps

straight

13 cm

S38416

Ethmoid forceps

straight

16 cm

S38419

Ethmoid forceps

straight

19 cm

S38513

Ethmoid forceps

60° upcurved

13 cm

S38516

Ethmoid forceps

60° upcurved

16 cm

S38519

Ethmoid forceps

60° upcurved

19 cm

S38613

Ethmoid forceps

90° upcurved

13 cm

S38616

Ethmoid forceps

90° upcurved

16 cm

S38619

Ethmoid forceps

90° upcurved

19 cm

S38713

Ethmoid scissors

straight

13 cm

S38716

Ethmoid scissors

straight

16 cm

S38719

Ethmoid scissors

straight

19 cm

PSB

S38413

ELONGATED PARANASAL FORCEPS
Number Description
S38901

132

Conchotome

Working
Length

Jaw
very delicate

oval throughcutting

3 x 1 mm

straight

14 cm

Forceps

PARANASAL FORCEPS
Number Description

Working Length

S38423

Ethmoid forceps

straight

oval cupped

3 x 1.5 mm

13 cm

S38426

Ethmoid forceps

straight

oval cupped

3 x 1.5 mm

16 cm

S43010

Ethmoid forceps

straight

delicate serrated

16 cm

S43015

Ethmoid forceps

straight

rough serrated

16 cm

TUBULAR ELONGATED PARANASAL FORCEPS

S42100

Ethmoid forceps

“Blakesley Type”

straight

size 0

17 cm

S42101

Ethmoid forceps

“Blakesley Type”

straight

size 1

17 cm

S42102

Ethmoid forceps

“Blakesley Type”

straight

size 2

17 cm

S42200

Ethmoid forceps

“Blakesley Type”

45° upcurved

size 0

17 cm

S42201

Ethmoid forceps

“Blakesley Type”

45° upcurved

size 1

17 cm

Working
Length

Number Description
S42300

Ethmoid forceps

PSB

Working
Length

Number Description

“Takahashi type”

straight

spoon 3 x 10 mm

17 cm

133

R&CS ACC

DIS

OTO ACC

OSS
LAR ACC

SPE ACC

RHI INS

PSB

INSTRUMENTS

OTOLOGY

OTO INS

LAR INS

ORO/NAS INS

Tuning Forks

STEEL TUNING FORKS
Number Description
020505

Hartmann tuning fork set with case

Set of 5: c2-512, c3-1024, c4-2048, c-128, c1-256

Number Description
O20508

Hartmann tuning fork set with case

Complete set: O20512-O20561

Number Description
O20512

Hartmann tuning fork

c2-512

O20513

Hartmann tuning fork

c3-1024

O20514

Hartmann tuning fork

c4-2048

O20515

Hartmann tuning fork

c5-4096

O20532

French tuning fork

c1-32

O20559

Hartmann tuning fork

c-64

O20560

Hartmann tuning fork

c-128

O20561

Hartmann tuning fork

c1-256

ALUMINUM TUNING FORKS
Number Description
O20705

Aluminum tuning fork set with case

Set of 5: c-128, c1-256, c-512, c3-1024, c-2048

Number Description
O20710

Aluminum tuning fork

c-128

O20711

Aluminum tuning fork

c1-256

O20712

Aluminum tuning fork

c-512

O20713

Aluminum tuning fork

c3-1024

O20714

Aluminum tuning fork

c-2048

OTO INS

NOISE BOX - OTOSCOPE
Number Description
O20950

Jansen Otoscope
Complete with one physician ear piece and
six ear pieces for patient

Black

Rack included

Number Description
O20950

Barany Noise Apparatus with hard rubber connector

Black

Rack included

137

Ear Speculum

Number Description
O20010

Brunings Pneumatic Ear Speculum
Complete Set with lens, 4 speculas, rubber bulb, and wooden case

Number Description

Diameter

O20020

Brunings Ear Speculum

Size 0

5.5 mm

O20021

Brunings Ear Speculum

Size 1

6.5 mm

O20022

Brunings Ear Speculum

Size 2

7.5 mm

O20023

Brunings Ear Speculum

Size 3

8.5 mm

O20024

Brunings Ear Speculum

Size 4

9.5 mm

O20025

Brunings Ear Speculum

Size 5

10.5 mm

Number Description
O20013

Brunings Diagnostic Head

Full lens

Number Description
O20014

Brunings Operating Head

Segmented lens

O20015

Rubber Bulb

Fitting the Brunings and Siegle lenses

Number Description

Diameter

Siegle Pheumatic Ear Speculum lens

O20061

Siegle Ear Speculum

6.0 mm

O20062

Siegle Ear Speculum

6.5 mm

O20063

Siegle Ear Speculum

7.5 mm

OTO INS

O20053

Number Description

138

Diameter

O20161

Boucheron Ear Speculum for Adults

Set of 4

O20166

Boucheron Ear speculum for adults

4.5 mm

O20167

Boucheron Ear speculum for adults

5.5 mm

O20168

Boucheron Ear speculum for adults

6.5 mm

O20169

Boucheron Ear speculum for adults

4.5 mm

Ear Speculum

Number Description

Diameter

O20100

Hartmann Ear Speculum for children

Set of 3

3.0, 4.5, 5 mm

O20101

Hartmann Ear Speculum for children

3.0 mm

O20102

Hartmann Ear Speculum for children

4.5 mm

O20103

Hartmann Ear Speculum for children

5 mm

Number Description

Diameter

O20110

Hartmann Ear Speculum for adults

Set of 3

5.5, 6.5, 7.5 mm

O20111

Hartmann Ear Speculum for adults

5.5 mm

O20112

Hartmann Ear Speculum for adults

6.5 mm

O20113

Hartmann Ear Speculum for adults

7.5 mm

Number Description
O20130

Toynbee Ear Speculum for adults

Set of 3

5.5, 6.5, 7.5 mm

O20131

Toynbee Ear Speculum for adults

Set of 4

4.5, 5.5, 6.5, 7.5mm

O20136

Toynbee Ear Speculum for adults

4.5 mm

O20137

Toynbee Ear Speculum for adults

5.5 mm

O20138

Toynbee Ear Speculum for adults

6.5 mm

O20139

Toynbee Ear Speculum for adults

7.5 mm

Number Description

Diameter

Ear Speculum

Set of 6

O20192

Ear Speculum

2 mm

O20193

Ear Speculum

3 mm

O20194

Ear Speculum

4 mm

O20195

Ear Speculum

5 mm

O20196

Ear Speculum

6 mm

O20197

Ear Speculum

7.5 mm

Number Description

OTO INS

O20190

Diameter

O20300

Zoellner Operating Ear Speculum

Black-finish

Oval

Set of 6

O20311

Zoellner Operating Ear Speculum

Black-finish

Oval

5.5 x 6.5 mm

O20312

Zoellner Operating Ear Speculum

Black-finish

Oval

6.5 x 7.5 mm

O20313

Zoellner Operating Ear Speculum

Black-finish

Oval

7.5 x 8.5 mm

O20314

Zoellner Operating Ear Speculum

Black-finish

Oval

8.5 x 9.5 mm

O20315

Zoellner Operating Ear Speculum

Black-finish

Oval

9.5 x 10.5 mm

O20316

Zoellner Operating Ear Speculum

Black-finish

Oval

10.5 x 11.5 mm

139

Ear Curettes

Number Description

Diameter

O21250

Buck-Wullstein micro ear curettes

blunt

16 cm

0000

0.9 mm

Buck-Wullstein micro ear curettes

blunt

16 cm

000

1.1 mm

O21252

Buck-Wullstein micro ear curettes

blunt

16 cm

00

1.3 mm

O21253

Buck-Wullstein micro ear curettes

blunt

16 cm

0

1.8 mm

O21254

Buck-Wullstein micro ear curettes

blunt

16 cm

1

2.1 mm

length

Size

Diameter

O21431

Shapleigh ear curettes

serrated

14 cm

1

O21432

Shapleigh ear curettes

serrated

14 cm

2

length

Size

Diameter

Number Description

OTO INS

Size

O21251

Number Description

140

length

O21109

Buck ear curettes

sharp

15 cm

00

1.5 mm

O21110

Buck ear curettes

sharp

15 cm

0

1.9 mm

O21111

Buck ear curettes

sharp

15 cm

1

2.5 mm

O21112

Buck ear curettes

sharp

15 cm

2

2.7 mm

O21113

Buck ear curettes

sharp

15 cm

3

3.4 mm

O21114

Buck ear curettes

sharp

15 cm

4

4.0 mm

O21115

Buck ear curettes

sharp

15 cm

5

4.5 mm

Loops and Hooks

EAR LOOPS
Number Description

length

Size

O21401

Billeau ear loop

straight

15.5 cm

1

O21402

Billeau ear loop

straight

15.5 cm

2

O21403

Billeau ear loop

straight

15.5 cm

3

Number Description

Diameter

length

Size

Diameter

O21407

Billeau-Micro ear loop

straight

16 cm

00

2.0 mm

O21408

Billeau-Micro ear loop

straight

16 cm

0

2.5 mm

O21409

Billeau-Micro ear loop

straight

16 cm

1

3.0 mm

length

Size

Diameter

blunt

13.5 cm

Number Description
O21410

Langenbeck ear loop

Number Description
O21415

Coxeter ear loop - Double ended

length
blunt

Number Description

Size

14.5 cm

Diameter
4.5 mm / 5.5 mm

length

Size

Weber-Loch ear loop

straight

15 cm

0

O21421

Weber-Loch ear loop

straight

15 cm

1

O21422

Weber-Loch ear loop

straight

15 cm

2

OTO INS

O21420

Diameter

EAR LEVERS

Number Description

length

O21440

16 cm

Moldenhauer ear lever

141

Loops and Hooks

Number Description

length

O21505

16 cm

Zaufal ear lever

Number Description
O21510

Yankauer-Jansen ear lever

Length
45°

15 cm

Number Description

Length

O21606

Wagener ear lever

sharp

14 cm

O21607

Wagener ear lever

blunt

14 cm

EAR HOOKS

Number Description

OTO INS

O21470

Gross ear spoon and hook

Size
oval

Number Description
O21475

142

Gross ear curette and hook

length
12 cm

Size
round

length
12 cm

Number Description

Size

length

O21511

Jansen ear hook

1

15 cm

O21512

Jansen

2

15 cm

Loops and Hooks

Number Description
O21520

Size

Allport ear hook

length
16 cm

Number Description

Size

length

O21571

Hartmann ear hook

1

16 cm

O21572

Hartmann ear hook

2

16 cm

Number Description

Size

length

O21601

Wagener ear hook

2.0

14 cm

O21602

Wagener ear hook

2.5

14 cm

O21603

Wagener ear hook

3.0

14 cm

O21604

Wagener ear hook

3.5

14 cm

O21605

Wagener ear hook

4.0

14 cm

Number Description

Size

length

O21651

Day ear hook

1

16 cm

O21652

Day ear hook

2

16 cm

Ear Probes

OTO INS

Number Description

length

O21681

Stacke ear probe

Nickel silver

11 cm

O21684

Stacke-Frenzel ear probe

Sterling silver

9 cm

Number Description

length

O21690

Wullstein probe

Silver

26 cm

O21695

Bloch ear probe

Sterling silver

11 cm

143

Perforators

SICKLE SHAPED KNIVES AND LANCETS
Number Description

length

O21750

Lempert sickle shaped knife

16 cm

O21752

Lempert sickle shaped knife

17 cm

O21760

Politzer sickle shaped knife

16 cm

O21802

Buck lancet

15 cm

O21806

Lempert lancet

14 cm

O21810

Lempert lancet

15 cm

O21811

Lempert lance

45°

15 cm

TYMPANUM PERFORATORS

O21823

Number Description

Length

O21823

16 cm

Politzer Tympanum perforator

O21825
O21825

Lucae Tympanum perforator

for children

18 cm

O21827

Lucae Tympanum perforator

for adults

18 cm

O21827

O21830

Politzer Tympanum perforator

reversible

19 cm

O21833

Politzer Tympanum perforator

screw locking handle

15 cm

OTO INS

O21830

O21833

O21835

144

Lucae Tympanum perforator

19 cm

O21835

Perforators

O21845

Sexton Tympanum knife

18 cm

O21847

Sexton Tympanum knife

18 cm

O21850

Sexton Tympanum knife

18 cm

O21853

Sexton Tympanum knife

18 cm

O21857

Sexton Tympanum knife

18 cm

O21858

Sexton Tympanum knife

screw locking handle

18 cm

OTO INS

145

Ear Catheters

OTO INS

EAR CATHETERS

146

Number Description

Length

size

Diameter

O22011

Hartmann ear catheter

14 cm

1

2.5 mm

O22012

Hartmann ear catheter

14 cm

2

3.0 mm

O22013

Hartmann ear catheter

14 cm

3

3.5 mm

O22014

Hartmann ear catheter

14 cm

4

4.0 mm

O22015

Hartmann ear catheter

14 cm

5

5.0 mm

O22021

Troeltsch Ear catheter

14 cm

1

2.5 mm

O22022

Troeltsch Ear catheter

14 cm

2

3.0 mm

O22023

Troeltsch Ear catheter

14 cm

3

3.5 mm

O22024

Troeltsch Ear catheter

14 cm

4

4.0 mm

O22025

Troeltsch Ear catheter

14 cm

5

5.0 mm

O22030

Tube connector for Hartmann/Troeltsch catheters

Olive-shaped

Bags and Blowers

AIR BAGS
Number Description

Diameter

O22055

Politzer air bag with concial metal plate - rubber bulb only

O22062

Politzer air bag nasal tip

15 mm

O22063

Politzer air bag nasal tip

17 mm

O22064

Politzer air bag nasal tip

22 mm

O22069

Politzer air bag connector with plugin cone and screw thread

POWDER BLOWER
Number Description
O22810

Kabierske powder blower
complete set: 3 cannulas for ear, nose, throat and larynx

