Flir BelgiumBA RAY90 Ray 91 VHF Black Box with AIS Rx User Manual

Raymarine UK Ltd. Ray 91 VHF Black Box with AIS Rx

User Manual

Download: Flir BelgiumBA RAY90 Ray 91 VHF Black Box with AIS Rx User Manual
Mirror Download [FCC.gov]Flir BelgiumBA RAY90 Ray 91 VHF Black Box with AIS Rx User Manual
Document ID3755052
Application IDN4XLa6uAa939kJkT7YTuCg==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize403.33kB (5041624 bits)
Date Submitted2018-02-15 00:00:00
Date Available2018-04-01 00:00:00
Creation Date2017-12-21 18:13:25
Producing SoftwarePDFlib+PDI 9.0.3p4 (Win32)
Document Lastmod2018-02-15 10:38:31
Document TitleUser Manual
Document CreatorPTC Arbortext Editor with Styler

81377-1-en_US_PRINT.pdf 1
12/21/2017 9:05:36 PM
Trademark and patents notice
Raymarine, Tacktick, Clear Pulse, Truzoom, HSB, SeaTalk , SeaTalk hs, SeaTalk ng, Micronet, Raytech, Gear Up, Marine Shield, Seahawk, Autohelm, Automagic, and Visionality
are registered or claimed trademarks of Raymarine Belgium.
FLIR, LightHouse, DownVision, SideVision, RealVision, Dragonfly, Quantum, Instalert, Infrared Everywhere, The World’s Sixth Sense and ClearCruise are registered or
claimed trademarks of FLIR Systems, Inc.
All other trademarks, trade names, or company names referenced herein are used for identification only and are the property of their respective owners.
This product is protected by patents, design patents, patents pending, or design patents pending.
Fair Use Statement
You may print no more than three copies of this manual for your own use. You may not make any further copies or distribute or use the manual in any other way including without
limitation exploiting the manual commercially or giving or selling copies to third parties.
81377-1-en_US_PRINT.pdf 2
12/21/2017 9:05:36 PM
Software updates
Check the Raymarine website for the latest software releases for your product.
www.raymarine.com/software
Product documentation
The latest versions of all English and translated documents are available to download in PDF format from the website:
www.raymarine.com/manuals.
Please check the website to ensure you have the latest documentation.
Copyright ©2017 Raymarine UK Ltd. All rights reserved.
English (en-US)
Document number: 81377-1
AA;6819;2017-12-21T18:06:26
81377-1-en_US_PRINT.pdf 3
12/21/2017 9:05:36 PM
Product documentation
The latest versions of all English and translated documents are available to download in PDF format from the website:
www.raymarine.com/manuals.
Please check the website to ensure you have the latest documentation.
Copyright ©2017 Raymarine UK Ltd. All rights reserved.
81377-1-en_US_PRINT.pdf 4
12/21/2017 9:05:36 PM
Contents
Chapter 1 Important information ....................................... 9
Certified Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
FCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Compliance Statement (Part 15.19) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
FCC Interference Statement (Part 15.105 (b)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.7 Parts supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.8 Software updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Checking software versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Preparing the Raymic handset for the software update
process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Industry Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 3 Installation .................................................... 19
Industry Canada (Français) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1 Selecting a location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Water ingress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
General location requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Antenna mounting and EME exposure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.2 EMC installation guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Product disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Suppression ferrites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Warranty registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connections to other equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Technical accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.3 Product dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Chapter 2 Document and product information ................... 13
Product dimensions - Base station. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Product dimensions - speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.1 Product documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Product dimensions - Raymic handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
User manuals Print Shop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.4 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Document illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Tools required for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.2 Applicable products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Mounting the Base station. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Required additional components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Pass-through panel kit mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.3 Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Raymic handset cradle mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.4 Licensing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Passive speaker mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
USA licensing requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Chapter 4 Cables and connections.................................. 25
Canada licensing requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Europe and rest of world licensing requirements . . . . . . . . . . . . . . . . . . . . . . . . 15
4.1 General cabling guidance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cable types and length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
2.5 Obtain MMSI (Maritime Mobile Service Identity)
number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Routing cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Strain relief. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
2.6 Automatic Transmitter Identification System (ATIS) . . . . . . . . . . . . . . 16
81377-1-en_US_PRINT.pdf 5
12/21/2017 9:05:36 PM
Circuit isolation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Enabling Shared Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Cable shielding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.6 Initial startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Dust caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.7 Selecting a language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Connections to other equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.8 Switching on the AIS receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.2 Connections overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.9 Selecting a network type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Bare end wire connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.10 Entering your MMSI number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.3 Power connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.11 Entering your ATIS ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
In-line fuse and thermal breaker ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Enabling and disabling ATIS mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.12 Changing the radio region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Power distribution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.4 Handset station connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Connecting handsets and cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Handset extension cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.5 Passive speaker connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
5.13 Switching between high and low transmit power . . . . . . . . . . . . . . . 41
5.14 GNSS (GPS) set up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Enabling and disabling the internal GNSS (GPS) . . . . . . . . . . . . . . . . . . . . . . . . 42
No GPS position data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Entering position manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.6 NMEA 2000 / SeaTalkng ® connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Selecting GPS information to display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Connecting SeaTalkng ® cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Setting time format and offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.7 NMEA 0183 connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.8 Loud hailer connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.9 Connecting GNSS (GPS) and VHF antennas . . . . . . . . . . . . . . . . . . . . . 32
Chapter 6 Digital selective calling (DSC) .......................... 43
6.1 Digital Selective Calling (DSC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
6.2 Distress calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Chapter 5 Getting started.............................................. 33
Making a designated distress call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
5.1 Raymic handset controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Making a distress call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
5.2 Powering the Base station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Making a Mayday call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Powering the handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Cancelling a distress call before transmission . . . . . . . . . . . . . . . . . . . . . . . . . . 45
5.3 Homescreen overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Cancelling a distress call after transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Status bar symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Main menu overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
5.4 Shortcut list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Receiving a distress call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Ignoring a distress call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Acknowledging a distress call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Manually relaying a distress call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Adjusting Brightness and Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Distress relays sent by other stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
5.5 Shared Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6.3 Urgency calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
81377-1-en_US_PRINT.pdf 6
12/21/2017 9:05:36 PM
Making an urgency call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Performing a scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Receiving an urgency call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
7.3 Priority channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
6.4 Safety calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Switching between priority channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Making a safety call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Setting a second priority channel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Receiving a safety call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
7.4 Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.5 Individual (routine) calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Switching sensitivity modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Making a routine DSC call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
7.5 Private channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Receiving an individual (routine) call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Selecting a private channel set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.6 Group calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
7.6 Automatic Transmitter Identification System (ATIS) and
Marcom-C mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Making a group call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Receiving a group call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Enabling and disabling ATIS mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
6.7 Position requests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
7.7 AIS receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Making a position request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Switching AIS on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Responding to a position request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
7.8 Set-up menu options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Setting automatic response to position requests . . . . . . . . . . . . . . . . . . . . . . . 50
6.8 Phonebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Display Set-up menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Shared Brightness menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Adding a phonebook entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Editing a phonebook entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Chapter 8 Hailer, Fog horn, and Intercom .......................... 61
Deleting a phonebook entry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
8.1 Hailer Fog Intercom menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6.9 Call logs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
8.2 Loud Hailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Accessing the call logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Using the hailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6.10 Test calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
8.3 Fog horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Making a test call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Using the fog horn in manual mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Receiving a test call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Using automatic fog horn modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
6.11 DSC set-up menu options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Switching off Fog Horn mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
8.4 Intercom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Chapter 7 VHF operations ............................................. 53
7.1 Watch modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Using the intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Responding to the intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Using watch modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
7.2 Scan Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Chapter 9 Maintenance................................................. 65
81377-1-en_US_PRINT.pdf 7
12/21/2017 9:05:36 PM
9.1 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Appendix E Phonetic alphabet........................................ 99
Routine checks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Unit cleaning instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Appendix F Prowords .................................................. 100
Chapter 10 Troubleshooting........................................... 67
10.1 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Performing a system reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
System test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
10.2 Power up troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
10.3 VHF Radio troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
10.4 GNSS (GPS) troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
GPS data output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Chapter 11 Technical support ......................................... 73
11.1 Raymarine product support and servicing . . . . . . . . . . . . . . . . . . . . . . . . 74
11.2 Viewing product information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
11.3 Learning resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Chapter 12 Technical specification ................................... 77
12.1 Technical specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
12.2 Radio usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Appendix A NMEA 0183 sentences .................................. 81
Appendix B NMEA 2000 PGN list.................................... 82
Appendix C MMSI Regulatory bodies and application
submissions................................................................ 84
Appendix D VHF Channels ............................................ 86
81377-1-en_US_PRINT.pdf 8
12/21/2017 9:05:36 PM
Chapter 1: Important
information
Warning: 12 Volt dc only
This product must only be connected to a
12 volt dc power source.
Certified Installation
Warning: Chassis grounding
Raymarine recommends certified installation by a
Raymarine approved installer. A certified installation
qualifies for enhanced product warranty benefits.
Contact your Raymarine dealer for further details, and
refer to the separate warranty document packed with
your product.
Do NOT ground this product using the
chassis ground terminal.
Grounding this product to a vessel’s RF
ground may cause galvanic corrosion.
Warning: Positive ground
systems
Warning: Product installation
and operation
Do not connect this unit to a system which
has positive grounding.
