Electronic Systems Technology ESTEEM195EG-1 ESTEEM 195Eg User Manual 195Eg Apx B Specifications

Download:
Mirror Download [FCC.gov]
Document ID	977687
Application ID	OGhtaVzXtIaJaelHM2PGXA==
Document Description	user manual apxB
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	30.2kB (377536 bits)
Date Submitted	2008-07-29 00:00:00
Date Available	2008-08-01 00:00:00
Creation Date	2008-07-23 10:44:59
Producing Software	GPL Ghostscript 8.54
Document Lastmod	2008-07-23 10:44:59
Document Title	195Eg Apx B - Specifications
Document Creator	PDFCreator Version 0.9.3
Document Author:	Dan Tolley

APPENDIX B
SPECIFICATIONS
Model 195Eg Specifications
LED Indicators
Power On/Off
Carrier Detect On/Off
Link Status On/Off
Receiver On/Off
Transmitter On/Off
I/O Connectors
Ethernet 10/100Base T
RS-232C Programming/Data Port
RJ-45
RJ-45
Dual Antenna input/Outputs
Remote Input Power
Direct Input Power
TNC Reverse Female
Power Over Ethernet Cable
Optional, Header Screw Connector
Transmiter
Frequency of Operation
RF Data Rates
2.412 to 2.462 GHz
Software Selectable in 11 Channels
1,2,5.5,6,9,11,12,18,24,36,48, & 54 Mbps Fixed or Auto Scaling
Tx Peak Output Power
1 Watt
RF Output Impedance
50 ohms
Receiver
Rx Sensitivity
-68 dBm @54 Mbps to –89 dBm @ 1 Mbps
Frame Error Rate <10%
Power
Power over Ethernet
Power Connector on Unit
Receive
Transmit
Case
Dimensions
IEEE 802.3af Standard Power Supply,
48 VDC @ 13 Watts
10 to 16 VDC
320 ma @ 12 VDC
1000 ma @ 12 VDC
1.9 in. H x 6.7 in. W x 6.2 in. L
Weight
Outdoor Pole Mounting Kit
Other
1.25 lbs.
Optional, EST P/N 195PM
Warranty
1 Year
Temperature Range
-30° to +60° C
Humidity
95% Non-condensing
FCC Type Acceptance
ENPESTEEM195EG-1
Industry Canada Type Acceptance
1457A-195EG
The GPL source code contained in this product is available as a free download from the following:
ftp://ftp.esteem.com/opensource/gplsourcepackage.tar.bz2
If you would like a copy of the GPL source code contained in this product shipped to you on CD,
please send $9.99 to 415 N. Quay Street, Kennewick, WA 99336 which covers the cost of preparing
and mailing a CD to you.
Specifications Subject to Change Without Notice
Revised: 2 Jul 08
APX B-1
EST P/N AA107G
APPENDIX B
SPECIFICATIONS
Model 195Eg Case Specifications
Revised: 2 Jul 08
APX B-2
EST P/N AA107G
APPENDIX B
SPECIFICATIONS
Antenna Specifications
Model No:
Antenna Type:
Applications:
Frequency:
Polarization:
Impedance:
Gain:
VSWR:
Front to Back Ratio:
Horizontal Beamwidth:
Vertical Beamwidth:
Antenna Material:
Mounting Hardware:
Antenna Connector:
Antenna Envelope:
Weight:
AA01S
Omni-Directional, variable angle rubber duck
Direct mount
2400 to 2485 MHz
Vertical
Caution
50 ohms
Omni-directional antenna
Unity
should not be located within
< 1.5
20 cm of personnel.
n/a
n/a
n/a
Rubber duct whip.
n/a
TNC-R Male
4.25 in. length by 1.75 in width
.08 lbs.
Model: AA20DMEg
Applications: Model 195Eg direct case mount
Antenna Type: Omni-Directional, Sleeve dipole
Frequency: 2400 to 2485 MHz
Polarization: Vertical
Impedance: 50 ohms
Gain: 5 dBi (3 dBd)
VSWR: < 2:1
Power: 10 W
Front To Back Ratio: n/a
Horizontal Beamwidth: n/a
Vertical Beamwidth: n/a
Antenna Material: Polyurethane Plastic Radome
Recommended Mounting Hardware: n/a
Antenna Connector: TNC-R Male
Flexibility: +/- 20 °
Antenna Envelope: 8.28 in. length by .54 in. width
Temperature: -40 to +70 C°
Weight: 33 grams
Revised: 2 Jul 08
Model AA01S
Caution
Omni-directional antenna
should not be located within
20 cm of personnel.
