Duali ITOUCHPOPV2 SMART CARD READER User Manual

Duali Inc. SMART CARD READER Users Manual

Users Manual

Copyright ⓒ 2014 DUALi Inc. All rights reserved. You are strictly prohibited to copy, disclose, distribute, or use this document in part or as a whole for any purposes other than those for which this document is disclosed. This documentis copyrighted and contains confidential information and other intellectual property rights of DUALi Inc. Any unauthorized use, copy, disclosure or distribution constitutes infringement of DUALi’s intellectual property rights. DUALi Inc. Document Number: EP01-14-004 Document Version: 1.0 Last Revised Date: 11th Dec. 2014 ITOUCH_POP2 Specification
FCC STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: SWUITOUCHPOPV2 WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. RF EXPOSURE WARNING! This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
DUALi Inc. reserves the right to make changes to its applications or services or to discontinue any application or service at any time without notice. DUALi provides customer assistance in various technical areas, but does not have full access to data concerning the use and applications of customer's products. Therefore, DUALi assumes no liability and is not responsible for customer applications or software design or performance relating to systems or applications incorporating DUALi products. In addition, DUALi assumes no liability and is not responsible for infringement of patents and/or any other intellectual or industrial property rights of third parties, which may result from assistance provided by DUALi. Composition of the information in this manual has been done to the best of our knowledge. DUALi does not guarantee the correctness and completeness of the details given in this manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since, despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips. We have our development center in South Korea to provide technical support. For any technical assistance can contact our technical support team as below; Tel: +82 31 213 0074 e-mail : lab@duali.com
iTOUCH_POP2 Product Specification ` Version. 1.0 DUALi Inc. (http://www.duali.com) 3 Revision History  2014.12.11 (Ver. 1.0) : Release
iTOUCH_POP2 Product Specification ` Version. 1.0 DUALi Inc. (http://www.duali.com) 4Contents 1 Introduction ............................................................................................................................... 5 2 Components Confirmation ......................................................................................................... 6 2.1 Product Components ....................................................................................................... 6 2.2 Block Diagram ................................................................................................................ 7 2.3 Block Diagram specification ............................................................................................. 8 2.4 Exterior ........................................................................................................................... 9 2.5 PCB .............................................................................................................................. 1 0 2.6 Product Size ................................................................................................................. 11 3 Power & Interface Specification ............................................................................................... 12 3.1 Power Specification ....................................................................................................... 12 3.2 Electric Current Specification ......................................................................................... 12 3.3 RS-232 Interface Specification ....................................................................................... 12 3.4 USB Interface Specification ........................................................................................... 12 3.5 TCP/IP Interface Specification ....................................................................................... 12 3.6 WI-FI Interface Specification .......................................................................................... 12 4 Configuration for Door Lock Control ......................................................................................... 13 4.1 POP + LOCK ................................................................................................................ 13 4.2 POP + PDU + Deadbolt Lock ......................................................................................... 14 4.3 POP(RS-485) + PDU + Deadbolt Lock ........................................................................... 14 5 Connector Specification .......................................................................................................... 15 5.1 J6 (MINI USB) – USB_OTG (Outside) ............................................................................ 