Feig Electronic MRU200 UHF Reader User Manual M70201 2de ID B
Feig Electronic GmbH UHF Reader M70201 2de ID B
Contents
- 1. Installation Manual
- 2. Users Manual
Users Manual
® OBID i-scan MONTAGE INSTALLATION ID ISC.MRU200 MidRange Reader UHF (deutsch / english) preliminary public (B) 2009-07-24 M70201-2de-ID-B.doc Montage ID ISC.MRU200 DEUTSCH OBID i-scan® FEIG ELECTRONIC GmbH Seite 2 von 54 M70201-2de-ID-B.doc Montage ID ISC.MRU200 DEUTSCH OBID i-scan® ENGLISH deutsche Version ab Seite 4 english version from page 30 FEIG ELECTRONIC GmbH Seite 3 von 54 M70201-2de-ID-B.doc DEUTSCH OBID i-scan® Montage ID ISC.MRU200 Hinweis © Copyright 2007/2008 by FEIG ELECTRONIC GmbH Lange Straße 4 D-35781 Weilburg-Waldhausen Tel.: +49 6471 3109-0 http://www.feig.de Alle früheren Ausgaben verlieren mit dieser Ausgabe ihre Gültigkeit. Die Angaben in diesem Dokument können ohne vorherige Ankündigung geändert werden. Weitergabe sowie Vervielfältigung dieses Dokuments, Verwertung und Mitteilung ihres Inhalts sind nicht gestattet, soweit nicht ausdrücklich zugestanden. Zuwiderhandlung verpflichtet zu Schadenersatz. Alle Rechte für den Fall der Patenterteilung oder Gebrauchsmuster-Eintragung vorbehalten. Die Zusammenstellung der Informationen in diesem Dokument erfolgt nach bestem Wissen und Gewissen. FEIG ELECTRONIC GmbH übernimmt keine Gewährleistung für die Richtigkeit und Vollständigkeit der Angaben in diesem Dokument. Insbesondere kann FEIG ELECTRONIC GmbH nicht für Folgeschäden auf Grund fehlerhafter oder unvollständiger Angaben haftbar gemacht werden. Da sich Fehler, trotz aller Bemühungen nie vollständig vermeiden lassen, sind wir für Hinweise jederzeit dankbar. Die in diesem Dokument gemachten Installationsempfehlungen gehen von günstigsten Rahmenbedingungen aus. FEIG ELECTRONIC GmbH übernimmt keine Gewähr für die einwandfreie Funktion in systemfremden Umgebungen. FEIG ELECTRONIC GmbH übernimmt keine Gewährleistung dafür, dass die in diesem Dokument enthaltenden Informationen frei von fremden Schutzrechten sind. FEIG ELECTRONIC GmbH erteilt mit diesem Dokument keine Lizenzen auf eigene oder fremde Patente oder andere Schutzrechte. ® ® OBID und OBID i-scan ist ein eingetragenes Warenzeichen der FEIG ELECTRONIC GmbH FEIG ELECTRONIC GmbH Seite 4 von 54 M70201-2de-ID-B.doc Montage ID ISC.MRU200 Inhalt Sicherheits- und Warnhinweise - vor Inbetriebnahme unbedingt lesen Leistungsmerkmale 2.1 Verfügbare Readertypen.............................................................................................8 2.2 Lieferumfang ...............................................................................................................8 Montage 3.1 Kabelverschraubungen ............................................................................................10 3.2 Dichtverschlüsse ......................................................................................................10 3.3 Deckelhalter...............................................................................................................11 3.4 Designblenden ..........................................................................................................11 Anschlussklemmen und -buchsen 12 4.1 Versorgungsspannung .............................................................................................13 4.2 Antennenanschlüsse ................................................................................................14 4.3 Schnittstellen ............................................................................................................15 4.3.1 RS232-Schnittstelle.....................................................................................................15 4.3.2 RS485- / RS422-Schnittstelle (ID ISC.MRU200-USB).................................................16 4.3.3 Ethernet-Schnittstelle (ID ISC.MRU200-E) ..................................................................17 4.3.4 USB-Schnittstelle (ID ISC.MRU200-USB) ...................................................................18 4.4 Eingänge....................................................................................................................18 4.5 Ausgänge...................................................................................................................20 4.5.1 Optokoppler ................................................................................................................20 4.5.2 Relais..........................................................................................................................21 Bedien- und Anzeigeelemente 22 5.1 LEDs...........................................................................................................................22 5.2 T1: Reset-Taster ........................................................................................................22 FEIG ELECTRONIC GmbH Seite 5 von 54 M70201-2de-ID-B.doc DEUTSCH OBID i-scan® DEUTSCH OBID i-scan® Montage ID ISC.MRU200 5.3 J1-J8: Schnittstellenkonfiguration...........................................................................23 5.4 X62: Bootloader Modus ............................................................................................24 Technische Daten 6.1 25 Zulassung ..................................................................................................................27 6.1.1 Europa (CE) ................................................................................................................27 6.1.2 USA (FCC)..................................................................................................................27 6.1.3 USA und Kanada (UL) ................................................................................................28 FEIG ELECTRONIC GmbH Seite 6 von 54 M70201-2de-ID-B.doc Montage ID ISC.MRU200 Sicherheits- und Warnhinweise - vor Inbetriebnahme unbedingt lesen • Das Gerät darf nur für den vom Hersteller vorgesehenen Zweck verwendet werden. • Beim Aufstellen des Gerätes im Geltungsbereich der FCC 47 CFR Part 15 ist ein Mindestabstand