O22811

Kabierske spare glass bottle

O22812

Kabierske valve rubber bulb

O22816

Kabierske laryngeal cannula

curved

13 cm x 5 1/8”

O22817

Kabierske nasal cannula

straight

11 cm x 4 3/8”

O22818

Kabierske ear cannula

straight

8 cm x 3 1/8”

30 ml

OTO INS

147

Instrument Sets

EAR INSTRUMENT SETS

OTO INS

Number Description

148

O21901

Sprague ear instrument

sickle-shaped knife

O21902

Sprague ear instrument

blunt-tip hook

O21903

Sprague ear instrument

button-tip probe

O21904

Sprague ear instrument

tympanum perforating lancet

O21905

Sprague ear instrument

ear curette

O21906

Sprague ear instrument

ear spoon

O21909

Sprague ear instrument

tubular handle

Suction Tips

Number Description

diameter

O22101

Rosen suction tip with Luer-Lock attachment

Straight

0.70 x 80 mm

O22102

Rosen suction tip with Luer-Lock attachment

Straight

0.90 x 80 mm

O22103

Rosen suction tip with Luer-Lock attachment

Straight

1.20 x 80 mm

O22111

Rosen suction tip with Luer-Lock attachment

angled

0.70 x 65 mm

O22112

Rosen suction tip with Luer-Lock attachment

angled

0.90 x 65 mm

O22113

Rosen suction tip with Luer-Lock attachment

angled

1.20 x 65 mm

O22114

Rosen suction tip with Luer-Lock attachment

angled

1.50 x 65 mm

O22115

Rosen suction tip with Luer-Lock attachment

angled

2.00 x 65 mm

Number Description

Diameter

O22210

Baron suction tip with finger cut off

1.0 x 75 mm

O22215

Baron suction tip with finger cut off

1.5 x 75 mm

O22220

Baron suction tip with finger cut off

2.0 x 75 mm

Number Description

Length Diameter

O22141

Wullstein flexible suction tip with
Luer Cone

cylindrical

Sterling
16 cm
Silver

1.5 mm

O22142

Wullstein flexible suction tip with
Luer Cone

cylindrical

Sterling
16 cm
Silver

2.0 mm

O22148

Wullstein flexible suction tip with
Luer Cone

conical

Sterling
16 cm
Silver

1.5 mm

OTO INS

Number Description
O22148

Tube connector with Luer cone and cut off plate

for Wellstein and Rosen suction tubes

Number Description
O22146

Wullstein irrigating suction handle with Luer cone
Compatible with Wullstein irrigating/suction tubes

149

Suction Tips

Working
Length

Number Description

Diameter

O22230

Zollner suction tube with finger plate and Luer cone
Complete with 1 slip on cannula

