EnGenius Technologies ENH1350EXT Outdoor Long Range Wireless Access Point User Manual
EnGenius Technologies Outdoor Long Range Wireless Access Point
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3906806 |
| Application ID | 3LeOy2Uwugew3Nu13gP4Sg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 409.95kB (5124402 bits) |
| Date Submitted | 2018-06-29 00:00:00 |
| Date Available | 2018-07-06 00:00:00 |
| Creation Date | 2018-06-28 10:57:58 |
| Producing Software | Adobe PDF Library 10.0.1 |
| Document Lastmod | 2018-06-28 17:58:24 |
| Document Title | User Manual |
| Document Creator | Adobe InDesign CS6 (Windows) |
Business Solutions User Manual ENH1350EXT ENH1750EXT version 1.1 Dual Band Long Range Wireless Outdoor Access Point/Base Station IMPORTANT To install this Access Point please refer to the Quick Installation Guide included in the product packaging. Table of Contents Chapter 1 Product Overview...................................................................... 4 ENH1750EXT Key Features/Introduction........................................................ 5 System Requirements............................................................... 6 Package Contents......................................................................... 7 ENH1350EXT Key Features/Introduction........................................................ 8 System Requirements............................................................... 9 Package Contents......................................................................... 9 Technical Specifications....................................................................10 Physical Interface..........................................................................14 Chapter 2 Before You Begin.................................................................... 16 Computer Settings............................................................................. 17 ENH1750EXT Hardware Installation.................................................................. 21 Mounting the AP.......................................................................... 22 ENH1350EXT Hardware Installation................................................................. 25 Mounting the AP...........................................................................26 Chapter 3 Configuring Your Access Point............................................28 Default Settings./Web Configuration.......................................... 29 Chapter 4 Building a Wireless Network............................................... 30 Access Point ........................................................................................ 31 Clien Bridge Mode............................................................................... 32 WDS AP Mode..................................................................................... 33 WDS Bridge Mode...............................................................................34 WDS Station Mode......................................................................,.. ...35 AP Mesh Mode.....................................................................................36 Mesh Only Mode.......................................................................... .....37 Chapter 5 Status..........................................................................................38 Overview..................................................................................... ..........39 Connection........................................................................................... 42 Chapter 6 Network ................................................................................... .44 Basic IP Settings..................................................................................45 Spanning Tree Protocol Setting....................................................46 Chapter 7 2.4 GHz/5 GHz Wireless.....................................................................47 Wireless Settings............................................................................... .48 2.4 GHz/5 GHz Wireless Network.................................................49 Wireless Security..................................................................................50 Wireless Traffic Shaping.................................................................. 53 Fast Roaming.........................................................................................54 Mesh Settings-ENH1750EXT........................................................ 55 Guest Network Settings.................................................................. 56 Wireless MAC Filteing.........................................................................58 Wireless Advanced.............................................................................. 59 Chapter 8 Management ............................................................................... 60 Management VLAN Settings......................................................... 61 Advanced Settings............................................................................. 62 CLI Settings/Email Alert....................................................................63 Time Zone..............................................................................................65 Auto Reboot Settings..................................................................... .66 Wi-Fi Scheduler....................................................................................67 Tools........................................................................................................ 68 Account/Firmware...............................................................................70 Backup/Restore ..................................................................................71 Log.............................................................................................................73 Logout/Reset.......................................................................................74 Appendix..............................................................................................................75 FCC Interference Statement...........................................................76 IC Interference Statement..............................................................77 CE Interference StatEment.............................................................79 Professional installation instruction...........................................80 Chapter 1 Product Overview Introduction Key Features-ENH1750EXT • Up to 29 dBm transmit power enabling long range connectivity • Supports IEEE802.11ac/a/b/g/n wireless standards with up to 450 Mbps data rate on 2.4GHz band and 1300Mbps on 5GHz band • Three detachable 5 dBi 2.4 GHz Omni-directional antennas • Three detachable 7 dBi 5 GHz Omni-directional antennas • Can be monitored after deployment with EnGenius EZ ControllerTM software for Windows (Free online download) • Mesh Supported • Can be used with included power adapter or via PoE with PoE 802.3at - capable switches or injectors • Dual Band/Three Stream • Band Steering shifts dual band clients to 5 GHz for better throughput performance • Secured Guest Network option available Introduction