Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1727218 |
| Application ID | ZE0VDfpNDzn1W5eJVH4+mg== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 37.19kB (464856 bits) |
| Date Submitted | 2012-06-20 00:00:00 |
| Date Available | 2012-06-21 00:00:00 |
| Creation Date | 2011-06-13 10:03:18 |
| Producing Software | Microsoft® Office Word 2007 |
| Document Lastmod | 2011-06-13 10:03:18 |
| Document Title | Manual |
| Document Creator | Microsoft® Office Word 2007 |
| Document Author: | David Snodgrass |
Bentley WiNET Tag User Guide FAS1503 DOC1036 Revision 0 Document Title UltraClenz, LLC Table of Contents Revision History ................................................................................................................................................... 3 Box Contents ....................................................................................................................................................... 4 Overview ............................................................................................................................................................. 4 Installing the Batteries.......................................................................................................................................... 5 Step 1 – Open Tag Enclosure........................................................................................................................... 5 Step 2 – Removing Battery Insulators (Batteries preinstalled) ........................................................................... 5 Step 3 – Installing New Batteries (Batteries not preinstalled)............................................................................. 5 Installing the Tag ................................................................................................................................................. 6 Step 1 – Tag Mounting Location ....................................................................................................................... 6 Step 2 – Attach the Cable to the Tag ................................................................................................................ 6 Step 3 – Fold Cable.......................................................................................................................................... 6 Step 4 – Mount the Tag to the Wall................................................................................................................... 6 Connecting the Tag to the Dispenser ................................................................................................................... 7 Step 1 – Remove Touch-free Dispenser Gearbox ............................................................................................. 7 Step 2 – Install Cable ....................................................................................................................................... 7 Step 3 – Install Gearbox back into the Dispenser .............................................................................................. 8 Testing the Tag.................................................................................................................................................... 8 Step 1 – Setting up Test Equipment ................................................................................................................. 8 Step 2 – Configuring Terminal Emulation Software (HyperTeminal) .................................................................. 8 Step 3 – Conducting the Test ........................................................................................................................... 9 Maintenance ...................................................................................................................................................... 10 Cleaning......................................................................................................................................................... 10 Changing the Batteries ................................................................................................................................... 10 Step 1 – Open Tag Enclosure......................................................................................................................... 10 Step 2 – Replacing Old Batteries .................................................................................................................... 10 Certification and Safety Approvals ..................................................................................................................... 11 FCC ............................................................................................................................................................... 11 Warranty............................................................................................................................................................ 