• This product must be installed and
operated in accordance with the
instructions provided. Failure to do so
could result in personal injury, damage
to your vessel and/or poor product
performance.
Warning: Switch off power
supply
Ensure the vessel’s power supply is
switched OFF before starting to install this
product. Do NOT connect or disconnect
equipment with the power switched on,
unless instructed in this document.
• Raymarine recommends certified
installation by a Raymarine approved
installer. A certified installation qualifies
for enhanced product warranty benefits.
Contact your Raymarine dealer for further
details, and refer to the separate warranty
document packed with your product.
Warning: Potential ignition
source
This product is NOT approved for use in
hazardous/flammable atmospheres. Do
NOT install in a hazardous/flammable
atmosphere (such as in an engine room or
near fuel tanks).
Important information
81377-1-en_US_PRINT.pdf 9
Compliance Statement (Part 15.19)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1.
FCC Interference Statement (Part
15.105 (b))
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one of the following measures:
1.
Changes or modifications to this equipment
not expressly approved in writing by
Raymarine Incorporated could violate
compliance with FCC rules and void the
user’s authority to operate the equipment.
Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment
and receiver.
3.
Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
4.
Consult the dealer or an experienced radio / TV
technician for help.
FCC
Warning: FCC Warning (Part
15.21)
This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
Innovation, Science and
Economic Development Canada
This device complies with ISEDC License-exempt.
RSS standard(s).
Operation is subject to the following two conditions:
12/21/2017 9:05:36 PM
1.
This device may not cause interference; and
2. This device must accept any interference, including
interference that may cause undesired operation
of the device.
This Class B digital apparatus complies with Canadian
ICES-003.
Innovation, Sciences et Développement
économique Canada (Français)
Cet appareil est conforme aux normes d'exemption de
licence RSS d'ISEDC.
Son fonctionnement est soumis aux deux conditions
suivantes:
1.
cet appareil ne doit pas causer d'interférence, et
2. cet appareil doit accepter toute interférence,
notamment les interférences qui peuvent affecter
son fonctionnement.
Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
Warning: VHF Antenna
isolation
To prevent galvanic corrosion your VHF
antenna must be isolated from any vessel
metalwork using a suitable insulated e.g.
plastic, mounting bracket.
This radio complies with the ITU-R M493-13 requirements.
Warning: Maximum
Permissible Exposure
Water ingress
Water ingress disclaimer
Failure to observe these guidelines
may expose those within the Maximum
Permissible Exposure (MPE) radius to RF
radiation absorption that exceeds the
FCC MPE limit. It is the radio operator’s
responsibility to ensure that no person
comes within this radius.
Although the waterproof rating capacity of this product
meets the stated IPX standard (refer to the product’s
Technical Specification), water intrusion and subsequent
equipment failure may occur if the product is subjected
to commercial high-pressure washing. Raymarine
will not warrant products subjected to high-pressure
washing.
For optimal radio performance and minimal
human exposure to Radio Frequency (RF)
electromagnetic energy, you must ensure
that the antenna is:
Disclaimer
• connected to the radio before
transmitting;
• located where it will be away from people;
• located at least 1.3meters (4.2ft.) from
the radio’s main unit.
Caution: Perform regular
radio checks
Perform regular radio checks when using
your vessel, as recommended in radio
training and certification schemes and radio
equipment rules of use.
Caution: Ensure proper radio
use
Raymarine does not warrant that this product is error-free
or that it is compatible with products manufactured by
any person or entity other than Raymarine.
Raymarine is not responsible for damages or injuries
caused by your use or inability to use the product, by the
interaction of the product with products manufactured
by others, or by errors in information utilized by the
product supplied by third parties.
Declaration of Conformity
FLIR Belgium BVBA declares that the radio equipment
types Ray90 and Ray91 DSC VHF Radios, part numbers
E70492 and E70493, are in compliance with the Radio
Equipment Directive 2014/53/EU.
The original Declaration of Conformity certificate
may be viewed on the relevant product page at
www.raymarine.com/manuals.
Under no circumstances should a DSC
distress alert be sent from your radio for
test purposes. Such action is a violation of
rules of use for radio equipment, and can
result in heavy fines.
10
81377-1-en_US_PRINT.pdf 10
12/21/2017 9:05:36 PM
Product disposal
Dispose of this product in accordance with the WEEE
Directive.
The Waste Electrical and Electronic Equipment
(WEEE) Directive requires the recycling of waste
electrical and electronic equipment.
Warranty registration
To register your Raymarine product ownership, please
visit www.raymarine.com and register online.
It is important that you register your product to receive
full warranty benefits. Your unit package includes a
bar code label indicating the serial number of the unit.
You will need this serial number when registering your
product online. You should retain the label for future
reference.
Important information
81377-1-en_US_PRINT.pdf 11
11
12/21/2017 9:05:36 PM
Technical accuracy
To the best of our knowledge, the information in this
document was correct at the time it was produced.
However, Raymarine cannot accept liability for any
inaccuracies or omissions it may contain. In addition, our
policy of continuous product improvement may change
specifications without notice. As a result, Raymarine
cannot accept liability for any differences between the
product and this document. Please check the Raymarine
website (www.raymarine.com) to ensure you have the
most up-to-date version(s) of the documentation for your
product.
12
81377-1-en_US_PRINT.pdf 12
12/21/2017 9:05:36 PM
Chapter 2: Document and product information
Chapter contents
•
2.1 Product documentation on page 14
•
2.2 Applicable products on page 14
•
2.3 Product overview on page 15
•
2.4 Licensing on page 15
•
2.5 Obtain MMSI (Maritime Mobile Service Identity) number on page 16
•
2.6 Automatic Transmitter Identification System (ATIS) on page 16
•
2.7 Parts supplied on page 16
•
2.8 Software updates on page 17
Document and product information
81377-1-en_US_PRINT.pdf 13
13
12/21/2017 9:05:36 PM
2.1 Product documentation
Note:
2.2 Applicable products
The following documentation is applicable to your
product:
• Accepted methods of payment for printed manuals
are credit cards and PayPal.
This document is applicable to the following products:
• Printed manuals can be shipped worldwide.
Description
Part number
Installation and
operation instructions
81377
Ray90 / Ray91 mounting
template
87329
All documents are available to download
in pdf format from the Raymarine® website:
www.raymarine.com/manuals.
• Further manuals will be added to the Print Shop
over the coming months for both new and legacy
products.
Part number
Features
Ray90
E70492
• Built-in GNSS
(GPS and
GLONASS)
receiver
• Raymarine user manuals are also available to
download free-of-charge from the Raymarine
website, in the popular PDF format. These PDF
files can be viewed on a PC / laptop, tablet,
smartphone, or on the latest generation of
Raymarine multifunction displays.
User manuals Print Shop
Document illustrations
Raymarine provides a Print Shop service, enabling you
to purchase a high-quality, professionally-printed manual
for your Raymarine product.
Your product and if applicable, its user interface may
differ slightly from that shown in the illustrations in this
document, depending on product variant and date of
manufacture.
Printed manuals are ideal for keeping onboard your
vessel, as a useful source of reference whenever you
need assistance with your Raymarine product.
Name
• Up to 2 wired
handset stations
• Loud hailer
connection
• SeaTalkng ® /
NMEA 2000
connection
• NMEA 0183
connection
Ray91
All images are provided for illustration purposes only.
Same as Ray90
above, with
additional:
• Built-in AIS
receiver
Visit http://www.raymarine.co.uk/view/?id=5175 to order
a printed manual, delivered directly to your door.
For further information about the Print Shop,
please visit the Print Shop FAQ pages:
http://www.raymarine.co.uk/view/?id=5751.
E70493
Required additional components
Your product requires a VHF and GNSS (GPS) antenna
to be connected.
Part number
Description
A80288
Passive GNSS (GPS) antenna
N/A
3rd Party VHF antenna
14
81377-1-en_US_PRINT.pdf 14
12/21/2017 9:05:36 PM
2.3 Product overview
2.4 Licensing
The Ray90 and Ray91 are 12 V dc, Class D Digital
Selective Calling (DSC) VHF radios. DSC enables you
to make and receive calls to a specific radio, and to
transmit and receive position information to and from
a selected radio. DSC also allows transmission of a
distress alert, to all radios within range, at the touch of a
button. Once a DSC request is sent and acknowledged
voice communication is carried out on the channel
chosen by the caller. The radio can transmit and receive
on all available US, Canadian, International and Private
marine VHF channels.
Prior to using this product please check your national
requirements for both operator and equipment licensing.
The Ray90 and Ray91 include a built-in GNSS (GPS)
receiver.
The Ray91 also includes a built-in AIS receiver.
Your radio includes a base station with 2 x wired
handset connections.
With an optional loud hailer connected the radio can
also be used as a fog horn or loud public address (PA)
system.
USA licensing requirements
FCC station license requirement
An FCC Ship Radio Station License and Call Sign are
not required for most recreational vessels travelling in
US waters. However, you must obtain a license if your
vessel travels to foreign ports.
Ships that use MF/HF single side-band radio, satellite
communications, or telegraphy must be licensed by the
FCC. You can obtain a Station License by filing FCC
Form 605.
Additional information
The following additional information is required for
completing a license application in Canada and the USA.