O22235

Zollner micro suction cannula only for suction tube

30 mm

0.5 mm

O22237

Zollner micro suction cannula only for suction tube

30 mm

0.7 mm

Number Description

Working
Length

Diameter

O22261

Frazier suction tube

110 mm

1.00 mm x 190 mm

O22262

Frazier suction tube

110 mm

2.00 mm x 190 mm

0.7 mm

OTO INS

Number Description

150

O22271

Hartmann suction tip

right ear

O22272

Hartmann suction tip

left ear

Number Description

Size

diameter

O22309

House suction tip

1

0.9 + 0.7 mm

O22312

House suction tip

2

1.2 + 0.9 mm

O22315

House suction tip

3

1.5 + 1.2 mm

O22318

House suction tip

1

1.8 + 1.8 mm

O22325

House suction tip

2

2.5 + 2.0 mm

O22330

House suction tip

3

3.0 + 2.0 mm

O22345

House suction tip

4

4.5 + 2.0 mm

Elevators

PERIOSTEOTOMES, ELEVATOR

Number Description
O26010

Muck periosteal knife

13 cm

Number Description
O26020

Politzer mastoid knife

13 cm

Number Description
O26052

Lempert elevator

size 2 mm

straight

18 cm

O26057

Lempert elevator

size 2 mm

curved

18 cm

O26058

Lempert elevator

size 3 mm

curved

18 cm

OTO INS

Number Description
O26040

Wullstein raspatory

width

length
17 cm

151

OTO INS

Elevators

152

Number Description

width

length

O26070

Lempert raspatory

6 mm

20 cm

O26071

Lempert raspatory

6 mm

18 cm

Number Description

width

length

O26080

12 mm

17 cm

Jansen raspatory

Snares

EAR POLYPUS SNARES

Number Description

Size

O21010

16 cm

Krause Ear Polypus Snare

Number Description

Size

O21030

16 cm

Wilde Ear Polypus Snare

Number Description

Size

O21042

Snare-Wire, coil

10 meters

0.2 mm Ø

O21043

Snare-Wire, coil

10 meters

0.3 mm Ø

Number Description

Size

O21047

Snare-Loops, pre-shaped

bundle/ 100 pieces

0.2mm Ø

O21048

Snare-Loops, pre-shaped

bundle/ 100 pieces

0.3 mm Ø

O21049

Snare-Loops, pre-shaped

bundle/ 100 pieces

0.35 mm Ø

OTO INS

153

Ronguers

MASTOID RONGEURS
Number Description
O26203

Kerrison Rongeur chisel-edge punch

0

80 mm

O26204

Kerrison Rongeur chisel-edge punch

1

80 mm

O26205

Kerrison Rongeur chisel-edge punch

2

80 mm

O26206

Kerrison Rongeur chisel-edge punch

3

80 mm

Number Description
O26251

Citelli Rongeur atticus punch

1

60 mm

O26252

Citelli Rongeur atticus punch

2

60 mm

O26253

Citelli Rongeur atticus punch

3

60 mm

OTO INS

Number Description
O26265

Brunings rongeur, chisel edged punch

4 mm

O26266

Brunings rongeur, chisel edged punch

6 mm

Number Description
O26272

154

Beyer rongeur atticus punch

2 mm

Ear Forceps

PUNCHES, MALLEUS NIPPERS
Number Description
O24805

Width

Davol forceps

3 x 2 mm

Number Description

Width

O24814

Dieter malleus punch

chisel-edge

up cutting

1.3 mm

O24815

Dieter malleus punch

chisel-edge

down cutting 1.3 mm

O24816

Dieter malleus punch

chisel-edge

right cutting

1.3 mm

O24817

Dieter malleus punch

chisel-edge

left cutting

1.3 mm

Number Description
O23020

Hartmann ear dressing forceps

delicate pattern

13.5 cm

O23021

Hartmann ear dressing forceps

standard pattern

13.5 cm

standard pattern

14 cm

Number Description
O23040

Tilly ear dressing forceps

OTO INS

Number Description
O23112

Hartmann ear forceps

14 cm

O23122

Hartmann ear forceps

20 cm

O23132

Hartmann ear forceps

22 cm

155

OTO INS

Ear Forceps

156

Number Description

length

O23142

Hartmann-Noyes ear forceps

14 cm

O23152

Hartmann-Noyes ear forceps

duckbill

14 cm

O23163

Hartmann ear forceps

1 x 2 teeth

14 cm

O23170

Weingartner ear forceps

O23201

Hartmann-Herzfeld ear forceps

14 cm

14 cm

2 mm

O23202

Hartmann-Herzfeld ear forceps

14 cm

2.2 mm

O23203

Hartmann-Herzfeld ear forceps

14 cm

2.5 mm

O23204

Hartmann-Herzfeld ear forceps

14 cm

3.0 mm

O23211

Hartmann-Herzfeld ear forceps

14 cm

2.0 mm

O23212

Hartmann-Herzfeld ear forceps

14 cm

2.2 mm

O23213

Hartmann-Herzfeld ear forceps

14 cm

2.5 mm

O23214

Hartmann-Herzfeld ear forceps

14 cm

3.0 mm

Number Description

Length

O23250

Hartmann ear forceps

14 cm

O23260

Struempel ear forceps

14 cm

O23261

Struempel-baby ear forceps

14 cm

O23270

Hartmann ear forceps

2.0 mm

Ear Forceps

Number Description

Length

O23301

Hartmann ear forceps

smooth jaws

O23303

Hartmann ear forceps

smooth jaws

O23312

Hartmann ear forceps

serrated jaws

O23314

Hartmann ear forceps

serrated jaws

O23322

Bellucci grasping forceps*

heavy pattern

14 cm
1 x 2 teeth

14 cm
14 cm

angled up

14 cm

* may also be used as prosthesis applying or wire bending forceps

Number Description
O23401

Ear forceps

smooth jaws

4 x 0.5 mm

O23412

Ear forceps

serrated jaws

O23414

Ear forceps

serrated jaws

angled up

3 x 0.5 mm

O23416

Ear forceps

serrated jaws

right

3 x 0.5 mm

O23417

Ear forceps

serrated jaws

left

3 x 0.5 mm

O23422

Ear forceps

serrated jaws

long

7 x 0.5 mm

4 x 0.5 mm

OTO INS

Number Description
O23512

Ear forceps

serrated jaws

straight

4 x 0.4 mm

O23514

Ear forceps

serrated jaws

angled up

4 x 0.4 mm

O23712

Ear forceps

delicate with oval cup jaws

straight

1 x 0.9 mm

O23714

Ear forceps

delicate with oval cup jaws

angled up

1 x 0.9 mm

O23716

Ear forceps

delicate with oval cut jaws

angled right

1 x 0.9 mm

O23717

Ear forceps

delicate with oval cut jaws

angled left

1 x 0.9 mm

157

Ear Forceps

Number Description
O23912

Ear forceps

oval cup jaws

straight

0.6 x 0.5 mm

O23914

Ear forceps

oval cup jaws

up

0.6 x 0.5 mm

O23916

Ear forceps

oval cup jaws

right

0.6 x 0.5 mm

O23917

Ear forceps

oval cup jaws

left

0.6 x 0.5 mm

OTO INS

Number Description

158

diameter

O25012

Ear forceps

serrated jaws

straight

5 x 0.5 mm

O25014

Ear forceps

serrated jaws

up

4 x 0.5 mm

O25023

Ear forceps

serrated jaws

long

7 x 0.5 mm

O25030

Ear forceps

with round cup jaws

O25035

Ear forceps

with oval cut jaws

1.2 x 0.9 mm

O25060

Wullstein-Blakesley
Ear forceps

jaws fenestrated

5 x 2 mm

0.9 mm

Ear Forceps

WIRE BENDING FORCEPS

Number Description
O24611

Schuknecht Wire crimper

curved down

6.0 x 0.8 mm

Number Description
O24614

McGee wire bending forceps

curved down

3.5 x 0.8 mm

O24615

McGee wire bending forceps

curved down

4.5 x 0.8 mm

FORCEP PROTECTOR
• autoclavable

Number Description

Length

O24990

80 mm

Teflon forcep protector

OTO INS

Number Description

Shaft Width

Shaft Length

O24812

1.5 mm

65 mm

Tabb crura nipper

159

Ear Forceps

Number Description
O24910

Graven grasping forceps

Shaft Length
serrated jaws

3 x 1 mm

Number Description

OTO INS

O24919

160

Fuller forceps

70 mm

Shaft Length
smooth jaws

6 x 0.8 mm

75 mm

Ear Scissors

Number Description
O24110

Shea-Bellucci Ear scissors

blunt tip blades

straight

O24112

Shea-Bellucci Ear scissors

straight tip blades

straight

O24116

Shea-Bellucci Ear scissors

semi-sharp tip

curved right

O24117

Shea-Bellucci Ear scissors

semi-sharp tip

curved left

Number Description
O24211

Bellucci ear scissors

sharp/blunt tip

straight

O24212

Bellucci ear scissors

sharp tip blades

straight

O24213

Bellucci ear scissors

sharp tip

angled up

O24216

Bellucci ear scissors

sharp tip

curved right

O24217

Bellucci ear scissors

sharp tip

curved left

OTO INS

Number Description
O25052

Ear scissors

sharp tip blades

straight

O25054

Ear scissors

sharp tip

angled up

O25056

Ear scissors

sharp tip

curved right

O25057

Ear scissors

sharp tip

curved left

161

Malleus Forceps

Number Description
O24810

Shaft Length

Lempert Malleus forceps

11.5 cm

Number Description

OTO INS

O24835

162

Wullstein malleus nipper

Length

chisel edge 3 mm long

Shaft Length

Length

80 mm

15 cm

Needles / Picks

Number Description
O30601

Barbara sharp needle/pick

O30603

Barbara sharp needle/pick

O30604

Rosen sharp needle/pick

O30605

Rosen blunt needle/pick

O30606

Rosen blunt needle/pick

OTO INS

163

Hooks

Number Description
O30607

Austin hook

1.5 mm

90°

O30613

Austin hook

0.3 mm

25°

O30616

Austin hook

0.6 mm

25°

O30620

Austin hook

1.0 mm

25°

O30641

Austin hook

1.5 mm

45°

O30643

Austin hook

2.5 mm

45°

O30645

Shea hook

oblique pick

blunt

2.0 mm

45°

O30649

Austin hook

attic dissector

blunt

3.0 mm

90°

O30641

Austin hook

1.5 mm

45°

O30643

Austin hook

2.5 mm

45°

O30645

Shea hook

oblique pick

blunt

2.0 mm

45°

O30649

Austin hook

attic dissector

blunt

3.0 mm

90°

OTO INS

Number Description

164

O30772

Antoli-Candela hook

angled right

0.6 mm

90°

O30773

Antoli-Candela hook

angled left

0.6 mm

90°

O30792

Antoli-Candela hook

right

1.0 mm

90°

O30793

Antoli-Candela hook

left

1.0 mm

90°

Hooks

Number Description
O30775

McGee hook

curved up

0.5 mm

O30780

McGee hook

curved up

1.0 mm

O30785

McGee hook

curved down

0.5 mm

O30790

McGee hook

curved down

1.0 mm

Number Description
O30802

Fisch hook

0.2 mm

O30806

Plester hook

0.6 mm

OTO INS

165

Tympanoplasty Knives

Number Description

Diameter

Diameter

O30810

Antoli-Candela incision knife

1.0 mm

45°

O30815

Antoli-Candela incision knife

1.5 mm

45°

O30820

Antoli-Candela incision knife

2.0 mm

45°

O30823

Antoli-Candela incision knife

2.3 mm

45°

O30825

Antoli-Candela incision knife

2.5 mm

45°

O30830

Antoli-Candela circular cutting knife

1.0 mm

90°

O30835

Antoli-Candela circular cutting knife

1.5 mm

90°

O30840

Antoli-Candela circular cutting knife

2.0 mm

90°

O30843

Antoli-Candela circular cutting knife

2.3 mm

90°

O30845

Antoli-Candela circular cutting knife

2.5 mm

90°

O30901

House round knife for includo-stapedial joint

1.0 mm

30°

O30903

Goldmann knife-elevator for metal wall

3.0 mm

45°

Number Description

Size

O30906

1.5 mm

45°

OTO INS

Rosen knife curette

Number Description
O30911

166

Antoli-Candela Round knife

Size
for incudo-stapedial joint

1.0 mm

45°

Tympanoplasty Knives

Number Description

Size

O30922

2.0 mm

Austin round knife weapon

Number Description

Size

O30925

3.0 mm

Gerlach round knife

90°

90°

Size

O30935

Shea tympanoplasty knife

1.5 x 1 mm

45°

O30938

Shea tympanoplasty knife

4.0 x 2.5 mm

60°

O30939

Harrison tympanoplasty knife

45°

O30947

Harrison tympanoplasty knife

90°

OTO INS

Number Description

167

Tympanoplasty Knives

Number Description

Size

O31061

House tympanoplasty knife

4.0 x 1.0 mm

O31063

House tympanoplasty knife

3.0 x 1.0 mm

O31075

Gray tympanoplasty knife

3.5 mm Ø

OTO INS

Number Description

168

O30953

Rosen incision knife

45°

O30955

Hough incision knife

2.0 x 1- 2 mm

45°

O30958

House lancet knife

2.0 x 1.0 mm

45°

O30965

Shea incision knife

2.0 x 1.5 mm

90°

O30967

Austin incision knife

1.8 x 1.2 mm

90°

Tympanoplasty knives

Number Description
O31003

Guilford-Wright flap knife

2 mm

O31005

Plester flap knife

3.5 mm

O31017

Plester incision knife

2.5 mm

O31032

Austin sickle knife

3.0 x 1.0 mm

O31035

Austin incision knife for footplate

Number Description
Tabb tympanoplasty knife

1.5 x 1 - 1.15 mm

O31041

House sickle knife #1

6.0 x 1.5 mm

OTO INS

O31040

Number Description
O31046

Schuknecht sickle knife

5.0 x 1.0 mm

169

Micro Elevators

Number Description

Width

O31103

Goldmann elevator

oval shape

slight curve

O31111

House stapes elevator

O31131

Shea elevator

right

1.2 mm

O31132

Shea elevator

left

1.2 mm

2.5 mm
12 mm

Number Description
O31171

Shambaugh-Derlacki elevator

Length
blunt

14 cm

OTO INS

Number Description

170

Length

Width

O30922

Austin round knife

angled up 90°

2 mm Ø

O31102

Antoli-Candela elevator

curved

1.8 mm

O31115

Rosen elevator

15 x 1.5 mm

O31121

Rosen elevator

15 x 1.0 mm

O31122

Rosen elevator

15 x 1.2 mm

Micro Elevators

Number Description

Width

O31143

Schuknecht elevator

flat

tip slightly curved up

O31150

Hough excavator

heavy pattern

right

O31151

Hough excavator

heavy pattern

left

Number Description

1 mm

width

length

O31175

Shambaugh-Derlacki elevator

angled tip

2.0 mm

14.4 cm

O31176

Shambaugh-Derlacki duckbill elevator

slightly curved

3.0 mm

14.5 cm

OTO INS

171

Stapes Curettes

Number Description
O31290

Double-ended curette for Stapedectomy

pointed

small

17 cm

O31292

Double-ended curette for Stapedectomy

pointed

large

17 cm

OTO INS

Number Description

172

Length

Diameter

O31270

House Double-ended curette for stapedectomy

cups slightly
1.0 mm
angled forward

1.2 mm

O31275

House Double-ended curette for stapedectomy

cups slightly
1.5 mm
angled forward

1.8 mm

O31280

House Double-ended curette for stapedectomy

cups strongly
1.0 mm
angled forward

1.2 mm

O31285

House Double-ended curette for stapedectomy

cups strongly
1.5 mm
angled forward

1.8 mm

Footplate Drill

Number Description

Diameter

O36590

Larkin hand perforator

trocar point

0.8 mm

O36592

Larkin hand penetrator

0.8 mm

O36594

Larkin hand trephine

0.8 mm

OTO INS

173

OTO INS

Mobilizers

174

Number Description

Width

O31461

Rose Mobilizer

1.8 mm

O31465

Goldmann Mobilizer with ball tip

O31468

Goldmann pluggar with ball tip

angled up 25°

Diameter

0.8 mm
1.0 mm

Measuring and Cutting

Number Description
O31410

Hough measuring rod

markers at 3.5 mm

4 mm

O31433

Austin wire guide and applicator

v-notch

light curve

4.5 mm

Number Description
O38950

Piston cutting jig

OTO INS

175

R&CS ACC

DIS

OTO ACC

OSS
LAR ACC

SPE ACC

RHI INS

PSB

OTO INS

LARYNGEAL

INSTRUMENTS

LAR INS

ORO/NAS INS

Operating Laryngoscopes

KLEINSASSAR TYPE
Number

Size

Description

L30001

18 cm

Adult Large

L30002

18 cm

Medium

L30003

18 cm

Small

L30004

18 cm

Anterior commissure

L30005

22 cm

Anterior commissure, long neck

L30006

15 cm

Child

L30007

13 cm

Small Child

SPREADABLE OPERATING LARYNGOSCOPES
Number

Size

Description

L30001S

17 cm

Adult Large

L30002S

17 cm

Medium

L30003S

18 cm

Small

L30004S

18 cm

Anterior commissure

L30005S

22 cm

Anterior commissure, long neck

L30006S

15 cm

Child

L30007S

13 cm

Small Child

L30001 & L30001S

L30002 & L30002S

L30003 & L30003S

L30004-L30005 &
L30004S-L30005S

L30006 & L30006S

L30007 & L30007S

BENJAMIN SLIM
Number

Size

Description

L550-1327

17 cm

Adult Medium

LARYNGOSCOPE HOLDER AND CHEST SUPPORT
Number

Ring Size

Rod Size

Description

L30400

9.5 cm Ø

34 cm

Adult size chest support with rubber ring

L30500

9.5 cm Ø

24 cm

Child size rod only with rubber ring
Rubber ring replacement for L30400-L30500

LAR INS

L30401

LEWY LARYNGOSCOPE HOLDER
Number

Description

L30390

Lewy Larngoscope holder and chest brace

L3039H

Lewy handle for Kleinsassar, spreadables and Benjamin Slim operating laryngoscopes

179

Operating Laryngoscopes

DEDO-PILLING MICRO LARYNGOSCOPE TYPE II
• Eliminates light loss though continuous illuminating fibers
• Supplied with two light carriers

Number Size

Overal
length

Minimum Maximum
ID
OD

Description

L530-173

173 mm

11.6 mm

Dedo-Pilling Micro Laryngoscope
Type II

Adult

30.1 mm

HOLINGER LARYNGOSCOPE
Number

Description

Working Length

Full Length

L740020

Adult Large

157 mm

180 mm

L550-1350

Adult Medium

146 mm

170 mm

JACKSON LARYNGOSCOPE
Number

Description

Full Length

L740012

Infant Laryngoscope

120 mm

L740017

Child Laryngoscope

170 mm

L740018

Adult Laryngoscope

180 mm

LAR INS

FIBER OPTIC LIGHT CARRIERS
Number

Description

Compatible Laryngoscope Models

L30010

Large, Fiber Optic Light Carrier

Kleinsassar Type L30001 - L30005

L30011

Medium, Fiber Optic Light Carrier

Kleinsassar Type L30006 - L30007

L30012

X-Long, Fiber Optic Light Carrier

Kleinsassar Type L30005

L30013

Light carrier fittings - Storz

L30014

Light carrier fittings - Wolfe

L550-1330

Fiber Optic Light Carrier with clip for proximal illumination

SUCTIONS

180

Number

Description

Compatible Laryngoscope Models

L30110

Suction / Smoke Evacuator

Kleinsassar Type L30001 - L30005

L30111

Suction / Smoke Evacuator

Kleinsassar Type L30006 - L30007

Micro Scissors and Forceps

ROTATING FORCEPS AND SCISSORS
• Full 360° rotation through finger post facilitates
• Double action jaws
• Working Length: 22 cm
Forceps

Number Description
L32203

Cutting Forceps with round cupped double action jaws

2 mm Ø

curved

L32206

Alligator Forceps with serrated, double action jaws

curved

L32207

Grasping Forceps with triangular, serrated, double action jaws

curved upwards

Scissors

Number Description
L32210

Scissors

curved

ANTERIOR COMMISSURE FORCEPS AND SCISSORS
• Conical sheath for high stability and optimal view
• Optimum access in the anterior commissure via 10° upcurved distal end
Cutting Forceps

