Fender Service Manual Passport PD 150 Rev 2

User Manual: Fender Passport PD-150 Rev 2 Service Manual Fender Audio Schematic Archive – Fender

Open the PDF directly: View PDF PDF.
Page Count: 48

DownloadFender Service Manual  Passport PD-150 Rev 2
Open PDF In BrowserView PDF
PASSPORT® PD-150
(This is the model name for warranty claims)
p/n 069-2005-003

SERVICE MANUAL

ATTENTION:
WARRANTY SERVICE PROCEDURES
Warranty field service of the Passport PD-150 will be to the Module or PCB Assy. level.
Non-Warranty repairs of course can be to the component level at the Service Center’s
discretion. Please note for non-warranty repairs that all parts marked “REF” in the Parts
List will need to be sourced from suppliers other than FMIC.

Fender Musical Instruments Corporation, 8860 East Chaparral Road Suite 100 Scottsdale, AZ 85250
Issued: June, 2007

2

®

PASSPORT PD-150
(This is the model name for warranty claims)

IMPORTANT NOTICE

Copyright © 2007 FMIC. All rights reserved. All
information contained herein is CONFIDENTIAL
and PROPRIETARY and is the property of Fender® Musical Instruments Corporation. It is not to
be sold or assigned to another party and is disclosed solely for use by Fender Authorized
Service Centers for purposes of product service
and maintenance. All information is not to be disclosed to others without the expressed permission
of Fender® Musical Instruments Corporation. All

specifications are subject to change without notice. This information and any copies produced
electronically or otherwise must be surrendered
upon demand of Fender® Musical Instruments
Corporation.
Parts marked with two asterisks (**) indicate the
required use of that specific part. This is necessary for RELIABILITY and SAFETY requirements.
DO NOT USE A SUBSTITUTE!

PARTS LIST CODES
The description codes used in the itemized Parts Lists are defined below:
CAPACITOR CODES
CAP AE
= Aluminum Electrolytic
CAP CA
= Ceramic Axial
CAP CD
= Ceramic Disk
CAP CR
= Ceramic Radial
CAP MPF = Metalized Polyester Film
CAP MY
= Mylar
CAP PFF = Polyester Film/Foil
RESISTOR
RES CC
RES CF
RES FP
RES MF
RES MOX
RES WW

CODES
= Carbon Comp
= Carbon Film
= Flame Proof
= Metal Film
= Metal Oxide
= Wire Wound

HARDWARE CODES
BLX
= Black Oxide
CR
= Chrome Plated
HWH
= Hex Washer Head
M
= Machine Screw
NI
= Nickel Plated
OHP
= Oval Head Phillips
PB
= Particle Board
PHP
= Pan Head Phillips
PHPS
= Pan Head Phillips Sems
SMA
= Sheet Metal "A" Point
SMB
= Sheet Metal "B" Point
SS
= Stainless Steel
TF
= Thread Forming
ZI
= Zinc Plated

3

®

PASSPORT PD-150
(This is the model name for warranty claims)

SPECIFICATIONS
Model Name:

PASSPORT PD-150

Release Number:

PR483

Part Number:

(120V, 60Hz) US:
(120V, 60 Hz) DS:
(240V, 50 Hz) AUS:
(230V, 50 Hz) UK:
(230V, 50 Hz) EUR:
(100V, 50 Hz) JPN:

Frequency Response:
Distortion:
Signal to Noise Ratio:
Power Output:

069-2005-003
069-2005-903
069-2005-033
069-2005-043
069-2005-063
069-2005-073
30 Hz to 20 kHz ± 1 dB (at speaker output)
30 Hz to 20 kHz ± 1 dB (at send output)
< 0.1%, 20 Hz to 20 kHz, 1dB below rated output
> 80 dB @ 1W, “A” WTD
75W/ch continuous average power, 8Ω, both channels driven with
THD <1%

Input Impedance:
(Channels 1, 2, 3 XLR and 1/4”)
(Phono and Stereo Channel 1/4”)
Max. Input Level:
Mic:
Line:
Stereo:
Return Input Impedance:
Fuse type:
Passport System:
Width:
Height:
Depth:
Weight:
Speakers:
Width:
Height:
Depth:
Weight:
Power Tower:
Width:
Height:
Depth:
Weight:
Tower Footprint:
Microphone:
Microphone Cable:
Speaker Cables:

“Mic” switch position: 2 kΩ
“Line” switch position: 66 kΩ
78 kΩ
-7 dBu
30 dBu
26 dBu
47kΩ
T4AH, 250V
610 mm (24 in.)
541 mm (18 in.)
254 mm (10 in.)
15.91 kgs (35 lbs)
245 mm (9.65 in.)
439 mm (17.5 in.)
241 mm (9.5 in.)
4.08 kgs (9.0 lbs)
254 mm (10 in.)
451 mm (18 in.)
178 mm (7 in.)
6.80 kgs (15.00 lbs)
241 x 298 mm (9.5 x 11.75 in.)
Dynamic Cardioid, balanced
XL -Male to XL-Female, 6 m (20 feet)
1/4 in. to 1/4 in., 9 m (30 feet)

0 dBu is referenced to 0.775 volts rms

4

®

PASSPORT PD-150
(This is the model name for warranty claims)
Product specifications are subject to change without notice

SERVICE NOTES
The following describes the procedure to dismantle
the PD-150 Cabinets.
STEP A: PD-150 CABINET
A1.

Unscrew two M4 machine screws on each of
the left and right hatches on either side of the
unit (8 total).

B3.

Unscrew nine M3 machine screws from the
mixer PCB assembly.

B4.

Detach all connectors.

B5.

The procedure is completed.

STEP C: PD150 DSP REVERB PCB
C1. Detach all connectors.

A2.

Unscrew two M3 pan-head machine screws
on the handle cover and detach it.

A3.

Place the unit upside down. Unscrew eight M4
self-tapping screws off the foot standers.

A4.

Detach the foot standers. There are six M3
self-tapping screws in the middle portion.

A5.

Unscrew three M3 self-tapping screws located
on the right-hand-side.

A6.

Place the unit in the normal position.

D3. The procedure is completed.

A7.

Locate the four M3 and two M4 self-tapping
screws on the top and unscrew them.

STEP E: PD150 POWER AMP PCB

A8.

Separate the left and right cabinets.

E1.

A9.

Locate the UHF and VHF antennas on the
right and left cabinets respectively.

Unscrew four screws connecting the heat sink
to the side brackets (two on either side of
tower).

A10. De-solder both antennas.

E2.

Detach all connectors.

A11. Unscrew three M3 self-tapping screws on left
and right side panels (6 total) of the tower
metal assembly.

E3.

The procedure is completed.

A12. Unscrew eight M2.6 and eight M3 self-tapping
screws (three on top of front panel, three on
top of rear panel, and two on metal cover).

F1.

Unscrew three screws from the front panel.

F2.

Detach all wiring and connectors.

F3.

Unscrew six screws from the top cabinet of
the SMPS.

F4.

Unscrew three screws from the bottom cabinets of the SMPS.

F5.

Detach the spacer from the wiring of the
SMPS.

F6.

Unscrew the earthing M4 nut.

F7.

Detach the mains connector from the AC inlet.

F8.

Unscrew five screws from the SMPS PCB assembly

F9.

The procedure is completed.

A13. Detach the left and right metal side panels.
A14. Detach the top metal cover.
A16. Unscrew seven outer M3 self-tapping screws
on the rear panel.

C2. The procedure is completed.
STEP D: PD150 INPUT PCB
D1. Unscrew six screws and nuts from the front
panel.
D2. Detach all connectors.

STEP F: PD150 SMPS PCB

A17. Detach all connectors.
A18. The procedure is completed.
STEP B: PD150 MIXER PCB
B1.

Detach 24 knobs and their nuts.

B2.

Detach the Reverb PCB assembly.

5

®

PASSPORT PD-150
(This is the model name for warranty claims)

PCB EXCHANGE POLICY
Parts marked with a single asterisk (*) in the Part
Lists are not field replaceable. If a failure due to
one of these components is detected, please

contact the FMIC Customer Service Department to
order the complete PCB Assembly.

CIRCUIT DESCRIPTION
This section provides concise information about new
or unusual circuitry designs incorporated into this
amplifier model. The purpose is to aid the service
technician by providing insight into the design areas
most likely to become obstacles in troubleshooting.
Information is focused for its effective use while
maintaining the security of Fender® proprietary
information wherever possible.
The PD-150 consists of the following modules.
1. Mixer Section
2. Digital Reverb Section
3. Signal Processor Circuit and System EQ Circuit
4. Power Amplifier
5. Switch Mode Power Supply Unit (SMPSU)

The Mixer PCB module
The mixer section is mainly made up of operational
amplifiers as gain stages and therefore a technical
description will not be used here. Following is a basic circuit description to familiarize you with the
layout of the circuit.
The Mic/Line section is made up of 3 microphone /
line inputs each with a first stage preamplifier for
balanced or unbalanced inputs (locate on the mixer
board). Line inputs can operate as either balanced
or unbalanced if TRS or TR 1/4" jacks are used respectively. Gain selection of 1dB/+30dB is made by
switching a different value resistor in the input
stage. At this point on channel one, the signal is
picked off for the VIP control ducking circuit made
up of U1B.
After the input stage there is one knob for contour
control, followed by an auto-pad level control where
the signal splits off into the rev/aux bus and main

signals. The main signals are then routed to a pan
circuit. Here the main signal is split between the left
and right channel signal bus. Channel three also
has an additional input via a pair of RCA connectors
where the signals are summed into mono which
may be used as an auxiliary audio signal input.
The stereo mixer section consists of a stereo pair
inputs with RCA and 1/4" stereo phone jack connections. This circuit consists of an auto-pad level
control, low frequency and high frequency tone controls, Rev/Aux send control and balance control with
signals feeding the left and right audio bus. The
audio bus is connected to three FETs that perform
ducking of the signals on the bus with the exception
of channel one which is the drive circuit for the VIP
ducking circuit. This function is provided by U1B.
Bus signals are buffered by U8A/B and drive the
tape output connections and drive the main left and
right master level control circuitry made up of
U9A/B. The Rev/Aux signals are buffered by U12B
and feed the mono aux send output. Main left and
right level controls are auto-pad configuration and
drive the speaker EQ circuitry made up of U10A/B.
Note: Channel 1 Mic/Line reverb function will be affected by VIP control making announcements on
Channel 1 dry.
The mixer board also contains part of the signal
processor circuit and the system EQ circuit for the
power amplifier. These circuits are an integral part
of the power amplifier and appear after the return
signal path.
These circuits will all be discussed later in this document.

6

®

PASSPORT PD-150
(This is the model name for warranty claims)
The DSP Reverb PCB Module
The DSP Reverb PCB module receives the input
REV/AUX signals at pin 4 of connector CN401. The
DSP Reverb’s IC’s consist of U404 (AL1101 ADC),
U405 (AL1201 DAC), and U406 (AL3201B). The
outputs from U405 are fed to U402B and then buffered by U402A before feeding back to pin 6 of CN
401.

Signal Processor & System EQ Circuit
The signal processor is partially located on the mixer board but is an integral part of the power
amplifier section. The operation of this circuit is performed by filtering the signal from U11A/B which
drives the bases of Q5 and Q7 to control the voltage level at FETs Q4 and Q6 respectively. This in
turn changes the filter characteristics of circuits
which at low levels boosts the low and high frequencies of the signal. At high signal levels with the
gate voltages approaching or at 0v, the circuit lowers the boost of the low frequencies in response.
This circuit is post aux return and therefore does
not modify the response of the signal at the aux
send outputs.

