Food Automation Service Techniques XWIRE-REPEATER Food quality & supply chain monitor equipment User Manual Letter Size
Food Automation - Service Techniques, Inc. Food quality & supply chain monitor equipment Letter Size
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1590249 |
| Application ID | vvhI7qY6UwaADcTrkZRxDg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 39.99kB (499930 bits) |
| Date Submitted | 2011-11-29 00:00:00 |
| Date Available | 2012-05-26 00:00:00 |
| Creation Date | 2008-03-05 10:29:13 |
| Producing Software | QuarkXPress(R) 7.3 |
| Document Lastmod | 2008-03-05 10:29:13 |
| Document Title | Letter Size |
| Document Creator | QuarkXPress(R) 7.3 |
Direct, Inc. www.MySCK.com Installation Guide SmartRepeater Device TM "...because you can't improve what you don't measure" ( These instructions should be saved for future reference. ) SmartRepeater Direct, Inc. TM NOTICES BEFORE YOU INSTALL SCK Direct, Inc. is not liable for any use of product not in accordance with SCK Direct, Inc.’s installation and operation instructions. SmartRepeaters should be installed after the installation of your SCK Smart Direct 2TM, SCK Kitchen AdvisorTM, or (FAST.) XwireTM Wireless Gateway. CLEANING Using a clean damp cloth, wipe down the SmartRepeater when necessary using a commercial quality foodservice-approved detergent. DO NOT IMMERSE. Changes or modifications not expressly approved by SCK Direct, Inc. could void the user's authority to operate the equipment. NEVER use chemical or abrasive cleaners on the SmartRepeater. TOOLS REQUIRED FOR INSTALLATION Drill Bit: 3/16” if using wall anchor, or #50 if installing into Phillips Screwdrivers metal INCLUDED PARTS Please confirm that these parts have shipped with your order: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and SmartRepeater: 231-60233-01 Mounting Kit: 213-50641 Power Supply Mounting Kit: 213-50759-01 Strain Relief Kit: 213-50760-01 Connect the equipment into an outlet on a circuit different receiver. Consult the dealer for help. from that to which the receiver is connected. If something is missing, please call 1-866-840-4271 (8:00 a.m. 5:00 p.m. EST). POWER SUPPLY 126-10033 POWER CORD OPTIONS 126-10028: Power Cord U.S. 126-10029: Power Cord Euro, Round 126-10030: Power Cord UK, Flat This document contains confidential information. The dissemination, publication, copying, or duplication of this document or the software described herein without prior written authorization is strictly prohibited. © 2008 SCK Direct, Inc. 229-51379 Rev A www.MySCK.com installation guide STRAIN RELIEF SETUP MOUNTING INSTRUCTIONS 1. 1. Apply the supplied Ty-wrap adhesive-backed mount (15015028) on the bottom side of the SmartRepeater (1) one inch from the power supply plug. Choose a location for the SmartRepeater to be installed (within 8 feet of an outlet). Use the SmartRepeater mounting bracket template found in this guide to mark the locations of the 2 mounting holes. View the tentative positioning and ensure there are no location problems. Drill the 2 pilot holes. (If you are using the supplied wall anchors, use a 3/16 bit. For mounting into sheet metal, use a #50 bit.) Insert screws into the mounting bracket holes and tighten. 2. Clip the Smart Repeater into its bracket. 3. Plug the SmartRepeater into outlet. ALTERNATIVE MOUNTING OPTION USING SUPPLIED VELCRO 2. Run the supplied Ty-wrap (150-15005R) through one of the holes on the adhesive backed mount. 1. Choose a location to install the SmartRepeater (within 8 feet of an outlet). 2. Clean the mounting surface and back of the SmartRepeater with the supplied alcohol wipe. 3. Adhere one piece of the supplied Velcro to the surface where you want to mount the SmartRepeater. Make sure there will be no obstructions once the SmartRepeater is mounted. 3. Plug the power supply into the SmartRepeater. Take the power cord and Ty-wrap it so the power cord does not become unplugged when mounted on a surface. 4. Adhere the second piece of supplied Velcro to the back side of the SmartRepeater. Then adhere the SmartRepeater onto the mounting location. 