Escort orporated M7R Front Radar Receiver User Manual Installation

Escort Incorporated Front Radar Receiver Installation

UserManual.wiki >

Escort orporated >

M7R User Manual >

User Manual - Installation.pdf HTML Version

1. User Manual - Installation.pdf
2. User Manual - Owners.pdf

User Manual - Installation.pdf

360°

Alerts

The World’s Most Advanced Detection System

The most powerful & complete

protection available

MAX Ci 360

Dual Antenna Front

and Rear Protection

True Stealth Operation Lets

You Drive 100% Undetected

360° Directional

Alert Arrows

ESCORT Live App Provides

Crowd Sourced Alerts

GPS Intelligence

Rejects False Alerts

Laser Shifters Provide

Speed of Light Protection

Installation Manual

Designed in the USA

ESCORT Inc.

5440 West Chester Road

West Chester OH 45069

800.433.3487

EscortRadar.com

SpecDisplayTM, TotalShieldTM, ExpertMeterTM, ESCORT LiveTM, IVT FilterTM and EZ Mag MountTM are trademarks of ESCORT, Inc.

FCC NOTE:

Modications not expressly approved by the manufacturer could void the user’s FCC granted authority to operate the equipment.

FCCID: QKLM7R, FCCID: QKLM3R2, CONTAINS FCCID: QKLBT2

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received including interference that may cause undesired operation.

In-dash Display Bezels

• For a factory-installed look, use either the black or

platinum in-dash bezel for easy mounting to

instrument pod, dashboard, or console.

• Integrated adhesive backing for secure mounting

Control Module

• Controller mounts easily to instrument pod,

dashboard, or console

• Adhesive pads provided for secure mounting

Interface

• Central module connects to switched 12-volt

power and ground

• All components plug directly in using modular

connections

Concealed Alert Indicator

• Multi-color indicator is:

• Blinking red when receiving an alert

• Solid orange when receiving a locked-out alert

• Solid green when power is ON

• Solid blue when connected to the ESCORT Live

smartphone app

• 6-foot cable with modular connector

• Bezel provided mounts easily to instrument pod,

dashboard, or consol

Rear Laser ShifterMax Sensors*

(optional)

• Twin weatherproof sensors

• 6-foot cables with waterproof connectors

• 4 x 10-foot extension cables

• Mounting hardware

ShifterMax Bridge Box

• Weatherproof Bridge Box is used to connect

ShifterMax Sensors to main Interface

GPS Antenna

• Weatherproof magnetically mounted GPS

Antenna

• 30-foot cable with modular connector

Display Module

• Display mounts easily to instrument pod,

dashboard, or console

• Two bezels provided for optional in-dash

mounting

• Adhesive pads provided for secure mounting

* Included with ESCORT MAX Ci 360

Front Radar Receiver

• Weatherproof radar receiver

• Two universal mounting brackets with stainless

steel hardware

• Built-in 3-foot cable with waterproof

connector

• 13-foot cable with waterproof connector and

inline grommet

• 12 nylon wire ties to secure cable

Rear Radar Receiver* (optional)

• Weatherproof radar receiver

• Two universal mounting brackets with stainless

steel hardware

• Built-in 2.9 foot cable with waterproof connector

• 13-foot cable with waterproof connector and

inline grommet

• 12-foot extension cable with waterproof

connectors

• 12 nylon wire ties to secure cable

Front Laser ShifterMax Sensors

• Twin weatherproof sensors

• 6-foot cables with waterproof connectors

• Mounting hardware and bubble level

ESCORT MAX Ci Components

2 3

Radio Mute Cable

• 6-foot cable connects to compatible vehicle

audio systems and automatically mutes the

audio during alerts

Download Data Cable

• Provides access to update data via the Internet

Documentation

• Comprehensive Owner’s Manual

• Installation guide

Built-in Diagnostics

• Confirms all components are operational

4 5

Important Notes Installation Instructions

Installation Tips

While following the steps throughout this

manual, please refer to the following

recommendations for a professional, trouble-

free installation:

1 Determine the best location for the radar

receiver. The best location is typically under

the bumper, or inside the front grill of the

vehicle. For the best radar performance, install

the radar receiver horizontally, with a clear

“view” of the road.

2 Entry points into the interior may be located

behind the plastic liner in the wheel well, fuse

box, or unused grommets.

3 There are often many existing entry points

at the rear of the vehicle as well:

• Gaskets behind license plates, around

illumination lamps, and near trunk lid hinges.

• Tail light wiring gaskets are often easily

accessible and large enough to add cables.

