Electronic Controls Design E47-6342-45 MEGA M.O.L.E. User Manual A47 6342 00 2 10

Electronic Controls Design Inc MEGA M.O.L.E. A47 6342 00 2 10

UserManual.wiki >

Electronic Controls Design >

E47-6342-45 User Manual >

User Manual part 2

Contents

User Manual part 2

♦125♦ MEGAM.O.L.E.® Help System Guide 6) Select the Next command button. 7) Select desired text formatting options.

MEGAM.O.L.E.® Help System Guide ♦126♦ 8) Select the Next command button. 9) Select Specification Limits and Units. If these values are violated colored bars will appear in the formatted template cell. Refer to topic Software>Page Tabs>Spreadsheet>Template>Specification Limit Indicators for more information.

♦127♦ MEGAM.O.L.E.® Help System Guide 10) Select the Finish command button to complete the wizard and display the new calculation data in the selected template cell.

MEGAM.O.L.E.® Help System Guide ♦128♦ 5.4.3.2.1.5. Special Value To add or edit Special Value content: 1) Right-click a template cell and a shortcut menu appears. 2) Select Add Content or Edit Content from the shortcut menu and the Add or Change a Calculation wizard appears. When navigating through the wizard, the step list on the left uses a color key to inform the user of the current step, steps that have been completed and remaining steps. Current Completed Remaining 3) Click Special Value. 4) Select the Next command button. 5) Select a Special Value type.

♦129♦ MEGAM.O.L.E.® Help System Guide 6) Select the Next command button. 7) Select desired text formatting options.

MEGAM.O.L.E.® Help System Guide ♦130♦ 8) Select the Finish command button to complete the wizard and display the new calculation data in the selected template parameter column.

♦131♦ MEGAM.O.L.E.® Help System Guide 5.4.3.2.2. Specification Limit Indicators Each Parameter displayed on the Spreadsheet Page Tab can have both Lower and Upper specifications applied. If a specification limit is violated, the software displays a red or blue indicator on the left edge of the Data Table cell. If a USL has been exceeded, that parameter indicator will appear in red (indicating it is above the specification limit). If a parameter is less than the user specified LSL, that parameter indicator will be appear in blue (indicating below the specification limit). Refer to topic Software>Page Tabs>Spreadsheet>Template>Add & Edit Content for information on how to apply LSL and USL values.

♦133♦ MEGAM.O.L.E.® Help System Guide Parameter Labels The Parameter Labels display details associated with the displayed parameters. For example, in the Maximum Y Value parameter, the label is Channel 1. Parameter Units The Parameter Units are the units of measurement for the displayed parameter. For example, in the Maximum Positive Slope parameter, the parameter unit is °C/sec.

MEGAM.O.L.E.® Help System Guide ♦134♦ 5.4.3.4. SPC Flags SPC Flags allow the user to flag parameters so they are displayed on the SPC Page Tab. For each Parameter listed after the User defined Parameters, there is an SPC Flag. To display the parameter data in an X-Bar and R-Chart format, select the desired SPC Flag. Refer to topic Software>Page Tabs>SPC Page Tab for more information.

♦135♦ MEGAM.O.L.E.® Help System Guide 5.4.3.5. Data Run Rows All of the data runs in the Selected working directory are listed on the Spreadsheet Page Tab as individual rows. The first data run uploaded or imported into the directory is on the bottom and the most recent data run is on the top. When any data run row is selected, all of the cells in the entire row are highlighted in purple and blue. The purple cells indicate that the cells can be modified and the blue cells indicate the data cannot be modified. When any individual data cell in a data run row is selected, all of the cells in the entire row are highlighted in green and yellow. The green cells indicate that the cells can be modified and the yellow cells indicate the data cannot be modified. When a data run row is selected, the data for that row will also be displayed in the Sel= row located at the bottom of the data run rows. This row allows the user to easily compare the selected data row to the statistics calculations located below the selected run row. Selected rows and columns can be “copied” by pressing keys [CTRL + C] and then “pasted” [Ctrl + V] into other applications. The data run rows can also be moved into any order desired. This is useful when the user wants to place similar data runs together. To change the order of the data run: 1) Select the number cell of a data run row with the mouse pointer. The row will then become highlighted in purple and blue. 2) Drag the row and drop it to a desired location.

