Fuji Film 01000005 Flat Panel Sensor User Manual DR ID900PU Manual 2nd Ed f
Fuji Film Corporation Flat Panel Sensor DR ID900PU Manual 2nd Ed f
(Short term Confidential)User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2206425 |
| Application ID | 0oxuOQ/vvrRaLVp19N4h2A== |
| Document Description | (Short term Confidential)User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 75.01kB (937590 bits) |
| Date Submitted | 2014-03-05 00:00:00 |
| Date Available | 2014-09-01 00:00:00 |
| Creation Date | 2014-02-27 14:10:00 |
| Producing Software | Acrobat Distiller 10.1.2 (Windows) |
| Document Lastmod | 2014-02-27 14:10:00 |
| Document Title | DR-ID900PU Manual (2nd Ed.)f.pdf |
| Document Creator | Adobe InDesign CS3_J (5.0.4) |
| Document Author: | 14539 |
For Safe Operation DR-ID 900PU Operation Manual 2nd Edition : July 2013 System Configuration (Product Overview) Basic Operation Daily Inspection and Maintenance Appendix Maintenance and Inspection This Operation Manual describes details on how to operate the DR-ID 900PU and cautions to be observed when operating it. Please read the Operation Manual thoroughly before actually operating the DR-ID 900PU along with “DR-ID 300CL Reference Guide” and other manuals for the related products. After reading this manual, store it nearby the DR-ID 900PU so that you can see it whenever necessary. 897N102280A ii DR-ID 900PU Operation Manual 897N102280A Introduction DR-ID 900PU is an X-ray equipment which acquires a general radiograph from the indirectconversion flat panel sensor. DR-ID 900PU consists of DR-ID 900MP and DR-ID 911SE/DR-ID 601SE/DR-ID 602SE/DR-ID 611SE/ DR-ID 613SE. DR-ID 911SE, DR-ID 601SE, DR-ID 602SE, DR-ID 611SE and DR-ID 613SE :Wireless communication mode or wired communication mode is available. When used in wireless communication mode, an access point*1, battery pack (optional) and battery charger (optional) are required. *1 In the countries other than the U.S., an access point is not included as a component of the system. For details including installation, consult our official dealer. Each flat panel sensor complies with IEC 62220-1 (MEDICAL ELECTRICAL EQUIPMENT CHARACTERISTICS OF DIGITAL X-RAY IMAGING DEVICES - ) as a general X-ray radiography equipment. The detector of flat panel sensors features 150 micron pixel pitch, a wide 16-bit dynamic range and exposure times up to 3.8 seconds. This Operation Manual includes descriptions of matters necessary when using the DR-ID 900PU such as the equipment overview, operation procedures and precautions to observe, as well as daily inspections and maintenance. Accompanying documents were originally drafted in the English language. Installation may only be conducted by authorized service personal. CAUTIONS 1. No part or all of this manual may be reproduced in any form without prior permission. 2. The information contained in this manual may be subject to change without prior notice. 3. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from installation, relocation, remodeling, maintenance, and repair performed by other than dealers specified by FUJIFILM Corporation. 4. FUJIFILM Corporation shall not be liable for malfunctions and damages of FUJIFILM Corporation products due to products of other manufacturers not supplied by FUJIFILM Corporation. 5. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from remodeling, maintenance, and repair using repair parts other than those specified by FUJIFILM Corporation. 6. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from negligence of precautions and operating methods contained in this manual. 7. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from use under environment conditions outside the range of using conditions for this product such as power supply, installation environment, etc. contained in this manual. 8. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from natural disasters such as fires, earthquakes, floods, lightning, etc. This system is classified as a medical device under EC Directive 93/42/EEC. Process waste correctly, as stipulated by local law or any regulations that apply. Caution : Rx Only in the United States (Federal law restricts this device to sale by or on the order of a physician.) Open-Source Software Used in This Product This product uses third party’s software that is made available as open source software or free software. For information on open source software used in this product, please see the attached CD. Source codes for certain type of open source software used in this product are available at delivery cost. If you would like to receive such source codes, please contact FUJIFILM dealer or the service representatives at the agency from which you purchased this product. (Please be noted that any inquiries concerning the contents of source codes should be directed to original licensers of open source software.) Note : FUJIFILM has successfully performed verification and validation testing on all third party software and has confirmed its suitability to be used in this system. Trademarks All company names and product names described in this manual are the trademarks or registered trademarks of FUJIFILM Corporation or their respective holders. Windows is the registered trademark of US Microsoft Corporation in the U.S.A. and other countries. Copyright © 2013 FUJIFILM Corporation. All rights reserved. DR-ID 900PU Operation Manual 897N102280A iii Contents Introduction ...........................................................................................................................iii Chapter 1 For Safe Operation 1.1 1.2 Safety ...................................................................................................................... 1-1 Electromagnetic Compatibility (EMC)...................................................................... 1-9 1.2.1 DR-ID 900PU ...........................................................................................................1-9 Chapter 2 System Configuration (Product Overview) 2.1 DR-ID 900PU .......................................................................................................... 2-1 2.1.1 2.2 2.3 System Configuration ..............................................................................................2-1 Unit Names and the Functions ................................................................................ 2-2 Locations of Labels and Signs ................................................................................ 2-3 2.3.1 2.3.2 Locations of Labels ..................................................................................................2-3 Safety and Other Symbols .......................................................................................2-6 Chapter 3 Basic Operation 3.1 Preparing the Flat Panel Sensor ............................................................................. 3-1 3.1.1 3.1.2 3.1.3 3.1.4 3.1.5 3.1.6 3.1.7 3.2 Type of Flat Panel Sensor .......................................................................................3-1 Number of the Connectable Flat Panel Sensors .....................................................3-1 Connecting/Disconnecting the Flat Panel Sensor Connector ..................................3-2 Inserting/Removing the Flat Panel Sensor into/ from the Radiographic Examination Stand ..............................................................3-3 [1] In the case of the flat panel sensor DR-ID 911SE ..............................................3-3 [2] In the case of the flat panel sensors DR-ID 601SE/DR-ID 602SE/ DR-ID 611SE/DR-ID 613SE ...............................................................................3-3 Changing the Direction of the Flat Panel Sensor Connector ...................................3-5 Charging the Battery Pack (optional) for the Flat Panel Sensor ..............................3-5 Installing/Removing the Battery Pack (optional) for the Flat Panel Sensor .............3-6 Starting Up and Shutting Down the DR-ID 900PU .................................................. 3-7 3.2.1 3.2.2 Starting Up the DR-ID 900PU ..................................................................................3-7 Shutting Down the DR-ID 900PU ............................................................................3-7 Chapter 4 Daily Inspection and Maintenance 4.1 Daily User Inspection and Maintenance .................................................................. 