Fleetwood Group V240B Low Power RF and IR Module User Manual CERTIFICATE OF COMPLIANCE

Fleetwood Group Inc Low Power RF and IR Module CERTIFICATE OF COMPLIANCE

User Manual

Rhein Tech Laboratories, Inc. Client: Fleetwood Group, Inc. 360 Herndon Parkway Model: V240B Suite 1400 Standards: FCC 15.249/IC RSS-210 Herndon, VA 20170 http://www.rheintech.com FCC/IC ID: FBRV240B/1859A-V240B Report #: 2010232 Page 29 of 39 Appendix L: Manual Please refer to the following pages.
USER MANUAL VL4B Module
ii Copyright 2007 Fleetwood Group, Inc., Electronics Division. All rights reserved. Licensed software products are owned by Fleetwood Group, Inc. or its suppliers and are protected by United States copyright laws and international treaty provisions. Fleetwood Group, Inc. products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specifications and pricing are subject to change without notice. Printed in the U.S.A. Fleetwood Group, Inc. Electronics Division 11832 James St. Holland, Michigan 49424 www.fleetwoodgroup.com Sales: 1-800-257-6390 Technical Service: 1-888-GO-REPLY (467-3759) Reply® is a registered trademark of Fleetwood Group, Inc. Other trademarks contained herein are the property of their respective holders. Revision History: Rev Date Description A 12/8/2010 Original
iii Table of Contents 1.0 V240B MODULE .................................................................................................................................................. 4 1.1 DESCRIPTION ....................................................................................................................................................... 4 1.2 BATTERY REPLACEMENT ..................................................................................................................................... 4 1.3 FCC AND IC ......................................................................................................................................................... 4 1.4 STANDARDS AND GUIDELINES ............................................................................................................................. 4 1.5 FCC/IC COMPLIANCE .......................................................................................................................................... 5
4 1.0 VL4B Module 1.1 Description The V240B is a low power real time locating system badge. The V240B module is used to identify the location of an individual or asset location. It communicates at 2.4GHz, to a ceiling sensor module or a link module, and uses IR emitters that communicate with the ceiling sensor to determine its location. The overall operation of the V240B module is controlled by a microcontroller. This microcontroller is powered from approximately 3V and uses a 16 MHz reference. The microcontroller handles control of the RF and IR communications, indicator LEDs, external I/O, and keypad inputs. RF communications use a 2.4 GHz transceiver. The transceiver chip uses a 16 MHz reference oscillator that is shared with the microcontroller for TX/RX and is also powered by 3V. The transceiver uses an integral antenna on the PCB. 1.2 Battery Replacement The V240B is powered from a 3V battery. The battery is replaceable. To replace battery, open the case, remove the old battery, and replace with a new battery noting its polarity. The negative side of the battery should be facing the PCB. 1.3 FCC and IC V240B Module Responsible Party Pertaining to the Declaration of Conformity Fleetwood Group, Inc. 11832 James Street Holland, MI 49424 Attn: Product Service Coordinator Phone: 888-467-3759 1.4 Standards and Guidelines This device complies with the following USA/Canada Regulations:  The USA Federal Communications Commission (FCC) Rules and Regulations  Industry Canada Rules and Regulations This device complies with the following national and international standards:  FCC Part 15B, 15.249 (10-01-09)  IC RSS-210 Issue 7
5 1.5 FCC/IC Compliance This device complies with Part 15 of the FCC Rules and RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) this device may not cause interference and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The user is cautioned that changes or modifications to the device that are not approved by the manufacturer could void the user’s authority to operate the device.

Navigation menu