Industry Canada
certification
number
4069B-RAY90D
FCC ID
PJ5–RAY90
FCC Type
accepted
Parts 2, 15 and 80
Output power
1 watt (low) and 25 watt (high)
Modulation
FM
Frequency range
155.500 MHz to 163.275 MHz
Canada licensing requirements
Industry Canada license requirement
You do not need a license to operate this product within
the sovereign waters of Canada or the United States of
America (USA). You will need a license to operate this
radio outside of Canada or the USA. To obtain Industry
Canada licensing information, contact the nearest field
or regional office, or write to:
Industry Canada Radio Regulatory Branch
Attention: DOSP
300 Slater Street
Ottawa, Ontario
Canada, KIA OC8
Europe and rest of world licensing
requirements
Regulations in some areas require that an Operator’s
license is obtained before operating a VHF radio. It is
your responsibility to determine whether a license is
required in your area before operating this equipment.
Document and product information
81377-1-en_US_PRINT.pdf 15
15
12/21/2017 9:05:36 PM
2.5 Obtain MMSI (Maritime
Mobile Service Identity) number
2.6 Automatic Transmitter
Identification System (ATIS)
Before commencing installation ensure you have
obtained a MMSI number for your vessel.
Your product includes ATIS functionality for use on the
inland waterways of contracting governments of the
A MMSI is a 9 digit number which is sent over a radio
frequency channel in order to identify the originating
vessel/station. If your vessel already has a MMSI number
(used for a VHF DSC radio) then the same MMSI number
must be used to program your product.
Note:
If a MMSI number is not entered, the DSC functionality
of your radio will be disabled.
In the United States of America, the MMSI and Static
Data must be entered only by a Raymarine® dealer
or other appropriately qualified installer of marine
communications equipment on board vessels.
The user is NOT authorized to do this.
In some areas, a radio operator licence is required
before a MMSI number will be issued. You can request
a MMSI number from same agency that issues radio or
Ship Radio licences in your area.
In Europe and other parts of the world outside of the
United States of America, the MMSI and Static data can
be set up by the user.
For further details, refer to the relevant
Telecommunications Regulatory Body for your
area.
Refer to Appendix C MMSI Regulatory bodies and
application submissions
for a list of contacts for obtaining MMSI numbers for
some areas.
Warning: MMSI entry
You can only enter a MMSI number once, if
you enter the number incorrectly or need
to change your MMSI number, the unit will
require re-programming by an authorized
dealer.
2.7 Parts supplied
The following parts are supplied with your product.
Please ensure your box contents are correct before
proceeding with the installation.
“Regional Arrangement on the Radiocommunication
Service for Inland Waterways” — also known as
“RAINWAT” .
ATIS adds data at the end of radio transmissions that
identifies your station. ATIS operation can be turned on
or off as needed via the radio’s menu.
An ATIS ID can be obtained from the same agency that
issues radio operator licenses in your area.
Your ATIS ID should be programed into your product
using the instructions provided.
Note:
Contracting RAINWAT countries include: Austria,
Belgium, Bulgaria, Croatia, the Czech Republic,
France, Germany, Hungary, Luxembourg, Moldova,
Montenegro, the Netherlands, Poland, Romania,
Serbia, the Slovak Republic and Switzerland.
Note:
When ATIS is enabled, certain programing steps
have been implemented to protect the integrity of
the RAINWAT agreement, including the blocking of
DSC functions when ATIS is enabled.
1.
Ray90 / Ray91 VHF DSC Radio (including fitted
power and data cable)
2. Raymic handset cradle
3.
Raymic handset
4.
Raymic handset adaptor cable (12 pin female to 12
pin male with RCA Audio)
5. Passive speaker
6. Passive speaker mounting gasket
7.
Passive speaker mounting screws x 4
8. Documentation
9.
VHF radio mounting screws x 4
10. Handset cradle mounting screws x 4
11. DeviceNet to SeaTalkng ® adaptor
16
81377-1-en_US_PRINT.pdf 16
12/21/2017 9:05:36 PM
2.8 Software updates
Raymarine periodically releases software updates
for its products. These updates can provide new
and enhanced features and also improve product
performance and usability. You should ensure that you
have the latest software for your products by regularly
checking the website for new software. The software
update process requires a compatible MFD powered by
LightHouse™ 2 release 13 or greater, or LightHouse™ 3.
1. Select Menu > Set-up > Maintenance > About this
unit.
2. Scroll down.
The Base station’s and Handset's software versions
are displayed.
Check the Raymarine website regularly
for software updates for your products:
www.raymarine.com/software.
The MFD used to perform the software update must
be the designated Data master and be connected via
SeaTalkng ® / NMEA 2000 to the product being updated.
Please refer to the operation instructions for your MFD /
operating system version for details on how to perform
the software update.
If in doubt as to the correct procedure for updating your
product software, refer to your dealer or Raymarine
technical support.
Caution: Installing software
updates
The software update process is carried
out at your own risk. Before initiating the
update process ensure you have backed
up any important files.
Ensure that the unit has a reliable power
supply and that the update process is not
interrupted.
Damage caused by incomplete updates are
not covered by Raymarine warranty.
By downloading the software update
package, you agree to these terms.
Checking software versions
You can check the software version of your radio and
any connected Raymic handset.
From the Homescreen:
Document and product information
81377-1-en_US_PRINT.pdf 17
Preparing the Raymic handset for the
software update process
The Raymic must be placed in programming mode to
enable its software to be updated.
1. Power off your MFD.
2. Power on the Radio.
3. Ensure the Raymic handset is powered off.
4. Press and hold the Distress and PTT buttons on the
Handset.
5. Press the Handset’s Power button for 1 second, until
the backlight turns on, and then release all three
buttons.
The handset is now in programming mode, in
programming mode the handset’s screen remains
blank and the backlight will briefly flash off,
approximately once every 5 seconds. The handset
will now be updated at the same time as the Base
station.
6. Power your MFD on and follow the software
update process described in your MFD’s operation
instructions.
17
12/21/2017 9:05:36 PM
7. Once the software update is complete, Power cycle
your Radio and check the software version for both
the Base station and Handset is correct.
18
81377-1-en_US_PRINT.pdf 18
12/21/2017 9:05:36 PM
Chapter 3: Installation
Chapter contents
•
3.1 Selecting a location on page 20
•
3.2 EMC installation guidelines on page 21
•
3.3 Product dimensions on page 21
•
3.4 Mounting on page 22
Installation
81377-1-en_US_PRINT.pdf 19
19
12/21/2017 9:05:36 PM
3.1 Selecting a location
Warning: Potential ignition
source
This product is NOT approved for use in
hazardous/flammable atmospheres. Do
NOT install in a hazardous/flammable
atmosphere (such as in an engine room or
near fuel tanks).
General location requirements
When selecting a location for the unit it is important to
consider a number of factors.
Ventilation requirements
To provide adequate airflow:
• Ensure that equipment is mounted in a compartment
of suitable size.
• Ensure that ventilation holes are not obstructed.
• Ensure adequate separation of equipment.
Mounting surface requirements
Ensure units are adequately supported on a secure
surface. Do NOT mount units or cut holes in places
which may damage the structure of the vessel.
Water ingress
Ray90/91 Base station
Although the Base station is waterproof to IPx6 and IPx7,
it is recommended that the Base station is mounted
below decks, in an area protected from prolonged and
direct exposure to rain and salt spray.
Raymic Handset
The Handset has been designed to be mounted above
or below decks and is rated to IPx6 and IPx7.
Passive speaker
The speakers has been designed to be mounted above
or below decks and are rated to IPx6 and IPx7.
Cable routing requirements
Ensure the unit is mounted in a location which allows
proper routing and connection of cables:
• Minimum cable bend radius of 100 mm (3.94 in) is
required unless otherwise stated.
• Use cable supports to prevent stress on connectors.
Electrical interference
Select a location that is far enough away from devices
that may cause interference, such as motors, generators
and radio transmitters/receivers.
Power supply
Select a location that is as close as possible to the
vessel’s DC power supply. This will help to keep cable
runs to a minimum.
RF interference
Certain third-party external electrical equipment can
cause Radio Frequency (RF) interference with GNSS
(GPS), AIS or VHF devices, if the external equipment is
not adequately insulated and emits excessive levels of
electromagnetic interference (EMI).
Some common examples of such external equipment
include LED spot or strip lights, and terrestrial TV tuners.
To minimize interference from such equipment:
Antenna mounting and EME exposure
Ensure that your VHF antenna is connected to the radio
before transmission.
Raymarine® declares a Maximum Permissible Exposure
(MPE) radius of 1.3meters (4.2ft.) for this system,
assuming 25 watts output to an omnidirectional antenna
of 3dBi gain or less.
For watercraft with suitable structures, the antenna base
must be at least 3.8 meters (12.5 ft) above the main deck
to meet the MPE for persons up to 2 metres (6.6 ft) tall.
For watercraft without such structures, the antenna must
be mounted so that its base is a minimum of 1.3meters
(4.2ft.) vertically from heads of all persons.
The antenna must be isolated from the vessel’s
metalwork using an insulated (e.g. plastic) mounting
bracket.
• Keep it as far away from GNSS (GPS), AIS or VHF
devices as possible.
• Ensure that any power cables for external equipment
are not entangled with the power or data cables for
these devices.
• Consider fitting one or more high frequency
suppression ferrites to the EMI-emitting device. The
ferrite(s) should be rated to be effective in the range
100 MHz to 2.5 GHz, and should be fitted to the power
cable and any other cables exiting the EMI-emitting
device, as close as possible to the position where the
cable exits the device.
Compass safe distance
When choosing a suitable location for your product you
should aim to maintain the maximum possible distance
between the product and any installed compass. This
distance should be at least 1 m (3 ft) in all directions. For
smaller vessels it may not be possible to achieve this
distance. In this situation ensure that the compass is not
affected by the product when it is powered on.