Number Description
Cutting Forceps with round, cupped jaws

2 mm Ø

straight

L32102

Cutting Forceps with round, cupped jaws

2 mm Ø

curved upwards

L32103

Cutting Forceps with round, cupped jaws

2 mm Ø

curved right

L32104

Cutting Forceps with round, cupped jaws

2 mm Ø

curved left

LAR INS

L32101

Scissors

Number Description
L32108

Scissors

straight

L32109

Scissors

upcurved 45°

L32110

Scissors

curved right

L32111

Scissors

curved left

181

Micro Scissors and Forceps

CUTTING FORCEPS
• Conical sheath for high stability and optimal view
• Working length: 23 cm
Standard Model

Number Description
L32001

Cutting Forceps with round cupped jaws

2 mm Ø

straight

L32002

Cutting Forceps with round cupped jaws

2 mm Ø

curved upwards

L32003

Cutting Forceps with round cupped jaws

2 mm Ø

curved right

L32004

Cutting Forceps with round cupped jaws

2 mm Ø

curved left

L32050

Cutting Forceps with round cupped jaws

2 mm Ø

curved upwards right

L32051

Cutting Forceps with round cupped jaws

2 mm Ø

curved upwards left

L32052

Cutting Forceps with round cupped jaws, horizontal opening

2 mm Ø

curved right

L32053

Cutting Forceps with round cupped jaws, horizontal opening

2 mm Ø

curved left

L32150

Cutting Forceps with long oval cupped jaws

curved upwards

L32151

Cutting Forceps with long oval cupped jaws, opening right

upcurved

L32152

Cutting Forceps with long oval cupped jaws, opening left

upcurved

Heavy Model

Number Description
L32040

Forceps with oval cupped jaws

3x5 mm

straight

L32041

Forceps with round cupped jaws

4 mm Ø

straight

L32042

Forceps with round cupped jaws

4 mm Ø

curved upwards

L32043

Forceps with round cupped jaws

4 mm Ø

curved right

L32044

Forceps with round cupped jaws

4 mm Ø

curved left

Double Action Model

Number Description

LAR INS

L32046

Cutting Forceps with round cupped, double action jaws

5 mm Ø

straight

Minature, Very Delicate Model

Number

Description

L32060

Miniature Cutting Forceps with cupped jaws

1 mm Ø

straight

L32061

Miniature Cutting Forceps with cupped jaws

1 mm Ø

curved upwards

L32062

Miniature Cutting Forceps with cupped jaws

1 mm Ø

curved right

L32063

Miniature Cutting Forceps with cupped jaws

1 mm Ø

curved left

L32064

Miniature Cutting Forceps with cupped jaws

1 mm Ø

curved upwards right

182 L 32065

Miniature Cutting Forceps with cupped jaws

1 mm Ø

curved upwards left

Micro Scissors and Forceps

GRASPING FORCEPS
• Conical sheath for high stability and optimal view
• Working length: 23 cm
Standard Model

Number Description
L32105

Artery Forceps with ratchet

serrated

straight

L32005

Alligator Forceps

serrated

straight

L32006

Alligator Forceps

serrated

curved right

L32007

Alligator Forceps

serrated

curved left

L32215

Alligator Forceps, horizontal opening

serrated

straight

L32054

Alligator Forceps

serrated

curved up

L32154

Alligator Forceps, horizontal opening

serrated

curved up

L32055

Forceps with triangular jaws

curved up

opening right

L32056

Forceps with triangular jaws

curved up

opening left

L32058

Forceps with triangular jaws

straight

L32059

Forceps with triangular jaws

curved up

L32068

ARNOLD Vocal Cord Holding Forceps with triangular jaws

for right side

L32069

ARNOLD Vocal Cord Holding Forceps with triangular jaws

for left side

Minature, Very Delicate Model

Number Description
Miniature Grasping Forceps

serrated

straight

L32071

Miniature Grasping Forceps

serrated

curved upwards

L32072

Miniature Grasping Forceps

serrated

curved right

L32073

Miniature Grasping Forceps

serrated

curved left

L32076

Miniature Grasping Forceps with triangular jaws

serrated

curved right

L32077

Miniature Grasping Forceps with triangular jaws

serrated

curved left

LAR INS

L32070

183

Micro Scissors and Forceps

SCISSORS
• Conical sheath for high stability and optimal view
• Working length: 23 cm
Standard Model

Number Description
L32008

Scissors

straight

L32009

Scissors

curved up 45°

L32115

Scissors

curved up 15°

L32010

Scissors

curved right

L32011

Scissors

curved left

L32057

Scissors, horizontal cutting

straight

Minature, Very Delicate Model

LAR INS

Number Description

184

L32080

Miniature Scissors

straight

L32081

Miniature Scissors

curved up 45°

L32082

Miniature Scissors

curved right

L32083

Miniature scissors

curved left

Micro Scissors and Forceps

PEDIATRIC FORCEPS AND SCISSORs
• Conical sheath for high stability and optimal view
• Working length: 18 cm
Cutting Forceps

Number Description
L31902

Cutting Forceps with cupped jaws

2 mm Ø

straight

L31903

Cutting Forceps with cupped jaws

2 mm Ø

curved up

L31904

Cutting Forceps with cupped jaws

3 mm Ø

straight

L31905

Cutting Forceps with cupped jaws

3 mm Ø

curved up

L31906

Cutting Forceps with cupped jaws

1 mm Ø

straight

L31907

Cutting Forceps with cupped jaws

1 mm Ø

curved up

L31930

Cutting Forceps with cupped jaws with
horizontal opening and malleable distal
end

4 mm Ø

Grasping Forceps

L31910

Alligator Forceps with serrated jaws

straight

Scissors

Number Description
L31920

Scissors

straight

L31921

Scissors

upcurved 45°

L31922

Scissors

curved right

L31923

Scissors

curved left

LAR INS

185

Micro Scissors and Forceps

UNIPOLAR COAGULATION FORCEPS
• Unipolar coagulation
• 360° rotatable
• Laser smoke evacuation

LAR INS

Number Description

186

Shaft

Working
Length

L040023

Unipolar coagulation forceps with smoke
evacuation channel

Rotatable

Serrated

Straight

3.0 mm

23 cm

L040223

Unipolar coagulation forceps with smoke
evacuation channel

Rotatable

Serrated

Straight

3.0 mm

23 cm

L040423

Unipolar coagulation forceps with smoke
evacuation channel

Rotatable

Serrated

Straight

3.0 mm

23 cm

L040623

Unipolar coagulation forceps with smoke
evacuation channel

Rotatable

Serrated

Straight

3.0 mm

23 cm

Micro Scissors and Forceps

• Concial sheath for high stability and optimal view

Number Description

Working Length

L32036

23 cm

Needle Holder with ratchet, conical sheath

NEEDLE HOLDER FOR ENDO-LARYNGOSCOPY
• Concial sheath fo rhigh stability and optimal view

Number Description
L32037

Needle holder with ratchet, delicate
with rounded, serrated jaws

Working Length
1.6 mm Ø

upcurved

23 cm

LAR INS

187

Micro Knives and Elevators

MICROSURGERY INSTRUMENTS
Number Description
L32025

Handle for use with L32013-L32116

Number Description
L32013

Knife

Round

45 ° angle

L32014

Knife

Round

Verticle cutting

L32015

Knife

Oval

Straight

L32016

Knife

L32116

Knife

Sickle shaped

L32017

Knife

Golf club shaped

L32018

Hook

Blunt

L32019

Hook

Sharp

L32024

Hook

Probe end

L32020

Needle

Curved right

L32021

Needle

Curved left

L32022

Elevator with suction channel

L32023

Knot Tier

Straight cutting
Curved

90° angle

JAKO ENDOLARYNGEAL MICROSURGERY
LAR INS

Number Description

188

L44510

JAKO Laryngeal Sickle Knife

Knife length: 8 mm

L44511

JAKO Laryngeal Knife

Knife length: 8 mm

L44520

JAKO Laryngeal Probe

L44521

JAKO Laryngeal Hook

L44540

JAKO Laryngeal Dissector

Blunt

2.5 mm Ø

Micro Knives and Elevators

MICRO LARYNGEAL BLADE HANDLE
• Collet designed to hold sterile micro blades

Number Description

Working length

Wing dimension

65-44300

22.5 cm

42 x 25 mm

Harris MicroLaryngeal blade handle*

Number Description
60-44030

Microblade

Sterile

6/box

* Designed in conjunction with Thomas Harris MA FRCS. London, UK.

LAR INS

189

Micro Suctions

UPCURVED BALL TIP SUCTION
Number Description

Outer Ø

Working Length

L32029

Suction Tube with distal end upcurved

Tip ball shape

2 mm

25 cm

L32039

Suction Tube with distal end upcurved

Tip ball Shape

3 mm

25 cm

Number Description

Outer Ø

Working Length

L31932

Pediatric Suction Tube with ball end

2 mm

20 cm

L31933

Pediatric Suction Tube with ball end

3 mm

20 cm

PEDIATRIC SUCTION

LAR INS

STRAIGHT SUCTION
Number Description

Outer Ø

Working Length

L32026

Suction Tube

2 mm

25 cm

L32027

Suction Tube

2.5 mm

25 cm

L32028

Suction Tube

3 mm

25

INSULATED CANNULA

190

Number Description

Outer Ø

L32030

3 mm

Insulated Cannula for suction and coagulation

Micro Suctions

COTTON CARRIER
Number Description
L32128

Cotton Carrier

Twist end serrated

Working Length

Outer Ø

28 cm

2.5 mm

ASPIRATION TUBE
Working
Length

Number Description
L32220

Aspiration Tube with smooth oval shaped opening
on each side of the velvet tip

Closed, blunt end

3 mm Ø

22 cm

L32221

Aspiration Tube with smooth oval shaped opening
on each side of the velvet tip

Closed, blunt end

4 mm Ø

22 cm

LAR INS

191

LAR INS

Micro Injection Needles

192

Number

Description

L32130

Injection Needle

Number

Description

L32131

Injection Needle

Working Length
Luer-Lock

Bayonet shaped

23 cm

Working Length
Luer-Lock

Curved

23 cm

Laser Suctions

SUCTION WITH LASER PROTECTOR
• Special black finish protects lower regions of the mucous membrane against laserbeam

Working
Length

Number Description
Suction Tube with laser-protector and smoke
evacuation channel

Black

Round

Upcurved

3 mm Ø

23 cm

L41004

Suction Tube with laser-protector and smoke
evacuation channel

Black

Round

Upcurved

4 mm Ø

23 cm

L41005

Suction Tube with laser-protector and smoke
evacuation channel

Black

Round

Upcurved

5 mm Ø

23 cm

L41007

Suction Tube with laser-protector and smoke
evacuation channel

Black

Oval

Upcurved

7 mm Ø

23 cm

L41009

Suction Tube with laser-protector and smoke
evacuation channel, distal suction hole left side

Black

Oval

Straight

23 cm

L41010

Suction Tube with laser-protector and smoke
evacuation channel, distal suction hole right side

Black

Oval

Straight

23 cm

L41011

Suction Tube with laser-protector and smoke
evacuation channel, distal suction hole left side

Black

Corner Shaped

23 cm

L41012

Suction Tube with laser-protector and smoke
evacuation channel, distal suction hole right side

Black

Corner Shaped

23 cm

L41013

Suction Tube with laser-protector and smoke
evacuation channel, distal suction hole left side

Black

Bayonet Shaped

23 cm

L41014

Suction Tube with laser-protector and smoke
evacuation channel, distal suction hole left side

Black

Bayonet Shaped

23cm

L41016

Suction Tube with laser-protector and smoke
evacuation channel for larynx and trachea

Black

Upcurved

10x10 mm

26 cm

L41017

Suction Tube with laser-protector and smoke
evacuation channel for hypopharyngeal
diverticulum, slightly upcurved and 7 mm wide

Black

Upcurved

10x10 mm

23cm

LAR INS

L41003

193

Laser Suctions

SUCTION TUBE WITH INTERRUPTION
• Special black finish protects lower regions of the mucous membrane against laserbeam

Number Description

Working Length

L41025

Suction Tube with interruption

Black

2.5 mm Ø

23 cm

L41030

Suction Tube with interruption

Black

3 mm Ø

23 cm

ASPIRATION TUBE
• Special black finish protects lower regions of the mucous membrane against laserbeam

