P5423W 01 P5423W_121008WJ 121008WJ

User Manual: P5423W_121008WJ

Open the PDF directly: View PDF .
Page Count: 22

Download
Open PDF In Browser	View PDF

We strive to ensure that our products are of the highest quality
and free of manufacturing defects or missing parts. Howeve r, if
you have any problems with your new product,
DO NOT RETURN IT TO THE STORE,
please contact us toll free @:

1-866-556-2757
FAX: 1-866-873-3531
pooltables@escaladesports.com
Or write to:
Escalade Sports
Customer Service Department
P.O. Box 889
Evansville IN 47706

Please have your model number when inquiring about parts.
Whe n contactin g Escalad e Sport s pleas e provid e you r mode l numbe r, d at e
cod e (i f a pplicable ) an d par t n umbe r i f requestin g a replacemen t part . T hes e
number s ar e locate d o n th e product , packaging , an d t hi s owner s m anual .

P5423W

Your Model Number _____________________
Date Code ________________________
2-P5423W-WJ
Purchase Date ________________________

PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
All Rights Reserved.
© 2012 Escalade Sports

For Customer Service Call 1-866-556-2757

CAUTION
THE SPRAY ADHESIVE USED FOR APPLYING PLAYFIELD CLOTH IS EXTREMELY FLAMMABLE AND UNDER
PRESSURE ! CAREFULLY READ CAUTIONS ON SPRAY ADHESIVE CONTAINER ! KEEP OUT OF THE REACH OF
CHILDREN ! DO NOT USE OR STORE NEAR HEAT SOURCE , FLAMES , SPARKS OR WHEN SMOKING ! WORK
AREA MUST BE WELL VENTILATED . OPEN DOORS AND WINDOWS WHEN USING SPRAY ADHESIVE .

To ensure safety, do not attempt to assemble system without followinginstructions carefully. Proper and complete assembly, use, and supervision is essential for
proper operation and to reduce the risk of accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and
operated properly.

READ AND FOLLOW ALL ASSEMBLY, OPERATION, AND
SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO
ADULTS ARE NEEDED TO PUT THIS TABLE
TOGETHER.

Tools Needed: (Not Included)
• Philips Screwdriver
• Putty Knife
• Needle Nose Plyers

• Tape Measure
• Sanding Block
• Scissors or Sharp Knife

• Adjustable Wrench
• Small Hammer
• Carpenters Level
• Ratchet with socket
• 12mm Socket or End Wrench

NOTE: This table adds weight to any floor. Be sure floor can withstand this kind of weight.
If floor sags, table will be impossible to level.

For Customer Service Call 1-866-556-2757

Pa r t Li s t
(To Scale)

H2 - 3/8” Lock
Washer (16 pcs)

H1 - 3/8” x 2-1/4” Bolt
(8 pcs)

H5 - 3/8” x 3” Bolt
(8 pcs)

H8 - 5/16” x 1-1/4” Bolt
(8 pcs)

H6 - WP/4 x 1”
Phillips Washer
Head Screw
(12 pcs)

H9 - 5/16” x 1-3/4” Bolt
(12 pcs)

H12 - 5/16” x 1-5/8” Bolt
(18 pcs)

H13 - 5/16” x 32mm
Flat Washer (18 pcs)

H16 - 1/4” x 1-1/2” Bolt
(4 pcs)

H17 - 1/4” x 15mm
Flat Washer (4 pcs)

H3 - 3/8” x 25mm
Flat Washer (32 pcs)

H7 - F5 x 1-3/4”
Phillips Flat Head Screw
(16 pcs)

H10 - 5/16” x 23mm
Flat Washer (12 pcs)

H14 - Pocket Nail
(36 pcs)

H4 - 3/8” Hex Nut
(16 pcs)

H11 - T4 x 15mm
Phillips Round Head
Screw (24 pcs)

H15 - 5/16” x 23mm
Flat Washer
(8 pcs)

For Customer Service Call 1-866-556-2757

Cu e Stic k
2 Pcs

Triangl e
1 Pc

Playfield Cloth Brush
1 Pc

Playfield Cloth
1 Pc

Billiar d Bal l
1 Se t

Cue Chalk
2 Pc s

Playfield Grout Kit
1 Pc

Playfield Cloth to Playfield
- Spray Adhesive 1 Pc

Wrench
1 Set

Sand Paper for Dried Grout
1 Pc

P3A

NOTE: For P5
Installation.