4 If there are no suitable openings, it will be

necessary to drill a hole through the firewall:

a. Thoroughly investigate all locations

before drilling any holes! Ensure no wires,

hoses, or other vehicle components will be

damaged.

b. On vehicles with automatic transmissions,

there is often a location for mounting a

clutch pedal. This location is typically an

ideal location to drill.

c. Before drilling, cover the surface being

drilled with masking tape to prevent

damage to the anti-corrosion coating in the

event the drill bit slips.

d. Drill a 13/32" or 7/16" hole.

5 When pulling the inline grommet to the

entry point, apply rubbing alcohol to a section

of the cable to reduce friction and quickly pull

the grommet along the length.

6 The cables of units mounted at the rear of

the vehicle can generally be routed through

the trunk compartment and concealed under

trim panels quite easily. If necessary, the cables

can also be routed under the vehicle and

through an opening in the firewall. Be sure to

secure cables away from moving parts and hot

surfaces.

7 A quality crimper for modular connectors

can be used to cut cables to length and replace

the connector. Removing the connectors may

also make it easier to enter the vehicle’s interior

through existing openings.

Note:

• Only an exact replacement for the

standard connector can be used. Do not

attempt to cut the wires unless the proper

connector and crimping tools are available.

• Connectors cannot be reused.

• Do not cut the cable too short! Provide

enough cable to route to the Interface and

add a couple extra feet to ease installation

• Install the new connector such that its

locking tab is on the same side as the color

coded stripe on the cable.

• Do not attempt to cut the cable and splice

the wires together.

8 When drilling or cutting interior trim panels

(for instance, when installing the Concealed

Installation Alert Indicator or the optional

Display Bezel), first cover the surface of the

panel with masking tape to prevent accidental

scratches.

E Read This First

Please read these instructions in their entirety

before starting your installation.

For the easiest, trouble-free installation, install

the interface first and wire it to a 12-volt

switched circuit.

Then, before installing the other components,

plug all of them into the interface and power

up the unit to confirm proper operation.

Installation Warnings

1 It is recommended that you have a

professional install your new ESCORT MAX Ci .

Installation of this system requires experience

and expertise in automotive electronics. If you

are unfamiliar with automotive electronics, car

audio specialists and many car dealers can

install your ESCORT MAX Ci for you.

2 Attempting to install this product without

expertise in automotive electronics installation

can cause personal injury or damage to your

vehicle.

3 If your vehicle is damaged during

installation its safety systems may be

compromised, which could cause personal

injury or property damage.

4 Improper installation may void ESCORT

MAX CI’s warranty.

Performance Warning

To get the best performance possible, the

mounting location of the radar receiver is

critical. Although radar signals will pass

through some types of plastic, mounting

the radar receiver so that it has a clear

“view” of the road will ensure maximum

warning.

Since Laser signals will not pass through

objects, including most plastics, it is critical

that the Laser Shifters are mounted

perfectly level and have an unobstructed

“view” of the road.



6 7

Front Radar Receiver (Continued)

5 Find a suitable entry point into the vehicle’s

interior. Refer to the Installation Tips section.

6 Feed the harness into the vehicle’s interior

and to the Interface. Plug into the connector

labeled “Front Receiver.”

7 If entering through a drilled hole, pull the

grommet on the harness until the end sticks

through the hole. From inside the vehicle, pull

grommet through until it seals against the

outer surface.

ShifterMax Bridge Box

1 The Bridge Box is weatherproof. To limit the

number of cables routed through the firewall,

we recommend installing the Bridge Box

inside of the engine compartment.

2 Slide the included heatshrink onto the

Bridge Box Interface cable then plug into the

cable extending from the Bridge Box labeled

“Interface” and route the cable toward the

interior of the vehicle. Shrink the heatshrink

onto the inline connector and secure the cable

with zip-ties. Although waterproof, it is best to

locate the inline connector in a dry area

protected from moving parts, road debris, and

hot surfaces such as the radiator and radiator

hoses.

Front Laser ShifterMax

Sensors

Positioning Sensors

Install each sensor halfway between the side

and the center of the vehicle.

For optimal performance sensors need to be

completely unobstructed, not behind a grille,

level and facing straight forward (rearward if

installing optional rear sensors*). Make sure

that each sensor is parallel with the road

(using supplied bubble level).

Note:

Vehicle must be positioned on a flat surface

in order to position sensors parallel with the

road. Make sure that sensors have an

unobstructed “view” of the road so the unit

can function properly. Do not install sensors

behind a solid surface, which would block

laser transmission/reception.

Interface

1 Install the Interface under the dash using

supplied zip-ties.

Note:

Do not mount Interface inside vehicle’s

engine compartment!

2 Connect black wire (-) to ground, and

red-striped wire (+) to a switched 12-volt

supply. (If ESCORT MAX Ci is left in the “on”

position, it will automatically power on and off

with the ignition).