20
81377-1-en_US_PRINT.pdf 20
12/21/2017 9:05:36 PM
3.2 EMC installation guidelines
Suppression ferrites
Raymarine® equipment and accessories conform to
the appropriate Electromagnetic Compatibility (EMC)
regulations, to minimize electromagnetic interference
between equipment and minimize the effect such
interference could have on the performance of your
system
Correct installation is required to ensure that EMC
performance is not compromised.
• Raymarine cables may be pre-fitted or supplied with
suppression ferrites. These are important for correct
EMC performance. If ferrites are supplied separately
to the cables (i.e. not pre-fitted), you must fit the
supplied ferrites, using the supplied instructions.
Note:
In areas of extreme EMC interference, some slight
interference may be noticed. Where this occurs the
product and the source of the interference should be
separated by a greater distance.
For optimum EMC performance we recommend that
wherever possible:
• Raymarine® equipment and cables connected to it
are:
– At least 1 m (3 ft) from any equipment transmitting
or cables carrying radio signals e.g. VHF radios,
cables and antennas. In the case of SSB radios, the
distance should be increased to 2 m (7 ft).
– More than 2 m (7 ft) from the path of a Radar beam.
A Radar beam can normally be assumed to spread
20 degrees above and below the radiating element.
• The product is supplied power from a separate battery
from that used for engine start. This is important to
prevent erratic behavior and data loss which can occur
if the engine start does not have a separate battery.
3.3 Product dimensions
Product dimensions - Base station
The Base station dimensions are listed below.
• If a ferrite has to be removed for any purpose (e.g.
installation or maintenance), it must be replaced in the
original position before the product is used.
• Use only ferrites of the correct type, supplied by
Raymarine or its authorized dealers.
• Where an installation requires multiple ferrites to be
added to a cable, additional cable clips should be
used to prevent stress on the connectors due to the
extra weight of the cable.
Connections to other equipment
Requirement for ferrites on non- cables.
If your is to be connected to other equipment using
a cable not supplied by , a suppression ferrite MUST
always be attached to the end of the cable near the .
The Base station includes a fitted power and data cable,
The power cable length is 1.2 m (3.94 ft) sand the Data
cable length is 420 mm (1.38 ft).
Product dimensions - speakers
The dimensions for the Passive speaker are shown
below.
• Only Raymarine® specified cables are used.
• Cables are not cut or extended, unless doing so is
detailed in the installation instructions.
Note:
Where constraints on the installation prevent any
of the above recommendations, always ensure the
maximum possible separation between different
items of electrical equipment, to provide the best
conditions for EMC performance throughout the
installation.
Installation
81377-1-en_US_PRINT.pdf 21
The Passive speaker includes a fitted 2 m (6.56 ft) audio
cable terminated with a male RCA plug.
21
12/21/2017 9:05:36 PM
Product dimensions - Raymic handset
3.4 Mounting
The Raymic handset dimensions for both cradle
mounting and clip mounting are provided.
Tools required for installation
1.
Power drill
2. Pozi-drive screwdriver
The Raymic handset is fitted with a coiled cable. Ensure
sufficient space is available below the desired mounting
area to accommodate the cable.
3.
Adhesive tape
4.
Suitable size drill bit
1. Using the supplied mounting template, mark the
location of the fixing holes on the mounting surface.
5. 89 mm (3 ½ in) Hole saw (used for speaker mounting)
2. Drill holes for the mounting fixings using a drill with
a suitable sized drill bit.
6. File (for speaker cut-out)
3. Screw the fixings approximately half way into the
holes in the mounting surface.
Mounting the Base station
4. Place the Base station over the fixings screws and
push down to lock into position.
Follow the steps below to mount the Base station.
5. Fully tighten the screws.
Before mounting the Base station ensure that you have:
6. Connect the necessary cables.
• selected a suitable location (a clear, flat surface is
required).
• identified the location for additional components, such
as the Handset or Speaker etc.
• identified the relevant cable connections and route
that the cables will take.
22
81377-1-en_US_PRINT.pdf 22
12/21/2017 9:05:36 PM
Pass-through panel kit mounting
When installing the Fistmic or the optional Raymic
handset, the pass-through panel kit should be used to
secure the cable to any panels the cable has to pass
through.
6. Place the Mounting plate gasket over the end of the
connector.
7. With the recessed side facing away from the
mounting panel, place the Mounting plate over the
end of the connector.
8. Place the lanyard end of the Splash-proof dust cap
over the connector, ensuring the lanyard sits in the
recess in the Mounting plate.
9. Place the Mounting plate nut over the connector and
tighten clockwise using a 13/16 in. (21 mm) socket
wrench, being careful not to damage the plastic nut
by overtightening.
10. Secure the Mounting plate to the mounting surface
using the supplied screws.
11. Attach the Handset / Fistmic connector to the cable
connector and rotate the locking collar clockwise to
secure.
12. Connect the opposite end of the cable to the
required connector either on the Base station or
to another pass-through panel mounting plate
connector.
Note: Drill bit, tap size and tightening torque is
dependent on the thickness and type of material the
unit is to be mounted on.
Splash-proof dust cap with lanyard
Mounting plate fixings x 3
Mounting plate nut
Raymic handset cradle mounting
Mounting plate
Before mounting the unit, ensure that you have:
Mounting plate gasket
Extension cable
• Selected a suitable location, ensuring there is nothing
behind the mounting surface that may be damaged
when drilling.
1. Check the selected location for the Mounting plate, a
clear flat area is required.
2. Using a pencil, offer up the Mounting plate to the
desired location and mark the location of the screw
holes and the center hole on the mounting panel.
3. Drill the mounting holes using a suitable size drill bit.
4. Drill the center hole using a 25 mm (1 in.) hole cutting
saw.
5. Pull the connector end of the cable through the hole
in the mounting surface.
Installation
81377-1-en_US_PRINT.pdf 23
1. Check the selected location for the mounting cradle,
a clear flat area is required, with sufficient space
around it to place and remove the Handset.
2. Using a pencil, offer up the cradle to the desired
location and mark the location of the screw holes
on the mounting surface.
3. Drill the mounting holes using a suitable size drill bit.
4. Hold the cradle in place and secure using the screws
provided.
5. Place the Handset into the cradle until it clicks into
position.
Passive speaker mounting
Follow the steps below to mount the Passive speaker.
• Identified the cable connections and route that the
cables will take.
Before mounting the Passive speaker ensure that you
have:
• selected a suitable location (a clear, flat surface is
required).
• identified the location for additional components, such
as the Handset or Base station etc.
• identified the relevant cable connections and the
route that the cables will take.
• removed the bezel.
23
12/21/2017 9:05:36 PM
1. Using the supplied mounting template, mark the
location of the cut out and fixing holes on the
mounting surface.
2. Using a 89 mm (3 ½ in) hole saw, drill out the centre
cut out area indicated on the mounting template.
3. Drill holes for the fixings, using a drill with a suitable
sized bit.
4. Ensure that the unit fits into the removed area and
then file around the cut edge until smooth.
5. Peel the backing off of the supplied gasket and place
the adhesive side of the gasket onto the rear of the
speaker, pressing firmly onto the flange.
6. Connect the relevant cable to the speaker.
7. Slide the speaker into place and secure using the
fixings provided.
8. Fit the Bezel, ensuring it clips into place on all 4 sides.
24
81377-1-en_US_PRINT.pdf 24
12/21/2017 9:05:36 PM
Chapter 4: Cables and connections
Chapter contents
•
4.1 General cabling guidance on page 26
•
4.2 Connections overview on page 26
•
4.3 Power connection on page 27
•
4.4 Handset station connection on page 29
•
4.5 Passive speaker connection on page 30
•
4.6 NMEA 2000 / SeaTalkng ® connection on page 30
•
4.7 NMEA 0183 connection on page 31
•
4.8 Loud hailer connection on page 31
•
4.9 Connecting GNSS (GPS) and VHF antennas on page 31
Cables and connections
81377-1-en_US_PRINT.pdf 25
25
12/21/2017 9:05:37 PM
4.1 General cabling guidance
Cable types and length
It is important to use cables of the appropriate type and
length
• Unless otherwise stated use only standard cables of
the correct type, supplied by Raymarine.
• Ensure that any non-Raymarine cables are of the
correct quality and gauge. For example, longer power
cable runs may require larger wire gauges to minimize
voltage drop along the run.
Routing cables
Cables must be routed correctly, to maximize
performance and prolong cable life.
• Do NOT bend cables excessively. Wherever possible,
ensure a minimum bend diameter of 200 mm (8 in) /
minimum bend radius of 100 mm (4 in).
• high current carrying AC and DC power lines,
• antennae.
Strain relief
Ensure adequate strain relief is provided. Protect
connectors from strain and ensure they will not pull out
under extreme sea conditions.
Circuit isolation
Appropriate circuit isolation is required for installations
using both AC and DC current:
• Always use isolating transformers or a separate
power-inverter to run PC’s, processors, displays and
other sensitive electronic instruments or devices.
• Always use an isolating transformer with Weather FAX
audio cables.
• Always use an isolated power supply when using a
3rd party audio amplifier.
• Always use an RS232/NMEA converter with optical
isolation on the signal lines.
• Always make sure that PC’s or other sensitive
electronic devices have a dedicated power circuit.
• Protect all cables from physical damage and exposure
to heat. Use trunking or conduit where possible. Do
NOT run cables through bilges or doorways, or close
to moving or hot objects.