P3B

NOTE: For P16
Installation.

Leg
2 Pcs

Main Metal Beam
2 Pcs

P6 - Slatron
P6S - Slate

End Board
2 Pcs

P7 - Slatron
P7S - Slate

End Play Bed
2 Pcs

Middle Play Bed
1 Pc

P11

P10

Side Top Rail
2 Pcs

Middle Slat
2 Pcs

End Slat
2 Pcs

End Top Rail
2 Pcs

Shim
8 Pcs
Can also use playing cards (not included)
or Slate / Slatron Shims

P12

Corner Cap
4 Pcs

Side Apron
2 Pcs

For Customer Service Call 1-866-556-2757

P13

P15

P14

End Apron
1 Pc

P17

End Apron with Ball
Return Opening
1 Pc

P19

Leg Leveler
4 Pcs

P20

Right Corner Pocket
1 Pc

Left Corner Pocket

Right Corner Pocket
NOTE: Attach this pocket on
same end as P14 Apron with
Ball Return Opening

1 Pc

Right Middle Pocket
1 Pc

P24

P23

P22

P21

Ball Return
Support Board
1 Pc

Corner Post
4 Pcs

P18

Ball Return Tray Board
1 Pc

P16

Left Corner Pocket
1 Pc

Left Middle Pocket
1 Pc

NOTE: Attach this pocket on
same end as P14 Apron with
Ball Return Opening

1 Pc

P25

Ball Return Tube
4 Pcs

For Customer Service Call 1-866-556-2757

PARTS REQUIRED:

2 pcs - P1 Leg
4 pcs - P18 Leg Leveler

ST E P 1 :

Thread P18 Leg Levelers into P1 Leg as shown in Figure 1.
.
P18
Note: Remove Parts Box, Leg Levelers,
Plastic Pockets and Spray Glue from
inside both Legs.

P18

Figure 1

For Customer Service Call 1-866-556-2757

8 pcs
16 pcs
32 pcs
16 pcs
8 pcs
8 pcs

ST E P 2 :

PARTS REQUIRED:

H1 Bolt
H2 Lock Washer
H3 Washer
H4 Hex Nut
H5 Bolt
H6 Screw

2 pcs - P2 Main Metal Beam
2 pcs - P3A & P3B End Slat
2 pcs - P4 Middle Slat
2 pcs - P5 End Board
1 pc - P16 Ball Return Support Board
1 set - T4 Wrench

Attach each P2 Main Metal Beam to P1 Leg assembly as shown Figure 2 using H1 Bolts, H3 Washers,
H2 Lock Washers and H4 Hex Nuts. Use the T4 Wrench to assemble the hardware. Do not tighten
hardware at this time. Place P3A and P3B End Slats and P4 Middle Slats across P2 Main Beams and
attach using H5 Bolts, H3 washers, H2 Lock Washers and H4 Hex Nuts as shown in Figure 2.
Attach P5 End Boards to P3A End Slat using pre-drilled pilot holes with H6 Screws as shown in Figure 2.
Attach P16 Ball Return Support Board to P3B End Slat using pre-drilled pilot holes with H6 Screws as
shown in Figure 2.
H5
P3A
IMPORTANT NOTE:
Make sure holes are located on the
H3
top of both P2 Main Metal Beams.

H4
P4

H2
H3

P5
H3
H2
H4

P2
P4

P3B
H4

H2
H3
Note: P5 End Boards must be
flush or slightly lower than top
of P3A End Slats.

H3
H1

Figure 2

H6
P16

STEP 3:

Square up P4 Slats by measuring diagonally as show in Figure 3. Diagonal measurements should be
the same within 1/8". If the frame is not square, adjustment can be made by moving table beams P2 in
opposite directions. Once the frame is square, tighten all hardware.
P2
P4

SAME
DIMENSION

Figure 3

P2
7

For Customer Service Call 1-866-556-2757

STE P 4 :

Us e a carpente r ’ s leve l t o leve l tabl e a s clos e a s possible . It i s easie r t o d o i t no w rather than
after the Play Bed is on the frame. To determine the highest corner of the frame place the
level in following two positions. First check the table from end to end as shown in Figure 4.
Then check the table at an angle as shown in Figure 5.
Can also use playing cards for Slate / Slatron Shimming - not included.

