EnGenius Technologies EDS1130 Intelligent IP-Camera User Manual 2 of 2

Download:
Mirror Download [FCC.gov]
Document ID	2395000
Application ID	ENK8ue5Y5+k22c+1Pnn1nA==
Document Description	Users Manual (2 of 2).pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	369.39kB (4617380 bits)
Date Submitted	2014-09-19 00:00:00
Date Available	2014-09-19 00:00:00
Creation Date	2014-09-18 09:14:31
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2014-09-18 09:15:23
Document Title	Users Manual (2 of 2).pdf
Document Creator	Adobe InDesign CS6 (Windows)

Chapter 6
Camera Connecting to
EnGenius Gateway/
Router
Smart Recording is an intelligent camera management technology that allows EnGenius users to manage cameras collectively
with ease. EnGenius bundles cameras with IoT gateway and Intelligent Router series that provides a single entrance for integrated
management. Traditionally, if you have multiple cameras installed you will need to go through the tedious configurations on each of
the camera. The benefits of Smart Recording are as follows:
Easy and Integrated Access
manage each camera
individually
unified management with
Smart Recording
Integrated Storage
Chapter6 | Camera Connecting to EnGenius Gateway/Router
120
Easy Remote Access over Internet
Traditionally, you cannot get access to your Camera over the Internet without some manual configuration known as Port Forwarding
because your camera is installed under a local network. Smart Recording technology takes care all the complicated setup and leave
you with ease of control. That is, you will be able to access any of the cameras in your home by providing their DDNS names on
EnViewer mobile app or web browser if you are using PC/Laptop.
manual
configuration
Chapter6 | Camera Connecting to EnGenius Gateway/Router
EnGenius Smart
Recording
121
Enable Gateway/Router Storage Function
The best thing about Smart Recording is that you can make use of the EnGenius Network Storage function. You should attach an
external USB storage device (portable hard-disk or USB flash drive) to your gateway/router. Enter the Username and Password of your
gateway/router and click Login.
If you have not yet enable Network Storage Samba Server on your gateway/router, choose USB Port → File Sharing. Skip this step if
Samba is already enabled. Then, Enable Samba Service and click on Apply to activate the function.
Chapter6 | Camera Connecting to EnGenius Gateway/Router
122
On your gateway’s/router’s Main Menu, Click EnViewer → IP Camera under Cloud Services to access the connected cameras.
Depending on the firmware version of the device, the page may be found on System → IP Camera under Device Management.
Note: Only EnGenius Cameras can be managed collectively by EnGenius Gateway/Router. For other vendor’s cameras, you still have
to configure them one by one manually.
You should be see all your cameras listed on the IP Camera Client Table. If not, click Refresh button to scan the network again.
Please be noted that only EnGenius Cameras will be listed on the table.
Connect: You can get access to the selected camera’s
User Interface Management page.
Add Profile: Add the selected camera to a profile
(please refer to next section for more detail on
Profile)
Chapter6 | Camera Connecting to EnGenius Gateway/Router
123
Camera Profile
A Profile is an entry that represents the added camera. You must add the camera to a profile so that the gateway/router has
the privilege to configure your camera and link them together.
Add Profile
This example shows 4 connecting cameras on the gateway/router. We have chosen to add two cameras (Lobby and Entrance)
for demonstration purpose.
Click on Add Profile button to add the chosen camera.
Chapter6 | Camera Connecting to EnGenius Gateway/Router
124
IP Camera Name: Lobby (use meaningful name for better identification)
Schedule Recording: Enable/Disable this type of recording
Motion Recording: Enable/Disable this type of recording
Folder Name: The name of the folder where the media files of this camera will be stored on the gateway/router storage.
Storage Size: put 0 if storage is unlimited.
Overwrite: Enable/Disable over-writing the old files when there’s no space for storing the new files
Click Apply when the profile settings is done.
Chapter6 | Camera Connecting to EnGenius Gateway/Router
125
The added cameras will be listed as shown below.
You can Edit or Delete profile by selecting the profile and click on the buttons below.
Edit: Select the camera profile and then click Edit button to make the changes.
Delete Selected: Select the camera profile and then click Delete Selected button to delete the profile.