Power Amplifier PCB module
Note: In cases where the amplifier circuits are identical between the left and right channel, only
components related to the left channel will be discussed for simplicity.
The first stage of the power amplifier is made up of
op amp U201A that acts as the input buffer and
muting circuit for minimization of turn on/off pops.
Q202 in balance with the input resistors of this circuit are designed to provide a deep muting effect.
This circuit will be called into action if the temperature of the heat sink also rises above 80 degrees
Centigrade. (Typical HS temperature is around 50
for normal operation). The output of the first stage
feed trimmer resistor TP201 which are part of the
balanced input section of low noise op-amp U202A
which sets the amplifier gain (factory set at approximately 30.5dB). The output of the second stage

directly drives the biased gates of lateral power
FETs Q204 and Q205.
Speaker short circuit protection is provided by
U203B. This is accomplished when the output is
shorted to ground, the normal differential signal applied to U203B is absent at the negative terminal
while at the same time, the second stage is now
forced into open loop gain. The drive signal is integrated into C207 forcing a positive voltage at the
output of U203 that pulls the gate of FET Q203 into
conduction from its previous negative bias off point,
nulling the output of U202A. With the output of
U202A minimized the output current of the amplifier
is minimized until the short is removed. At this time,
C207 will discharge allowing normal operation of
the amplifier. Note: Some small DC offset will be
present when the amplifier is in the short circuit protect mode.
The power amplifier board also provides the ±15v
for the Mixer and DSP reverb boards as well as the
supply for the SMPSU FAN and the LED PCB
which indicated power and thermal protection modes. The power amplifier board is also connected to
the GM type fuse holder and aux DC power input
connector.

The SMPS PCB Module
This unit is not recommended to be serviced in
the field except by replacing the complete module as a total assembly. The following information
is provided to assist in the trouble shooting of the
unit. Please note that the mains fuse must be replaced with exactly the same grade of fuse for
safety regulations and to avoid risk of damage and
potential fire hazard.
The mains input to the SMPSU allows for operation
from 90-130V in 115V setting and 190-250V in the
230V setting. The output of the SMPSU is ±42V
DC for the main power supply rails of the power
amplifier. The unit also has connectors for mains
power input, mains power switch and chassis, earth
and signal grounds.
Service Tip: You can connect to the aux DC input
(with GM fuses installed) to test the output voltage

7

®

PASSPORT PD-150
(This is the model name for warranty claims)
to the rails before you open the set for service to
get an indication of a possible power supply fault as
it is connected to the rail output. Do not short these
terminals!
The SMPSU incorporates protection circuits other
than the fuses including over current protection. All
parts contained in the SMPSU should be considered to be safety parts and should be replaced
with only exact where service can be provided by
properly licensed and trained repair technicians.
This includes the dust filter as well as it has a fire
hazard rating. Please be aware that voltages contained in this module are deadly!!

Service Notes on Changes and Upgrades
A 0.01uF mylar film capacitor has been added to
the VIP ducking circuit to prevent a slight hum that
may be heard as an artifact at the tail of the ducking
action. This was mainly detected on UL voltage settings. This capacitor is added at the junction of R18
(1Mega ohm) and D16 and the Source (Ground) of
FET Q3 (J112). This modification should be performed on individual units that are listed below by
S/N. All other UL units have been modified by the
factory.

8

®

PASSPORT PD-150
(This is the model name for warranty claims)

.PARTS LIST:

MIXER - PCB ASSEMBLY

QTY

PART #

1

0070378000

*MIXER REPAIR MODULE

1

REF

PCB ASSY MIXER

6

REF

CC 50V 100P 10% RL 5X3

C3-4 C15-16 C26-27

REF

CC 50V 27P 10% RL 5X3

C9 C11 C21 C23 C32 C34 C37-38 C43 C46
C52 C57 C62 C69 C78-81

6

REF

CM 100V 0.001UF 10% RL 5x7.5

C20 C31 C41 C45 C83-84

1

REF

CM 100V 0.01UF 10% RL 6x7.5

C87

2

REF

CM 100V 0.1UF 10% RL 9x11 CENTRALAB

C85-86

3

REF

CM 100V 0.0015UF 10% RL 5X7.5

C7 C18 C29

3

REF

CM 100V 0.015UF 10% RL 6x9.5

C8 C19 C30

4

REF

CM 100V 0.0022U 10% 5x7.5

C63 C67 C70 C74

2

REF

CM 100V 0.022UF 10% RL

C42 C44

4

REF

CM 100V 0.0047UF 10% RL 5.3X7.5

C54-55 C59-60

2

REF

CE 25V 47U 20% RLR 5X11 ELNA

C47-48

REF

CE 50V 1U 20% RLR 5x11 ELNA

C6 C10 C22 C33 C35-36 C39-40 C65 C72
C82

REF

CE 50V 2.2uF 20% RL 5x11

C1-2 C13-14 C24-25

REF

CE 50V 0.47uF 20% RL 5x11

C5 C17 C28 C49-51 C53 C56 C58 C61 C68
C75

REF

CE 50V 4.7uF 20% RL 5x11

C66 C73

REF

CE 50V 4.7U 20% RLR 5x11 ELNA/NCC/MATSUSHITA

C12

2

REF

CE 50V 47uF 20% RL 8x12

C76-77

2

REF

CE 50V 0.56U 20% RLR 5X11

C64 C71

1

REF

PCB MIX S/S CEM-1 PD150

1

REF

WAFER JM24182-3P

CN8

5

0070067000

PJ6-09-5STEREO JACK W/O NUT 5P

PJ1-4 PJ6

2

0070068000

MONO JACK PJ6-09-3 W/O NUT DIAMOND

PJ5 PJ7

10

REF

IC TL072CP DUAL FET OP AMP TI

U2 U4-9 U10-12

2

REF

IC LM833N NS

U1 U3

1

REF

IC TL072CDR DUAL J-FET INPUT OP-AMP (SMD)

U13

4

REF

CS-0813 PCB SUPPORT

REF

RCF 1/8W 10K 5% AT

R11 R63-66 R75 R80 R90-91 R129 R137138

REF

RCF 1/8W 100K 5% AT

R20-21 R38-39 R58-59 R76 R79 R86-87
R92 R95 R97 R99 R122 R139 R145

9

REF

RCF 1/8W 1M 5% AT

R17-19 R108 R118 R132-135

3

REF

RCF 1/8W 110K 5% AT

R82 R84 R120

5

REF

RCF 1/8W 2.2M 5% AT

R16 R107 R109 R117 R119

18

11
6
12
2
1

12
17

*
shaded
shaded + *
**
shaded + **

DESCRIPTION

REFERENCE DESIGNATION

Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
Unique Fender® part. Order directly from the FMIC Parts Department.
Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
Both a unique Fender® part and a Safety Requirement part as defined above.

9

®

PASSPORT PD-150
(This is the model name for warranty claims)

.PARTS LIST:
QTY

MIXER - PCB ASSEMBLY

PART #

DESCRIPTION

REFERENCE DESIGNATION

REF

RCF 1/4W 1K 5% ATS

R1-3 R6 R15 R25-27 R30 R43-46 R88-89
R147-148

REF

RCF 1/4W 11K 5% ATS

R131 R146

REF

RCF 1/4W 12K 5% ATS

R9 R14 R33 R37 R53 R57 R102 R105 R112
R116

8

REF

RCF 1/4W 27K 5% ATS

R67-74

2

REF

RCF 1/4W 3.3K 5% ATS

R104 R114

REF

RCF 1/4W 33K 5% ATS

R4-5 R7-8 R28-29 R31-32 R49-52 R93-94
R96 R98 R143-144

REF

RCF 1/4W 39K 5% ATS

R10 R13 R34 R36 R54 R56 R100-101
R110-111 R123 R130 R141-142

4

REF

RCF 1/4W 470R 5% ATS

R22-24 R136

1

REF

RCF 1/4W 56K 5% ATS

R124

7

REF

RCF 1/4W 6.8K 5% ATS

R83 R85 R103 R106 R113 R115 R121

REF

RCF 1/4W 82K 5% ATS

R12 R35 R40-42 R47-48 R55 R60-62 R7778 R81 R125-128

REF

RMF 2W 3.3R 5% ATS METAL OXIDE

R140

12

0070083000

VR RK14K1240 100KBx2 W/C.C (ALPS)

VR1 VR5-6 VR9-10 VR13 VR15-20

10

0070082000

VR RK14K1240 (100KBx2) ALPS

VR2-4 VR7-8 VR11-12 VR14 VR21-22

16

REF

DIODE 1N4148TA NS

D1-16

2

REF

TR FET J112

Q4 Q6

6

REF

TR FET J112-TR1-E3 RLT

Q1-3 Q8-10

2

REF

TR MPS A56 VCE 80V NS

Q5 Q7

1

REF

TR MPS A56 VCE 80V NS RL T

Q11

4

0070443000

SW-SLIDE 2P2T SS2214RG9 Y.S.C.

SW1-4

1

REF

CN ASSY UL1007 #26 L=80 15P F/M P2.5

CN1

1

REF

CN ASSY UL2547 #26 L=170 3P M/M P2.5

CN3

1

REF

CN ASSY UL2547 #26 L=210 3P M/M P2.5

CN4

1

REF

CN ASSY UL2547 #26 L=250 3P F/M P2.5

CN5

17
2
10

18.
14

18
1

.PARTS LIST: RCA/XLR INPUT - PCB ASSEMBLY
QTY

PART #

1

0070450000

*PCB ASSY RCA

1

REF

PCB RCA 2751-2 REV:E

1

REF

WAFER 15P ST. P=2.5 COULOMB

CN1

1

0074657000

6P RCA JACK AU HSP-206V-03

RJ1

3

0070078000

MIC JACK SVP561P-R

MJ1-3

*
shaded
shaded + *
**
shaded + **

DESCRIPTION

REFERENCE DESIGNATION

Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
Unique Fender® part. Order directly from the FMIC Parts Department.
Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
Both a unique Fender® part and a Safety Requirement part as defined above.