Figure 4

Figure 5
All Rights Reserved.
© 2012 Escalade Sports

For Customer Service Call 1-866-556-2757

UNBOX I N G TH E SL AT E (Slat e t a b l e s o nl y: )

CAUTIO N

AFTE R CR AT E PA R T S AR E REM O VED , B EN D NA I L S O R S TAP L E S O VE R W I T H A
HAM M E R AT O NCE ! U S E CAUT IO N WHE N HAND LI N G CR AT E PA R TS !

Figure 6

I t i s n o w t im e t o u ncr a t e t h e s l a t e pi e c e s .
W i t h a c la w hamme r o r c ro w ba r, p r y o f f c ra t e
to p a t t h e notche d corne r. ( Se e FIGUR E 6 )
B E CAREFU L NO T T O DAMAG E SL AT E
INSIDE ! SL AT E I S BRITTL E AN D CA N
B E EASI LY DAMAGE D I F HI T O R PRIE D
AGAINST !

Remov e t h e fron t rai l o f th e crate . S lid e th e slat e
ou t th e f ron t o f th e crate . (FIGUR E 7 )

Figure 7

UNBOXIN G TH E SL ATRO N (Slatro n t able s only: )
I t i s no w t im e t o unbo x th e slatro n pieces .
B E CAREFU L NO T T O DAMAG E SL ATRO N
INSIDE ! SL ATRO N CA N B E EASI LY DAMA GE D I F HI T O R PRIE D A GAINST !
(Se e FIGUR E 8 )

Figure 8

I f th e edge s o f you r Slatro n h a s “fuzz ” o n it ,
lightl y san d t o r emov e wit h sandpape r
provide d i n t h e playbe d kit .

IMPOR TANT !
Th e s heet s o f s latro n ma y no t b e completel y fla t whe n
remove d f ro m t h e shippin g carton . Thi s i s normal . Onc e
the y hav e bee n place d o n th e t abl e fram e an d securel y
fastene d down , the y wil l becom e straigh t an d f lat .
All Rights Reserved.
© 2012 Escalade Sports

For Customer Service Call 1-866-556-2757

PARTS REQUIRED:

THE FOLLOWING STEP REQUIRES
THE HELP OF ANOTHER ADULT!

16 pcs - H7 Screw
2 pcs - P6 End Play Bed
1 pcs - P7 Middle Play Bed

STEP 5:

You can tell the top side of the playfield sections by the beveled edge of the pocket openings
and the countersunk mounting holes. The beveled edges and the countersunk holes must
face up. (See Detail A)
A) Place center section P7 on the two long slats P4.If edges do not align exactly,center playfield as
much as you can. The playfield sections are 51 inches wide. The P4 Middle Slats are 51 inches
long, The play bed sections should be flush with the P4 Middle Slats on both sides of
table.
WARNING: This step requires two adults!
REMEMBER: Be sure countersunk holes in the playfield face up!
B) Secure center section P7 to long slats P4 with screws H7 into countersunk holes.
Note:It is important that the edges of the three pieces of playfield are flush and square.
DO NOT OVER TIGHTEN SCREWS!
Place end Play Bed section P6 onto slats.Be sure they are square,in line and butted up
tight against center section P7.Secure end section P6 to beams using screws H7 into
countersunk holes. DO NOT OVER TIGHTEN SCREWS. NOTE:If necessary,shim underneath
Play Bed where they join together to obtain a smooth,even surface.Shims are provided in the slate
bed kit.
TOP OF PLAY BED MUST BE PRECISELY LEVEL! EDGES MUST BE EVEN WITH ONE
ANOTHER!
H7
P6
H7

H7
Be sure that the side
of the table top
sections with the
countersink around
each hole face up

Detail A

Figure 9
P4
Note: See next page for
Playfield Shimming Instructions.
All Rights Reserved.
© 2012 Escalade Sports

Playbed sections must be flush with
P4 Middle Slats on both side of table.
10

For Customer Service Call 1-866-556-2757

SHIMMING INSTRUCTIONS
( use deck of cards for shimming, not included )
General Rules

Accomplish the leveling of the playing surface with
as few shims as possible.
Do not tap with a hammer or tighten screws
unreasonably tight. You will not be able to compress
the playing surface. You must shim up the playing
surface to level. Shims are meant only to raise the
low places at the seams and ends. Very short and
low places should be grouted. Do not assume the
floor is level. Most leveling can be accomplished by
working with the frame.
If using power tools be sure to use only enough
torque to reasonably tighten screws.
Seams can best be checked by passing your finger
over the seam and feeling if it is flush.
All screws must be tightened after shimming.
No two sets of Play Bed are exactly alike. Some
sets require more or less shimming than others.