Working
Length

Number Description
L41033

Aspiration Tube with smooth oval shaped opening
on each side of velvet tip

Black

Closed, blunt end

3 mm Ø

22 cm

INSULATED SUCTION
Number Description
Insulated Suction and coagulation cannula

Unipolar

3 mm Ø

23 cm

LAR INS

L41130

Working Length

INSULATED SUCTION
Number Description

194

Outer Ø

Working Length

L41225

Suction Tube

Insulated

Ball end

2.5 mm

30 cm

L41230

Suction Tube

Insulated

Ball end

3 mm

30 cm

Broncho-Esophagoscopic Forceps

JACKSON BRONCHO-ESOPHAGOSCOPIC FORCEPS
Single Action Jaws

shaft Length
30 cm

L31304

L31305

L31306

2 mm Ø

4 mm Ø

L31312

L31313

40 cm

L31404

L31405

L31406

L31412

L31413

50 cm

L31504

L31505

L31506

L31512

L31513

60 cm

L31604

L31605

L31606

L31612

L31613

shaft Length

2 mm Ø

4 mm Ø

30 cm

L31317

L31319

L31320

L31331

L31335

40 cm

L31417

L31419

L31420

L31431

L31435

50 cm

L31517

L31519

L31520

L31531

L31535

60 cm

L31617

L31619

L31620

L31631

L31635

Double Action Jaws

30 cm

L32304

L32306

L32314

L32320

L31331

L32335

40 cm

L32404

L32406

L32414

L32420

L32431

L32435

50 cm

L32504

L32506

L32514

L32520

L32531

L32535

60 cm

L32604

L32606

L32614

L32620

L32631

L32635

LAR INS

shaft Length

195

Broncho-Esophagoscopic Forceps

LARYNGO- BRONCHO-ESOPHAGOSCOPIC FORCEPS

shaft Length
40 cm

L40850

L40862

L40864

L40866

L40876

50 cm

L50850

L50862

L50864

L50866

L50876

60 cm

L60850

L60862

L60864

L60866

L60876

40 cm

L40878

L40879

L40882

L40884

L40890

50 cm

L50878

L50879

L50882

L50884

L50890

60 cm

L60878

L60879

L60882

L60884

L60890

40 cm

L40892

L40894

L40896

50 cm

L50892

L50894

L50896

60 cm

L60892

L60894

L60896

shaft Length

shaft Length

Child Sizes

LAR INS

shaft Length
35 cm

L35710

L35730

L35794

L35796

L35732

L35790

L35792

L35814

L35816

shaft Length
35 cm

196

L35812

L35793

Broncho-Esophagoscopic Forceps

BRONCHO-ESOPHAGOSCOPIC FORCEPS
• Double action jaws

shaft Length

1.5 mm Ø

1.5 mm Ø

1.5mm Ø

1.5 mm Ø

25 cm

L85125

L85225

L85325

L85425

35 cm

L85135

L85235

L85335

L85435

shaft Length

2.0 mm Ø

2.0 mm Ø

2.0 mm Ø

2.0 mm Ø

35 cm

L85140

L85240

L85340

L85440

shaft Length

2.5 mm Ø

2.5 mm Ø

2.5 mm Ø

2.5 mm Ø

55 cm

L85150

L85250

L85350

L85450

FOREIGN BODY FORCEPS
• Strong model for excellent cutting and grasping performance
• Cuts up to 1.2mm Ø wires

2.5 mm Ø

35 cm

L85535

45 cm

L85545

LAR INS

shaft Length

197

Broncho-Esophagoscopic Forceps

FLEXIBLE ENDOSCOPY
• Stainless steel
• Spiral of highest flexibility
• Solidly constructed handles
• Autoclavable by all the conventional methods

Serrated

90 cm

120 cm

150 cm

180 cm

230 cm

1.8 mm Ø

L47005

L47025

L47055

L47085

L47095

2.3 mm Ø

L47007

L47027

L47057

L47087

L47097

90 cm

120 cm

150 cm

180 cm

230 cm

1.8 mm Ø

L47205

L47225

L47255

L47285

L47295

2.3 mm Ø

L47207

L47227

L47257

L47287

L47297

90 cm

120 cm

150 cm

180 cm

230 cm

1.8 mm Ø

L47305

L47325

L47355

L47385

L47395

2.3 mm Ø

L47307

L47327

L47357

L47387

L47397

90 cm

120 cm

150 cm

180 cm

230 cm

1.8 mm Ø

L47605

L47625

L47655

L47685

L47695

2.3 mm Ø

L47607

L47627

L47657

L47687

L47697

90 cm

120 cm

150 cm

180 cm

230 cm

1.8 mm Ø

L47805

L47825

L47855

L47885

L47895

2.3 mm Ø

L47807

L47827

L47857

L47887

L47897

2x2 Teeth

Three Clawed

1x2 Teeth

Pike Teeth

Serrated Cup Jaws

90 cm

120 cm

150 cm

180 cm

230 cm

1.8 mm Ø

L47905

L47925

L47955

L47985

L47995

2.3 mm Ø

L47907

L47927

L47957

L47987

L47997

Round Cup Jaws

90 cm

120 cm

150 cm

180 cm

230 cm

1.8 mm Ø

L48005

L48025

L48055

L48085

L48095

2.3 mm Ø

L48007

L48027

L48057

L48087

L48097

90 cm

120 cm

150 cm

180 cm

230 cm

2.3 mm Ø

L48107

L48127

L48157

L48187

L48197

Oval Cup Jaws

90 cm

120 cm

150 cm

180 cm

230 cm

1.8 mm Ø

L48205

L48225

L48255

L48285

L48295

2.3 mm Ø

L48207

L48227

L48257

L48287

L48297

Oval Cup Jaws
with Pin

90 cm

120 cm

150 cm

180 cm

230 cm

2.3 mm Ø

L48307

L48327

L48357

L48387

L48397

90 cm

120 cm

150 cm

180 cm

230 cm

L48807

L48827

L48857

L48887

L48897

LAR INS

Round Cup Jaws
with Pin

1 Blade Serrated

198

2.3 mm Ø

Broncho-Esophagoscopic Suctions

Number Description

Working Length

L18035

Rigid Suction Tube

2.5 mm Ø

25 cm

L18050

Rigid Suction Tube

4 mm Ø

50 cm

Number Description

Working Length

L18135

Rigid Suction Tube with flexible rubber tip

35 cm

L18150

Rigid Suction Tube with flexible rubber tip

50 cm

LAR INS

199

Accessories

COTTON CARRIERS
Number Description

Working Length

L18335

Cotton Carrier

35 cm

L18350

Cotton Carrier

50 cm

SPONGE HOLDER
Number Description
L18440

Sponge Holder

Working Length
1 x 2 teeth

38 cm

TEETH PROTECTORS
• Can also be used as inlet for metal teeth protector (non-autoclavable)

Number Description

LAR INS

L96050

200

Plastic Teeth Protector

R&CS ACC

DIS

OTO ACC

OSS
LAR ACC

SPE ACC

RHI INS

PSB

OTO INS

INSTRUMENTS

LAR INS

ORO-NASOPHARYNGEAL

ORO/NAS INS

Adenotomes

LA FORCE ADENOTOME
Number Description

Working Length

L11110

Adenotome by La Force

Size 0

23.5 cm

L11111

Adenotome by La Force

Size 1

23.5 cm

L11112

Adenotome by La Force

Size 2

23.5 cm

L11113

Adenotome by La Force

Size 3

23.5 cm

SHAMBAUGH ADENOTOME
Number Description

Working Length

L11150

Adenotome by Shambaugh

Size 0

23.5 cm

L11151

Adenotome by Shambaugh

Size 1

23.5 cm

L11152

Adenotome by Shambaugh

Size 2

23.5 cm

L11153

Adenotome by Shambaugh

Size 3

23.5 cm

ADENOTOME REPLACEMENT BLADES
Number Description

Length

L11190

Replacement blades

Size 0

10mm

L11191

Replacement blades

Size 1

13 mm

L11192

Replacement blades

Size 2

16 mm

L11193

Replacement blades

Size 3

19 mm

203

Currettes

BECKMANN ADENOID CURRETTE
Number Description

Blade
Width

Overall
Length

L40200

Reverse Curve Curette

Size 0

Straight

10.5 mm

22 cm

L40201

Reverse Curve Curette

Size 1

Straight

13 mm

22 cm

L40202

Reverse Curve Curette

Size 2

Straight

14.5 mm

22 cm

L40203

Reverse Curve Curette

Size 3

Straight

16 mm

22 cm

L40204

Reverse Curve Curette

Size 4

Straight

18 mm

22 cm

L40205

Reverse Curve Curette

Size 5

Straight

20.5 mm

22 cm

Number Description

Blade
Width

Overall
Length

L13460

Reverse Curve Curette with basket

Size 1

Straight

10 mm

22 cm

L13461

Reverse Curve Curette with basket

Size 2

Straight

11 mm

22 cm

L13462

Reverse Curve Curette with basket

Size 3

Straight

12 mm

22 cm

L13463

Reverse Curve Curette with basket

Size 4

Straight

13 mm

22 cm

L13465

Reverse Curve Curette with basket

Size 5

Straight

15 mm

22 cm

L13466

Reverse Curve Curette with basket

Size 6

Straight

16 mm

22 cm

SHAMBAUGH ADENOID CURRETTE
Number Description

204

Blade
Width

Overall
Length

L14710

Adenoid Curette

Size 0

Curved backwards

10 mm

22 cm

L14712

Adenoid Curette

Size 2

Curved backwards

12 mm

22 cm

L14714

Adenoid Curette

Size 3

Curved backwards

13 mm

22 cm

L14716

Adenoid Curette

Size 4

Curved backwards

15 mm

22 cm

L14718

Adenoid Curette

Size 5

Curved backwards

16 mm

22 cm

Adenoid Currettes

ST. CLAIR-THOMSON ADENOID CURRETTE
Number Description

Blade
Width

Overall
Length

L40300

Reverse Curve Curette with basket

Size 0

Straight

10.5 mm

22 cm

L40301

Reverse Curve Curette with basket

Size 1

Straight

13 mm

22 cm

L40302

Reverse Curve Curette with basket

Size 2

Straight

14.5 mm

22 cm

L40303

Reverse Curve Curette with basket

Size 3

Straight

16.5 mm

22 cm

L40304

Reverse Curve Curette with basket

Size 4

Straight

18 mm

22 cm

L40305

Reverse Curve Curette with basket

Size 5

Straight

20.5 mm

22 cm

BARNHILL ADENOID CURRETTE
Number Description

Blade
Width

Overall
Length

L40400

Adenoid Curette

Size 0

Curved

10.5 mm

21.5 cm

L40401

Adenoid Curette

Size 1

Curved

13 mm

21.5 cm

L40402

Adenoid Curette

Size 2

Curved

14.5 mm

21.5 cm

L40403

Adenoid Curette

Size 3

Curved

16.5 mm

21.5 cm

L40404

Adenoid Curette

Size 4

Curved

18 mm

21.5 cm

JONES ADENOID CURRETTE
Number Description

Blade
Width

Overall
Length

L40701

Adenoid Curette

Infant

Straight

4 mm

22.5 cm

L40702

Adenoid Curette

Child

Straight

6 mm

22.5 cm

L40703

Adenoid Curette

Adult

Straight

8 mm

22.5 cm

VOGEL ADENOID CURRETTE
Number Description
L40800

Adenoid Curette

Infant

Curved

9 x 12 mm

Blade
Width

Overall
Length

7 mm

21.5 cm

205

Adenoid Currettes

MIDDLETON ADENOID CURRETTE
Number Description
L40850

Long and Narrow Adenoid Curette

25 x 10 mm

Blade
Width

Overall
Length

7 mm

22.5 cm

STUBBS ADENOID CURRETTE
Number Description
L40900

Adenoid Curette with angulated shaft

Size 0

Curved

Blade
Width

Overall
Length

11 mm

22 cm

L40901

Adenoid Curette with angulated shaft

Size 1

Curved

14 mm

22 cm

L40902

Adenoid Curette with angulated shaft

Size 2

Curved

16 mm

22 cm

L40903

Adenoid Curette with angulated shaft

Size 3

Curved

18 mm

22 cm

BECKMANN DISPOSIBLE ADENOID CURRETTE
• Sterile

Number Description

206

Blade
Width

Overall
Length

25-2110

Adenoid Curette without basket

Size 1

Straight

10 mm

22 cm

25-2120

Adenoid Curette without basket

Size 2

Straight

11 mm

22 cm

25-2130

Adenoid Curette without basket

Size 3

Straight

12 mm

22 cm

25-2140

Adenoid Curette without basket

Size 4

Straight

13 mm

22 cm

Mirrors

LARYNGEAL MIRROR ON HANDLE
• Autoclavable
• Stainless Steel

Number Description

Size

Diameter

L34806

Mirror attached on handle

000

6 mm

L34808

Mirror attached on handle

00

8 mm

L34810

Mirror attached on handle

0

10 mm

L34812

Mirror attached on handle

1

12 mm

L34814

Mirror attached on handle

2

14 mm

L34816

Mirror attached on handle

3

16 mm

L34818

Mirror attached on handle

4

18 mm

L34820

Mirror attached on handle

5

20 mm

L34822

Mirror attached on handle

6

22 mm

L34824

Mirror attached on handle

7

24 mm

L34826

Mirror attached on handle

8

26 mm

L34828

Mirror attached on handle

9

28 mm

L34830

Mirror attached on handle

10

30 mm

LARYNGEAL MIRROR AND HANDLE
• Autoclavable
• Stainless Steel
• For use with octagonal handle L53700