3 Front Radar Receiver, ShifterMax Bridge Box,

Display and Control Modules, GPS Antenna,

Concealed Alert LED, Radio Mute Cable, and

optional Rear Radar Receiver* all plug into the

Interface.

4 It is recommended that after the Interface is

installed and connected to power, all other

components are plugged in and tested for

proper operation before completing the

installation.

IMPORTANT! When using optional Rear

ShifterMax sensors* ensure DIP switches 3

and 4 are moved down to the REAR

SHIFTER position. See the Interface

illustration on pg 9.

* included with ESCORT MAX Ci 360

Front Radar Receiver White Stripe

1 Determine the best location for the Radar

Receiver. The best location is typically under

the bumper or inside the front grille of the

vehicle. For the best radar performance install

the Radar Receiver flat, horizontally, not on its

side.

2 Using the supplied U-shaped bracket and

the right-angle mounting bracket, mark the

mounting location. Drill pilot holes in the

vehicle if necessary.

3 Mount the Radar Receiver using the

supplied hardware. It is recommended that the

Radar Receiver is secured to the brackets first,

and then the brackets and Receiver mounted

to the vehicle.

4 Slide the heatshrink onto the Radar Receiver

cable then plug into the harness and route the

cable toward the interior of the vehicle. Shrink

the heatshrink onto the inline connector and

secure the cable with zip-ties. Although

waterproof, it is best to locate the inline

connector in a dry area protected from moving

parts, road debris, and hot surfaces such as the

radiator and radiator hoses.

A B D

8 98 9

Installation Schematic Overview

IF G HE

Letter References For Components (Color Coded Connections To Interface)

A Interface

B Front Radar Receiver (White Stripe)

C Front ShifterMax Sensors (plug into ports 1 & 2 on ShifterMax Bridge Box)

D ShifterMax Bridge Box (plugs into Interface using supplied cable with no

stripe or shrink)

E GPS Antenna (Yellow Shrink)

F Display Module (Orange Shrink)

G Control Module (Blue Shrink)

H Concealed Alert Indicator (Gray Shrink)

I Rear Radar Receiver (optional, included with ESCORT MAX Ci 360)

J Rear ShifterMax Sensors (optional, included with ESCORT MAX Ci 360)

Optional Components

(Included with ESCORT MAX Ci 360)

ShifterMax Bridge Box

1 The Bridge Box is weatherproof so

it can be installed in the engine

compartment or under the dash.

2 Connect Front ShifterMax Sensors

to ports 1 and 2 of the Bridge Box.

3 Connect Rear ShifterMax Sensors

to ports 3 and 4 of the Bridge Box.

4 The Bridge Box connects to the

Interface using the supplied cable

with a 6 pin modular plug on one

end and a round shifter plug on

the other end.

GPS Antenna Yellow Shrink

1 Determine the best location for the GPS

antenna. The GPS Antenna requires a clear

view of the sky. The magnetic base can be used

on most vehicles to mount to the roof of the

car or the trunk lid. It can also be mounted to

the dashboard or rear deck using double-sided

tape.

2 Mount the GPS Antenna, being sure that

roof racks or other obstructions do not block

its view of the GPS satellites.

3 Locate a suitable entry point into the

vehicle. Refer to the Installation Tips section for

locating a suitable entry point.

4 Route the cable through the entry point and

secure along its path. If mounting near the

front or rear window, it is usually possible to

tuck the cable under the gasket surrounding

the glass.

5 Once inside the vehicle’s interior, route the

cable to the Interface and plug into the

connector labeled “GPS.”

6 Secure and conceal the cable under interior

trim panels.

Display Bezel Mounting

1 The supplied display bezel can be used to

mount the Display permanently in the dash or

console.

2 Determine the best location for the Display

Module. If installed by a professional, the

customer should be consulted. A flat, plastic

surface with no obstructions behind it is best

for this type of mounting.

3 Cover the mounting surface with masking

tape to prevent accidental scratches.

4 Using the supplied hole template, mark the

location.

5 Ensure there are no hidden cables, brackets,

or other components behind the location, and

that there is adequate clearance behind the

panel. The Display will protrude into the dash

or console by 1/2".

6 Very carefully cut the hole in the mounting

surface.

7 Feed the display module cable through the

bezel and the opening in the dash then route it

to the interface.

8 Remove the masking tape protecting the

trim panel.

9 Clean the mounting surface thoroughly.

10 Apply the double-sided adhesive tape to

the display bezel.

11 Mount the Display Module using the bezel

adhesive.

12 Plug the connector into the Interface

connector labeled “Display Module.”

13 Secure and conceal the cable under trim

panels.

10 11

Front Laser ShifterMax

Sensors

(Continued)

1 Snap mounting bracket onto sensor and

install the included bolts but do not tighten

them. If the bolts do not thread into the sensor

then you have the bracket on backwards.

