IS DL8408WT 10

2018-05-07

: Is-Dl8408Wt 10 is-dl8408wt_10 images 708 p4dbimg

Open the PDF directly: View PDF PDF.
Page Count: 2

DownloadIS-DL8408WT 10
Open PDF In BrowserView PDF
Assembly Instruction Sheet #IS-DL8408WT
For Style DL8408WT
Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection.
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (2) B10 Candelabra Base Bulbs 60W Maximum or
(2) Candelabra Base T8 Vintage Bulbs are recommended but not supplied.
Estimated Assembly Time: 20-30 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.

Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents
A

Front Glass
D Panel
x1

Inner Backplate
x1

STEP 2 - Install Inner Backplate
A. Pass the supply wires and ground wire through Inner Backplate (A).
Attach the Inner Backplate (A) to the Outlet Box with the head of
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug with screwdrivers.

A

Mounting
B Screw
x2

Outlet Box Screw
(not supplied)

Outlet Box

Supply Wires and
Ground Wire

Fixture
C Body
x1

Side Glass
E Panel
x2
Figure 2

STEP 1 - Install Glass Panels
A. Place the Fixture Body (C) onto a flat
working surface with the bottom of the
cage facing you.
B. Remove lock screws and tabs from the
bottom corners of the Fixture Body (C).
C. Insert the Side Glass Panels (E) into
the side slot in the Fixture Body (C).
Insert the Front Glass Panel (D) into
the front slot in the Fixture Body (C).
Attach tabs back onto bottom corners
of the Fixture Body (C) to hold Glass
Panels (D/E) and secure with
previously removed lock screws. Hand
tighten until snug with screwdrivers.

Slot
STEP 3 - Wire Connections

C

A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.

E

White wire
from outlet box

White wire
from fixture

Black wire from
outlet box (or Red)

Black wire
from fixture

Figure 1
Bare, or Green
Ground wire
from outlet box

D

Ground wire
from Fixture

Green Ground Screw
on the Crossbar

Tab
Tab
BOTTOM VIEW

2017 QuoizelInc.

Corner

Figure 3

Lock Screw

Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
1of2

ReleasedDate:2017-09-14

STEP 4 - Install Fixture Body

DL8408WT

A. Attach the Fixture Body (C) over the Inner Backplate (A) and secure
with Mounting Screws (B). Tighten until snug with screwdrivers.

FINISH: WESTERN BRONZE

Figure 4

6.25”

8”
C

A

12.75”
B
19”

STEP 5 - Install Bulbs
Fixture can
only be
mounted in
the direction
indicated

A. Insert bulb s onto sockets and screw snugly into place.

T8 Vintage Bulb
(recommended
but not Supplied)

9”

5”

Socket

Figure 5
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"

STEP 6 - Apply Silicone Sealer
A. Make sure the exterior wall
surface and fixture backplate
are free of dirt before applying
caulk. Using exterior grade
caulk, caulk over top of
backplate and down both sides.
Do not caulk the bottom of the
fixture backplate to ensure
proper moisture drainage.
Your fixture is now assembled
and ready to use. Enjoy!

Exterior
Grade Caulk

Exterior
Grade
Caulk
Backplate

Figure 6

2017 QuoizelInc.

Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
2of2

ReleasedDate:2017-09-14
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : jasperz
Create Date                     : 2017:09:14 10:16:56+08:00
Modify Date                     : 2017:09:14 10:16:56+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : jasperz
Title                           : IS-DL8408WT.cdr
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:3938b11a-44a3-434b-8959-00ffce31c985
Instance ID                     : uuid:d3f38c48-c4a8-4dda-8f6d-c1553900cd3a
Page Count                      : 2
EXIF Metadata provided by EXIF.tools

Navigation menu