MEGAM.O.L.E.® Help System Guide ♦136♦ 5.4.3.6. Filters There are Filters for each parameter label that user can filter specific data out. Filtering more than one column at a time acts as a Logical AND Function. All conditions of all set filters must be met for data row(s) to remain visible. How to use the Filter function: 1) Click the Filter button to reveal the unique data as populated in that column under that particular parameter label. 2) Select a desired data value to filter, or the two standard filters All and Special. To use the All option: 1) Select All to reset the filter for that column and view all of the data run rows that meet the other column filters.

♦137♦ MEGAM.O.L.E.® Help System Guide To use the Special option: 1) Select Special to select data run rows within a range of values. There are multiple options to select information to filter by clicking the appropriate relational operators option button. The user can either select data from a populated list or type it in the text box on the top of the column. = equal to >= greater than or equal to > greater than <= less than or equal to < less than <> Not equal to 2) Select a data filter by: • Clicking the greater than relational operator option button beside the left data column. • Click a parameter value from the list or type it in the text box. • Click the AND logical operator option button. • Click the less than relational operator option button beside the right data column. • Click a parameter value from the list or type it in the text box. The Clear command button can be selected at any time to clear the selections and the new values can be selected. 3) Click the OK command button to accept the selected data filters or Cancel to return to the Spreadsheet Page Tab without executing the filter request.

MEGAM.O.L.E.® Help System Guide ♦138♦ In this example, the data filtered would be all times between, but not including 13:41:41 and 16:55:30. When the data is filtered, the column header and the Filter Reset button are highlighted in RED. To reset the data run rows to display the entire set of collected data, click the red Filter Reset button.

♦139♦ MEGAM.O.L.E.® Help System Guide

MEGAM.O.L.E.® Help System Guide ♦140♦ 5.4.3.7. Statistics There are shaded rows located on the bottom of the Spreadsheet worksheet, which are the combined calculations for all the data runs that are currently being viewed in the Spreadsheet worksheet display. The following information is the definitions for each Statistics row: • N = Number of samples included in the calculations • Min. = The lowest value in the parameter column. • Max. = The highest value the parameter column. • Avg = The average of all values in the parameter column. • Std. Dev. = The standard deviation of the values in that column. • USL = Upper Specification limit set for that parameter using the Calculation wizard. • LSL = Lower Specification limit set for that parameter using the Calculation wizard. The USL and LSL statistics will only be displayed if there is values set for that parameter

♦141♦ MEGAM.O.L.E.® Help System Guide

♦145♦ MEGAM.O.L.E.® Help System Guide 5.4.4.2. The Data Graph The Data Graph is a display that shows the data collected from the data run overlaid on a graph. The user can analyze and highlight various process features with the tools listed below. Data Graph features:  Time & Temperature Scales  Data Plots  Process Origin  Conveyor Speed Indicator  Time Reference Lines  Temperature Reference Lines  Map Data  Machine Zones and Zone Sizes  Machine Zone Temperatures

MEGAM.O.L.E.® Help System Guide ♦146♦ The Data Graph features are described in the sections that follow. Some of these features are also controlled using the appropriate menu options. Refer to Software>Menu and Tool Commands for more information.

MEGAM.O.L.E.® Help System Guide ♦150♦ 5.4.4.2.2. Data Plots The Data Plots in the Data Graph represent the data for each of the sensors connected to the M.O.L.E. Profiler. Each sensor is represented by a different color that corresponds to the color of its sensor location description in the Data Table. A Data Plot in the Data Graph can be suppressed or restored at any time by clicking the channel check box with the corresponding sensor description in the Data Table. This allows the user to view any combination of the Data Plots or individually. When two or more Data Plots overlap the same values, the Data Plots overwrite each other. For example, if the Data Plot that represents the sensor connected to channel 5 and channel 1 have the same value, the channel 5 Data Plot will only appear unless the user suppresses it. When printing a Data Graph in black and white, suppressing one or more Data Plots is useful for clearing a view of a Data Plot that is obscured by others near it. The Notes tool can also be used to help identify each Data Plot. Refer to topic Software>Menus>Tools>Notes for more information.

