Flir BelgiumBA STNGB Low-power (unlicensed) wireless device for leisure User Manual 87086 1

Raymarine UK Ltd. Low-power (unlicensed) wireless device for leisure 87086 1

Gseries Base Station

Download: Flir BelgiumBA STNGB Low-power (unlicensed) wireless device for leisure User Manual 87086 1
Mirror Download [FCC.gov]Flir BelgiumBA STNGB Low-power (unlicensed) wireless device for leisure User Manual 87086 1
Document ID898570
Application ID2xpPhprHrBq2krPFpOda0Q==
Document DescriptionGseries Base Station
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize73.62kB (920293 bits)
Date Submitted2008-02-05 00:00:00
Date Available2008-02-05 00:00:00
Creation Date2007-10-04 08:48:40
Producing SoftwareAcrobat Distiller 7.0.5 (Windows)
Document Lastmod2007-10-04 08:52:50
Document Title87086_1.book
Document CreatorPScript5.dll Version 5.2.2
Document Author: asimpson

Document number: 87086-1
Date: October 2007
DO NOT use acid, ammonia based or abrasive
products.
DO NOT use commercial high pressure washing
(jet wash) equipment.
Cleaning
This product contains no user serviceable
components. Please refer all maintenance and
repair to authorized Raymarine dealers.
Unauthorized repair may affect your warranty.
Service and maintenance
This equipment must be installed and operated in
accordance with the Raymarine instructions
provided. Failure to do so could result in poor
product performance, personal injury, and/or
damage to your boat.
Product installation
Installation instructions
G-Series control keyboard
Wireless base station
87086_1.book Page 1 Thursday, October 4, 2007 8:47 AM
Raymarine UK Ltd. hereby declares that the G-Series Control Keyboard and Wireless
base station are in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC.
The original Declarations of Conformity may be viewed on the relevant product pages at
www.raymarine.com.
Declaration of Conformity
The G-Series control keyboard and wireless base station comply with US CFR47 part
15 Rules and with IC Standard RSS210. Operation is subject to the following two conditions: (1) these devices may not cause harmful interference and (2) these devices must
accept interference received, including interference that may cause undesired
operation.
Changes or modifications to these devices not expressly approved in writing by Raymarine could violate compliance with FCC or IC rules, and void the user's authority to
operate the equipment.
FCC and Industry Canada Information
Raymarine equipment and accessories conform to the appropriate Electromagnetic
Compatibility (EMC) regulations. This minimizes electromagnetic interference between
equipment, which could otherwise affect the performance of your system.
Correct installation is required to ensure that EMC performance is not compromised.
EMC installation guidelines
The technical and graphical information contained in this document, to the best of our
knowledge, was correct as it went to press. However, our policy of continuous improvement and updating may change product specifications without prior notice. As a result,
unavoidable differences between the product and handbook may occur from time to
time. Raymarine cannot accept responsibility for any inaccuracies or omissions it may
contain. For the latest product information visit our website - www.raymarine.com
Disclaimer
The Waste Electrical and Electronic Equipment (WEEE) Directive requires
the recycling of waste electrical and electronic equipment. Whilst the WEEE
Directive does not apply to some of Raymarine’s products, we support its
policy and ask you to be aware of how to dispose of this product.
The crossed out wheeled bin symbol, illustrated above, and found on our
products signifies that this product should not be disposed of in general
waste or landfill.
Please contact your local dealer, national distributor or Raymarine Technical
Services for information on product disposal.
Waste Electrical and Electronic Equipment Directive
87070
87084
87085
86126
81276
G-Series system installation & commissioning
instructions
G-Series command center keyboard installation
instructions
G-Series command center keyboard wireless upgrade
kit installation instructions
G- Series system operating guide
G-Series system user reference guide
87070-1 G-Series system installation guide
Page 20. System shown has one keyboard base station serving 2