5. Plug the SmartRepeater into outlet. This document contains confidential information. The dissemination, publication, copying, or duplication of this document or the software described herein without prior written authorization is strictly prohibited. © 2008 SCK Direct, Inc. 229-51379 Rev A www.MySCK.com SmartRepeater Direct, Inc. TM INDICATOR CHARTS Troubleshooting / LED Codes Signal Strength Indicator LED Action Description Strobe effect using all LEDs Device is scanning the channels for available networks. LEDs alternate being lit in sequence for a period of time. A diagnostic command was issued to this device to blink the LEDs in a recognizable pattern for a set amount of time. Signal LEDs Bars Link Quality NONE(0) No signal or No messages received ONE(1) Moderate signal TWO(2) Good signal THREE(3) Excellent signal Status LED Chart LED Color LED Blink Rate RED Solid On RED Slow Device is connected as a router Device is waiting for data from its parent node RED Very Fast Device is communicating with another device as a router. Signal bars should exist. GREEN Solid On Device is connected as a coordinator Very Fast Device is communicating with another device as a coordinator. Signal bars should exist. GREEN Description This document contains confidential information. The dissemination, publication, copying, or duplication of this document or the software described herein without prior written authorization is strictly prohibited. © 2008 SCK Direct, Inc. 229-51379 Rev A www.MySCK.com installation guide MOUNTING TEMPLATE Use this template as a guide to install your SmartRepeater mounting bracket. Drawing is to scale. 214-53639A This document contains confidential information. The dissemination, publication, copying, or duplication of this document or the software described herein without prior written authorization is strictly prohibited. © 2008 SCK Direct, Inc. 229-51379 Rev A www.MySCK.com SmartRepeater Direct, Inc. TM This page left intentionally blank. This document contains confidential information. The dissemination, publication, copying, or duplication of this document or the software described herein without prior written authorization is strictly prohibited. © 2008 SCK Direct, Inc. 229-51379 Rev A www.MySCK.com installation guide This page left intentionally blank. This document contains confidential information. The dissemination, publication, copying, or duplication of this document or the software described herein without prior written authorization is strictly prohibited. © 2008 SCK Direct, Inc. 229-51379 Rev A www.MySCK.com Troubleshooting Should you experience problems installing your SCK SmartRepeater, or any aspect of your SCK Direct, Inc. services, please contact the SCK HelpDesk toll-free at 1.866.840.4271 (Monday-Friday, 8:00 a.m.-5:00 p.m. EST). Optional SCK System Components SCK has a variety of optional accessories to help you complete your kitchen automation: SCK Kitchen Advisor Information Server SCK Remote Input Device SCK KMS Kitchen Status Monitor SCK-Enabled Appliance Controllers SCK Wireless (XwireTM) Appliance Interface SCK Wireless (XwireTM) Temperature/Door SmartSensorTM SCK Wireless (XwireTM) Wireless.Gateway SCK Wired Backbone For additional information on any of these accessories, or to request Technical Specification Sheets, please contact your SCK Representative or contact SCK Customer Support toll-free at 1-866-840-4271 (Monday-Friday, 8:00 a.m. to 5:00 p.m. EST). Thank You for Choosing SCK Direct, Inc! SCK Direct, Inc. 905 Honeyspot Road Stratford, CT 06615 +1 203.377.4174 voice +1 203.377.8187 fax 1.866.840.4271 toll-free sales & helpdesk www.MySCK.com; info@mysck.com 229-51379 Rev. A © 2008 SCK Direct, Inc. Printed in the USA 05MAR2008 Direct, Inc. This document contains confidential information. The dissemination, publication, copying, or duplication of this document or the software described herein without prior written authorization is strictly prohibited.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 8 X Press Private : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%EndComments Creator : QuarkXPress(R) 7.3 Modify Date : 2008:03:05 10:29:13 Create Date : 2008:03:05 10:29:13 Producer : QuarkXPress(R) 7.3 Title : Letter SizeEXIF Metadata provided by EXIF.tools