Fleetwood Group V240B Low Power RF and IR Module User Manual CERTIFICATE OF COMPLIANCE
Fleetwood Group Inc Low Power RF and IR Module CERTIFICATE OF COMPLIANCE
User Manual
Rhein Tech Laboratories, Inc.
Client:
Fleetwood Group, Inc.
360 Herndon Parkway
Model:
V240B
Suite 1400
Standards:
FCC 15.249/IC RSS-210
Herndon, VA 20170
http://www.rheintech.com
FCC/IC ID:
FBRV240B/1859A-V240B
Report #: 2010232
Page 29 of 39
Appendix L: Manual
Please refer to the following pages.
USER MANUAL
VL4B Module
ii
Copyright 2007 Fleetwood Group, Inc., Electronics Division. All rights reserved. Licensed software products are
owned by Fleetwood Group, Inc. or its suppliers and are protected by United States copyright laws and international
treaty provisions.
Fleetwood Group, Inc. products are covered by U.S. and foreign patents, issued and pending. Information in this
publication supersedes that in all previously published material. Specifications and pricing are subject to change
without notice.
Printed in the U.S.A.
Fleetwood Group, Inc.
Electronics Division
11832 James St.
Holland, Michigan 49424
www.fleetwoodgroup.com
Sales: 1-800-257-6390
Technical Service: 1-888-GO-REPLY (467-3759)
Reply® is a registered trademark of Fleetwood Group, Inc.
Other trademarks contained herein are the property of their respective holders.
Revision History:
Rev
Date
Description
A
12/8/2010
Original
iii
Table of Contents
1.0 V240B MODULE .................................................................................................................................................. 4
1.1 DESCRIPTION ....................................................................................................................................................... 4
1.2 BATTERY REPLACEMENT ..................................................................................................................................... 4
1.3 FCC AND IC ......................................................................................................................................................... 4
1.4 STANDARDS AND GUIDELINES ............................................................................................................................. 4
1.5 FCC/IC COMPLIANCE .......................................................................................................................................... 5
4
1.0 VL4B Module
1.1 Description
The V240B is a low power real time locating system badge. The V240B module is used to identify the location of
an individual or asset location. It communicates at 2.4GHz, to a ceiling sensor module or a link module, and uses IR
emitters that communicate with the ceiling sensor to determine its location.
The overall operation of the V240B module is controlled by a microcontroller. This microcontroller is powered
from approximately 3V and uses a 16 MHz reference. The microcontroller handles control of the RF and IR
communications, indicator LEDs, external I/O, and keypad inputs.
RF communications use a 2.4 GHz transceiver. The transceiver chip uses a 16 MHz reference oscillator that is
shared with the microcontroller for TX/RX and is also powered by 3V. The transceiver uses an integral antenna on
the PCB.
1.2 Battery Replacement
The V240B is powered from a 3V battery. The battery is replaceable. To replace battery, open the case, remove the
old battery, and replace with a new battery noting its polarity. The negative side of the battery should be facing the
PCB.
1.3 FCC and IC
V240B Module
Responsible Party Pertaining to the Declaration of Conformity
Fleetwood Group, Inc.
11832 James Street
Holland, MI 49424
Attn: Product Service Coordinator
Phone: 888-467-3759
1.4 Standards and Guidelines
This device complies with the following USA/Canada Regulations:
The USA Federal Communications Commission (FCC) Rules and Regulations
Industry Canada Rules and Regulations
This device complies with the following national and international standards:
FCC Part 15B, 15.249 (10-01-09)
IC RSS-210 Issue 7
5
1.5 FCC/IC Compliance
This device complies with Part 15 of the FCC Rules and RSS-210 of the Industry Canada Rules. Operation is subject to
the following two conditions: (1) this device may not cause interference and (2) this device must accept any interference,
including interference that may cause undesired operation of the device. The user is cautioned that changes or
modifications to the device that are not approved by the manufacturer could void the user’s authority to operate the device.