Delete All: Click Delete All to delete all the profiles.
Chapter6 | Camera Connecting to EnGenius Gateway/Router
126
Fine Tune Camera Configuration set by the Gateway/Router
This section provides extra information on what actually happened to your camera’s setting after you added it to the Profile on
the gateway/router.
It is helpful for you to go through the automatically configured camera settings and make proper changes when necessary.
Click on Connect button to open the chosen camera’s login page.
Chapter6 | Camera Connecting to EnGenius Gateway/Router
127
Camera Storage Setting
Then go to Event Server → Network Storage section.
As you can see shown below, the camera storage is automatically configured for you. These settings enables your camera to store
media files on the external storage attached to your gateway/router. Each camera will be given different Path so that you can search
for the associated files easily.
In the previous example, we have named the camera profile as Entrance; therefore, the Path given to this camera is /sda1/IP_
Camera/Entrace. Please do not change the settings because it only works if the setting matches the connected gateway/router.
Chapter6 | Camera Connecting to EnGenius Gateway/Router
128
Camera Event/Alarm Setting
The gateway/router configured the camera with default Event Action Type: Record. You can make necessary changes if necessary. For
instance, you may want to change Record to Snapshot if static pictures are preferable in your application.
Chapter6 | Camera Connecting to EnGenius Gateway/Router
129
Camera Motion Detection Setting
In the previous section, the Entrance profile is configured with Motion Detection enabled. Therefore, the gateway/router
configured the camera with a full screen motion detection window. You may adjust the motion detection window if necessary.
Chapter6 | Camera Connecting to EnGenius Gateway/Router
130
Access the Media files on the Gateway/Router
Using web browser
Please refer to EnGenius Gateway/Router user’s manual for more detail on the EnShare Storage feature.
You can click on
to access the storage.
Choose Admin and click Start to access.
Chapter6 | Camera Connecting to EnGenius Gateway/Router
131
Choose the storage device to access the file.
In the previous example, the Entrance camera profile defines the path /sda1/IP_Camera/Entrance/
The media files will be stored as shown below.
Click the target file to check the video download or
right click to download the file from network storage.
Chapter6 | Camera Connecting to EnGenius Gateway/Router
132
Using Windows File Explorer
Once enabled Samba on the EnGenius gateway/router, you should find the device under Network in your File Explorer as shown.
Double click on ENGENIUS to get access to the storage space.
Upon security prompt, enter the gateway’s/router’s
username and password to continue.
You can access the media files located under \\ENGENIUS\sda1\IP_Camera\Entrance
Chapter6 | Camera Connecting to EnGenius Gateway/Router
133
Chapter 7
Camera Connecting
to Other Router
Normally, you do not need to make any changes to your router setting to be able to use the camera. However, in case if you
experience issues in connecting the camera, you should probably check for the following settings. UPnP, UPnP Traversal and Firewall.
UPnP and UPnP Traversal:
Universal Plug and Play (UPnP) allows the other device to detect the presence of the camera so that communication become
possible. Please ensure that your router supports UPnP Traversal and has it enabled. Most of the modern wireless router today
supports this feature. You should enable UPnP if you wish your camera to be recognized by the home router. If you can’t find the
related settings, they are most likely enabled by default. UPnP Traversal makes camera remote access over the Internet possible using
camera DDNS name.
Firewall:
By default, the firewall function of the router is not configured to filter out specific traffic. However, in case if you have trouble
accessing the camera view, it’s likely that the traffic has been blocked by the firewall on your router. You may want to double check
whether you have blocked the service ports. Check the camera setting System → Service Port. Make sure you do not block the
following ports: 80, 50000, 554, 50045, 9091 and 50075.
Chapter7 | Camera Connecting to Other Router
135
Chapter 8
EnViewer APP
EnViewer is an APP that runs on the mobile devices such as mobile phones or tablets. This application enables you to view
and control the camera and provides basic control on the camera at real time. You will be required to have a mobile device to go
through the features in this chapter.
Chapter8 | EnViewer APP
137
Install EnViewer
Download the EnViewer APP by scanning the QR code shown on the management page using your mobile phone. Both Android and
iOS version are supported, please scan the corresponding QR code to download and install the APP.
