Dragino Technology DRAGINOMS12 802.11b/g wireless sensor node User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1481816
Application ID	mKqygm5IizYVQxFL4ypeVw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	25.62kB (320274 bits)
Date Submitted	2011-06-13 00:00:00
Date Available	2011-06-13 00:00:00
Creation Date	2011-05-24 11:52:46
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2011-05-24 11:52:46
Document Title	Microsoft Word - user manual.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	zmp

www.dragino.cn
MS12 User Manual
1/
www.dragino.cn
2.1
2.2
2.3
2.4
Introduce ..................................................................................................................................3
Configure the device via GUI...................................................................................................4
Access the GUI......................................................................................................................4
Configure Wifi parameters .................................................................................................4
Network setting....................................................................................................................5
System Status:.......................................................................................................................6
Securing the MS12 ..................................................................................................................6
Attaching the current clamp....................................................................................................7
Connecting the clamp sensor cable ........................................................................................7
Powering Up ............................................................................................................................7
2/
www.dragino.cn
1 Introduce
This Article
This article is the user manual for the MS12 wireless sensor node. This article describes how
to configure the MS12 to use in different wireless mode and how to use MS12 as a wireless
power meter.
3/
www.dragino.cn
2 Configure the device via GUI
2.1 Access the GUI
The MS12 GUI is a modified GUI version from LUCI, you can access its GUI very easy from
your PC. Connect your PC to its LAN port and set your PC to DHCP. It will automatically get
the ip address which should be in the 192.168.255.1/24 network.
Then in your PC, use your browser to access the IP 192.168.255.1 and you will be redirected
to the GUI of MS12
2.2 Configure Wifi parameters
In the wifi setting page, you can configure the device to connect to your AP via Wifi.
The setting includes:
ESSID: The SSID refers to a wireless network name and is contained in a field in certain wireless
management frames. SSID is sometime called ESSID (Extend Service Set IDentifier). Put your
ESSID here. You can get the ESSID info from your AP.
Encryption: choose the encryption method of your AP. Option include: no encryption, WEP,
WPA-PSK, WPA2-PSK, WPA-PSK/WPA2-PSK mixed mode.
Web-key or WPA passphrase: the encryption key of your AP.
Input the correct ESSID and encryption detail then your MS12 should be able to connect to your
AP.
4/
www.dragino.cn
2.3 Network setting
The network page include the network setting for the LAN interface and wifi interface.
Local Network setting:
IPv4-Address:
ip address of the LAN port
IPv4-Address:
Netmask of the LAN port
IPv4-Gateway (optional): configure the default gateway of LAN port
DNS-Server (optional): Configure DNS server of LAN port
Internet Connection:
Protocol:
for the wifi interface, you can choose DHCP, PPPoE, manual(static IP), or
PPTP
5/
www.dragino.cn
2.4 System Status:
The system status page shows the system status of MS12.
3 Securing the MS12
Disconnect all cables from the Fluksometer. Find a suitable location near the fuse box to install the
Fluksometer. Secure the Fluksometer with the plastic cable tie.
6/
www.dragino.cn
4 Attaching the current clamp
For safety reasons, switch off the main electricity supply. For a single phase supply, attach the
current clamp to one of the two cables running from the electricity meter to the fuse box. Close the
clamp firmly.
5 Connecting the clamp sensor cable
Connect the cable from the current clamp to the MS12's input port. Take care of connecting the
black and red cable as shown in the drawing on the left. Only apply gentle force when fastening
the two screws.
6 Powering Up
Switch the main electricity supply back on. Activate the MS12 by connecting the power plug.
Welcome, you are now part of Flukso community; you should be able to check your power status
in Flukso website: www.flukso.net.
NOTE:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
7/
www.dragino.cn
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
Warning: According to ERC RECOMMENDATION 70-03, Frequency
2400-2483.5 MHz can be used in EU member states and EFTA
countries except France.
8/

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c320 44.284297, Sun Apr 15 2007 17:19:00
Format                          : application/pdf
Creator                         : zmp
Title                           : Microsoft Word - user manual.doc
Create Date                     : 2011:05:24 11:52:46+08:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2011:05:24 11:52:46+08:00
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Document ID                     : uuid:221edf23-da7c-4cf2-ae01-e0feb5a1b759
Instance ID                     : uuid:b22bee8e-b279-4591-94d1-bf2e90d1d38b
Page Count                      : 8
Author                          : zmp

EXIF Metadata provided by EXIF.tools