The ENH1750EXT is a high-powered, long-range 3x3 DualBand Wireless 802.11 ac/a/b/g/n Outdoor Access Point with speeds up to 450 Mbps on 2.4GHz and 1300Mbps on 5GHz band. It can be configure as an: Access Point, Client Bridge, or WDS (AP, Station & Bridge). The ENH1750EXT is designed to operate in a variety of outdoor environments. Its high-powered, long-range characteristics make it a cost- effective alternative to ordinary Access Points that don’t have the range and reach to connect to a growing number of wireless users who wish to connect to a business network. The ENH1750EXT supports the 2.4GHz frequency band under 802.11 b/g/n mode while at the same time providing 5GHz band under 802.11 ac/a/n mode for communicating Maximum data rates are based on IEEE 802.11 standards. Actual throughput and range may vary depending on many factors including environmental conditions, distance between devices, radio interference in the operating environment, and mix of devices in the network. Features and specifications subject to change without notice. Trademarks and registered trademarks are the property of their respective owners. For United States of America: Copyright © 2014 EnGenius Technologies, Inc. All rights reserved. to and from 5GHz capable computers, tablets or smart phones or transferring files. Several ENH1750EXTs can be deployed in a campus setting using the 5GHz band as a backhaul to provide multiple 2.4GHz wireless cells for computers or mobile devices in common outdoor areas. System Requirements The ENH1750EXT is easy to install in virtually any location with its included PoE (Power over Ethernet) injector for quick outdoor installation. The ENH1750EXT enables network administrators to control its transmit power and feature settings for selecting narrow bandwidth and traffic shaping. The ENH1750EXT also supports wireless encryption including Wi-Fi Protected Access (WPA-PSK/ WPA2-PSK) Encryption, and IEEE 802.1x with RADIUS. • Windows OS (XP, Vista, 7), Mac OS, or Linux-based operating systems The following are the Minimum System Requirements in order to configure the device. • Computer with an Ethernet interface or wireless network capability • Web-Browsing Application (i.e.: Internet Explorer, Firefox, Safari, or another similar browser application) Package Contents The ENH1750EXT package contains the following items:* • ENH1750EXT Access Point • 3 detachable 5 dBi 2.4 GHz Omni-directional Antenna • 3 detachable 7 dBi 5 GHz Omni-directional Antenna • Power Adapter (48V/0.8A) • PoE Injector (EPE-48GR) • Grounding Cable • Pole Mount Bracket • Wall Mount Base • Mounting Screw Set • Quick Installation Guide • Technical Support Card *(all items must be in package to issue a refund): Introduction Key Features-ENH1350EXT • Up to 28 dBm transmit power enabling long range connectivity • Supports IEEE802.11ac/a/b/g/n wireless standards with up to 450 Mbps data rate on 2.4GHz band and 1300Mbps on 5GHz band • Two detachable 5.17 dBi 2.4 GHz Omni-directional antennas • Two detachable 5.17 dBi 5 GHz Omni-directional antennas • Can be monitored after deployment with EnGenius EZ ControllerTM software for Windows (Free online download) • Can be used with included power adapter or via PoE with Proprietary 54V. • Fast Transition and Handover between Access Points • Band Steering shifts client devices to a proper frequency band for getting more bandwidth and speed under an Access Point. • Secured Guest Network option available Introduction ENH1350EXT equips with two powerful RF interfaces that support up to 867 Mbps in 5GHz frequency band and 400 Mbps in 2.4GHz frequency band (with 2ss/VHT40 clients). It can be configured as an: Access Point, Client Bridge, or WDS (AP, Station & Bridge). The ENH1350EXT is designed to withstand harsh environment conditions including serve and prolonged exposure to sunlight, extreme cold, frost, snow, rainfall, hail and humidity. The ENH1350EXT supports the 2.4GHz frequency band under 802.11 b/g/n mode while at the same time providing 5GHz band under 802.11 ac/a/n mode for communicating to and from 5GHz capable computers, tablets or smart phones or transferring files. Several ENH1350EXTs can be deployed in a campus setting using the 5GHz band as a backhaul to provide multiple 2.4GHz wireless cells for computers or mobile Maximum data rates are based on IEEE 802.11 standards. Actual throughput and range may vary depending on many factors including environmental conditions, distance between devices, radio interference in the operating environment, and mix of devices in the network. Features and specifications subject to change without notice. Trademarks and registered trademarks are the property of their respective owners. For United States of America: Copyright © 2014 EnGenius Technologies, Inc. All rights reserved. devices in common outdoor areas. The ENH1350EXT is easy to install in virtually any location with its included PoE (Power over Ethernet) adapter for quick outdoor installation. The ENH1350EXT enables network administrators to control its transmit power and feature settings for selecting narrow bandwidth and traffic shaping. The ENH1350EXT also supports wireless encryption including Wi-Fi Protected Access (WPA2-PSK) Encryption, and IEEE 802.1x with RADIUS. System Requirements Package Contents The following are the Minimum System Requirements in order to configure the device. The ENH1350EXT package contains the following items:* • Computer with an Ethernet interface or wireless network capability • 2 detachable 5 dBi 2.4 GHz Omni-directional Antenna • Windows OS(XP, Vista, 7, 8, 10), Mac OS, or Linux-based operating systems • 2 detachable 5 dBi 5 GHz Omni-directional Antenna • ENH1350EXT Access Point • PoE Adapter (54V/0.6A) • Web-Browsing Application (i.e.: Internet Explorer, Firefox, Safari, or • Power Cord another similar browser application) • Pole Mount Strap • Wall Mount Screw set • Quick Installation Guide *(all items must be in package to issue a refund) Technical Specifications ENH1750EXT Standard: IEEE802.11ac/a/n on 5 GHz IEEE802.11b/g/n on 2.4 GHz IEEE802.3at WDS Detail WDS AP WDS Bridge WDS Station Antenna 6 External N-type Antenna 3 x detachable 5 dBi 2.4 GHz Omni-directional Antennas 3 x detachable 7 dBi 5 GHz Omni-directional Antennas Mesh Detail Mesh AP Mesh Only Management Auto Channel Selection Multiple SSID: 16 SSIDs, 8 SSIDs per Radio BSSID SNMP V1/V2c/V3 MIB I/II, Private MIB VLAN Tag/VLAN Pass-through Clients Statistics Save Configuration as User Default Fast Roaming E-Mail Alert RADIUS Accounting Guest Network Physical Interface 2 x 10/100/1000 Gigabit Ethernet Port with PoE support LAN1 Port: IEEE802.3at PoE Input LAN2 Port: IEEE802.3af PoE Output Both Ethernet Ports support Surge Protection to 6KV LED Indicator Power LAN 1 LAN 2 2.4 GHz 5 GHz Power Requirements External Power Adapter, DC IN, 48V/0.8A IEEE802.3at support Control CLI Supported Distance Control (Ack Timeout) 802.1X Supplicant (CB Mode) Multicast Supported Auto Reboot Obey Regulatory Power Operation Modes Access Point WDS Mesh 10 Security WEP Encryption - 64/128/152 bit WPA/WPA2 Personal (WPA-PSK using TKIP or AES) WPA/WPA2 Enterprise (WPA-PSK using TKIP or AES) Hides SSID in beacons MAC address filtering, up to 50 MACs