FUJITSU TEN 74E30081000011 RFID Reader Writer User Manual

FUJITSU TEN LIMITED RFID Reader Writer Users Manual

manual

USER MANUALRFID　Reader/Writer [74Eｰ300810-0001-1D]USER MANUALRFID　Reader/Writer74Eｰ300810-0001-1D(Built-in Type)FUJITSU TEN LIMITEDVersion　1.05
USER MANUALRFID　Reader/Writer [74Eｰ300810-0001-1D]Contents1. Safety Precautions2. Outline3. Architecture4. Specification5. Names and Functions6. Installation7. Communications Specifications1.1 Warning2.1 Outline2.2 Feature2.3 In use3.1 System Architecture4.1 Specification4.2 Dimension5.1 Names and Functions of each part6.1 Installation Enviroment6.2 Connecting Cable7.1 Communications Specifications1.2 CautionFUJITSU TEN LIMITED
[1 / 8]1.1　　WarningUSER MANUALRFID　Reader/Writer [74Eｰ300810-0001-1D]1) 　In case installing this product, Turn off the power supply or remove theconnection of power cable.2)　This product is permitted by Radio regulation law in Japan. So it is not necessary to get the permission of high frequency equipment to set. And this product doesn't use except for the following country. If you use the module other than PC-180001 or remodels it, you are punished by ordinance. Changes or modifications not expressly approved by the manufacturer for compliance could void the user's authority to operate the equipment. It is punished similarly when using it in a country other than the above.3) Don't use other AC adaptor excluding our company specified. It might cause the electric shock, a fire, and the breakdown.4) This product uses electric wave. According to the place and method for use, it is danger that influences medical equipment. Observe the following strictly when operating it to reduce this influence. ①　Do not use this product in the hospital or the airport. ②　Do not use it for medical equipment. ③　Those who install the planting type medical equipment must not bring 　　 the installation part close from the antenna of the RFID equipment　　 within 22cm.＜Built-in module＞R/W module model NumberPC-180001-M AC-10008＜Electric wave acquisition country＞Country IDChinaMaxicoSpainPhilippinTｈailand１． Safety ConcernsWARNINGFUJITSU TEN LIMITED
[2 / 8]1.2　　CautionUSER MANUALRFID　Reader/Writer [74Eｰ300810-0001-1D]1)　Please avoid the installation in the following places.　　　① Enviroment that deviated from the specifications range of this product.　　　② Use in the following place　　　　　a．Locations exposed to direct sunlight.　　　　　b．Locations high temperature and high humidity.　　　　　c．Locations directly subjected to vibration and shock. 　　　　 d．Locations where a strong magnetic field or electric field occurs.　　　　　e．Locations with corrosive gas or inflammable gas.　　　　　f．Locations where condensation occurs due to sudden temperature changes.　　　　　g．Locations covered metal.2)　Content with danger of not operating normally　　　① When there is equipment which generates the electric wave in the vicinity of 13.56MHz to be near.　　　② When there are a speaker or an echo thing to be near.　　　③ When in surroundings, there is a noise source.3) Do not set up this product in an unstable place.　　It causes the breakdown when falling .4) If you don't use equipment for a long time, stop to supply power, except for pull out the AC adaptor.5) This product is a communication device that uses the electric wave of 13.56MHz. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:　　① This device may not cause harmful interference, and　　② This device must accept any interference received, including interference that may cause undesired operation.6) This product and the internal antenna must not be co-located or operating in conjunction with any other antenna or transmitter. End user cannot modify this transmitter device. Any unauthorized modification made on the device could avoid the user's authority to operate this device.7) The distance of Reader/Writer (R/W) and IC tag changes by the following.　 ① Holding of IC tag　　　② Material (set up)　　　③ Size and shape　　　④ Presence of electric conducting materialCAUTIONFUJITSU TEN LIMITED