♦151♦ MEGAM.O.L.E.® Help System Guide 5.4.4.2.3. Process Origin The Process Origin is a gray vertical line at the left edge of the Data Graph that indicates where the assembly process starts. When Points or Distance units are being used for the Time (X) values, the Time (X) values to the left of the Process Origin are displayed as negative and those to the right as positive in the Time (X)/Temp (Y) Readout. To move the Process Origin: 1) Position the mouse pointer over the Process Origin. 2) When the mouse pointer becomes a , click and hold the left mouse button to drag it left or right releasing the mouse button when the Time (X) Reference line is at the desired location. The X/Y Readout in the Status Bar indicates the true position of the Process Origin while it is being moving. After the mouse button is released, the X-Readout changes to zero at the Process Origin and displays negative numbers for X when the mouse pointer is moved to the left of the Process Origin. Reference line values are automatically adjusted when the Process Origin is moved.

♦153♦ MEGAM.O.L.E.® Help System Guide 5.4.4.2.4. Conveyor Speed Indicator Located at the top of the Process Origin, there is a Conveyor Speed Indicator that displays the speed of the machine conveyor specified in the selected machine recipe. Refer to topic Software>Menus>Machine>Set Machine Information. Conveyor Speed can not be set or viewed after the Data Graph has been magnified. When the mouse pointer is placed over the conveyor speed indicator, it becomes a . This informs the user that they can double-click the indicator to quickly change the conveyor speed in the machine recipe.

MEGAM.O.L.E.® Help System Guide ♦154♦ By changing the conveyor speed from the indicator, the user is modifying the selected machine recipe. This recipe can also be edited using the Software>Menus>Machine>Set Machine Information command on the Machine-Oven menu.

MEGAM.O.L.E.® Help System Guide ♦160♦ 5.4.4.2.10. Machine Zone Temperatures For each defined zone, two zone temperatures can be established using the Set Machine Recipe command on the Machine menu. These temperatures might be upper and lower boundaries for the acceptable range of values in that zone or they might represent the settings of upper and lower heating elements in a process. Zone Temperature Lines appear in the Data Graph as colored bars at the temperature set for each zone. (Zone Temperatures can be displayed only after zone sizes are defined). Upper Zone Temperature Lines appear in the Data graph as solid colored bars and the lower Zone Temperature Lines are dashed.

♦161♦ MEGAM.O.L.E.® Help System Guide 5.4.4.3. The Data Table The Data Table includes various user configured parameter values. Each column after the Sensor Locations allows the user to define parameters using the Template commands. Each row in the Data Table represents the channel sensor data from the M.O.L.E. Profiler. Data Table features:  Sensor Locations  Channel Check Boxes  Data Table Template  Value Pop-up  Specification Limit Indicators

MEGAM.O.L.E.® Help System Guide ♦164♦ 5.4.4.3.1.1. Add & Edit Content Wizard To add or edit template content, the software includes a wizard to guide the user through the related content options. The Data Table template allows three different calculation categories to be displayed. Add & Edit Content wizards:  Temperature Value (Y)  Time Value (X)  Slope (dX/dY)  Temperature (Y) Delta This wizard contains all the related steps to add or edit content to the template. It is recommended to process all steps in order but the software allows you to navigate forward and backward setting options individually. When the minimum options have been selected, Finish command button will become active.

MEGAM.O.L.E.® Help System Guide ♦166♦ 6) Select the Next command button. 7) Select the calculation constraints. These options are the specified area on the Time (X) Axis where the values are to be extracted from. When a constraint is applied, the constraint symbol appears in the header of the calculation. If the Within Magnified Window constraint is selected and the Magnify tool is used to zoom in on a portion of the Data Graph, the Data Table displays the statistics for those values within the magnified window.

♦167♦ MEGAM.O.L.E.® Help System Guide 8) Select the Next command button. 9) Select desired text formatting options.

♦169♦ MEGAM.O.L.E.® Help System Guide 12) Select the Finish command button to complete the wizard and display the new calculation data in the selected template column.

♦171♦ MEGAM.O.L.E.® Help System Guide 6) Select the Next command button. 7) Select the calculation constraints. These options are the specified area on the Time (X) Axis where the values are to be extracted from. When a constraint is applied, the constraint symbol appears in the header of the calculation. If the Within Magnified Window constraint is selected and the Magnify tool is used to zoom in on a portion of the Data Graph, the Data Table displays the statistics for those values within the magnified window.