Also, you can search “EnViewer by EnGenius” in App Store (for iPhone and iPad) or Google Play (for Android-based phone and tablets)
for download.
Note:
You need to have your camera installed and configured in your home work to be able to use EnViewer.
You need to have your mobile device connected to the same gateway/router that your camera is connected with through Wi-Fi.
Start the EnViewer. You will be guided to
Wizard for the first time using this APP.
Welcome for using EnViewer.
Chapter8 | EnViewer APP
138
EnViewer Wizard
The Wizard will take you through the initial settings quickly. Press Next to proceed.
Chapter8 | EnViewer APP
There are two ways to add new camera to EnViewer: QR Code and AUTO SEARCH.
139
QR Code
EnViewer will turn your mobile device camera into QR code reader. When the QR code reader is on, please aim your mobile
device towards the QR code label inside the packaging as shown below. EnViewer will read QR code and identify your camera in a few
seconds. You can also load the QR code image file stored on your phone for identification by pressing Read from Photo Album button.
Chapter8 | EnViewer APP
140
Auto Search
Through Auto Search, EnViewer scans the local
network for cameras. Click Next to start searching.
Please wait while EnViewer
scans the network. In case if
none were found, you can press
Try Again to re-scan.
Chapter8 | EnViewer APP
Cameras connected to the home gateway/router will be displayed
on the list. Tick the one you want to add by pressing the button
in front of their names. Then, press Save to complete the add
process. If you did not find the camera you intend to add, you can
press Refresh to try again.
Now, you have added a new camera
to EnViewer. Please refer to the
following sections on how to use
EnViewer.
141
EnViewer Interface
Add new Camera / Router or
Enter Wizard Mode
Search existing camera
View the selected camera
Switch to router list
Live View list
Group View list
Play Back
Camera Setting
About
Connected
Disconnected
Chapter8 | EnViewer APP
142
There are two types of view: Live View and Group View.
Live View monitors a single selected camera.
Group View monitors multiple grouped cameras simultaneously.
Which type of view is best for your application?
+ If you only have one camera connected to your gateway/router, Live View is your best choice.
+ If you have multiple cameras connected to your router, Group View enables you to view multiple cameras at once if you grouped them.
+ You can still choose to use Live View if you have several cameras connected to your gateway/router.
Chapter8 | EnViewer APP
143
Live View
Tap on Live View on the panel.
You can switch between Router List and Camera
List by tapping on the tab on the sides shown.
To view the camera, please switch to Camera List.
On the list, please tap on the camera name that you would to like view.
Lobb..
Change to Camera List
Change to Router List
Chapter8 | EnViewer APP
You are now viewing at real time.
The control panel located at the bottom of the screen allows you to
perform basic operation on the camera.
144
Camera Control Panel
Click on Resolution to change the view resolution.
When turned on, you will be able to hear the sounds from the video.
When turned on, you will be able to speak to the phone, the voice
will be played through the camera. The sound can only be played if a
speaker is connected to the camera on audio out port.
Takes a snapshot at real time.
Tap on the icon to start recording the video at real time. Click on the
icon again to stop recording. A red-dot “ ” will appear on the screen
when recording.
Chapter8 | EnViewer APP
145
Adding new Camera
You should have added your camera through the Wizard when you start the EnViewer. You can add another camera simply
by calling the Wizard again. Tap on the “
configuration detail.
You can manually enter the camera
information or scan the camera QR code.
“ icon. On the Add menu, select Start Wizard. Please refer to EnViewer Wizard for
Scan the Camera QR code
Click Yes to confirm adding the camera.
Click on Add Cam
-Lobby
Chapter8 | EnViewer APP
146
Edit Camera
Tap on the “
“ icon of
the camera you would like to
modify.
Tap on Done to save the changes.
Remove Camera
Click on Edit to enter edit mode
Select the camera and click Delete.