15 5.2 J17 (USB A TYPE) – USB_HOST (Outside) ................................................................... 15 5.3 J8 (2mm ,3-PIN DIP TYPE, RIGHT Angle) – UART ........................................................ 15 5.4 J7 (1.25mm, 4-PIN SMD TYPE, RIGHT Angle) - DEBUG UART ..................................... 15 5.5 J9 (2mm ,4-PIN DIP TYPE, RIGHT Angle) - RS-485 (Outside) ........................................ 16 5.6 J11 (2mm, 7-PIN DIP TYPE, RIGHT Angle) - DOOR (Outside) ....................................... 16 5.7 J12 (2mm, 7-PIN DIP TYPE, RIGHT Angle) - WD_DATA (Outside) ................................. 16 5.8 J4 (2.5mm 2PIN DIP, RIGHT Angle) - POWER (Outside) ............................................... 16 6 Usage Environment ................................................................................................................ 17 6.1 Recommendable Operating Environment ....................................................................... 17 6.2 Recommendable Storage Environment .......................................................................... 17 7 Warning and Notice ................................................................................................................ 17 8 Certification ............................................................................................................................ 17
iTOUCH_POP2 Product Specification ` Version. 1.0 DUALi Inc. (http://www.duali.com) 51 Introduction iTOUCH pop2 is designed as a wall-mounted smartcard reader suitable for time-attendance, access control, ID check, self-check-in, self-payment system based on Android O/S. iTOUCH pop2 communicates with PC or controller via USB ,TCP/IP, WiFi(wireless LAN) or Bluetooth(option). User can develop their own program by using Android Jellybean CPU 32bit ARM-CORTEX A5 RISC processor Operating frequency Normal. 625MHz Up to 833MHz Working Memory DDR3 (4Gbit x 2) Program Memory Nand flash (4Gbyte) OS Linux3.0.31 or better, Android 4.2.2 Jellybean Network 10/100M Ethernet POE Option Display 480*272 RGB (16.7M colors) with 4.3inch touch panel 480*3(RGB)*272 Camera I/F 1/4-inch 5Mp SOC Digital image sensor 5M Pixels,Auto Focus Option SAM I/F 1 SAMs supported ISO-7816 Sound Stereo Audio Codec Speaker Stereo Output with 1Watts 1ea Serial Comm. RS232 1ch with 5V power (Control outdoor sound) RS232 1ch, RS485 1ch 3ch. Wiegand D0, D1, LED(in) OUTPUT SD/MMC Card Slot Micro SD memory card 1Slot USB OTG USB 2.0 OTG 1ch. USB Host USB 2.0 Host 1ch. RF PN512 with AMP Button 4 Keys Door control I/F Door status check sensor, Open Switch Relay(NO, NC, COM), Secure Lock(RS485), Output(PDU)
iTOUCH_POP2 Product Specification ` Version. 1.0 DUALi Inc. (http://www.duali.com) 6WIFI Wireless LAN Module IEEE 802.11n/e/i standards up to 150Mbps Option Operating Powers Min 9V, Max 28V (12V DC adaptor) 2 Components Confirmation 2.1 Product Components ① ② ③ ① Reader unit ② WALL Fixer Bracket ③ Screw (2.5*4 / 4 EA) ④ Cable (Provide as your favor) 1) Door cable 2) Wiegand cable 3) PWR cable 4) RS-232 cable 5) RS-485 cable ⑤ 12V DC adaptor  Please use the approved adapter that satisfies the LPS
iTOUCH_POP2 Product Specification ` Version. 1.0 DUALi Inc. (http://www.duali.com) 7 2.2 Block Diagram TFT LCD(4.3”) 1677 Color Touch pad DC/DC CONVERTER CAMERA Module KEYPAD (4ea) Ethernet Micro SD CARD DOOR I/F RS-485 DC INPUT (9V~28V) RF/SAM Module PN512 Speaker USB HUB SAM Card *1 RS-232 RS-232 32bit ARM Cortex-A5 RISC Processor DDR3 (1GByte) Battery Nand Flash (4GByte)Wiegand USB OTG Sound Codecs WIFI USB Host
iTOUCH_POP2 Product Specification ` Version. 1.0 DUALi Inc. (http://www.duali.com) 82.3 Block Diagram specification  CPU: ARM CORTEX 32-bit A5 RISC processor TCC8925  Program & Data Memory: NAND Flash 4Gbyte for program running & file system.  Operation Memory: 1Gbyte DDR3 SDRAM for rapid operating process  LCD: Wide 4.3-inch (16.7M Color TFT LCD) with Touch panel.  Camera: Includes Auto Focus and LED for light  Speaker: 1W / 8ohm speaker is embedded.  RF Module: Using PN512 (Serial Interface on board) and supporting R/W ISO-14443 A/B cards, Mifare, Felica, NFC.  SAM Card: It has 1 SAM card slot supporting ISO 7816 and it’s controlled by RF Module part.  DC INPUT: 9V~24V, Power consumption is 10W. Required to use 9V-2A, 12V-1.5A, 24V-700mA adaptor or SMPS.  SD CARD Slot: It has 1 Micro SD Card Slot for Memory extension.  Ethernet: Supports up to 100Mbps.  Serial Interface: 1 RS-485, 2 RS-232 port communication interfaces.  USB OTG : 1 USB OTG  USB HOST: 1 USB Host. These can be sued for extending optional functions such as memory, RF reader.  Door Interface: There are RELAY control part for door control, Door open & close status control Input and Exit switch status control Input part. For Secure locking, iTOUCH pop2 must be connected to IO Controller via RS-485. In case of using PDU, 24V LOCK is possible.  Wi-Fi: Optional  Battery: Use recharge/discharge-able battery to keep RTC. Discharge after 200 hours (8days).