MEGAM.O.L.E.® Help System Guide ♦172♦ 8) Select the Next command button. 9) Select desired text formatting options.

MEGAM.O.L.E.® Help System Guide ♦174♦ 12) Select the Finish command button to complete the wizard and display the new calculation data in the selected template column.

MEGAM.O.L.E.® Help System Guide ♦176♦ 6) Select the Next command button. 7) Select the calculation constraints. These options are the specified area on the Time (X) Axis where the values are to be extracted from. When a constraint is applied, the constraint symbol appears in the header of the calculation.

♦177♦ MEGAM.O.L.E.® Help System Guide 8) Select the Next command button. 9) Select desired text formatting options.

♦179♦ MEGAM.O.L.E.® Help System Guide 12) Select the Finish command button to complete the wizard and display the new calculation data in the selected template column.

MEGAM.O.L.E.® Help System Guide ♦180♦ 5.4.4.3.1.1.4. Temperature (Y) Delta To add or edit Temperature (Y) Delta content: 1) Right-click a template cell and a shortcut menu appears. 2) Select Add Content or Edit Content from the shortcut menu and the Add or Change a Calculation wizard appears. When navigating through the wizard, the step list on the left uses a color key to inform the user of the current step, steps that have been completed and remaining steps. Current Completed Remaining 3) Click Temperature (Y) Delta and which channel to derive the data from. 4) Select the Next command button. 5) Select a Y-Axis value delta calculation and which channels to you wish to be included in this calculation.

♦181♦ MEGAM.O.L.E.® Help System Guide 6) Select the Next command button. 7) Select desired text formatting options.

♦183♦ MEGAM.O.L.E.® Help System Guide 10) Select the Finish command button to complete the wizard and display the new calculation data in the selected template cell.

♦185♦ MEGAM.O.L.E.® Help System Guide 5.4.4.3.2. Sensor Locations The user can use the Sensor Location cells in the Data Table to describe the location where each sensor is connected to the test product. The color and description indicates which Data Plot on the Data Graph it represents. To change a Sensor location description: 1) Click a Sensor Location cell and type the desired name and press the [enter] key. The Sensor Location description can also be accessed by using the Set Assembly Information command in the Assembly menu.

MEGAM.O.L.E.® Help System Guide ♦186♦ 5.4.4.3.3. Channel Check Boxes The Channel check boxes control whether the associated Data Plot is displayed on the Data Graph and whether the data for that channel are included in the data table calculations. To turn a Data Plot ON or OFF: 1) Click the channel check box beside a Sensor location description to turn it “ON” or “OFF”.

♦189♦ MEGAM.O.L.E.® Help System Guide Target 10-OK features:  Process Parameters: Initial slope, Soak, TAL & Peak parameters derived from the associated paste for the currently selected data run.  Limit Adjustment: Upper and lower specification limits from the selected process for each parameter. The user can adjust these as needed to meet their requirements.  Parameter Values: Actual values derived from the current data run.  Normalized Values: Parameter values in the data run converted to a single number based on a 0-10 scale. The software takes the parameter value then determines where it is in respect to the upper and lower specification limits. If the actual parameter value is in the exact center of the specification limits the normalized value will be a perfect 10.0. Example: The Peak Temperature has an upper limit of 240.0°C and a lower limit of 195.0°C. The software subtracts the upper limit (240.0°C) from the lower limit (195.0°C) equaling (45°C). Then the software creates a 0-10 scale by dividing the 45°C by 20 equaling a scale of 1 point for every 2.25°C. If the actual parameter value for channel 1 is 210.0°C. The software then determine where that value lands on the 0-10 scale. In this case it is 15°C higher than the lower limit so the software divides the 15°C by the scale value of 2.25°C which equals at 6.7 on the scale.