4-1 4.1.1 Periodical Inspection................................................................................................4-1 Appendix A Specifications A.1 Specifications ..........................................................................................................A-1 A.1.1 A.1.2 A.1.3 A.1.4 Reduced Equivalent (DR-ID 900) ........................................................................... A-1 Power Supply Conditions........................................................................................ A-1 Environmental Conditions ....................................................................................... A-1 Image performance................................................................................................. A-1 Appendix O Use of Optional Items O.1 Optional Items ....................................................................................................... O-1 O.2 Using the Retaining Bracket for MP ....................................................................... O-2 Maintenance and Inspection iv DR-ID 900PU Operation Manual 897N102280A Chapter 1 For Safe Operation 1.1 Safety Before using the DR-ID 900PU, read this section thoroughly to ensure that you use the product properly. For Safe Operation Electric Shock Warnings and Cautions WARNING The power supply to the DR-ID 900PU is AC100 to 240V. To avoid electric shocks, users should always take the following precautions: ● Never open any covers of the equipment. ● Install the equipment in a location where it will not be exposed to water. ● Check that the equipment is securely earthed. ● Check that all of the cords and cables are completely and securely connected. ● Keep the image processing unit and the control cabinet out of reach of patients. WARNING Do not touch the patient’s body while touching the control cabinet. Otherwise, the patient may receive an electric shock. WARNING Do not use a multiple tap connector or extension cable for powering the devices constituting the system. Otherwise, fire or electric shock may occur due to the electrical load exceeding the allowable limit. WARNING Observe the following precautions when using the cables. ● Turn off each unit before connecting/disconnecting the cable. Do not touch the plug and connector with wet hands. Otherwise, electric shock may result, causing death or severe injury. ● Hold the plug or connector when removing the cable. Pulling the cable or carrying by holding it may damage the cable, causing fire or electric shock. ● Do not damage or remodel the cable. Do not place a heavy object on the cable or lay it under the flat panel sensor. Do not step on, pull, forcibly bend, or bundle the cable. Otherwise, fire or electric shock may result. ● Do not use the flat panel sensor for the radiographic examination stand if its cable becomes overloaded. Otherwise, the cable may be damaged, causing fire or electric shock. WARNING Do not turn on the system with dew condensation on the flat panel sensor. Otherwise, fire or electric shock may result. WARNING Do not use the equipment in a location where metal particles could come into the equipment. This may cause an electric shock. DR-ID 900PU Operation Manual 897N102280A 1-1 WARNING Do not disassemble or remodel the equipment. Otherwise, fire or electric shock may result. Keep away from the parts inside the product, which may cause electric shock. If you touch them accidentally, death or severe injury may result. WARNING Do not hit or drop the equipment or subject it to severe shock. Otherwise, the equipment may be damaged. If the damaged equipment is used, fire or electric shock may result. For Safe Operation WARNING Do not use the flat panel sensor when the battery cover and the battery pack are not installed. Doing so may cause electric shock WARNING Make sure to use the optional parts and accessories recommended by us. Failure to use the optional parts and accessories recommended by us may result in electric shock or injury. CAUTIONS As the cables of the equipment are long, be careful not to entangle the cables during use. Also, be careful not to trip over the cables. Falls could result in injury. CAUTIONS Be sure to follow the specified procedure when turning off the power of the equipment. Otherwise, the flat panel sensor could be damaged. CAUTIONS Do not store magnetic media near the DR system and control cabinet. Otherwise, magnetism generated by the equipment may cause the data to be lost. CAUTIONS Keep the equipment away from patient’s body fluids, chemicals, water, etc. Otherwise, it may become damaged, causing fire or electric shock. If necessary, protect the flat panel sensor by covering it with a disposable bag. Explosion Warnings WARNING Because this equipment is not explosion-proof, do not use combustible and explosive gases near the equipment. WARNING Flammable gasses may stay in the room after disinfection. Ventilate the room well before powering on the equipment following disinfection. 1-2 DR-ID 900PU Operation Manual 897N102280A Warnings for Abnormalities WARNING If any of the following occurs, immediately turn off the power of each unit, unplug the power cable from the outlet, and then contact a FUJIFILM dealer. ● When smoke, strange odor, or abnormal sound is present. ● When a foreign object (such as a metal object) or liquid enters the product. ● When the equipment is dropped or hit and is damaged. For Safe Operation Installation Precautions CAUTIONS Do not install the equipment in a location with the following conditions. ● Where the temperature changes sharply. ● Close to heat sources such as a heater. ● Where the equipment may be exposed to water due to water leakage or ingress. ● Where corrosive gas may be generated. ● Where there is excessive dust. ● Where the equipment is subject to frequent or excessive vibration/shock. ● Where the equipment is exposed to direct sunlight. CAUTIONS For veterinary or mobile applications, please contact a certified FUJIFILM service representative. CAUTIONS Use the system indoor in wireless communication mode. For details, contact a FUJIFILM dealer. CAUTIONS Do not place any object in a place where removal of the power cable is prevented. Connection Instructions WARNING Make sure that the devices to be connected to the equipment are authorized for connection. WARNING Connect the DR-ID 900PU only to the designated control cabinet (DR-ID 900MC). When the DR-ID 900PU is connected to X-ray equipment, make sure that the equipment complies with IEC 60601-1. Warning regarding radiographic examination stands WARNING In the case of using this product in combination with an upright-type or bed-type radiographic examination stand, select an upright-type or bed-type radiographic examination stand whose aluminum equivalent, of the front panel of the upright-type radiographic examination and the top of the bed-type radiographic examination or the like, complies with IEC 60601-1-3: 2008/EN 60601-1-3: 2008. DR-ID 900PU Operation Manual 897N102280A 1-3 Precautions on External Network Connection CAUTIONS When a setting of the network to which the equipment is connected has been changed, check that the change does not affect the system operation and take measures if necessary. The setting change may include the following: ● Change of connection destination ● Addition of devices ● Removal of devices ● Update of devices ● Upgrade of devices For Safe Operation Software Precautions CAUTIONS Connect to the Ethernet Network of 1000BASE-T, 100BASE-TX, or 10BASE-T prescribed in the IEEE standard 802.3. Do not connect telephone lines to LAN connector. Only UTP-type straight LAN cables of 4-pair Category 5 cable (CAT 5E) or higher are appropriate for connection to this connector. CAUTIONS After connecting this system to the network with other systems,confirm that the other systems are not affected. If they are affected, take countermeasures such as network separation. System Isolation Instructions WARNING To ensure complete system isolation, never install any unauthorized accessories or other such items. When it is necessary to install authorized accessories or optional items, contact a FUJIFILM dealer. WARNING Keep equipment other than those used for patients out of their reach to ensure appropriate system isolation. WARNING Do not move the Console from where it is installed. WARNING In normal use, have a patient take a proper positioning for exposure. The operator should operate the system in a place where safety from radiation is ensured. The operator should also make sure before exposure that no one but the patient is in the exposure area and the operating area of the system. 