Terminal(FWT) User Quick Manual
How to enter commands
Hidden Menu
Ring / Sound Menu
Tools Menu
Time Menu
Setting Menu
Data Mode Menu
Phone Book
Sungil Telecom
( Model Name : SXT-800U )
This document and the information contained in it is CONFIDENTIAL INFORMATION
and shall not be used, or published, or disclosed, or disseminated outside Company in
whole or in part without Company consent. This document contains trade secrets of
Company. Reverse engineering of any or all of the information in this document is
prohibited..
SXT-800U User Quick Manual
2/15
Ⅰ. How to enter commands.
Pick up the handset on your pots.
Press Entry code : ‘##XX’ ( ‘XX’ is 2 digit code )
: Prefix code, “##”, makes a terminal ready to receive commands. A following two digits
are command.
Actually, Each commands are a sequence digits to get to a specific function like as a
following menu structure.
Ex)
‘01’ – SIO : You just choosed Menu ‘0’ and Submenu Menu ‘1’ linked to SIO.
‘02’ – Emergency : You just choosed Menu ‘0’ and Submenu Menu ‘2’ linked
Emergency menu.
Note : Whenever you set the values of a Emergency, a hotline, a mirroring, a new code, a
outgoing restrict, a reset phone, a voice privacy, A lockcode prompt sound which
requests you to enter a lock code will be heard immediately.
Ex) ##03 Æ lockcode prompt sound Æ lock code Æ you can set Emergency number
Note : a FWT will go to idle state automatically when a user choose wrongly a parameter
or a function in a menu linked a command..
Menu Structure
0. Hidden Menu
1. SIO
2. Emergency
3. HOT Line
4. Mirroring ( will be used it in a factory )
5. A Key
6. Mater Clear ( will be used it in a factory )
7. Test Call ( will be used it in a Lab )
1. Ring / Sound
1. Ring Type
2. Volume
3. DTMF
4. 1Min Alert
5. Svc Alert
2.Tools
1. Caller ID
2. Dial Tone
3. TTY Mode
3. Time
1. Alarm
2. Auto Send Time
3. Flash Time
SXT-800U User Quick Manual
4. Setting
3/15
1. New Code
2. Restrict outgoing
3. Reset Phone
4. Voice Privacy
5. Auto gain control
5. Data Mode
1. Voice Call Mode
2. FAX Rx mode(use fax module)
3. ASYNC Data Rx mode(use data module)
4. PC FAX Rx mode
5. PC ASYNC Data Rx mode
6. FAX Tx mode(use fax module)
7. ASYNC Data Tx mode(use data module)
8. FAX Type Setting
9. FAX only
Ⅱ. Hidden Menu
SIO
‘##01’ + [ Functions ]
- You can change SIO configuration for your needs.
- As belows, SIO configuration has a DM/DS and port rate information.
- You can choose one of configurations listed at below table..
- After then, press À to make done.
- Otherwise rather than pressing À , the values will be back originally. That means “Cancel” for
what you did.
UART1 115,200 bps Serial DM to PC
UART1 9,600 bps Serial DS to PC
UART1 19,200 bps Serial DS to PC
UART1 38,400 bps Serial DS to PC
UART1 115,200 bps Serial DS to PC
UART1 19,200 bps DS to FAX
FAX 19,200 bps to PC
UART2 38,400 bps Serial DM to PC
USB DS
Ex)
##01 + 1 + À : To use UART1 for DM with 115,200 bps rate.
SXT-800U User Quick Manual
Emergency
4/15
‘##02’ + [Index]
- You can set upto 3 Emergency numbers which has up to 16 digits.
- After ##02, Following number is a [ index ] from 1 to 3 associated each emergency number.
- After you enter a index, A lockcode prompt sound will be heard immediately.
- At this time, You can enter lock code. ( a default lock code is “0000” which can be change for
your need)
- After you heard confirmation tone for a right lock code, You can set one of Emergency
numbers..
- And then press À to store it in a memory for preserving it from power-on/off cycle.
- If you press ‘#’ instead of À, What you did will be canceled..