• Secure cables in place using tie-wraps or lacing twine.
Coil any extra cable and tie it out of the way.
• Where a cable passes through an exposed bulkhead
or deckhead, use a suitable watertight feed-through.
• Do NOT run cables near to engines or fluorescent
lights.
Always route data cables as far away as possible from:
• other equipment and cables,
4.2 Connections overview
Connects to
GNSS (GPS)
antenna
connection
Passive GNSS
antenna
GNSS
antenna’s
fitted cable.
Earth stud
DO NOT
CONNECT
N/A
VHF antenna
connection
VHF antenna
or Splitter
VHF
antenna’s
fitted cable.
Power
and data
connection
• 12 V dc
power
supply
• Suitable
power
extension
or circuit
breaker.
Cable shielding
Ensure that all cables are properly shielded and that the
cable shielding is undamaged.
Dust caps
To prevent potential water ingress, connectors not in
use should be protected using the supplied dust caps.
Connections to other equipment
Requirement for ferrites on non-Raymarine cables
If your Raymarine equipment is to be connected to other
equipment using a cable not supplied by Raymarine,
a suppression ferrite MUST always be attached to the
cable near the Raymarine unit.
Suitable
cables
Connection
• NMEA 0183
devices
• Loud Hailer
• cable
supplied
with your
NMEA 0183
device
• Loud
hailer’s
fitted cable
26
81377-1-en_US_PRINT.pdf 26
12/21/2017 9:05:37 PM
Connection
Connects to
Suitable
cables
HS 1 (Handset
station 1)
connection
Raymic
handset or
Adaptor cable
Raymic
handset’s
fitted cable.
HS 2
(Handset
station 2)
connection
Raymic
handset or
Adaptor cable
Raymic
handset’s
fitted cable.
Hub
connection
DO NOT
CONNECT
N2K (NMEA
2000)
connection
SeaTalkng ® /
NMEA 2000
backbone
4.3 Power connection
The power supply should be connected as shown below:
In-line fuse and thermal breaker
ratings
The following in-line fuse and thermal breaker ratings
apply to your product:
In-line fuse rating
Thermal breaker rating
10 A
7 A (if only connecting
one device)
Note:
The supplied
DeviceNet to
SeaTalkng ®
adaptor
cable or a
DeviceNet
spur cable.
• The suitable fuse rating for the thermal breaker
is dependent on the number of devices you are
connecting. If in doubt consult an authorized
Raymarine® dealer.
1.
Base station
2. Power supply positive (+) Red wire
3.
Power supply negative (-) Black wire
Bare end wire connections
4.
Suitable waterproof connection (Base station is
supplied with bullet crimps on power supply wires.)
Your product is supplied with bare end wire connections.
You must ensure that ALL bare end wires are adequately
protected from short circuit and water ingress.
5. 12 V dc power source
Bare ended wire connections
It is recommended that bare ended wire connections are
made by soldering or using crimp connectors and then
protected by wrapping the connection in insulation tape.
Unused bare ended wires
Any unused bare ended wires should be folded back
and wrapped in insulation tape.
Warning: 12 Volt dc only
• Your product’s power cable may have fitted in-line
fuse, if not then you can add an in-line fuse to the
positive wire of your products power connection.
Grounding
This product is grounded through the 0 V dc negative
wire on the power cable and does not require a drain
(shield) to be connected to the base station’s ground
terminal.
This product must only be connected to a
12 volt dc power source.
Power distribution
Warning: Positive ground
systems
• The product is supplied with a power cable, either
as a separate item or a captive cable permanently
attached to the product. Only use the power cable
supplied with the product. Do NOT use a power cable
designed for, or supplied with, a different product.
Do not connect this unit to a system which
has positive grounding.
Recommendations and best practice.
• Refer to the Power connection section for more
information on how to identify the wires in your
product’s power cable, and where to connect them.
• See below for more information on implementation for
some common power distribution scenarios.
Cables and connections
81377-1-en_US_PRINT.pdf 27
27
12/21/2017 9:05:37 PM
Important:
• Ideally, all equipment should be wired to individual
suitably-rated thermal breakers or fuses, with
appropriate circuit protection. Where this is not
possible and more than 1 item of equipment shares a
breaker, use individual in-line fuses for each power
circuit to provide the necessary protection.
When planning and wiring, take into consideration
other products in your system, some of which (e.g.
sonar modules) may place large power demand
peaks on the vessel’s electrical system.
Note:
The information provided below is for guidance only,
to help protect your product. It covers common
vessel power arrangements, but does NOT cover
every scenario. If you are unsure how to provide
the correct level of protection, please consult an
authorized Raymarine dealer or a suitably qualified
professional marine electrician.
Implementation — direct connection to battery
Battery connection scenario A: suitable for a
vessel with a common RF ground point. In
this scenario, if your product’s power cable is
supplied with a separate drain wire then it should
be connected to the vessel’s common ground
point.
Battery connection scenario B: suitable for
a vessel without a common grounding point.
In this case, if your product’s power cable is
supplied with a separate drain wire then it should
be connected directly to the battery’s negative
terminal.
• The power cable supplied with your product may
be connected directly to the vessel's battery, via a
suitably rated fuse or breaker.
• The power cable supplied with your product may NOT
include a separate drain wire. If this is the case, only
the power cable’s red and black wires need to be
connected.
• If the supplied power cable is NOT fitted with an inline
fuse, you MUST fit a suitably rated fuse or breaker
between the red wire and the battery’s positive
terminal.
Implementation — connection to distribution panel
• Refer to the inline fuse ratings provided in the
product’s documentation.
Positive (+) bar
Negative (-) bar
Circuit breaker
Fuse
• In all cases, observe the recommended breaker / fuse
ratings provided in the product’s documentation.
Important:
• If you need to extend the length of the power cable
supplied with your product, ensure you observe the
dedicated Power cable extensions advice provided in
the product’s documentation.
Be aware that the suitable fuse rating for the thermal
breaker or fuse is dependent on the number of
devices you are connecting.
• Alternatively, the supplied power cable may be
connected to a suitable breaker or switch on the
vessel's distribution panel or factory-fitted power
distribution point.
Power cable extension
• The distribution point should be fed from the vessel’s
primary power source by 8 AWG (8.36 mm2) cable.
• The power cable for each unit in your system should
be run as a separate, single length of 2-wire cable
If you need to extend the length of the power cable
supplied with your product, ensure you observe the
following advice:
28
81377-1-en_US_PRINT.pdf 28
12/21/2017 9:05:37 PM
from the unit to the vessel's battery or distribution
panel.
• For power cable extensions, it is recommended that a
minimum wire gauge of 16 AWG (1.31 mm2). For cable
runs longer than 15 meters, you may need to consider
a thicker wire gauge (e.g. 14 AWG (2.08 mm2), or 12
AWG (3.31 mm2) ).
4.4 Handset station connection
A Raymic handset can be connected to each Handset
station connection (HS 1 / HS 2). Your radio is supplied
with the equipment to create a full handset station (i.e.:
Raymic handset, Adaptor cable and Passive speaker).
Additional accessories can be purchased to create a
second handset station.
Handset extension cables
Handset station cabling can be extended using
approved extension cables.
The maximum length of cable from the Handset to the
Base station should not exceed 50 m (164 ft)
• An important requirement for all lengths of power
cable (including any extension) is to ensure that there
is a continuous minimum voltage of 10.8 V at the
product’s power connector, with a fully flat battery at
11 V.
Important: Be aware that some products in your
system (such as sonar modules) can create voltage
peaks at certain times, which may impact the voltage
available to other products during the peaks.
1.
Grounding
Ensure that you observe any separate grounding advice
provided in the product’s documentation.
More information
It is recommended that best practice is observed in all
vessel electrical installations, as detailed in the following
standards:
• BMEA Code of Practice for Electrical and Electronic
Installations in Boats
• NMEA 0400 Installation Standard
Base station
2. Passive speaker (1 x supplied and available as
accessory: A80542)
3.
Raymic handset (1 x supplied and available as
accessory: A80289)
4.
Handset station adaptor cable with RCA Audio (1 x
supplied and available as accessory: A80297)
5. Raymic handset extension cable (Available optional
accessories: A80290, A80291 or A80292)
6. Panel mount fixings kit (1 x supplied and available
as a Spare: R70438)
• ABYC E-11 AC & DC Electrical Systems on Boats
• ABYC A-31 Battery chargers and Inverters
Connecting handsets and cables
• ABYC TE-4 Lightning Protection
Follow the steps below to connect handsets and
extension cables together.
1. If fitted, unscrew and remove the dust cap from the
relevant connector.
2. Ensure the cable connectors are correctly orientated,
before insertion.
3. Ensure connectors are fully inserted, before locking..
4. Tighten locking collars by Rotating clockwise.
Cables and connections
81377-1-en_US_PRINT.pdf 29
29
12/21/2017 9:05:37 PM
4.5 Passive speaker connection
A passive speaker can be connected to a handset
station using the RCA audio connector available on the
Handset adaptor cable.
4.6 NMEA 2000 / SeaTalkng ®
connection
Connecting SeaTalkng ® cables
Your product can transmit data to devices connected
on SeaTalkng ® or NMEA 2000 CAN bus networks.
Connection is established using the DeviceNet
connector located on the bottom of the unit.
Use the supplied DeviceNet to SeaTalkng ® adaptor
cable to connect your product to an available spur
connection on a SeaTalkng ® backbone.
1.
2. Alternatively you can connect your product to a
NMEA 2000 backbone using a standard DeviceNet
cable (not supplied).
