Electronic Systems Technology ESTEEM195EG-1 ESTEEM 195Eg User Manual 195Eg Apx B Specifications

Electronic Systems Technology ESTEEM 195Eg 195Eg Apx B Specifications

user manual apxB

APPENDIX B SPECIFICATIONS Model 195Eg Specifications Revised: 2 Jul 08 APX B-1 EST P/N AA107G LED Indicators Power On/Off Receiver On/Off Carrier Detect On/Off Transmitter On/Off Link Status On/Off I/O Connectors Ethernet 10/100Base T RJ-45 RS-232C Programming/Data Port RJ-45 Dual Antenna input/Outputs TNC Reverse Female Remote Input Power Power Over Ethernet Cable Direct Input Power Optional, Header Screw Connector Transmiter Frequency of Operation 2.412 to 2.462 GHz Software Selectable in 11 Channels RF Data Rates 1,2,5.5,6,9,11,12,18,24,36,48, & 54 Mbps Fixed or Auto Scaling Tx Peak Output Power 1 Watt RF Output Impedance 50 ohms Receiver Rx Sensitivity -68 dBm @54 Mbps to –89 dBm @ 1 Mbps Frame Error Rate <10% Power Power over Ethernet IEEE 802.3af Standard Power Supply, 48 VDC @ 13 Watts Power Connector on Unit 10 to 16 VDC Receive 320 ma @ 12 VDC Transmit 1000 ma @ 12 VDC Case Dimensions 1.9 in. H x 6.7 in. W x 6.2 in. L Weight 1.25 lbs. Outdoor Pole Mounting Kit Optional, EST P/N 195PM Other Warranty 1 Year Temperature Range -30° to +60° C Humidity 95% Non-condensing FCC Type Acceptance ENPESTEEM195EG-1 Industry Canada Type Acceptance 1457A-195EG The GPL source code contained in this product is available as a free download from the following: ftp://ftp.esteem.com/opensource/gplsourcepackage.tar.bz2 If you would like a copy of the GPL source code contained in this product shipped to you on CD, please send $9.99 to 415 N. Quay Street, Kennewick, WA 99336 which covers the cost of preparing and mailing a CD to you. Specifications Subject to Change Without Notice
APPENDIX B SPECIFICATIONS Model 195Eg Case Specifications Revised: 2 Jul 08 APX B-2 EST P/N AA107G
APPENDIX B SPECIFICATIONS Antenna Specifications Revised: 2 Jul 08 APX B-3 EST P/N AA107G Model No: AA01S Antenna Type: Omni-Directional, variable angle rubber duck Applications: Direct mount Frequency: 2400 to 2485 MHz Polarization: Vertical Impedance: 50 ohms Gain: Unity VSWR: < 1.5 Front to Back Ratio: n/a Horizontal Beamwidth: n/a Vertical Beamwidth: n/a Antenna Material: Rubber duct whip. Mounting Hardware: n/a Antenna Connector: TNC-R Male Antenna Envelope: 4.25 in. length by 1.75 in width Weight: .08 lbs. Model: AA20DMEg Applications: Model 195Eg direct case mount Antenna Type: Omni-Directional, Sleeve dipole Frequency: 2400 to 2485 MHz Polarization: Vertical Impedance: 50 ohms Gain: 5 dBi (3 dBd) VSWR: < 2:1 Power: 10 W Front To Back Ratio: n/a Horizontal Beamwidth: n/a Vertical Beamwidth: n/a Antenna Material: Polyurethane Plastic Radome Recommended Mounting Hardware: n/a Antenna Connector: TNC-R Male Flexibility: +/- 20 ° Antenna Envelope: 8.28 in. length by .54 in. width Temperature: -40 to +70 C° Weight: 33 grams Model AA01S Model AA20DMEg Caution Omni-directional antenna should not be located within 20 cm of personnel. Caution Omni-directional antenna should not be located within 20 cm of personnel.