iTOUCH_POP2 Product Specification ` Version. 1.0 DUALi Inc. (http://www.duali.com) 92.4 Exterior < Front > < Rear >
iTOUCH_POP2 Product Specification ` Version. 1.0 DUALi Inc. (http://www.duali.com) 102.5 PCB - MAIN Board DC 12V Wiegand Debug Ethernet Board RS-232 SAM USB Slave USB Host SD Card Speaker Door ControlRS-485 CAMERA FLASH LED KEY 4EA LCD
iTOUCH_POP2 Product Specification ` Version. 1.0 DUALi Inc. (http://www.duali.com) 11- LAN Board - RF Board 2.6 Product Size - ITOUCH_POP2 (mm) : 185(W) *108(H) * 20.5(D) - Thickness (PCB) MAIN Board : 1.0T RF Board : 1.0T LAN Board : 1.0T
iTOUCH_POP2 Product Specification ` Version. 1.0 DUALi Inc. (http://www.duali.com) 123 Power & Interface Specification 3.1 Power Specification - 12V : 1.5A or above - 24V : 700mA or above 3.2 Electric Current Specification - 12V : average 400mA - 12V : Max 550mA 3.3 RS-232 Interface Specification - 8 Data, 1 Stop, No Parity - Communication speed: Start with 115200 bps 3.4 USB Interface Specification - USB 1.1 Full Speed(12Mbps) 3.5 TCP/IP Interface Specification - 10B / 100B both supported 3.6 WI-FI Interface Specification - IEEE 802.11n/e/i standards.
iTOUCH_POP2 Product Specification ` Version. 1.0 DUALi Inc. (http://www.duali.com) 134 Configuration for Door Lock Control 4.1 POP + LOCK J9 – DOOR PIN Specification 1 RELAY Normal Close 2 RELAY Normal Open 3 RELAY COMMOM 4 Door SW 5 GND 6 DOOR STATUS 7 GND LOCK PWR DC+ (12V or 24V) GND LOCK COMMON CONNECTION NORMAL OPEN LOCK(Secure, open when powered) NORMAL CLOSE LOCK(Safe, close when powered) EXIT SENSOR LOCK Normal Close Type
iTOUCH_POP2 Product Specification ` Version. 1.0 DUALi Inc. (http://www.duali.com) 144.2 POP + PDU + Deadbolt Lock 4.3 POP(RS-485) + PDU + Deadbolt Lock
iTOUCH_POP2 Product Specification ` Version. 1.0 DUALi Inc. (http://www.duali.com) 155 Connector Specification 5.1 J6 (MINI USB) – USB_OTG (Outside) PIN Specification Description 1 USB 5.0V 5V not available 2 USB D- 3 USB D+ 4 ID 5 GND 5.2 J17 (USB A TYPE) – USB_HOST (Outside) PIN Specification Description 1 VDD 5.0V 2 USB D- 3 USB D+ 4 GND 5.3 J8 (2mm ,3-PIN DIP TYPE, RIGHT Angle) – UART - 20017WR-03 (YEONHO) PIN Specification Description 1 RS-232 TXD 2 RS-232 RXD 3 GND 5.4 J7 (1.25mm, 4-PIN SMD TYPE, RIGHT Angle) - DEBUG UART - 12505WR-04 (YEONHO) PIN Specification Description 1 NC 2 RS-232 TXD 3 RS-232 RXD 4 GND
iTOUCH_POP2 Product Specification ` Version. 1.0 DUALi Inc. (http://www.duali.com) 16 5.5 J9 (2mm ,4-PIN DIP TYPE, RIGHT Angle) - RS-485 (Outside) - 20017WR-04 (YEONHO) PIN Specification Description 1 RS-485 + 2 RS-485 - 3 Terminating resisters Resistor 4 Terminating resisters Resistor 5.6 J11 (2mm, 7-PIN DIP TYPE, RIGHT Angle) - DOOR (Outside) - 20017WR-07 (YEONHO) PIN Specification Description 1 Relay C 2 Relay O 3 Relay COM 4 Door_sw 5 GND 6 Door_sta 7 GND 5.7 J12 (2mm, 7-PIN DIP TYPE, RIGHT Angle) - WD_DATA (Outside) - 20017WR-07 (YEONHO) PIN Specification Description 1 PWR_IN 2 NC 3 GND_POWER 4 WD_DATA0 OUTPUT 5 WD_DATA1 OUTPUT 6 LED_IN INPUT 7 BUZ_IN INPUT 5.8 J4 (2.5mm 2PIN DIP, RIGHT Angle) - POWER (Outside) - YMAW025-02 (YEONHO) PIN Specification Description 1 PWR_IN 2 GND_POWER
iTOUCH_POP2 Product Specification ` Version. 1.0 DUALi Inc. (http://www.duali.com) 176 Usage Environment 6.1 Recommendable Operating Environment - Temperature: -10 ~ 60 ℃ - Humidity: 30 ~ 90 % 6.2 Recommendable Storage Environment - Temperature: -20 ~ 80 ℃ - Humidity: 30 ~ 90 % 7 Warning and Notice - Indoor use only (Avoid direct sunlight) - Recommended to use 12V, 700mA or above - Avoid an element like metal or magnetism within 7cm - Do not open the product or adjust the antenna part 8 Certification - KCC, CE, FCC Diameter = 2mm DC + Diameter = 6.5mm DC – (GROUND)

Navigation menu