Top of playing surface
must be flush at seams!

Shim

STEP BY STEP SHIMMING

( use deck of cards for shimming, not included )

A) Be sure table is set in its final location.
B) Table must be as level as possible before shimming. Large differences in levelness must
be corrected by raising or lowering frame with included leg levelers or shim stock.
DO NOT ASSUME FLOOR IS LEVEL!
C) Tighten down all the playing surface mounting screws.
D) Check with a carpenter’s level to determine where playfield is low on ends, and use finger
tips to locate uneven spots at the seams. Loosen screws at these points and see if
playfield comes up to flush. If so, detach individual shims from the sheet shipped with this
table and place under these areas. Place shims next to screws.
E) Lay a straight edge across seams to be sure playfield pieces are at the same height.
F) After top surface of playfield is flat and level, all screws must be snugged down in tight
position. DO NOT OVER-TIGHTEN SCREWS! Check these screws before proceeding to
the next step.

GROUTING INSTRUCTIONS FOR PLAY BED
- Clean top of playfield with a damp cloth. DO NOT USE TOO MUCH WATER! Allow enough time for
top sections to dry thoroughly before starting the next step.

- A small container of grout has been provided for filling countersinks and small imperfections in the

table seams. Empty 1/3 of grout into a mixing container. Add 1 teaspoon of water and stir-add very
small quantities of grout or water to achieve a thick paste. When mixed, grout should be a thick
paste that will not drip off putty knife. If you do get grout too thin, slowly add more powder.

- Using a putty knife, fill both seams and the four countersunk holes in the center playfield area.

(Only the four countersunk holes in the center of the table need to be filled since the other holes
will be covered by the rails.) Do not use more grout than you need.

- Let grout dry. Read the rest of this manual while you wait!
- Using a medium grit sandpaper and sanding block, sand the filled areas smooth and flat.

RECHECK THESE AREAS TO MAKE SURE THEY ARE FLAT. Re-grout if you still find low places
at countersunk holes or seams.

For Customer Service Call 1-866-556-2757

WARNING

!
First Glue
Application

DO NOT SMOKE WHILE WORKING
WITH CONTACT CEMENT! READ LABEL
ON CEMENT CONTAINER CAREFULLY!

Applying the cloth:

1. Make sure Play Bed is dry and free of dust.
NOTE: Before spraying adhesive, cut a portion of the shipping
carton to use as a shield to prevent cement over spray.
2. Place cloth over Play Bed with equal overhang on all sides.

Figure 10

Spray glue on
edge of slate too.

Second Glue
Application

NOTE: Cloth may seem small but it will stretch a great deal.
3. Fold cloth away from end to expose Play Bed for your first
glue application. Apply contact cement to top surface in a band
4 inches wide on this end. (See FIGURE 10) Coat edge also.
Spray cement smoothly and evenly. Allow cement to become
tacky, wait at least one minute.

Figure 11

4. Fold cloth back over the table. With firm even pressure, press
cloth onto the area that has been coated with cement. Smooth
cloth down and over edges.

Third Glue
Application

FIRST
STRETCH

5. Fold cloth away from side to expose Play Bed for your second glue application. (See FIGURE 11 ). Apply cement to the
side in the same manner as your first glue application. Allow
cement to become tacky, wait at least one minute.
6. Fold cloth back over table. With firm even pressure, press
cloth onto the area that has been coated with cement. Smooth
cloth down and over edges.
7. Fold cloth away from other side to expose Play Bed for your
third glue application. (See FIGURE 12 ). Apply cement to this
side in the same manner. Allow cement to become tacky, wait
at least one minute.