APPENDIX B SPECIFICATIONS Antenna Specifications Revised: 2 Jul 08 APX B-4 EST P/N AA107G Model No: AA20Eg Antenna Type: Omni Directional, DC Grounded Applications: Fixed base Frequency: 2400 to 2500 MHz Polarization: Vertical Impedance: 50 ohms Gain: 6 dBi (4dBd) VSWR: 1.2:1 Typical Front to Back Ratio: n/a Horizontal Beamwidth: n/a Vertical Beamwidth: 40 degrees @ ½ power Antenna Material: Brass radiator, UV inhibited fiberglass enclosed Mounting Hardware: Base to Mast, Supplied. Antenna Connector: TNC-R Male with 36in. pig-tail. Antenna Envelope: 12 in. length by 1 in. diameter Weight: 1.5 lbs. Mounting Bracket Model AA20Eg Caution To comply with the FCC exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna and all persons.
APPENDIX B SPECIFICATIONS Antenna Specifications Revised: 2 Jul 08 APX B-5 EST P/N AA107G Model No: AA203Eg Antenna Type: Directional, DC grounded Applications: Fixed base. Frequency: 2400 to 2485 MHz Polarization: Vertical or Horizontal Impedance: 50 ohms Gain: 6 dBi (4 dBd) VSWR: < 1.5 Front to Back Ratio: >23 dB Horizontal Beamwidth: 55 degrees @ ½ power Vertical Beamwidth: 55 degrees @ ½ power Antenna Material: Sealed in UV stable fiberglass enclosed radome Mounting Hardware: Stainless steel U bolts (included) for mounting up to 1 5/8 in. diameter pipe. Antenna Connector: TNC-R Male with 36in. pig tail Maximum Power Input: 5 Watts Antenna Envelope: 4.5 in. length by 3 in. diameter Windload (RWV): 125 mph Lateral Thrust at Rated Wind: 5.8 lbs. Wind Surface Area: 0.060 ft2 Weight: 1 lbs. Model AA203Eg Caution To comply with the FCC exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna and all persons.
APPENDIX B SPECIFICATIONS Antenna Specifications Revised: 2 Jul 08 APX B-6 EST P/N AA107G Model No: AA204Eg Applications: Fixed base mounting Antenna Type: 2.4 GHz ISM, Directional, DC Grounded, Parabolic Grid Frequency: 2400-2485 MHz Polarization: Vertical or Horizontal Impedance: 50 ohms Gain: 19 dBi (17 dBd) nominal VSWR: < 1.5:1 nominal Front to Back Ratio: >24 dB Horizontal Beamwidth: 16 degrees @ ½ power Vertical Beamwidth: 11 degrees @ ½ power Antenna Material: Zinc plated cold rolled steel with polyester power coat finish Recommended Mounting Hardware: Standard U-bolt steel mast clamp complete with mounting hardware. Designed for masts of up to 2.5 in. O.D. Antenna Connector: TNC-R Male with 36 in. pig-tail Maximum Power Input: 10 Watts Wind Survival: 100 mph Wind Load: 16 mph Antenna Envelope: 34 in. length by 17 in. width by 11 in. height Weight: 3 lbs. Use of the AA204Eg, directional antenna is limited to fixed point-to-point applications only. In accordance with FCC Section 15.247(b)iii, this antenna must be professionally installed. The installer must ensure the system is used exclusively for fixed, point-to-point applications and the ESTeem Model 195Eg is set for 0.25 Watts output power (Power Level = Min). Model AA204Eg Caution To comply with the FCC exposure compliance requirements, a separation distance of at least 50 cm must be maintained between the antenna and all persons.