1-4 DR-ID 900PU Operation Manual 897N102280A Software Precautions CAUTIONS Do not install additional software to the system. Do not uninstall any of the software preinstalled in the system. The system is preinstalled with the appropriate software. If other software is installed or if the existing software is uninstalled, various operational errors may result. Various operational errors may result. For Safe Operation Disinfection Instructions WARNING Confirm that the respiratory density of disinfectant including solvent is under legal regulation. Certain disinfectants may damage health. When using a disinfectant, follow instructions supplied by the manufacturers. WARNING Ethanol for disinfection is recommended as the disinfectant. Carefully read the instructions and cautions supplied with the disinfectant before use. Do not use the following when disinfecting. Otherwise, the equipment may be damaged, and its quality, performance, and safety cannot be guaranteed. ● Chloric disinfectant which is strongly corrosive to metals and rubber. parts. ● Disinfectant whose use on metals, plastics, and coating is forbidden according to the instructions supplied with the disinfectant. ● Formalin gas and disinfectant sprays that may get inside the equipment. ● Ultraviolet sterilizers CAUTIONS Clean the sensor unit of the flat panel sensor with ethanol for disinfection, etc. for each patient to prevent infection. Precautions for Charging the Battery CAUTIONS ● Use the battery charger recommended by FUJIFILM Corporation. For details on operations, refer to the instruction manual for the battery charger. ● Do not charge the battery pack near fire or under strong sunshine. If the built-in protection mechanisms are activated by a high temperature, the battery pack cannot be charged. Also, if the built-in protection mechanisms are damaged, the battery pack may be charged with extremely high current and voltage, and abnormal chemical reactions may occur inside the battery pack, causing it to overheat, emit smoke, explode or ignite. ● Immediately stop charging the battery pack, if charging is not completed within the specified time. Otherwise, the battery pack may overheat, emit smoke, explode or ignite. ● Do not use the flat panel sensor near the AC adapter. ● Do not use the broken battery charger. Battery Pack (Optional) Precautions WARNING If this equipment is not in use for while, store it with the battery pack removed. Not removing the battery pack may cause malfunction. DR-ID 900PU Operation Manual 897N102280A 1-5 CAUTIONS Be sure to observe the following cautions when using the battery pack (optional). ● Do not use the battery pack with any device other than those designated by FUJIFILM Corporation. ● Charge the battery pack only with the designated battery charger. If the battery pack is charged under the charging conditions (voltage, current and charging method) different from those specified by FUJIFILM Corporation, the battery pack may emit smoke, ignite, explode or leak fluid. ● When storing the battery pack (125N100050) for a long period, charge the battery fully, remove it from the flat panel sensor and then store it in a cool and dark place. Recharge the stored battery every six months or every year. Otherwise a decrease in battery capacity or other problems may result. ● Do not leave the removed battery pack in a car or other place exposed to high temperature. ● Use and store the battery pack only in the environmental conditions specified by FUJIFILM Corporation. If the battery pack is used or stored in a place where it is exposed to high temperature, the battery pack may emit smoke, ignite, explode or leak fluid. ● When disposing of the battery pack, consult our official dealer. ● Do not disassemble or remodel the battery pack. The battery pack is equipped with built-in safety and protection mechanisms. If they are damaged, the battery pack may overheat, emit smoke, explode or ignite. ● Do not connect the positive (+) and negative (-) terminals of the battery pack using any metal object, such as a wire. Do not carry or store the battery pack together with metal objects such as necklaces or hairpins. Otherwise, the battery pack may short-circuit and overcurrent may flow, causing the battery pack to overheat, emit smoke, explode or ignite. Metal objects such as necklaces or hairpins may also become hot. ● Do not throw the battery pack into fire or expose it to excessive heat. Otherwise, its insulator may melt, its gas release vent or safety mechanisms may be damaged, and/or its electrolyte may catch fire, causing the battery pack to overheat, emit smoke, explode or ignite. ● Do not use or leave the battery pack in a place where it is exposed to high temperature (80°C or higher), such as fire or a heater. If the resin separator is damaged due to heat, the battery pack may short-circuit, causing it to overheat, emit smoke, explode or ignite. ● Do not immerse the battery pack in water or seawater, and do not allow it to become wet. If the built-in protection mechanisms are damaged, the battery pack may overheat, emit smoke, explode or ignite. ● Do not pierce the battery pack with a nail, hit it with a hammer, or step on it. Otherwise, the battery pack may be damaged or deformed and short-circuit, causing it to overheat, emit smoke, explode or ignite. ● Do not subject the battery pack to strong impact or throw it. If the built-in protection mechanisms are damaged, the battery pack may be charged with extremely high current and voltage, and abnormal chemical reactions may occur inside the battery pack, causing it to overheat, emit smoke, explode or ignite. ● Do not use an apparently damaged or deformed battery pack. Otherwise, the battery pack may overheat, emit smoke, explode or ignite. ● Do not solder the battery pack directly. Otherwise, its insulator may melt, or its gas release vent or safety mechanisms may be damaged, causing the battery pack to overheat, emit smoke, explode or ignite. ● Do not reverse the positive (+) and negative (-) terminals of the battery pack. Otherwise, the battery pack may be reverse-charged during charging. As a result, abnormal chemical reactions may occur inside the battery pack, or extremely high current may flow during discharging, causing it to overheat, emit smoke, explode or ignite. ● The battery pack has a predetermined polarity. If you cannot connect the battery pack to the battery charger or other equipment, do not connect the battery pack forcefully. Make sure that the terminals are correctly oriented. If the battery pack is connected in reverse, it will be reverse-charged, and abnormal chemical reactions may occur inside the battery pack, causing it to overheat, emit smoke, explode or ignite. ● Do not connect the battery pack to an electrical outlet or cigarette lighter socket in a car. Overcurrent may flow to the battery pack due to high voltage applied, causing the battery pack to overheat, emit smoke, explode or ignite. ● Do not use the battery pack for equipment other than those specified. Otherwise, the guaranteed performance will be reduced and/or the service life will be shortened. Depending on the equipment to which the battery pack is connected, extremely high current may flow, For Safe Operation 1-6 DR-ID 900PU Operation Manual 897N102280A causing the battery pack to be damaged, overheat, emit smoke, explode or ignite. ● If the electrolyte leaked from the battery pack enters the eyes, do not rub them. Wash the eyes immediately with clean water such as tap water, and consult a doctor. Otherwise, eye injury may result. ● Do not use the battery pack in combination with a primary battery such as a dry battery or other battery of a different capacity, type and/or brand. Otherwise, the battery pack may be overcharged during charging, and abnormal chemical reactions may occur inside the battery pack, causing it to overheat, emit smoke, explode or ignite. ● Do not put the battery pack in a microwave oven or high-pressure container. Otherwise, the battery pack may be rapidly heated or