Figure 12
FINAL
STRETCH

Fourth Glue
Application

8. Stretch the cloth across the width and over the edge of the table.
STRETCH HARD ENOUGH TO TAKE OUT WRINKLES, BUT
NOT SO HARD THAT THE CLOTH SLIPS.
9. Fold cloth away from other end to expose Play Bed for your
fourth glue application. (See FIGURE 13 ) Apply cement to this
end in the same manner. Allow cement to become tacky, wait at
least one minute.
10. Make a final stretch along the length of and over the edge of
the table, stretch hard enough to work out all wrinkles. (See
FIGURE 14 ) If cloth is not smooth, lift and re-apply.
NOTE: Rubbing fingers lightly across cloth should not make
cloth move.
11. Locate center of pocket opening. (See Detail A and B ) Using
sharp scissors, make a straight cut. Next, cut to pocket edge
to form pie shapes. (See detail B ) Divide these pie shapes in
half. As you do, the pie shapes begin to relax to allow for
placement. You may need to make additional cuts.
12. Spray adhesive on the underneath side of the play-bed around
pocket face to adhere the cloth. Make sure not to get over spray
of glue on table. Allow cement to become tacky, wait at least
one minute. Stretch the pie shapes down and under the pocket
opening. Press the cloth against the cement on the underside
of the Play Bed. Be sure entire pie shape is fully attached
to underneath side of table.
All Rights Reserved.
© 2012 Escalade Sports

Figure 13
Cut with scissors.
Cloth should cover
pocket edges.

Figure 14

DIVIDE
IN HALF

DO NOT
CUT ANY
CLOSER
THAN 3/4”

CENTER
CUT

DIVIDE
IN HALF

CUT TO
POCKET
EDGES

Detail A

Detail B

CUT TO
POCKET
EDGES

For Customer Service Call 1-866-556-2757

PARTS REQUIRED:

8 pcs - H8 Bolt
8 pcs - H15 Flat Washer
2 pcs - P9 Side Top Rail

2 pcs - P10 End Top Rail
4 pcs - P11 Corner Cap

STEP 6:

On a clean level surface, lay each P9 Side Top Rail and P10 End Top Rail face down as shown in Figure 15.
Next, lay each P11 Corner Cap face down and attach using H8 Bolts with H15 Flat Washers as shown in
Figure 15 and Detail A. Do not tighten H8 Bolts at this time.
Next, Measure from the outer edge of cushion rubber, on each side of P10 End Top Rail to other end of P10
End Top Rail . These two measurements must be the same in order for this rail assembly to be a perfect
rectangle and should measure approx 87 5/8". This measurement may vary slightly from 87 5/8", but both
measurements must be the same. Hold each P10 End Top Rail down with your hand and tighten H8 Bolts - in
the end top rail only. Check to see that both measurements are still the same.
Next, Measure from the outer edge of cushion rubber, on each end of P9 Side Top Rail to other end of P9 Side
Top Rail. These two measurements must be the same in order for this rail assembly to be a perfect rectangle
and should measure approx 43 1/2". This measurement may vary slightly from 43 1/2", but both measurements
must be the same. Hold each P9 Side Top Rail down with your hand and tighten H8 Bolts - in side top rail only.
Check to see that both measurements are still the same.
Lastly, Check all (4) measurements to insure this assembly is a perfect rectangle and double check that all
corner cap bolts are tight.

P10
Ap

pro

7
x8

”
5/8

2”

/8”

NOTE:
All parts are
upside down

8
rox

Ap Ap
pr pr
ox ox
43 43
1/ 1/2
2” ”

P9
H15

P10

H8
H15

P10
P9
Figure 15
P11

For Customer Service Call 1-866-556-2757

PARTS REQUIRED:

12 pcs - H11 Screw
1 pc - P13 End Apron

1 pc - P14 End Apron with Ball Return Opening
4 pcs - P15 Corner Post

STEP 7:

Slide and attach each P15 Corner Post onto the end of each P13 and P14 End Apron using H11 Screws as
shown in Figure 16A. Tighten, but do not strip out H11 Screws.
IMPORTANT NOTE: Study and assemble parts exactly as per Figure 16A.

NOTE: BE SURE EACH
CORNER POST IS FLUSH
WITH END APRON.

P15

INCORRECT

CORRECT

NOTE: SILVER EDGE TRIM
AT UPWARD POSITION.

H11
P14

Figure 16A
NOTE: BE SURE CORNER
CAP IS COMPLETELY
PUSHED ONTO END APRON.

H11

NOTE: SILVER EDGE TRIM
AT UPWARD POSITION.