1.
Raymic handset adaptor cable (1 x supplied and
available as an accessory: A80297)
2. Passive speaker (1 x supplied and available as an
accessory: A80542)
The Passive speaker includes a 2m (6.56 ft) audio cable
terminated with a Female RCA connector.
Note:
1.
The product must be connected to a correctly
terminated backbone. You cannot connect your
product directly to a MFD.
2. Refer to the instructions supplied with your
SeaTalkng ® / NMEA 2000 device for details on
creating a backbone.
1. Rotate the locking collar on the unit to the unlocked
position.
2. Ensure the cable’s connector is correctly oriented.
3. Fully insert the cable connector.
4. Rotate locking collar clockwise (2 clicks) until it is in
the locked position.
30
81377-1-en_US_PRINT.pdf 30
12/21/2017 9:05:37 PM
4.7 NMEA 0183 connection
4.8 Loud hailer connection
The NMEA 0183 wires can be used to connect the unit
to a NMEA 0183 GNSS (GPS) receiver or MFD.
A Loud hailer (M95435) can be connected to the radio
using the loud hailer wires.
Yellow = Receive positive (+) wire
Positive (+) hailer wire (Purple)
2. Green = Receive negative (-) wire
Negative (-) hailer wire (Gray)
1.
3.
White = Transmit positive (+) wire
4.
Brown = Transmit negative (-) wire
The NMEA wires should be connected to a compatible
device as shown in the table below:
NMEA 0183
device
NMEA 0183 wires
Receive positive (+)
to
Transmit positive
(+)
Receive negative (-)
to
Transmit negative
(-)
Transmit positive (+)
to
Receive positive
(+)
Transmit negative (-)
to
Receive negative
(-)
Cables and connections
81377-1-en_US_PRINT.pdf 31
31
12/21/2017 9:05:37 PM
4.9 Connecting GNSS (GPS)
and VHF antennas
The radio must be connected to suitable GNSS and VHF
antennas (not supplied). The antenna connections must
be protected so it cannot come into contact with any
grounded bare metal.
Pre-requisites:
• Ensure you have installed your antennas in
accordance with the instructions supplied with the
antennas.
• Ensure the cables have been properly routed to
the Base station and that sufficient cable length is
available to make the connections.
1. Plug the antenna connector into the relevant antenna
connection on the Base station.
2. Secure by tightening the locking collars.
32
81377-1-en_US_PRINT.pdf 32
12/21/2017 9:05:37 PM
Chapter 5: Getting started
Chapter contents
•
5.1 Raymic handset controls on page 34
•
5.2 Powering the Base station on page 34
•
5.3 Homescreen overview on page 35
•
5.4 Shortcut list on page 37
•
5.5 Shared Brightness on page 37
•
5.6 Initial startup on page 38
•
5.7 Selecting a language on page 38
•
5.8 Switching on the AIS receiver on page 39
•
5.9 Selecting a network type on page 39
•
5.10 Entering your MMSI number on page 39
•
5.11 Entering your ATIS ID on page 40
•
5.12 Changing the radio region on page 41
•
5.13 Switching between high and low transmit power on page 41
•
5.14 GNSS (GPS) set up on page 42
Getting started
81377-1-en_US_PRINT.pdf 33
33
12/21/2017 9:05:37 PM
5.1 Raymic handset controls
The Raymic handset’s controls are shown below.
11. Channel Up and Channel Down — Changes the
channel up or down.
12. VOL/SQ — Press button to switch between volume
and squelch control.
13. Built-in speaker
5.2 Powering the Base station
The Base station automatically powers up when
connected to a suitable power supply.
The Base station is powered down by unplugging from
the power supply or, if applicable, by tripping it’s circuit
breaker.
Powering the handset
With the Base station powered On and the Handset
connected:
1.
Power — Press to power the handset on. Press
and hold for 3 seconds to power the handset off.
Momentary press to access the shortcut list.
2. PTT(Push to Talk) — Press and hold to send a voice
message. Release to return to receive mode.
Note: The maximum transmit time is limited to 5
minutes to prevent un-intentional transmissions
from occupying the VHF channel.
3.
Microphone location
4.
Volume Up and Volume Down — Press to adjust
volume or squelch up or down.
1. Press the Power button, located on the top of the
Handset.
The Handset will power on.
2. To power off the Handset, press and hold the Power
button for approximately 3 seconds, until the screen
turns off.
5. LCD screen
6. Back — Move back through menu options.
7.
OK / menu button — Press button to access menu /
DSC functions and to confirm selections.
8. 16 / + — When powered on press to switch between
priority channels.
9.
HI/LO — Press to switch between High (25 W) and
low (1 W) transmit power.
10. DISTRESS — Lift up the spring loaded cover and
press this button to make a DSC distress call.
34
81377-1-en_US_PRINT.pdf 34
12/21/2017 9:05:37 PM
5.3 Homescreen overview
The information below describes the on-screen
characters and symbols which the radio displays on the
main screen and what they mean.
5. Channel — Indicates the current channel number.
6. Location / Time or Location / COG/SOG —
Depending on selection displays Location
coordinates and current time or Location
coordinates and current COG and SOG.
7.
Channel Name — Indicates the name of the current
channel.
Symbol
Name
Description
Fog horn
Indicates that the
radio is in Fog
horn mode.
Transmit
Indicates the
radio is currently
transmitting (e.g.
the PTT button is
being pressed.)
Receive
Indicates the
radio is currently
receiving a
transmission
Weather
Indicates that the
weather alerts
mode is activated.
Power supply
voltage too low
Indicates the
power supply to
the radio is below
the specified
operating voltage
Power supply
voltage too high
Indicates the
power supply to
the radio is above
the specified
operating voltage
8. Channel type — Indicates the type of channel:
• s = Simplex — Simplex channels transmit and
receive on the same frequency.
• d = Duplex — Duplex channels use separate
frequencies to transmit and receive.
9.
Optional text — Provides extra user guidance.
Status bar symbols
1.
Status bar — The status bar displays symbols which
indicate the current status of the unit.
2. Frequency band — Indicates which channel
frequency band is in use:
• USA — United States of America
The status bar is used to display icons that indicate the
radio’s status.
Symbol
Name
Description
Low power
Indicates the radio
transmitters is in
low power (1 watt)
or high power (25
watt) mode
• INT — International
• CAN — Canada
• WX — Weather
Note: Special licensing is required to receive
USA and Canadian channel sets.
3.
Status text — Indicates the current radio mode e.g.:
ATIS Mode active, Weather Alert, Scan mode etc.
4.
Channel suffix
• a — Indicates that the current US or Canadian
channel is simplex. This channel uses the
transmit frequency of the International channel for
transmitting and receiving. If a channel is simplex
in all 3 frequency bands (e.g. channel 06, the
channel does not require the a suffix.
• b — Indicates that the channel is a receive only
channel. Used for Canadian channels only.
Getting started
81377-1-en_US_PRINT.pdf 35
High power
Local
Indicates the
radio is in local
reception mode,
which decreases
receiver
sensitivity in
high traffic areas
to decrease
unwanted
reception
35
12/21/2017 9:05:37 PM
Symbol
Name
Description
DSC
Indicates that a
DSC call has been
received
Symbol
Name
Sub-options
* DSC Calls
• Individual call
• Distress call
Symbol
Name
Sub-options
** Hail/Fog/Intercom
• Hailer
• Position
request
GPS Fix
Indicates if the
radio has a
GPS/GNSS fix.
• Group call
• Fog horn
• Intercom
** Hailer/Fog
horn
• Hailer
** Intercom
• Intercom
Set-up
• Display set-up
• All ships call
• Fog horn
• Phonebook
• Call logs
Main menu overview
• Test call
The main menu is accessed by Pressing the OK button
from the Homescreen.
• DSC set-up
* Watch Mode
• Dual watch
• Triple watch
• 2nd priority
channel
* Weather Mode
• Weather
Homescreen
• Language
• Units
• Power output
• Sensitivity
• Key beep
* Scan Mode
1.
Currently selected menu item
2. Scroll bar
3.
Menu items
The main menu includes the following items:
• All channels
• Channel
set-up
• All channels +
16
• Weather alerts
• Saved
channels
• DSC set-up
• Saved
channels + 16
• Edit saved
channels
• GPS set-up
• AIS
• Network
output
• ATIS set-up
• Maintenance
36
81377-1-en_US_PRINT.pdf 36
12/21/2017 9:05:37 PM
Note:
* Menu items not available when radio has ATIS
enabled or if the radio has been pre-programed in
MARCOM-C mode.
** The menu name and sub-options depend on the
peripheral devices connected to the radio.
5.4 Shortcut list
5.5 Shared Brightness
Pressing the Power button once while the radio is
switched on will open the Shortcuts list. The Shortcuts
list can be used to adjust the brightness, contrast and
access frequently used functions.
You can set up Shared Brightness groups which enables
simultaneous brightness adjustment the all units that
are part of the same group.
The following products are compatible with Shared
Brightness:
• LightHouse™ or LightHouse™ 2 powered MFDs.
• SeaTalkng ® Instrument displays and Pilot controllers.
• SeaTalkng ® VHF DSC Radios.
Any adjustments to the Shared Brightness level will be
reflected on all units assigned to the same group.
LightHouse™ MFD
Instrument display /
Pilot controller
Frequently used functions can be added by selecting
Add/edit shortcuts.
Adjusting Brightness and Contrast
The LCD Brightness (Backlight) and Contrast can be
adjusted using the Shortcuts list.