Ex) ##021 Î lockcode prompt sound Î lock code Î911 Î À –
Sets and store a
emergecny number #1 as 911
Hotline
‘##03’
- In the Hotline Menu, you can set hotline number which will be dialled automatically whenever
you pick up handset.
- Lockcode prompt sound follows a entering a command of “##03”.
- You can enter lock code. ( a default lock code is “0000” which can be change for your need)
- After you heard confirmation tone for a lock code , You can set a Hotline number..
- And then press À to store it in a memory for preserving it on power-on/off cycle.
- If you press ‘#’ instead of À, it will be canceled.
Ex) ##03 Î enter lock code Î 39533447 + À – Sets and store a hotline as 39533447.
Mirroring ( will be used in a factory )
‘##04’
- In the Mirroring menu, you can backup/restore system configuration values of Terminal.
- Lockcode prompt sound follows a entering a command of “##04”.
- You can enter lock code. ( a default lock code is “0000” which can be change for your need)
- After you heard confirmation tone for a lock code , You can press À for backing up and ‘#’
for restoring a stored values.
- if it is succeeded, a confirmation tone will be heard and after then, a terminal will be reset.
Ex)
##04 Î enter lock code Î À – Performs backing up system values
##04 Î enter lock code Î ‘#’ – Performs restoring system values
SXT-800U User Quick Manual
5/15
A Key
‘##05’
- In the A Key menu, you can set 26 digits A Key on FWT..
- A short go-ahead tone follows a entering a command of “##05”.
- Input A Key of 26 digits .
- Pressing À will store A Key safely on FWT’s memory..
- If the entered A key is valid, you can hear confirmation tone. Otherwise, you can not..
Ex)
##05 Î 26 digits (20 digits + 6 digits checksum) Î À
Master Clear ( will be used in a factory )
‘##06’ + [ DS Baud Rate ]
- Before packing just a made product, In a factory, a phone has to makes changed value for
testing to a default values . At this time,
this commands make a FWT has default values
predifined by a operator. a command of À or ‘#’ has to follow “##06” for proper DS rate for
your system configuration. This option is needed due to FAX usually supports 19,200 rate.
- After done, the Terminal will be reset.
À
Master clear to 115,200 DS Mode
‘#’
Master clear to 19,200 DS Mode for a FAX
Ex)
##06 + À : Master clear with 115,200 option
##06 + ‘#’ : Master clear with 19,200 option
Test Call ( will be used in a lab like CDG2 )
‘##07’ + [Option]
Pressing À needs for make completed.
[Option]
NEW 8K MARKOV
FULL TDSO
NEW 13K MARKOV
SO54 MARKOV
8K LOOP BACK
SO55 LOOP BACK
13K LOOP BACK
SORS2 MARKOV
SIMPLE TDSO
SORS2 MARKOV
Ex) ##07+1+ À : Test a call for New 8K MARKOV
SXT-800U User Quick Manual
6/15
Ⅲ. Ring / Sound Menu
Ring Type
‘##11’ + [Ring type Index]
- In the Ring type menu, you can choose one of 9 ring types.
- A ring type index is needed after ##11 and a ring type index has from 1 to 9 linked by a
specific ring tone. At this moment, you can listen your choosed ring tone on your speaker or a
handset of your POTS. If you choose zero,0, It will be canceled.
- During playing a choosed ringtone, Pressing À is needed to make done. Also, choosed ring
tone will be stored on a FWT’s memory.
If you press ‘#’ instead of À, it will be canceled.
Ex)
##11+0: Canceled what you did. it will make a terminal idle.
##11+1 Î assigned ring tone Î À : Index 1’s ring tone will be selected.
##11+9 Î assigned ring tone Î À : Index 9’s ring tone will be selected.
##11+9 Î assigned ring tone Î # : Canceled what you did.
Volume level
‘##12’
- With this command, You can stay on a volume level menu until you press ‘0’ to save a
adjusted volume level.
- During staying on a volume level menu, Whenever you press À key, A voice volume will be
increased. When you press ‘#’ key, A voice volume will be decreased. Also a volume level will
be started again from a minimum level by a pressing À when last volume level reached
maximum level.
