Lanzar Vibe VIBEX2 User’s Manual X2
User Manual: Lanzar Vibe VIBEX2 User’s Manual Troubleshoot Lanzar Vibe VIBEX2 |
Open the PDF directly: View PDF .
Page Count: 10
Download | |
Open PDF In Browser | View PDF |
www.lanzar.com INTRODUCTION FEATURES: 1 FUNCTIONS 1. SIGNAL INPUTS To be connected to the output of the source unit. 2. LOW PASS SUBWOOFER OUTPUT TERMINALS To be connected to the subwoofer channel amplifier left/right inputs. 3. HIGH PASS CHANNEL OUTPUT TERMINALS To be connected to the channel amplifier left/right inputs. 4. FUSE This crossover uses a 1-amp,blade-type fuses for protection from power surges or a short circuit. 5. POWER INPUT TERMINAL (12V) To be connected to the positive terminal of your vehicle battery or other constant +12V source. 6. REMOTE TURN-ON INPUT TERMINAL (REMOTE) To be connected to the remote control wire or antenna lead of the source unit for remote ON/OFF. 7. GROUND INPUT TERMINAL To be wired to the vehicle's chassis ground. 8. POWER INDICATOR This indicator lights up when the internal switching power supply is activated and the unit is operational. 2 FUNCTIONS 9. HIGH PASS GAIN CONTROL For adjusting the channel output signal level. 10. SUBWOOFER STEREO/MONO SWITCH For selection of stereo or mono mode subwoofer output. 11. HIGH-PASS FREQUENCY SELECTOR For selection of high-pass crossover frequency between 80 Hz and 2.5KHz 12. PHASE INVERTER Position the switch to the "180" position shifts the subwoofer output signals 180 degrees out-of-phase relative to the front and rear output signals. 13. BASS-BOOST LEVEL CONTROL (45Hz) For increasing the Bass boost level up to +12dB. 14. LOW PASS SUBWOOFER FREQUENCY SELECTOR For selection of the low-pass crossover frequency for the subwoofer channel between 35 Hz and 400 Hz. 15. SUBWOOFER OUTPUT LEVEL REMOTE CONTROL TERMINAL. To be connected to the remote control for exclusive maneuver of the subwoofer output level, and the subwoofer output level control on the unit ("16" below) is bypassed. 16. LOW PASS SUBWOOFER OUTPUT GAIN CONTROL For adjusting the subwoofer channel output signal level. 3 ELECTRICAL & AUDIO CONNECTIONS 4 ELECTRICAL & AUDIO CONNECTIONS Precautions 1. To prevent short circuits, be sure to disconnect the negative battery ground lead before wiring the system up. 2. When you finish the installation, be sure to make one more check to be sure everything is done correctly. 3. Reinstate all car parts that were removed. 4. Reconnect the negative battery ground lead. Primary Wiring Descriptions ELECTRICAL DESCRIPTION PRIME CONNECTION 12V BATTERY + Connect to the positive battery terminal (constant + 12V source) GROUND GROUND - Connect to the vehicle's chassis ground (check for good ground) REMOTE REMOTE B+(12V) Connect to the remote control wire(or the electrical antenna) of the car radio/cassette deck INPUT RADIO/TAPE PLAYER TO CROSSOVER MODULE Connect from pre-amp output of radio/tape player (or CD) into HIGH PASS OUTPUT CROSSOVER MODULE TO ANY AMPLIFIER Connect from "high-pass output" of CROSSOVER module to any amplifier input. LOW PASS OUTPUT CROSSOVER MODULE TO SUB-WOOFER AMPLIFIER Connect from low-pass sub-woofer output of CROSSOVER to sub-woofer amplifier input. 5 NOISE CHECK & SYSTEM ADJUSTMENT 6 TROUBLE SHOOTING GUIDE 7 INSTALLATION INSTALLATION 8 SPECIFICATIONS SPECIFICATIONS Power source: 14.4 volts DC negative ground Input current 0.5 amp max Distortion: 0.01% THD at 1 V output level Frequency response: 10Hz-30KHz ±3 dB S/N ratio (A weighted): >95dB Separation: 60 dB Crossover frequencies (continuously variable): Low-pass: 35-400 Hz High-pass: 80-2.5KHz Crossover slope rate: 12 dB per octave 2nd Order Butter worth Subwoofer boost: Single octave + 12dB at 45 Hz Input impedance : > 10K Ohms Output impedance <1K Ohms Output voltage level: 5 volts max Dimensions: 160mm (W) x 130mm (D) x 37mm (H) FEATURES AND SPECIFICATIONS SUBJECT TO CHANGE AND / OR IMPROVEMENT WITHOUT NOTICE. 9
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2005:02:01 11:52:25 Producer : Apogee Series3 Pilot v1.0u1 Modify Date : 2010:02:01 17:40:59+08:00 Page Count : 10EXIF Metadata provided by EXIF.tools