Entrust 506241001 RFID Module User Manual Cover

Entrust Datacard Corporation RFID Module Cover

Contents

User Manual II

Datacard® SD™ Series Card PrintersUser’s GuideNovember 2013Part No. 527399-001 Rev. A-01
ii NoticePleasedonotattempttooperateorrepairthisequipmentwithoutadequatetraining.Anyuse,operation,orrepairyouperformthatisnotinaccordancewiththeinformationcontainedinthisdocumentationisatyourownrisk.Proprietary NoticeAlldrawingsandinformationhereinarethepropertyofDataCardCorporation.Allunauthorizeduseandreproductionisprohibited.Trademark AcknowledgmentsDatacardisaregisteredtrademarkandservicemarkofDataCardCorporationintheUnitedStatesandothercountries.SDisatrademarkofDataCardCorporation.WindowsisaregisteredtrademarkofMicrosoftCorporation.Allotherproductnamesarethepropertyoftheirrespectiveowners.DatacardGroup11111BrenRoadWestMinnetonka,MN55343‐9015Phone:952‐933‐1223Fax:952‐933‐7971www.datacard.com©2013DataCardCorporation.Allrightsreserved.PrintedintheUnitedStatesofAmerica.
iii Compliance Statements Liability StatementThe WARNING and CAUTION labels have been placed on the equipment for your safety. Please do not attempt to operate or repair this equipment without adequate training. Any use, operation or repair in contravention of this document is at your own risk. Safety All Datacard® products are built to strict safety specifications in accordance with CSA/UL60950-1 requirements and the Low Voltage Directive 2006/95/EC. Therefore, safety issues pertaining to operation and repair of Datacard® equipment are primarily environmental and human interface.The following basic safety tips are given to ensure safe installation, operation and maintenance of Datacard® equipment. • Connect equipment to a grounded power source. Do not defeat or bypass the ground lead. • Place the equipment on a stable surface (table) and ensure floors in the work area are dry and non-slip. • Know the location of equipment branch circuit interrupters or circuit breakers and how to turn them on and off in case of emergency. • Know the location of fire extinguishers and how to use them. ABC type extinguishers may be used on electrical fires. • Know local procedures for first aid and emergency assistance at the customer facility. • Use adequate lighting at the equipment location. • Maintain the recommended temperature and humidity range in the equipment area.
iv Regulatory ComplianceThese notices apply to the Datacard printer and all Datacard accessory devices that connect to the printer.FCC NoticesThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:— Reorient or relocate the receiving antenna.— Increase the separation between the equipment and receiver.— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.— Consult the dealer or an experienced radio/TV technician for help.Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.Industry Canada NoticeThis device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
v Host Device Labeling Requirement NoticeTo meet the FCC and Industry Canada host device labeling requirements, any host equipment incorporating the 506241 module must include the FCC ID/IC number on the host label as follows:Contains transmitter module IC: 889B-506241001where 889B-506241001 is the module's IC certification number.Contains transmitter module FCC ID: GDI-506241001where GDI-506241001 is the module's FCC ID number.Notice for Europe The EU Declaration of Conformity can be found on Datacard.comWe hereby certify that this printer complies with EMC Directive2004/108/EC , R&TTE Directive 1999/5/EC, and the EU RoHS Directive EU Directive 2011/65/EC. This printer conforms to Class A of EN 55022 and to EN 301 489-5. Operation of this equipment in a residential environment may possibly cause interference. In the event of interference, the users, at their own expense, will be required to take whatever measures are necessary to correct the problem.Notice for China (Simplified Chinese) 嬎⏲㬌ᷢ B 乏ṏ⑩炻⛐䓇㳣䍗⠫ᷕ炻宍ṏ⑩⎗傥Ể忈ㆸ㖈乧䓝⸚㈘ˤ⛐征䥵ね⅝ᶳ炻⎗傥暨天䓐㇟⮡⸚㈘慯⍾↯⭆⎗埴䘬㍒㕥ˤNotice for Taiwan (Traditional Chinese)

Navigation menu