Wireless STA (Client) connection list Https Support SSH Support QoS (Quality of Service) Complaint with IEEE 802.11e standard Physical/Environment Conditions Operating: Temperature: -4 °F to 158 °F (-20 °C to 70 °C) Humidity (non-condensing): 90% or less Storage: Temperature: -22 °F to 176 °F (-30 °C to 80 °C) Humidity (non-condensing): 90% or less 11 ENH1350EXT Management Auto Channel Selection Multiple SSID: 8 SSIDs per Radio BSSID SNMP V1/V2c/V3 MIB I/II, Private MIB VLAN Tag/VLAN Pass-through Clients Statistics Save Configuration as User Default Fast Roaming E-Mail Alert RADIUS Accounting Guest Network Standard: IEEE802.11ac/a/n on 5 GHz IEEE802.11b/g/n on 2.4 GHz IEEE802.3at Antenna 4 External N-type Antenna 2 x detachable 5.17 dBi 2.4 GHz Omni-directional Antennas 2 x detachable 5.17 dBi 5 GHz Omni-directional Antennas Physical Interface 1 x 10/100/1000 Gigabit Ethernet Port with PoE support LAN Port: IEEE802.3af and Proprietary 54V POE input. Ethernet Ports support Surge Protection to 1KV Control CLI Supported Distance Control (Ack Timeout) 802.1X Supplicant (CB Mode) Multicast Supported Auto Reboot Obey Regulatory Power LED Indicator Power LAN 2.4 GHz 5 GHz Power Requirements External Power Adapter, DC IN, 48V/0.6A Security WPA2 Personal WPA2 Enterprise Hides SSID in beacons MAC address filtering, up to 32 MACs Wireless STA (Client) connection list Https Support SSH Support Operation Modes Access Point Client Bridge WDS WDS Detail WDS AP WDS Bridge WDS Station 12 QoS (Quality of Service) Complaint with IEEE 802.11e standard Power Setting ENH1350EXT follow below power table to do power setting. Physical/Environment Conditions Operating: Temperature: -4 °F to 140 °F (-20 °C to 60 °C) Humidity (non-condensing): 0%~90% typical Storage: Temperature: -40 °F to 176 °F (-40 °C to 80 °C) Humidity (non-condensing): 0%~90% typical 2.4G BAND1 5G BAND1 13 5G BAND 4 Physical Interface(ENH1750EXT) Dimensions and Weights Length: 11.22” Width: 8.58” Depth: 2.1” Weight: 4.17 lbs 1 2.4 GHz Antennas: Detachable 5 dBi 2.4 GHz Omni-directional 2 5 GHz Antennas Detachable 7 dBi 5 GHz Omni-directional 3 LAN Port 1 (802.3at PoE Input): Ethernet port for RJ-45 cable. 4 LAN Port 2 (802.3af PSE Output): Ethernet port for RJ-45 cable. 5 LED Indicators: LED lights for Power, LAN Port 1, LAN Port 2, 2.4 GHz Connection and 5 GHz Connection. 6 Ground 7 Mounting Holes: Using the provided hardware, the ENH1750EXT can be attached to a wall or pole. 14 Physical Interface(ENH1350EXT) Dimensions and Weights Length: 6.83” Width: 4.38” Depth: 1.19” Weight: TBD 1 2.4 GHz Antennas: Detachable 5.17 dBi 2.4 GHz Omni-directional 2 5 GHz Antennas Detachable 5.17 dBi 5 GHz Omni-directional 3 LAN Port (802.3af and Proprietary 54V PoE Input): Ethernet port for RJ-45 cable. 4 LED Indicators: LED lights for Power, LAN Port, 2.4 GHz Connection and 5 GHz Connection. 5 Mounting Holes: Using the provided hardware, the ENH1350EXT can be attached to a wall or pole. 15 Chapter 2 Before You Begin 16 Computer Settings Windows XP/Windows 7/Windows 8/Windows 10 1b. Move your mouse to the lower right hot corner to display the Charms Bar and select the Control Panel in Windows 8 OS. In order to use the Access Point, you must first configure the TCP/IPv4 connection of your Windows OS computer system. 1a. Click the Start button and open the Control Panel Windows 8 1c. In Windows 10, click Start to select All APPs to enter the folder of Windows system for selecting Control Panel. Windows XP Windows 7 Windows 10 17 4. Select Internet Protocol Version 4 (TCP/IPv4) and then select Properties. 2a. In Windows XP, click Network Connections. 2b. In Windows 7/Windows 8/Windows 10, click View Network Status and Tasks in the Network and Internet section, then select Change adapter settings. 3. Right click on Local Area Connection and select Properties. 5. Select Use the following IP address and enter an IP address that is different from the Access Point and Subnet mask, then click OK. 18 Note: Ensure that the IP address and Subnet mask are on the same subnet as the device. For example: ENH220EXT IP address: 192.168.1.1 PC IP address: 192.168.1.2 – 192.168.1.255 PC Subnet mask: 255.255.255.0 19 Apple Mac OS X 4. In Configure IPv4, select Manually. 1. Go to System Preferences (Which can be opened in the Applications folder or selecting it in the Apple Menu). 5. Enter an IP address that is different from the Access Point and Subnet mask then press OK. 2. Select Network in the Internet & Network section. Note: Ensure that the IP address and Subnet mask are on the same subnet as the device. For example: ENH900EXT IP address: 192.168.1.1 PC IP address: 192.168.1.2 – 192.168.1.255 PC Subnet mask: 255.255.255.0 6. Click Apply when done. 3. Highlight Ethernet. 20 Hardware Installation ENH1750EXT 1. Connect one end of the Ethernet cable into the main LAN port (PoE) of the Access Point and the other end to the AP Ethernet port on the PoE injector. This diagram depicts the hardware configuration. 2. Connect the Power Adapter to the DC-IN port of the PoE injector and plug the other end in to an electrical outlet. 3. Connect the second Ethernet cable into the LAN port of the PoE injector and the other end to the Ethernet port on the computer. 4. Screw on the provided antennas to the device. Once both connections are secure, verify the following: PoE Injector/ PoE Swtich a) Ensure that the POWER light is on (it will be green). Ethernet b) Ensure that the 2.4 GHz/5 GHz WLAN light is on (it will be green for both 5 GHz and 2.4 GHz). PC Power Outlet c) Ensure that the LAN (Computer/ENH1750EXT Connection) light is on (it will be green). d) Once all three lights are on, proceed to set up the Access Point using the computer. 21 Note: The Access Point supports both IEEE 802.3at PoE (Power over Ethernet) or the included power injector. You may use either one as the power source. Do NOT use both at the same time. Mounting the ENH1750EXT Using the provided hardware, the ENH1750EXT can be attached to a wall or a pole. 1. Wall Mount Kit 260x180x7 (mm) 3. Pipe 63.5 (D) x 12.7 (mm) 2. Pole Mount Kit 140x112x33 (mm) 4. Tool 20(D) x 6 (mm) 22 5. Screws: 6.5(D) x 9.95 (mm) To attach the ENH1750EXT to a wall using wall mounting kit. 1. Mark the four locations of the mounting holes on the flat mounting surface. 3. Place the lock and flat washers on the four hex cap screws and drive the screws to attach the bracket to the back of the Access Point. 2. Drill a 37 mm deep 8 mm hole in the markings and hammer the bolts into the openings. 4. Tighten the flat washers to secure the bracket to the mounting surface. 3. 1. 2. 4. 23 To attach the ENH1750EXT to a pole using the provided pole mounting kit: 1. Place the lock and flat washers on the four hex cap screws and drive the screws to attach the bracket to the back of the Access Point. 3. Thread the open end of the Pole Strap through the two tabs on the Pole Mount Bracket . 4. Lock and tighten the Pole Strap to secure the Pole Mount Bracket to the pole. 2. Drive the four round head screws to attach the Pole Mount Bracket to the bracket. 1. Note: See diagram below for vertical and horizonal placements. 2. 