10

®

PASSPORT PD-150
(This is the model name for warranty claims)

.PARTS LIST:

DSP REVERB - PCB ASSEMBLY

QTY

PART #

1

0070104000

*PCB ASSY DSP REVERB

DESCRIPTION

REFERENCE DESIGNATION

1

REF

*2P ST.WAFER P=2.5 COULOMB

CN403

19

REF

*CC 50V 0.1uF 10% 0805

C405-406 C412-419 C422-427 C431-432
C434

2

REF

*CC 50V 220pF 10% 0805 1. 2x2.0

C407 C409

1

REF

*CC 50V 4700pF 10% 0805 1 .2x2.0

C404

1

REF

*CC 50V 470pF 10% 0805

C408

7

REF

*CE 50V 10UF 20% RLT 5X11 SHOEI

C401-403 C410-411 C430 C433

1

REF

*CE 50V 1UF 20% RLT 5X11 SHOEI

C420

2

REF

*CE 50V 47UF 20% RLT 6.3X11 SHOEI

C428-429

1

REF

*CN ASSY UL1007 #26 L=180 2P F/M P2.5

CN402

1

REF

*IC AL1101G WAVEFRONT ADC

U404

1

REF

*IC AL1201G WAVEFRONT DAC

U405

1

REF

*IC AL3201BG WAVEFRONT DIGITAL REVERB

U406

1

REF

*IC L78L05ACZ ST

U407

3

REF

*IC NJM2068M-#ZZZB DUAL OP AMP

U401-403

1

REF

*JM24182-2P WAFER

CN402, C403

1

REF

*JM24182-6P WAFER

CN401

1

REF

*PCB DSP REVE D/S FR4 10Z REV: D EFPAP150D+05CS21

1

REF

*RMG 1/10W 100K 5% 0805

R401

8

REF

*RMG 1/10W 10K 5% 0805

R408 R410-411 R416 R418-421

1

REF

*RMG 1/10W 1K 5% 0805

R417

4

REF

*RMG 1/10W 2.2K 5% 0805

R402-405

3

REF

*RMG 1/10W 220R 5% 0805

R406-407 R413

2

REF

*RMG 1/10W 4.7K 5% 0805

R409 R412

1

REF

*RMG 1/10W 47K 5% 0805

R415

1

REF

*RMG 1/8W 10R 5% 1206

R414

1

REF

*X'TAL 12.288MHZ +/- 30PPM 49U

XL401

1.2X2.0

1.2X2.0

.PARTS LIST: LED INDICATORS - PCB ASSEMBLY
QTY
1

PART #

DESCRIPTION

REFERENCE DESIGNATION

0074656000
1

*PCB ASSY LED

1

REF

*PCB POWER AMP 2751-3/-6 REV:D

1

REF

*LED RED/GREEN L-937EGW 3MM

LED201

1

REF

*CN ASSY UL1007 #26 L=220 2P F/M P2.5

CN205

*
shaded
shaded + *
**
shaded + **

Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
Unique Fender® part. Order directly from the FMIC Parts Department.
Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
Both a unique Fender® part and a Safety Requirement part as defined above.

11

®

PASSPORT PD-150
(This is the model name for warranty claims)

.PARTS LIST:
QTY

SMPS- PCB ASSEMBLY

PART #

DESCRIPTION

1

0070504000

*SMPSU REPAIR MODULE

1

REF

PCB ASSY SMPS

3

REF

CC 50V 0.1U 20% RLF

C310-311 C316

1

REF

CC 50V 470P 10% RL 5x3

C308

1

REF

CC 1KV 100PF 10% RL 7x4.5

C317

2

REF

CC 1KV 470PF 10% RL 7x4.5

C318-319

REF

**CC 400V 1000P 20% RL Y5 U 9.5X8
AH09E102MLO

C303-304 C326-327

1

REF

CM 100V 0.01UF 10% RL 6x7.5

C312

1

REF

CM 100V 0.0022U 10% 5x7.5

C314

2

REF

CM 100V 0.0047UF 10% RL 5.3X7.5

C313 C315

REF

**CM 280V 0.22UF 20% RL 26.5X16.5 METALLIZED

C301-302

1

REF

CE 25V 10uF 20% RL 5x11

C309

1

REF

CE 50V 1U 20% RL 5x11 ELNA

C323

1

REF

CE 50V 100uF 20% RL 8x12

C307

1

REF

PCB SMPS S/S CEM-1 PD150

1

REF

**PWR TXFR ETD-39 KSF-1689 -00

T303

REF

**CHOKE-COMMON MODE 15MH 4A 180MOHM
DIP

T305 T307

1

REF

TRB 12X6X4 TOROIDAL KS-8 51N-1

T302

1

REF

KS-1554-03 TOROIDAL T131 -26

L302

2

REF

FERRITE BEAD INDUCTOR BL01RN1A1F1J

FB301-302

1

REF

**ARRESTER 230V DC 5KA M2P -230L

G301

1

REF

**WAFER 2P P7.92 STRAIGHT

CN301

2

REF

WASHER SPRING M3X0.9X5.5 BZ

IRF840

2

REF

M3 NUT NI

IRF840

2

REF

SCREW BH M3X 14 MM BZ CROSS

IRF840

REF

SCREW B-TITE PH M3X 8 MM YZ CROSS W/
WASHER

FEP16GT

REF

MICA T-400 T03P 25X20M TO-3P

REF

IC REGULATOR SMPS CONTROL KA3842B
DIP-8

U301

2

REF

2688-15-0 TH/SW BKT

IRF840

2

REF

INSULATION BUSHING (115DEG.C.)

FEP16GT

3

REF

RCF 1/4W 1K 5% AT

R308 R313 R315

1

REF

RCF 1/4W 100K 5% AT

R304

1

REF

RCF 1/4W 1M 5% AT

R305

1

REF

RCF 1/4W 22K 5% AT

R307

4

2

2

2
4
1

*
shaded
shaded + *
**
shaded + **

REFERENCE DESIGNATION

Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
Unique Fender® part. Order directly from the FMIC Parts Department.
Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
Both a unique Fender® part and a Safety Requirement part as defined above.

12

®

PASSPORT PD-150
(This is the model name for warranty claims)

.PARTS LIST:
QTY

SMPS- PCB ASSEMBLY

PART #

DESCRIPTION

REFERENCE DESIGNATION

1

REF

RCF 1/4W 2.7K 5% AT

R325

1

REF

RCF 1/4W 3.9K 5% AT

R309

1

REF

RCF 1/4W 39K 5% AT

R321

2

REF

RCF 1/4W 470R 5% AT

R310 R322

2

REF

RCF 1/4W 47K 5% AT

R323-324

2

REF

RCF 1/4W 51R 5% AT

R312 R314

1

REF

RCF 1/4W 680R 5% AT

R306

2

REF

RCF 1/2W 100K 5% AT

R302-303

1

REF

RCF 1/2W 470K 5% AT

R301

1

REF

RMF 1/4W 220R 1% AT

R311

1

REF

RMF 1W 2K 5% ATS METAL OXIDE

R320

1

REF

RMF 2W 100R 5% ATS METAL OXIDE

R317

2

REF

RMF 2W 47R 5% ATS METAL OXIDE

R318-319

1

REF

RMF 3W 0.22R 5% ATS METAL OXIDE

R316

1

REF

SVR B1K H3 VZ067TL7B 6.3X 6.8 HDK

TP301

2

REF

DIODE FEP16GT-E3/45 (GI)

D308-309

1

REF

**DIODE KBU6J-E3/1 600V (GI)

D301

1

REF

DZ 1/2W 12V 5% TEMIC AT

Z305

4

REF

DZ 1/2W 18V TEMIC AT

Z301-304

3

REF

DIODE 1N4148TA NS

D303-305

1

REF

RECTIFIER UF4003-T GI AT

D302

2

REF

RECTIFIER UF4006-T GI AT

D306-307

1

REF

TR TL431CLP TI

U303

2

REF

**TR FET IRF840PBF IR

Q301-302

1

REF

**SW CB-SL1412 AM1BCEI AC SELECTOR

SW302

1

REF

**NTC THERMISTER SCK055 THINKING

NTC301

2

REF

TRA HEAT SINK 2751-8-0

1

REF

CN ASSY UL1007 #20 L=120 BROWN W/T'ANL

JPW1

1

REF

CN ASSY UL1007 #20 L=120 RED W/T'NAL

JPW2

1

REF

**OPTOCOUPLER CNY17G-2 (TEMIC)

U302

2

REF

**E.CAP 330UF+-20% 200V 22x30 (ELNA)

C305-306

REF

CE 63V 20% 1000U RL16x30 NICHICON/16x25
PANASONIC

C320-321

2

*
shaded
shaded + *
**
shaded + **

Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
Unique Fender® part. Order directly from the FMIC Parts Department.
Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
Both a unique Fender® part and a Safety Requirement part as defined above.

13

®

PASSPORT PD-150
(This is the model name for warranty claims)

.PARTS LIST: POWER AMPLIFIER - PCB ASSEMBLY
QTY

PART #

1

0070526000

*PCB ASSY POWER AMP

2

REF

CC 50V 0.1U 20% RLF

C224-225

2

REF

CC 50V 0.22UF 20% RLF MO NO

C206 C216

4

REF

CC 50V 47P 10% RL 5X3

C203 C205 C213 C215

2

REF

CM 100V 0.022UF 10% RL

C208 C218

2

REF

CM 100V 0.22UF 10% RL 11.5x13

C209 C219

2

REF

CE 16V 22uF 20% RL 5x11

C204 C214

7

REF

CE 25V 47U 20% RL 5X11 E LNA

C210-211 C220-223 C228

4

REF

CE 50V 1U 20% RL 5x11 EL NA

C202 C207 C212 C217

1

REF

CE 50V 2.2uF 20% RL 5x11

C201

2

REF

CE 100V 10uF 20% RL 6.5x11

C226-227

1

REF

**PCB POWER AMP 2751-3/-6 REV:D

1

REF

JM2422-2M WAFER

CN201

2

REF

JM2422-4M WAFER

CN202-203

3

REF

JM24182-2P WAFER

CN6 CN204-205

1

REF

WAFER JM24182-3P

CN5

2

0070311000

MONO JACK PJ6-09-3 W/O NUT DIAMOND

PJ201-202

1

REF

IC TL072CP DUAL FET OP AMP TI

U201

2

REF

IC BA4560 ROHM

U202-203

2

REF

RCF 1/8W 10K 5% AT

R205 R227

4

REF

RCF 1/8W 100K 5% AT

R206 R219 R228 R242

4

REF

RCF 1/8W 1M 5% AT

R220-221 R243-244

1

REF

RCF 1/8W 2.2M 5% AT

R202

4

REF

RCF 1/8W 3.3M 5% AT

R222 R225 R245 R248

6

REF

RCF 1/8W 390R 5% AT

R207 R215-216 R229 R238-239

1

REF

RCF 1/4W 1K 5% ATS

R250

1

REF

RCF 1/4W 1.5K 5% ATS

R210 R212 R232 R234

4

REF

RCF 1/4W 15K 5% ATS

R214 R217 R237 R240

1

REF

RCF 1/4W 2K 5% ATS

R251

5

REF

RCF 1/4W 39K 5% ATS

R201 R203-204 R208 R230

2

REF

RCF 1/4W 390K 5% ATS

R223 R246

2

REF

RCF 1/4W 4.7K 5% ATS

R211 R233

2

REF

RCF 1/4W 56K 5% ATS

R218 R241

2

REF

RMF 1/8W 5.1K 1% AT

R209 R231

4

REF

RMF 2W 3.3K 5% ATS METAL OXIDE

R224 R226 R247 R249

3

REF

RMF 2W 3.3R 5% ATS METAL OXIDE

R213 R235-236

3

REF

RWR 5W 270R 5% AL

R252-254

*
shaded
shaded + *
**
shaded + **

DESCRIPTION

REFERENCE DESIGNATION

Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
Unique Fender® part. Order directly from the FMIC Parts Department.
Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
Both a unique Fender® part and a Safety Requirement part as defined above.