Done
Chapter8 | EnViewer APP
Delete
Answer OK to confirm the
deletion
147
Why Adding Routers
If you are monitoring 2 sites at two different locations say, home and store, you will need one router at each site. That is, you
will have two routers. Under each router, you may have multiple cameras and it becomes difficult for you to manage many cameras
under different domains. Adding routers allows you to manage these cameras of different domains easily. In such scenario, you need
to add each router to EnViewer and let EnViewer to discover all the cameras under each router site. After adding routers, the cameras
will be grouped by its connecting router when you perform camera search and live view. You can also add cameras of different under
different router into the same group view.
Home
Kitchen
Store
Chapter8 | EnViewer APP
148
Adding new Router
You may manage multiple routers on your EnViewer. Also, each Router can have multiple cameras under it.
Tap on the “
” icon. On the
Add menu, select Router to
proceed.
Assign a router name; in this example, we call it demo.
On the settings page, enter router’s information as in the
example shown below.
demo
Router Name
admin
User Name
******
Password
Click Done when finished.
router.engeniusddns.com Router DDNS Name
Chapter8 | EnViewer APP
149
Edit Router
Tap on the “
“ icon of
the router you would like to
modify.
demo
admin
Tap on Done to save the changes.
******
router.engeniusddns.com
demo
Remove Router
Click on Edit to enter edit mode
Select the camera and click Delete.
Delete
Done
demo
demo
Answer OK to confirm the
deletion
Router
Router
Chapter8 | EnViewer APP
150
Group View
EnViewer supports Group View, which allows you to monitor multiple cameras at the same time.
MyGroup
Group View is useful when you have multiple cameras. You can monitor them
simultaneously and magnify the view by simply selecting one of them on the
screen. To use the group view, you need to add a new Group first. You can view
4 cameras on the screen on a single page. If you have more than 4 cameras, you
can swipe the screen left and right to flip the pages.
MyGroup
Chapter8 | EnViewer APP
MyGroup
151
Add new Group
Enter the group name and then click on “
” icon to add camera to this group.
Note: You may add cameras of different sites (routers) into the same group.
All the cameras will be shown on
the Camera list, tick the camera
name to add into the group and
click Done to add the camera.
Chapter8 | EnViewer APP
When all cameras are added
into the group click on Done
to finish.
MyGroup
152
Edit Group
Tap on the “
“ icon of the
group you would like to modify
the profile.
Edit View
MyGroup
Click Done to save the changes.
MyGroup
Remove Group
Click on Edit to enter edit
mode.
Select the camera and click
Remove.
Answer OK to confirm the deletion
Delete
Done
MyGroup
MyGroup
Group
Group
Chapter8 | EnViewer APP
153
Using Group view
Tap on the group name to view
its associated cameras.
MyGroup
Double-Tap on the camera to
magnify the view.
MyGroup
MyGroup
The camera control panel works the same as in Live View.
Please refer to the Camera Control Panel section for detail.
Chapter8 | EnViewer APP
154
Search Local Camera
Click on ”
“ to search existing camera if not found on the list.
The search process may take a while, please wait patiently.
Home
Kitchen
If you have several routers, your cameras will be
grouped under each router which they belong to.
Store
Chapter8 | EnViewer APP
155
Using Play Back
Choose the Storage you would like to search for playback files. It depends on where you store your media
files for schedule recording or alarm media files. Choose either one to proceed to next screen. Choose SD
Card if you have the files stored locally on the camera SD card or EnGenius Storage if applicable.
Note: Ensure that you have added a router to use playback from EnGenius Storage.
You will be guided to a camera list. Here, you need
to choose the camera that you want to retrieve the
playback files from.
Tap on the camera name to proceed to the next step.
Chapter8 | EnViewer APP
First, choose the Date and
Time for playback.
Then, choose the FILE TYPE
(Video Event, Video Schedule
or Snapshot) by tapping on
the icon.
EnViewer will start searching
for the associated media files
that fall within the time range.
156
Settings
Tap on Settings and then choose the camera you would like to configure.
On the Settings Menu, choose the item you would like to configure. The supported settings
types are: General ,Recording ,Notification.
Audio
Recording
Under Audio Settings, you may turn ON or OFF:
Under Recording Settings, you may turn ON or OFF:
Audio Microphone
Audio Speaker
Recording by Event : Motion Detection / Audio Detection
Recording by Schedule
The settings will be applied automatically to your camera.
The settings will be applied automatically to your camera.