3. horizontal placement horizontal placement 24 4. horizontal placement Hardware Installation ENH1350EXT 1. Connect one end of the Ethernet cable into the LAN port (PoE) of the AP/ Bridge and the other end to the PoE port on the PoE adapter. This diagram depicts the hardware configuration. 2. Connect the Power cord with the PoE Adapter and plug the other end into an electrical outlet. 3. Connect the second Ethernet cable into the LAN port of the PoE adapter and the other end to the Ethernet port on the computer. PoE Adapter Ethernet 4. Screw on the provided antennas to the top of this device. Power Outlet Note: The AP/Bridge should ONLY be powered via Ethernet cable connected to the included PoE Adapter. PC Note: The AP/Bridge should ONLY be powered via Ethernet cable connected to the included PoE Adapter. 25 Mounting the ENH1350EXT Using the provided hardware, the ENH1350EXT can be attached to a wall or a pole. The height should not exceed 2 meter. 1. Wall Mounting Kit 2. Pole Mounting Strap (Φ66*12.6 mm) (Anchors: Φ5.5*18 mm & Bolts: Φ8*25mm) Anchors Bolts 26 To attach the ENH1350EXT to a wall using wall mounting kit. To attach the ENH1350EXT to a pole using the provided pole mounting kit: A. Determine where the Access Point to be placed and stick the Adhesive label on the surface. A. Thread the open end of the Pole Strap through the two tabs on the Pole Mount Bracket. B. Use the appropriate drill bit to drill two 8.1mm diagram and 26mm depth holes on the markings of the label.C. Remove the label and screw the anchors unto the holes until they are flush with the wall. B.Lock and tighten Pole Strap to secure Pole Mount Bracket to the pole. D. Screw the included screws into the anchors. Place the Access Point against wall with the mounting screw heads. 27 Chapter 3 Configuring Your Access Point 28 Configuring Your Access Point 2. The default username and password are admin. Once you have entered the correct username and password, click the Login button to open the web-base configuration page. This section will show you how to configure the device using the web-based configuration interface. Default Settings Please use your Ethernet port or wireless network adapter to connect the Access Point. IP Address 192.168.1.1 Username / Password admin / admin Web Configuration 1. Open a web browser (Internet Explorer/Firefox/Safari/ Chrome) and enter the IP Address http://192.168.1.1 *The model name will be varied by different models. 3. If successful, you will be logged in and see the User Menu of this Access Point. Note: If you have changed the default LAN IP Address of the Access Point, ensure you enter the correct IP Address. 29 Chapter 4 Building a Wireless Network 30 Before starting to configure this Access Point, you may realize the used scenario under varied operating modes.The AP has the ability to operate in various modes. This chapter describes purpose of different operating modes and lists down the operating modes for outdoor Access Points. Access Point Mode In Access Point Mode, AP behaves likes a central connection for stations or clients that support IEEE 802.11ac/a/b/g/n networks. The stations and clients must be configured to use the same SSID (Service Set Identifier) and security password to associate with the AP. The AP supports up to eight SSIDs at the same time for secure access. AP Access Point Client 2.4 GHz Client 5 GHz Client Client Client Client 31 Client Bridge Mode The AP can be used as a centralized Outdoor Access Point with which other EnGenius Wireless N 2.4 or 5 GHz Outdoor Client Bridges can associate; leveraging the long-range capability of their internal high-gain directional antennas, resulting in a very cost-effective solution to expand a company network over a multiple building campus. ENH202 Client Bridge ENH202 Client Bridge AP Access Point Client Client 2.4 GHz 2.4 GHz Client Client Client 5 GHz 5 GHz ENH500 Client Bridge AP Client Bridge Switch Client Switch Internet Client Client Client 32 Client Client WDS AP Mode The AP also supports WDS AP mode. This operating mode allows wireless stations to connect with Access Point via using WDS technology. In this mode, configure the MAC addresses or SSIDs in both Access Points to enlarge the wireless area by enabling WDS Link settings. WDS supports up to four (4) AP MAC addresses and four (4) SSIDs at the same time. AP WDS AP- AP WDS AP- 5 GHz 5 GHz Client Computer Client Computer 2.4 GHz Client 2.4 GHz Client Client 33 Client WDS Bridge Mode In WDS Bridge Mode, the Accesss Point can wirelessly connect different LANs by configuring the MAC address and security settings of each Access Points. Use this operating mode when two wired LANs located a small distance apart want to communicate with each other. The best solution is to use the Access Point to wirelessly connect two wired LANs, as shown in the following diagram. WDS Bridge Mode can establish up to four (4) to eight (8) WDS links, creating a star-like network. Note: WDS Bridge Mode does not act as an Access Point. Access Points linked by WDS are using the same frequency channel. More Access Points connected together may lower throughput. This configuration can be susceptible to generate endless network loops in your network, so it is recommended to enable the Spanning Tree function to prevent this from happening. Client Computer AP WDS Bridge AP WDS Bridge- Client Computer Client Computer AP WDS Bridge- 34 WDS Station Mode WDS station (WDS STA) mode expands the WDS by receiving a wireless signal/service and sharing it through the Ethernet port. With WDS STA mode. Access Point WDS AP on both 5 GHz or 2.4 GHz Access Point WDS Station Access Point WDS Station Access Point WDS Station 35 AP Mesh Mode-ENH1750EXT Under the AP Mesh mode, the ENH1750EXT can be used as the central connection hub for station or clients that support IEEE 802.11 b/g/n network. Under this mode, the ENH1750EXT can be configured with the same Mesh SSID and security password in order to associate with other ENH1750EXTs, as well as connect with clients under the same SSID and encryption signatures. For example, you would use one band to connect Access Points in range with Mesh Client Computer Client Computer Client Computer Client Computer Client Computer Client Computer ENH1750EXT Access Point Client Computer Client Computer ENH1750EXT Access Point ENH1750EXT Access Point Client Computer Client Computer ENH1750EXT Access Point Client Computer Client Computer Client Computer ENH1750EXT Access Point ENH1750EXT Access Point 36 Mesh Only Mode-ENH1750EXT Under the Mesh-only mode, the ENH1750EXT can be configured with the same Mesh SSID and security password in order to associate with other Mesh enabled ENH1750EXTs, instead of connecting with clients. ENH1750EXT Access Point ENH1750EXT Access Point ENH1750EXT Access Point ENH1750EXT Access Point ENH1750EXT Access Point ENH1750EXT Access Point 37 Chapter 5 Status 38 Overview Save Changes Device Status This page lets you save and apply the settings shown under Unsaved changes list, or Revert the unsaved changes and revert to the previous settings that were in effect. Clicking the Device Status link under the Overview menu shows the status information about the current operating mode. • The Device Information section shows general system information such as Device Name, MAC Address, Current Time, Firmware Version, and Management VLAN ID Note: VLAN ID is only applicable in Access Point, WDS AP or WDS BR mode. • The Memory Information section shows usage of 39 memory such as Total Available, Free, Cached, Buffered and WDS AP modes. • The LAN Information section shows the Local Area Network settings such as the LAN IP Address, Subnet mask, Primary DNS Address, Secondary DNS Address, status of DHCP client, and status of Spanning Tree protocol (STP). • The Wireless LAN Information 2.4 GHz/5 GHz section shows wireless information such as Operating Mode, Frequency, and Channel. Since this Access Point supports multiple-SSIDs, information about each SSID, the ESSID, and security settings, are displayed • The Statistics section shows Mac information such as SSID, MAC address, RX and TX. Note: Profile Settings are only applicable in Access Point 40 • The Wireless Mesh Information - 2.4 GHz section shows wireless information such as Operation Mode, Wireless Mode, Channel Bandwidth, Frequency/ Channel, Mesh SSID and Mesh Security. 