14

®

PASSPORT PD-150
(This is the model name for warranty claims)

.PARTS LIST: POWER AMPLIFIER - PCB ASSEMBLY
QTY

PART #

DESCRIPTION

REFERENCE DESIGNATION

2

REF

SVR B1K H3 VZ067TL7B 6.3X 6.8 HDK

TP201-202

4

REF

DZ 1/2W 15V 5% TEMIC AT

Z202-205

1

REF

DZ 1/2W 33V TEMIC AT

Z201

1

REF

DZ 1W 12V AT TEMIC

Z208

2

REF

DZ 1W 15V AT TEMIC

Z206-207

11

REF

DIODE 1N4148TA NS

D201-211

4

REF

TR FET J112

Q202-203 Q206-207

1

REF

TR MPSA06 VCE 80V NS

Q201

1

REF

**THERMAL SW 17AM203A5-4

TH201

1

REF

CN ASSY UL1007 #26 L=100 2P M P2.5

CN206

.PARTS LIST: WIRELESS REG - PCB ASSEMBLY
QTY

PART #

DESCRIPTION

1

0070376000

*PCB ASSY REG

1

REF

CC 50V 0.1U 20% RLF

C601

1

REF

CE 50V 1U 20% RL 5x11 ELNA

C602

1

REF

PCB REG 2751-6

PCB-6

2

REF

JM24182-2P WAFER

CN601-602

1

REF

IC LM317HVT/NOPB REGULATOR

U601

1

REF

RMF 1/4W 1.3K 1% AT

R601

1

REF

RMF 1/4W 240R 1% AT

R602

1

REF

WIRE-CONN 2P P2.5 #26 UL1007 L=200 BK/RD F

.PARTS LIST:
QTY

PART #

REFERENCE DESIGNATION

PACKING MATERIALS

DESCRIPTION

REFERENCE DESIGNATION

1 REF

GIFT BOX PD150

PACKING

2 REF

CARTON BOARD 2751-P7-0

2 REF

INNER PAD 2751-P1-B

4 REF

INNER PAD 2751-P14-0

1 REF

CARTON-OUTER 700X520X285 B-B EFPAPD150+05CS17

1 REF

CARTON SHEET 1100x2200MM 1-PLY

2 REF

INNER PAD 480X230X3 A-A EFPAPD150+05CS17

1 REF

PE FOAM 2751-P5-0

2 REF

PE FOAM 2751-P4-0

PACKING

1 REF
PE FOAM 2751-P6-0
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded
Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.

15

®

PASSPORT PD-150
(This is the model name for warranty claims)

.PARTS LIST:
QTY

PART #

PACKING MATERIALS

DESCRIPTION

REFERENCE DESIGNATION

2 REF

PE FOAM-SIDE EFPAPD150+05CS17

1 0699000000

MICROPHONE P51 FENDER

1 REF

CLIP-MIC 2617A

1 REF

LEATHER BAG 2617A

2 0070587000

SPK CABLE MONO 90 ANGLE PLUG L=30FT

1 REF

CABLE-RCA STEREO 2P L=610

1 REF

**SJT #18 /3C 2M BLK POWER CORD 1-51-438

PACKING (UL)

1 REF

H05VV-F 0.75MM/3C 2M BLK VDE W 1-51-439

(CE)

1 0074365014

PASSPORT MICROPHONE CABLE

.PARTS LIST:
QTY

CASING MATERIALS

PART #

DESCRIPTION

1

REF

HALO BUSHING 0813C

4

REF

METAL WASHER M3X0.5X8MM BZ

PANEL/MTG.BK

3

REF

METAL WASHER M3X0.5X8MM BZ

PANEL/PARTIT

3

REF

METAL WASHER M3X0.5X8MM BZ

PANEL/SMPS

2

REF

WASHER SPRING M3X0.9X5.5 BZ

FUSE COVER

6

REF

WASHER SPRING M3X0.9X5.5 BZ

REAR PANEL

2

REF

SCREW FLAT-CS M3X 5 MM B Z CROSS

HANDLE COVER

2

REF

ME 4*16 6.8MM BK/RH

HANDLE/CONSO

2

REF

SCREW TAP-BT BH M2.6X 6 MM BZ CROSS

8

REF

TTS SCREW M2.6x8 BH BZ

2

REF

SCREW D3X6 S-TITE BH,BK

FUSE COVER

3

REF

SCREW D3X6 S-TITE BH,BK

PANEL/SMPS

6

REF

SCREW D3X6 S-TITE BH,BK

REAR PANEL

3

REF

SCREW D3X6 S-TITE BH,BK

SIDE PLATE-A

3

REF

SCREW D3X6 S-TITE BH,BK

SIDE PLATE-B

2

REF

S-TITE 3X8 (BLK)

HINGE

4

REF

S-TITE 3X8 (BLK)

PANEL/MTG.BK

3

REF

S-TITE 3X8 (BLK)

PANEL/PARTIT

2

REF

SCREW B-TITE BIND HEAD M3X8 CROSSRECESS BZ

PANEL/PARTIT

4

REF

B-TITE 3X10MM (BLK.ZN)

HANDLE BKT

8

REF

SCREW TAP-C2 BH M4X 10 M M BZ CROSS

FOOT STAND

6

REF

SCREW B-TITE BIND M4X14 CS-RECESS BZ

SUPPORT RIB

1

REF

COVER-TOP EFPAPD150+05CS17

*
shaded
shaded + *
**
shaded + **

REFERENCE DESIGNATION

JH1303-01

DOOR

Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
Unique Fender® part. Order directly from the FMIC Parts Department.
Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
Both a unique Fender® part and a Safety Requirement part as defined above.

16

®

PASSPORT PD-150
(This is the model name for warranty claims)

.PARTS LIST:
QTY

CASING MATERIALS

PART #

DESCRIPTION

1

REF

PANEL-REAR SECC EFPAP150D+05CS11

1

REF

PLATE-SIDE EFPAPD150+05CS17

1

REF

SIDE PLATE-B 4132-4881-1

1

REF

BKT-SOCKET 4132-4891-0 P150

2

REF

HANDLE BKT 4132-4901-1 P150

1

REF

COMPRESSION SPRING 2751-6-0

1

REF

COVER-10P SK 4132-5131-0

1

0070568000

COVER-HANDLE TOP EF010C

2

REF

CONSOLE MAIN EF010C

2

REF

FOOT STAND BOTTOM EF010C

1

REF

SUPPORT RIB BOTTOM EF010C

1

0070570000

DOOR 1464-3700-1 P150

1

0070571000

LOCKER-DOOR 1464-3800-0 P150

2

REF

HINGE 1464-4200-0 P150

2

REF

BADGE-SPRUE CAP EFPAPD150+05CS17

1

REF

GASKET HANDLE PD150

1

REF

GASKET TOP PD150

1

REF

GASKET BOTTOM PD150

1

REF

BADGE EFPAP150D+05CS11

1

REF

WIRE-CONN 2P #20 UL1007 L=70 RINGTERMINAL

.PARTS LIST:
QTY

REFERENCE DESIGNATION

DESCRIPTION

8

REF

WASHER METAL M4X0.8X10 BZ

8

REF

SPRING WASHER M4X0.8X6.5 MM BZ

8

REF

SCREW S-TITE 4X16 PH BLK ZINC

8

REF

C-PIN 4132-4691-0 P-150

4

REF

LATCH BKT 4132-4681-0

4

REF

TORSION SPRING-LATCH 2751-5-0

4

0070564000

LATCH 1464-3500-0 P150

4

REF

LOCKER-LATCH 1464-3600-1 P150

QTY
8

CONSOLE

LATCH LOCKER CASING MATERIALS

PART #

.PARTS LIST:

CN606

REFERENCE DESIGNATION

P-150

MIXER CASING MATERIALS

PART #

DESCRIPTION

REFERENCE DESIGNATION

REF

WASHER METAL M3X0.3X4 WZ

MIX/RCA

*
shaded
shaded + *
**
shaded + **

Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
Unique Fender® part. Order directly from the FMIC Parts Department.
Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
Both a unique Fender® part and a Safety Requirement part as defined above.

17

®

PASSPORT PD-150
(This is the model name for warranty claims)

.PARTS LIST:
QTY

MIXER CASING MATERIALS

PART #

DESCRIPTION

REFERENCE DESIGNATION

2

REF

FIBRE WASHER M3X0.8X8MM

MIXER PCB

6

REF

S-TITE 3X8 (BLK)

MIC JACK

1

REF

SCREW B-TITE BIND HEAD M3X8 CROSSRECESS BZ

LED PCB

8

REF

SCREW B-TITE BIND HEAD M3X8 CROSSRECESS BZ

MIXER PCB

2

REF

SCREW B-TITE BIND HEAD M3X8 CROSSRECESS BZ

RCA JACK

4

REF

SCREW B-TITE BIND HEAD M3X8 CROSSRECESS BZ

U-BAR

4

REF

SW COVER 2751-11-0

SW-SLIDE

1

REF

SHIELD PLATE 4132-4741-0 P150

1

REF

MIC JACK BKT 2751-9-0

7

REF

WASHER M13 4132-5041-0

PHONE JACK

7

REF

T-NUT M12 4132-5031-0

PHONE JACK

1

REF

FRONT PANEL

2

0070536000

KNOB A 1463-8301-1 P150

KNOB MASTER

20

0070537000

KNOB B 1463-8401-1 P150

KNOB SMALL

2

REF

U-BAR

1

REF

SHEET FRONT PD150

.PARTS LIST:
QTY

FRONT PANEL

POWER AMP CASING MATERIALS

PART #

DESCRIPTION

1

REF

SHIELD COVER CONNECTOR 26.4X49.3 SECC

1

REF

CC 1KV 1000PF 10% RL Y5P 5X5

C229

1

REF

CC 1KV 1000PF 10% RL Y5P 5X5

C230

4

REF

METAL WASHER M3X0.5X8MM BZ

2SK1058/J162

1

REF

WASHER SPRING M3X0.9X5.5 BZ

HEAT SINK

6

REF

WASHER SPRING M3X0.9X5.5 BZ

REAR PANEL

2

REF

SCREW MACHINE PAN M3X10 CROSSRECESS BZ

H.S/BRASS

2

REF

SCREW BH M3X 5 MM BZ CRO SS

PCB/BRASS

2

REF

SCREW BH M3X 14 MM BZ CR OSS

fuse cover

4

REF

SCREW TAP-BT BH M2.6X 6 MM BZ CROSS

FUSE HOLDER

6

REF

SCREW D3X6 S-TITE BH,BK

REAR PANEL

4

REF

SCREW B-TITE PH M3X 12 M M YZ CROSS W/
WASHER

2SK1058/J162

4

REF

SCREW B-TITE PH M3X 12 M M YZ CROSS W/
WASHER

MTG. BKT

1

REF

SCREW B-TITE PH M3X 12 M M YZ CROSS W/
WASHER

TH/SW BKT

*
shaded
shaded + *
**
shaded + **

REFERENCE DESIGNATION

Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
Unique Fender® part. Order directly from the FMIC Parts Department.
Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
Both a unique Fender® part and a Safety Requirement part as defined above.