H11
P13
H11

For Customer Service Call 1-866-556-2757

PARTS REQUIRED:

12 pcs - H9 Bolt
12 pcs - H10 Washer

12 pcs - H11 Screw
2 pcs - P12 Side Apron

STEP 8:

With the rail assembly face down, attach P12 Side Aprons using H9 Bolts with H10 Washers (see inset). Do not
tighten yet.
Next, attach previous assemblies P13 and P14 End Aprons flush against the bottom of the P10 End Top Rail and
align using threaded inserts on the underside of each rail. Attach P13 and P14 End Apron assembly using H9
Bolts with H10 Washers (see inset). Do not tighten yet.
Be sure each P15 Corner Post is flush with each P12 Side Apron, then attach using H11 Screws.
Tighten, but do not strip out H11 Screws.
Lastly, tighten all H9 Apron Bolts.

H9
H10
H11

P15

P13

P12

H10

P10

P12
P14

Figure 16B
P15

For Customer Service Call 1-866-556-2757

PARTS REQUIRED:

18 pcs - H12 Bolt
18 pcs - H13 Washer

STEP 9:

With the help of four adults, carefully rotate the rail and apron assembly and then place over the play
bed as shown. From the underside of the table, insert H12 Bolts with H13 Washers up through the
play bed and into the threaded inserts of each rail. Be sure the rail assembly is aligned with the play
bed and pockets, then tighten all bolts.

Important Note : Once Rail and Apron assembly is placed onto the playfield - carefully sight down
onto each pocket opening and adjust rail and apron assembly equal to all six pocket openings
before tightening H12 bolts.

Figure 17

P14

H13
H12
H13
H12

IMPORTANT NOTE: Make sure this P14 End Apron with Ball
Return Opening is on same end as P16 Ball Return Support
Board assembled in STEP 2.

For Customer Service Call 1-866-556-2757

PARTS REQUIRED:

1 pc - P19 Right Corner Pocket
1 pc - P20 Right Middle Pocket
1 pc - P21 Right Corner Pocket

1 pc - P22 Left Corner Pocket
1 pc - P23 Left Middle Pocket
1 pc - P24 Left Corner Pocket
4 pcs - P25 Ball Return Tube

STEP 10:

Connect P22 Left Corner Pocket, P23 Left Middle Pocket and P24 Left Corner Pocket with P25
Ball Return Tubes as shown in Figure 18.

P25

P24

e
Tub

P25
e
Tub

s
goe

ide

ins

P22

sid

out

Figure 18

P23

Connect P19 Right Corner Pocket, P20 Right Middle Pocket and P21 Right Corner Pocket with
P25 Ball Return Tubes as shown in Figure 19.

P25

BALL RETURN
OPENING - END
OF TABLE

Tub

sid

s in

oe
eg

P19

P25
P21
e
Tub

s
goe

sid

out

Figure 19
P20

For Customer Service Call 1-866-556-2757

THIS STEP REQUIRES THREE OR MORE ADULTS.
VERY CAREFULLY INSERT RIGHT POCKET RETURN AND
LEFT POCKET RETURN INTO THE DROP POCKET OPENINGS
FROM UNDERSIDE OF THE TABLE.

PARTS REQUIRED:

36 pcs - H14 Pocket Nail

STEP 11:

Insert Right Pocket Return and Left Pocket Return from previous assembly STEP 10 into the drop
pocket openings from underside of the table. Fasten pockets using six H14 Nails per pocket. Hold the
nails with needle nose pliers and tap them in with a small hammer. Once the nails have started into
plastic, hammer them completely into the rails until heads are flush with plastic as shown Figure 20.
Important Note: All H14 pocket nails must be tapped completely into place - otherwise - damage to the
billiard balls may occur.

Figure 20

H14

For Customer Service Call 1-866-556-2757

PARTS REQUIRED:
4 pcs - H6 Screw
4 pcs - H16 Bolt
4 pcs - H17 Washer

1 pc - P17 Ball Return Tray Board
2 pcs - A1 Cue Stick
1 pc - A2 Triangle

1 pc - A3 Brush
1 set - A5 Billiard Ball
2 pcs - A6 Chalk

STEP 12:

Attach P17 Ball Return Tray Board onto P16 Ball Return Support Board using H16 Bolts and H17 Washers
as shown in Figure 21.
Attach P17 Ball Return Tray Board onto P14 End Apron with Opening Ball Return Trim using H6 Screws
as shown in Figure 21. Tighten, but do not strip out H6 Screws.