41 Connection Realtime 2.4 GHz/5 GHz Connection List Realtime The Realtime section contains the following options: Click the connection link under the Overview menu displays the connection list of clients associated to the ENH1750EXT’s 2.4 GHz/5 GHz, along with the MAC addresses and signal strength for each client. Clicking Refresh updates the client list. CPU Loading: 3 minutes CPU loading percentage information, it displays current loading, average loading and peak loading status. Left bar is loading percentage; button is time tracing. Interval is every 3 seconds Note: Only applicable in Access Point and WDS AP modes. 2.4 GHz/5 GHz WDS Link List Click the connection link under the Overview menu. This page displays the current status of the WDS link, including WDS Link ID, MAC Address, Link Status and RSSI. Note: Only applicable in WDS AP and WDS Bridge modes. 42 Traffic Loading: 2.4GHz and 5GHz and Ethernet port inbound and outbound traffic by current, average and peak time. Realtime Connection (Pkts): Overview on current active network connections. It displays UDP and TCP packets information and other connection status. UDP connections curve is in blue; TCP connection curve is in green; others curve is in red. Below of chart shows connections source and destination. The Mesh Link List Monitor the 2.4GHz Mesh Link List under the status menu. The page will display the current status of the Mesh Links under the Mesh AP mode and Mesh nodes under the Mesh Only mode. Note: Only Applicable in the Mesh AP and Mesh Only mode. 43 Chapter 6 Network 44 Basic IP Settings IPv4/IPv6 Settings IP Network Settings: Select whether the device IP address will use a static IP address specified in the IP address field or be obtained automatically when the device connects to a DHCP server. This page allows you to modify the device’s IP settings. IP Address: The IP address of this device. Subnet Mask: The IP Subnet mask of this device. Gateway: The Default Gateway of this device. Leave it blank if you are unsure of this setting. Primary/Secondary DNS: The primary/secondary DNS address for this device. Save: Click Save to confirm the changes. 45 Spanning Tree Protocol (STP) Settings Spanning Tree Status: Enables or disables the Spanning Tree function.Default is Disable. This page allows you to modify the Spanning Tree settings. Enabling the Spanning Tree protocol will prevent network loops in your LAN network. Hello Time: Specifies Bridge Hello Time in seconds. This value determines how often the device sends handshake packets to communicate information about the topology throughout the entire Bridged Local Area Network. Max Age: Specifies Bridge Max Age in seconds. If another bridge in the spanning tree does not send a hello packet for a long period of time, it is assumed to be inactive. Forward Delay: Specifies Bridge Forward Delay in seconds. Forwarding delay time is the time spent in each of the Listening and Learning states before the Forwarding state is entered. This delay is provided so that when a new bridge comes onto a busy network, it analyzes data traffic before participating in the network. Priority: Specifies the Priority Number. A smaller number has a greater priority than a larger number. Save: Click Save to confirm the changes. 46 Chapter 7 2.4 GHz & 5 GHz Wireless 47 Wireless Wireless Settings Force 5GHz: When band steering is configured to Force 5GHz mode, the AP will not dual band capable client devices to network to the 2.4GHz band only if the client devices are not currently associated on 2.4GHz radio in this AP. Prefer 5GHz: When band steering is configured to Prefer 5GHz mode, the AP will steer dual band capable client devices to 5GHz radio when the RSSI value of these client devices on 5GHz radio is more than set one. The allowed RSSI value for default setting is -75dBm. Device Name: Enter a name for the device. The name you type appears in SNMP management. This name is not the SSID and is not broadcast to other devices. Band Steering: Enable Band Steering to send 802.11n clients to the 5 GHz band, where 802.11b/g clients cannot go, and leave 802.11b/g clients in 2.4GHz to operate at their slower rates. Before implementing this feature, we suggest you to assure the both 2.4GHz and 5GHz SSID, as welll as security settings must be the same. EnGenius Band Steering supports following advanced settings, *Band Balance: When band steering is configured to Band Balance mode, the AP will steer dual band capable client devices to 5GHz when the RSSI value of these client devices on 5GHz radio is more than set one. To evenly allocate RF resource on the both 2.4GHz and 5GHz radios, users also can set the portion of client devices on 5GHz radio to assure smoothly connection. The default value of the 5GHz radio is 75%. Save: Click Save to confirm the changes 48 This page displays the current status of the Wireless settings of the AP. bands. Channel HT Mode: Scrow down this list to select bandwidth for operating under a frequency band. The default channel bandwidth is 20 MHz on 2.4GHz frequency radio and 40 MHz on 5GHz frequency radio. Considering the different applications, users can decide to implement a channel bandwidth to fulfill real applications. The larger the channel, the greater the transmission quality and speed. 