von 20 cm zwischen Antenne und menschlichem Körper zu gewährleisten. • Die Bedienungsanleitung ist zugriffsfähig aufzubewahren und jedem Benutzer auszuhändigen. • Unzulässige Veränderungen und die Verwendung von Ersatzteilen und Zusatzeinrichtungen, die nicht vom Hersteller des Gerätes verkauft oder empfohlen werden, können Brände, elektrische Schläge und Verletzungen verursachen. Solche Maßnahmen führen daher zu einem Ausschluss der Haftung und der Hersteller übernimmt keine Gewährleistung. • Für das Gerät gelten die Gewährleistungsbestimmungen des Herstellers in der zum Zeitpunkt des Kaufs gültigen Fassung. Für eine ungeeignete, falsche manuelle oder automatische Einstellung von Parametern für ein Gerät bzw. ungeeignete Verwendung eines Gerätes wird keine Haftung übernommen. • Reparaturen dürfen nur vom Hersteller durchgeführt werden. • Anschluss-, Inbetriebnahme-, Wartungs-, und sonstige Arbeiten am Gerät dürfen nur von Elektrofachkräften mit einschlägiger Ausbildung erfolgen. • Alle Arbeiten am Gerät und dessen Aufstellung müssen in Übereinstimmung mit den nationalen elektrischen Bestimmungen und den örtlichen Vorschriften durchgeführt werden. • Beim Arbeiten an dem Gerät müssen die jeweils gültigen Sicherheitsvorschriften beachtet werden. Es wird vorausgesetzt, dass zwischen Leser und Antenne ein Kabel mit einer Mindestdämpfung von 0,3 dB verwendet wird. Für die Zulassungsprüfungen wurde der Kabeltyp H 155 mit 2 m Länge verwendet. Besonderer Hinweis für Träger von Herzschrittmachern: Obwohl dieses Gerät die zulässigen Grenzwerte für elektromagnetische Felder nicht überschreitet, sollten Sie einen Mindestabstand von 25 cm zwischen dem Gerät und Ihrem Herzschrittmacher einhalten und sich nicht für längere Zeit in unmittelbarer Nähe des Geräts bzw. der Antenne aufhalten. FEIG ELECTRONIC GmbH Seite 7 von 54 M70201-2de-ID-B.doc DEUTSCH OBID i-scan® DEUTSCH OBID i-scan® Montage ID ISC.MRU200 Leistungsmerkmale Der Reader ist für das Lesen von passiven Datenträgern, sogenannten „Smart Labels“, mit einer Betriebsfrequenz im UHF Bereich entwickelt. 2.1 Verfügbare Readertypen Folgende Readertypen sind z.Z. verfügbar: Tabelle 2-1: Verfügbare Readertypen Readertyp Beschreibung ID ISC.MRU200-USB-EU Reader mit USB-Schnittstelle für Europa ID ISC.MRU200-E-EU Reader mit Ethernet-Schnittstelle für Europa ID ISC.MRU200-USB-FCC Reader mit USB-Schnittstelle für USA ID ISC.MRU200-E-FCC Reader mit Ethernet-Schnittstelle für USA 2.2 Lieferumfang Folgende Komponenten sind im Lieferumfang enthalten: 1 x Reader ID ISC.MRU200 8 x Kurzschlussbrücke (Jumper) 2 x Dichtverschluss M16 1 x Dichtverschluss M12 1 x Dichtverschluss-Reduzierstück 2 x Designblenden aufsteckbar 2 x Integrierte Deckelhalter FEIG ELECTRONIC GmbH Seite 8 von 54 M70201-2de-ID-B.doc 3 Montage ID ISC.MRU200 Montage Der Reader ist für die Montage auf Wänden konzipiert. Zur Wandmontage befinden sich vier im Gehäuse vorgesehene Löcher (d=7mm, Maß 60mmx182mm). Dazu muss das Gehäuse nicht geöffnet werden. (siehe Bild 3-1). Die Größe und Art der Schrauben und Befestigungsdübel hängt stark von der Festigkeit des Untergrundes ab. Die Dübel und Schrauben sollten mindestens eine zulässige Last von 1.5 kN für alle Belastungsrichtungen aushalten (Untergrund Stahl z.B. Zylinderschraube M5 Stahl verzinkt DIN 84 / ISO 1207, Festigkeitskasse 8.8 oder Beton, Stein z.B. Kunststoffdübel 6mm mit Holzschraube DIN96 d=4mm). Der maximale Schraubenkopfdurchmesser beträgt 8,5 mm 200 (7.87) 110 (4.33) 60 (2.36) 182 (7.16) Bild 3-1: Gehäuse ID ISC.MRU200 (alle Maße in mm (inch)) FEIG ELECTRONIC GmbH Seite 9 von 54 M70201-2de-ID-B.doc DEUTSCH OBID i-scan® DEUTSCH OBID i-scan® 3.1 Montage ID ISC.MRU200 Kabelverschraubungen Die einzelnen Kabelverschraubungen sind in Tabelle 3-1 aufgelistet: Tabelle 3-1: Kabelverschraubungen ID ISC.MRU200 KabelVerschraubung Größe Klemmbereich (in mm) M 16 4,5...10 Anschlusskabel Antenne 1 M 16 4,5...10 Anschlusskabel Antenne 2 M 16 4,5...10 Eingänge / Relais / Ausgänge M 12 3,5...7 Schnittstelle (seriell) M 12 3,5...7 Spannungsversorgung M 25 9...17 Ethernet Interface (nur -E) / USB (nur -A) 3.2 Beschreibung Dichtverschlüsse Mit denen im Zubehör beigelegten Dichtverschlüssen können nicht benutzte Kabelverschraubungen verschlossen werden. Nur dann wird auch die Schutzart IP54 erreicht. Das beigelegte Dichtring-Reduzierstück ist für die Netzwerkanbindung bzw. das USBAnschlusskabel vorgesehen. Das aufgeschlitzte Reduzierstück wird über die Netzwerkleitung bzw. das USB-Anschlusskabel gelegt und anschließend in der Kabelverschraubung fixiert. Bild 3-2: Netzwerkanbindung mit Dichtring-Reduzierstück FEIG ELECTRONIC GmbH Seite 10 von 54 M70201-2de-ID-B.doc 3.3 Montage ID ISC.MRU200 Deckelhalter Mit den beiden Deckelhaltern kann der Deckel an dem Gehäuse fixiert werden. Die Deckelhalter werden in die dafür vorgesehenen Öffnungen eingesteckt. Bild 3-3: Deckelhalter 3.4 Designblenden Die Designblenden werden nach der Montage des Readers aufgesteckt. Die Nut an der Längsseite der Blende dient zur Demontage der Blende. Mit einem geeigneten Schraubendreher kann die Blende entfernt werden. Bild 3-4: Designblende FEIG ELECTRONIC GmbH Seite 11 von 54 M70201-2de-ID-B.doc DEUTSCH OBID i-scan® 4 Montage ID ISC.MRU200 Anschlussklemmen und -buchsen In Bild 4-1 und Bild 4-2 sind alle Anschlussklemmen und -buchsen, sowie die Bedien- und Anzeigeelemente für die Readertypen -USB bzw. -E dargestellt. X1 VDC GND TxD RxD GND X8 J8 Z+ Y- B+ A- GND J1 X2 X62 OUT2 OUT1 X3 IN2 IN1 X4 ANT2 N0 NC COM X5 ANT1 T1 V4 V3 V2 K1 V1 X6 DEUTSCH OBID i-scan® Bild 4-1: Anschlussklemmen und -buchsen (Typ -A) FEIG ELECTRONIC GmbH Seite 12 von 54 M70201-2de-ID-B.doc OBID i-scan® ID ISC.MRU200 DEUTSCH Montage X1 GND VDC GND X7 Bild 4-2: Anschlussklemmen und -buchsen (Typ -E) 4.1 Versorgungsspannung Die Versorgungsspannung von 12...24 VDC wird an der Klemme X1 angeschlossen. Die Zuleitungslänge zwischen Netzteil und Reader-Modul darf 3 m nicht überschreiten. Tabelle 4-1: Pinbelegung Versorgungsspannung Klemme X1 / Pin 1 X1 / Pin 2 Kurzzeichen VDC GND Beschreibung VDC – Versorgungsspannung (+) Ground – Versorgungsspannung (-) GND VDC X1 Bild 4-3: Anschluss der Versorgungsspannung Die Ausgangsleistung des Netzteils sollte min. 15 W betragen. Bei allen Installation nach UL 60950 bzw. EN 60950 gilt: • Das Gerät muss mit einem „Listed NEC Class 2/LPS“ Netzteil versorgt werden • Bei Anschluss der Geräte mit flexiblen Leitungen sind im besondern die Vorschriften nach NEC Artikel 400.7 (8) und Artikel 400.8 (1) – (7) Anzuwenden. Hinweis: Eine Verpolung der Versorgungsspannung kann zur Zerstörung des Gerätes führen. FEIG ELECTRONIC GmbH Seite 13 von 54 M70201-2de-ID-B.doc DEUTSCH OBID i-scan® 4.2 Montage ID ISC.MRU200 Antennenanschlüsse Der Anschluss der Antennen erfolgt über die SMA-Buchsen ANT1 und ANT2. Das SWR der angeschlossen Antennen mit Kabel darf 1,5:1 nicht überschreiten. Tabelle 4-2: Antennenanschluss Anschluss ANT1, ANT2 Beschreibung SMA-Buchse für Antennenanschluss (Eingangsimpedanz 50 Ω) ANT1 ANT2 Bild 4-4: Antennenanschluss Hinweis: Das maximale Anzugsdrehmoment der SMA-Buchsen beträgt 0,45 Nm. FEIG ELECTRONIC GmbH Seite 14 von 54 M70201-2de-ID-B.doc OBID i-scan® ID ISC.MRU200 DEUTSCH 4.3 Montage Schnittstellen 4.3.1 RS232-Schnittstelle Der Anschluss der RS232-Schnittstelle erfolgt über X2. Die Übertragungsparameter können per Softwareprotokoll konfiguriert werden. Tabelle 4-3: Pinbelegung RS232-Schnittstelle Klemme Kurzzeichen Beschreibung X2 / Pin 1 GND RS232 – GND X2 / Pin 2 RxD RS232 – RxD X2 / Pin 3 TxD RS232 – TxD PC X2 / Pin 1 (GND) Pin 5 X2 / Pin 2 (RxD) Pin 3 X2 / Pin 3 (TxD) Pin 2 X2 Reader TxD RxD GND 9-pol. DUB-D-Buchse PC Bild 4-5: Verdrahtungsbeispiel für den Anschluss der RS232-Schnittstelle FEIG ELECTRONIC GmbH Seite 15 von 54 M70201-2de-ID-B.doc Montage ID ISC.MRU200 4.3.2 RS485- / RS422-Schnittstelle (ID ISC.MRU200-USB) Die zweite asynchrone Schnittstelle kann als RS485 oder RS422 konfiguriert werden (siehe 5.3 J1J8: Schnittstellenkonfiguration ). Der Anschluss der RS485- bzw. RS422-Schnittstelle erfolgt über X3. Tabelle 4-4 zeigt die Pinnbelegung für die entsprechende Schnittstelle: Tabelle 4-4: Pinbelegung RS485-/RS422-Schnittstelle Klemme Kurzzeichen Beschreibung X3 / Pin 1 GND RS485/RS422 – GND X3 / Pin 2 A- RS485/RS422 – (A -) X3 / Pin 3 B+ RS485/RS422 – (B +) X3 / Pin 4 Y- RS422 – (Y -) X3 / Pin 5 Z+ RS422 – (Z +) X3 DEUTSCH OBID i-scan® Z+ Y- B+ A- GND Bild 4-6: Anschlussbelegung der RS485-/RS422-Schnittstelle FEIG ELECTRONIC GmbH Seite 16 von 54 M70201-2de-ID-B.doc Montage ID ISC.MRU200 4.3.3 Ethernet-Schnittstelle (ID ISC.MRU200-E) Der Reader verfügt über eine integrierte 10/100 base-T Netzwerkschnittstelle mit RJ-45- Anschluss. Der Anschluss erfolgt über X7. Bei einer strukturierten Verkabelung sollte Kabel der Kategorie 5 verwendet werden. Dies garantiert einen problemlosen Betrieb bei 10 Mbps oder 100 Mbps. Tabelle 4-5: Pinbelegung Ethernet-Schnittstelle Klemme Kurzzeichen Beschreibung X7 / Pin 1 TX+ Transmit Data + X7 / Pin 2 TX- Transmit Data - X7 / Pin 3 RX+ Receive Data + X7 / Pin 4 VETH+ n.c. X7 / Pin 5 VETH+ n.c. X7 / Pin 6 RX- X7 / Pin 7 VETH- n.c. X7 / Pin 8 VETH- n.c. Receive Data - Vorraussetzung für den Einsatz des TCP/IP-Protokolls ist, dass jedes Gerät am Netzwerk über eine eigene IP-Adresse verfügt. Alle Reader verfügen über eine werksseitig voreingestellte IP-Adresse. Tabelle 4-6: Standardkonfiguration der Ethernet-Schnittstelle Netzwerk Adresse IP-Adresse 192.168.10.10 Subnet-Mask 255.255.255.0 Port 10001 Hinweis: Die Reader müssen nacheinander ans Netzwerk angeschlossen und konfiguriert werden. Jede IP-Adresse darf nur einmal im Netzwerk vertreten sein. Alternativ kann die Einstellung über die asynchrone Schnittstelle erfolgen. FEIG ELECTRONIC GmbH Seite 17 von 54 M70201-2de-ID-B.doc DEUTSCH OBID i-scan® DEUTSCH OBID i-scan® Montage ID ISC.MRU200 4.3.4 USB-Schnittstelle (ID ISC.MRU200-USB) Der Anschluss der USB-Schnittstelle erfolgt über Buchse X8. Die Belegung ist genormt. Die Datenrate des Readers ist auf 12 Mbit beschränkt (USB Full Speed). Es kann ein Standard-USB-Kabel verwendet werden. Hinweis: Die maximale Länge des USB-Kabels darf 5 m betragen. Längere Kabel sind nicht erlaubt. 4.4 Eingänge Die Optokopplereingänge an Klemmleiste X5 sind galvanisch von der Reader-Elektronik getrennt und müssen daher mit einer externen Gleichspannung versorgt werden. Die Eingangs-LEDs der Optokoppler sind intern mit einem Serienwiderstand Rint von 500 Ω beschaltet. Tabelle 4-7: Pinbelegung Optokopplereingänge Klemme Kurzzeichen Beschreibung X5 / Pin 1 IN1+ + Eingang 1 X5 / Pin 2 IN1- - Eingang 1 X5 / Pin 3 IN2+ + Eingang 2 X5 / Pin 4 IN2- - Eingang 2 X5 Rint IN2 Rint IN1 Rext Uext Rext Uext Bild 4-7: Interne und mögliche externe Beschaltung der Optokopplereingänge Bei Versorgungsspannungen größer 10 V muss der Eingangsstrom durch einen weiteren externen Vorwiderstand (siehe Tabelle 4-8) auf max. 20 mA begrenzt werden. FEIG ELECTRONIC GmbH Seite 18 von 54 M70201-2de-ID-B.doc OBID i-scan® Montage ID ISC.MRU200 Externe Spannung Uext Benötigter externer Vorwiderstand Rext 5...10 V --- 11...15 V 270 Ω 16...20 V 560 Ω 21...24 V 820 Ω DEUTSCH Tabelle 4-8: Externe Vorwiderstände Hinweise: • Die Eingänge sind für eine maximale Eingangsspannung von 24 VDC und einen Eingangsstrom von maximal 20 mA ausgelegt. • Verpolung oder Überlastung der Eingänge führt zu deren Zerstörung. • Die Versorgungsspannung des Readers darf nicht zur Ansteuerung der Eingänge verwendet werden, da es ansonsten durch zusätzlich eingestrahlte Störungen zu Einbußen in der Lesereichweite kommen kann. FEIG ELECTRONIC GmbH Seite 19 von 54 M70201-2de-ID-B.doc DEUTSCH OBID i-scan® 4.5 Montage ID ISC.MRU200 Ausgänge 4.5.1 Optokoppler Die Transistoranschlüsse, Kollektor und Emitter, der beiden Optokopplerausgänge sind von der Reader-Elektronik galvanisch getrennt und ohne interne Zusatzbeschaltung an Klemme X4 nach außen geführt. Die Ausgänge müssen daher mit einer externen Spannung betrieben werden. Tabelle 4-9: Pinbelegung Optokopplerausgänge Klemme Kurzzeichen Beschreibung X4 / Pin 1 O1-C Kollektor – Ausgang 1 X4 / Pin 2 O1-E Emitter – Ausgang 1 X4 / Pin 3 O2-C Kollektor – Ausgang 2 X4 / Pin 4 O2-E Emitter – Ausgang 2 X4 OUT2 OUT1 Bild 4-8: Interne und mögliche externe Beschaltung der Optokopplerausgänge Hinweise: • Die Ausgänge sind für max. 24 VDC / 30 mA ausgelegt. • Verpolung oder Überlastung der Ausgänge führt zu deren Zerstörung. • Die Ausgänge sind nur zum Schalten ohmscher Lasten vorgesehen. FEIG ELECTRONIC GmbH Seite 20 von 54 M70201-2de-ID-B.doc OBID i-scan® ID ISC.MRU200 DEUTSCH Montage 4.5.2 Relais Als Relaisausgang steht an X6 ein Wechsler zur Verfügung. Tabelle 4-10: Pinbelegung Relaisausgang Klemme Kurzzeichen Beschreibung X6 / Pin 1 COM X6 / Pin 2 NC Öffner X6 / Pin 3 NO Schließer Arbeitskontakt X6 N0 NC Uext COM Bild 4-9: Interne und mögliche externe Beschaltung des Relaisausgangs Hinweise: • Der Relaisausgang ist für max. 24 VDC / 2 A ausgelegt. • Der Relaisausgang ist nur zum Schalten ohm´scher Lasten vorgesehen. Im Falle einer induktiven Last sind die Relaiskontakte durch eine externe Schutzbeschaltung zu schützen. FEIG ELECTRONIC GmbH Seite 21 von 54 M70201-2de-ID-B.doc DEUTSCH OBID i-scan® 5.1 Montage ID ISC.MRU200 Bedien- und Anzeigeelemente LEDs In Tabelle 5-1 sind die Konfigurationen der einzelnen LEDs aufgelistet: Tabelle 5-1: Konfiguration der LEDs Kurzzeichen Beschreibung "RUN-LED 1" LED V1 (grün) Signalisiert den ordnungsgemäßen Ablauf der internen Reader-Software Diagnose 1: RF-Kommunikation / EEPROM-Status LED V2 (blau) Signalisiert durch ein kurzes Blinken die fehlerfreie Kommunikation mit einem Transponder auf der RF-Schnittstelle Blinkt abwechselnd mit V1 nach dem Reset im Anschluss an ein Software-Update Blinkt abwechselnd mit V1 falls nach einem Reset ein Datenfehler beim Lesen der Parameter auftrat Diagnose 2: Host-Kommunikation LED V3 (gelb) Signalisiert durch ein kurzes Blinken das Senden eines Protokolls an den Host Diagnose 3: RF-Warnung LED V4 (rot) 5.2 Leuchtet bei einem Fehler im RF-Teil des Readers. Der Fehlertyp kann per Software über die Schnittstellen ausgelesen werden T1: Reset-Taster Durch Betätigen des Tasters T1 wird am Reader ein Reset durchgeführt. FEIG ELECTRONIC GmbH Seite 22 von 54 M70201-2de-ID-B.doc 5.3 Montage ID ISC.MRU200 J1-J8: Schnittstellenkonfiguration Über die Jumper J7 – J8 kann die asynchrone Schnittstelle als RS485- oder RS422-Schnittstelle konfiguriert werden. Tabelle 5-2: Konfiguration der RS485-/RS422-Schnitstelle Jumper RS485 RS422 J7 geschlossen offen J8 geschlossen offen Es können die eventuell benötigten Abschlusswiderstände mit den Jumpern J1 bis J6 zugeschaltet werden. Tabelle 5-3: Abschlusswiderstände der RS485/RS422 Jumper Geschlossen offen J1 Pull-Up an RS4xx -B ohne Pull-Up an RS4xx -B J2 Pull-Down an RS4xx -A ohne Pull-Down an RS4xx -A J5 Abschlusswiderstand RS4xx -A ⇔ RS4xx -B ohne Abschlusswiderstand RS485 -A ⇔ RS485 -B J3 Pull-Up an RS422 -Z ohne Pull-Up an RS422 -Z J4 Pull-Down an RS422 -Y ohne Pull-Down an RS422 -Y J6 Abschlusswiderstand RS422 -Y ⇔ RS422 -Z ohne Abschlusswiderstand RS422 -Y ⇔ RS422 -Z 500 Ohm J1 J8 J1 500 RS422 Z+ 120 Ohm J7 500 J3 RS485 + 120 J6 RS422 YRS422 B+ J5 J2 RS485 J4 500 Ohm Bild 5-1: Jumper der RS485-Schnittstelle FEIG ELECTRONIC GmbH 120 J5 RS422 A500 J2 500 Bild 5-2: Jumper der RS422-Schnittstelle Seite 23 von 54 M70201-2de-ID-B.doc DEUTSCH OBID i-scan® DEUTSCH OBID i-scan® 5.4 Montage ID ISC.MRU200 X62: Bootloader Modus Die Stiftleiste X62 kann mit einem Jumper (Rastermaß 2,0 mm) kurzgeschlossen werden. In Tabelle 5-4 ist die Funktion der Stiftleiste X62 beschrieben. Tabelle 5-4: Stiftleiste X62 X60 Beschreibung offen keine Auswirkung kurzgeschlossen nach Betätigen des Tasters T1 wird der Reader in den Bootloader Modus versetzt. FEIG ELECTRONIC GmbH Seite 24 von 54 M70201-2de-ID-B.doc 6 Montage ID ISC.MRU200 Technische Daten Mechanische Daten • Gehäuse Aluminium Druckguss, pulverbeschichtet, verschließbarer Klappdeckel • Abmessungen (B x H x T) 200 x 110 x 60 mm³ • Gewicht 1,1 kg • Schutzart IP 54 • Farbe RAL 7040 (ähnlich Fenstergrau) Elektrische Daten • Spannungsversorgung 12...24 VDC ±5% Noise Ripple : max. 150 mV • Leistungsaufnahme max. 15 VA • Betriebsfrequenz 865,6...867,6 MHz (EN 302 208) 902...928 MHz (FCC CFR 47 Part 15.247) • Sendeleistung 100...300 mW (100 mW Step – Software) • Modulationsgrad 20...40% und 100% (per Software einstellbar) • Empfänger Datenraten 40 kbps, 64 kbps, 80 kbps • Antennenanschlüsse - 2 x gemultiplext 2 x SMA Buchse (50 Ω) • Ausgänge: - 2 Optokoppler - 1 Relais (1 x Wechsler) 24 VDC 24 VDC / 30 mA (galvanisch getrennt) /2A • Eingänge - 1 Optokoppler • Schnittstellen FEIG ELECTRONIC GmbH max. 24 VDC / 20 mA - RS232 - RS485 / RS422 (wahlweise einstellbar) - Ethernet (TCP/IP) (ID ISC.MRU200-E) - USB (ID ISC.MRU200-A) Seite 25 von 54 M70201-2de-ID-B.doc DEUTSCH OBID i-scan® DEUTSCH OBID i-scan® Montage ID ISC.MRU200 • Protokoll Modi - FEIG ISO Host - Buffer Reader Mode (Data Filtering and buffering) - Scan Mode • Unterstützte Transponder - EPC class 1 Gen 2 - 18000-6-B (UpgradeCode notwendig) • Signalgeber optisch 4 LEDs zur Diagnose des Betriebszustandes • Multi-Reader-Betrieb Synchronisation der Luftprotokolle durch Verwendung der Reader Synchronisation Umgebungsbedingungen • Temperaturbereich - Betrieb - Lagerung • Vibration • Schock -25...+55°C -25...