11 Page 2 Document Title UltraClenz, LLC Revision History Revision Date By 01/25/11 MJB Description Initial Release Page 3 Document Title UltraClenz, LLC Box Contents WiNET Radio Tag Coin Cell Batteries (CR2430 - Optional) Detachable Cable User’s Guide Overview The FAS1503 WiNet Tag, when used as a component of the WiNET wireless monitoring solution, relays radio transmissions to both the WiNET Hub (FASxxxx) and the WiNET Gateway (FASxxxx) (see Figure 1). Figure 1. – WiNET Network Topology Page 4 Document Title UltraClenz, LLC Installing the Batteries This procedure will require a small Phillips screwdriver. Step 1 – Open Tag Enclosure With a small Phillips screwdriver, remove the two screws located on the front of the Tag enclosure (see Figure 2). With the screw removed, separate the bottom half of the Tag enclosure from the top half. The Tag will be secured inside the Tag enclosure. Figure 2 – Location of Screws Step 2 – Removing Battery Insulators (Batteries preinstalled) Depending on the configuration ordered, batteries may be preinstalled in the Tag. To prevent power drainage during shipping, insulators may be inserted between the battery contacts and the battery (see figure 3). Remove the battery insulators by gently pulling the insulation away from the battery. Figure 3 Step 3 – Installing New Batteries (Batteries not preinstalled) Depending on the configuration ordered, batteries may not be preinstalled in the Tag. Insert a coin cell battery (CR2430) into the battery holder with the positive (+) side facing toward the contact (see figure 4). Repeat the procedure for the remaining battery holder. Figure 4 Page 5 Document Title UltraClenz, LLC Installing the Tag This procedure will require no tools. Step 1 – Tag Mounting Location In a dry indoor environment, locate an area on a wall next to the dispenser where the Tag will be mounted, preferably to the immediate right or left of the dispenser. Make sure the wall’s surface is clean and free of dirt, dust or grease. NOTE: The Tag is a radio and therefore should not be mounted on or near large metal objects. Doing so may degrade its performance. Step 2 – Attach the Cable to the Tag Insert one end of the detachable cable into the port on the back of the Tag (see Figure 5). Figure 5 Step 3 – Fold Cable Make a 90 fold in the cable at the recessed portion of the back of the enclosure (see Figure 6). Figure 6 If the Tag will be mounted on the left side of the dispenser, fold the cable to the left. If the Tag will be mounted on the right side of the dispenser, fold the cable to the right. Step 4 – Mount the Tag to the Wall Unpeel the protective layer from the two pieces of double sided tape that are located on the back of the Tag. Align the top of the Tag with the top of the dispenser and press the Tag firmly against the wall. Page 6 Document Title UltraClenz, LLC Connecting the Tag to the Dispenser Step 1 – Remove Touch-free Dispenser Gearbox Open the cover of the dispenser and remove the touch-free gearbox. To remove the touch-free gearbox, depress the retention clip located at the top of the touch-free gearbox to unlatch and pivot forward to remove. Step 2 – Install Cable Locate the 6-pin port on the back of the touch-free gearbox and insert the free end of the detachable cable into the port (see figure 7). Figure 7 Insure that the two raised tabs on the top of the cable end are inserted into the corresponding opening in the 6-pin port on the back of the touch-free gearbox (see Figure 8). Figure 8 Page 7 Document Title UltraClenz, LLC Step 3 – Install Gearbox back into the Dispenser To reinstall the touch-free gearbox, place the bottom 2 pivot points into the chassis base and pivot the top towards the chassis until the touch-free gearbox latches and clicks into place. Close the cover. The finished installation should look like Figure 9 below. Figure 9 – Complete Installation Testing the Tag This procedure will require a dispenser with the Tag installed, a hub (optional), a USB to RS485 Network Interface Kit (KIT1101-00), and a gateway attached to a computer running a Terminal Emulation program. Step 1 – Setting up Test Equipment For instruction on how to install and configure the USB to RS485 Network Interface Kit, please refer to DOC1000. Insert the RJ-11 connector, located on the end of the serial cable, into the RS-485 port on the back of the Gateway as shown in figure 10. The other end of the serial cable will be inserted into the RS-485 Data port on the USB to RS485 Network Interface adapter. Figure 10 – Location of serial connection in back of Gateway Insert the USB cable into a USB port on computer. The other end of the USB cable will be inserted into the RS485 Data port on the USB to RS485 Network Interface adapter. Step 2 – Configuring Terminal Emulation Software (HyperTeminal) For instructions on how to configure Terminal Emulation Software (HyperTerminal), please refer to DOC1038 (WiNET Gateway User Guide). With communications established between Gateway and computer, start a terminal session. Press G [enter] until the Gateway events are ON. Press M [enter] until the Monitor Events are OFF. Page 8 Document Title UltraClenz, LLC Step 3 – Conducting the Test With the Gateway properly connected to computer through the USB to RS485 Network Interface adapter, activate the dispenser. Successful events will appear on terminal session as seen in figure 11. Test the