keyboards, where 2 base stations are actually required. Each
keyboard requires a dedicated base station.
The documents supplied with the G-Series system contain a small
number of known errors:
Errata
Additional documents
You may also refer to separate instructions provided with the associated ancillary equipment.
Part number
Title
G-Series system documentation
This installation guide contains information required to successfully
install and set up your wireless base station.
It is part of a series of documents associated with the G-Series
system. All documents can be downloaded from:
www.raymarine.com/handbooks.
Handbook information
87086_1.book Page 2 Thursday, October 4, 2007 8:47 AM
Site Survey
Mount base station in selected location.
Make all connections into equipment.
MOUNTING & CONNECTION
We strongly recommend that you produce a complete schematic diagram for
your G-Series installation. Refer to the G-Series system installation and commissioning instructions for templates and further information.
Charge keyboard
Plan system layout
Check pack contents
PLANNING
Installation of the wireless keyboard system requires a structured
and planned approach. Use the following sequence of tasks:
Installation sequence
Page 41 & 42. Connection shows keyboard connected via ST70
instrument. Keyboards must be connected to a dedicated T-piece.
Page 65. Repeat base stations. These are not available for the wireless keyboard.
E02045
A06043
A06033
A06028
Wireless base station
1 m (3.3 ft) SeaTalk NG spur cable - stripped ends
400 mm (15.75 in) SeaTalkng backbone cable
SeaTalk NG T-connector
SeaTalk T connector
Part No.
wireless basestation
SeaTalkng
Description
SeaTalkng spur cable
SeaTalkng backbone cable
Wireless base station
Check pack items
Basestation
Monitor
ENTER
PAGE
MOB
WPTS
DATA
PILOT
MENU
OK
CANCEL
OUT
IN
RANGE
Charge
point
SeaTalkng
bulkead mounting
cable
SeaTalkng charge cable
STANDBY
ACTIVE
DODGE
SeaTalkng spur
WXYZ
MNO
DEF
JKL
TUV
ABC
PQRS
GHI
Keyboard
GPM400
SeaTalkng backbone
The base station and wireless keyboard are installed as a part of the
Raymarine G-Series system.
Typical system layout
Plan wireless keyboard system
SeaTalkng spur
87086_1.book Page 3 Thursday, October 4, 2007 8:47 AM
D10069-2
D10067-2
Part No
A06044
3 m (9.8 ft)
SeaTalkng spur cable (bare ends)
12 Vdc to SeaTalkng
A06049
R08310
3 m (9.8 ft)
SeaTalkng bulkhead mounting
cable
SeaTalkng power
R08311
2.5 m (8.2 ft)
charging cable
Keyboard charging
A06043
1 m (3.3 ft)
SeaTalkng spur cable (bare ends)
Wireless base station to SeaTalkng
Cable
Included with the wireless
upgrade kit.
Included with wireless base
station.
Notes
Wireless keyboard & base station cables
3. When connecting a keyboard to the system, record its details
on your system diagram. You will need this information
during commissioning. (Refer to the separate G-Series
system installation instructions for sample diagrams.)
2. You should have at least one permanently wired keyboard.
In the event that any wireless keyboards are lost, the wired
keyboard can be used to control the system.
Notes:
1. Each keyboard and base station communicate as a dedicated pair.
87086_1.book Page 4 Thursday, October 4, 2007 8:47 AM
•
G-Series Keyboard rear
SeaTalkng power cable
D10688-1
For information on the keyboard battery and charge point. Refer
to separate instructions supplied with the wireless upgrade kit.
See also
SeaTalkng spur
12 V dc,
5 A fuse supply
SeaTalkng backbone
Charge for 6 hours
Before proceeding with the installation you must charge the
keyboard. If the SeaTalkng wiring is not installed, you will need to
create a temporary keyboard connection with power as shown.
Charge keyboard
Install in a dry area below decks.
Mount on a vertical surface.
Install the unit well away from potential sources of ignition.
Mount at least 1 m (3 ft) away from devices which may be affected by radio transmission (e.g. compass).
•
•
•
•
Location
Select a location likely to provide the required wireless coverage.
E.g. In the immediate vicinity of single / co-located nav stations or
mid-way between remotely located nav stations.
Do NOT install near sources of heat or vibration. (e.g. engine).
•
Mounting and environment
A site survey is required to select the appropriate location for your
wireless base station. You must repeat the site survey for each
keyboard / base station pair.
Site survey