Chapter8 | EnViewer APP
157
Notification
Notification is a feature that sends message to your mobile devices when your camera detected predefined events (alarms). You can
register your mobile device by entering a name and turn set Push Message “ON”. EnViewer will registered your device immediately.
Note1: Alarm message will be sent to your mobile device ONLY if you have configured your
camera with at least one of the event types: motion detection or audio detection.
Note2: A mobile device can only register itself to the service. That is, if you need both your tablet
and mobile phone be notified about the alarms, each device must have EnViewer installed and
registered for notification individually. As long as your EnViewer AP is running the alarm messages
can be received even if the devices operate in idle mode.
On your camera setting User Management → Push Message
Mobile List, you can find out what device has been registered.
Chapter8 | EnViewer APP
158
The alarm message may appear differently on various platforms. The following example shows the alarm message on an iphone.
The messages appeared on top of the screen. Since the events may occur in series; therefore, it is normal that you got several
messages for a single event.
By sliding down the message row on the top, the details will appear
similar to the following.
Tap on one of them to open the message.
Note: The Device Name shown could be changed on Chapter 5Network - UPnP.
Upon receiving the alarm, you can choose to view the camera in Live
or Playback the recorded media files.
Note: You need to keep EnViewer stay in the device memory so that
alarm can be received by your phone upon event occurrence. The
alarm message below shows an example of an alarm event.
Chapter8 | EnViewer APP
159
About
The About page provide some helpful hints about EnViewer.
Check out the FAQs for some common questions.
Chapter8 | EnViewer APP
160
Chapter 9
Application Guide
This chapter demonstrates some common applications using EnGenius Camera. The examples assume that the camera is
already connected to a gateway/router that has Internet accessibility.
Gateway/Router
Wireless S
WAN
etup
Ethernet
Modem
Wired Set
up
Note: Please ensure that your gateway/router supports UPnP Traversal and has it enabled. Most of the modern wireless
gateway/router today supports this feature. If you can’t find the related settings, they are most likely enabled by default. UPnP
Traversal makes camera remote access over the Internet possible using camera DDNS name (ooooooo.engeniusddns.com).
Chapter9 | Application Guide
162
Example1 : Baby Monitoring
The application concept diagram shows a camera monitoring the baby room. The parents can locally and remotely view the
camera in real time. Please follow the instructions below for detail setup. The camera is configured with video detection on so
that the mother can be alarmed when the baby cries.
Home
at Work
baby room
192.168.0.100
OOOOOO.engeniusddns.com
router
192.168.0.1
office
real time monitoring locally and remotely
Chapter9 | Application Guide
living room
163
Step 1: Disable Schedule Recording
Please Disable Schedule Recording so that Event Recording can be configured.
Chapter9 | Application Guide
164
Step 2: Configure Event/Alarm
Event Management → Event/Alarm set event and alarm settings to Enable and click Apply.
Chapter9 | Application Guide
165
Step 3: Configure Audio Detection
Event Management → Audio Detection enable auto detection. Make changes to the settings and click Apply.
Step 4: Setting EnViewer Notification
Set Push Message ON and enter the device name.
Chapter9 | Application Guide
166
Example 2: Remote Surveillance and Motion Detection
The application concept diagram shows a camera monitoring the living room and entrance of their home. The couple wants
to remotely monitor their home and needs to be alarmed when motion (intrusion) or sound is detected.
on Vacation
Home
router
192.168.0.1
motion detection and audio detection
Chapter9 | Application Guide
192.168.0.100
OOOOOO.engeniusddns.com
167
Step 1: Disable Schedule Recording
Make sure that the Schedule Recording is DIsabled ahead so that the Event Recording can be configured.
Chapter9 | Application Guide
168
Step 2: Configure Motion Detection
Enable motion detection
Select Window 1 and adjust the Sensitivity to
higher percentage.
By default, the window 1 is set as full range as the detecting area. You may keep
the window as it is or resize it to focus on the objects that you intend to monitor.
Click on Apply to activate the setting.
Step 3: Configure Audio Detection
Event Management → Audio Detection enable auto detection. Make changes to the settings and click Apply.