Model AA20DMEg
APX B-3
EST P/N AA107G
APPENDIX B
SPECIFICATIONS
Antenna Specifications
Model No:
Antenna Type:
Applications:
Frequency:
Polarization:
Impedance:
Gain:
VSWR:
Front to Back Ratio:
Horizontal Beamwidth:
Vertical Beamwidth:
Antenna Material:
Mounting Hardware:
Antenna Connector:
Antenna Envelope:
Weight:
AA20Eg
Omni Directional, DC Grounded
Fixed base
2400 to 2500 MHz
Vertical
50 ohms
6 dBi (4dBd)
1.2:1 Typical
n/a
n/a
40 degrees @ ½ power
Brass radiator, UV inhibited
fiberglass enclosed
Base to Mast, Supplied.
TNC-R Male with 36in. pig-tail.
12 in. length by 1 in. diameter
1.5 lbs.
Caution
To comply with the FCC
exposure compliance
requirements, a separation
distance of at least 20 cm
must be maintained between
the antenna and all persons.
Mounting Bracket
Model AA20Eg
Revised: 2 Jul 08
APX B-4
EST P/N AA107G
APPENDIX B
SPECIFICATIONS
Antenna Specifications
Model No:
Antenna Type:
Applications:
Frequency:
Polarization:
Impedance:
Gain:
VSWR:
Front to Back Ratio:
Horizontal Beamwidth:
Vertical Beamwidth:
Antenna Material:
Mounting Hardware:
Antenna Connector:
Maximum Power Input:
Antenna Envelope:
Windload (RWV):
Lateral Thrust at
Rated Wind:
Wind Surface Area:
Weight:
Revised: 2 Jul 08
AA203Eg
Directional, DC grounded
Fixed base.
2400 to 2485 MHz
Vertical or Horizontal
50 ohms
6 dBi (4 dBd)
< 1.5
>23 dB
55 degrees @ ½ power
55 degrees @ ½ power
Sealed in UV stable fiberglass enclosed radome
Stainless steel U bolts (included) for mounting up
to 1 5/8 in. diameter pipe.
TNC-R Male with 36in. pig tail
5 Watts
4.5 in. length by 3 in. diameter
125 mph
5.8 lbs.
0.060 ft2
1 lbs.
Caution
To comply with the FCC
exposure compliance
requirements, a separation
distance of at least 20 cm
must be maintained between
the antenna and all persons.
Model AA203Eg
APX B-5
EST P/N AA107G
APPENDIX B
SPECIFICATIONS
Antenna Specifications
Model No:
Applications:
Antenna Type:
Frequency:
Polarization:
Impedance:
Gain:
VSWR:
Front to Back Ratio:
Horizontal Beamwidth:
Vertical Beamwidth:
Antenna Material:
Recommended Mounting
Hardware:
Antenna Connector:
Maximum Power Input:
Wind Survival:
Wind Load:
Antenna Envelope:
Weight:
AA204Eg
Fixed base mounting
2.4 GHz ISM, Directional, DC Grounded, Parabolic Grid
2400-2485 MHz
Vertical or Horizontal
Caution
50 ohms
To comply with the FCC exposure
19 dBi (17 dBd) nominal
compliance requirements, a
< 1.5:1 nominal
separation distance of at least 50 cm
must be maintained between the
>24 dB
antenna and all persons.
16 degrees @ ½ power
11 degrees @ ½ power
Zinc plated cold rolled steel with polyester power
coat finish
Standard U-bolt steel mast clamp complete with
mounting hardware. Designed for masts of up to
2.5 in. O.D.
TNC-R Male with 36 in. pig-tail
10 Watts
100 mph
16 mph
34 in. length by 17 in. width by 11 in. height
3 lbs.
Model AA204Eg
Use of the AA204Eg, directional antenna is limited to fixed point-to-point applications only. In accordance with FCC
Section 15.247(b)iii, this antenna must be professionally installed. The installer must ensure the system is used exclusively
for fixed, point-to-point applications and the ESTeem Model 195Eg is set for 0.25 Watts output power (Power Level =
Min).
Revised: 2 Jul 08
APX B-6
EST P/N AA107G
APPENDIX B
SPECIFICATIONS
Antenna Specifications
Caution
Model No:
Antenna Type:
Applications:
Frequency:
Polarization:
Impedance:
Gain:
VSWR:
Front To Back Ratio:
Horizontal Beamwidth:
Vertical Beamwidth:
Antenna Material:
Mounting Hardware:
Antenna Connector:
Antenna Envelope:
Weight:
To comply with the FCC
AA20E
exposure compliance
requirements, a separation
Omni Directional, DC Grounded
distance of at least 20 cm
Fixed base
must be maintained between
2400 to 2500 MHz
the antenna and all persons
Vertical
50 ohms
6 dBd
< 1.5
n/a
n/a
35 degrees @ ½ power
Copper alloy radiator, UV inhibited fiberglass enclosed
Aluminum bracket for mounting to 1 ¼ to 2 in. diameter mast
included.