18

®

PASSPORT PD-150
(This is the model name for warranty claims)

.PARTS LIST:
QTY

POWER AMP CASING MATERIALS

PART #

DESCRIPTION

REFERENCE DESIGNATION

11

REF

SCREW B-TITE BIND HEAD M3X8 CROSSRECESS BZ

HEAT SINK

4

REF

MICA T-400 T03P 25X20M TO-3P

2SK1058/J162

2

REF

ANTENNA WASHER

HEAT SINK

2

REF

2666-12 METAL WASHER M12 X0.5X16MM NI

PHONE JACK

2

REF

2666-11 HEXAGON NUT M12

PHONE JACK

1

REF

2688-15-0 TH/SW BKT

HEAT SINK

2

REF

MTG. BKT 4312-4711-0 P150

HEAT SINK

2

REF

BRASS TUBE 2751-10-0 L=9mm

PCB/H.S

2

REF

1800-FI GM FUSE HOLDER

1

REF

TR FET 2SK1058-E HITACH IDS=7A

Q204

1

REF

TR FET 2SK1058-E HITACH IDS=7A

Q208

1

REF

TR FET 2SJ162-E HITACH IDS=7A

Q205

1

REF

TR FET 2SJ162-E HITACH IDS=7A

Q209

1

REF

HEAT SINK PD150 ROK

2SK1058/J16

1

REF

CN ASSY UL1007 PCE98-033 3 #18
L=90/150/170 4P

CN202

.PARTS LIST:
QTY

REG CASING MATERIALS

PART #

DESCRIPTION

1

REF

2617-12 REV:A WIRELESS PCB

1

REF

T'NAL 2225A-20D 2x10 PIN NELTRON 3.96mm
CARD EDGE

CN606

3

REF

METAL WASHER M3X0.5X8MM BZ

U601 PCB

3

REF

WASHER SPRING M3X0.9X5.5 YZ

U601 PCB

1

REF

M3 NUT NI

U601

2

REF

SCREW MACHINE PAN M3X12 CROSS-RECESS
BZ

CN606

3

REF

SCREW M3X10 (BLK)

REG PCB

1

REF

MICA T-400 T03P 25X20M TO-3P

U601

2

REF

ANT WIRE 2751-13-0

CN603

1

REF

BUSHING TO-220A

U601

1

REF

SPONGE BAR 2751-12-0

CONSOLE

2

REF

RUBBER CABLE BUSHING BLK 6MM

SIDE PLATE-

1

REF

UL1533#26 G/B PCE99-0228 L=253MM 8 POS
HOUSING

CN607A

1

REF

UL1533#26 G/B PCE99-0229 L=60MM 8 POS
HOUSING

CN607B

1

REF

UL1007#26 R/B PCE99-0200 L=280MM 2 POS
HOUSING

CN601

*
shaded
shaded + *
**
shaded + **

REFERENCE DESIGNATION

Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
Unique Fender® part. Order directly from the FMIC Parts Department.
Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
Both a unique Fender® part and a Safety Requirement part as defined above.

19

®

PASSPORT PD-150
(This is the model name for warranty claims)

.PARTS LIST:
QTY

SMPS CASING MATERIALS

PART #

DESCRIPTION

REFERENCE DESIGNATION

1

REF

CHOKE EARTH 85UH 300V #16 WIRE GRE/YEL

L304

1

REF

FERRITE BEAD 26430000101 (FAIR-RITE)

FB303/Q301

1

REF

FERRITE BEAD 26430000101 (FAIR-RITE)

FB304/Q301

1

REF

FERRITE BEAD 26430000101 (FAIR-RITE)

FB305/Q302

1

REF

FERRITE BEAD 26430000101 (FAIR-RITE)

FB306/Q302

1

REF

FERRITE BEAD 26430000101 (FAIR-RITE)

FB307/D308

1

REF

FERRITE BEAD 26430000101 (FAIR-RITE)

FB308/D308

1

REF

FERRITE BEAD 26430000101 (FAIR-RITE)

FB309/D309

1

REF

FERRITE BEAD 26430000101 (FAIR-RITE)

FB310/D309

4

REF

METAL WASHER M3X0.5X8MM BZ

FAN

1

REF

WASHER METAL M4X0.8X10 BZ

SPACER

1

REF

WASHER INT-TOOTH M4X0.8X8.5 BZ

KS-966N-1

1

REF

WASHER INT-TOOTH M4X0.8X8.5 BZ

RING T'NAL

4

REF

WASHER SPRING M3X0.9X5.5 BZ

FAN

2

REF

WASHER SPRING M3X0.9X5.5 BZ

POWER INLET

1

REF

WASHER SPRING M4X1X7 NI

KS-966N-1

1

REF

WASHER SPRING M4X1X7 NI

RING T'NAL

2

REF

M3 NUT NI

POWER INLET

1

REF

NUT HEX M4

KS-966N-1

1

REF

NUT HEX M4

RING T'NAL

2

REF

SCREW MACHINE PAN M3X8 CROSS-RECESS
BZ

AC SELECTO

2

REF

SCREW MACHINE PAN M3X8 CROSS-RECESS
BZ

POWER INLET

5

REF

SCREW M3X10 W/S&F WASHER (BLK)

PCB

4

REF

SCREW M3X10 (BLK)

FAN

4

REF

SCREW D3X6 S-TITE BH,BK

TOP COVER

3

REF

SCREW B-TITE BIND M4X8 CROSS-RECESS
BZ

SPACER

1

REF

ANTENNA WASHER

PCB/GND

1

REF

RING T'NAL 04RNB14-5

1

REF

COVER-TOP POWER SUPPLY PD150 PLUS

1

REF

BOTTOM COVER 4132-4732-0 P150

1

REF

BUSHING OSB-10

1

REF

SPACER SSRS4-5-01 P150

1

REF

**POWER INLET SOCKET SC9F-21

2

0070483000

**FUSE S505-4A TIME DELAY 250V 5x20mm
UL/CSA/SEMKO

POWER INLET

1

0070267000

**SWITCH ROCKER 2PIT

SW301

1

BOTTOM COVER

REF
CN ASSY UL1007 #18 L=280 2P F P3.96 11T
CN201
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded
Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.

20

®

PASSPORT PD-150
(This is the model name for warranty claims)

.PARTS LIST:
QTY

SMPS CASING MATERIALS

PART #

DESCRIPTION

REFERENCE DESIGNATION

1

REF

CN ASSY UL1007 #18 L=300 4P F P3.96 11T

CN203

1

REF

CN ASSY UL1007 #18 L=180 2P M P3.68 11T

CN7

1

REF

WIRE-CONN 3P P3.96 #18 UL1015 L=45 F/M

CN301

1

0070261000

**DC FAN CHA8012BS

.PARTS LIST:
QTY

SPEAKER ASSY

PART #

DESCRIPTION

0070376000
2

SPEAKER BOX QUICK REPAIR MODULE

REF
2

CE 100V 33u 20% AL 16X42 BI-POLAR
BO3A(AXIAL)

2

0070067000

REAR PHONE JACK 5 PIN

2

REF

WASHER METAL M9X0.5X14 BZ

8

REF

SCREW BH M6X 25 MM BZ CROSS

REF

SCREW B-TITE FLAT-CS M3X 10 CS-RECESS
BZ

24

REF

SCREW TAP-C2 BH M4X 10 MM BZ CROSS

2

REF

SCREW B-TITE BIND M4X14 CS-RECESS BZ

2

REF

QC ACC LABEL

2

0070552000

GRILLE 4132-4781-0 P150

1

REF

O RING 4152-2091-0 NK110C

2

REF

BADGE-SPRUE CAP EFPAPD150+05CS17

2

REF

GASKET SPEAKER 2751-7-A L=1080mm

2

REF

SPRUE CAP(RED)

2

REF

SPEAKER BOX MAIN EF010C

SPK BOX

2

0070301000

STAND PLUG BOTTOM EF010C

BACK

2

REF

PLASTIC CABLE TIE 97MM

WIRE

REF

SPEAKER WIRE 200MM BLK-B LK-RED 1-50276

SPK

4

0070370000

PD150 2.75 INCH TWEETER

2

0070371000

PD150 WOOFER

4

2

*
shaded
shaded + *
**
shaded + **

REFERENCE DESIGNATION

PHONE JACK

SPK

Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
Unique Fender® part. Order directly from the FMIC Parts Department.
Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
Both a unique Fender® part and a Safety Requirement part as defined above.

21

®

PASSPORT PD-150
(This is the model name for warranty claims)

.PARTS LIST: MISCELLANEOUS MATERIALS
QTY

PART #

1

0070377000

TOWER SIDE CABINETS A, PD150

1

0070377000

TOWER SIDE CABINETS B, PD150

1

0070315000

GP UL/IEC POWER CORD (UL/CSA VER)
NORTH AMERICA,TAIWAN

1

0070316000

GP CE/IEC POWER CORD (EURO VER)
CONT.EUR/ASIA EXPT HK,CHINA, AUSTRALIA,
JAPAN

1

0070317000

GP BS/IEC POWER CORD (UK/HK) UK,HK

1

0070318000

GP CCEE POWER CORD (CHINA) GREAT
WALL STD.

1

0070319000

GP SAA/IEC POWER CORD (AUST/NZ) AUSTRALIA/NEW ZEALAND

1

0070320000

GP JIS/IEC POWER CORD W/ GND PIN JAPAN

*
shaded
shaded + *
**
shaded + **

DESCRIPTION

REFERENCE DESIGNATION

Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
Unique Fender® part. Order directly from the FMIC Parts Department.
Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
Both a unique Fender® part and a Safety Requirement part as defined above.

22

®

PASSPORT PD-150
(This is the model name for warranty claims)

Service Diagram List
Service Diagram (Schematic) ............ MIXER
Service Diagram (PCB Assembly) ............ MIXER PCB
Service Diagram (Schematic) ............ RCA/XLR INPUT
Service Diagram (PCB Assembly) ............ RCA/XLR INPUT PCB
Service Diagram (Schematic) ............ DSP REVERB
Service Diagram (PCB Assembly) ............ DSP REVERB/ LED PCB
Service Diagram (Schematic) ............ SMPS
Service Diagram (PCB Assembly) ............ SMPS PCB
Service Diagram (Schematic) ............ POWER AMPLIFIER
Service Diagram (PCB Assembly) ............ POWER AMPLIFIER PCB
Service Diagram (Test Point Information) ........... TP1-TP24
Service Diagram (Block Diagram) ............ WIRING DIAGRAM
Service Diagram (Exploded View) ............ MAIN UNIT ASSY
Service Diagram (Exploded View) ............ MIXER ASSY
Service Diagram (Exploded View) ............ LATCH ASSY
Service Diagram (Exploded View) ............ SPEAKER ASSY
Service Diagram (Exploded View) ............ TOWER HOUSING ASSY
Service Diagram (Exploded View) ............ PACKING ASSY