Chapter9 | Application Guide
169
Step 4: Configure Event/Alarm
Event Management → Event/Alarm set event and alarm settings to Enable and click Apply.
Chapter9 | Application Guide
170
Step 5: Setting EnViewer Notification
Set Push Message ON and enter the device name.
Chapter9 | Application Guide
171
Example 3: Schedule Recording
A business owner can remotely monitor his store at home in live or playback the previously recorded video. The camera is
configured with schedule recording for working hours from 9 AM to 9 PM.
remote site
store
192.168.0.100
OOOOOO.engeniusddns.com
schedual recording duringwork hours for security
Chapter9 | Application Guide
router
192.168.0.1
172
Step 1: Disable Alarm
Disable Event/Alarm so that Schedule Recording can be configured.
Chapter9 | Application Guide
173
Step 2: Configure Schedule Recording
Go to Event Management → Schedule Recording
Set Status to Enable.
Select all the check boxes and set the week day Monday to Sunday.
Then, enter time range from 09:00 to 18:00.
Choose to save the recording to SD Card and confirm the Video Length for each file.
Click Apply to activate the settings.
Chapter9 | Application Guide
174
Step 3: Playback on EnViewer
Tap on Playback and then choose SD Card for playback files.
Set the date and time range.
Tap on Video Schedule for playback.
Chapter8 | EnViewer APP
175
Step 4: Playback on Web Browser
Login to the camera and enter main menu Storage → SD Card.
Choose video folder and drill down for the recorded media file you would like to playback.
Chapter8 | EnViewer APP
176
Chapter 10
Troubleshooting
Viewing Your Video
How do I view live streaming using a mobile?
You can view your video on your iPhone, iPad and Android-based phone and tablet by using EnViewer. EnViewer is an App that
allows you to view and manage your camera at real time.
Where can I download my app?
You can download it by or searching APP store (for iPhone and iPad) or Google Play(Android-based mobile devices) for
“EnViewer”. You can also scan the following QR code to download EnViewer directly.
Google Play
App Store
for Android™ Devices
for iPhone® and iPad®
How do I use the web viewer on a computer?
You can view the camera at real time using any of popularweb browser, e.g. Chrome, Internet Explorer, Firefox. Given that you
have configured your camera properly. You should be able to get access to your camera by entering its DDNS or IP address. If you have
trouble finding your camera on your home network. Please use the provided E on your CD, EnViewer Finder, to find out your camera’s
current IP address.
Chapter10 | Troubleshooting
178
Why is my live view goes grey?
You camera supports night-vision. When camera detects insufficient light, it will switch to night-vision mode for clearer image.
However, you can manually configure this feature under Media → Camera. Set the Day/Night mode to Auto, Day Mode (color) or
Night Mode (grey).
Why is my recorded video grey?
You camera supports night-vision. When camera detects insufficient light, it will switch to night-vision mode for clearer image.
Hence, the recorded video become grey.
Why is the camera having clicking sound?
Your camera supports night-vision. You may hear the clicking sound whenever the camera switches mode. However, you can
manually configure this feature under Media → Camera. Set the Day/Night mode to Auto, Day Mode (color) or Night Mode (grey).
Why is my image blur?
When object become out of focus the image may become blur. Please check your camera lens, make sure it is clean. Dust or
insects may block the view and cause the view become out of focus (blur).
Chapter10 | Troubleshooting
179
Networking
Why does my camera disconnect from my Wi-Fi?
There are various reasons that your camera disconnects from the wireless gateway/router. Usually it is due to weak of Wi-Fi
signals or interference from electrical appliances. Therefore, you should bring your camera closer to the gateway/router and verify
whether it’s caused by weak signal. You should check if gateway/router has just rebooted. The administrator has changed Wi-Fi
security settings. If your camera is located far from the gateway/router, the signal strength may be weak; however, there shouldn’t be
much problem in home settings unless there are many walls or metal obstacles that blocked the wireless signals. Lastly, reboot your
camera and router.
How can I minimize interference?
Make sure there is no electrical appliances near the camera, such as microwave or devices that may interfere with the camera.
Upon experiencing interference, try to turn off any possible electrical devices that are currently running.
Why my live view lags (latency)?