Figure 21

A5
A1

A6
A3

P14

Note: Small wooden block on this upper side.

H17

P17
Note: Small wooden block
on this upper side.

H16
H6

For Customer Service Call 1-866-556-2757

Congratulations! You have now assembled your pool table. Please note the Care
and Use instructions below to insure many years of trouble free use of your pool
table.

CARE AND USE OF YOUR POOL TABLE
1.
2.
3.
4.
5.
6.
7.
8.

Use spray furniture polish to clean all exterior surfaces of your pool table.
Use the table brush provided to clean the cloth on the table.
Use a carpenters level to properly level table using the leg levelers.
This product is intended for INDOOR use only.
DO NOT sit, climb or lean on the table.
DO NOT drag the table when moving it. This will damage the legs.
DO NOT set drinks on the table.
The purchase of a billiard table cover will help protect and keep your table
clean while not is use.

For Customer Service Call 1-866-556-2757

PARTS LIST FOR MODEL # P5423W
PART #
P5423WWJH1
P5423WWJH2
P5423WWJH3
P5423WWJH4
P5423WWJH5
P5423WWJH6
P5423WWJH7
P5423WWJH8
P5423WWJH9
P5423WWJH10
P5423WWJH11
P5423WWJH12
P5423WWJH13
P5423WWJH14
P5423WWJH15
P5423WWJH16
P5423WWJH17
P5423WWJT1
P5423WWJT2
P5423WWJT3
P5423WWJT4
P5423WWJA1
P5423WWJA2
P5423WWJA3
P5423WWJA4
P5423WWJA5
P5423WWJA6
P5423WWJP1
P5423WWJP2
P5423WWJP3A
P5423WWJP3B
P5423WWJP4
P5423WWJP5
P5423WWJP6
P5423WWJP6S
P5423WWJP7
P5423WWJP7S
P5423WWJP8
P5423WWJP9
P5423WWJP10
P5423WWJP11
P5423WWJP12
P5423WWJP13
P5423WWJP14
P5423WWJP15
P5423WWJP16
P5423WWJP17
P5423WWJP18
P5423WWJP19
P5423WWJP20
P5423WWJP21
P5423WWJP22
P5423WWJP23
P5423WWJP24
P5423WWJP25
P5423WWJK1
P5423WWJM1
All Rights Reserved.
© 2012 Escalade Sports

KEY #
H1
H2
H3
H4
H5
H6
H7
H8
H9
H10
H11
H12
H13
H14
H15
H16
H17
T1
T2
T3
T4
A1
A2
A3
A4
A5
A6
P1
P2
P3A
P3B
P4
P5
P6
P6S
P7
P7S
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P25
K1
M1

DESCRIPTION

QTY.

3/8” x 2-1/4” Bolt
3/8” Lock Washer
3/8” x 25mm Flat Washer
3/8” Hex Nut
3/8” x 3” Bolt
WP/4 x 1” Phillips Washer Head Screw
F5 x 1-3/4” Phillips Flat Head Screw
5/16” x 1-1/4” Bolt
5/16” x 1-3/4” Bolt
5/16” x 23mm Flat Washer
T4 x 15mm Phillips Round Head Screw
5/16” x 1-5/8” Bolt
5/16” x 32mm Flat Washer
Pocket Nail
5/16“ x 23mm Flat Washer
1/4” x 1-1/2” Bolt
1/4” x 15mm Flat Washer
Playfield Grout Kit
Playfield Cloth to Playfield - Spray Adhesive
Sand Paper for Dried Grout
Wrench (set)
Cue Stick
Triangle
Playfield Cloth Brush
Playfield Cloth
Billiard Ball
Cue Chalk
Leg
Main Metal Beam
End Slat (Note: For P5 Installation)
End Slat (Note: For P16 Installation)
Middle Slat
End Board
End Play Bed Slatron (P2000W)
End Play Bed Slate (809-551)
Middle Play Bed Slatron (P2000W)
Middle Play Bed Slate (809-551)
Shim
Side Top Rail
End Top Rail
Corner Cap
Side Apron
End Apron
End Apron with Ball Return Opening
Corner Post
Ball Return Support Board
Ball Return Tray Board
Leg Leveler
Right Corner Pocket
Right Middle Pocket
Right Corner Pocket
Left Corner Pocket
Left Middle Poket
Left Corner Pocket
Ball Return Tube
Hardware Kit
Owner’s Manual