TP12

TO
RCA
PRE
AMP

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15

CN1
CON15

TP11

11

12

2
1

8
7
4
5
1

1
5
4
7
8

R44
1k

R43
1k

R65
10k

2

MONO
3

R66
10k

PJ6-09-5

STEREO

PJ4

R48
82K

R47
82K

PJ6-09-5

LINE 3

PJ3

10

9

8

7

6

R26
1k

R25
1k

1
2

6

5

5

STEREO

2

3
0dB

R30
1k

R50
33k

3
0dB

+30dB
1

C24
2u2/50V

+15V

R31
33k

+30dB

C14
2u2/50V

C13
2u2/50V

+15V

+30dB

-15V

R52
33k

5

6

INPUT GROUND

D14
1N4148

R68
27k

+15V

3

2

-15V

-15V

+15V

U6A
TL072

2

3

C37
27p
1

VR14A
100KB

U6B
TL072

7

-15V

3

VR15B
100KB W/CC

EQ/HI

C40
1u/50V

VR15A
100KB W/CC

EQ/HI

C39
1u/50V

C28
0.47u/50V

C17
0.47u/50V

VIP

R11
10K

C6
1u/50V

C5
0.47u/50V

+15V

R140
3R3 2W

C38
27p

LEVEL/STEREO
VR14B
100KB
6
4
5

1

LEVEL/STEREO

D12
1N4148

C26
100p

R51
33k

U3B
LM833
7

-15V

D8
1N4148

D10
1N4148

+15V

R32
33k

C16
100p

-15V

U3A
LM833
1

+15V

-15V

D4
1N4148

D6
1N4148

D11
1N4148

6

5

D9
1N4148

-15V

R8
33k

C4
100p

-15V

U1A
LM833
1

D2
1N4148

+15V

D7
1N4148

2

3

D5
1N4148

-15V

D3
1N4148

2

3

D1
1N4148

R7
33k

D13
1N4148

R67
27k

C27
100p

+30dB

C25
2u2/50V

-15V

C35
1u/50V

6

C36
1u/50V

R46
1k

0dB

SS2214RG9
SW3B
4

R49
33k

6 0dB
C15
100p

+15V

C1
2u2/50V

C2
2u2/50V

0dB

C3
100p

SS2214RG9
SW2B
4

R29
33k

R28
33k

SS2214RG9
SW3A

2

SW4
SS2214RG9

1

R6
1k

5

R5
33k

0dB

SS2214RG9
SW1B
4

R4
33k

3

+30dB
1

SS2214RG9
SW2A 1 +30dB

2

SS2214RG9
SW1A

R45
1k

R64
10k

R63
10k

R27
1k

CN604B
WE2

CN605B

1
5
4
7
8

1
5
4
7
8

R3
1k

R1
1k

R2
1k

WF2
TO WIRE DOCKING

LINE 2

PJ2 PJ6-09-5

4
5

TO WIRE DOCKING

LINE 1

PJ1 PJ6-09-5

1

3

2

13

4

6

1

3

1

5

6

1

1

3

1

1

C42
223

R55
82k

1

C44
223

R141
39k

2

1
2

4

CN7
CON2

R142
39k

5

R74
27k

R73
27k

C32 27p

C31 102
1n

C47
47u/25V

R56
39k

TO START GROUND

R72
27k

6

EQ/LOW
VR16B
100KB W/CC

R71
27k

3

C20 102
1n

7

5

6

+15V

3

2

-15V

7

1

R19
1M

R18
1M

2

1

3

U5B
TL072

5

6

3

1

6

4

2

VR22A
100KB

R80
10k

BAL

3

1

5

1

3

S

D

G

R76
100k

2

2

R79
100k

R81
82k

VR17B
100KB W/CC

1

PAN

PAN

PAN

4

R20
100k

2

R78
82k

R77
82k

R40
82k

R24
470

R60
82k

R41
82k

R59
100k

R127
82k

R121
6k8

R128
82k

5

6

3

R126
82k

R125
82k

C75
0.47u/50V

R129
10k

U8B
TL072

+15V

7

R89
1k

R88
1k

R130
39k

2
1

3

+15V

U12A
TL072

-15V

R122
100k

NC

VR21A
100KB

+15V

1

VR START = VR1
VR END = VR22

D START = D1
D END = D16

U START = U1
U END = U12

R START = R1
R END = R145

C START = C1
C END = C87

5
4
3
2
1

5

6

CN2 CN2
CON5 WF5

5
4
3
2
1

R123
39k

PINS 2/5 SHORTED TO 3/6

Q START = Q1
Q END = Q11

C78
27p

R90
1k

1
2
3

CN3
CON3

PINS 2/5 SHORTED TO 1/4
PINS 2/5 AT CENTER

MASTER REV

3

2

MAX(CW)

CENTER

MIN(CCW)