MEGAM.O.L.E.® Help System Guide ♦192♦ 5.4.5. SPC Page Tab The SPC Page Tab displays the specified parameters flagged on the Spreadsheet Page Tab in SPC X-Bar and R charts. Refer to topic Software>Page Tabs>Spreadsheet>SPC Flags for more information. SPC Page Tab features:  Menus and Toolbar buttons  X-Bar Chart  R Chart  Statistics box

MEGAM.O.L.E.® Help System Guide ♦194♦ 5.4.5.2. X-Bar Chart The X-Bar Chart is the graphical chart produced from samples of a flagged parameter on the Spreadsheet Page Tab. The chart uses a rolling average of 2 through 6 sample points. The user can specify the sample points on the SPC Page Tab of the Preferences dialog box. The X-bar is the average of the data samples and the UCL and LCL are calculated using a formula based on the Range data. The calculation numbers vary depending on the data in the Spreadsheet Page Tab. Using the filter function or the hide command allows the user to select the specific data runs to include on the SPC chart.

♦195♦ MEGAM.O.L.E.® Help System Guide 5.4.5.3. R Chart The R Chart is the graphical chart produced from samples of a flagged parameter on the Spreadsheet Page Tab. The R-Bar is the averages of the range samples. If the Sub-Group size on the SPC Page Tab of the Preferences dialog box is set to 1, the R chart becomes a moving range (mR) chart. The moving range is the difference between a specified X value and the one preceding it. The calculation numbers vary depending on the data in the Spreadsheet Page Tab. Using the filter function or the hide command allows the user to select the specific data runs to include on the SPC chart.

MEGAM.O.L.E.® Help System Guide ♦196♦ 5.4.5.4. Statistics Box The Statistics Box reflects the current SPC data from the selected, sorted and filtered data set parameter. Statistics box data: • N = Number of subgroups. • Min. = The lowest data point on the graph. • Max. = The highest data point on the graph. • X-2 bar = The current X-Bar Bar calculation. • Std. Dev.= The Standard Deviation of the selected parameter. • Cp; Cpk = Process capability indeces (Refer to Appendix B for more information).

♦197♦ MEGAM.O.L.E.® Help System Guide 5.5 Menu and Tool Commands 5.5.1. File Menu This section explains how to use all of the Menu and Toolbar button commands. Each of the following sections will list all of the commands specific to each of the menus. Commands in the File menu are used to manipulate and configure data run files. The dimmed menu commands are used in other page tabs.

MEGAM.O.L.E.® Help System Guide ♦200♦ MAP software allows multiple instruments to be connected to a computer at one time. Selecting the Scan for Instruments command button will detect all instruments and display them in the list. If no instrument is detected, the default Demonstration MEGAM.O.L.E.® profiler is displayed. 5) Click the Next command button. 6) Select a machine from the Machine drop down list. If it does not appear in the list click the New command button to create a new machine. Refer to topic Software>Menus>Machine>Create new Machine for more information.

♦201♦ MEGAM.O.L.E.® Help System Guide 7) Set the machine recipe settings such as Conveyor Speed, Zone Temperatures and Temperature units. The software includes features to save and load machine recipe setting files. These files are helpful to quickly load machine information and to ensure they are always the same.

MEGAM.O.L.E.® Help System Guide ♦202♦ 8) Click the Next command button. If no value is specified for the conveyor speed or the default oven temperature values, the software will remind the user to set them. 9) Set the assembly information such as part number, board size, sensor locations and a product image.

♦203♦ MEGAM.O.L.E.® Help System Guide If the user specifies a product image, clicking the Enlarge command button displays the Set Sensor Locations dialog box where the user can specify the locations of each sensor. To move sensor locations, drag the sensor markers to the approximate location where the sensors are attached.

♦205♦ MEGAM.O.L.E.® Help System Guide Once a paste is selected the specifications are displayed on the graph. The software also allows paste specification data to be viewed in a table view by clicking the Table command button.

MEGAM.O.L.E.® Help System Guide ♦206♦ 13) Click the Next command button 14) Set Recording Parameters such as the instrument name, recording interval, start parameters and stop parameters. This step is where the user can also turn a sensor channel ON or OFF, set the sensor location description and sensor type. Refer to section Software>Menus>MOLE>Set Recording Parametersfor detailed information for each setting.

♦207♦ MEGAM.O.L.E.® Help System Guide 15) Click the Next command button. 16) Click the Next command button to send the recording parameters to the instrument.

MEGAM.O.L.E.® Help System Guide ♦208♦ 17) Verify the instrument status. This dialog box displays the health of the M.O.L.E. Profiler such as battery charge, internal temperature, thermocouple temperatures. If the user selects the Show Critical command button the dialog box will only display items that will prevent the user from completing a successful data run. If the I/O module is not connected to the MEGAM.O.L.E.® Profiler, the software will display a warning message that the instrument is not communicating.

