Evenflo 900T646SENSA Baby Monitor User Manual 85 923 001 001 Eng ai

Evenflo Company, Inc. Baby Monitor 85 923 001 001 Eng ai

User Manual

The Parent’s Unit (Receiver)The Parent’s Unit receives sound fromthe Baby’s ’sUnit (transmitter)and is powered by eitherrechargeable batteries (already in the unit) or by the AC adapter included with the unit.1. Ensure Parent’s Unit is charged. To charge, connect AC adapter (provided) to Parent’s Unitand plug into standard wall outlet. To charge while monitoring, set Power/Volume Dial toON. A full charge requires 12 continuous hours.2. Check the channel switch. Ensure the Baby’s Unit is set to the same channel as theParent’s Unit.3. Use the Parent’s Unit in a different room from the Baby’s Unit.4. Place the Parent’s Unit where you can easily monitor it by sight or sound.• When using the adapter, plug it into a standard wall outlet.• When using batteries, wear the Parent’s Unit using the belt clip or place it where you can easily see or hear it.5. Turn on the Parent’s Unit by rotating the Power/Volume Dial; adjust the volume. ThePower Light will glow green. If the Power Light flashes, it indicates that battery power islow and Parent’s Unit needs to be recharged. NOTE: All sound Lights™ will light up andflash on the Parent’s Unit if it is not properly receiving signals from the Baby’s Unit.6. Have someone speak into the Baby’s Unit to verify sound transmission.7. Turn the Parent’s Unit OFF when not in use.The Baby’s Unit (Transmitter)The Baby’s Unit is a transmitter, which sends sounds to the Parent’s Unit (receiver). It is poweredby a hardwired (non-removable) AC adapter.1. Place the Baby’s Unit on a hard flat surface that is higher than the baby and 5 to 10 feet away(refer to illustration).• DO NOT place the Baby’s Unit directly above the baby.• DO NOT place it on a soft surface or it may tip over.2. Direct the front of the Baby’s Unit towards the baby. Be sure that there aren’t any largeobjects blocking the path between the Baby’s Unit and the baby.3. Fully extend the cord, and plug the adapter into an electrical outlet.4. Rotate the Power Switch from OFF to ON. The Power Light will glow green.5. Slide the Channel Switch to Channel A or B. Ensure the Baby’s Unit is set to the samechannel as the Parent’s Unit.6. Turn Pet Detection ON or OFF, as desired.7. Turn the Baby’s Unit OFF when not in use.WhisperConnectTM Sensor900 MHz Nursery Monitor – Pet DetectionImportant: Read and keep these instructions for future reference.Answers. Advice. Affirmation.™• www.evenflo.com• USA & Canada: 1-800-233-5921• México: 01-800-706-12-00Thank you for purchasing the Evenflo WhisperConnect Pro Nursery Monitor. If you have anyquestions or problems with your Evenflo WhisperConnect Pro Nursery Monitor please do notreturn it to the store; call Evenflo’s ParentLink at 1-800-233-5921, Monday through Friday8:00 AM to 7:00 PM EST.Model Number: Your WhisperConnect Pro Nursery Monitor model number is 6461500.•DO NOT OPEN. NO USER SERVICEABLE PARTS INSIDE. RISKOF ELECTRIC SHOCK. MAY CAUSE INJURY, FIRE, OR DEATH.•DO NOT use near water.•DO NOT place furniture on cord.•NEVER place the baby’s unit or its adapter in the crib or playpen, orwithin the child’s reach.•DO NOT hang this monitor near or on a crib. The cord can presenta strangulation hazard.•Always keep the unit out of children’s reach.•DO NOT use this monitor if it is broken or missing parts.•This product is designed and intended to be used solely to monitorthe actions of a sleeping child.•DO NOT use this monitor with products that warn the user: “NEVERLEAVE CHILD UNATTENDED.”•This product does not replace responsible adult supervision of a child.•You should check your child regularly as this product will not detectyour child’s quiet activities.•This product is not intended to be used as a medical monitor, and itsuse should not replace adult supervision.•Make sure the Parent’s and Baby’s units are functioning properly, onthe same channel, and within reception range of each other.•It is essential to check the sound reception regularly.The Evenflo WhisperConnect Pro Nursery Monitor should NOT be used as a replacement for adultsupervision of children. Please note that any modification to the Baby’s Unit (transmitter) orParent’s Unit (receiver) will violate FCC compliance and can void the user’s authority to operatethis monitor set.1. Read and observe all warnings on the product and in this Owner’s Manual. Pay specialattention to information marked “WARNING” and “IMPORTANT.” This information can affectyour child’s safety. Keep this Owner’s Manual nearby for quick and easy reference.2. Avoid placement near water or moisture. DO NOT use Baby’s Unit outdoors. DO NOT useyour monitor near a bathtub, shower, sink, laundry tub, swimming pool, wet basement, orother locations where water or moisture may result in electrocution.3. Allow for proper ventilation of the adapters and the monitors. DO NOT place your monitor onor under a rug, bed, sofa, blanket or similar object that blocks its ventilation. DO NOT place itin a built-in installation such as a bookcase or stereo cabinet. These may impede the air flowthrough the ventilation openings.4. Remove the batteries from the monitor components and unplug the AC adapters if