Enlighted SU5E SU-5E Micro Sensor User Manual PowerPoint Presentation
Enlighted, Inc. SU-5E Micro Sensor PowerPoint Presentation
User Manual
Connecting the Sensor Cable to the Control Unit Step 1: Connect the RJ12 end of the sensor cable to the Control Unit (CU). For wiring connections from the Control Unit to the sensor, refer to the Control Unit Installation Guide. Step 2: Energize the luminaire and confirm that the green LED is solid. LED Description FCC and Industry Canada Compliance Information This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with Part 15 of the FCC Rules and Industry Canada licenseexempt RSS standard(s). Operation is subject to the following two conditions: • this device may not cause harmful interference, AND • this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Enlighted Inc. could void the user's authority to operate the equipment. Micro Sensor (SU-5E) Installation Instructions Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: • l'appareil ne doit pas produire de brouillage, ET • l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Micro Sensor and Carrier CE LED Status Description/Solution LED not on Check power and wiring Green blinking Sensor commissioned and working Red blinking Sensor not commissioned Red solid Faulty sensor – replace sensor Green solid Sensor installed, initialized, and uncommissioned – waiting for discovery. Blue solid Sensor received a request to identify itself This device complies with the essential requirements and other relevant requirements of the R&TTE Directive (1999/5/EC). The equipment is Class 1 radio equipment which can be placed on the market and be put into service without restrictions in accordance with article 1(3) of Commission Decision 2000/299/EC (Version July 2014). Supplemental Components • Enlighted Sensor Cable • Enlighted Control Unit Technical Support For questions regarding the installation or operation of this product, contact Enlighted Technical Support: support@enlightedinc.com Tools you may Need • 7/8” Drill bit (1/2” knock out trade size) • Hand drill Company Contact Information Location: 930 Benecia Ave, Sunnyvale, CA 94085 Phone: +1.650.964.1094 Web: enlightedinc.com Model No. : SU-5E-01 FCC ID: AQQ-SU5E IC: 10138A-SU5E Shipped Components • Enlighted Micro Sensor Copyright © 2017 Enlighted Inc. All rights reserved. All other brand or product names are trademarks of their respective companies or organizations. R 005-101515 Page 5 Page 6 93-02056-01 Rev02 Page 1 Caution Step 6: Insert the 8-pin end of the sensor cable through the carrier. Fixture Mount Sensor Installation Step 7: Connect the 8-pin connector to the sensor. Installation and maintenance must be performed by a qualified electrician in accordance with local, state, and national electrical codes (NEC) and requirements. Step 4: Thread the plain end of the nut from behind the tile to secure the carrier. Step 1: De-energize the luminaire. Step 8: Guiding the wire from above, push the sensor into the carrier until it securely clicks into the carrier. Note: For fixture mounting, use the fixture carrier and nut that is shipped with the sensor. Fixture Carrier Step 9: Leave four inches of slack cable in the sequence loop to avoid pinching of the cable and to bring the sensor down if it needs to be replaced. Nut Step 2: Determine the location for the sensor in the fixture and cut a ½ inch (7/8” diameter) knockout in the fixture. If the tile is thicker than normal, flip the nut and thread the ribbed end of the nut to secure the carrier. Step 5: Insert the 8-pin end of the sensor cable through the carrier. Step 6: Connect the 8-pin connector to the sensor. Note: Do not pull the cable forcefully as this might damage the cable or connector. Step 10: See section Connecting the Sensor Cable to the Control Unit on Page 5. Tile Mount Sensor Installation Step 1: De-energize the luminaire. Note: For tile mounting, use the tile carrier and nut that is shipped with the sensor. Step 7: Guiding the wire from above, push the sensor into the carrier until it securely clicks into the carrier. Step 3: Insert the fixture carrier through the hole in the fixture. Tile Carrier Step 4: From behind the fixture, align the tabs of the nut with the keys on the fixture carrier. Nut Step 2: Make a 7/8th diameter hole in the ceiling tile. Step 3: Insert the tile carrier through the hole into the tile. Step 5: Slide the tabs of the nut along the keys of the carrier to fasten the carrier. Step 8: Leave four inches of slack cable in the sequence loop to avoid pinching of the cable and to bring the sensor down if it needs to be replaced. Note: Do not pull the cable forcefully as this might damage the cable or connector. Keys Tabs Page 2 Page 3 Step 9: See section Connecting the Sensor Cable to the Control Unit on Page 5. Page 4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Enlighted Create Date : 2017:05:02 09:39:26-07:00 Modify Date : 2017:05:02 09:39:40-07:00 Language : EN-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30 Metadata Date : 2017:05:02 09:39:40-07:00 Creator Tool : Acrobat PDFMaker 17 for PowerPoint Document ID : uuid:ad6c605e-7af0-4d2c-a7b1-2c4bf8e7d11b Instance ID : uuid:bc9eac31-76cf-4934-9b05-9691eee3bea4 Format : application/pdf Title : PowerPoint Presentation Creator : Enlighted Producer : Adobe PDF Library 15.0 Tag Template ID : TC038954999991 Page Layout : SinglePage Page Count : 2EXIF Metadata provided by EXIF.tools