+85°C EN60068-2-6 10...150 Hz : 0,075 mm / 1 g EN60068-2-27 Beschleunigung : 30 g Angewendete Normen • Zulassung Funk - Europa - USA • EMV EN 302 208 FCC 47 CFR Part 15 EN 301 489 • Sicherheit – Niederspannung - Human Exposure FEIG ELECTRONIC GmbH EN 60950 UL 60950-1 EN 50364 Seite 26 von 54 M70201-2de-ID-B.doc 6.1 Montage ID ISC.MRU200 DEUTSCH OBID i-scan® Zulassung 6.1.1 Europa (CE) Die Funkanlage entspricht, bei bestimmungsgemäßer Verwendung den grundlegenden Anforderungen des Artikels 3 und den übrigen einschlägigen Bestimmungen der R&TTE Richtlinie 1999/5/EG vom März 99. Equipment Classification gemäß ETSI EN 302 208 und ETSI EN 301 489: Class 2 6.1.2 USA (FCC) FCC ID: PJMMRU200 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTICE: Changes or modifications made to this equipment not expressly approved by FEIG ELECTRONIC GmbH may void the FCC authorization to operate this equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FEIG ELECTRONIC GmbH Seite 27 von 54 M70201-2de-ID-B.doc DEUTSCH OBID i-scan® Montage ID ISC.MRU200 6.1.3 USA und Kanada (UL) NOTE: To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that permitted for successful communication. This device has been designed to operate with the antennas listed below, and having a maximum gain of 10.5 dBic. Antennas not included in this list or having a gain greater than 10.5 dBic are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Lists of Antennas: ID.ISC.ANT.U250/250-FCC ID.ISC.ANT.U170/170-FCC ID ISC.ANT.U270/270-FCC ID ISC.ANT.U600/270-FCC FEIG ELECTRONIC GmbH Seite 28 von 54 M70201-2de-ID-B.doc OBID i-scan® Installation ID ISC.MRU200 ENGLISH Note © Copyright 2007/2008 by FEIG ELECTRONIC GmbH Lange Strasse 4 D-35781 Weilburg-Waldhausen Tel.: +49 6471 3109-0 http://www.feig.de With the edition of this document, all previous editions become void. Indications made in this manual may be changed without previous notice. Copying of this document, and giving it to others and the use or communication of the contents thereof are forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design. Composition of the information in this manual has been done to the best of our knowledge. FEIG ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since, despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips. The installation instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC GmbH does not give any guarantee promise for perfect function in cross environments. FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this manual and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH does not convey any license under its patent rights nor the rights of others. ® ® OBID and OBID i-scan are registered trademarks of FEIG ELECTRONIC GmbH. FEIG ELECTRONIC GmbH Page 30 of 54 M70201-2de-ID-B.doc OBID i-scan® Installation ID ISC.MRU200 Safety Instructions / Warning - Read before start-up ! 33 Features of the Reader Family ID ISC.MRU200 34 2.1 Available Reader Types ............................................................................................34 2.2 Scope of delivery ......................................................................................................34 Installation 35 3.1 Cable Glands .............................................................................................................36 3.2 Seal Caps...................................................................................................................36 3.3 Cover stays................................................................................................................37 3.4 Decorative Covers.....................................................................................................37 Terminals and Jacks 38 4.1 Supply Voltage ..........................................................................................................39 4.2 Antenna Connections ...............................................................................................40 4.3 Interfaces ...................................................................................................................41 4.3.1 RS232 Interface ..........................................................................................................41 4.3.2 RS485 / RS422 Interface (ID ISC.MRU200-USB) .......................................................42 4.3.3 Ethernet Interface (ID ISC.MRU200-E) .......................................................................43 4.3.4 USB Interface (ID ISC.MRU200-USB).........................................................................44 4.4 Inputs .........................................................................................................................44 4.5 Outputs ......................................................................................................................46 4.5.1 Optocouplers...............................................................................................................46 4.5.2 Relay...........................................................................................................................47 Operating and Display Elements 48 5.1 LEDs...........................................................................................................................48 5.2 Reset Button..............................................................................................................48 FEIG ELECTRONIC GmbH Page 31 of 54 M70201-2de-ID-B.doc ENGLISH Contents OBID i-scan® ID ISC.MRU200 5.3 J1-J8: Interface configuration ..................................................................................49 5.4 X62: Boot Loader Mode ............................................................................................50 Technical Data 6.1 ENGLISH Installation 51 Approval ....................................................................................................................53 6.1.1 Europe (CE) ................................................................................................................53 6.1.2 USA (FCC)..................................................................................................................53 6.1.3 USA and Canada (UL) ................................................................................................54 FEIG ELECTRONIC GmbH Page 32 of 54 M70201-2de-ID-B.doc OBID i-scan® ID ISC.MRU200 Safety Instructions / Warning - Read before start-up ! • The device may only be used for the intended purpose designed by for the manufacturer. • When installing the device in areas covered under FCC 47 CFR Part 15 a minimum separation of 20 cm (8 inch) between antenna and the human body must be maintained. • The operation manual should be conveniently kept available at all times for each user. • Unauthorized changes and the use of spare parts and additional