themonitor will not be used for a long period of time.5. Avoid placement near heat sources. DO NOT use your monitor near a radiator, stove, heatregister, or other appliance (including amplifiers and TV’s) that produce heat. Heat can damagethe case or components. Troubleshooting GuideNOTE: If, after checking all of the solutions below, you believe that your WhisperConnnect Parent/Baby Unit is damaged, please call ParentLink at 1-800-233-5921.For a period of 90 days from the original purchase of this Product, Evenflo warrants to the original end user("Purchaser") this Product (including any accessories) against defects in material or workmanship. Evenflo’ssole obligation under this express limited warranty shall be, at Evenflo’s option, to repair or replace anyProduct that is determined to be defective by Evenflo and determined to be covered by this warranty.Repair or replacement as provided under this warranty is the exclusive remedy of the Purchaser. Proof ofpurchase in the form of a receipted invoice or bill of sale evidencing that the Product is within the warrantyperiod must be presented to obtain warranty service. This express limited warranty is extended by EvenfloONLY to the original Purchaser of the Product and is not assignable or transferable to subsequent purchasersor end users of the Product. For warranty service, contact Evenflo’s ParentLink Consumer Resource Center at(800) 233- 5921 or www.evenflo.com.Limited WarrantyEXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OFMERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS HEREBYDISCLAIMED. EVENFLO SHALL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL ORPUNITIVE DAMAGES OF ANY KIND FOR BREACH OF THE EXPRESS LIMITED WARRANTY ON THISPRODUCT, OR ANY WARRANTY IMPLIED BY OPERATION OF LAW. OTHER THAN THE EXPRESSLIMITED WARRANTY SET FORTH ABOVE, THERE ARE NO OTHER WARRANTIES THAT ACCOMPANYTHIS PRODUCT AND ANY ORAL, WRITTEN OR ANY OTHER EXPRESS REPRESENTATION OF ANY KINDIS HEREBY DISCLAIMED.•Make sure BOTH units are properly plugged into the wall and the outlet isswitched on.•Make sure both the Parent’s Unit and the Baby’s Unit are set to the same channel.•Recharge battery by attaching the AC adapter and plugging it into an outlet.Power Light isn’t working. Unit isn’t getting power.•Turn off, unplug or move the device that is causing the problem.•Move the Parent’s Unit closer to the Baby’s Unit.•Recharge battery by attaching the AC adapter and plugging it into an outlet.•Other household appliances, cordless phones, fluorescent lightsor motors may be disrupting the signal.•Parent’s Unit may be out of effective range.•Battery is weak.Reception is poor due tostatic, buzzing orinterference.SOLUTIONPOSSIBLE CAUSEPROBLEM•Move the Parent’s Unit at least 10 feet away from the Baby’s Unit.•Lower the volume.Change the frequency channel that is in use. Be sure to change the channel on BOTH units.A neighbor has a similar baby monitor, cordless phone orwalkie talkie that is transmitting sounds on the samefrequency channel.Parent’s Unit is picking upsounds or static fromoutside your home.Parent’s Unit is making aloud feedback noise. •Baby’s Unit is picking up sounds from the Parent’s Unit becausethey are too close to each other.•Volume may be set too high.Battery is weak.Power Light flashes(Parent’s Unit only).Recharge battery by attaching the AC adapter and plugging it into an outlet.•Move Parent’s Unit closer to the Baby’s Unit.•Make sure that both units are set to the same channel.•Turn the Power Switch on the Baby’s Unit to the ON position.•Check the AC outlet to be sure it is working.•Recharge battery by attaching the AC adapter and plugging it into an outlet.All Sound Lights flash andalarm sounds (Parent’sUnit only).•Parent’s Unit is outside the transmission range of the Baby’s Unit.•Baby’s Unit and Parent’s unit are on different channels.•Baby’s Unit is not turned on, or not plugged into a working outlet.•Battery in Parent’s unit is weak.WARNING WARNINGAC AdapterAntennatect.LenswitchFinder ButtonPet Detect.ON/OFFPower LightChannel SwitchSpeakerAdapter Jack Sound LightsPower/Volume DialPower Light/Low Battery IndicatorChanSwitAntennaAC AdapterPet Detection LightImportant Safety InstructionsUL Listed Adapter. FCC Approved.6. The Baby’s Unit (transmitter) is operated by a hardwired (non-removeable) AC adapter.DO NOT attempt to remove the AC adapter; doing so can affect your safety. The Parent’sUnit (receiver) is operated by rechargeable batteries that are included with your monitor orby the Evenflo AC adapter (provided). Use only the Evenflo adapter included with this unit.DO NOT use this adapter with other equipment or use other equipment s’ adapters with thismonitor under any circumstances.7. Protect the AC adapter cords. Route cords so they are not walked on, pinched by itemsplaced upon them, or run-over by vacuum cleaners.8. DO NOT immerse any component in water. Clean the monitor with a dry cloth.9. DO NOT use near fluorescent lights, appliances with motors, televisions, fans or othermachinery. These items may interfere with the quality of your monitor’s transmission orreception.10.Adapter must be removed from the receiver for battery operation.11.DO NOT use the monitor if:•Either adapter cord has been damaged.