SMA1301_GUI_User_Manual_Rev0.0.2x SMA1301 GUI User Manual Rev0.0.2
User Manual:
Open the PDF directly: View PDF 
.
Page Count: 19
| Download | |
| Open PDF In Browser | View PDF |
GUI User Manual Revision 0.0.2 *Technology by © 2017 Silicon Mitus, Inc. December 2017 –Rev0.0.2 www.siliconmitus.com 1 / 19 GUI User Manual 1. Purpose Graphic User Interface (GUI) is a software program that verifies and tests the function of the Silicon Mitus product. This document is based on SMA1301 GUI. USB to I2C board Connection SMA1301.exe Run Control register data & Read/Write with device Figure 1. Active Flow The Silicon Mitus evaluation system has an I2C port, so the user can control the action via the GUI program. The diagram below describes the connection for the Silicon Mitus evaluation system using the GUI Program with test equipment, USB to I2C Board, PC, USB cable and Silicon Mitus Evaluation Board (EVB) Kit. Figure 2. Connection Diagram www.siliconmitus.com 2 / 19 © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 GUI User Manual 2. Installation Unzip SMA1301_Control_Panel.zip to a local PC. To install the program, run “Setup.exe” file. © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 www.siliconmitus.com 3 / 19 GUI User Manual Installation Path 1. Windows Start → Click “ “ SMA1301 2. C:\Program Files (x86)\Iron Device Corporation\SMA1301 folder. Run with SMA1301.exe 3. Device Configuration Connect ‘USB to I2C Board’ to the ‘Evaluation Board Kit.’ 1. Run SMA1301 GUI Program 2. If the USB to I2C Board is not connected normally, an error message pop-up window will appear. Figure 3. Error Message Pop-up www.siliconmitus.com 4 / 19 © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 GUI User Manual 4. Board Manual 4.1 Introduction The SMA1301 Evaluation (EV) Board is a demonstration and evaluation board that shows the capabilities and features of the SMA1301 chipset designed by Silicon Mitus (Iron Device). This board has an I2S interface for digital input and differential analog output with a 2.54 mm pitch header. This board can operate the Class-D amplifier with an integrated boost converter. The boost converter converts output voltage into the digital amplifier to produce stable large sound pressure levels. It has a typical output voltage of 5.5 V to 6.1 V and class-G control by digital feed-forward processing. 4.2 Board Package Content The SMA1301 EV Board package includes the following: 1. 2. 3. 4. SMA1301 EV Board USB to I2C Control Board Cable set to connect the board in lab conditions Control S/W (Released by e-mail. Please contact Silicon Mitus separately.) 4.3 EV Board Overview Figure 4. SMA1301 EV Board Placement (left: WLCSP / right: QFN) Figure 5. SMA1301 EV Board (left: WLCSP / right: QFN) © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 www.siliconmitus.com 5 / 19 GUI User Manual Figure 6. USB to High Speed I2C Control Board Type: 2.54 mm Pitch Pin Header for J6 Pin Description Value 1 3.3 V LDO Output +3.3 V 2 IOVDD IOVDD Do not connect Pin 1 and Pin 2 for SMA1301 (IO voltage should be +1.8 V) Type: 2.54 mm Pitch Pin Deader for J7 Pin Description Value 1 IOVDD IOVDD (+1.8 V from EV board) 2 GND GND 3 SCL 0 V to +1.8 V 4 SDA 0 V to +1.8 V Figure 7. SMA1301 Ordering Information www.siliconmitus.com 6 / 19 © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 GUI User Manual 4.4 Board Schematic Figure 8. SMA1301 EV Board Schematic (WLCSP) © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 www.siliconmitus.com 7 / 19 GUI User Manual Figure 9. SMA1301 EV Board Schematic (QFN) www.siliconmitus.com 8 / 19 © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 GUI User Manual 4.5 Connectors J1: DVDD / 1.8 V Type: 2.54 mm Pitch Pin Header Pin Description Value 1 1.8 V +1.8 V (LDO on board) 2 DVDD +1.8 V (external power supply) Pin 1 and Pin 2 should be connected when using LDO on board for DVDD. J2: VBAT Type: 2.54 mm Pitch Pin Header Pin Description Value 1 VBAT (battery voltage) Typical +3.6 V / Maximum +4.2 V 2 GND GND Pin Description Value 1 DVDD DVDD (+1.8 V) 2 GND GND 3 SCL 0V to +1.8 V 4 SDA 0V to +1.8 V Pin Description Value 1, 3, 5, 7 GND GND 2 LRCK 0V to +1.8 V 4 SCK 0V to +1.8 V 6 SDI (input data from source) 0V to +1.8 V 8 SDO (output data from chipset) 0V to +1.8 V J3: I2C Control Pin Type: 2.54 mm Pitch Pin Header J5 (WLCSP) / J4 (QFN): I2S Input Port Type: 2.54 mm Pitch Pin Header J6 (WLCSP) / J7 (QFN): Output Type: 2.54 mm Pitch Pin Header Pin Description Value 1 SPK Output P Max +6.1 V 2 SPK Output N Max +6.1 V J4 (WLCSP) / J5 (QFN) : External Clock Input Type: 2.54 mm Pitch Pin Header Pin Description Value 1 GND GND 2 MCLKO External Clock © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 www.siliconmitus.com 9 / 19 GUI User Manual 4.6 Measurement Set Up (APX525) This set up is for the evaluation of SMA1301. Reference equipment is APX-525 from Audio Precision. 4.6.1 Connection Figure 10. Measurement Connection (I2S input) www.siliconmitus.com 10 / 19 © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 GUI User Manual 5. Detail Controls 5.1 Control Panel Overview (Main Panel) Figure 11. SMA1301 Mobile Audio Hub IC Register Control Panel No. Item ① Power On/Off with Sequence ② I2C ADDR ③ Volume Control Description Power On: Power-up Speaker Output On De-mute Power Off: Mute Speaker Output Off Power Off High: I2C Slave Address with 0x3E Low: I2C Slave Address with 0x1E Master Volume Control ④ Write to Device Read Set Value from Panels and Write to DUT ⑤ Read from Device ⑥ DSP On/Off ⑦ Status Monitoring ⑧ Menu Bar – File ⑨ Menu Bar – Tool R Read I2C from DUT and Set Panel EQ: On/Off BassBoost: On/Off DRC: On/Off Open Status Monitoring Panel Reads status register and updates display every 0.2 seconds Stops monitoring when clicked again Load Register: Register Load from .dat file Save Register: Register Save to .dat file and datx file Direct Register Control Panel – Open Direct Register Control Panel © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 www.siliconmitus.com 11 / 19 GUI User Manual 5.2 Digital I/O Figure 12. Digital IO Control Panel No. Item Description ① Input1 CTRL 1 I2S Input Format Settings ② ③ Input1 CTRL 2 Input1 CTRL 3,4 PCM Input Format Settings PCM Slot Settings ④ SRC Bypass ⑤ Port Config. ⑥ Port Output Format ⑦ Port Select ⑧ Input Gain Sample Rate Converter turns off when checked Port Configuration Use only “OUT: Port3, IN: Port 1-DAC” SDO Signal Format Select signal to output only when in master mode (see TOP Manager Panel) Format Convert Input Mixer Output (48 KHz) SPK Path after DSP (48 KHz) Digital Input Gain www.siliconmitus.com 12 / 19 © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 GUI User Manual 5.3 EQ Figure 13. EQ Control Panel Figure 14. Parametric EQ Panel No. ① Item EQ ② EQ Filters ③ Parametric EQ ④ EQ Band © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 Description EQ is bypassed if checked User Defined User can change/tune filter Pre-defined Classic / Rock & Pop / Jazz / R&B / Dance / Speech Graphical display that user can tune Q Factor Biquad Filter Type PEQ Butter Worth HPF Butter Worth LPF Gain (-20 dB to +20 dB) Frequency 20 Hz to 20 KHz Check Box Checked: On www.siliconmitus.com 13 / 19 GUI User Manual 5.4 BassBoost Figure 15. BassBoost Control Panel No. ① Item HPF Frequency Description 1st Order High Pass Filter Frequency Setting. “0” is off ② Boost Frequency Boost Frequency Setting: 20 Hz to 1 KHz ③ B.Boost input Select input of Bass Boost Block (Pre or Post HPF) ④ Filter Type Band Pass Filter or Low Pass Filter Type ⑤ B.Boost Gain Bass Boost Gain Setting ⑥ B.BoostTHRES (Boost Trigger) Set the starting limit of Bass Boost ⑦ Attack Release Time (Boost Trigger) Low Pass Frequency (Boost Trigger) Set the attack/release time limit of Bass Boost Low pass filter of the signal that controls the attack release function Should be set above boost frequency ⑧ 5.5 Volume Figure 16. Volume Control Panel No. Item Description ① Volume Control ② Vol./Mute Control Master Volume for RCV/Mono SPK/Left SPK for Stereo Volume and Mute Slope Control Fade In / Fade Out Effect www.siliconmitus.com 14 / 19 © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 GUI User Manual 5.6 Boost & Class D Figure 17. Output & BST Control Panel No. Item ① SPK mode ② BST Control ③ Class D Amp Control ④ Class G Control ⑤ BST Trimming © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 Description Off (default) SPK On (mono for one chip) SPK On (stereo for two chips) Boost On/Off On: Set to attack level with b’0000 Off: Set to attach level with b’1111 Boost Voltage: +5.5 V to +6.1 V Fast Charge Enable / Disable FLT_VDD_GAIN b’0000: 2.40 V to b’1111: 3.115 V SPK Hysteresis Feedback PWM Frequency of Speaker Output SPK_BDELAY / PWM Slope Control / PWM Dead Time Control Do not control this value. This value should be provided by and used accordingly to Silicon Mitus Release Time Attack Level On: b’0000 Off: b’1111 Do not edit. Please use recommended values. www.siliconmitus.com 15 / 19 GUI User Manual 5.7 System Setting Figure 18. System Setting No. Item ① System CLK ② Power Up ③ L/R SPK Terminal Swap ④ L/R Data Swap ⑤ Mono Mix Description Ext. CLK 19.2 MHz Ext. CLK 24.576 MHz Analog Block Power On Normal LR SPK Out Terminal Swapped Data Swap for Left and Right Channels Disable Mono Mixing www.siliconmitus.com 16 / 19 © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 GUI User Manual 5.8 TOP Manager Figure 19. Top Level Management Control Panel No. ① Item PLL_PD ② Clock Sel ③ PLL_LOCK_SKIP ④ DAC Down Conversion ⑤ PLL_REF_CLK1 ⑥ SDO PAD OOT ⑦ PLL_REF_CLK2 ⑧ Top Manage2 ⑨ Top Manage3 © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 Description PLL On/Off System Clock Selection External CLK PLL CLK PLL_LOCK_SKIP: Enable / Disable Down Conversion or Normal PLL Input Source Internal OSC External CLK High-Z@LRCK L or High-Z@LRCL H SCK from External PLLREF_CLK1 There are 2ch(port)s at DAC input internally ADC: ADC output connect to CH2 Input Port “L”: DAC Only Mode (ADC output is not connected) Output Format for I2S LJ / RJ / I2S / SPI / PCM Short / PCM Long SCK_RATE 64 fs or 32 fs SDO_LENGTH 24-bit / 20-bit / 16-bit LRCK_POL H Valid or L Valid www.siliconmitus.com 17 / 19 GUI User Manual 5.9 Protection Control Figure 20. Protection Control Panel No. Item ① Thermal Protection Option ② OCP Mode Description Disable Ignore Threshold1 (TSDW), Shutdown at Threshold2 (TSD) Reduced 6 dB Output at Threshold1 (TSDW), Shutdown at Threshold2 (TSD) Shutdown at Threshold1 (TSDW) and Threshold2 (TSD) Permanent Shutdown of Output Auto Recover (1 sec) Other controls are not used 5.10 Status Monitoring Figure 21. Status Monitoring Panel No. Item Description ① OCP SPK or OCP BST ② TSDW ③ TSD CLOCK MON Over Current Protection at Output SPK or BST Thermal Shutdown Warning Protection (Threshold1) Output level is reduced by -6 dB (default option) Thermal Shutdown Protection (Threshold2) Clock Fault Monitoring ④ www.siliconmitus.com 18 / 19 © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 GUI User Manual Revision History Rev 0.0.0 0.0.1 0.0.2 DATE 09/05/2017 09/11/2017 10/20/2017 CHANGES Initial Release Review with Richard and SM Updated Typo and Figure10 Reviewed with Esther Issued by Brian Pyun Brian Pyun Brian Pyun Notes ───────────────────────────────────────────────────────────────────────────── Silicon Mitus cannot assume any responsibility for the consequence of use of information furnished nor for any infringement of patents or other rights of third parties which may result from its use. No circuit patent licenses are implied. Silicon Mitus reserves the right to change the circuitry and specifications without notice at any time. This publication supersedes and replaces all information previously supplied. Silicon Mitus products are not authorized for use as critical components in life support devices or systems without the express written approval of Silicon Mitus. © 2017 Silicon Mitus, Inc. - Printed in Korea - All Rights Reserved © 2017 Silicon Mitus, Inc. December 2017 – Rev0.0.2 www.siliconmitus.com 19 / 19
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Warning : Info object (155 0 obj) not found at 1315165EXIF Metadata provided by EXIF.tools