connection between the Gateway and the Computer by pressing the letter “t” [enter]. You will see the current date time group that is configured on the Gateway. Figure 11 – Successful Tag Test result A dispense event occurs when a dispenser, equipped with a tag, is activated. Successful dispense events will appear on screen preceded by a lower case letter e and will look like this: e,03000019,025,09520009,2011-01-19 16:14:23 The fields are defined as follows: e = Dispense event 03000019 = Device identification number (unique for each device) 025 = Nonce (Unique identifier - increments by 1 each event) 09520009 = First Responder ID (FRID) 2011-01-19 = Date of event 16:14:23 = Time of event A heartbeat occurs at regularly predetermined intervals and is designed to announce to the gateway that the device is online and operational. Successful heartbeats will appear on screen preceded by a lower case letter h and will look like this: h,03000019,026,09520009,1,001,09520009 The fields are defined as follows: h = Heartbeat 03000019 = Device identification number (unique for each device) 026 = Nonce (Unique identifier - increments by 1 each event) 09520009 = First Responder ID (FRID) 1 = Device Type (1=Tag; 2=Hub) 001 = FRQ (First Responder Link Quality) Page 9 Document Title UltraClenz, LLC 09520009 = Gateway assigned to that network Maintenance Cleaning The exterior can be cleaned with a NON abrasive detergent and a NON abrasive damp (not wet) sponge or cloth. The Tag is splash resistant but not water proof. Changing the Batteries This procedure will require a small Phillips screwdriver and two (2) coin cell batteries (CR2430). Step 1 – Open Tag Enclosure With a small Phillips screwdriver, remove the two screws located on the front of the Tag (see Figure 2). With the screw removed, separate the bottom half of the Tag enclosure from the top half. The Tag will be secured inside the Tag enclosure. Step 2 – Replacing Old Batteries Remove the old batteries by carefully sliding them out of the battery holders. Inset a coin cell battery (CR2430) into each of the battery holders with the positive (+) side facing toward the contact (see figure 4). Page 10 Document Title UltraClenz, LLC Certification and Safety Approvals FCC This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. WARNING: Changes or modifications not expressly approved by UltraClenz, LLC could void the user’s authority to operate the equipment. Regulations "Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication." "This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device." Page 11 Document Title UltraClenz, LLC Warranty This device is warranted against defective materials and workmanship for one year from the date of delivery. Equipment covered by this warranty will be repaired or replaced in the United States and Canada, WITHOUT CHARGE, except for shipping and handling, by our Factory Service Center. When returning equipment for warranty service, you must first call your distributor’s Warranty Service Department for your Return Merchandise Authorization Number (RMA), the RMA must be on your return label, also the shipping charges must be pre-paid and a copy of your receipt must be enclosed. This warranty covers all defects incurred from normal use of the equipment and does not apply in the following cases: a. b. c. Loss or damage to the equipment due to abuse, mishandling, accident or failure to follow mounting instructions. If the equipment is defective as a result of leaking batteries. If the equipment has been serviced or modified by someone other than our authorized agents. THE AFOREMENTIONED IS IN LIEU OF ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR ANY PARTICULAR PURPOSE. IN NO EVENT SHALL THE VENDOR BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL, INDIRECT OR SPECIAL DAMAGES OR LIABILITY, TRANSPORTATION, INSTALLATION OR SUBSTITUTION COSTS, DELAYS, OR FOR ANY OTHER DAMAGES, COSTS, OR EXPENSES INCURRED, IRRESPECTIVE OF HOW THEY OCCUR. THIS WARRANTY SHALL NOT EXTEND TO ANY OTHER PERSON OTHER THAN THE ORIGINAL PUCHASER OF THIS EQUIPMENT OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT. This warranty gives you specific legal rights, and you may also have other rights, which may vary from state to state. This warranty is given with respect to equipment purchased in the United States. This warranty is for the touch-free soap dispenser only, and excludes any representation or warranty with regard to any soap, lotion, solution or other liquid used in the dispenser. Use of improperly formulated soaps, lotions, solutions or other liquids could result, amongst other things, in damage to the dispenser, and/or leakage, which in turn could create conditions leading to personal injury. In no event shall the vendor be liable for any damage or injury caused by any soaps, lotions, solutions or other liquids used in the dispenser. Patent Pending Page 12
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 12 Language : en-US Tagged PDF : Yes Author : David Snodgrass Creator : Microsoft® Office Word 2007 Create Date : 2011:06:13 10:03:18 Modify Date : 2011:06:13 10:03:18 Producer : Microsoft® Office Word 2007EXIF Metadata provided by EXIF.tools