2.4 GHz/5 GHz Wireless Network Transmit Power (Tx Power): Default Tx power is Auto to obey regulartory power of each country. Channel: Click Configuration button to open a new windows to configure channels for performing wireless service. Operation Mode: Scrow down this list to select operation modes for implementing on this radio. The default operation mode is Access Point on base stations and Access Points and is Client Bridge on Client Premise Equipements (CPE). Meanwhile, EnGenius outdoor devices also support WDS modes for peer to peer or peer to multi-peer connections. Wireless Mode: Scrow down this list to select wireless broadcasting standard on 2.4GHz and 5GHz frequency 49 Wireless Security Key Length: Select the desired option and ensure that wireless clients use the same setting. Your choices are 64, 128, and 152-bit password lengths. The Wireless Security section lets you configure the AP’s security modes Default Key: Select the Key you wish to be the default. Transmitted data is ALWAYS encrypted using the Default Key; the other Keys are for decryption only. You must enter a Key Value for the Default Key. Encryption Key Number: Enter the Key Value or values you wish to use. Only the Key selected as Default is required. The others are optional. Secuirty Mode: Including WEP, WPA2-PSK, WPA2. We strongly recommend you to use WPA2-PSK mode. * Setting of WEP mode: Auth Type: Select Open System or Shared Key. Input Type: ASCII: Regular Text (recommended) Hexadecimal Numbers (For advanced users) 50 * Setting of WPA2-PSK: Encryption: You may select AES, TKIP or Both (TKIP+AES) to be the encryption type you would like. Please ensure that your wireless clients use the same settings. Passphrase: Wireless clients must use the same Key to associate the device. If using ASCII format, the Key must be from 8 to 63 characters in length. If using HEX format, the Key must be 64 HEX characters in length. * Setting of WPA2-Enterprise (Pre-Shared Key): Encryption: Select the WPA2 Enterprise. Please ensure that your wireless clients use the same settings. Group Key Update Interval: Specifies how often, in seconds, the Group Key changes. The default value is 3600. Radius Server: Enter the IP address of the Radius server. Radius Port: Enter the port number used for connections to the Radius server. 51 Radius Secret: Enter the secret required to connect to the Radius server. Radius Accounting: Enable or disable accounting feature. Radius Accounting Server: Enter the IP address of the Radius accounting server. Radius Accounting Port Enter the port number used for connections to the Radius accounting server. Radius Accounting Secret: Enter the secret required to connect to the Radius accounting server. Interim Accounting Interval: Specifies how often, in seconds, the accounting data sends. Note: 802.11n does not allow WPA2-PSK TKIP security mode. The connection mode will automatically change from 802.11n to 802.11g. 52 Wireless Traffic Shaping Traffic shaping regulates the flow of packets leaving an interface to deliver improved Quality of Service. Enable Traffic Shaping: Check this option to enable Wireless Traffic Shaping. Download Limit: Specifies the wireless transmission speed used for downloading. Upload Limit: Specifies the wireless transmission speed used for uploading. Per User: Check this option to enable wireless traffic shaping per user function. This function allow users to limit the maximum download / upload bandwidth for each client devices on this SSID. Save: Click Save to confirm the changes. 53 Fast Roaming Enable the function to serve mobile client devices that roam from Access Point to Access Point. Some applications running on Client devices require fast re-association when they roam to a different Access Point Please enter the settings of the SSID and initialize the Security mode to WPA enterprise, as well as to set the Radius Server firstly. Users can enable the Fast Roaming and implement the advanced search. Enable Fast Roaming: Enable or disable fast roaming feature. Enable Advanced Search: Enable or disable advanced search feature. Please also set the same enterprise Encryption under the same SSID on other Access Points and enable the Fast Roaming. When the configuration is realized on different Access Point, the mobile client devices can run the voice service and require seamless roaming to prevent delay in conversation from Access Point to Access Point. 54 Mesh Settings- ENH1750EXT AES Passphrase: Enter the key values you wish to uses. Other Access Points must use the same key to establish a mesh link Mesh SSID: To create a mesh network, please enter the Mesh SSID of the Access Point that you wish to include in the Mesh. Security: Select None or WPA2-PSK AES from drop-down list. 55 Guest Network Settings Starting IP Address: The first IP Address in the range of the addresses by the DHCP server. Adding a guest network allows visitors to use the Internet without giving out your office or company wireless security key. You can add a guest network to each wireless network in the 2.4 GHzb/g/n and 5 GHza/n frequencies. Ending IP Address: The last IP Address in the range of addresses assigned by the DHCP server. SSID: Specified the SSID for the current profile.. Choices given are: Disabled, Deny MAC in the list, or Allow MAC in the list. Hidden SSID: Check this option to hide SSID from clients, If checked, this SSID will not appear in the AP detect. Client Isolation: Click the appropriate radio button to allow or prevent communication between client devices. IP address: The IP Address of this device. Subnet Mask: The IP Subnet mask of this device. 56 RSSI Threshold Enable : Enable the Fast Handover feature by ensuring that each client is served by at least one Access Point at any time. Access Points continuously monitor the connectivity quality of any client in their range and efficiently share this information with other Access Points in the vincinity of that client to coordinate which of them should serve the client best. RSSI: Enter the RSSI (Received Signal Strength Index) in order to determine the handover procedure which the current wireless link will terminate. RSSI is an indication of the power level being received by the antenna. Therefore, the higher the RSSI number, the stronger the signal. 57 Wireless MAC Filtering ACL (Access Control List) Mode: Determines whether network access is granted or denied to clients whose MAC addresses appear in the MAC address table on this page. Choices given are: Disabled, Deny MAC in the list, or Allow MAC in the list. Wireless MAC Filtering is used to allow or deny network access to wireless clients (computers, tablet PCs, NAS, smartphones, etc.) according to their MAC addresses. You can manually add a MAC address to restrict permission to access EAP1750H. The default setting is: Disable Wireless MAC Filter. MAC Address: Enter the MAC address of the wireless client you wish to configure for. Note: Only applicable in Access Point and WDS AP mode. Add: Click Add to add the MAC address to the MAC Address table. Delete: Deletes the selected entries. Save: Click Save to apply the changes. 58 Wireless Advanced This page allows you to configure advanced wireless settings for the EWS550AP/EWS510AP/EWS511AP. It is recommended that the default settings are used unless the user has experience with more advanced networking features. Data Rate: Select a data rate from the drop-down list. The data rate affects throughput of data in the EAP1750H. The lower the data rate, the lower the throughput, though transmission distance will be lowered as well. 2.4 GHz/5 GHz Wireless Advanced Transmit Power: Sets the power output of the wireless signal. RTS/CTS Threshold: Specifies the threshold package size for RTC/CTS. A smaller number causes RTS/CTS packets to be sent more often and in turn consumes more bandwidth. Distance: Specifies the distance between Access Points and clients. Longer distances may drop high-speed connections. Aggregation: Merges data packets into one packet. This option reduces the number of packets, but increases packet sizes. Save: Click Save to confirm the changes. 