•Objects have fallen onto or liquid has been spilled into any of its components.•It has been exposed to rain or water.•It has been dropped or something inside is damaged.•If any parts are missing or broken, call Evenflo’s ParentLink at 1-800-233-5921 forinstructional literature or product information if needed.12.Refer to the Troubleshooting Chart in this Owner’s Manual before returning your monitorfor servicing. You may be able to solve the problem on your own in very little time.13.There are no serviceable parts inside these monitors. DO NOT open the cases.14.This device complies with part 15 of the FCC rules. Operation is subject to the following tw oconditions: (1) This device may not cause harmful interference, and (2) this device mus taccept any interference received, including interference that may cause undesired operation.•For best results, use your AC adapter(s) with the monitor. The power is more consistent thanthat of the battery.•For best battery performance, allow batteries to completely discharge every few weeks.•This nursery monitor operates over public airwaves. Transmissions from your Baby’s Unit maybe picked up by another product operating on the same frequency. Your Parent’s Unit mayalso pick up transmissions from another product on the same frequency. If interferenceoccurs, change BOTH your Baby’s and Parent’s Units to the alternate frequency channel.•Always make sure that both units are on the same frequency channel. It is possible for theParent’s Unit to pick up the Baby’s Unit even if they are not on the same channel when bothunits are close together; however, you’ll experience static and interference.Changes or modifications to this unit not expressly approved bythe party responsible for compliance could void the user’s authorityto operate equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to part 15 of the FCC rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. Thisequipment generates, uses and can radiate radio frequency energy, and if not installedand used in accordance with the instructions, may cause harmful interference to radiocommunications.There is no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and Parent’s Unit (receiver).•Connect the equipment into an outlet on a circuit that is different from the Parent’s Unit (receiver).•Consult the dealer or a qualified radio-TV technician for help.Operational Range: Your monitor’s typical transmission/reception range is 650 feet (198 m)depending on battery power and possible obstructions (i.e., walls) that radio waves encounter. Themethods and materials used in your home’s construction, terrain and other factors may also affecttransmission.Power Light: The Power Light will illuminate green whenever the unit is turned on, whether theunit is stationary (plugged into adapter) or portable (using battery power).Channel A/B: If interference occurs, change BOTH your Baby’s Unit and Parent’s Unit to thealternate frequency channel. The WhisperConnect Pro Nursery Monitor operates over publicairwaves. Transmission from your Baby’s Unit may be picked up by another product if it is on thesame frequency. Your Parent’s Unit may also pick up transmission from another product if it isbroadcasting on the same frequency.Sound LightsTM: Sound Lights light up when the Parent’s Unit receives sounds. The more lights thatare lit, the louder the sounds.Low Battery Indicator: When battery power in the Parent’s Unit is low, the Power Light/LowBattery Indicator will flash. To recharge, attach the AC adapter to the Parent’s Unit, plug the ACadapter into a standard wall outlet, then set Power/Volume Dial to ON.Out-of-Range Indicator and Alarm: All Sound LightsTM will light up and flash, and an alarm willsound on your Parent’s Unit if:• The units are taken out of range of one another. • The units are set to different channels.• Power to the Baby’s Unit is lost. • A strong interfering signal starts on the selected channel.The Out-of-Range Indicator and Alarm can only be stopped by re-establishing contact between thetwo units or by turning off the Parent’s Unit. This alarm feature is designed to give you confidenceand reassurance that your Evenflo WhisperConnect Pro Nursery Monitor is functioning properly.Parent Unit Finder: Press the Finder Button on Baby’s Unit to activate the locating signal. Oncethe Parent’s Unit is located, turn Power Switch OFF then ON to deactivate the signal.Additional Receivers: You may expand WhisperConnect capacity by adding additional receivers(sold separately). Use only Evenflo WhisperConnect Additional Receiver model 6461550 to expandthis monitor system. Please consult the owner’s manual included with the additional receiver forwarning and safety instructions.Helpful HintsUsing Your MonitorWhen the Pet Detection Lens senses movement within range,an alarm will sound on the Parent’s Unit and the pet detectionlight will illuminate. To deactivate/reset the alarm, turn theparent unit OFF then ON.NOTE: The Pet Detection feature is NOT active within the first20 seconds of being turned on. This allows adults sufficienttime to move out of range.Features2 ft (0.6 m)2 ft (0.6 m) ©Evenflo Company, Inc. 2004 25700006 4/044ft 3 inch (1.3m)8 ft 6 inch (2,6 m)8 ft 6 inch (2,6 m)

Navigation menu