2 Apply the double sided tape to the

underside of the sensor’s mounting bracket.

Check front alignment and mount the sensor

to a solid surface of the vehicle.

3 Use the supplied bubble level to ensure the

sensor is parallel to the road and tighten the

sensor’s mounting bracket bolts.

4 Repeat for additional sensor(s).

Securing Connectors with Shrink Tube

Once you’ve installed all components properly

and tested to ensure all parts are working

properly, use cable ties to fasten sensor cables

to a solid surface, keeping them away from

heat and any moving parts. It is advisable to

use the supplied heatshrink tubes to protect

connectors against water, moisture, dust, etc.

IMPORTANTLY the ShifterMax sensors are

shipped in “receive only” mode. Shifting

must be enabled in the bands settings. See

the Preferences section of the Owner’s

Manual.

Additional ShifterMax Sensors

• ESCORT MAX CI users wanting to add rear

sensors, two (2) additional ShifterMax

Sensors with included hardware are sold

separately.

Display Module Orange Shrink

1 Determine the best location for the Display

Module. If installed by a professional, the

customer should be consulted. An optimal

location is clearly visible from the driver’s

position and does not take a driver’s eyes off

the road for more than a moment.

2 Clean the mounting surface thoroughly.

3 Mount the Display using the pre-applied

adhesive.

4 Route the cable to the Interface and plug

into the connector labeled “Display Module.”

5 Secure and conceal the cable under trim

panels.

Control Module Blue Shrink

1 Determine the best location for the Control

Module. If installed by a professional, the

customer should be consulted. An optimal

location is easily visible and accessible from

the driver’s position, and does not interfere

with normal driving. Avoid locations that

require reaching through or around the

steering wheel.

2 Clean the mounting surface thoroughly.

3 Mount the Control using the pre-applied

adhesive.

4 Route the cable to the Interface and plug

into the connector labeled “Control Module.”

5 Secure and conceal the cable under trim

panels.

Concealed Alert

Indicator Gray Shrink

1 Determine the best location for the Alert

Indicator. If installed by a professional, the

customer should be consulted. An optimal

location is clearly visible from the driver’s

position and does not take a driver’s eyes off

the road for more than a moment.

2 Ensure there are no hidden cables, brackets,

or other components behind the mounting

location, and that there is adequate clearance

behind the panel.

3 Cover the mounting surface with masking

tape to prevent accidental scratches.

4 Carefully mark the location and drill a 1/4"

hole through the mounting panel.

5 Remove the masking tape protecting the

trim panel.

6 From the front side, snap one of the panel

bezels provided into the hole.

7 Snap the Alert Indicator into the panel bezel

from the back side.

8 Route the cable to the Interface and plug

into the connector labeled “Concealed Alert

LED.”

9 Secure and conceal the cable under trim

panels.

USB Update Cable

The USB Update cable allows updating the

ESCORT MAX Ci’s DEFENDER database and

firmware. ESCORT MAX Ci’s red light and speed

camera DEFENDER database is easily updated

using our exclusive detector software tools

found on our web site. Firmware, or the

operating software for the detector, can also

be updated using these tools.

In order to have access to these updates,

please register your ESCORT MAX Ci at www.

EscortRadar.com. Once registered, you will

receive email notifications when updates are

available.

12 13

GH Rear Radar Receiver* optional

1 Follow the same installation instructions as

for the Front Radar Receiver but with the

receiver’s arrow oriented to point out the rear

of the vehcle.

2 Entry points to the vehicle’s interior may be

available behind the license plate or lights.

Rear Laser ShifterMax

Sensors* optional

IMPORTANT! When using optional Rear

ShifterMax sensors* ensure DIP switches 3

and 4 are moved down to the REAR

SHIFTER position. See the Interface

illustration on pg 9.

1 Follow the same installation instructions as

for the Front Laser ShifterMax Sensors but with

the sensors oriented to point out the rear of

the vehicle.

2 Entry points to the vehicle’s interior may be

available behind the license plate or lights.

Radio Mute Cable

1 The radio mute cable (included) allows the

detector to be connected to compatible audio

systems with a “Radio Mute” wire or connector.

Once connected, the audio level of the stereo

is reduced automatically during an alert.

2 Please refer to your audio system’s manual

for proper connection to your audio system.

Operation Test

After all components are installed correctly:

1 Turn ESCORT MAX Ci on by turning on the

vehicle’s ignition and, if necessary, press the

power button on the Control Module.

2 ESCORT MAX Ci will cycle through a startup

sequence.

3 If any error messages come up, see the

Owner’s Manual troubleshooting section for

Escort orporated M7R Front Radar Receiver User Manual Installation

Escort Incorporated Front Radar Receiver Installation

Contents

User Manual - Installation.pdf

Navigation menu

Namespaces

Views

Navigation