devices which have not been sold or recommended by the manufacturer may cause fire, electric shocks or injuries. Such unauthorized measures shall exclude any liability by the manufacturer. • The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid for the device. The manufacturer shall not be held legally responsible for inaccuracies, errors, or omissions in the manual or automatically set parameters for a device or for an incorrect application of a device. • Repairs may only be executed by the manufacturer. • Installation, operation, and maintenance procedures should only be carried out by qualified personnel. • Use of the device and its installation must be in accordance with national legal requirements and local electrical codes . • When working on devices the valid safety regulations must be observed. It will provided that between integrator and antenna a cable with a minimum attenuation of 0.3 dB is used. For the approval tests the type of cable H 155 with 2 m length was used. Special advice for wearers of cardiac pacemakers: Although this device doesn't exceed the valid limits for electromagnetic fields you should keep a minimum distance of 25 cm (10 inch) between the device and your cardiac pacemaker and not stay in the immediate proximity of the device’s antenna for any length of time. FEIG ELECTRONIC GmbH Page 33 of 54 M70201-2de-ID-B.doc ENGLISH Installation OBID i-scan® Installation ID ISC.MRU200 Features of the Reader Family ID ISC.MRU200 ENGLISH The Reader has been developed for reading passive data carriers, so-called „Smart Labels“, using an operating frequency in the UHF range. 2.1 Available Reader Types The following Readers are currently available: Table 2-1: Available Reader types Reader type Description ID ISC.MRU200-USB-EU Reader with USB Interface for Europe ID ISC.MRU200-E-EU Reader with Ethernet Interface for Europe ID ISC.MRU200-USB-FCC Reader with USB Interface for USA ID ISC.MRU200-E-FCC Reader with Ethernet-Interface for USA 2.2 Scope of delivery The following components are included in the scope of delivery: 1 x Reader ID ISC.MRU200 8 x jumper 2 x seal cap M16 1 x seal cap M12 1 x seal cap - reducer 2 x decorative cover, clip-on 2 x integrated cover stays FEIG ELECTRONIC GmbH Page 34 of 54 M70201-2de-ID-B.doc OBID i-scan® ID ISC.MRU200 Installation The Reader is designed for wall mount. Four Holes are provided in the housing for wall attachment (d=7mm (.27”), measurement 60x182mm). The housing does not need to be opened for installation on a wall (see Fig. 3-1). The size and type of the screw anchors depends considerably on the strength of the wall. The anchors should be capable of withstanding a permissible load of at least 1.5 kN per anchor for all load directions (Undersurface steal e.g. cylinder head screw M5 steal zinc coated DIN 84 / ISO 1207, property class 8.8 or concrete, stone e.g. plastic anchor 6mm with wood screw DIN96 d=4mm). The maximum size of the screw head is 8.5mm (0.33”) 200 (7.87) 110 (4.33) 60 (2.36) 182 (7.16) Fig. 3-1: Housing ID ISC.MRU200 (all dimensions in mm (inch)) FEIG ELECTRONIC GmbH Page 35 of 54 M70201-2de-ID-B.doc ENGLISH Installation OBID i-scan® 3.1 Installation ID ISC.MRU200 Cable Glands The different cable glands are shown in Table 3-1. Table 3-1: ID ISC.MRU200 cable glands Size Clamping Range in mm (inch) M 16 4,5...10 (0.18...0.39) Antenna Cable 1 M 16 4,5...10 (0.18...0.39) Antenna Cable 2 M 16 4,5...10 (0.18...0.39) Inputs / Relay / Outputs M 12 3,5...7 (0.14...0.28) Interface (serial) M 12 3,5...7 (0.14...0.28) Supply voltage M 25 9...17 (0.35...0.67) Ethernet Interface (Model –E only) USB Interface (Model –USB only) ENGLISH Cable gland 3.2 Description Seal Caps The seal caps included in the scope of delivery can be used to close off unused cable fittings. This is necessary for reaching the IP54 class. The reducing ring provided is intended for the network connection. The slotted reducer is placed over the network cable and then fixed in place in the cable gland. Fig. 3-2: network connection with slotted reducer FEIG ELECTRONIC GmbH Page 36 of 54 M70201-2de-ID-B.doc OBID i-scan® 3.3 Installation ID ISC.MRU200 Cover stays ENGLISH The two cover stays can be used to attach the cover to the housing. The cover stays are inserted into the openings provided for this purpose. Fig. 3-3: Cover stay 3.4 Decorative Covers The decorative covers are attached after installing the Reader. The slot on the long side of the cover is used for disassembling the cover. Use a screwdriver to remove the cover. Fig. 3-4: Decorative cover FEIG ELECTRONIC GmbH Page 37 of 54 M70201-2de-ID-B.doc OBID i-scan® Installation ID ISC.MRU200 Terminals and Jacks Fig. 4-1 and Fig. 4-2 show terminals, jacks and operating elements of reader type -USB respectively reader type -E. TxD RxD GND X8 J8 Z+ Y- B+ A- GND J1 X2 X62 OUT2 OUT1 X3 IN2 IN1 X4 ANT2 N0 NC COM X5 ANT1 T1 V4 V3 V2 K1 V1 X6 ENGLISH X1 VDC GND Fig. 4-1: Terminals, jacks and operating elements of Type -USB FEIG ELECTRONIC GmbH Page 38 of 54 M70201-2de-ID-B.doc OBID i-scan® Installation ID ISC.MRU200 X1 GND VDC GND 4.1 Supply Voltage Connect the 12...24 VDC supply voltage to Terminal X1. The cable length between the power supply and the Reader module must not exceed 3m (118 inch). Table 4-1: Supply voltage pin assignments Terminal X1 / Pin 1 X1 / Pin 2 Abbreviation VDC GND Description Vcc – supply voltage (+) Ground – supply voltage (-) GND VDC X1 Fig. 4-3: Connecting the supply voltage The output power of the power supply should be at least 15 W. At all installation according to UL 60950 or EN 60950, • this unit has to be supplied by a Listed NEC Class 2/LPS supply, only. • by use of flexible cords, the NEC rules according article 400.7 (8) and 400.8 (1)-(7) must be applied. Note: Reversing the polarity of the supply voltage may destroy the unit. FEIG ELECTRONIC GmbH Page 39 of 54 M70201-2de-ID-B.doc ENGLISH X7 Fig. 4-2: Terminals, jacks and operating elements of Type -E OBID i-scan® 4.2 Installation ID ISC.MRU200 Antenna Connections The external antennas are connected to the