damaged, causing it to overheat, emit smoke, explode or ignite. ● If the battery pack leaks or emits an unusual odor, remove it from fire immediately. Otherwise, the leaked electrolyte may catch fire, causing the battery pack to overheat, emit smoke, explode or ignite. ● If you notice an unusual odor, heat, discoloration, deformation or any other abnormality during use, charging or storage, remove the battery pack from the equipment or battery charger, and stop using it. Otherwise, the battery pack may overheat, emit smoke, explode or ignite. ● Do not use the battery pack exposed to a strong magnetic field of an MRI system, etc. ● Do not use the battery pack immersed in liquid. For Safe Operation Other Warnings and Cautions WARNING No modification of this equipment is allowed. CAUTIONS Install the system in accordance with what is provided by IEC60601-1-1. Contact a FUJIFILM dealer for installation and relocation (except the flat panel sensor) of the system. CAUTIONS Do not hit or drop the equipment. Otherwise, injury or damage to images, etc. may result. CAUTIONS Be sure to inspect the system periodically. To assure optimum performance of the equipment, it is necessary to systematically perform maintenance and inspection. For information on maintenance and inspection, contact a FUJIFILM dealer. CAUTIONS The institution where the equipment is installed is responsible for its use and maintenance. In addition, this equipment should not be used by persons other than doctors or suitably trained staff. CAUTIONS Do not place the cable terminal on the floor.Doing so may cause infection. Also, periodically clean the cable and the terminal. CAUTIONS The institution where the equipment is installed is responsible for its use and maintenance. In addition, this equipment should not be used by persons other than doctors or suitably trained staff. DR-ID 900PU Operation Manual 897N102280A 1-7 Contraindications and Prohibitions No contraindications present. Classification ● According to the type of protection against electrical shock Wired communication mode: Class 1 equipment (stationary) Wireless communication mode: Internal power supply For Safe Operation ● According to the degree of protection against electrical shock Type B applied part ● According to the degree of protection against harmful ingress of water IPX0 ● According to the degree of safety of application in the presence of a flammable anesthetics mixture with air or with oxygen or nitrous oxide. Equipment not suitable for use in the presence of a flammable anesthetics mixture with air or with oxygen or nitrous oxide. ● According to the mode of operation CONTINUOUS OPERATION 1-8 DR-ID 900PU Operation Manual 897N102280A 1.2 Electromagnetic Compatibility (EMC) 1.2.1 DR-ID 900PU DR-ID 900PU consists of DR-ID 900MP and DR-ID 911SE/DR-ID 601SE/DR-ID 602SE/DR-ID 611SE/ DR-ID 613SE. For Safe Operation This equipment has been tested and found to comply with the limits for medical devices to the IEC 60601-1-2:2001+A1:2004/EN 60601-1-2:2001+A1:2006, IEC 60601-1-2:2007/EN 60601-1-2:2007, Medical Device Directive 93/42/EEC. These limits are designed to provide reasonable protection against harmful interference in a typical medical installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to other devices in the vicinity. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to other devices, which can be determined by tuning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving device. • Increase the separation between the equipment. • Connect the equipment into an outlet on a circuit different from that to which the other device(s) are connected. If the problem cannot be solved with the above measures, stop using this equipment and consult the manufacturer or our official dealer for help. WARNING ● Do not place devices generating electromagnetic wave near this equipment. ● If a device(s) other than those specified is connected, predetermined EMC performance cannot be guaranteed. Further information for IEC 60601-1-2 (EN60601-1-2) 1. Medical electrical equipment needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided in the accompanying documents. 2. Portable and mobile RF communications equipment can affect medical electrical equipment. 3. Information regarding the cable affecting EMC is as follows. Name Maximum Length General Specification Network Cable 30m (98.4 ft.) Cat5e or more, UTP type and straight cable Power Cable 3m (9.8 ft.) Use a hospital grade power cable. (for North America) A non-hospital grade power cable can be used. (for other countries) 4. The use of accessories, transducers and cables other than those specified, with the exception of transducers and cables sold by FUJIFILM Corporation as replacement parts for internal components, may result in increased emissions or decreased immunity of the DR-ID 900PU. 5. The DR-ID 900PU should not be used adjacent to or stacked with other equipment. If adjacent or stacked use is necessary, the DR-ID 900PU should be observed to verify normal operation in the configuration in which it will be used. 6. Basic performance of the equipment and the system After image data are acquired from the panel unit (DR-ID 900PU), data correction is performed by the control unit (DR-ID 900MC), and the image is saved in and displayed on the image processing unit. 7. Test items (Tables 1 to 4) DR-ID 900PU Operation Manual 897N102280A 1-9 Table 1 Guidance and manufacturer’s declaration - electromagnetic emissions The DR-ID 900PU is intended for use in the electromagnetic environment specified below. The customer or the user of the DR-ID 900PU should assure that they are used in such an environment. Emissions test Compliance For Safe Operation RF emissions CISPR 11 Group 1 RF emissions CISPR 11 Class A Harmonic emissions IEC61000-3-2 Complies Voltage fluctuations/ flicker emissions IEC61000-3-3 Complies Electromagnetic environment - guidance The DR-ID 900PU uses RF energy only for their internal function. Therefore, their RF emissions are very low and are not likely to cause any interference in nearby electronic equipment. Class A The DR-ID 900PU is suitable for use in all establishments other than domestic and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes. Table 2 Guidance and manufacturer’s declaration - electromagnetic immunity The DR-ID 900PU is intended for use in the electromagnetic environment specified below. The customer or the user of the DR-ID 900PU should assure that they are used in such an environment. Immunity test IEC 60601 test level Compliance level Electrostatic discharge (ESD) IEC61000-4-2 ±6kV contact ±8kV air ±6kV contact ±8kV air Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30%. Electrical fast transient/burst IEC61000-4-4 ±2kV for power supply lines ±1kV for input/output lines ±2kV for power supply lines ±1kV for input/output lines Mains power quality should be that of a typical commercial or hospital environment. Surge IEC61000-4-5 ±1kV differential mode ±2kV common mode ±1kV differential mode ±2kV common mode Mains power quality should be that of a typical commercial or hospital environment. Voltage dips, short interruptions and voltage variations on power supply input lines IEC61000-4-11 <5% UT (>95% dip in UT) for 0.5 cycle 40% UT (60% dip in UT) for 5 cycles 70% UT (30% dip in UT) for 25 cycles <5% UT (>95% dip in UT) for 5 s <5% UT (>95% dip in UT) for 0.5 cycle 40% UT (60% dip in UT) for 5 cycles 70% UT (30% dip in UT) for 25 cycles <5% UT (>95% dip in UT) for 5 s Mains power quality should be that of a typical commercial or hospital environment. If the user of the DR-ID 900PU requires continued operation during power mains interruptions, it is recommended that the DR-ID 900PU be powered from an uninterruptible power supply or a battery. 3 A/m Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment. Power frequency (50/60Hz) magnetic field IEC61000-4-8 3 A/m NOTE: UT is the a.c. mains voltage prior to application of the test level. 