♦209♦ MEGAM.O.L.E.® Help System Guide 18) Pass the thermally protected M.O.L.E. Profiler and test product through the process. Refer to topic Basics>Operation>Step 2 - Data Collection for more information. If the M.O.L.E. Profiler already contains a data run, click the Next command button to continue to the next step.

MEGAM.O.L.E.® Help System Guide ♦210♦ 19) Click the Next command button. 20) Select the desired data run and then click the Read command button to read the data run from the M.O.L.E. Profiler. If the user has selected to use the Wireless RF option, select Start real-time RF on the top of the data run list.

♦211♦ MEGAM.O.L.E.® Help System Guide On this step of the wizard, the user has the ability to remove a selected data run from the M.O.L.E. profiler by either selecting the Delete After Reading check box or selecting the Delete command button and removing it before downloading. 21) When the data run has been downloaded, the software will prompt the user to specify a new file name.

MEGAM.O.L.E.® Help System Guide ♦212♦ I 22) When finished, click the Save command button. 23) The software then prompts the user if they want to enter Prediction mode. Entering prediction mode enables the user to change a zone temperature value or the conveyor speed and predict the outcome of that change. Refer to topic Software>Menus>Tools>Prediction for more information. 24) Click the Predict command button to enter Prediction mode or Done to complete the workflow wizard .

MEGAM.O.L.E.® Help System Guide ♦214♦ 4) Select an existing data run. The software automatically highlights the currently selected data run on the Spreadsheet page tab, but the user can select any data run displayed on the list. 5) Click the Next command button. 6) Select the desired instrument from the list box to make active. If there are none listed, click the Scan for Instruments command button to detect all available instruments. MAP software allows multiple instruments to be connected to a computer at one time. Selecting the Scan for Instruments command button will detect all instruments and display them in the list. If no instrument is detected, the default Demonstration MEGAM.O.L.E.® profiler is displayed.

♦215♦ MEGAM.O.L.E.® Help System Guide 7) Click the Next command button. 8) Click the Next command button to send the data listed in the dialog box to the instrument.

MEGAM.O.L.E.® Help System Guide ♦216♦ 9) Verify the instrument status. This dialog box displays the health of the M.O.L.E. Profiler such as battery charge, internal temperature, thermocouple temperatures. If the user selects the Show Critical command button the dialog box will only display items that will prevent the user from completing a successful data run. If the I/O module is not connected to the MEGAM.O.L.E.® Profiler, the software will display a warning message that the instrument is not communicating.

♦217♦ MEGAM.O.L.E.® Help System Guide 10)Pass the thermally protected M.O.L.E. Profiler and test product through the process. Refer to topic Basics>Operation>Step 2 - Data Collection for more information. If the M.O.L.E. Profiler already contains a data run, click the Next command button to continue to the next step.

MEGAM.O.L.E.® Help System Guide ♦218♦ 11) Click the Next command button. 12) Select the desired data run and then click the Read command button to read the data run from the M.O.L.E. Profiler. If the user has selected to use the Wireless RF option, select Start real-time RF on the top of the data run list.

♦219♦ MEGAM.O.L.E.® Help System Guide On this step of the wizard, the user has the ability to remove a selected data run from the M.O.L.E. profiler by either selecting the Delete After Reading check box or selecting the Delete command button and removing it before downloading. 20) When the data run has been downloaded, the software will prompt the user to specify a new file name.

MEGAM.O.L.E.® Help System Guide ♦220♦ I 21) When finished, click the Save command button to complete the workflow wizard.

MEGAM.O.L.E.® Help System Guide ♦222♦ 4) Select the desired instrument from the list box to make active. If there are none listed, click the Scan for Instruments command button to detect all available instruments. MAP software allows multiple instruments to be connected to a computer at one time. Selecting the Scan for Instruments command button will detect all instruments and display them in the list. If no instrument is detected, the default Demonstration MEGAM.O.L.E.® profiler is displayed. 5) Click the Next command button. 6) Select the desired data run and then click the Read command button to read the data run from the M.O.L.E. Profiler. If the user has selected to use the Wireless RF option, select Start real-time RF on the top of the data run list.