59 Chapter 8 Management 60 Management VLAN Settings Management VLAN: If your network includes VLANs, you can enable Management VLAN ID for packets passing through the Access Point with a tag. This page allows you to assign a VLAN tag to packets sent over the network. A VLAN is a group of computers on a network whose software has been configured so that they behave as if they were on a separate Local Area Network (LAN). Computers on VLAN do not have to be physically located next to one another on the LAN. Save: Click Save to confirm the changes or Cancel to cancel and return to previous settings. Note: If you reconfigure the Management VLAN ID, you may lose your connection to this AP. Verify that the DHCP server supports the reconfigured VLAN ID and then reconnect to this AP using the new IP address. Note: Only applicable in Access Point and WDS AP modes. 61 Advanced Settings SNMP Settings Location: Specifies the location of the device. This page allows you to assign the Contact Details, Location, Community Name, and Trap Settings for a Simple Network Management Protocol (SNMP). SNMP is a networking management protocol used to monitor network attached devices. SNMP allows messages (called protocol data units) to be sent to various parts of the network. Upon receiving these messages, SNMP compatible devices (called agents) returns the data stored in their Management Information Bases. Community Name (Read Only): Specifies the password for the SNMP community for read only access. Community Name (Read/Write): Specifies the password for the SNMP community with read/write access. Trap Destination Address: Specifies the IP address of the computer that will receive the SNMP traps. Trap Destination Community Name: Specifies the password for the SNMP trap community. SNMPv3: Enables or disables the SNMPv3 feature. User Name: Specifies the username for SNMPv3. Auth Protocol: Selects the authentication protocol type: MDS or SHA. Auth Key: Specifies the authentication key. Priv Protocol: Selects the privacy protocol type: DES. Priv Key: Specifies the privacy key for privacy. Engine ID: Specifies the engine ID for SNMPv3. SNMP Enable/Disable: Enables or disables the SNMP feature. Apply Save: Click Apply Save to apply the changes. Contact: Specifies the contact details of the device. 62 CLI Settings Email Alert You can use the Email Alert feature to send messages to the configured email address when particular system events occur. Note: Do NOT use your personal email address as it can unnecessarily expose your personal email login credentials. Use a separate email account made for this feature instead. CLI: The Command Line Interface (CLI) allows you to type commands instead of choosing them from a menu or selecting an icon. SSH: Enable Secure Shell (SSH) to make secure, encrypted connections in the network. Secure Shell is a network protocol that allows data to be exchanged using a secure channel between two network devices. HTTPS: Enable HTTPS to transfer and display web content securely. The Hypertext Transfer Protocol over SSL (Secure Socket Layer) is a TCP/IP protocol used by web servers to transfer and display web content securely. Status: Enable this function for further settings. From: Enter the email address to show the sender of the email. To: Enter the address to receive email alerts. Subject: Enter the text to appear in the email subject line. 63 Username: Enter the username for the email account that will be used to send emails. Password: Enter the password for the email account that will be used to send emails. SMTP Server: Enter the IP address or hostname of the outgoing SMTP server. Port: Enter the SMTP port number to use for outbound emails. 64 Time Zone Time Setting Enable Daylight Saving: Check whether daylight savings applies to your area. This page allows you to set the internal clock of the AP. Start: Select the day, month, and time when daylight savings time starts. Enable Daylight Saving: Select the day, month, and time when daylight savings times ends. Manually Set Date and Time: Manually specify the date and time. Synchorize with PC: Click this button to synchorize Date and time of this AP with the PC. Automatically Get Date and Time: Select Automatically Get Date and Time and check whether you wish to enter the IP address of an NTP server or use the default NTP server to have the internal clock set automatically. Time Zone: Choose a time zone to implement the service for this AP. 65 Auto Reboot Settings You can specify how often you wish to reboot the AP. Auto Reboot Setting: Enables or disables the Auto Reboot function. Timer: Select the day and enter the time you would like to reboot automatically. Save: Click Save to apply the changes. 66 Wi-Fi Scheduler drop-down list. The Wi-Fi Scheduler can be created for use in enforcing rules. For example, if you wish to restrict web access to Mon-Fri from 3pm to 8pm, you could create a schedule selecting Mon, Tue, Wed, Thu and Fri while entering a Start time of 3pm and End Time of 8pm to limit access to these times. Day(s): Place a checkmark in the boxes for the desired days or select the All Week radio button to select all seven days of the week. Duration: The Start Time is entered in two fields. The first box is for hours and the second box is for minutes. The End Time is entered in the same format as the Start time. Status: Enables or disables the Wi-Fi scheduler function. Wireless Radio: Select 2.4 GHz or 5 GHz from the dropdown list for the preferred band type. SSID Selection: Select a SSID from the drop-down list. Schedule Templates: Select a schedule template from the 67 Tools Ping Test Parameters Start Ping: Click Start Ping to begin pinging the target device (via IP). This page allows you to analyze the connection quality of the AP and trace the routing table to a target in the network. Traceroute Target: Enter the IP address or domain name you wish to trace. Start Traceroute: Click Start Traceroute to begin the trace route operation. Target IP: Enter the IP address you would like to search. Ping Packet Size: Enter the packet size of each ping. Number of Pings: Enter the number of times you wish to ping. 68 Speed Test Parameters / LED Control LED Control This page allows you to analyze the connection quality of the AP and trace the routing table to a target in the network. Control LED on/off for Power, LAN interface, or 2.4 GHz/5 GHz WLAN interface. Power: Enables or disables the Power LED indicator. LAN: Enables or disables the LAN LED indicator. WLAN-2.4 GHz: Enables or disables the WLAN-2.4 GHz LED indicator. WLAN-5 GHz: Enables or disables the WLAN-5 GHz LED indicator. Target IP / Domain Name: Enter an IP address or domain name you wish to impelement a speed test for realizing the variance on wireless speed. Device Discovery This page allows you to discover devices from network for Operation Mode, IP Address, System MAC Address and Firmware version. Time Period: Enter the time in seconds that you would like the test to implement for and in how many intervals. IPv4/IPv6 Port: This Access Points uses IPv4 5001 and IPv6 5002 port for the speed test. Start: Click start to implement speed test. 69 Account Firmware This page allows you to change the AP username and password. By default, the username is: admin and the password is: admin. The password can contain from 0 to 12 alphanumeric characters and is case sensitive. Firmware Upgrade This page allows you to upgrade the firmware of the AP. Account Settings To Perform the Firmware Upgrade: 1. Click the Choose File button and navigate the OS file system to the location of the upgrade file. Administrator Username: Enter a new username for logging in to the New Name entry box. 2. Select the upgrade file. The name of the file will appear in the Upgrade File field. Current Password: Enter the old password for logging in to the Old Password entry box. 3. Click the Upload button to commence the firmware upgrade. New Password: Enter the new password for logging in to the New Password entry box. Note: The device is unavailable during the Firmware upgrade process and must restart when the upgrade is completed. Any connections to or through the device will be lost. Verify Password: Re-enter the new password in the Confirm Password entry box for confirmation. Apply: Click Apply to apply the changes. 