SMA jacks ANT1 and ANT2. The SWR of the connected antennas with the cables should not be worse than 1.5:1. ENGLISH Table 4-2: Antenna Connections ANT1 and ANT2 Connections ANT1, ANT2 Description SMA jacks for antenna connections (input impedance 50 Ω) ANT1 ANT2 Fig. 4-4: Antenna Connections ANT1 and ANT2 Note: The maximum tightening torque of the SMA sockets is 0,45 Nm (4.0 lbf in). FEIG ELECTRONIC GmbH Page 40 of 54 M70201-2de-ID-B.doc OBID i-scan® 4.3 Installation ID ISC.MRU200 Interfaces The RS232 interface is connected on X2. The transmission parameters can be configured by means of software protocol. Table 4-3: RS232 interface pinouts Abbreviation X2 / Pin 1 GND RS232 – GND X2 / Pin 2 RxD RS232 – RxD X2 / Pin 3 TxD RS232 – TxD X2 Terminal Description Reader PC X2 / Pin 1 (GND) Pin 5 X2 / Pin 2 (RxD) Pin 3 X2 / Pin 3 (TxD) Pin 2 TxD RxD GND 9-pol. DUB-D-Buchse PC Fig. 4-5: Wiring example for connecting the RS232 interface FEIG ELECTRONIC GmbH Page 41 of 54 M70201-2de-ID-B.doc ENGLISH 4.3.1 RS232 Interface OBID i-scan® Installation ID ISC.MRU200 4.3.2 RS485 / RS422 Interface (ID ISC.MRU200-USB) The second asynchronous interface can be configured for RS485 or RS422 (see 5.3 J1-J8: Interface configuration). The RS485 interface respectively RS422 interface is connected to X3. Terminal Abbreviation Description X3 / Pin 1 GND RS485 / RS422 – GND X3 / Pin 2 A- RS485 / RS422 – (A -) X3 / Pin 3 B+ RS485 / RS422 – (B +) X3 / Pin 4 Y- RS422 – (Y -) X3 / Pin 5 Z+ RS422 – (Z +) X3 ENGLISH Table 4-4: RS485 / RS422 interface pinouts Z+ Y- B+ A- GND Fig. 4-6: Wiring the RSR485 / RS422 interface FEIG ELECTRONIC GmbH Page 42 of 54 M70201-2de-ID-B.doc OBID i-scan® Installation ID ISC.MRU200 4.3.3 Ethernet Interface (ID ISC.MRU200-E) ENGLISH The Reader has an integrated 10 / 100 base-T network port for an RJ45. Connection is made on X7. With structured cabling Cat 5 cables should be used. This ensures reliable operation at 10 Mbps or 100 Mbps. Table 4-5: Ethernet interface pinouts Terminal Abbreviation Description X7 / Pin 1 TX+ Transmit Data + X7 / Pin 2 TX- Transmit Data - X7 / Pin 3 RX+ Receive Data + X7 / Pin 4 VETH+ n.c. X7 / Pin 5 VETH+ n.c. X7 / Pin 6 RX- X7 / Pin 7 VETH- n.c. X7 / Pin 8 VETH- n.c. Receive Data - The prerequisite for using TCP/IP protocol is that each device has a unique address on the network. All Readers have a factory set IP address.. Table 4-6: Standard configuration of the Ethernet connection Network Address IP-Address 192.168.10.10 Subnet-Mask 255.255.255.0 Port 10001 Note: The readers must be connected to the network and configured one after the other. Every IPAddress must be used only one time. Alternatively this configuration can be done with the asynchronous interface. FEIG ELECTRONIC GmbH Page 43 of 54 M70201-2de-ID-B.doc OBID i-scan® Installation ID ISC.MRU200 4.3.4 USB Interface (ID ISC.MRU200-USB) The USB socket on the board is terminal X8. The pinout is standardized. The data rate is reduced to 12 Mbit (USB full speed). A standard USB-cable can be used. ENGLISH Note: The length of the USB-cable can be a max. of 5m (20 inch). It is not allowed to use longer cables. 4.4 Inputs The optocoupler inputs in Terminal X5 are galvanically isolated from the Reader electronics and must therefore be externally supplied. The input LEDs for the optocouplers are switch internally with a series resistor Rint of 500 Ω. Table 4-7: Optocoupler input pin assignments Terminal Abbreviation Description X5 / Pin 1 IN1+ + Input 1 X5 / Pin 2 IN1- - Input 1 X5 / Pin 3 IN2+ + Input 2 X5 / Pin 4 IN2- - Input 2 X5 Rint IN2 Rint IN1 Rext Uext Rext Uext Fig. 4-7: Internal and possible external wiring of the optocoupler inputs For supply voltages of greater than 10 V the input current must be limited to max. 20 mA by an additional external series resistor (see Table 4-8). FEIG ELECTRONIC GmbH Page 44 of 54 M70201-2de-ID-B.doc OBID i-scan® Installation ID ISC.MRU200 External voltage Uext Required external series resistor Rext 5...10 V --- 11...15 V 270 Ω 16...20 V 560 Ω 21...24 V 820 Ω Notes: • The inputs are configured for a maximum input current of 24 VDC and an input current of maximum 20 mA. • Reversing the polarity or overloading the inputs will destroy them. • The Reader supply voltage must not be used to drive the inputs, since otherwise additionally induced noise may reduce the effective reading range. FEIG ELECTRONIC GmbH Page 45 of 54 M70201-2de-ID-B.doc ENGLISH Table 4-8: External Series Resistor OBID i-scan® 4.5 Installation ID ISC.MRU200 Outputs ENGLISH 4.5.1 Optocouplers The transistor connections of the two optocoupler outputs, collector and emitter, are galvanically isolated from the Reader electronics and brought out with no internal circuitry to terminal X4. The outputs must therefore be powered with an external power supply. Table 4-9: Optocoupler output pin configuration Terminal Abbreviation Description X4 / Pin 1 O1-C Collector – Output 1 X4 / Pin 2 O1-E Emitter – Output 1 X4 / Pin 3 O2-C Collector – Output 2 X4 / Pin 4 O2-E Emitter – Output 2 X4 OUT2 OUT1 Fig. 4-8: Internal and possible external wiring of the optocoupler outputs Notes: • The outputs are configured for max. 24 VDC / 30 mA. • Reversing the polarity or overloading the outputs will destroy them. • The outputs are intended for switching resistive loads only. FEIG ELECTRONIC GmbH Page 46 of 54 M70201-2de-ID-B.doc OBID i-scan® Installation ID ISC.MRU200 4.5.2 Relay A changeover relay is provided on terminal X6. Terminal Abbreviation X6 / Pin 1 COM Working contact X6 / Pin 2 NC Normally closed X6 / Pin 3 NO Normally open ENGLISH Table 4-10: Relay output pinouts Description X6 N0 NC Uext COM Fig. 4-9: Internal and possible external wiring of the relay output Notes: • The relay outputs are configured for max. 24 VDC • / 2 A. The relay outputs are intended for switching resistive loads only. If an inductive load is used, the relay contacts must be protected by means of an external protection circuit. FEIG ELECTRONIC GmbH Page 47 of 54 M70201-2de-ID-B.doc OBID i-scan® ENGLISH 5.1 Installation ID ISC.MRU200 