Electronic Systems Technology ESTEEM195EA Wireless LAN transceiver User Manual CHAPTER 2

Electronic Systems Technology Wireless LAN transceiver CHAPTER 2

User Manual Appendix B

Download: Electronic Systems Technology ESTEEM195EA Wireless LAN transceiver User Manual CHAPTER 2
Mirror Download [FCC.gov]Electronic Systems Technology ESTEEM195EA Wireless LAN transceiver User Manual CHAPTER 2
Document ID1635890
Application IDazupRjCtfKMAMzcMbXAEmQ==
Document DescriptionUser Manual Appendix B
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize14.07kB (175891 bits)
Date Submitted2012-02-13 00:00:00
Date Available2012-02-13 00:00:00
Creation Date2012-02-09 14:31:28
Producing SoftwareMicrosoft® Word 2010
Document Lastmod2012-02-09 14:31:28
Document TitleCHAPTER 2
Document CreatorMicrosoft® Word 2010
Document Author: Debra Vaughn

APPENDIX B
SPECIFICATIONS
Model 195Ea Specifications
LED Indicators
Power On/Off
Carrier Detect On/Off
Link Status On/Off
Receiver On/Off
Transmitter On/Off
I/O Connectors
Ethernet 10/100Base T
RS-232C Programming/Data Port
RJ-45
RJ-45
Dual Antenna input/Outputs
TNC Reverse Female
Remote Input Power
Power Over Ethernet Cable
Direct Input Power
Optional, Header Screw Connector
Transmiter
5.745 to 5.825 GHz
Software Selectable in 17 Channels
Frequency of Operation
RF Data Rates
6 to 54 Mbps (8 steps)
Tx Peak Output Power
250mW to 1 Watt (Pk) (4-levels)
RF Output Impedance
50 ohms
Receiver
Rx Sensitivity
-72 dBm @54 Mbps to –92 dBm @ 6 Mbps
Frame Error Rate <10%
Power
IEEE 802.3at Power Supply,
48 VDC @ 30 Watts
10 to 28 VDC
250 ma @ 12 VDC
1.25 A @ 12 VDC
Power over Ethernet
Power Connector on Unit
Receive
Transmit
Case
Dimensions
1.9 in. H x 6.7 in. W x 6.2 in. L
Weight
Outdoor Pole Mounting Kit
Other
1.25 lbs.
Optional, EST P/N 195PM
Warranty
1 Year
Temperature Range
Humidity
FCC Type Acceptance
Industry Canada Type Acceptance
-30 to +60 C
95% Non-condensing
Pending
Pending
Specifications Subject to Change Without Notice
Revised: 27 Jan 12
APX B-1
EST P/N AA107A
APPENDIX B
SPECIFICATIONS
Model 195Ea Case Specifications
Model AA20DMEg
Revised: 27 Jan 12
APX B-2
EST P/N AA107A
APPENDIX B
SPECIFICATIONS
Antenna Specifications
Model: AA20DMEa
Applications: Model 195Ea direct case mount
Antenna Type: Omni-Directional, Sleeve dipole
Frequency: 5.735 to 5.835 GHz
Polarization: Vertical
Impedance: 50 ohms
Gain: 4.5 dBi (2.5 dBd)
VSWR: < 1.5:1
Power: 10 W
Front To Back Ratio: n/a
Horizontal Beamwidth: n/a
Vertical Beamwidth: n/a
Antenna Material: Polyurethane Plastic Radome
Recommended Mounting Hardware: n/a
Antenna Connector: TNC-R Male
Flexibility: +/- 20 
Antenna Envelope: 7.36 in. length by .51 in. width
Temperature: -20 to +65 C
Weight: 28.4 grams
Caution
To comply with the FCC
exposure compliance
requirements, a separation
distance of at least ~113
cm must be maintained
between the antenna and
all persons.
AA20DMEa
Model No: AA20Ea
Antenna Type: Omni Directional, DC Grounded
Applications: Fixed base
Frequency: 5.725-5.825 GHz
Polarization: Vertical
Impedance: 50 ohms
Gain: 6 dBi (8 dBd)
VSWR: 1.5:1 Typical
Vertical Beamwidth: 6 degrees @ ½ power
Recommended Mounting Hardware: Pole Mounting Bracket, Supplied
Antenna Connector: TNC male reverse polarity with
18 in. pigtail and weatherproof boot
Maximum Power Input: 25 Watts
Wind Survival: 125 mph
Antenna Envelope: 20.2 in. L x 1.25 in.
Equivalent Flat Plate Area: .06 sq. ft
Lateral Thrust at Rated Wind: 5.2 lbs feet
Radome: White UV resistant fiberglass
Weight: 0.5 lbs.
AA20Ea
Revised: 27 Jan 12
APX B-3
EST P/N AA107A
APPENDIX B
SPECIFICATIONS
Antenna Specifications
Model No: AA205Ea
Applications: Fixed base mounting
Antenna Type: Directional, Linear Polarized Panel, DC grounded,
Integral Bandpass Filter
Frequency: 5.725-5.875 GHz
Polarization: Vertical or Horizontal
Impedance: 50 ohms
Gain: 22 dBi (20 dBd) nominal
VSWR: <1.5:1 nominal
Front to Back Ratio: ≥ 25 dB
Horizontal Beamwidth: 9 degrees @ ½ power
Vertical Beamwidth: 9 degrees @ ½ power
Antenna Material: White UV Resistant Polypropylene
Recommended Mounting Hardware: Adjustable Mounting Bracket
provided for wall mounting or masts between 1 in and 2.75 in. O.D.
Antenna Connector: TNC male reverse polarity with 18 in. pig-tail
and weatherproof boot.
Maximum Power Input: 20 Watts
Antenna Envelope: 14.5 in. length by 14.5 in. height by 1.75 in.
depth
Operating Temperature: -40 to +85 F.
Weight: 3.5 lbs.
Model AA205Ea
Caution
To comply with the FCC
exposure compliance
requirements, a separation
distance of at least ~113
cm must be maintained
between the antenna and
all persons.
Revised: 27 Jan 12
APX B-4
EST P/N AA107A

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 4
Language                        : en-US
Title                           : CHAPTER 2
Author                          : Debra Vaughn
Creator                         : Microsoft® Word 2010
Create Date                     : 2012:02:09 14:31:28-05:00
Modify Date                     : 2012:02:09 14:31:28-05:00
Producer                        : Microsoft® Word 2010
EXIF Metadata provided by EXIF.tools
FCC ID Filing: ENPESTEEM195EA

Navigation menu