70 Backup/Restore Backup Setting: Click Export to save the current configured settings. This page allows you to save the current device configurations. When you save your configurations, you also can reload the saved configurations into the device through the Restore Saved Settings from a file section. If extreme problems occur, or if you have set the AP incorrectly, you can use the Reset button in the Revert to Factory Default Settings section to restore all the configurations of the AP to the original default settings. Restore New Setting: To restore settings that have been previously backed up, click Browse, select the file, and click Restore. Restore to Default: Click Reset button to restore the ENH1750EXT to its factory default settings. 71 User Setting Back Up Setting as Default: Click Backup to backup the user settings you would like to the device’s memory for the default settings. The function allows you to backup the current device configurations into the AP as the default value. If extreme problems occur, or if you have set the AP incorrectly, you can push the Reset button to revert all the configurations of the AP to the user default. Restore to User Default: Click Restore to restore user settings to the factory standard settings. Note1: After setting the current settings as the default, you should click the Restore to Default on the web interface for reverting the settings into the factory default instead of pushing the reset button. Note2: Please write down your account and password before saving. The user settings will now become the new default settings at the next successful login. 72 Log System Log Remote Log The AP automatically logs (records) events of possible interest are in its internal memory. To view the logged information, click the Log link under the System Manager menu. If there is not enough internal memory to log all events, older events are deleted from the log. When powered down or rebooted, the log will be cleared. This page allows you to setup the Remote Log functions for the AP. Remote Log: Enable/disable this function. Log Server IP Address: Enter the IP address of the log server. Apply: Click Apply to apply the changes. Status: Enable/Disable this function. Log type: You may choose one of log types to display logs in the following window. The default log types is All. 73 Logout Logout: Click Logout in Management menu to logout. Reset In some circumstances, it may be required to force the device to reboot. Click on Reset to reboot the AP Once you click reset button, you will see the options for reboot or restore this AP. Please confirm again to logout the system or not. Reboot the device: Click it to reboot this device. Restore to Factory Default: Click it to reset this device to factory default setting. Restore to User Default: Click it to reset this device to user default settings. For realizing the setting method, you may refer page 74 and page 75. 74 Appendix 75 Appendix A Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operation of this device is restricted to indoor use only. 76 Appendix B - IC Interference Statement Industry Canada statement This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-247 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Caution: (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to cochannel mobile satellite systems; (ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. (iii) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement: (i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. (iii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. 77 FOR MOBILE DEVICE USAGE Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. Pour l’utilisation de dispositifs mobiles) Déclaration d’exposition aux radiations: Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm de distance entre la source de rayonnement et votre corps. 78 Appendix C - CE Interference Statemen Europe – EU Declaration of Conformity This device complies with Directive 2014/53/EU issued by the Commission of the European Community. - Declaration of Conformity Please added certification standard in your user manual which depended on the test standards your device performed. or - If the DoC should be a simplified version, please take below as reference – Hereby, EnGenius Networks declares that the EWS550AP/EWS510AP/EWS511AP are in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: Importer: EnGenius Networks Europe B.V. Importer Address: ESP 240, 5633 AC Eindhoven, The Netherlands Manufacturer : EnGenius Networks. Inc. Manufacturer Address: No.500, Fusing 3rd Rd., Hwa-Ya Technology Park Kuei-Shan Dist., Taoyuan City, Taiwan (R.O.C.) CE DoC Link: https://www.engeniusnetworks.eu/ens500ext-ac-ens500-ac-enstation5-accedoc 79 Appendix D -Professional installation instruction 1. Installation personal This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. 2. Installation location The product shall be installed at a location where the radiating antenna can be kept 20cm from nearby person in normal operation condition to meet regulatory RF exposure requirement. 3. External antenna Use only the antennas which have been approved by the applicant. The non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC/IC limit and is prohibited. 4. Installation procedure Please refer to user’s manual for the detail. 5. Warning Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty. 80
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Create Date : 2018:06:28 10:57:58+08:00 Metadata Date : 2018:06:28 17:58:24+08:00 Modify Date : 2018:06:28 17:58:24+08:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:d042fc3d-c961-4c09-a0a1-d3ba9f25cdcb Original Document ID : xmp.did:C4416EC81C206811822AF00EF18081D8 Document ID : xmp.id:73CDF2D17E7AE8119A6A87EBAB51F704 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:06B7737D7E7AE8119B7699246F6D8BB1 Derived From Document ID : xmp.did:5407CF60565EE811987AD7EF0DD7BE8D Derived From Original Document ID: xmp.did:C4416EC81C206811822AF00EF18081D8 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2018:06:28 10:57:58+08:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 80 Creator : Adobe InDesign CS6 (Windows)EXIF Metadata provided by EXIF.tools