Mounting
N female reverse polarity.
Bracket
20 in. length by 1.35 in. diameter
2 lbs.
Model AA20E
Only pre-made coax cables from the factory used in conjunction with either the AA20E omni-directional and AA203ES or
AA204ES directional antennas meet all FCC Section 15.247(b) EIRP maximum power requirements. See Chapter 8 for
details on maximum cable lengths.
Revised: 2 Jul 08
APX B-7
EST P/N AA107G
APPENDIX B
SPECIFICATIONS
Antenna Specifications
Model No:
Antenna Type:
Applications:
Frequency:
Polarization:
Impedance:
Gain:
VSWR:
Front To Back Ratio:
Horizontal Beamwidth:
Vertical Beamwidth:
Antenna Material:
Mounting Hardware:
Antenna Connector:
Maximum Power Input:
Antenna Envelope:
Windload (RWV):
Lateral Thrust at
Rated Wind:
Wind Surface Area:
Bending Moment at
Base Rated Wind:
Weight:
AA203ES
Directional, 6 element yagi, DC grounded
Fixed base.
2400 to 2483.5 MHz
Vertical or Horizonal
50 ohms
7 dBd
< 1.5
13.5 dB
47 degrees @ ½ power
55 degrees @ ½ power
Sealed in UV stable fiberglass enclosed radome
Stainless steel U bolts (included) for mounting up
to 1 5/8 in. diameter pipe.
N male reverse polarity with 18 in. pig tail
50 Watts
7 1/4 in. length by 2.0 in. diameter
120 mph
12.2 lbs.
0.146 ft2
Caution
To comply with the FCC
exposure compliance
requirements, a separation
distance of at least 100cm
must be maintained between
the antenna and all persons.
Model AA203ES
3.6 lb-ft.
.48 lbs.
Only pre-made coax cables from the factory used in conjunction with either the AA20E omni-directional and AA203ES or
AA204ES directional antennas meet all FCC Section 15.247(b) EIRP maximum power requirements. See Chapter 8 for
details on maximum cable lengths.
Revised: 2 Jul 08
APX B-8
EST P/N AA107G
APPENDIX B
SPECIFICATIONS
Antenna Specifications
Model No:
AA204ES
Applications:
Fixed base mounting
Antenna Type:
2.4 GHz ISM, Directional, 16 Element Yagi, DC Grounded
Frequency:
2400-2483.5 MHz
Caution
Polarization:
Vertical or Horizontal
To comply with the FCC exposure
Impedance:
50 ohms
compliance requirements, a
Gain:
13.5 dBi (11.3 dBd nominal)
separation distance of at least 100cm
VSWR:
< 2.1, 1.5:1 nominal
must be maintained between the
antenna and all persons.
Front To Back Ratio:
>20 dB
Horizontal Beamwidth:28 degrees @ ½ power
Vertical Beamwidth:
30 degrees @ ½ power
Antenna Material:
Fiberglass enclosed
Recommended Mounting
Hardware:
Heavy duty U bolts for mounting up to 1
5/8 in. pipe (included). Adjustable yagi
mounting kit for mounting up to 1 ½ in.
pipe optional
Antenna Connector:
N male reverse polarity
Cable Length:
18 in.
Maximum Power Input:
50 Watts
Wind Survival:
120 mph
Model 204ES
Antenna Envelope:
18 in. length by 3 in. width
Equiv. Flat Plate Area:
0.375 ft²
Lateral Thrust at Rated
Wind:
31.4 lbs.
Bendling Moment at
Base Rated Wind:
23.6 lb-ft.
Weight:
.76 lbs.
Only pre-made coax cables from the factory used in conjunction with either the AA20E omni-directional and AA203ES or
AA204ES directional antennas meet all FCC Section 15.247(b) EIRP maximum power requirements. See Chapter 8 for
details on maximum cable lengths.
Use of the AA204ES, directional antenna is limited to fixed point to point applications only. In accordance FCC Section
15.247(b)iii, the operator or installer is responsible for ensuring the systems is used exclusively for fixed, point-to-point
applications.
Revised: 2 Jul 08
APX B-9
EST P/N AA107G

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 9
Producer                        : GPL Ghostscript 8.54
Create Date                     : 2008:07:23 10:44:59-07:00
Modify Date                     : 2008:07:23 10:44:59
Title                           : 195Eg Apx B - Specifications
Creator                         : PDFCreator Version 0.9.3
Author                          : Dan Tolley
Subject                         : 

EXIF Metadata provided by EXIF.tools