APPENDIX B SPECIFICATIONS Antenna Specifications Revised: 2 Jul 08 APX B-7 EST P/N AA107G Model No: AA20E Antenna Type: Omni Directional, DC Grounded Applications: Fixed base Frequency: 2400 to 2500 MHz Polarization: Vertical Impedance: 50 ohms Gain: 6 dBd VSWR: < 1.5 Front To Back Ratio: n/a Horizontal Beamwidth: n/a Vertical Beamwidth: 35 degrees @ ½ power Antenna Material: Copper alloy radiator, UV inhibited fiberglass enclosed Mounting Hardware: Aluminum bracket for mounting to 1 ¼ to 2 in. diameter mast included. Antenna Connector: N female reverse polarity. Antenna Envelope: 20 in. length by 1.35 in. diameter Weight: 2 lbs. Only pre-made coax cables from the factory used in conjunction with either the AA20E omni-directional and AA203ES or AA204ES directional antennas meet all FCC Section 15.247(b) EIRP maximum power requirements. See Chapter 8 for details on maximum cable lengths. Model AA20E Mounting Bracket Caution To comply with the FCC exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna and all persons
APPENDIX B SPECIFICATIONS Antenna Specifications Revised: 2 Jul 08 APX B-8 EST P/N AA107G Model No: AA203ES Antenna Type: Directional, 6 element yagi, DC grounded Applications: Fixed base. Frequency: 2400 to 2483.5 MHz Polarization: Vertical or Horizonal Impedance: 50 ohms Gain: 7 dBd VSWR: < 1.5 Front To Back Ratio: 13.5 dB Horizontal Beamwidth: 47 degrees @ ½ power Vertical Beamwidth: 55 degrees @ ½ power Antenna Material: Sealed in UV stable fiberglass enclosed radome Mounting Hardware: Stainless steel U bolts (included) for mounting up to 1 5/8 in. diameter pipe. Antenna Connector: N male reverse polarity with 18 in. pig tail Maximum Power Input: 50 Watts Antenna Envelope: 7 1/4 in. length by 2.0 in. diameter Windload (RWV): 120 mph Lateral Thrust at Rated Wind: 12.2 lbs. Wind Surface Area: 0.146 ft2 Bending Moment at Base Rated Wind: 3.6 lb-ft. Weight: .48 lbs. Only pre-made coax cables from the factory used in conjunction with either the AA20E omni-directional and AA203ES or AA204ES directional antennas meet all FCC Section 15.247(b) EIRP maximum power requirements. See Chapter 8 for details on maximum cable lengths. Model AA203ES Caution To comply with the FCC exposure compliance requirements, a separation distance of at least 100cm must be maintained between the antenna and all persons.
APPENDIX B SPECIFICATIONS Antenna Specifications Revised: 2 Jul 08 APX B-9 EST P/N AA107G Model No: AA204ES Applications: Fixed base mounting Antenna Type: 2.4 GHz ISM, Directional, 16 Element Yagi, DC Grounded Frequency: 2400-2483.5 MHz Polarization: Vertical or Horizontal Impedance: 50 ohms Gain: 13.5 dBi (11.3 dBd nominal) VSWR: < 2.1, 1.5:1 nominal Front To Back Ratio: >20 dB Horizontal Beamwidth: 28 degrees @ ½ power Vertical Beamwidth: 30 degrees @ ½ power Antenna Material: Fiberglass enclosed Recommended Mounting Hardware: Heavy duty U bolts for mounting up to 1 5/8 in. pipe (included). Adjustable yagi mounting kit for mounting up to 1 ½ in. pipe optional Antenna Connector: N male reverse polarity Cable Length: 18 in. Maximum Power Input: 50 Watts Wind Survival: 120 mph Antenna Envelope: 18 in. length by 3 in. width Equiv. Flat Plate Area: 0.375 ft² Lateral Thrust at Rated Wind: 31.4 lbs. Bendling Moment at Base Rated Wind: 23.6 lb-ft. Weight: .76 lbs. Only pre-made coax cables from the factory used in conjunction with either the AA20E omni-directional and AA203ES or AA204ES directional antennas meet all FCC Section 15.247(b) EIRP maximum power requirements. See Chapter 8 for details on maximum cable lengths. Use of the AA204ES, directional antenna is limited to fixed point to point applications only. In accordance FCC Section 15.247(b)iii, the operator or installer is responsible for ensuring the systems is used exclusively for fixed, point-to-point applications. Model 204ES Caution To comply with the FCC exposure compliance requirements, a separation distance of at least 100cm must be maintained between the antenna and all persons.

Navigation menu