1-10 Electromagnetic environment guidance DR-ID 900PU Operation Manual 897N102280A Table 3 Guidance and manufacturer’s declaration - electromagnetic immunity The DR-ID 900PU is intended for use in the electromagnetic environment specified below. The customer or the user of the DR-ID 900PU should assure that they are used in such an environment. Immunity test IEC 60601 test level Compliance level 3 Vrms 150 kHz to 80 MHz 3 Vrms Radiated RF IEC61000-4-3 3 V/m 80 MHz to 2.5 GHz 3 V/m Portable and mobile RF communications equipment should be used no closer to any part of the DR-ID 900PU, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter. For Safe Operation Conducted RF IEC61000-4-6 Electromagnetic environment - guidance Recommended separation distance d = 1.2 d = 1.2 80 MHz to 800 MHz d = 2.3 800 MHz to 2.5 GHz where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in metres (m). Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey,a should be less than the compliance level in each frequency range.b Interference may occur in the vicinity of equipment marked with the following symbol: NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. a Field strength from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the DR-ID 900PU is used exceeds the applicable RF compliance, the DR-ID 900PU should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the DR-ID 900PU. b Over the frequency range 150 kHz to 80 MHz, field strength should be less than 3 V/m. DR-ID 900PU Operation Manual 897N102280A 1-11 Table 4 Recommended separation distances between Portable and mobile RF communications equipment and the DR-ID 900PU The DR-ID 900PU is intended for use in the electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the DR-ID 900PU can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the DR-ID 900PU as recommended below, according to the maximum output power of the communications equipment. For Safe Operation Rated maximum output power of transmitter 0.01 0.1 10 100 Separation distance according to frequency of transmitter 150 kHz to 80 MHz d = 1.2 0.12 0.38 1.2 3.8 12 80 MHz to 800 MHz d = 1.2 0.12 0.38 1.2 3.8 12 800 MHz to 2.5 GHz d = 2.3 0.23 0.73 2.3 7.3 23 For transmitters rated at a maximum output power not listed above, the recommended separation distance d in metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer. NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies. NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. 1-12 DR-ID 900PU Operation Manual 897N102280A Chapter 2 System Configuration (Product Overview) 2.1 DR-ID 900PU 2.1.1 System Configuration For the U.S. DR-ID 900 DR-ID 900 DR-ID 900PU DR-ID 900PU Flat panel sensor Flat panel sensor Flat panel sensor Power supply unit DR-ID 900MP Control cabinet DR-ID 900MC Battery charger Access point Flat panel sensor System Configuration (Product Overview) Flat panel sensor For other countries Flat panel sensor Power supply unit DR-ID 900MP Image processing unit DR-ID 900CL Control cabinet DR-ID 900MC Ethernet switch (Hub) Image processing unit of other digital radiography system DR-ID 300CL Battery charger Image processing unit DR-ID 900CL Ethernet switch (Hub) Access point Image processing unit of other digital radiography system DR-ID 300CL • The products in can be installed in patient environment. • The FDR D-EVO Advanced consists of the DR-ID 900RU and the image processing unit. • An access point is used only in wireless communication mode. * The configuration of the system varies depending on the country. • One to four flat panel sensors can be connected to one power supply unit. If you connect all four flat panel sensors in wired communication mode or use them with three different techniques, two power supply units are required. • The flat panel sensor can be used in wireless communication mode or wired communication mode. • Up to four flat panel sensors can be connected in wired or wireless communication mode in DR-ID 900PU. However, either of the following conditions must be met: a) Two DR-ID 911SE flat panel sensors are connected in wired communication mode. (More than three flat panel sensors cannot be connected in wired communication mode.) b) Any two of the DR-ID 601SE, DR-ID 602SE, DR-ID 611SE and DR-ID 613SE flat panel sensors are connected in wired communication mode. DR-ID 900PU Operation Manual 897N102280A 2-1 2.2 Unit Names and the Functions Unit names and the functions of the DR-ID 900PU are described below. Applied part * Exposure plane is shown in this figure. Connector Applied part Connector Handle Flat panel sensor (DR-ID 911SE) Flat panel sensor (DR-ID 613SE) READY POWER ERROR System Configuration (Product Overview) Applied part Power status LED Status lamp Main switch Connector Flat panel sensor (DR-ID 601SE, DR-ID 602SE and DR-ID 611SE) Power supply unit (DR-ID 900MP) Name Flat panel sensor DR-ID 911SE, DRID 601SE, DR-ID 602SE, DR-ID 611SE and DR-ID 613SE Status lamp Description They incorporate a GOS indirect panel. However, the DR-ID 611SE and DR-ID 613SE incorporates a CsI indirect panel. Wireless communication mode or wired communication mode can be used. Indicates the equipment status by LEDs. READY (Green) On Exposure possible Blinks for 1.0 During exposure sequence second. Off Ready Wireless POWER (Green) (In wireless communication mode, the status of the battery pack is indicated. In wired communication mode, the power status is indicated.) ERROR (Orange) On OK (Power ON) Blinks for 1.0 Less than 10 min. second. Off Empty (Power OFF) Wired Power ON Power OFF On Communication not possible. Blinks for 1.0 Error occurred second. Off Normal * All LEDs are off when the equipment is off. Power supply unit (DR-ID 900MP) 2-2 Supplies the power to the flat panel sensor and connects the flat panel sensor and the control cabinet. Main switch Supplies the power to the flat panel sensor and the inside of the power supply unit. Power status LED Displays ON/OFF of the power supply unit. DR-ID 900PU Operation Manual 897N102280A 2.3 Locations of Labels and Signs Locations of labels and signs affixed to the DR-ID 900RU, and the relevant safety signs are shown below. 2.3.1 Locations of Labels Flat panel sensor (DR-ID 911SE) Flat panel sensor (DR-ID 601SE) Color Label Battery Cover Label Color Label DR-ID 601SE Caution Label Flat panel sensor (DR-ID 602SE) DR-ID 601SE Identification Label DR-ID 601SE Radio Law Certification Label Battery Cover Label System Configuration (Product Overview)DR-ID 911SE Identification Label/ DR-ID 911SE CE Mark Label/ DR-ID 911SE Caution Label DR-ID 911SE Radio Law Certification Label DR-ID 601SE CE Mark Label DR-ID 911SE Caution Label 1 DR-ID 911SE Caution Label 2 Flat panel sensor (DR-ID 611SE) Color Label Color Label DR-ID 602SE Caution Label DR-ID 611SE Caution Label DR-ID 602SE CE Mark Label DR-ID 611SE CE Mark Label DR-ID 602SE Identification Label DR-ID 602SE Radio Law Certification Label Battery Cover Label DR-ID 611SE Identification Label DR-ID 611SE Radio Law Certification Label Battery Cover Label Flat panel sensor (DR-ID 613SE) DR-ID 613SE Identification Label DR-ID 613SE Radio Law Certification Label Battery Cover Label DR-ID 613SE Caution Label 1 DR-ID 613SE Caution Label 2 Sample year of manufacture DR-ID 911SE Identification Label/DR-ID 911SE CE Mark Label/DR-ID 911SE Caution Label DR-ID 900PU Operation Manual 897N102280A 2-3 DR-ID 601SE Identification Label DR-ID 601SE CE Mark Label Sample year of manufacture DR-ID 602SE Identification Label DR-ID 602SE CE Mark Label Sample year of manufacture System Configuration (Product Overview) DR-ID 611SE Identification Label DR-ID 611SE CE Mark Label Sample year of manufacture Sample year of manufacture DR-ID 613SE Identification Label 150 Kg 330 lb DR-ID 601SE/DR-ID 602SE/DR-ID 611SE Caution Label W2Z-01000005 7736B-01000005 DR-ID 601SE/DR-ID 602SE/DR-ID 611SE Radio Law Certification Label DR-ID 911SE Radio Law Certification Label DR-ID 613SE Radio Law Certification Label Battery Cover Label 2-4 DR-ID 900PU Operation Manual 897N102280A Power supply unit (DR-ID 900MP) DR-ID 900MP Caution Label 1 DR-ID 900MP Caution Label 2 DR-ID 900MP Caution Label 3 DR-ID 900PU Rating Label For the types of connectable cables, consult a FUJIFILM dealer. System Configuration (Product Overview) Battery pack (optional) Battery pack Rating Label DR-ID 900MP Caution Label 1 DR-ID 900MP Caution Label 2 / DR-ID 911SE Caution Label 1 / DR-ID 613SE Caution Label 1 DR-ID 900PU Rating Label DR-ID 900MP Caution Label 3 / DR-ID 911SE Caution Label 2 / DR-ID 613SE Caution Label 2 Battery Pack Rating Label DR-ID 900PU Operation Manual 897N102280A 2-5 2.3.2 Safety and Other Symbols The following safety symbols are used in the labels or on its body. Symbol Description This symbol indicates compliance of the equipment with Directive 93/42/EEC. Caution (See “2.3.1 Locations of Labels” (page 2-3).) OFF (To indicate disconnection from the mains, at least for mains switches or their positions, and all those cases where safety is involved.) ON (To indicate connection to the mains, at least for mains switches or their positions, and all those cases where safety is involved.) Protective earth (ground) Alternating current System Configuration (Product Overview) This symbol indicates that the equipment is a Type B Applied Part. Ready (To indicate the machine is ready for operation.) Electric energy General mandatory action sign Stand-by This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2002/96/EC) and your national law. This product should be handed over to a designated collection point. Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about waste, please contact FUJIFILM dealers. Year of manufacture Environmentally Friendly Use Period (EFUP) Caution for local load Entire surface load This symbol indicates that the flat panel sensor supports the automatic X-ray detection function. With this function, operations for making an exposure start when the flat panel sensor detects X-rays. * This function is not supported by the DR-ID 900PU. No Stepping on Surface Refer to Instruction Manual/Booklet 2-6 DR-ID 900PU Operation Manual 897N102280A Chapter 3 Basic Operation 3.1 Preparing the Flat Panel Sensor This section describes how to prepare the flat panel sensor. 3.1.1 Type of Flat Panel Sensor Wireless communication mode or wired communication mode is available. When used in wireless communication mode, an access point*1, battery pack (optional) and battery charger (optional) are required. *1 In the countries other than the U.S., an access point is not included as a component of the system. For details including installation, consult our official dealer. • Product compliant with IEC60950, UL60950, PSE or JIS • Compliant with IEEE802.11n [W52] (in the 5.2GHz band) /36, 40, 44, 48ch • WLAN interface: 1000BASE-T/100BASE-TX (minimum requirements) • LAN interface: 1000BASE-T/100BASE-TX (minimum requirements) • Available OS: Linux • Compliant with UL • Compliant with FCC part15 Basic Operation CAUTIONS Use only one access point. A communication error may occur if two units or more are used. 3.1.2 Number of the Connectable Flat Panel Sensors To enable the flat panel sensor, its ID needs to be registered in advance by a FUJIFILM dealer. Up to five flat panel sensors can be registered. Up to four flat panel sensors can be connected in wired or wireless communication mode in DR-ID 900PU. However, either of the following conditions must be met: a) Two DR-ID 911SE flat panel sensors are connected in wired communication mode. (More than three flat panel sensors cannot be connected in wired communication mode.) b) Any two of the DR-ID 601SE, DR-ID 602SE, DR-ID 611SE and DR-ID 613SE flat panel sensors are connected in wired communication mode. (Connection example) Wired communication mode Wireless communication mode Ethernet switch (Hub) Flat panel sensor Flat panel sensor Flat panel sensor Flat panel sensor Power supply unit (DR-ID 900MP) Control cabinet (DR-ID 900MC) Power supply unit (DR-ID 900MP) Image processing unit Access point When multiple flat panel sensors are connected, make sure that the READY lamp among the status lamps of the flat panel sensor to be used for an exposure is lit. DR-ID 900PU Operation Manual 897N102280A 3-1 3.1.3 Connecting/Disconnecting the Flat Panel Sensor Connector When used in wireless communication mode, disconnect the connector. Disconnect the connector. Press the latches on both sides of the connector. Connect the connector. Press the connector into the insertion section. Make sure that the latches on both sides are properly engaged when connecting the connector. If the flat panel sensor is used with the connector inserted incompletely, the flat panel sensor may turn off. Basic Operation Connect/Disconnect the connector straight to the flat panel sensor. If connected/disconnected at an angle, the connector may be damaged. 3-2 DR-ID 900PU Operation Manual 897N102280A 3.1.4 Inserting/Removing the Flat Panel Sensor into/from the Radiographic Examination Stand [1] In the case of the flat panel sensor DR-ID 911SE The DR-ID 911SE cannot be mounted to any radiographic examination stand other than one specified by FUJIFILM Corporation. For details, refer to the operation manual of the radiographic examination stand. [2] In the case of the flat panel sensors DR-ID 601SE/ DR-ID 602SE/DR-ID 611SE/DR-ID 613SE Follow the procedure below to insert/remove the flat panel sensor into/from the radiographic examination stand. For details, see the Operation Manual for the radiographic examination stand CAUTIONS For the positioning at the time of inserting/removing the flat panel sensor, see the Operation Manual for the radiographic examination stand. Basic Operation CAUTIONS Be careful not to have your fingers caught when inserting/removing the flat panel sensor into/ from the radiographic examination stand. [1] Upright type Set the flat panel sensor to the upper part of the tray. Push the tray back into place after setting the flat panel sensor. When inserting from the right-hand side CAUTIONS When inserting the flat panel sensor into the radiographic examination stand, direct the exposure plane toward the X-ray tube. Pull out the tray. Tray Insert the flat panel sensor into the cassette receive while the connector directed to the upper right, and then move it downwards. When inserting the flat panel sensor from the lefthand side, direct the connector to the lower left. Connector Connector Cassette receive Remove the flat panel sensor after use. Pull out the tray, push the cassette receive downwards, and then remove the flat panel sensor. Push the tray back into place. DR-ID 900PU Operation Manual 897N102280A 3-3 [2] Bed type Push the tray back into place by using the handle after setting the flat panel sensor. Remove the flat panel sensor after use. CAUTIONS When inserting the flat panel sensor to the radiographic examination stand, direct the exposure plane upwards. Pull out the tray by using the handle. Hold the handle and pull out the tray. Remove the flat panel sensor while pulling the cassette stopper, and then push the tray back into place. Tray Basic Operation Pull the cassette stopper, and set the flat panel sensor so that its center mark is aligned with the center of the stopper. Position the connector of the flat panel sensor as shown in the figure below. Connector Cassette stopper Center mark When setting the flat panel sensor horizontally, position the connector as shown in the figure below. Connector 3-4 DR-ID 900PU Operation Manual 897N102280A 3.1.5 Changing the Direction of the Flat Panel Sensor Connector The direction of the connector of the flat panel sensor can be changed, depending on how it is inserted into the radiographic examination stand. To change the direction, contact a FUJIFILM dealer. When shipped 3.1.6 After changing the direction Basic Operation Charging the Battery Pack (optional) for the Flat Panel Sensor Use the battery charger recommended by FUJIFILM Corporation. For details on operations, refer to the instruction manual for the battery charger. DR-ID 900PU Operation Manual 897N102280A 3-5 3.1.7 Installing/Removing the Battery Pack (optional) for the Flat Panel Sensor Follow the procedure below to install/remove the battery pack for the flat panel sensor. When installing/removing the battery pack, place the flat panel sensor on a flat place. Remove the battery cover. Place the flat panel sensor with the back side facing upward, and then simultaneously slide both the battery lock release latches outward to remove the battery cover. Slide the battery pack along the dent of the battery section of the flat panel sensor toward the connector terminal. Align the guide mark of the battery pack with that of the flat panel sensor, and push the battery pack in to install it. Make sure that battery pack is securely installed. Pushing the battery pack in with the guide marks misaligned may damage the connector terminal. Basic Operation When the battery pack is installed, the power is automatically turned on. Battery cover Guide marks Install the battery pack. Make sure that the battery lock release latches are released. When the battery lock release latches are released Battery pack • To remove the battery pack, perform the same procedure as Step 1 (removing the battery cover). • To install the battery cover, perform the same procedure as Step 2 (installing the battery pack) Battery lock release latches 3-6 DR-ID 900PU Operation Manual 897N102280A 3.2 Starting Up and Shutting Down the DR-ID 900PU This section explains how to start up and shut down the DR-ID 900PU. 3.2.1 Starting Up the DR-ID 900PU Press the ON side of the main switch of the power supply unit. Start up the DR-ID 900PU with the initial settings properly made by our official dealer. 