VHF DSC Radio
From any screen:
1. Press the Power button.
2. Select Backlight or Contrast.
3. Use the Rotary knob to adjust the Backlight or
Contrast to the desired level.
4. Press the Back button to return to the previous
screen.
The Backlight and Contrast settings can also be
accessed from the Display set-up menu: Menu > Set-up
> Display set-up .
Multiple brightness groups can be configured. These
groups could be used to reflect the physical location of
units on your vessel. For example, the units at your helm
can be set to one group, and the units on the flybridge
can be set to a different group.
Shared Brightness requires:
• all units to be compatible with the Shared Brightness
function (see list of compatible units above).
Getting started
81377-1-en_US_PRINT.pdf 37
37
12/21/2017 9:05:37 PM
• the Share brightness setting set to On for all units
in the brightness group.
• units to be assigned to Network Groups.
• all the displays in that group to be synchronized.
Enabling Shared Brightness
5.6 Initial startup
5.7 Selecting a language
Unless your radio has been pre-programmed; the first
time you power-up your radio you will be requested to
select certain options. With the exception of your MMSI
and ATIS ID, you will also be requested to enter these
options after a factory reset.
The language the radio uses can be changed.
From the Display Set-up menu: (Menu > Set-up >
Display Set-up).
After acknowledging the startup screen, unless
previously set you will be prompted to make the
following selections:
1. Select Shared Brightness.
1.
2. Select Shared Brightness again to enable Shared
Brightness.
If Shared Brightness is already enabled then
selecting this menu item will disable Shared
Brightness.
3. Select Group.
Language selection — See 5.7 Selecting a language
for available languages.
2. Turn on AIS reception (Ray70 and Ray91 only) —
Enables the built-in AIS receiver. This step is only
applicable to radios with a built-in AIS receiver.
See 5.8 Switching on the AIS receiver for more
information.
3.
4. Select the group that you want to assign the radio to.
Adjusting the Brightness setting will now change the
brightness of all products assigned to that group.
4.
Select network type — Selects which connection to
transmit AIS and DSC information on, to connected
equipment. This step is only applicable if the AIS
receiver was turned on in the previous step. See 5.9
Selecting a network type for available options.
From the Main menu:
1. Select Set-up.
2. Select Language.
The languages available are:
• English (default) — English
• Español — Spanish
• Français — French
• Deutsch — German
• Italiano — Italian
3. Select the language that you want the radio to be
set to.
The User interface language is changed to the selected
language.
Enter MMSI number — Required to enable DSC
functions. This option is not required after a factory
reset, or if the radio has been pre-programed in
MARCOM-C mode, or has ATIS enabled. See 5.10
Entering an MMSI number for more information. If
not already selected you will also be prompted to
select your network type.
5. Enter ATIS ID — Required when the radio will be
used in the inland waterways of Europe. This step is
only applicable if the radio has been pre-programed
in MARCOM-C mode. See 5.11 Entering an ATIS ID
for more information.
6. Frequency band selection — Sets the relevant
channels for your region. This step is not applicable
if the radio has been pre-programed in MARCOM-C
mode. See 5.12 Changing the radio region for more
information.
38
81377-1-en_US_PRINT.pdf 38
12/21/2017 9:05:37 PM
5.8 Switching on the AIS
receiver
If your radio includes a built-in AIS receiver then it can
be enabled and disabled as follows:
From the Main menu:
1. Select Set-up.
2. Select AIS.
3. Select On to switch the receiver on, or select Off to
switch the receiver off.
5.9 Selecting a network type
When connecting your radio to other devices it is
important to ensure you select the network connection
and type that you want data to be transmitted over.
5.10 Entering your MMSI
number
To program your radio with your MMSI number follow
the steps below.
From the Main menu:
1. Select Set-up.
2. Select Network output.
The following network types are available:
• NMEA 2000 (default)
• 0183 High speed
• 0183 Std speed
3. Select the network type relevant to the devices
connected to your radio. If your radio is not
connected to any other devices any option can be
selected.
Selecting 0183 Std speed will disable the built-in AIS
receiver, where applicable.
The Network output setting determines the baud rate
of the NMEA 0183 input:
Network output setting
NMEA 0183 input baud
rate
NMEA 2000
Standard speed (4,800)
NMEA 0183 High Speed
High speed (38,400)
NMEA 0183 Standard
Speed
Standard speed (4,800)
From the Set-up menu: (Menu > Set-up)
1. Select DSC set-up.
2. Select MMSI.
The MMSI required message will be displayed if no
MMSI number has been set.
3. Select Yes .
4. Use the Rotary knob to cycle through the available
numbers and press OK to confirm each number and
move to the next digit.
You should only enter the unique 9 digit MMSI
number provided by your licensing authority.
MMSI numbers starting with a ‘0’ are only used for
groups and coast stations. If you enter a ‘0’ as the
first digit the radio will assume you are entering a
coast station MMSI and automatically assign a ‘0’ as
the second digit; this is to ensure a group MMSI is
not entered as the radio’s unique MMSI.
5. Press the Back button at any time to edit digits you
have already entered.
6. Press and hold the OK button to display options to
Move cursor back and forward through the digits.
Getting started
81377-1-en_US_PRINT.pdf 39
39
12/21/2017 9:05:37 PM
7. When the final digit is confirmed select DONE.
Example
8. The MMSI is displayed onscreen, check that it is
correct, then:
i. Select Yes – Save, or
ii. if the number entered is not correct select No –
Retry.
Caution: MMSI and ATIS ID
entry
You can only enter the MMSI number and
ATIS ID once!
If you store an incorrect MMSI number or
ATIS ID in your product, it will have to be
reset by an authorized Raymarine® dealer.
5.11 Entering your ATIS ID
A unique ATIS ID must be entered before ATIS mode
can be enabled.
From the Main menu.
1. Select Set-up.
2. Select ATIS set-up.
3. Select ATIS ID.
Not set will be displayed if no ATIS ID has been set.
The first digit is set to a ‘9’ and cannot be changed,
this is because all ATIS IDs start with a ‘9’.
As most ATIS IDs consist of a ‘9’ followed by your 9
digit MMSI number; if your radio already has an MMSI
number the ATIS ID will be pre-filled in this format.
4. If the ATIS ID has been pre-filled, check it carefully
against your issued ATIS ID.
5. To enter your ATIS ID manually, use the Rotary knob
to cycle through the available numbers and press OK
to confirm each number and move to the next digit.
You should only enter the unique 10 digit ATIS ID
provided by your licensing authority.
6. Press the Back button at any time to edit digits you
have already entered.
7. Press and hold the OK button to display options to
Move cursor back and forward through the digits.
8. When the final digit is confirmed select DONE.
Example
9. The ATIS ID is displayed onscreen, check that it is
correct, then:
i. Select Yes – Save, or
ii. if the number entered is not correct select No –
Retry.
Caution: MMSI and ATIS ID
entry
You can only enter the MMSI number and
ATIS ID once!
If you store an incorrect MMSI number or
ATIS ID in your product, it will have to be
reset by an authorized Raymarine® dealer.
Enabling and disabling ATIS mode
ATIS is a European system used on some inland
waterways. A unique ATIS ID must be entered to use
ATIS mode.
With ATIS mode enabled the radio’s region will be
fixed to the INT (international) frequency band and the
following functions are disabled:
• DSC functions
• Watch Mode
• Scan Mode
40
81377-1-en_US_PRINT.pdf 40
12/21/2017 9:05:37 PM
• High/low power is restricted on certain channels
From the Main menu.
5.12 Changing the radio region
1. Select Set-up.
Prior to using the radio you must set the Frequency band
to the region your radio will be used in.
2. Select ATIS set-up.
From the Main menu:
3. Select ATIS.
5.13 Switching between high
and low transmit power
You can switch between high (25 W) and low (1 W)
transmit power using the HI/LO button on the Fistmic.
The transmit power can also be changed from the
Set-up menu: Menu > Set-up
If no ATIS ID has been set then you will be requested
to enter one before ATIS mode is enabled refer to
5.11 Entering your ATIS ID for instructions.
1. Select Power output.
2. Select Low for 1 W transmit power, or
4. If an ATIS ID has already been set then select On to
enable ATIS mode or Off to disable ATIS mode.
3. Select High for 25 W transmit power.
1. Select Set-up.
2. Select Channel set-up.
3. Select Frequency band.
4. Select the relevant region from the list.
The available options are:
• International
• USA
• Canada
An icon is displayed on the Homescreen that identifies
which region has been set.
Getting started
81377-1-en_US_PRINT.pdf 41
41
12/21/2017 9:05:37 PM
5.14 GNSS (GPS) set up
If your radio includes an internal GNSS (GPS) receiver or
if your radio is connected to a receiver over NMEA 0183
or SeaTalkng ®, the radio can display relevant position
information.
The following information can be displayed:
• latitude
• longitude
• UTC time
• COG and SOG
When position data is available the satellite icon is
displayed onscreen.
If no position data is available then the latitude, longitude
and time can be entered manually so that it can be
included in DSC distress transmissions.
Position data received from other vessels can be
displayed on a connected Raymarine® multifunction
display.
Enabling and disabling the internal
GNSS (GPS)
From the GPS set-up menu: Menu > Set-up > GPS
set-up
1. Select Internal GPS.
Selecting Internal GPS will switch the internal GNSS
(GPS) receiver On and Off.
No GPS position data
If no GPS data is available or GPS data becomes
unavailable; after 10 minutes an audible warning is
sounded, the GPS icon flashes and the No position data
message is displayed.
