Entrust 506241001 RFID Module User Manual Cover

Download:
Mirror Download [FCC.gov]
Document ID	2108926
Application ID	KIOR34YuZ3ycpfO1a99FwA==
Document Description	User Manual II
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	10.27kB (128325 bits)
Date Submitted	2013-11-01 00:00:00
Date Available	2014-04-30 00:00:00
Creation Date	2011-05-04 14:13:29
Producing Software	Acrobat Distiller 10.1.8 (Windows)
Document Lastmod	2013-10-31 13:28:00
Document Title	Cover
Document Creator	FrameMaker 10.0.2
Document Author:	M Helm

Datacard® SD™ Series Card Printers
User’s Guide
November 2013
Part No. 527399-001 Rev. A-01
Notice
Please do not attempt to operate or repair this equipment without adequate
training. Any use, operation, or repair you perform that is not in accordance with
the information contained in this documentation is at your own risk.
Proprietary Notice
All drawings and information herein are the property of DataCard Corporation. All
unauthorized use and reproduction is prohibited.
Trademark Acknowledgments
Datacard is a registered trademark and service mark of DataCard Corporation in
the United States and other countries.
SD is a trademark of DataCard Corporation.
Windows is a registered trademark of Microsoft Corporation.
All other product names are the property of their respective owners.
Datacard Group
11111 Bren Road West
Minnetonka, MN 55343‐9015
Phone: 952‐933‐1223
Fax: 952‐933‐7971
www.datacard.com
©2013 DataCard Corporation. All rights reserved.
Printed in the United States of America.
ii
Compliance Statements
Liability Statement
The WARNING and CAUTION labels have been placed on the equipment for your safety.
Please do not attempt to operate or repair this equipment without adequate training.
Any use, operation or repair in contravention of this document is at your own risk.
Safety
All Datacard® products are built to strict safety specifications in accordance with CSA/
UL60950-1 requirements and the Low Voltage Directive 2006/95/EC.
Therefore, safety issues pertaining to operation and repair of Datacard® equipment are
primarily environmental and human interface.
The following basic safety tips are given to ensure safe installation, operation and
maintenance of Datacard® equipment.
•
Connect equipment to a grounded power source. Do not defeat or bypass
the ground lead.
•
Place the equipment on a stable surface (table) and ensure floors in the work
area are dry and non-slip.
•
Know the location of equipment branch circuit interrupters or circuit
breakers and how to turn them on and off in case of emergency.
•
Know the location of fire extinguishers and how to use them. ABC type
extinguishers may be used on electrical fires.
•
Know local procedures for first aid and emergency assistance at the customer
facility.
•
Use adequate lighting at the equipment location.
•
Maintain the recommended temperature and humidity range in the
equipment area.
iii
Regulatory Compliance
These notices apply to the Datacard printer and all Datacard accessory devices that
connect to the printer.
FCC Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a commercial installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Industry Canada Notice
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
iv
Host Device Labeling Requirement Notice
To meet the FCC and Industry Canada host device labeling requirements, any host
equipment incorporating the 506241 module must include the FCC ID/IC number on the
host label as follows:
Contains transmitter module IC: 889B-506241001
where 889B-506241001 is the module's IC certification number.
Contains transmitter module FCC ID: GDI-506241001
where GDI-506241001 is the module's FCC ID number.
Notice for Europe
The EU Declaration of Conformity can be found on Datacard.com
We hereby certify that this printer complies with EMC Directive2004/108/EC , R&TTE
Directive 1999/5/EC, and the EU RoHS Directive EU Directive 2011/65/EC. This printer
conforms to Class A of EN 55022 and to EN 301 489-5. Operation of this equipment in a
residential environment may possibly cause interference. In the event of interference,
the users, at their own expense, will be required to take whatever measures are
necessary to correct the problem.
Notice for China (Simplified Chinese)
嬎⏲
㬌ᷢ B 乏ṏ⑩炻⛐䓇㳣䍗⠫ᷕ炻
宍ṏ⑩⎗傥Ể忈ㆸ㖈乧䓝⸚㈘ˤ
⛐征䥵ね⅝ᶳ炻⎗傥暨天䓐㇟
⮡⸚㈘慯⍾↯⭆⎗埴䘬㍒㕥ˤ
Notice for Taiwan (Traditional Chinese)

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : M Helm
Create Date                     : 2011:05:04 14:13:29Z
Modify Date                     : 2013:10:31 13:28:00-05:00
Has XFA                         : No
Language                        : en
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : FrameMaker 10.0.2
Metadata Date                   : 2013:10:31 13:28-05:00
Producer                        : Acrobat Distiller 10.1.8 (Windows)
Format                          : application/pdf
Title                           : Cover
Creator                         : M Helm
Job Ref                         : r02 - Added DocumentSubTitle tag
Document ID                     : uuid:a5468a4e-85a0-4a22-b5c8-00c0061a3cdf
Instance ID                     : uuid:7bcfc8a9-de86-4015-9085-9cfe7a6ccf7f
Page Mode                       : UseNone
Page Count                      : 5

EXIF Metadata provided by EXIF.tools