3.2.2 Shutting Down the DR-ID 900PU Press the OFF side of the main switch of the power supply unit. Basic Operation DR-ID 900PU Operation Manual 897N102280A 3-7 3 Basic Operation 3-8 DR-ID 900PU Operation Manual 897N102280A Chapter 4 Daily Inspection and Maintenance 4.1 Daily User Inspection and Maintenance During maintenance and inspection, strictly observe precautions contained in “Chapter 1 For Safe Operation” in this manual for you to use the DR-ID 900PU under best conditions. 4.1.1 Periodical Inspection Inspection Every Three Months Using a vacuum cleaner, remove any dirt or dust accumulated in each unit of the equipment once every three months. Clean then with a slightly moistened soft cloth and wipe off any moisture with a dry cloth. See “2.2 Unit Names and the Functions” (page 2-2). No. Flat panel sensor No. Unit Power supply unit Air filter Clean the air filter on the rear of the power supply unit with a vacuum cleaner. Push down the lever at the top of the louver-andfilter assembly, and clean the air filter with a vacuum cleaner after detaching it from the assembly. No. Unit Daily Inspection and Maintenance Unit Power supply unit Air filter (1) Air filter Be sure to turn off the equipment before cleaning the air filter or the remote switch (optional). DR-ID 900PU Operation Manual 897N102280A 4-1 4 Daily Inspection and Maintenance 4-2 DR-ID 900PU Operation Manual 897N102280A Appendix A Specifications A.1 Specifications Specifications of the DR-ID 900PU are shown below. A.1.1 Reduced Equivalent (DR-ID 900) Peak reduced equivalent on the front panel of the flat panel sensor: 0.5 mmAl A.1.2 Power Supply Conditions Rated voltage Input current Frequency : 100 - 240 V ~ : 2 - 0.84 A : 50 - 60 Hz A.1.3 Environmental Conditions (1) Operating Conditions Temperature : 15°C (15%RH) - 30°C (80%RH) Humidity : 15%RH (15°C) - 80%RH (30°C) (no dew condensation) Atmospheric pressure : 700hPa - 1060hPa Appendix A Specifications (2) Non-operating Conditions (Environmental conditions under which power can be supplied) Temperature : 5°C - 35°C (no dew condensation) Humidity : 10%RH - 80%RH (no dew condensation) Atmospheric pressure : 700hPa - 1060hPa A.1.4 Image performance The flat panel sensors comply with the IEC 62220-1 standard (Medical electrical equipment –Characteristics of digital X-ray imaging devices) as general X-ray devices. To ensure optimal image quality, it is recommended that you do not use the flat panel sensor near devices (motor, transformer, switching supply, etc.) that generate electromagnetic noise. DR-ID 900PU Operation Manual 897N102280A A-1 Appendix A Specifications A-2 DR-ID 900PU Operation Manual 897N102280A Appendix O Use of Optional Items O.1 Optional Items Name Retaining bracket for MP Description A set of an anchor and a fixture, which is used for securing the power supply unit to the floor. For the external view, see “O.2 Using the Retaining Bracket for MP” (page O-2). SE cable A cable that connects the flat panel sensor and the power supply unit(s). When a second or third flat panel sensor is added to the system, this cable is used for reconnecting flat panel sensors, for example. X-ray camera connection cable A signal cable that connects the power supply unit and the X-ray equipment (shot signal). Cable length : 15m (49.2 ft) Battery pack A battery pack for the flat panel sensor. For precautions, charging and installing/removing, see pages 1-5, 1-6, 3-5 and 3-6. Battery charger A battery charger for the battery pack. For precautions, external view and charging, see pages 1-5, 1-6, 2-1 and 3-5. Appendix O Use of Optional Items DR-ID 900PU Operation Manual 897N102280A O-1 O.2 Using the Retaining Bracket for MP Cap Bolt Fixture Anchor Contact a FUJIFILM dealer for installation of the Retaining bracket for MP. Appendix O Use of Optional Items O-2 DR-ID 900PU Operation Manual 897N102280A Radio frequency (RF) compliance information Compliance with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. Le présent appareil est conforme aux la partie 15 des règles de la FCC et CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. DR-ID 601SE/DR-ID 602SE/DR-ID 611SE/DR-ID 612SE/DR-ID 613SE 911 has been tested and found to comply with FCC/IC radiation exposure limits set forth for an uncontrolled RSS-102 ofCthe radio environment and meets the FCC radio frequency (RF) Exposure Guidelines and in Supplement to IC OET65 frequency (RF)of Exposure rules.frequency (RF) Exposure rules. and RSS-102 the IC radio Les connaissances scientifiques dont nous disposons n’ont mis en évidence aucun problème de santé associé à l’usage des appareils sans fil à faible puissance. Nous ne sommes cependant pas en mesure de prouver que ces appareils sans fil à faible puissance sont entièrement sans danger. Les appareils sans fil à faible puissance émettent une énergie radioélectrique (RF) très faible dans le spectre des micro-ondes lorsqu’ils sont utilisés. Alors qu’une dose élevée de RF peut avoir des effets sur la santé (en chauffant les tissus), l’exposition à de faibles RF qui ne produisent pas de chaleur n’a pas de mauvais effets connus sur la santé. De nombreuses études ont été menées sur les expositions aux RF faibles et n’ont découvert aucun effet biologique. Certaines études ont suggéré qu’il pouvait y avoir certains effets biologiques, mais ces résultats n’ont pas été confirmés par des recherches supplémentaires. DR-ID 601SE/DR-ID 602SE/DR-ID 611SE/DR-ID 612SE/DR-ID 613SE a été testé et jugé conforme aux limites d’exposition 911 aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. 5.15-5.25GHz band is restricted to indoor operations only. Labande 5150-5250 MHz est restreints à une utilisation à l’intérieur. (This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.) DR-ID 900PUOperation OperationManual Manual 897N102280A FDR D-EVO 897N101473L Maintenance and Inspection Compliance with FCC requirement 15.407(C) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmitor operational failure. Maintenance and Inspection 1 Maintenance and Inspection Items Assigned to Specified Dealer For periodical inspection of the equipment and necessary arrangements, consult our official dealer or local representative. Periodical Maintenance Make sure that the periodical maintenance and inspection assigned to our official dealer are performed as specified. Maintenance and Inspection Items Assigned to Specified Dealer Periodical Maintenance and Inspection Items Period Checking of the image Every year Checking of the operation record by referring to the error log Every year Checking of the internal units Checking of the S value Every 2 years Every 6 months Main Periodical Replacement Parts * It is recommended that the battery pack (optional) be replaced once a year. If the duration of use exceeds one year, the capacity of the battery pack will decrease. The cycles of periodical maintenance and inspection and of parts replacement differ depending on the usage and the daily operation time. For details, contact us directly or our official dealer. Maintenance and Inspection DR-ID 900PU Operation Manual 897N102280A FUJIFILM MEDICAL SYSTEMS U.S.A., INC. 419 WEST AVENUE, STAMFORD CT 06902, U.S.A.