Once the warning has been acknowledged the GPS
icon will continue to flash. The No position data
warning is repeated every 4 hours if position data is still
unavailable, has not been entered manually or has been
entered manually but over 23.5 hours ago.
If position data has been entered manually the display
alternates between displaying the manual position and
time and the Manual Position message. if the manually
entered position has not been updated in the last 4
hours the GPS icon flashes and an audible warning is
sounded. This warning will be repeated every 4 hours
until position is manually updated or GPS position data
becomes available.
Where no position data is available or has not been
manually updated for 23.5 hours then position data will
change to ‘9’s and time will change to ‘8’s.
Setting time format and offset
You can change the Format and Offset that is applied to
the time displayed onscreen.
From the Units menu: Menu > Set-up > Units.
1. Select Time format.
2. Select the desired format:
• 12 hour
Entering position manually
If GPS position data is not available it can be entered
manually.
• 24 Hour (default)
3. Select Time offset.
From the GPS set-up menu: Menu > Set-up > GPS
set-up.
4. Adjust the offset to the desired value using the
Rotary knob or the Channel Up and Channel Down
buttons.
1. Select Set manual position.
5. Select OK to confirm the selection.
The Manual position screen requires you to input
latitude, longitude and UTC time.
2. Use the Rotary knob to cycle through the available
numbers and press OK to confirm each number and
move to the next digit.
3. When the relevant information has been entered
select OK to confirm the details.
Selecting GPS information to display
You can change the GPS data that is displayed on the
Homescreen.
From the GPS set-up menu: Menu > Set-up > GPS
set-up.
1. Select Homescreen display.
2. Select the required option:
• Location & time
• Location & COG/SOG
The Homescreen display option is also available from
the Display set-up menu
42
81377-1-en_US_PRINT.pdf 42
12/21/2017 9:05:37 PM
Chapter 6: Digital selective calling (DSC)
Chapter contents
•
6.1 Digital Selective Calling (DSC) on page 44
•
6.2 Distress calls on page 45
•
6.3 Urgency calls on page 47
•
6.4 Safety calls on page 48
•
6.5 Individual (routine) calls on page 48
•
6.6 Group calls on page 49
•
6.7 Position requests on page 49
•
6.8 Phonebook on page 50
•
6.9 Call logs on page 51
•
6.10 Test calls on page 51
•
6.11 DSC set-up menu options on page 52
Digital selective calling (DSC)
81377-1-en_US_PRINT.pdf 43
43
12/21/2017 9:05:37 PM
6.1 Digital Selective Calling
(DSC)
Traditional VHF radio systems require users to listen
until someone speaks, and then determine whether the
call is for them. DSC ensures that calls are received by
alerting or announcing the intended recipient(s) first so
they are ready to listen to the subsequent message on
the relevant channel.
DSC is part of the Global Maritime Distress and Safety
System (GMDSS), a maritime communications system
for emergency and distress messages and all types
of routine communications such as ship-to-ship or
ship-to-shore.
DSC is a digital signalling system, which operates on
VHF channel 70. DSC calls include other data such as
your vessel’s identification number, purpose of the call,
your position and the channel you want to speak on.
DSC calls can be divided into 4 categories and are
prioritized as shown below:
1.
Distress
2. Urgency
3.
Safety
4.
Routine
Distress
A Distress call should only be used when there is
imminent danger to a vehicle or person that requires
immediate assistance.
When making a distress call the following information is
transmitted to all stations within range:
• Vessel MMSI number.
• Vessel position (must be input manually if no GPS
position data is available).
• Local time (must be input manually if no GPS position
data is available).
• Nature of the distress (when designated).
• Transmission frequency.
The call is automatically repeated at approximately 4
minute intervals until it is acknowledged either by a
coast radio station (CRS) or a vessel within radio range.
Distress calls must be followed by a MAYDAY call on
priority channel 16.
Urgency
An urgency call should be used when there is danger
to a vehicle or person that does not require immediate
assistance.
When making an urgency call the following information
is transmitted to all stations within range:
• Vessel MMSI number.
• Vessel position (must be input manually if no GPS
position data is available).
Routine calls are made on channel 70 using the
dedicated Maritime Mobile Service Identity (MMSI)
number of the station to be contacted, selecting a
VHF working channel and sending the call. Both
radios automatically switch to the chosen channel for
conversation.
Routine calls can also be made to groups — When
groups of ships need the same information (yacht races,
club rallies etc.) a special group-call identity can be used
to enable restricted broadcast calls.
Note: To transmit precise positions, the radio must
be interfaced to a GPS receiver. Otherwise, regular
manual position updating is required.
• Local time (must be input manually if no GPS position
data is available).
• Transmission frequency.
Once an urgency call is sent it must be followed with
a PAN PAN voice message on channel 16 and include
the necessary details.
Safety
A safety call should be used when there is an
important navigational warning or meteorological
forecast/broadcast. Safety alerts can also used for
communications during search and rescue operations.
When making a safety call the following information is
transmitted to all stations within range:
• Vessel MMSI number.
• Vessel position (must be input manually if no GPS
position data is available).
• Local time (must be input manually if no GPS position
data is available).
• Transmission frequency.
Once a safety call is sent it must be followed with a
SECURITE voice message on channel 16 and include
the necessary details.
Routine calls
Routine calls are used for contacting other vessels,
marinas, or shore stations.
44
81377-1-en_US_PRINT.pdf 44
12/21/2017 9:05:37 PM
6.2 Distress calls
Making a distress call
Making a designated distress call
In an emergency you can use your unit to make an
automatic DSC distress call.
When making a Distress call you can specify the nature
of the distress, if GPS data is not available you must also
specify your coordinates.
Making a Mayday call
In an emergency you can use your unit to make a
Mayday call.
1. Press the 16 PLUS button.
2. Press and hold the PTT button.
From the Distress call menu: Menu > DSC Calls >
Distress calls
3. Slowly and clearly speak the details of the distress:
MAYDAY, MAYDAY, MAYDAY
1. Select a distress type from the list.
This is 
• Undesignated
MAYDAY 
• Fire
My position is 
• Flooding
• Grounding
• Listing
1. Press and hold the DISTRESS button for 3 seconds.
Once the DISTRESS button is pressed a 3 second
count down will begin, when the count down reaches
zero the DSC distress call is transmitted.
• Sinking
• Adrift
The distress call is repeated automatically until it is
acknowledged.
• Abandoning
• Piracy
• Man overboard
If your radio has a GPS fix then the distress type and
coordinates are displayed, otherwise you will be
prompted to enter your position coordinates.
2. If prompted, enter your position coordinates and
local time using the Rotary knob or the Channel Up
and Channel Down buttons to enter the relevant
details.
3. When complete press the OK button.
4. Follow the steps for Making a Distress Call to transmit
the distress alert.
Digital selective calling (DSC)
81377-1-en_US_PRINT.pdf 45
OVER
3. Release the PTT button.
With the spring loaded cover open:
Note: Your radio must have an MMSI number saved
before DSC functions can be used.
• Collision
I REQUIRE IMMEDIATE ASSISTANCE
2. Press and hold the PTT button, then slowly and
clearly speak the details of the distress in the
following format:
MAYDAY, MAYDAY, MAYDAY
This is 
I am 
I have 
I REQUIRE IMMEDIATE ASSISTANCE
OVER
4. Release the PTT button.
5. If an acknowledgement is not received then repeat
steps 2 to 4 above.
Cancelling a distress call before
transmission
MAYDAY 
To cancel a distress call before it is transmitted follow
the steps below:
My position is 
1. Release the DISTRESS button before the countdown
timer completes.
I am 
When the button is released you will be returned to
normal operation.
I have 
45
12/21/2017 9:05:37 PM
Cancelling a distress call after
transmission
Cancel my distress alert of , 

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Compression Level               : 6
Compression Type                : auto
Config File                     : C:\Program Files\PTC\Arbortext Editor\lib\standard.pdfcf
Create Date                     : 2017:12:21 18:13:25Z
Creator                         : PTC Arbortext Editor with Styler
EPS Processor                   : PStill version 1.84.36
Graphics Resolution             : 600
Graphics Resolution Threshold   : 900
JPEG Quality                    : 80
Modify Date                     : 2018:02:15 10:38:31-08:00
PTC Arbortext Build             : R61M080-1026
Print Engine                    : Arbortext FOSI Print Publisher
Stylesheet                      : C:\Users\awilman\Work Folders\Desktop\stylesheets\UPGRADED\RYM 2017 A5 landscape handbook 3-column small Proxima Nova font.style
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Compression 0020level           : 6
Compression 0020type            : auto
Config 0020 File                : C:\Program Files\PTC\Arbortext Editor\lib\standard.pdfcf
EPS0020processor                : PStill version 1.84.36
Graphics 0020resolution         : 600
Graphics 0020resolution 0020threshold: 900
JPEG0020quality                 : 80
PTC0020 Arbortext 0020 Build    : R61M080-1026
Print 0020 Engine               : Arbortext FOSI Print Publisher
Creator Tool                    : PTC Arbortext Editor with Styler
Metadata Date                   : 2018:02:15 10:38:31-08:00
Producer                        : PDFlib+PDI 9.0.3p4 (Win32)
Format                          : application/pdf
Document ID                     : uuid:f6c710e1-5720-4440-a042-cdbcc163a605
Instance ID                     : uuid:2374a2c1-c092-4e98-8a4b-90515b71edf7
Page Layout                     : SinglePage
Page Count                      : 107
EXIF Metadata provided by EXIF.tools
FCC ID Filing: PJ5-RAY90

Navigation menu