♦223♦ MEGAM.O.L.E.® Help System Guide On this step of the wizard, the user has the ability to remove a selected data run from the M.O.L.E. profiler by either selecting the Delete After Reading check box or selecting the Delete command button and removing it before downloading. 7) When the data run has been downloaded, the software will prompt the user to specify a new file name.

MEGAM.O.L.E.® Help System Guide ♦224♦ I 8) When finished, click the Save command button to complete the workflow wizard.

♦225♦ MEGAM.O.L.E.® Help System Guide 5.5.1.2. Open Working Directory The MAP software is a data run manager. The software does not store data run files (.XMG) it allows the user to save them in a directory of their choice. This can be useful to store data runs in different directories based on customer, shift or machine type. To open a working directory: 1) On the File menu, click Open Working Directory. 2) Navigate to the location where the data run files (.XMG) are located. 3) Click the Open command button to select the directory or Cancel to quit the command. This command can be accessed on the Toolbar. Open Working Directory button

♦227♦ MEGAM.O.L.E.® Help System Guide To import .TXT files: 1) On the File menu, point to Import and then select .TXT. 2) Navigate to the file folder where the file(s) to import are located. 3) Select the file to import. 4) Click the Open command button to import and the Data Import Formatter dialog box appears.

MEGAM.O.L.E.® Help System Guide ♦228♦ 5) Select from the formatter options. If the user is not sure if the Text file values are comma or tab separated, the Test command button can be used to test the format to display the data in columns and rows. 6) Click the OK command button to import or Cancel to stop.

♦229♦ MEGAM.O.L.E.® Help System Guide 5.5.1.4. Export The Export command exports a data run into Microsoft Excel. This process automatically launches Excel and inserts the selected data run information. The user can then save it as an Excel file format. To export data run information: 1) On the File menu, point to Export and then select Excel. The data run information is automatically converted to the Microsoft Excel file format. 5.5.1.5. Save Data Run The Save Data Run command saves the any changes made to the selected data run. If the user selects a different page tab or exits the software, any changes made to the selected data run will automatically be saved. To save the current data run: 1) On the File menu, click Save Data Run and the currently selected data run will be saved. This command can be accessed on the Toolbar. Save Data Run button

MEGAM.O.L.E.® Help System Guide ♦230♦ 5.5.1.6. Preferences The Preferences command allows access to property sheet that includes custom setup tasks and global settings for the software.

♦231♦ MEGAM.O.L.E.® Help System Guide The Preferences property sheet includes various tabs associated with the each individual Page Tab and the MAP menus.

♦235♦ MEGAM.O.L.E.® Help System Guide 5.5.1.6.2. Machine To access machine preferences: 1) On the File menu, click Preferences, and then click the Machine tab. Units The user can set the machine conveyor speed and zone size units. These units will be used as the default when setting machine information. Files As the user creates Machine (.OVS) & Recipe (.XMR) files, they are saved to the specified default working directories. Changing the directory locations may be useful when the user would like to share them on a network drive.

MEGAM.O.L.E.® Help System Guide ♦236♦ Report Select the corresponding check box to include the Machine and Recipe settings when printing in Report format.

♦237♦ MEGAM.O.L.E.® Help System Guide 5.5.1.6.3. Assembly To access assembly preferences: 1) On the File menu, click Preferences, and then click the Assembly tab. Units The user can set the board size and component location units. These units will be used as the default when setting assembly information. Files As the user collects assembly board image files, they can be saved to the specified default working directory. When setting assembly information the user can select a product image. The software automatically starts in the directory specified as the default. Changing the directory location may be useful when the user would like to share the images on a network drive.

MEGAM.O.L.E.® Help System Guide ♦238♦ Report Select the corresponding check box to include the Assembly settings when printing in Report format.

♦239♦ MEGAM.O.L.E.® Help System Guide 5.5.1.6.4. Process To access process preferences: 1) On the File menu, click Preferences, and then click the Process tab. Units The user can set the Time and Slope time process parameters extracted from a data run.

MEGAM.O.L.E.® Help System Guide ♦240♦ Files The user can change the location where they store the paste database and Target 10 Specs files to a specified default working directory of their choice. Included with the software is a Paste database file (paste1.psp). As the user creates process recipes the software creates an extension paste file (user1.psp) which is combined with the default paste1.psp file. Changing the directory location may be useful when the user would like to share the paste database on a network drive. If the paste1.psp file is moved to a different location, the user1.psp file must also be copied to the new location. Report Select the corresponding check box to include the Process settings when printing in Report format.