Size

Diameter

L53620

Number Description
Mirror with threaded shaft

00

8 mm

L53600

Mirror with threaded shaft

0

10 mm

L53601

Mirror with threaded shaft

1

12 mm

L53602

Mirror with threaded shaft

2

14 mm

L53603

Mirror with threaded shaft

3

16 mm

L53604

Mirror with threaded shaft

4

18 mm

L53605

Mirror with threaded shaft

5

20 mm

L53606

Mirror with threaded shaft

6

22 mm

L53607

Mirror with threaded shaft

7

24 mm

L53608

Mirror with threaded shaft

8

26 mm

L53609

Mirror with threaded shaft

9

28 mm

L53610

Mirror with threaded shaft

10

30 mm

Number Description
L53700

Octagonal mirror handle
For use with mirrors L53600-L53620

Overall Length
75 mm

207

Mirrors

RHODIUM LARYNGEAL MIRROR AND HANDLE
• Autoclavable
• Stainless Steel
• For use with octagonal handle L54100

Number Description

Size

Diameter

L54320

Rhodium plated mirror with standard shaft

00

8 mm

L54300

Rhodium plated mirror with standard shaft

0

10 mm

L54301

Rhodium plated mirror with standard shaft

1

12 mm

L54302

Rhodium plated mirror with standard shaft

2

14 mm

L54303

Rhodium plated mirror with standard shaft

3

16 mm

L54304

Rhodium plated mirror with standard shaft

4

18 mm

L54305

Rhodium plated mirror with standard shaft

5

20 mm

L54306

Rhodium plated mirror with standard shaft

6

22 mm

L54307

Rhodium plated mirror with standard shaft

7

24 mm

L54308

Rhodium plated mirror with standard shaft

8

26 mm

L54309

Rhodium plated mirror with standard shaft

9

28 mm

L54310

Rhodium plated mirror with standard shaft

10

30 mm

Number Description
L54100

Overall Length

Octagonal, stainless steel mirror handle
For use with mirrors L53600-L54320

75 mm

MICHEL RHINOSCOPIC MIRROR WITH HANDLE
• Autoclavable
• Stainless Steel
• Thumb mirror orientation control

Number Description

Size

Diameter

Length

L54110

Michel Mirror with handle

0

10 mm

29 mm

L54112

Michel Mirror with handle

1

12 mm

29 mm

L54114

Michel Mirror with handle

2

14 mm

29 mm

L54116

Michel Mirror with handle

3

16 mm

29 mm

L54118

Michel Mirror with handle

4

18 mm

29 mm

Spare Mirrors for Michel Rhinoscopic Mirror with Handle

Number Description

208

Size

Diameter

L54120

Spare Mirror for Michel Rhinoscopic Mirrors

0

10 mm

L54122

Spare Mirror for Michel Rhinoscopic Mirrors

1

12 mm

L54124

Spare Mirror for Michel Rhinoscopic Mirrors

2

14 mm

L54126

Spare Mirror for Michel Rhinoscopic Mirrors

3

16 mm

L54128

Spare Mirror for Michel Rhinoscopic Mirrors

4

18 mm

Mouth Gags - Tongue Depressors

JENNINGS MOUTH GAG
• Stainless Steel

Number Description

Working Length

N20009

Mouth Gag by Jennings

Open type

9 cm

N20011

Mouth Gag by Jennings

Open type

11 cm

N20013

Mouth Gag by Jennings

Open type

13 cm

Number Description

Working Length

N23009

Mouth Gag by Jennings

Standard type

9 cm

N23011

Mouth Gag by Jennings

Standard type

11 cm

N23013

Mouth Gag by Jennings

Standard type

13 cm

N23015

Mouth Gag by Jennings

Standard type

15 cm

HEISTER MOUTH GAG
Number Description

Working Length

N20505

13 cm

Mouth Gag by Heister

MOLT MOUTH GAG
Number Description

Working Length

N20510

Mouth Gag by Molt

Child Size

10 cm

N20515

Mouth Gag by Molt

Adult Size

15 cm

ROSER KÖNIG MOUTH GAG
Number Description

Working Length

N20545

16 cm

Mouth Gag by Roser König

DENHART MOUTH GAG
Number Description

Working Length

N20560

13 cm

Mouth Gag by Denhart

209

Mouth Gags - Tongue Depressors

WHITEHEAD MOUTH GAG
Number Description

Working Length

N20729

Mouth Gag by Whitehead

9 cm

N20731

Mouth Gag by Whitehead

11 cm

N20733

Mouth Gag by Whitehead

13 cm

N20735

Mouth Gag by Whitehead

15 cm

DINGMAN MOUTH GAG
• Stainless Steel

Number Description
N20800

Dingman Mouth Gag Complete Set including:
Frame with 4 spiral springs for the suspension of the thread ends, 2 Movable Tooth
Hooks,
2 Cheek Retractors, and 3 Tongue Depressors (1 of each #1-3)

N20820

Dingman Mouth Gag Frame with 4 spiral springs for the suspension of the thread ends,
2 Movable Tooth Hooks and 2 Cheek Retractors

DINGMAN TONGUE DEPRESSORS
Number Description
N20811

Tongue Depressor

Size 1

55 x 25 mm

N20812

Tongue Depressor

Size 2

60 x 27 mm

N20813

Tongue Depressor

Size 3

70 x 30 mm

SEEMANN-SEIFFERT MOUTH GAG
• Stainless Steel

Working
Length

Number Description

210

N22009

Self retaining Mouth Gag by Seemann-Seiffert

Small / Child Size

9 cm

N22011

Self retaining Mouth Gag by Seemann-Seiffert

Standard Size

11 cm

N22013

Self retaining Mouth Gag by Seemann-Seiffert

Large Size

13 cm

N20755

Self retaining Mouth Gag by Seemann-Seiffert

X-Large Size

15 cm

Number Description

Working Length

N24011

Standard Model Mouth Gag by Seemann-Seiffert

11 cm

N24013

Standard Model Mouth Gag by Seemann-Seiffert

13 cm

Mouth Gags - Tongue Depressors

DAVIS-BOYLE MOUTH GAG
• Stainless Steel

Number Description
N26000

Left frame for Mouth Gag by Davis-Boyle

N26200

Right Frame for Mouth Gag by Davis-Boyle

N26300

Left frame for Mouth Gag by Davis-Boyle

Child size

Number Description
N26010

Silicone Bit Liners

Removable for Davis-Boyle

Autoclavable

(Sold in pairs)