8
16
32
16
8
12
16
8
12
12
24
18
18
36
8
4
4
1
1
1
1
2
1
1
1
1
2
2
2
1
1
2
2
2
2
1
1
8
2
2
4
2
1
1
4
1
1
4
1
1
1
1
1
1
4
1
1

For Customer Service Call 1-866-556-2757

90 DAY LIMITED WARRANTY
This customer warranty extends to the original owner, on the purchase of any ESCALADE SPORTS
Product (hereinafter referred as the "Product").
WARRANTY DURATION: This Product is warranted to the original owner, for a period of 90 days from the
original purchase.
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original owner, this product to be free
from defects in material and workmanship when used for the intended purpose under normal use and
conditions. THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN DAMAGED BY ACCIDENT,
UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW INSTRUCTIONS
PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL
AND WORKMANSHIP.
WARRANTY REPLACEMENT: During the above 90 day warranty period, ESCALADE SPORTS shall
provide replacement components or replace with a comparable product at our choosing. If product is
defective under normal use and proper care, please contact our Customer Service Dept.

1-866-556-2757 / Customer Service Dept.
Or Write us at:
Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706
Attn: Customer Service Dept.
Or E-mail us at:
customerservice@escaladesports.com
Other than shipping requirements no charge will be made for such replacement of in-warranty Products.

WARRANTY ON SLATE/SLATRON™ SURFACE
Manufacturer warrants for five (5) years from the date of purchase for the Slatron™ and ten (10) years for
slate, Escalade Sports will repair the playing surface of this table, free of charge, if it fails to remain flat,
within a tolerance of + or – 30/1000 of an inch, measuring from any flat plane within the playing
surface. NOTE: Cloth not included in warranty. Should this product become defective due to material or
workmanship within period, contact the Customer Service Department. This warranty is not transferable
and does not cover normal wear and tear, or damage caused by improper handling, installation or use of
this product. This warranty is also void if product is in any way abused, damaged, or modified from its
original state, or if used for other than indoor residential use. This warranty gives the consumer specific
legal rights, and may have other rights which may vary from state to state.

WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE
ABOVE 90 DAY PERIOD. ESCALADE SPORTS SHALL NOT BE LIABLE FOR LOSS OF
USE OF THE PRODUCT OR OTHER CONSEQUENTIAL OR INCIDENTAL COSTS,
EXPENSES OR DAMAGES INCURRED BY THE CONSUMER OF ANY OTHER USE.
Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental
damages, so the above limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other rights which
may vary from state to state.
All Rights Reserved.
© 2012 Escalade Sports

For Customer Service Call 1-866-556-2757

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.1-c036 46.277092, Fri Feb 23 2007 14:17:08
Modify Date                     : 2012:10:09 09:34:21+08:00
Create Date                     : 2012:08:29 11:42:28+08:00
Metadata Date                   : 2012:10:09 09:34:21+08:00
Creator Tool                    : Adobe Illustrator CS3
Thumbnail Width                 : 184
Thumbnail Height                : 256
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 9982 bytes, use -b option to extract)
Format                          : application/pdf
Title                           : P5423W - 01
Creator                         : jaguilar
Document ID                     : uuid:1ef88a16-bb05-4857-afce-799c767640d7
Instance ID                     : uuid:c7dbcbbc-7589-42fa-982d-b4152334d18b
Producer                        : Adobe PDF library 8.00
N Pages                         : 1
Has Visible Transparency        : False
Has Visible Overprint           : False
Max Page Size W                 : 8.263889
Max Page Size H                 : 11.694444
Max Page Size Unit              : Inches
Font Name                       : ArialMT
Font Family                     : Arial
Font Face                       : Regular
Font Type                       : Open Type
Font Version                    : Version 5.10
Font Composite                  : False
Font File Name                  : arial.ttf
Plate Names                     : Black
Swatch Group Name               : Default Swatch Group
Swatch Group Type               : 0
Page Count                      : 22
Author                          : jaguilar

EXIF Metadata provided by EXIF.tools

P5423W 01 P5423W_121008WJ 121008WJ

Navigation menu

Versions of this User Manual:

Views

Navigation