Operating and Display Elements LEDs Table 5-1 shows the LED configuration. Table 5-1: LED configuration Abbreviation LED V1 (green) Description "RUN-LED 1" Indicates proper running of the internal Reader software Diagnostic 1: RF communication / EEPROM status Short flashing indicates errorless communication with a transponder on the RF interface Flashes alternately with V1 after a reset following a software update Flashes alternately with V1 in case of a data error when reading the parameters after a reset LED V2 (blue) Diagnostic 2: Host communication LED V3 (yellow) Short flashing indicates sending of a protocol to the host Diagnostic 4: RF warning LED V4 (red) 5.2 Comes on when there is an error in the RF section of the Reader. The error type can be read out via software over the RS232/RS485 interface Reset Button Pressing the button T1 resets the reader. FEIG ELECTRONIC GmbH Page 48 of 54 M70201-2de-ID-B.doc OBID i-scan® 5.3 Installation ID ISC.MRU200 J1-J8: Interface configuration Jumpers J7 and J8 are used to configure the asynchronous interface as an RS485 or R422 port. Jumper RS485 RS422 J7 closed open J8 closed open ENGLISH Table 5-2: Configuration of the RS485 / RS422 port Any termination resistors needed can be enabled using jumpers J1 through J6. Table 5-3: Termination resistors for RS485 / RS422 Jumper closed open J1 Pull-Up on RS4xx - B without Pull-Up on RS4xx - B J2 Pull-Down on RS4xx - A without Pull-Down on RS4xx – A J5 Termination resistor RS4xx - A ⇔ RS4xx - B without Termination resistor RS485 - A ⇔ RS485 - B J3 Pull-Up on RS422 - Z without Pull-Up on RS422 - Z J4 Pull-Down on RS422 - Y without Pull-Down on RS422 – Y J6 Termination resistor RS422 - Y ⇔ RS422 - Z without Termination resistor RS422 - Y ⇔ RS422 - Z 500 Ohm J1 RS485 + J8 J1 500 RS422 Z+ 120 Ohm J7 500 J3 120 J6 RS422 YRS422 B+ J5 J2 RS485 J4 500 Ohm Fig. 5-1: RS485 Interface Jumper FEIG ELECTRONIC GmbH 120 J5 RS422 A500 J2 500 Fig. 5-2: RS422 Interface Jumper Page 49 of 54 M70201-2de-ID-B.doc OBID i-scan® 5.4 Installation ID ISC.MRU200 X62: Boot Loader Mode The pin connector X62 can be closed with a jumper (2.0 mm). Table 5-4: pin connector X62 ENGLISH X62 Description open no effect closed after pressing the button T1 the reader is in th boot loader mode FEIG ELECTRONIC GmbH Page 50 of 54 M70201-2de-ID-B.doc OBID i-scan® Installation ID ISC.MRU200 Technical Data • Housing Die-case aluminum, powder coated, lockable hinged cover • Dimensions ( W x H x D ) 200 x 110 x 60 mm³ (7.9 inch x 4.3 inch x 2.4 inch) • Weight approx. 1,1 kg (2.4 lb) • Enclosure rating IP 54 • Color RAL 7040 (similar to window gray) Electrical Data • Supply Voltage 12...24 VDC ±5% Noise Ripple : max. 150 mV • Power Consumption max. 15 VA • Operating Frequency 869.525 MHz (EN 300 220) 865.6...867.6 MHz (EN 302 208) 902...928 MHz (FCC CFR 47 Part 15.247) • Transmitting Power 100...300 mW (100 mW Step – Software) • Modulation 20...40% and 100% (software configurable) • Receiver Data rates 40 kbps, 64 kbps, 80 kbps • Antenna Connection - 2 x multiplexing 2 x SMA socket (50 Ω) • Outputs: - 2 Optocouplers - 1 Relay (1 x Changeover) 24 VDC 24 VDC / 30 mA (galvanically isolated) /2A • Inputs - 2 Optocouplers FEIG ELECTRONIC GmbH max. 24 VDC Page 51 of 54 / 20 mA (galvanically isolated) M70201-2de-ID-B.doc ENGLISH Mechanical Data ENGLISH OBID i-scan® Installation ID ISC.MRU200 • Interfaces - RS232 - RS485 / RS422 (selectable) - Ethernet (TCP/IP) (ID ISC.MRU200-E only) - USB (ID ISC.MRU200-USB only) • Protocol modes - FEIG ISO Host - Buffer Reader Mode (Data Filtering and buffering) - Scan Mode • Supported Transponders - EPC class 1 Gen 2 - 18000-6-B (UpgradeCode required) • Optical Indicators 4 LEDs for operating status diagnostics • Multi-Reader Operation Synchronization of the air protocols using Reader synchronization Ambient • Temperature range - Operating - Storage • Vibration • Shock -25...+55°C (-13...+131°F) -25...+85°C (-13...+185°F) EN60068-2-6 10...150 Hz : 0.075 mm / 1 g EN60068-2-27 Acceleration : 30 g Applicable Standards • RF approval - Europe - USA • EMC EN 302 208 / EN 300 220 FCC 47 CFR Part 15 EN 301 489 • Safety - Low-Voltage - Human Exposure FEIG ELECTRONIC GmbH EN 60950 UL 60950-1 EN 50364 Page 52 of 54 M70201-2de-ID-B.doc OBID i-scan® 6.1.1 ID ISC.MRU200 Approval Europe (CE) When properly used this radio equipment conforms to the essential requirements of Article 3 and the other relevant provisions of the R&TTE Directive 1999/5/EC of March 99. Equipment Classification according to ETSI EN 302 208 and ETSI EN 301 489: Class 2 6.1.2 USA (FCC) FCC ID: PJMMRU200 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTICE: Changes or modifications made to this equipment not expressly approved by FEIG ELECTRONIC GmbH may void the FCC authorization to operate this equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FEIG ELECTRONIC GmbH Page 53 of 54 M70201-2de-ID-B.doc ENGLISH 6.1 Installation OBID i-scan® Installation ID ISC.MRU200 ENGLISH 6.1.3 USA and Canada (UL) NOTE: To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that permitted for successful communication. This device has been designed to operate with the antennas listed below, and having a maximum gain of 10.5 dBic. Antennas not included in this list or having a gain greater than 10.5 dBic are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Lists of Antennas: ID.ISC.ANT.U250/250-FCC ID.ISC.ANT.U170/170-FCC ID ISC.ANT.U270/270-FCC ID ISC.ANT.U600/270-FCC FEIG ELECTRONIC GmbH Page 54 of 54 M70201-2de-ID-B.doc
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 54 Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:c429bd33-08e8-4301-9295-7de36d0795f0 Producer : Acrobat Distiller 6.0.1 (Windows) Create Date : 2009:07:24 12:36:07+02:00 Creator Tool : PScript5.dll Version 5.2 Modify Date : 2009:08:19 10:28:36+02:00 Metadata Date : 2009:08:19 10:28:36+02:00 Document ID : uuid:83e6cded-8721-4374-ba1f-114e26e57cd5 Format : application/pdf Creator : Wennrich Title : M70201-2de-ID-B.doc Author : WennrichEXIF Metadata provided by EXIF.tools