DAVIS-BOYLE TONGUE DEPRESSOR
• Stainless Steel

Number Description

Length

N26001

Tongue Depressor by Davis-Boyle with smooth blades

Size 1

20 x 30 mm

13.5 cm

N26002

Tongue Depressor by Davis-Boyle with smooth blades

Size 2

23 x 65 mm

13.5 cm

N26003

Tongue Depressor by Davis-Boyle with smooth blades

Size 3

24 x 80 mm

13.5 cm

N26004

Tongue Depressor by Davis-Boyle with smooth blades

Size 4

25 x 93 mm

13.5 cm

N26005

Tongue Depressor by Davis-Boyle with smooth blades

Size 5

26 x 108 mm 13.5 cm

Number Description

Length

N26102

Tongue Depressor by Davis-Boyle with anaesthetic tube
Size 2
and smooth blades

23 x 65 mm

13.5 cm

N26103

Tongue Depressor by Davis-Boyle with anaesthetic tube
Size 3
and smooth blades

24 x 80 mm

13.5 cm

N26104

Tongue Depressor by Davis-Boyle with anaesthetic tube
Size 4
and smooth blades

25 x 93 mm

13.5 cm

N26105

Tongue Depressor by Davis-Boyle with anaesthetic tube
Size 5
and smooth blades

26 x 108 mm

13.5 cm

Number Description

Length

N26301

Tongue Depressor by Davis-Boyle for Children with
smooth blades

Size 1

17 x 30 mm

9.8 cm

N26302

Tongue Depressor by Davis-Boyle for Children with
smooth blades

Size 2

19 x 45 mm

9.8 cm

N26303

Tongue Depressor by Davis-Boyle for Children with
smooth blades

Size 3

20 x 60 mm

9.8 cm

N26304

Tongue Depressor by Davis-Boyle for Children with
smooth blades

Size 4

22 x 70 mm

9.8 cm

N26305

Tongue Depressor by Davis-Boyle for Children with
smooth blades

Size 5

22 x 80 mm

9.8 cm

211

Mouth Gags - Tongue Depressors

MCIVOR MOUTH GAG
• Stainless Steel

Number Description
N25000

Frame for Mouth Gag by McIvor for use with tongue depressors N25001 - N25003

Number Description

Rod Length

N25001

Tongue Depressor by McIvor

Size 1

23 x 70 mm

N25002

Tongue Depressor by McIvor

Size 2

25 x 86 mm

N25003

Tongue Depressor by McIvor

Size 3

26 x 100 mm

KILNER-DOUGHTY MOUTH GAG
• Stainless Steel

Number Description
N27000

Left frame for Mouth Gag by Kilner-Doughty

N27010

Palate Support for toothless patients for N27000

RUSSEL-DAVIS MOUTH TONGUE DEPRESSOR
• Stainless Steel

Number Description
N27001

Tongue Depressor by Russel-Davis with central channel

Size 1

28 x 65 mm

N27002

Tongue Depressor by Russel-Davis with central channel

Size 2

32 x 72 mm

N27003

Tongue Depressor by Russel-Davis with central channel

Size 3

37 x 80 mm

N27004

Tongue Depressor by Russel-Davis with central channel

Size 4

41 x 94 mm

N27005

Tongue Depressor by Russel-Davis with central channel

Size 5

46 x 103 mm

Number Description

212

N28601

Tongue Depressor by Russel-Davis with central channel and
lateral outlet

Size 1

28 x 65 mm

N28602

Tongue Depressor by Russel-Davis with central channel and
lateral outlet

Size 2

32 x 72 mm

N28603

Tongue Depressor by Russel-Davis with central channel and
lateral outlet

Size 3

37 x 80 mm

N28604

Tongue Depressor by Russel-Davis with central channel and
lateral outlet

Size 4

41 x 94 mm

N28605

Tongue Depressor by Russel-Davis with central channel and
lateral outlet

Size 5

46 x 103 mm

Mouth Gags - Tongue Depressors

WUERZBURG MODEL TONGUE DEPRESSOR
• Stainless Steel

Number Description
N28001

Wuerzburg Model Tongue Depressor

Size 1

28 x 66 mm

N28002

Wuerzburg Model Tongue Depressor

Size 2

32 x 75 mm

N28003

Wuerzburg Model Tongue Depressor

Size 3

34 x 83 mm

N28004

Wuerzburg Model Tongue Depressor

Size 4

37 x 93 mm

N28005

Wuerzburg Model Tongue Depressor

Size 5

38 x 100 mm

RING TONGUE DEPRESSOR
• Stainless Steel

Number Description
N28202
N28302

Left Ring Tongue Depressor
Right Ring Tongue Depressor

Size 2

23 x 58 mm

N28203
N28303

Left Ring Tongue Depressor
Right Ring Tongue Depressor

Size 3

27 x 72 mm

N28204
N28304

Left Ring Tongue Depressor
Right Ring Tongue Depressor

Size 4

34 x 87 mm

N28205
N28305

Left Ring Tongue Depressor
Right Ring Tongue Depressor

Size 5

37 x 95 mm

DAVIS-MEYER TONGUE DEPRESSOR
• Stainless Steel

Number Description
N28401

Tongue Depressor by Davis-Meyer with anesthetic
tubes on both sides

Size 1

29.0 x 70 mm

N28402

Tongue Depressor by Davis-Meyer with anesthetic
tubes on both sides

Size 2

30.5 x 75 mm

N28403

Tongue Depressor by Davis-Meyer with anesthetic
tubes on both sides

Size 3

31.5 x 80 mm

N28404

Tongue Depressor by Davis-Meyer with anesthetic
tubes on both sides

Size 4

32.5 x 85 mm

N28405

Tongue Depressor by Davis-Meyer with anesthetic
tubes on both sides

Size 5

33.5 x 95 mm

N28406

Tongue Depressor by Davis-Meyer with anesthetic
tubes on both sides

Size 6

33.8 x 100 mm

N28407

Tongue Depressor by Davis-Meyer with anesthetic
tubes on both sides

Size 7

34.0 x 105 mm

213

Mouth Gags - Tongue Depressors

DRAFFIN SUSPENSION APPARATUS BIPOD
Number Description
N24820

Suspension Apparatus Bipod by Draffin for use with Mouth Gags N25000 - N28400

N24810

Chain with ring to suspend the mouth gag at the frame N24880

NEGUS CHEST SUPPORT
Number Description

Rod Length

N29000

Chest Support by Negus with band N29001

Adult Size

14 cm

N29100

Chest Support by Negus with band N29001

Child Size

8.5 cm

N29001

Chest Support by Negus with band only for
N29000 & N29100

13 cm

WUERZURG CHEST SUPPORT
Number Description
N29200

Chest Support by Wuerzurg

TOOTH GUARD
Number Description
N20410

Wooden Tooth Guard

Diameter
Pyramid Shaped

Serrated

Number Description
N20420

Latex Tooth Guard

Diameter
Pyramid Shaped

Serrated

Number Description
N20450

214

40 mm

Latex Tooth Guard with Supply Chain

40 mm

Diameter
Grooved

40 mm

Mouth Gags - Tongue Depressors

MCKESSON MOUTH PROP
• Set of 2

N21001

Number Description
N21001

Silicone Mouth Prop with airway

Serrated

Small child

N21002

Silicone Mouth Prop with airway

Serrated

Child

N21003

Silicone Mouth Prop with airway

Serrated

Adult

N21002

N21003

215

Retractors

OBWEGESER RETRACTOR
Number Description
L20217

Obwegeser Cheek Retractor

Length
Stainless Steel

10 cm

UNIVERSITY OF MINNESOTA RETRACTOR
Number Description
L20210

University of Minnesota
Tongue and Cheek Retractor

Length
Stainless Steel

14 cm

STERNBERG RETRACTOR
Number Description
L20215

Sternberg Cheek, Lip and
Tongue Retractor

Length
Stainless Steel

14.5 cm

SHUMAN RETRACTOR
Number Description
L20225

Shuman Cheek and Tongue
Retractor

Length
Stainless Steel

RING RETRACTOR
Number Description
L20245

216

Cheek Ring Retractor

Stainless Steel

19 cm

Retractors

LOVE UVULA RETRACTOR
• Stainless Steel

Number Description

Width

Working Length

N16318

Love Uvula Retractor

18 mm

15 cm

N16320

Love Uvula Retractor

20 mm

15 cm

N16322

Love Uvula Retractor

22 mm

15 cm

GOODYEAR UVULA RETRACTOR
• Stainless Steel

Number Description

Width

Working Length

N16348

27 mm

9.5 cm

Goodyear Uvula Retractor

LOTHROP UVULA RETRACTOR
• Stainless Steel

Number Description

Width

Working Length

N16360

18 mm

18 cm

Lothrop Uvula Retractor

NAGER SOFT PALATE RETRACTOR
• Stainless Steel

Number Description

Width

Working Length

N16423

13 mm

22 cm

Nager Uvula Retractor

HOFER PALATE ARCH RETRACTOR
• Stainless Steel

Number Description
N16474

Hofer Palate Arch Retractor

Working Length
20 x 20 mm

24 cm

217

Retractors

HASLINGER SOFT PALATE RETRACTOR
• Stainless Steel

Number Description

Working Length

N16520

17 cm

Haslinger Soft Palate Retractor

YANKAUER NASO-PHARYNGEAL SPECULUM RETRACTOR
Number Description
N16570

218

Yankauer Naso-Pharyngeal Speculum Retractor

Tongue Spatulas

TONGUE SPATULA
• Stainless Steel

Number Description

Width

Working Length

N20010

18 mm

14.5 cm

Number Description

Width

Working Length

N20015

20 mm / 23 mm

14 cm

Tongue Spatula

Tongue Spatula

BAGINSKI TONGUE SPATULA
• Stainless Steel

Number Description

Width

Working Length

N20005

18 mm / 35 mm

15 cm

Baginski Tongue Spatula

BUCHWALD TONGUE SPATULA
• Stainless Steel

Number Description

Width

Working Length

N20018

18 mm / 23 mm

18 cm

Buchwald Tongue Spatula

HASLINGER TONGUE SPATULA
• Stainless Steel

Number Description

Width

Working Length

N20027

Haslinger Tongue Spatula

22 mm / 29 mm

12 cm

N20028

Haslinger Tongue Spatula

30 mm / 33 mm

16 cm

219

Tongue Spatulas

FRENZEL TONGUE SPATULA
• Stainless Steel

Number Description

Width

Working Length

N20035

23 mm / 13 mm

16.5 cm

Frenzel Tongue Spatula

BRÜNINGS TONGUE SPATULA
• Stainless Steel

Number Description

Width

Working Length

N20050

18 mm / 14 mm

19 cm

Brünings Tongue Spatula

MORITZ-SCHMIDT TONGUE SPATULA
• Stainless Steel

Number Description

Working Length

N20085

19 cm

Moritz-Schmidt Tongue Spatula

ANDREWS TONGUE SPATULA
• Stainless Steel

Number Description

Width

Working Length

N20130

17 mm

8.5 cm

Number Description

Width

Working Length

N20140

Wieder Tongue Spatula

28 mm

8 cm

N20141

Wieder Tongue Spatula

38 mm

8 cm

Andrews Tongue Spatula

WIEDER TONGUE SPATULA
• Stainless Steel

220

Tongue Spatulas

BOSWORTH TONGUE SPATULA
• Stainless Steel

Number Description

Width

Working Length

N20110

25 mm

8 cm

Number Description

Width

Working Length

N20115

25 mm

8 cm

Bosworth Tongue Spatula

TOBOLD TONGUE SPATULA
• Stainless Steel

Tobold Tongue Spatula

HARTMANN TONGUE SPATULA
• Stainless Steel

Number Description

Width

Working Length

N20125

23 mm

7.5 cm

Hartmann Tongue Spatula

FINGER GUARD
• Stainless Steel

Number Description

Diameter

N20101

Finger Guard #1

17 - 21 mm

N20102

Finger Guard #2

19 - 24 mm

N20103

Finger Guard #3

21 - 26 mm

221

Nasopharyngeal Forceps

RONIS BIOPSY FORCEPS
• Stainless Steel

Number Description

Size

Working Length

N02201

Biopsy forceps by Ronis

Upturned with triangular basket

1 = 7 mm

130 mm

M02202

Biopsy forceps by Ronis

Upturned with triangular asket

2 = 8 mm

130 mm

Size

Working Length

MELTZER ADENOID PUNCH
• Stainless Steel

Number Description
N02300

Adenoid punch by Meltzer

Straight with triangular basket

0 = 6 mm

140 mm

N02301

Adenoid punch by Meltzer

Straight with triangular basket

1 = 7 mm

140 mm

N02302

Adenoid punch by Meltzer

Straight with triangular basket

2 = 8 mm

140 mm

N02303

Adenoid punch by Meltzer

Straight with triangular basket

3 = 10 mm 140 mm

MELTZER ADENOID PUNCH
• Stainless Steel

Number Description

222

Size

Working Length

N02311

Adenoid punch by Meltzer

Straight with round basket

1 = 7 mm

140 mm

N02312

Adenoid punch by Meltzer

Straight with round basket

2 = 8 mm

140 mm

Nasopharyngeal Forceps

NASO-PHARYNGEAL BIOPSY FORCEPS
• Stainless Steel

Number Description
N15062

Naso-pharyngeal biospy forceps with malleable tip

Jaws open to the right

N15063

Naso-pharyngeal biospy forceps with malleable tip

Jaws open to the left

HARTMANN ADENOID PUNCH
• Stainless Steel

Number Description
N15212

Hartmann adenoid punch with basket

Working Length
Round

16.5 cm

SCHMEDEN ADENOID PUNCH
• Stainless Steel

Number Description
N15212

Shemeden adenoid punch with basket

Working Length
Triangular

16.5 cm

223

Nasopharyngeal Forceps

ST. CLAIR-THOMSON NASO-PHARYNGEAL FORCEPS
• Stainless Steel

Number Description
N15018

Working Length

St. Clair-Thomson Naso-Pharyngeal forceps

sharp

18 cm

JURASZ NASO-PHARYNGEAL FORCEPS
• Stainless Steel

Number Description
N15019

Working Length

Jurasz Naso-Pharyngeal forceps for children

sharp

19 cm

JATHO NASO-PHARYNGEAL FORCEPS
• Stainless Steel

Number Description
N15050

224

Jatho Naso-Pharyngeal forceps

Shaft Length
sharp

15 cm

Nasopharyngeal Forceps

JATHO EPIPHARYNGEAL FORCEPS
• Stainless Steel

Number Description

Working Length

N01500

Jatho Epipharyngeal forceps with
horizontal opening

Upturned with fenestrated
cupped jaws

15 cm

N01501

Jatho Epipharyngeal forceps with
vertical opening

Upturned with fenestrated
cupped jaws

15 cm

FRENZEL CONCHOTOME
• Stainless Steel

Number Description
N01600

Frenzel Conchotome for
adenotomies

Ring shaped jaws

Upturned

diameter

Working
Length

10 mm

14 cm

HARTMANN TONSIL PUNCH
• Stainless Steel

Number Description
N26513