Since your camera image is transmitted over the network.
If you have wireless configuration for your camera, you may be experiencing wireless interference from other wireless devices
or home appliances. If disabling other wireless devices do not resolve the issue. Please use wired setup for your camera to ensure
stable video transmission.
Your network bandwidth determines the latency of your live view. If your network is loaded with P2P traffic; you may
experience some latency. Please avoid heavy traffic loading applications on the network.
It is normal that you experience latency if you are monitoring with your mobile device from a remote site. The 3G or 4G service
provider network bandwidth may vary from location to location.
Chapter10 | Troubleshooting
180
I have connected the camera to the home router, but how can I access the camera?
There are various ways to scan the network for you camera. If you are under a home network setting. The best way to get
access to your camera is by using the enclosed EnViewer Finder. Please refer to Chapter 3 for more detail.
Security and Privacy
Accessing the camera from the Internet is convenient; however, it is also possible for anyone who has your username and
password to login into your camera. Therefore, the utmost key is to keep your username and password safe and change them
regularly. Your videos or images are stored either locally or in network storage. The images and videos are accessible only when
provided with proper security check. Therefore, the media files should be safe.
Can EnGenius employees view my video?
No! No one can view your video or login into your camera without security check. The username and password is stored locally
in your camera and it is not accessible by anyone but yourself. Therefore, it is important for you to keep the security information
safely.
How do I let other family member to view the camera without giving away administrator account?
Your camera supports two types of users: Administrator and Viewer. The username and password you use to login to the
camera for initial setup is your administrator account. Therefore, you should create Viewer account for your family member so that
they can view the camera only. Please refer to User Management chapter for more detail on creating viewer account.
Chapter10 | Troubleshooting
181
Cloud Video Services
I can’t connect. What’s going on?
Check your router’s Internet setting. You can first check other devices connecting to the router has Internet connectivity and
determine whether the source of the issue. If other connecting devices can connect to the Internet through the router. Then the
problem may lies on other router setting. Check wireless security settings. Turn off any firewall rules on the router see if connection
gets through.
Chapter10 | Troubleshooting
182
Appendix
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Appendix | A
Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.
184
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been
applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:
•
EN60950-1
Safety of Information Technology Equipment
•
EN50385
Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human exposure to
electromagnetic fields (0 Hz - 300 GHz)
•
EN 300 328
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the
2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the
R&TTE Directive
•
EN 301 489-1
Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;
Part 1: Common technical requirements
•
EN 301 489-17
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;
Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment
Česky [Czech]
[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými
ustanoveními směrnice 1999/5/ES.
Dansk [Danish]
Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige
krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch [German]
Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den grundlegenden
Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Appendix | B
185
Eesti [Estonian]
Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust direktiivi
1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English
Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC.
Español [Spanish]
Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y
cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Ελληνική [Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Français [French]
Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE.
Italiano [Italian]
Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle altre
disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski [Latvian]
Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips] atbilst Direktīvas
1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių [Lithuanian]
Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos
nuostatas.
Nederlands [Dutch]
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentiële eisen en de
andere relevante bepalingen van richtlijn 1999/5/EG.
Malti [Maltese]
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti
oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar [Hungarian]
Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC
irányelv egyéb elõírásainak.
Polski [Polish]
Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostałymi
stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português [Portuguese]
[Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais e outras disposições
da Directiva 1999/5/CE.
Slovensko [Slovenian]
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive
1999/5/ES.
Slovensky [Slovak]
[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice
1999/5/ES.
Suomi [Finnish]
[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen laite on direktiivin
1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Svenska [Swedish]
Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Appendix | B
186

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2014:09:18 09:15:23+08:00
Create Date                     : 2014:09:18 09:14:31+08:00
Metadata Date                   : 2014:09:18 09:15:23+08:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Format                          : application/pdf
Document ID                     : uuid:abefbbec-09e9-4aa3-9e99-e59738e28931
Instance ID                     : uuid:9dc8a642-de81-485d-a562-4750944ff146
Producer                        : Adobe PDF Library 10.0.1
Page Count                      : 68
Creator                         : Adobe InDesign CS6 (Windows)

EXIF Metadata provided by EXIF.tools