87086_1.book Page 5 Thursday, October 4, 2007 8:47 AM
ENTER
DEF
WXYZ
PAGE
MOB
WPTS
STANDBY
ACTIVE
DODGE
DATA
PILOT
MENU
OK
CANCEL
OUT
IN
RANGE
Wired keyboard
MNO
JKL
TUV
ABC
PQRS
GHI
Monitor
Flybridge
WXYZ
MNO
DEF
TUV
JKL
ABC
PQRS
GHI
MOB
WPTS
STANDBY
ACTIVE
DODGE
PAGE
Monitor
DATA
PILOT
MENU
OK
CANCEL
OUT
IN
RANGE
DEF
WXYZ
MNO
JKL
TUV
ABC
GHI
PQRS
PAGE
MOB
WPTS
STANDBY
ACTIVE
DODGE
DATA
PILOT
MENU
OK
Monitor
CANCEL
IN
RANGE
OUT
D10687-1
Wireless basestation
Monitor
Wireless Basestation
Wireless keyboard
ENTER
Saloon
Wireless keyboard
ENTER
Bridge
Temporary
power
connection
Power cable
Wireless
basestation
Black
Red
Screen
D10689-1
12 V dc,
5 A fuse supply
Connect power to base station
Site the base station at the required location and make a temporary
switched connection to the power supply.
You must survey the wireless coverage to ensure that each wireless
keyboard can operate in the intended area.
Check wireless coverage
87086_1.book Page 6 Thursday, October 4, 2007 8:47 AM
Check signal strength
1. Press the button (located under the outer cover of the base
station) to initiate site survey mode.
2. Slowly move the keyboard around the required area of the
vessel, confirming that the signal strength indicator maintains a
strong signal (i.e 3 bars).
3. If the signal strength is not maintained, re-position the base
station and repeat the survey.
4. Turn off the base station once the survey is complete.
The keyboard is now registered.
Note: It is important that NO additional wireless keyboards or base
stations are turned on during registration. This will prevent
accidental registration of the wrong device or base station.
e.g.
5. Once the base station is detected, the keyboard display shows
the signal strength.
Register Keyboard to base station
Register an unregistered keyboard to the required base station.
1. Turn off all base stations and keyboards within range.
2. Turn on the appropriate base station.
3. Within one minute turn on the unregistered keyboard.
(This must be within range of the base station.)
4. The keyboard attempts to register.
66 mm (2.6 in)
Wireless base station mounting
36 mm (1.42 in)
Mounting and connection
87086_1.book Page 7 Thursday, October 4, 2007 8:47 AM
117 mm (4.61 in)
Ve ount
rtic
all
D10203-2
White
Black
Red
Screen
Blue
D10208-1
For information on the wireless keyboard and charge cables, refer to
the separate instructions supplied with the wireless upgrade kit.
Keyboard and charge cable installation
There are no repeat base stations for the wireless keyboard.
Repeat base station
SeaTalkng
connection
Wireless
basestation
Wireless base station connections
Tel: +1 603.881.5200
Fax: +1 603.864.4576
Tel: +44 (0) 23 9269 3611
Fax: +44 (0) 23 9269 4642
www.raymarine.com
Raymarine Inc.
21 Manchester Street,
Merrimack,
New Hampshire 03054-4801
USA
LEN
Raymarine plc
Anchorage Park,
Portsmouth,
Hampshire PO3 5TD
United Kingdom
Europe: R&TTE 1999/5/EC
USA: CFR47 Part 15
Canada: RSS-210
Approvals:
Base station to keyboard Typically 9 m (30 ft)
range
when Temperature: -20°C to 55°C (-4°F to 131°F)
relative humidity: 75%
operating temperature: -15°C to 55°C (5°F to 131°F)
non-operating temperature: -25°C to 70°C (-13°F to
158°F)
relative humidity limit: 95%
Environmental conditions:
conditions
1 mW
Transmitted power
Storage
packed:
9 V to 16 V
0.96 W
Power consumption
Surface mount
Mounting
Supply voltage
66 mm x 118 mm x 36mm
(2.6 in x 4.7 in x 1.4 in)
Size
Wireless base station technical specification
87086_1.book Page 8 Thursday, October 4, 2007 8:47 AM

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Trapped                         : False
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2007:10:04 08:52:50+01:00
Create Date                     : 2007:10:04 08:48:40+01:00
Metadata Date                   : 2007:10:04 08:52:50+01:00
Format                          : application/pdf
Title                           : 87086_1.book
Creator                         : asimpson
GTS PDFX Version                : PDF/X-1:2001
GTS PDFX Conformance            : PDF/X-1a:2001
Document ID                     : uuid:0403b403-c32b-4956-a69a-153df5e40ee4
Instance ID                     : uuid:caef2f97-f12b-4fde-9331-81c5bce2b5f2
Page Count                      : 8
Author                          : asimpson
EXIF Metadata provided by EXIF.tools
FCC ID Filing: PJ5-STNGB

Navigation menu