Hartmann tonsil punch

Sharp

Diameter

Working Length

13 mm

12 cm

N26515

Hartmann tonsil punch

Sharp

15 mm

12 cm

N26517

Hartmann tonsil punch

Sharp

17 mm

12 cm

225

Tonsil Artery Forceps

NEGUS TONSIL ARTERY CLAMP
• Stainless Steel

Number Description

Size

Working Length

N24221

Negus tonsil artery clamp

1

19 cm

N24222

Negus tonsil artery Clamp with long curve

2

19 cm

MUCK TONSIL ARTERY CLAMP
• Stainless Steel

Number Description

Size

Tip

Working Length

N24281

Muck tonsil clamp

1

8 mm

18 cm

N24282

Muck tonsil clamp

2

10 mm

18 cm

MCWORTHER-LOTHROP TONSIL ARTERY CLAMP
• Stainless Steel

226

Number Description

Working Length

N24290

18.5 cm

McWorther-Lothrop tonsil artery clamp

Tonsil Artery Forceps

HEISS-BIRKETT TONSIL ARTERY CLAMP
• Stainless Steel

Number Description

Working Length

N50000

Heiss-Birkett tonsil artery clamp

Straight

Slender

20 cm

N50100

Heiss-Birkett tonsil artery clamp

Slightly curved

Slender

20 cm

SCHNIDT TONSIL ARTERY CLAMP
• Stainless Steel

Number Description

Working Length

N51000

Schnidt tonsil artery clamp

Slightly curved

Slender

19 cm

N51100

Schnidt tonsil artery clamp

Strong curved

Slender

19 cm

MIKULICZ TONSIL ARTERY CLAMP
• Stainless Steel

Number Description

Working Length

N24015

18 cm

Mikulicz tonsil artery clamp

227

Tonsil Seizing Forceps

MARSCHIK TONSIL FORCEPS
Number Description

Working Length

N24005

22 cm

Tonsil forceps by Marschik

WHITE TONSIL SEIZING FORCEPS
• Stainless Steel
• Open ring

Number Description

Working Length

N24018

Tonsil seizing forceps by White

18 cm

N24023

Tonsil seizing forceps by White

23 cm

COLVER TONSIL FORCEPS
Number Description

Working Length

N24019

19 cm

Tonsil forceps by Colver

BLOHMKE TONSIL SEIZING FORCEPS
• Stainless Steel
• Open ring

228

Number Description

Working Length

N24021

21 cm

Tonsil seizing forceps by Blohmke

Tonsil Seizing Forceps

ABRAHAM TONSIL FORCEPS
• Open ring

Number Description

Working Length

N24022

20.5 cm

Tonsil forceps by Tyding

THILENIUS TONSIL ABSCESS FORCEPS
• Stainless Steel

Number Description

Working Length

N24090

20 cm

Tonsil seizing forceps by Thilenius

TYDING TONSIL FORCEPS
• Open ring

Number Description
N36000

Tonsil forceps by Tyding

Working Length
2 x 2 teeth

21 cm

Tivnen Tonsil Forceps
Number Description
N36100

Tonsil forceps by Tivnen

Working Length
3 x 3 teeth

21 cm

229

Tonsil Knives

TONSIL KNIVES
Number Description

Working Length

N22005

18 cm

Tonsil knife

CANFIELD TONSIL KNIVES
Number Description

Working Length

N22030

21 cm

Canfield tonsil knife

ABRAHAM TONSIL KNIVES
Number Description

Working Length

N22035

21 cm

Abraham tonsil knife

BRÜNINGS TONSIL KNIVES
Number Description

Working Length

N22040

23 cm

Brünings tonsil knife

DAY TONSIL KNIVES

230

Number Description

Working Length

N22050

23 cm

Day tonsil knife

Tonsil Knives

ABRAHAM (TYDING) TONSIL KNIVES
Number Description

Working Length

N22055

20 cm

Abraham (Tyding) tonsil knife

FISHER (COLVER) TONSIL KNIVES
Number Description

Working Length

N22070

22.5 cm

Fisher (Colver) tonsil knife

231

Tonsil Screws

REVERSIBLE SCREWS

232

Number Description

Diameter

Working Length

N22085

Reversible screw

7 mm

21 cm

N22087

Reversible screw

4 mm

10 cm

Tonsil Dissectors

YANKAUER TONSIL DISSECTORS
• Stainless Steel

Number Description

Working Length

N22505

21 cm

Yankauer tonsil dissector

HURD TONSIL DISSECTORS
• Stainless Steel

Number Description

Size

Working Length

N22515

Hurd tonsil dissector

6 / 12 mm

22 cm

N22520

Hurd tonsil dissector

10 / 12 mm

22 cm

ALDERDICE TONSIL DISSECTORS
• Stainless Steel

Number Description

Working Length

N22530

22 cm

Alderdice tonsil dissector

HENKE TONSIL DISSECTORS
• Stainless Steel

Number Description

Size

Working Length

N22535

12 / 18 mm

24 cm

Henke tonsil dissector

233

Tonsil Dissectors

HENKE TONSIL DISSECTORS
Number Description

Size

Working Length

N22537

Henke tonsil dissector

12 mm

23 cm

N22538

Henke tonsil dissector

17 mm

23 cm

LOPEZ-REINKE TONSIL DISSECTORS
Number Description

Working Length

N02540

23 cm

Lopez-Reinke tonsil dissector with suction device

CARPENTER TONSIL DISSECTORS

234

Number Description

Working Length

N02540

25 cm

Carpenter tonsil dissector

Tonsil Scissors

METZENBAUM TONSIL SCISSORS
• Stainless Steel

Number Description

Working Length

N42018

Tonsil Scissors by Metzenbaum

Curved

18 cm

N42020

Tonsil Scissors by Metzenbaum

Curved

20 cm

N42218

Tonsil Scissors by Metzenbaum with tungsten carbide tip
and gold handles

Curved

18 cm

N42220

Tonsil Scissors by Metzenbaum with tungsten carbide tip
and gold handles

Curved

20.5 cm

LILLY TONSIL SCISSORS
• Stainless Steel

Number Description
N41400

Tonsil Scissors by Lilly

Working Length
Curved

19 cm

PRINCE TONSIL SCISSORS
• Stainless Steel

Number Description

Working Length

N24520

18 cm

Tonsil Scissors by Prince

BOETTCHER TONSIL SCISSORS
• Stainless Steel

Number Description

Working Length

N24525

18 cm

Tonsil Scissors by Boettcher

235

Tonsil Scissors

GOOD TONSIL SCISSORS
• Stainless Steel

Number Description

Working Length

N24530

19 cm

Tonsil Scissors by Good

DEAN TONSIL SCISSORS
• Stainless Steel

Number Description
N24550

236

Tonsil Scissors by Dean

Working Length
1 serrated blade

17 cm

Tonsil Snares

BRÜNINGS TONSIL SNARE
• Stainless Steel

Number Description
N25005

Tonsil snare with catch with Brünings
Includes 3 wire loops

Working Length
29 cm

EVES TONSIL SNARE
• Stainless Steel

Number Description
N25010

Tonsil snare by Eves
Includes 3 preshaped wires

Working Length
27 cm

EVES TONSIL SNARE
• Stainless Steel

Number Description

Working Length

N25011

27 cm

Tonsil snare with catch by Eves

LEWIS TONSIL SNARE
• Stainless Steel

Number Description
N25016

Tonsil snare by Lewis
Includes 3 preshaped wires

Working Length
25.5 cm

237

Tonsil Snares

ROEDER “E” TONSIL SNARE
• Stainless Steel

Number Description

Working Length

N25025

27 cm

Tonsil snare by Roeder “E” for catgut suture

TYDING TONSIL SNARE
• Stainless Steel

Number Description

238

Working Length

N25051

Tonsil Snare by Tyding with 3 preshaped wires

Straight tip

27 cm

N25052

Tonsil Snare by Tyding with 3 preshaped wires

Straight, Vedder
looped tip

27 cm

N25053

Straight tip only

N25054

Vedder loop tip only

Tonsil Snares

TONSIL SNARE WIRE LOOPS
Number Description
N25095

Soldered tonsil snare wire loops

100 / pack

TONSIL SNARE PRE-CUT WIRE
Number Description

Diameter

N25096

Pre-cut wire for tonsil snares

.35 mm

N25097

Pre-cut wire for tonsil snares

N25098

Pre-cut wire for tonsil snares

.45 mm

N25099

Pre-cut wire for tonsil snares

.50 mm

(Standard Size)

.40 mm

SNARE WIRES
Number Description

Diameter

N61543

Wire for snare

10 m coil

.35 mm

N61544

Wire for snare

10 m coil

.40 mm

N61545

Wire for snare

10 m coil

.45 mm

SNARE CATGUT SUTURE LOOPS
Number Description
N25025

Catugt suture loops for snares

Sterile

20 / box

N25030

Catugt suture loops for snares
Thickness 0

Sterile

20 / box

N25031

Catugt suture loops for snares
Thickness 1

Sterile

20 / box

239

Tonsiltome

SLUDER-BALLENGER TONSILTOME
• Stainless Steel handle

Number Description
N26010

Tonsiltome by Sluder-Ballenger, complete with one blade of each size
#1-3

N26019

Handle only for tonsiltome by Sluder-Ballenger

Angled-up blades

SLUDER-BALLENGER TONSILTOME BLADES

240

Number Description

Size

width

N26021

Blades for tonsiltome by Sluder-Ballenger

1

18 mm

N26022

Blades for tonsiltome by Sluder-Ballenger

2

20 mm

N26023

Blades for tonsiltome by Sluder-Ballenger

2

23 mm

Tonsillectomy Instruments

ROEDER LOOP APPLICATOR
• Stainless Steel

Number Description
N46400

Loop applicator by Roeder

Overall Length
Type E

27 cm

NAGER TONSIL SUTURE NEEDLE
• Stainless Steel

Number Description

Overall Length

N46500

24 cm

Tonsil suture needle by Nager

HURD TONSIL SUTURE NEEDLE
• Stainless Steel

Number Description

Overall Length

N46700

Tonsil Suture Needle by Hurd

Right hand

22.5 cm

N46800

Tonsil Suture Needle by Hurd

Left hand

22.5 cm

SUTURE HOOK
• Stainless Steel

Number Description
N46900

Suture Hook

Overall Length
Right hand

20.5 cm

241

Tonsillectomy Instruments

KNOT TIER
• Stainless Steel

Number Description
N47100

Knot tier

Overall Length
Fork shaped, blunt

20.5 cm

LUNIATSCHEK TONSIL GAUZE PACKERS
• Stainless Steel

Number Description

Overall Length

N43700

19 cm

Tonsil gauze packers by Luniatschek

ABRAHAM TONSIL KNIFE
• Stainless Steel

242

Number Description

Overall Length

N48000

21 cm

Tonsil knife by Abraham

Tonsil Needles

TONSIL SEPTAL CANNULAS WITH LUER-LOCK HUB
• Stainless Steel

Number Description

Diameter

Length

L29510

Tonsil Cannulas with Luer-Lock Hub

Straight

0.8 mm (22 g)

75 / 25 mm

L29514

Tonsil Cannulas with Luer-Lock Hub

Knee bent, 45 °

0.8 mm (22 g)

75 / 25 mm

L29519

Tonsil Cannulas with Luer-Lock Hub

Curved, 90°

0.8 mm (22 g)

75 / 25 mm

243

Tonsil Suction Tips

ANDREW PYNCHON PEDIATRIC SUCTION TUBES
Number Description

Diameter Length

N506-0421 Andrew Pynchon pediatric suction tubes, tip with lateral holes

3 mm

24 cm

N506-0422 Andrew Pynchon pediatric suction tubes, tip with lateral holes

4.2 mm

24 cm

N506-0424 Andrew Pynchon pediatric suction tubes, tip with lateral holes

6 mm

24 cm

YANKAUER PEDIATRIC SUCTION TUBE
Number Description
N506-0303 Yankauer pediatric suction tube

Diameter Length
with tube olive

3.5 mm

WALTON YANKAUER SUCTION TUBE

244

Number Description

Length

N506-0304 Walton Yankauer suction tube regulating valve with tube olive

32 cm

22 cm

Tonsil Suctions Tips

YANKAUER ROUND-TIP SUCTION TUBE
Number Description

Length

N506-0306 Yankauer suction tube with round suction tip, tube olive

23 cm

YANKAUER SUCTION TUBE
Number Description

Central
bore Ø

Length

N506-0300 Yankauer suction tube with tube olive

without light guide

2 mm

28.5 cm

N506-0301 Yankauer suction tube with tube olive

without light guide

4.8 mm

28.5 cm

N506-0308 Yankauer suction tube with tube olive

with light guide

2 mm

28.5 cm

Number

Description

Length

N506-0302

Yankauer suction tube with wall suction extension and tube olive

31 cm

N506-03214

Yankauer suction tube with wall suction extension and tube olive

35.5 cm

N506-03216

Yankauer suction tube with wall suction extension and tube olive

40.5 cm

N506-03218

Yankauer suction tube with wall suction extension and tube olive

45.5 cm

245

Tonsil Accessories

VETTER TONSIL COMPRESSOR
• Stainless Steel

Number Description
N22595

Vetter Tonsil Compressor

LUNIATSCHECK TONSIL GAUZE PACKER
• Stainless Steel

246

Number Description

Working Length

N22595

18 cm

Luniatscheck Tonsil Gauze Packer



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Create Date                     : 2017:10:16 13:58:44-04:00
Creator                         : Adobe InDesign CC 2017 (Windows)
Modify Date                     : 2017:10:16 14:05:19-04:00
Language                        : en-US
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Instance ID                     : uuid:0fd9ea20-adb0-43f5-ad26-0935100da2ae
Original Document ID            : adobe:docid:indd:c486fb8a-7f36-11dd-a9c1-ef627ebe2749
Document ID                     : xmp.id:82400ca0-84b5-6b47-b1d7-520a283abd0c
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:f9d38e8f-5cf1-dd42-85f8-0b21cfb3540a
Derived From Document ID        : xmp.did:ec1eb3a9-d638-c142-826d-eb3aa16871ab
Derived From Original Document ID: adobe:docid:indd:c486fb8a-7f36-11dd-a9c1-ef627ebe2749
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2017 (Windows)
History Changed                 : /
History When                    : 2017:10:16 13:58:44-04:00
Metadata Date                   : 2017:10:16 14:05:19-04:00
Creator Tool                    : Adobe InDesign CC 2017 (Windows)
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 238

EXIF Metadata provided by EXIF.tools