This product is RFID Reader/Writer to be able to read and write IC tag data by non-contact by using the frequency of 13.56MHz. It is possible to use it for various usages of management of entrance and exit and the distribution management, etc.A basic control of this product becomes operation of returning the response for the command from a upper system. Even when two or more IC tag exists in the area which can be read, this product can be read. It corresponds to a standard command and two or more option commands in accordance with international standard ISO/IEC15693. Because the data of IC tag can be freely overwrited, it can repeat, and be low-cost. It is a Reader/Writer of the small size and low power consumption. As for the connection with a upper system, the connection with RS-232C or USB becomes possible. Because this product corresponds to "Inducement type reading and writing communication equipment" of "High frequency use equipment" of the Radio Law of Japan; This is applied to the Ministry of General Affairs, and the formal licensing is acquired. Therefore, the user can use it without following a procedure for the permission application of the high frequency use equipment. 2.3　In use2.1　Outline[3 / 8]2.2　FeatureUSER MANUALRFID　Reader/Writer [74Eｰ300810-0001-1D]2. OutlineRS-232CRS-232CCN3CN1CN2USBＤ-ｓｕｂ ９pin⇔RJ45Ｄ-ｓｕｂ ９pi⇔RJ45Series A Plug⇔Series B PlugConnector Connecting Cable ＳpecificationConnector No.Transmission／ReceptionTransmissionTransmission／ReceptionCommunicationFUJITSU TEN LIMITED
This product communicates with the lower system (IC tag) and the upper system (computer and PLC, etc.). This product can change operation by sending the command from the upper system. Power is supplied by Reader/Writer's electric wave when IC tag enters in the antenna area, and the Reader/Writer is communicated. The communication with the upper system passes serial I/F or USB I/F. Connection with ComputerConnection with PLC3.1　System Architecture[4 / 8]USER MANUALRFID　Reader/Writer [74Eｰ300810-0001-1D]3. ArchitectureComputerＣommunication with the upper systemReader/WriterIC tagＣommunication withthe ｌower systemRS-232CUSB Exclusive AC adaptorDC5V supplyIC tagＣommunication withthe ｌower systemＣommunication with the upper systemRS-232CPLC Reader/WriterRS-232C　ModuleExclusive AC adaptorDC5V supplyFUJITSU TEN LIMITED
This product is RFID Reader/Writer to be able to read and write IC tag data by non-contact by using the frequency of 13.56MHz. It is possible to use it for various usages of management of entrance and exit and the distribution management, etc.A basic control of this product is operation of returning the response to the command from the upper system. *1) "Tag-it HF-I" is a registered trademark of the TEXAS INSTRUMENTS Inc. 　　　"I.CODE SLI" and "MIFARE" are registered trademarks of the NXP Semiconductors Ltd. 　　　"Felica" is a registered trademark of the Sony Corporation. 　　　"Felica" is a technological method of the contactless IC card which the Sony Corporation developed. *2) It is a value for opposing the card tag and the antenna correctly. The value is different depending on the system requirements and the tag type. Please see "Multi protocol R/W module software specifications" about the specification of software. [5 / 8]4.2　Dimension4.1 SpecificationUSER MANUALRFID　Reader/Writer [74Eｰ300810-0001-1D]4.SpecificationItem SpecificationsReader/Writer Module PC-1080001-M (Japan Formal Licensing No.: AC-10008)frequency 13.56 MHz ± 7kHzCommunication Range (*2) Tag-it : 80mm (Max.)MIFARE : 40mm (Max.)Felica : 35mm (Max.)Applied tag (*1) ISO15693 (Tag-it Plus/Pro, I･CODE SLI)ISO14443 (MIFARE Classic, MIFARE Ultralight)Felica (ID read only)Working Temperature 0℃ - 60℃Dimensions 60 mm X 95 mm X 25 mm (Exclude the installation flange)Working Humidity 30% - 85%R.H. （Non condensing）Communication Command Multi Protocol Reader Writer Module (PC-1080001)(Refer to Software Specification)Ｉ／Ｆ Serial CommunicationBaud Rate: 19200bps (+ 0.32%)Transmission Method: Asynchronous Communication MethodData Structure: Data Length: 8bit, Stop Bit: 1bit, Non ParityError Detecting: BCC MethodResponse Method: ResponseRated Power DC 5V 10VAFUJITSU TEN LIMITED