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : 14539 Create Date : 2014:02:27 14:10:00+09:00 Modify Date : 2014:02:27 14:10:00+09:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Instance ID : uuid:f9a061b5-9b3d-4408-ac7d-d1b268edebb6 Document ID : adobe:docid:indd:ff34819f-e7a4-11e2-b857-91bb9b604bc3 Rendition Class : proof:pdf Derived From Instance ID : 04f7f465-abda-11e2-a71f-881104c3288d Derived From Document ID : adobe:docid:indd:27637e50-aae9-11e2-940f-c6b4539c1c3f Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Y Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : uuid:565b0cc6-7b3a-479a-bd40-d70169b2b5ee, uuid:efeba194-9a4c-429f-bce4-f2cdb3081383, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:71d4cc3e-59c8-4bdb-bfb7-61ac158d9f0b, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:60f94163-2e7f-4d5c-99c0-eaa887f11b71, uuid:e3e79bbb-ebf5-4674-918d-ba99b6d64816, uuid:3a58792a-44b7-4732-a2fc-d41705766f78, uuid:f44892d6-07ea-477d-a919-d14776f69a35, uuid:b7054408-2934-4efe-b31a-887d9fb32513, uuid:3277154a-6cee-43b5-aac3-ee37c252ad70, uuid:4db3233b-4eb6-4eed-9dd0-1b5474329ec7, uuid:afa849cf-f3f5-4971-8f67-f1f272b80a34, uuid:c4a7406b-1b56-4c20-9cd1-0a87a0b184cf, uuid:fea3b5a5-16a3-4247-8a06-05197b951a6d, uuid:327ec036-6dba-4836-ada0-0154fa331bf6, uuid:54265582-5957-47c6-ab1d-dd307656bbff, uuid:a4fce28c-1852-4faa-b222-bf5cee4835c0, uuid:8c697a41-4eeb-4ce1-bd25-4baede809c09, uuid:19a96e51-c842-4f47-a3e0-00c203b840b9, uuid:de157239-9389-41f8-890f-77d3cc13f2f9, uuid:49045d66-dce2-4088-9354-a68dd6a35694, uuid:cb7a8540-e5da-4b93-938f-ad31e98a8e09, uuid:848924e0-c803-4292-8cae-ba6f0a37685e, uuid:239a2865-6e6b-41a6-b242-bf8ee05794e3, uuid:55a5d756-d546-46a7-8309-70f7d0566940, uuid:ed3e2b01-65f3-45b7-baa4-336a6358b8bb, uuid:a9778d9a-f176-4ce4-be77-8b7aa7c2a22d, uuid:0dc7ae36-ae8b-431a-b606-7d0ab7d6b232, uuid:213f48cd-6c58-4105-a2f9-838be4ac2b3c, uuid:f61a73cb-0a6c-474e-9afd-46068c5292b6, uuid:851e0b1b-6249-4f67-a8b8-3a4ff973b5b4, uuid:4550a524-1eb9-4a1b-b9c1-8ffacdfbdab3, uuid:d071a855-b3de-4ba3-8e7f-00f9da63ad51, uuid:79968940-7e3e-4ab0-acd5-c066430ea859, uuid:b4c5cde2-e5cb-4876-9b6c-c1dfeb4089f0, uuid:50eee83e-53c0-4c3c-bae7-2627e064fba6, uuid:9ff33229-93e3-49c0-8696-fb84868aaf8d, uuid:83b09661-b001-4efc-bc1f-acf20e2c9436, uuid:00ca7917-6beb-4e8e-af84-110259dd5fe3, uuid:9defadc9-8808-4b85-89f6-e3f404ee0329, uuid:e9a17b62-c031-4150-a5e8-8620de78ece5, uuid:32ff5f50-d0a1-4894-a8e1-b44f28d7b90d, uuid:00a7d6c0-0d74-49dc-88e3-1616bc7821e3, uuid:3626599d-8020-429e-884d-e031ec523142, uuid:e5098b91-05d1-4220-aa27-c3cd117a180e, uuid:c006b78b-cb51-4664-83d9-da27b2ef6960, uuid:07944d9b-af06-4c97-b199-4b010c4d185f, uuid:c6f99a16-0c67-4aef-b68d-4bcc65de9057, uuid:daa1c9b3-8657-47dc-99b5-e41527054789, uuid:63cd7b60-e278-4142-ab5b-292450f33bc6, uuid:a2fe7c12-1227-4732-b2f3-460e40670662, uuid:60c8c920-ae2f-4cfd-a4e2-1cbbbac0aa9b, uuid:7c67c129-7c45-46fa-987e-e36785fb98b0, uuid:b371a5a1-bc3d-48d0-ab59-c44785c2ec45, uuid:47e2f5a7-3f40-43c6-bc15-386bd5170fdf, uuid:d73d6e65-0a24-4b26-b79c-d3b4d4bd6a49, uuid:ba6e9f4b-ca9a-4448-bb20-750067354eae, uuid:2f30c298-854f-45ca-aa71-ed4278d34cb2, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:d97809e8-307e-4c7c-8810-aeb507b39982, uuid:5243ec11-61b6-41c8-801c-6b27c25db171, uuid:8040b4d1-90d4-4d67-b71d-ef6561c561c5, uuid:d97809e8-307e-4c7c-8810-aeb507b39982, uuid:f51d5117-1e66-4298-9892-0918a0ac05a2, uuid:6a4b12dc-2150-446a-b624-d16c5b4f09f6, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:b4e64419-7389-4d67-aea5-6cda1734b65c, uuid:e2074b43-4953-42b7-85ac-6c82b69a39fc, uuid:009955f9-f3cb-4d85-a0e3-b4329a0984a4, uuid:cafd2fe5-f703-4797-88c3-193e127df10a, uuid:d97809e8-307e-4c7c-8810-aeb507b39982, uuid:bd4df52b-3495-42cc-bd97-89024c4025cb, uuid:88405143-6777-4de5-b4e8-843131254def, uuid:9a2be79c-0e11-4db4-962b-bccbcc66d576, uuid:a576ea40-e40e-4bed-865f-dba2c07b1ebc, uuid:f0e3cf91-41b0-4791-8e6e-b29c12501f5f, uuid:d97809e8-307e-4c7c-8810-aeb507b39982, uuid:71f54c4f-4227-4c53-bd0b-42835efb4d92, uuid:5c03253a-eee1-4ff4-9e27-a664b925b162, uuid:fc4540db-0d33-43d9-a741-e92623c94231, uuid:d97809e8-307e-4c7c-8810-aeb507b39982, uuid:c741bd86-cabf-4070-820e-98cea71f4712, uuid:14d7b344-e6c3-4c90-8adc-a047a8c145b3, uuid:d97809e8-307e-4c7c-8810-aeb507b39982, uuid:d97809e8-307e-4c7c-8810-aeb507b39982, uuid:e5753fe4-3c72-4e2b-943b-b93b3a228202, uuid:d97809e8-307e-4c7c-8810-aeb507b39982, uuid:d97809e8-307e-4c7c-8810-aeb507b39982, uuid:6a4b12dc-2150-446a-b624-d16c5b4f09f6, uuid:2c57df76-e385-459e-8d18-0f882397765f, uuid:d97809e8-307e-4c7c-8810-aeb507b39982, uuid:7e221a7f-e37e-42d8-9db1-289215001294, uuid:7e221a7f-e37e-42d8-9db1-289215001294, uuid:7e221a7f-e37e-42d8-9db1-289215001294, uuid:97c96966-d6d7-4021-9f30-02e8468f5df3, uuid:d97809e8-307e-4c7c-8810-aeb507b39982, uuid:8a1ac79f-cf49-4198-8468-b56054517f9e Manifest Reference Document ID : uuid:DF1BBC8A4846DD11A2E299E0475435CB, uuid:2763B9A2862CDD1199EF8DEFB306B087, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:B068B7F70B47DD1186A1F17A8213714A, uuid:9C31D028E3D8DE11AB82B139C71A6298, uuid:5212A3C7BAA0E11187079B24CB399CD4, uuid:75F16CF239D3DE119089A81FBCCAD835, uuid:77F16CF239D3DE119089A81FBCCAD835, uuid:79F16CF239D3DE119089A81FBCCAD835, uuid:2A75AEFAC39CE0119C07891EF74A88E1, uuid:EA0D19EBFAE0E11184AAB738A2E00EBE, uuid:58522144356BE011B956DA721D276BC0, uuid:2E75AEFAC39CE0119C07891EF74A88E1, uuid:A8101837630BE211A6569064359ADF45, uuid:7C033E0E10FBE111A9C5FB591A8D43F8, uuid:191AB0B8DC2DE011BD119CEF5962A8A7, uuid:DA3518780434E011802BC636714AF635, uuid:FD361EB92C9DE0118ADCE7599484BD21, uuid:D7B0D755B6A3E0119AC4972D13C2BD57, uuid:B9F2DAC82C6BE011AE73B23E5881B5AC, uuid:D9B0D755B6A3E0119AC4972D13C2BD57, uuid:AE101837630BE211A6569064359ADF45, uuid:09C754D2F6FDDF119DC093DA87C69AE1, uuid:571CBBC4A3FEE0118A0CF025936FB452, uuid:C1DE187C0FFBE111A9C5FB591A8D43F8, uuid:30CEC2506A0BE21191A1E9B84BBB9EB4, uuid:32CEC2506A0BE21191A1E9B84BBB9EB4, uuid:0DC754D2F6FDDF119DC093DA87C69AE1, uuid:F5A7A78673EBDE11850BB3EFB099F7A6, uuid:64838633BA47E11184ABF25EAD945438, uuid:074078582CDBDF1188D685586DF07EAF, uuid:C3DE187C0FFBE111A9C5FB591A8D43F8, uuid:CA7B390C57DEDE11B909C067DFFAEE9D, uuid:0B1071F5C1FAE01189E9C8D73E461D29, uuid:0D1071F5C1FAE01189E9C8D73E461D29, uuid:0DE97E0B7E1FE011A43ED7AED53F88F3, uuid:FF361EB92C9DE0118ADCE7599484BD21, uuid:94824E4F2E9DE0118ADCE7599484BD21, uuid:96824E4F2E9DE0118ADCE7599484BD21, uuid:98824E4F2E9DE0118ADCE7599484BD21, uuid:9A824E4F2E9DE0118ADCE7599484BD21, uuid:9C824E4F2E9DE0118ADCE7599484BD21, uuid:F3C5DA702E9DE0118ADCE7599484BD21, uuid:F1C5DA702E9DE0118ADCE7599484BD21, uuid:F9C5DA702E9DE0118ADCE7599484BD21, uuid:F7C5DA702E9DE0118ADCE7599484BD21, uuid:F5C5DA702E9DE0118ADCE7599484BD21, uuid:5D4DF4992E9DE0118ADCE7599484BD21, uuid:594DF4992E9DE0118ADCE7599484BD21, uuid:574DF4992E9DE0118ADCE7599484BD21, uuid:E90BA0F3C598E1119312F01A7785F73F, uuid:E6A5E78E8FA0E111856AB310F51A6C72, uuid:EB0BA0F3C598E1119312F01A7785F73F, uuid:E4A5E78E8FA0E111856AB310F51A6C72, uuid:0ECC781BC69CE0119C07891EF74A88E1, uuid:0D1071F5C1FAE01189E9C8D73E461D29, uuid:0B1071F5C1FAE01189E9C8D73E461D29, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:FBE05DEE84F2DD11B564A6070FBA0A4E, uuid:C470380909C2DF11AFBCEDD0554BFD8A, uuid:C270380909C2DF11AFBCEDD0554BFD8A, uuid:FBE05DEE84F2DD11B564A6070FBA0A4E, uuid:DE32EFC333B5E1119247CA225EA22D50, uuid:B57DD9B8B572DF11A2EADA9221AA24CD, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:954CDBF2D1D5DF119A388E0897E07540, uuid:974CDBF2D1D5DF119A388E0897E07540, uuid:97878F3DD7D5DF119A388E0897E07540, uuid:99878F3DD7D5DF119A388E0897E07540, uuid:FBE05DEE84F2DD11B564A6070FBA0A4E, uuid:9B878F3DD7D5DF119A388E0897E07540, uuid:8BCC03F23468DD119DDFC08DE41116AE, uuid:9F878F3DD7D5DF119A388E0897E07540, uuid:A1878F3DD7D5DF119A388E0897E07540, uuid:02AF0324DFD5DF119A388E0897E07540, uuid:FBE05DEE84F2DD11B564A6070FBA0A4E, uuid:04AF0324DFD5DF119A388E0897E07540, uuid:06AF0324DFD5DF119A388E0897E07540, xmp.did:DFC80D7F85D0E111B847B10CC2A584B7, uuid:FBE05DEE84F2DD11B564A6070FBA0A4E, uuid:8DDE0CCCAAD2DF119010A093C11762FD, uuid:26D2015900A3E011BE9DE16E1B04455D, uuid:FBE05DEE84F2DD11B564A6070FBA0A4E, uuid:FBE05DEE84F2DD11B564A6070FBA0A4E, uuid:2AD2015900A3E011BE9DE16E1B04455D, uuid:FBE05DEE84F2DD11B564A6070FBA0A4E, uuid:FBE05DEE84F2DD11B564A6070FBA0A4E, uuid:B57DD9B8B572DF11A2EADA9221AA24CD, uuid:4E6F7EB2CA0BDF11981FE467A54CD7F8, uuid:FBE05DEE84F2DD11B564A6070FBA0A4E, uuid:2C189293B672DF11A2EADA9221AA24CD, uuid:2C189293B672DF11A2EADA9221AA24CD, uuid:2C189293B672DF11A2EADA9221AA24CD, uuid:371F2224BAD1DF11AD85CF98ECCCCD77, uuid:FBE05DEE84F2DD11B564A6070FBA0A4E, uuid:B4353E9A2D3DDF1194398A1439FB47B5 Metadata Date : 2014:02:26 10:13:13+09:00 Creator Tool : Adobe InDesign CS3_J (5.0.4) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 6673 bytes, use -b option to extract) Format : application/pdf Title : DR-ID900PU Manual (2nd Ed.)f.pdf Creator : 14539 Producer : Acrobat Distiller 10.1.2 (Windows) Trapped : False Page Count : 39EXIF Metadata provided by EXIF.tools