♦241♦ MEGAM.O.L.E.® Help System Guide 5.5.1.6.5. Summary To access summary preferences: 1) On the File menu, click Preferences, and then click the Summary tab. Files The user can decide which default Summary template they wish to use. If a user creates a new Summary template, it can save using the template commands. If the new template is to be used as the default, the new one can be specified in this text box. The specified template will now be loaded every time the program is started. Show The Summary Page Tab is built with cells that are organized into columns and rows. The software allows the user to show and hide the cell Row/Column labels and Grid lines. Selecting the corresponding check boxes to show or hide the labels and cells.

MEGAM.O.L.E.® Help System Guide ♦242♦ Report Select the corresponding check box to include the Summary Page Tab when printing in Report format. Password Select the corresponding check box to password protect the Summary Page Tab and preferences. If password protection has been selected, a dialog box appears prompting the user to enter the current password. The software will then need to be restarted to apply password protection settings. If the default password has not been changed, the current password is Admin. Refer to topic Software>Menus>File>Preferences>Misc>Passwords for more information.

♦243♦ MEGAM.O.L.E.® Help System Guide 5.5.1.6.6. Spreadsheet To access spreadsheet preferences: 1) On the File menu, click Preferences, and then click the Spreadsheet tab. Files The user can decide which default Spreadsheet template they wish to use. If a user creates a new Spreadsheet template, it can save using the template commands. If the new template is to be used as the default, the new one can be specified in this text box. The specified template will now be loaded every time the program is started. Show The Spreadsheet Page Tab is built with cells that are organized into columns and rows. The software allows the user to show and hide the cell Row/Column labels and Grid lines. Selecting the corresponding check boxes to show or hide the labels and cells.

MEGAM.O.L.E.® Help System Guide ♦244♦ Report Select the corresponding check box to include the Spreadsheet Page Tab when printing in Report format. Password Select the corresponding check box to password protect the Spreadsheet Page Tab and preferences. If password protection has been selected, a dialog box appears prompting the user to enter the current password. The software will then need to be restarted to apply password protection settings. If the default password has not been changed, the current password is Admin. Refer to topic Software>Menus>File>Preferences>Misc>Passwords for more information.

MEGAM.O.L.E.® Help System Guide ♦246♦ Password Select the corresponding check box to password protect the SPC Page Tab and preferences. If password protection has been selected, a dialog box appears prompting the user to enter the current password. The software will then need to be restarted to apply password protection settings. If the default password has not been changed, the current password is Admin. Refer to topic Software>Menus>File>Preferences>Misc>Passwords for more information.

♦247♦ MEGAM.O.L.E.® Help System Guide 5.5.1.6.8. M.O.L.E.(r) To access M.O.L.E. preferences: 1) On the File menu, click Preferences, and then click the M.O.L.E.(r) tab. Show The Status bar located on the bottom of the software display can show the status of the M.O.L.E. Profiler Power Pack battery, Internal operating temperature, connected COM port. Select the corresponding check box to display these status indicators. Report Select the corresponding check box to include the M.O.L.E. information when printing in Report format.

MEGAM.O.L.E.® Help System Guide ♦248♦ Update Firmware If a new version of the MEGAM.O.L.E.® Profiler firmware is released by ECD, the user can use the Update Firmware wizard to upgrade to the newest version. To update MEGAM.O.L.E.® Profiler firmware: 1) On the File menu, click Preferences, and then click the M.O.L.E.(r) tab. 2) In the MOLE section, click the Update Firmware command button and the software automatically scans for a selected instrument. If there is no instrument selected, the Select Instrument dialog box appears. 3) Select the OK command button. Updating the MEGAM.O.L.E.® Profiler firmware erases any stored data runs. Make sure they have been downloaded prior to completing this process. 4) Navigate to the file folder where the firmware file *.BIN is located.

♦249♦ MEGAM.O.L.E.® Help System Guide 5) Select the firmware file. 6) Click the Open command button to start updating the firmware. 7) When the update firmware process is complete, select the OK command button.

Navigation menu