①RS-232C ConnectorIt is a connector of a Reader/Writer and the PC. The communication protocol is RS-232C. (flow control is not done)In case connect to the PC, use the crossing cable of D-sub 9P (female) connector and RJ45 connector. Turn on the left of ③Communication SWCable (Recommended) ：　CBL-RJ45F9-150　（ＭＯＸＡ）Show the signal name the table below.ＲＳ－２３２Ｃ（Ｄ sub connector ９Ｐ） ＲＳ－２３２Ｃ（ＲＪ４５ connector）②USB ConnectorIt is a connector of a Reader/Writer and the PC.In case connect to the PC, use the USB cable.Turn on the right of ③Communication SWShow the signal name the table below.USB connector (Standard B) ④Power Adapter JackIt is an input terminal; DC5V.Exclusive ＡＣ Adapter　：　ＵＳ３０－０５２０ <correspondence ＣＥ marking>　[UNIFIVE CO.,LTD.]Rated Power ：AC100V-AC240V(50/60Ｈz) 12W、0～50℃Voltage(OUT)：+5V、Current(OUT)：2A、Plug specification ：EIAJ Voltage division2Do not use exclusive AC adapter.5.1　Names and Functions of each part[6 / 8]USER MANUALRFID　Reader/Writer [74Eｰ300810-0001-1D]5. Names and Functions①ＲＳ－２３２Ｃ Connector（ＲＪ４５）＜Transmission／Reception＞ＲＳ－２３２Ｃ Connector（ＲＪ４５）＜Transmission＞②ＵＳＢ Connector（Standard Ｂ）＜Transmission／Reception＞④Power Adapter Jack（ＥＩＡＪ－＃２）Center Position of Antenna③Communication SWPin No. Name Function１Ｖｂｕｓ +5V２-Ｄａｔａ（Ｄ－） Data Line３＋Ｄａｔａ（Ｄ＋） Data Line４ＧＮＤ ＧＮＤPin No. Abbreviation Name１ＤＳＲ Data Set Ready２ＲＴＳ Request to Send３ＧＮＤ ＧＮＤ４ＴｘＤ Transmitted Data５ＲｘＤ Received Data６ＤＣＤ Data Carrier Detect７ＣＴＳ Clear to Send８ＤＴＲ Data Terminal ReadyPin No. Abbreviation Name１ＤＣＤ Data Carrier Detect２ＴｘＤ Transmitted Data３ＲｘＤ Received Data４ＤＳＲ Data Set Ready５ＧＮＤ ＧＮＤ６ＤＴＲ Data Terminal Ready７ＣＴＳ Clear to Send８ＲＴＳ Request to Send９ ---WARNINGFUJITSU TEN LIMITED
6.1.1　GeneralPlease avoid the installation in the following places.・Enviroment that deviated from the specifications range of this product.・Direct sunlight・High temperature and high humidity・Vibration・Strong magnetic force and shock voltage w・Firedamp・Condensation or temperature excursion・An electrically charged thing・Do not use in the hospital or the airport.・Do not use it for medical equipment. ・Those who install the planting type medical equipment must not bring the installation part close from the antenna of the RFID equipment within 23cm.6.1.2　Environment in facilities・Set up at the good ventilation.・Don't set up near high temperature equipment (Heater,Transfer,Resistance(large capacity))・In case temperature is over 60℃, set up the fan or air conditioner to down the temperature.・Don't wire near the power code.This product use the frequency of 13.56MHz, please attend to the following. ・Metal Metal has the characteristic, reflect the electric wave. Reception of the equipment becomes worse or there is a possibility of detecting it in the aria where the IC tag is not detected either.・Noise Transceiver, motor, monitor and power source, generate the noise that influences the communication with IC tag. So in case using near the these equipment check the influence before use. 6.1.3　Installation methodTighten an M4 screw with spring washer and flat washer in three places.Do not use the hexagon head screw, so as not to tighten too much.（The tighten torque is 075±0.05 N・m is recommended. ）[7 / 8]6.1 Installation EnviromentUSER MANUALRFID　Reader/Writer [74Eｰ300810-0001-1D]６． InstallationEquipment SideＭ４ Cross Pan head ScrewsＭ４ Spring WasherＭ４ Plain WasherCAUTIONCAUTIONWARNINGFUJITSU TEN LIMITED
・Set up the cable away from the equipment putting out noise.・After it wires, check the connector is firmly set or not.・Attend to cause the large power to the connector・Install the ferrite core in each cable for the noise control. Power Cable: Set up the ferrite core in two places within 100mm from the main body of the power adaptor, and within 100mm from the Reader/Writer's main body.Communication Cable　(RS-232C, USB): Set up the ferrite core within 100mm from the the Reader/Writer's main body.The cable around the ferrite core once so that the ferrite core should not move. Close the ferrite core until you hear it click into place. This Reader/Writer has the serial interface (RS-232C)(USB)RS-232C interface （CN1）PC can control a Reader/Writer by using serial interfaceUSB interface （CN3）PC can control a Reader/Writer by using serial interface[8 / 8]6.2.1　Location of Installing Ferrite Core6.2.2　Method of Installing Ferrite Core7.1 Communications Specifications6.2　Connecting CableUSER MANUALRFID　Reader/Writer [74Eｰ300810-0001-1D]６． Installation7. Communications SpecificationsSerial Communication FormatBit RatesData TransmissionStop BitParity19200 bps8 bit1 bit-Serial Communication FormatBit RatesData TransmissionStop BitParity19200 bps8 bit1 bit-100mm Max. 100mm Max.⇒RFID　　Reader/Writer100mm Max.⇒RFID　　Reader/Writer100mm Max.⇒RFID　　Reader/WriterRS-232CUSBCAUTIONFUJITSU TEN LIMITEDSFT-72SN/TKKSFT-36SN/TKKSFT-59SN/TKKSFT-72SN/TKKTwo TurnsTwo TurnsTwo TurnsTwo Turns

Navigation menu