- When you meet your voice volume level, press ‘0’ to save and make done.
- If you want to cancel what you did, just press other key rather ‘0’.
DTMF
‘##13’ + [ DTMF Type]
- In the DTMF menu, you can select DTMF tone length.
- Press À to make it long, press ‘#’ to make it short.
Ex)
##13 + À : To make DTMF tone long
##13 + # : To make DTMF tone short
SXT-800U User Quick Manual
1 Min Alert
7/15
‘##14’ + [On/Off]
- you can set 1 Min alert on or off. If this option set on, An alert tone will be heared every 1
minute during a call.
- To make this alert on, a pressing À key has to follow ##14.
- To make this alert off, a pressing ‘#’ key has to follow ##14.
Ex)
##14 + À : to make a 1 min alert on
##14 + # : to make a 1 min alert off
Service Alert
‘##15’ + [On/Off]
- You can set Service alert on or off. If this option set on, An alert tone will be heared whenever
FWT lost a signal or is getting a network.
- To make this alert on, a pressing À key has to follow ##15.
- To make this alert off, a pressing ‘#’ key has to follow ##15.
Ex)
##15 + À : to make a service alert on
##15 + # : to make a service alert off
SXT-800U User Quick Manual
8/15
Ⅳ. Tools Menu
Caller ID
‘##21’ + [Caller ID type[
- You can select CID type for a caller id type of your POTS.( Default type is non cid )
- There are 3 types of caller ID as belows.
- When you choose one of them after entering ##21, press À to make complete
- Press ‘#’ to cancel what you did.
1. BELLCORE
2. V.23
3. DTMF
4. None CID
Ex)
##21 + 3 + À : to set a caller id type as DTMF caller id.
##21 + 4 + À : to make a displaying of a caller id off.
Dial Tone
‘##22’ + [Dial tone Type[
- You can select a dial tone type for your country.
- There are 4 types as belows.
- At the end of the command, Press À to set. Press ‘#’ to cancel.
1. Default
2. Latin
3. China / Nicaragua
4. India
Ex)
##22 + 1 + À : to set a dial tone as a default dial tone.
##22 + 4 + À : to set a dial tone as an india dial tone.
TTY Mode
- You can set Full TTY mode.
Press À to set, Press ‘#’ to release.
Ex) ##23 + À : Set Full TTY mode on.
‘##23’
SXT-800U User Quick Manual
9/15
Ⅴ. Time Menu
Alarm
‘##31’ + [HHMM]
- You can set the alarm time.
- After entering ##31, immediately short go-ahead tone will be heard.
- Enter 4-digits for an alarm time like as ‘HH-MM’ of 24 hour type.
- After entering an alarm time. press À to alarm on.
- To turn an alarm off, Press ‘#’ key after entering this command of ##31.
Ex)
##31 + 1540 + À : to set an alarm time to PM 3 oclock 40 minute. .
##31 + # : to cancel predefined alarm time. ( means turn an alarm off )
Auto send time
‘##32’ + [Index of Time Table]
- You can set auto send time which is setting as 5 secs defaultly..
- Auto send time will be able to be set as from 1 sec to 10 secs according to a index as below..
- After entering a time index, press À to set.
- Press ‘#’ to cancel what you did,
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.5
Linearized : No
Page Count : 16
XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6
About : uuid:fdec415d-7f35-4197-b943-1ba00cf70dc2
Producer : Acrobat Distiller 6.0 (Windows)
Company : SUNG-IL
Source Modified : D:20041207111552
Headline :
Creator Tool : Acrobat PDFMaker 6.0 for Word
Modify Date : 2004:12:21 15:09:59+09:00
Create Date : 2004:12:07 20:18:37+09:00
Metadata Date : 2004:12:21 15:09:59+09:00
Document ID : uuid:2f3ac963-9239-4ead-b58b-132e0d8c97dc
Version ID : 87
Format : application/pdf
Title : Terminal User Manual
Creator : leenon
Subject :
Tagged PDF : No
Author : leenon