R120
110k

R87
100k

1
U8A
TL072

-15V

VR ROTATION CONFIGURATION

C50
0.47u/50V

R84 110k

R85
6k8

2

C49
0.47u/50V

R83
6k8

R86
100k

R82
110k

TP17

LEFT CHANNEL BUS

TP18

R61
82k

VR13A
100KB W/CC

R58
100k

R42
82k

R39
100k

VR13B
100KB W/CC
5

2

R62
82k

6

3

1

R22
470
R23
470

VR9A
100KB W/CC

R38
100k

Q3
J112

5
VR9B
100KB W/CC
6

4

3

1

S

D

VR5B
100KB W/CC
5
R21 100k

VR5A
100KB W/CC

2

Q2
J112

PAN

S

D

G

6

PAN

4

3

PAN

Q1
J112

VR8A
100KB

2

VR4A
100KB

VR17A
100KB W/CC

VR12A
100KB

2

1

3

C34
27p

7

REV/AUX

BAL

2

VR11A
100KB

7

REV/AUX

U4B
TL072

1

G

1

3

C23
27p

C87
103

R17
1M

LEVEL MIC/LINE3

5

6

3

7

C11
27p

REV/AUX

U2B
TL072

1

LEVEL MIC/LINE2
VR7A
100KB

2

VR2A
100KB

D16
1N4148

REV/AUX

R75
10k

U7B
TL072

C46 27p

U7A
TL072

C43
27p

R57
12k

R37
12k

C12
4u7/50V

R15
1k

R16
2M2

5

6

3

LEVEL MIC/LINE1

-15V

R14
12k

Q11
MPSA56

C48
47u/25V

C33
1u/50V

+15V

C22
1u/50V

CN4
CON3

C10
1u/50V

CN4
CON3

27p

C83 102
1n

C21 27p

-15V

R35
82k

EQ/LOW
VR16A
100KB W/CC

U5A
TL072

2

C30
153

C29
152

U4A
TL072

2

EQ
VR10A
100KB W/CC

3

C84
102

C9

R13
39k

R36
39k

R12
82k

D15
1N4148

2

1

C19
153
EQ
VR6A
100KB W/CC

C18
152

U1B
LM833

C45
102
1n

R70
27k

3

U2A
TL072

C41
102
1n

C8
153

EQ
VR1A
100KB W/CC

C7
152

OUTPUT GROUND

5

2

R69
27k

+15V

3

2

-15V

R54
39k

1

R53
12k

+15V

3

2

-15V

R34
39k

R33
12k

2

VR3A
100KB

+15V

3

2

-15V

R10
39k

R9
12k

S

D

REVERB
PCB

GND

REV OUT

+15V

REV IN

FS

7

Q4
J112

U12B
TL072

C79
27p

R124
56k

C56
0.47u/50V

R91
1k

R143
33k

R144
33k

NC

C51
0.47u/50V

1
2
3

CN3
CON3

S

D

S

D

G

5

6

1

G

RIGHT

+15V

U9A
TL072

1

C52
27p

3

7
U9B
TL072

2

R132
1M

S

D

Q9
J112

G

R133
1M

R118
1M

C68
0.47u/50V

R108
1M

C61
0.47u/50V

C73
4u7/50V

R119
2M2

R117
2M2

C66
4u7/50V

C58
0.47u/50V

S

D

C82
1u/50V

1
2
3
TP2

C72
1u/50V

R134
1M

5

6

TP1

5

C86
104

+15V

R113
6k8

CN8
WF8

R106
6k8

R115
6k8

5

6

7

R111
39k

R104
3k3

R138
10k

R137
10k

R136
470

C85
104

TO RIGHT PA

1
2
3

CN5
CON3

TO LEFT PA

8
7
4
5
1

PJ6-09-3

-15V

POWER IN

CN6
+15V CON2

1
2

PJ7
PJ6-09-3

FOOT
SWITCH

PJ6
PJ6-09-5
AUX RET
STEREO

AUX SEND
MONO

PJ5

C77
47u/50V

5
4
1

5
4
1

TP16
C74
222

R116
12k

GND

C67
222

AUDIO OUT

TP15
R105
12k

TP20

-15V

R145
100k

R114
3k3

R112
12k

R139
100k

C62
27p

R102
12k

U11B
TL072

C76
47u/50V

R135
1M

C71
0.56u/50V

C70
222

1
U11A
TL072

R101
39k

C63
222

C81
27p

C64
0.56u/50V

C69
27p

+15V

3

2

-15V

C80
27p

R95
100k

R94
33k

R98
33k

R99
100k

+15V

7

1
U10A
TL072

-15V

C55
472

U10B
TL072

C60
472

R103
6k8

6

3

2

3

TP19

Q10
J112

G

-15V

2

VR20B
100KB W/CC

C59
472

Q7
MPSA56

Q5
MPSA56

C65
1u/50V

R110
39k

-15V

R100
39k

R96
33k

4
SYSTEM EQ

R97
100k

C54
472
VR20A
100KB W/CC

R93
33k

1
SYSTEM EQ

R92
100k

TP13

C53
0.47u/50V

TP14

VR19A
100KB W/CC
3

R109
2M2

Q8
J112

G

Q6
J112

1

R107
2M2

C57
27p

3

2

-15V

2

LEFT
VR18A
100KB W/CC

4
8

8
4
8

1
2
3
1
2
3

4

AUX CHANNEL BUS

4
8
4
8
4
8

4
4
8

RIGHT CHANNEL BUS

4
8

14

4
8

4
8

8
4
8

1

PASSPORT

Mixer Schematic Diagram

PASSPORT

Mixer Section PCB Component Side

Mixer Section PCB
2

PASSPORT

Mixer PCB Copper Side

Mixer Section PCB
3

RJ1A
RCA HSP-206V-03

L

14

TAPE OUT

15
13

RJ1B
RCA HSP-206V-03

R
2

MJ1

2
MIC 1
SVP561P-R

+
G

3

-

3

1

1

CN1
WF15
4

MJ2

2
MIC 2
SVP561P-R

+
G

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15

-

3

5

1

TO
MIX
AMP

6

MJ3

2
MIC 3
SVP561P-R

+
G

-

3

7
8

1

RJ1C
RCA HSP-206V-03

9

EXTRA MUSIC
10
RJ1D
RCA HSP-206V-03

RJ1E
RCA HSP-206V-03

12
L

RJ1F
RCA HSP-206V-03

11

PASSPORT

R

RCA Pre Amp Schematic Diagram
4

1u
50V

C602

240

1k5

IN
O
ADJ

R601

LM317HV

U601

R602

CN602
PWR/OUT

CN601
PWR/IN

C601
100n
C603
1000u/63V

REG PCB Component Side

C602

1u
50V

LM317HV

1k5
R601

C603
1000u/63V

U601
C601
100n

R602

CN601
PWR/IN

240

CN602
PWR/OUT

IN
O
ADJ

REG PCB Copper Side

RCA/XLR Input PCB Component Side

RCA/XLR Input PCB Copper Side

PASSPORT
RCA/XLR/REG PCB
5

PASSPORT

Reverb Schematic Diagram

C429
47uF/25V

6PIN

C431
0.1uF

C428
47uF/25V

CN401
AUDIO OUT
6
AGND
5
AUDIO IN
4
+15V
3
AGND
2
-15V
1

1

C432
0.1uF
0.1uF

C424

0.1uF

C422

C430
10uF/25V

R401
100K

10uF/25V

C401
+

-

+

2.2K

R402

R417
1K

C425

NJM2068
0.1uF

0.1uF

C423

1

U401C

2

3

U401A
NJM2068

NJM2068

U402A

3

8
4

-

+

0.1uF

C427

NJM2068

C426

5

6

R411
10K

R410
10K

220R

R407

-15V

NJM2068 CON2

2
1

CN402
3

C408

C404
4700pF

220R

R406

TP21

10uF/25V

C402

U403C

+15V

C403
10uF/25V

NJM2068
C409
220pF

0.1uF

7

1

7

220pF

R409
4.7K

U402B

C407

NJM2068

+

-

2.2K
U403A

R405

2.2K

R404

NJM2068

+

-

U402C

3

2

5

6

2.2K
U403B

8
4

2

8
4

R403

Vin

U407
78L05

1
2
3
4
5
6
7
8

C413
0.1uF

C412
0.1uF

10uF/25V

C433

C411
10uF/25V

+5V

R419
10K

R416
10K

1
2
3
4
5
6
7
8

1
2
3
4
5
6
7
8

AL1101 ADC

INL+
INLAGND
REF+
REFVD
DGND
FORMAT

U404

+5V

XL401
12.288MHz

C410
10uF/25V

R418
10K

1

R413
220

C434
0.1uF

Vout

R420
10K

R421
10K

TP22

R412
4.7K

470pF

C406
0.1uF

C405
0.1uF

TP23

+5V
R408
1K

GND
2

6

AL1201 DAC

OUTLOUTL+
AGND
REF+
REFVD
DIN
FORMAT

U405

AL3201B

Dig Out
Int/Ext
Xtal In
Xtal Out
Prog0/SData
Prog1/SClk
Prog2
Prog3

U406

INR+
INRMID
VA
AGND
DGND
DOUT
WDCLK

OUTROUTR+
MID
VA
AGND
DGND
DEM
WDCLK

TP24

DigIn
Vdd
Bypass
Gnd
Reset
SysClk
BitClk
WordClk

16
15
14
13
12
11
10
9

16
15
14
13
12
11
10
9

16
15
14
13
12
11
10
9

+5V

+5V

C414
0.1uF

C418
0.1uF

C416
0.1uF

C415
0.1uF

C419
0.1uF

C420
1uF/50V

C417
0.1uF

R414
10R

+5V

R415
10K

Reverb PCB Component Side

Reverb PCB Copper Side

04/98

GR/RED
2751-6 LED

CN205

04/98
CN205

LED201
DUAL LED

REV:D

REV:D

LED201
DUAL LED

GR/RED
2751-6 LED

LED PCB Copper Side

LED PCB Component Side

PASSPORT
Reverb Section / LED PCB
7

PASSPORT

SMPS Schematic Diagram

F301
T4A 250V

SW 2P2T

SW301

CN301B
CON3

CN301A
WF3

C301

470K 1/2W
220n 275V ac

C302 220n 275V ac

R301

L

4

6

1000P 400V

1000P 400V
C327
C326

3

1

L303

FB302
FB

C309
10u/50V

J301
PLUG AC MALE

NTC START END=NTC301

G START END=G301

TP START END=TP301

D303
1N4148

R305
1M

C310
100n

D304
1N4148

100K

R304

C308
470p

C307
100u/50V

KSF1689

D302
UF 4003

C306
330u/200V

N

EPCOS 2X15mH

T305

FB

FB301
C305
330u/200V
SW302
AC SELECTOR SW
220V
110V

T307
EPCOS 2X15mH

1000P 400V
1000P 400V
C324
C325

D301
KBU6J

16
15

NTC301
SCK055

GAS ARRESTER

2

1
VFB

R307
22K

680

R306

ISEN

U301
3842

4

C316
100n
1

T302
KS-851N

TP1

D305
1N4148

COMP

R303
100K 1/2W

R302
100K 1/2W

VREF
8

O/P

7
VCC

6

C311
100n

C312
103

C313
472

RT/CT
4

G301

GND
5

3
2
1

1
2
3

E

3

R308
1K

R309
3K9

C314
222

R310
470

C315
472

5

R314
6 51

7

8

R312
51

Z301
18V

Z302
18V

FB305
FB

Z303
18V

4

G

Q302
IRF840

G

U302
CNY17-2

L START = L301
L END = L303
5

Z START = Z301
Z END = Z305

D START = D301
D END = D309

C START = C301
C END = C327

R START = R301
R END = R325

R311
220

R315
1K

R313
1K

Z304
18V

FB303
FB

R316
0.22 3W

S

D

D306
UF 4006

FB304
FB

2

1

U START = U301
U END = U303

FB START = FB301
FB END = FB302

T START = T301
T END = T306

FB306
FB

Q301
IRF840

S

D

Z305
12V

CN603B
CON2

D307 C317
UF 4006 100p 1KV

12

9

R317
100 2W

1
2

8

7

3

2

4

2
1
RF1
ANTENNA

CN7
CON2

CN201 2
CON2 1

C319
470p 1KV

R319
47 2W

FB

FB309

R318
47 2W

R322
470

R321
39K

FB310
FB

D309
FEP 16GT

D308
C318
FEP 16GT
470p 1KV

TO WIRE DOCKING

NC

NC 1

T303
KSF1689

FB307
FB

KS-1554
360uH

C321
10000u/63V

C320
10000u/63V
FB308
FB

KS-1554
L302
360uH

R
U303
TL431

R323
47K

C323
1u/50V

2K 1W

R320

CHASSIS START
GROUND GROUND

K
A

8

1
2
3
4

CN203
CON4

TP3

TO
POWER
AMP

R325
2K7

TP301
TP1K

R324
47K

TP2

SMPS PCB Component Side

SMPS PCB Copper Side

PASSPORT
SMPS PCB
9

AUDIO IN

3
2
1

CN5
WF3

L

R

R205
10K

R228
100K

C212
1u/50V

R227
10K

TP5

D

5

6

Q206
J112

R207
390

3

2

R229
390

TP4

R206
100K

C202
1u/50V

D

Q202
J112
S

+15V

C213
47p

R230
39K

G

1

LO-PA GND

U201B
TL072

7

U201A
TL072

-15V

C203
47p

R208
39K

G

D201
1N4148

R202
2M2

2
1

3

C214
22u/16V

R231
5K1 1%

R233
4K7

3

2

R211
4K7
TP201
1 NV26TLI 1K

C204
22u/16V

R209
5K1 1%

TP202
NV26TLI 1K

2

3

R201
39K

+

_

3

2
1

C205
47p

R212
1K5

R236
3R3 2W

C215
47p

R203
39K

C216
220n

R235
3R3 2W

C206
220n

R213
3R3 2W

Q201
MPSA06

U202A
LM833

R234
1K5

U203A
LM833

1

R232
1K5

+

_

R210
1K5

-15V

S

R240
15K

R239
390

S

R238
390

R237
15K

R217
15K

R216
390

R215
390

R214
15K

Z201
33V

G

Q207
J112 D

R241
56K

D202
1N4148

R218
56K

D

G

Q203
J112

85C

1
2
R242
100K

D207
1N4148

D208
1N4148

R219
100K

D203
1N4148

CN206
CON2

R243
1M

R220
1M

R204
39K

TH201
17AM203A5-4
THERMAL SWITCH

C217
1u/50V

R244
1M

D209
1N4148

C207
1u/50V
6

5
_

+

U202B
LM833

C209
224

_

+

U203B
LM833

6

5

-15V BOOTSTRAP

C218
223

R245
3M3

C219
224

+15V BOOTSTRAP

-15V BOOTSTRAP

C208
223

R222
3M3

HI-PA GND

R221
1M

D204
1N4148

+15V BOOTSTRAP

4

8

4

8

R223
390K

R246
390K

7

7

Z205
15V

Z204
15V

Z203
15V

Z202
15V

D211
1N4148

C221
47u/25V

R248
3M3

C220
47u/25V

D210
1N4148

D206
1N4148

C211
47u/25V

G

G

D

S

S

D

D

S

S

D

R249
3K3 2W

G

G

R247
3K3 2W

R226
3K3 2W

R225
3M3

C210
47u/25V

D205
1N4148

R224
3K3 2W

Q209
2SJ162

Q208
2SK1058

Q205
2SJ162

Q204
2SK1058

R252
270 5W

TP10

R250
1K

C225
100n

C224
100n

TP8

TP6

R

G

R251
2K

2751-6
LED PCB

C227
10u/100V

C602
100n

3

LED201
209EGW

LED

CN205B
CON2

CN205A
WF2

Z207
15V 1W

Z206
15V 1W

+15V

-15V

+42V

CN204A
WF2

1
2

C223
47u/25V

2
1
CN602B
WF2

2
1

CN201
WF2

+15V

-15V

-36V
+36V
EXIT/DC

1
2
3
4

CN202
WF4

CN204B
CON2(FAN)

F202
10A

F201
10A

TO WIRE DOCKING

(OPTION)

4
3
2
1

CN203
WF4

C601
1u/50V

R601
50

START GROUND

R602
240

C222
47u/25V

START GROUND

-42V

START GROUND

2751-6
REG PCB

R603
1K5

U601
LM317HV

Vout

2

PJ202 PJ6-09-3

L SPKR OUT

START GROUND

TP9

LED START END = LED201

TH START END = TH201

F START = F201
F END = F202

TP START = TP201
TP END = TP202

PJ201 PJ6-09-3

R SPKR OUT

R254
270 5W

C228
Z208
47u/25V 12V 1W

Vin

1
4
5

1
4
5

Z START = Z201
Z END = Z208

C603
1000u/63V

R253
330 5W

CN601A
WF2

C226
10u/100V

CN601B
CON2

TP7

D START = D201
D END = D211

U START = U201
U END = U601

R START = R201
R END = R603

C START = C201
C END = C603

ADJ
1

C201
2u2/50V

+15V

2
1

Q START = Q201
Q END = Q209

CN6
WF2

1
2

TO MIXER AMP

2
1

2
1
2
1
2
1

S

10

PASSPORT

Power Amp Schematic Diagram

Amplifier PCB Component Side

Amplifier PCB Copper Side

PASSPORT
Power Amp Section PCB
11

TP1

DC 300V

TP2

DC 42V

TP3

DC -42V

TP4

TP5

PASSPORT
Test Point Information
12

TP6

TP7

TP8

DC 42V

TP9

DC 8V

TP10

DC 15V

PASSPORT
Test Point Information
13

TP11

TP12

TP13

PASSPORT
Test Point Information
14

TP14

TP15

TP16

PASSPORT
Test Point Information
15

TP17

TP18

TP19

DC 15V

TP20

DC -15V

TP21

DC 15V

TP22

DC 5V

PASSPORT
Test Point Information
16

TP23

TP24

PASSPORT
Test Point Information
17

Wiring Diagram

18

CN203

AMP PCB

AF_CH1
GND
GND
VCC
GND
AF_CH2

CN5

CN6

GND
AUT_CH2

balck

red

CN205

CN201

CN205

FAN

CN204

04/98

REV:D

CN601
PWR/IN

AUT_CH1
GND
white
black

LED PCB

1k5

LED201
DUAL LED

GR/RED
2751-6 LED

C603
1000u/63V

CN601

C602

240

R601
1u
50V

C601
100n

R602

CN602

REG
PCB

SMPS PCB

CN602
PWR/OUT

U601

IN
O
ADJ

LM317HV

CN205

PASSPORT

Reverb
PCB

CN402

MIXER PCB

CN5

CN6

RCA/XLR
Input PCB

CN7

CN2

CN1

CN401

CN605B CN604B

CN1

The following is the legend of the mating connections
PCB-P150D11+MIXE
1
GND
2
MIC1+
3
MIC14
MIC2+
5
MIC26
MIC3+
7
MIC3CN1
8
GND
9
RCA IN1
10
RCA IN2
11
STEREO R
12
STEREO L
13
TAPE OUT R
14
TAPE OUT L
15
GND
PCB-P150D11+MIXE
1 GND
2 +15V
CN2
3 REV OUT
4 REV IN
5 FS
PCB-P150D11+MIXE
1 AUDIO OUT L
CN5
2 GND
3 AUDIO OUT R
PCB-P150D11+MIXE
CN6
1 -15V
2 +15V
PCB-P150D11+MIXE
CN7
1 GND
2 GND
PCB-P150D11+MIXE
CN604B
1 AF_CH1
2 GND
PCB-P150D11+MIXE
CN605B
1 AF_CH2
2 GND
PCB-P150D11+PWAM
CN205
1 GND
2 +15V
PCB-P150D11+PWAM
CN601
1 +42V
2 GND
PCB-P150D11+SMPS
CN201
1 GND
2 GND
PCB-P150D11+SMPS
1 +42V
2 GND
CN203
3 GND
4 -42V
PCB-P150D11+REG
CN602
1 GND
2 +8V

CN1

CN401

CN5

CN6

CN7

CN205

CN601

CN201

CN203

PCB-P150D11+RCA
1
GND
2
MIC1+
3
MIC14
MIC2+
5
MIC26
MIC3+
7
MIC38
GND
9
RCA IN1
10
RCA IN2
11
STEREO R
12
STEREO L
13
TAPE OUT R
14
TAPE OUT L
15
GND
PCB-P150D21+DSPR
1 GND
2 +15V
3 REV OUT
4 REV IN
5 FS
PCB-P150D11+PWRM
1 AUDIO IN L
2 GND
3 AUDIO IN R
PCB-P150D11+PWRM
1 -15V
2 +15V
PCB-P150D11+SMPS
1 GND
2 GND
WIRELESS PCB
3 AF_CH1
4 GND
WIRELESS PCB
8 AF_CH2
7 GND
PCB-P150D11+LED
1 GND
2 +15V
PCB-P150D11+REG
1 +42V
2 GND
PCB-P150D11+PWRM
1 GND
2 GND
PCB-P150D21+PWRM
1 +42V
2 GND
3 GND
4 -42V
WIRELESS PCB
5 GND
6 +8V

PASSPORT
Wiring Diagram
19

PASSPORT

Block Diagram

20

L/R Tape
Output

L/R ST
Input

L/R Sum

Line3

Line2

Line1

Foot Switch

Stereo Aux Return

Mono Aux Send

Stereo In

CH3

CH2

CH1

RCA/XLR
Input Board

ST/Mono
Switch

Level

EQ HI

Contour Level

Contour Level

Level EQ LOW

Gain Switch

Gain Switch

Contour

Gain Switch

Balance

PAN

PAN

PAN

Effects
Control

Rev/Aux

Rev/Aux

Rev/Aux

Rev/Aux

VIP Ducking

Mixer Board

Master
Reverb

IN

Reverb Board

OUT

+15V

GND

Left

Master

Master
Right

Speaker
EQ

Auto
Response

GND

+15V

-15V

SMPSU

Mains
Input

GND -42V GND +42V

-15V +15V GND

+36V

GND

-36V

Fan
Power

Short
Protect

Stereo
Power Amp

LED
PCB

Power
Switch

L Speaker
Out

R Speaker
Out

Power

Aux

DC--DC

NO.
1
2
3
4
5
6
7

DESCRIPTION
SPEAKER ASSEMBLY
TOWER HOUSING ASSEMBLY
GIG BAG
MICROPHONE
MIC CABLE
MIC CLIP
DSUT FILTER

PART NO.
SS-EF010C-SPK

QTY
2
1
1
1
1
1
1

1497-2132+0
1525-1120+0
7010-8290+0
4133-9100+0
9500-0900+0

Main Unit Ass’y Exploded View

Main Unit Ass’y Exploded View
21

NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18/19
20
21

DESCRIPTION
FRONT SHEET
FRONT PANEL
SHIELD PLATE
MIXER PCB ASSEMBLY
REVERB PCB ASSEMBLY
RCA/XLR PCB ASSEMBLY
XLR MIC JACK (RCA/XLR ASSY)
MIC JACK BRACKET (RCA/XLR)
SWITCH COVER
3x8MM SCREW TF
M3 FIBER WASHER
PCB STANDOFF
MIXER CONTROL KNOB
MASTER CONTROL KONB
LED PCB ASSEMBLY
3x8MM SCREW PHPS
“U” BAR
M3 METAL WASHER
M12 HEX T-NUT
M13 METAL WAHSRE

PART NO.
8900-1651+0
4153-2770+1
4133-9550+0
1723-073A+0000
1723-075A+0000
1723-080A+0000
2113-1223+0
4133-9570+0
3100-9080+0
2954-3008+3000
2601-3008+0801
4153-1220+0
4153-2830+0
4153-2820+0
1723-074A+0
2944-3008+3000
4153-2980+0
2600-3003+0402
4133-9660+0
4133-9650+0

QTY
1
1
1
1
1
1
3
1
4
15
2
4
20
2
1
6
2
8
7
7

10
10
11
4
D

10

3

8

10

9
6

11

5

10
9

7

12

10

12

2

10
B

A
10
15

13

10
C
10

17

17
14

18
16
1
20

21

10

19

Mixer Ass’y Exploded View

Mixer Exploded View
22

3

NO.
1
2
3
4
5

2
4
5

DESCRIPTION
LATCH ARM
LATCH BRACKET
LATCH “C” PINS
LATCH SPRING
LATCH SAFETY CATCH

PART NO.
4153-2730+0
4133-9540+0
4133-9430+0
4133-9550+0
4153-2740+1

QTY
1
1
2
1
1

Remark:
Each unit contains 4 latch assemblies.

1

3

Latch Ass’y Exploded View
12
16
16 6
11

12
17

8
9
18

16
16

1

7

10

12

16

15

18
18

10

12
4
5

8

A

2
14
3

NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18

DESCRIPTION
REAR PANEL
AUX POWER CON BRACKET
GM FUSE HOLDER HOUSING
AUX POWER CONNECTOR
2.6x6MM SCREW TF
FUSE COVER
POWER AMP HEAT SINK
MOUNTING BRACKET
POWER AMP PCB ASSEMBLY
BRASS TUBE STANDOFF
THERMAL MOUNTING BRACKET
3x12MM SCREW PHPS
SMPSU MODULE
DC FAN (SMPSU MODULE)
M3 METAL WASHER
3x6MM SCREW PHPS
M3 METAL SPRING WASHER
3x8MM SCREW PHPS

PART NO.
4133-946G+0
4133-9510+0
4153-1160+0
7010-0140+0
2934-2606+3000
1454-2590+0
5400-1881+1
4133-9490+0
PCB-P150D11+PWRM
4133-9580+0
4133-9090+0
2944-3012+3000
SS-P150D11+SMOS
8900-9520+0
2606-3005+0803
2904-3014+3000
2607-3009+0553
2954-3008+3000

QTY
1
1
1
1
2
1
1
2
1
2
1
9
1
1
4
11
12
4
23

13

Power Module Ass’y Exploded View

Latch Exploded View

3
4
9
8

11
6
2
7

10

12
13
14

1

15

5
12
16

Speaker Ass’y Exploded View

NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

DESCRIPTION
PD150 8 OHM WOOFER
PD150 4 OHM TWEETER
SPEAKER BOX PD150
BAFFLE PD150
STAND PLOG
SPEAKER GRILLE
BAFFLE GASKET
SPRUE CAP (BLK) PD150
RED SPRUE CAP
M4x14mm SCREW PHPS
M4x14mm SCREW TF
3x10MM SCREW FLAT HEAD
M12 WAHSRE
12MM HEX NUT
SPEAKER STAND “O” RING
6x25MM SCREW TF

PART NUMBER
8900-5870+0
8900-3500+0
1464-4302+1
4154-3801+0
4154-3841+0
4133-9440+0
4153-2880+0
4153-2812+0
4153-2900+0
2954-4014+3000
2954-4010+3000
2951-3010+3000
4133-2810+0
4133-2820+0
4152-2091+0
2904-6025+3000

QTY
1
2
1
1
1
1
1
1
1
1
8
2
1
1
1
4

Speaker Ass’y Exploded View
24

Tower Housing Ass’y Exploded View
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20

DESCRIPTION
CONSOLE PD 150
FRONT PANEL EXPLODER
POWER EXPLODER
SIDE PALTE-B
HANDLE COVER
PARTITION
DOOR
LOCKER DOOE
F3X8MM SELF TAPPING
HINGE
COMPRESSION SPRING
FOOT STAND PD150
SUPPORT RIB
HANDLE BKT
GASKET – TOP PD150
GASKET - HANDLE PD150
GASKET – BOTTOM PD150
LATCH LOCKER EXPLODER
TTS SCREW M2.6X8 BH
SCREW TAP-C2 BH M4X10 BZ CROSS

PART NO.
4153-2701+0

4133-9480+0
4153-2690+0
4133-9450+0
4153-2750+0
4153-2760+0
2954-3008+3000
4153-2780+0
4133-9560+0
4153-2712+0
4153-2720+0
4132-4901+0
4153-2862+1
4153-2852+1
4153-2872+1
2944-2608+0000
2954-4010+3000

QTY
2
1
1
1
1
1
1
1
4
2
1
2
1
2
1
1
1
4
8
8

NO.
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35

DESCRIPTION
SCREW B-TITE BH M4X14MM BZ CROSS
SCREW FLAT-CS M3X5MM BZ CROSS
SCREW TAP-BT BH M2.6X6MM BZ CROSS
S-TITE 3X8 (BLK)
SCREW TAP-BT BH M3X6MM BZ CROSS
SIDE PLATE-A
METAL WASHER M3X0.5X8MM BZ
FENDER BADGE PD150
SPRUE CAP (BLK)
4X16MM PA
SCREW S-TITE 4X16MM PH BLK ZINC
SPRING WASHER M4X0.8X6.5MM BZ
METAL WASHER M4X0.8X10MM BZ
SPRING WASHER M3X0.9X5.5MM BZ
HALO BUSHING 0813C

PART NO.
2954-4014+3000
2901-3005+3000
2934-2606+3000
2944-3008+3000
2944-3006+3000
4133-9470+0
2600-3005+0803
4154-3831+0
4153-2812+0
2910-4016+3000
2940-4016+3000
2607-4008+0653
2600-4008+1003
2670-3009+0553
2113-9535+0

QTY
6
2
2
9
12
1
10
2
2
2
8
8
8
3
1

Tower Housing Exploded View
25

Packing Ass’y Exploded View
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18

DESCRIPTION
GIFT BOX PD150
2751-P12-0 PLOY BAG
2751-P1-0 INNER PAD
2751-P2-0 INNER PAD
2751-P3-0 INNER PAD
2751-P4-0 P.E. FOAM
POLYGAB P.E. 04X10X10
PD150 UNIT
2751-P7-0 CARTON BOARD
2751-P6-0 P.E. FOAM
2751-P5-0 P.E. FOAM
SPK CABLE MONO 90 ANGLE PLUG
L=30FT
SJT #18/3C 2M BLK POWER CORD
OWNER’S MANUAL PD150
INNER PAD 480X230X3 A-A
PE FOAM-SIDE
RCA CABLE
OUTER CARTON

PART NO.
1434-2104+0-3
1497-2540+0
1434-2300+0-2
1434-2400+0-1
1434-2500+0-1
9500-8700+0
1497-2092+0
1434-2200+0-1
9500-0890+0
9500-0880+0
7010-0000+0

QTY
1
1
2
2
2
2
2
1
2
1
1
2

7011-6210+0
4301-7217+0
1450-9450+0
1493-1701+0
7011-3271+0
1437-9901+0-1

1
1
2
2
1
1
26

Packing Exploded View



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-702
Create Date                     : 2012:06:21 16:08:21Z
Creator Tool                    : Microsoft® Office Word 2007
Modify Date                     : 2012:06:21 16:11:09-07:00
Metadata Date                   : 2012:06:21 16:11:09-07:00
Format                          : application/pdf
Description                     : Service Manual Template
Creator                         : Scott Bringe
Title                           : Service Manual Template
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:5806a73c-1275-4ff6-b861-1044ae6e7eaa
Instance ID                     : uuid:1c463e43-f817-4519-84f9-28450c209325
Has XFA                         : No
Page Count                      : 48
Language                        : en-US
Subject                         : Service Manual Template
Author                          : Scott Bringe
Keywords                        : Service, Manual
EXIF Metadata provided by EXIF.tools

Navigation menu